FLUID POWER COMPONENTS & SYSTEMS

Transcription

1 FLUID POWER COMPONENTS & SYSTEMS

2 Page Thank you for your interest in Motion Controls LLC. We have been building high quality air and hydraulic cylinders for 50 years in the USA. Motion Controls LLC is a small company in Southeast Wisconsin paying attention to detail and standards for our customers. This Catalog features our newest product lines. We have integrated two of our most popular air cylinders with our new patented electronic rod position sensing technology; QVLA. For the first time rod position can be reported with a simple analog voltage all within an NFPA footprint as in our K Series. The sensor is also available in our non-nfpa D Series. In addition, the technology uses no magnets, works in high vibration environments with or without ferrous metals and impervious to weld fields. TABLE OF CONTENTS Warranty Quick Reference Guide 3 Page Electronic embedded insight Actuators: Featuring our patented QVLA Sensor technology. Section 1: insight Analog Series (reporting VDC proportional to stroke) 4 NAD Series Dimensions (non-nfpa) cylinders 5 NAK Series Dimensions (NFPA) cylinders 6 How to Order insight Analog Series 7 Section : insight PPC Series ( programmable positions) 8 NSD Series Dimensions (non-nfpa) cylinders 9 NSK Series Dimensions (NFPA) cylinders 10 How to Order insight PPC Series 11 Mounts for NAD and NSD 1,13 Mounts for NAK and NSK 14,15,16,17 Section 3: Systems QVLA Explanation and discussion. 18 Systems QVLA and Enfield S valve in partnership. 19 A complete list of distributors is on the web: or if you like call Customer Service at for the one closest to you.

3 Page WARRANTY: ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED IN LIEU OF THIS LIMITED WARRANTY. Motion Controls LLC. (Seller) warrants that its products are free from defects in material and workmanship for a period of one (1) year from the date of shipment from the factory. O RINGS AND SEALS ARE SPECIFICALLY EXEMPTED FROM THIS WARRANTY. Seller does not accept responsibility of any type for, and this warranty shall not apply to, any of its products that have been subjected to improper installation or application, negligence, tampering, abuse, or which have been disassembled and/or repaired or altered by anyone other than the Seller. Seller s liability under this warranty shall extend only to replacement or correction, F.O.B. our factory, of any part or product determined by Seller s inspection as not conforming to this warranty. SELLER S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR RE- PLACEMENT OF THE PRODUCT, AT ITS OWN OPTION, AS SET FORTH HEREIN. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR DAMAGE TO ANY OTHER PROPERTY OR PER- SONS CAUSED BY ANY DEFECTS OF THE PRODUCTS, DAMAGES BASED UPON INCONVEN- IENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, COMMERCIAL LOSS OR ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE. BUYER IS SOLELY REPONSIBLE FOR DETERMINING THE SUITABILITY OF GOODS SOLD HEREUNDER FOR USE BY BUYER. GOODS NOT MANUFACTURED BY MOTION CONTROLS LLC.: Goods furnished subject only to the manufacturer s warranties, if any, and without warranties, expressed or implied, by Motion Controls LLC. Any description of the goods sold hereunder, including any references to Buyer s specifications, or any descriptions in catalogs, circulars and other written material published by seller is for the sole purpose of identifying such goods and shall not create an express warranty that the goods shall conform to such description. APPLICATION LIMITATIONS: Motion Controls LLC. products are not recommended, designed, warranted or approved for use in: Any product used under the Federal Highway Safety Act; including, but not limited to, steering or braking systems for passenger vehicles or on-highway vehicles. Aircraft or space vehicles. Ordnance equipment. Life support equipment. Any product used under U.S. Nuclear Regulatory Commission Rules and Regulations. Consult factory for details or questions. PERFORMANCE ASSURANCE: All Motion Controls LLC. Components are tested individually at the factory. ASSURANCE OF SUITABILITY OF ALL MOTION CONTROLS LLC. PRODUCTS IN THE BUYER S APPLICATION IS THE RESPONSIBILITY OF THE BUYER. All information provided by Motion Controls LLC. is designed to assist the Buyer in selecting the proper product. Actual performance of a Buyer s equipment cannot be reproduced in Motion Controls LLC. facilities. It is recommended a prototype, test, and qualification program be performed by the buyer to assess suitability of Motion Controls LLC. product.

4 Page 3 STANDARD CYLINDERS Series Model Bore Rod Dia. D (RA1 Standard Rod) K (RA Standard Rod) NFPA D1 1 1/4" 3/8" 3/8-16 1/4-0 1/4-0 1/4-8 1/8 3-17/3 D4 1 3/4" 5/16-4 1/4 D30 " 1/4-8 3/4" 3/4-10 1/-13 1/ /64 D49 1/" 5/16-4 3/8 D70 3" D96 3 1/" D /" K /" 5/8" 5/8-18 7/16-0 7/16-0 1/ /8 K " /4-16 3/ K /8" 5/8-18 7/16-0 7/ /8 " 3/8 K " /4-16 3/ /16-4 K /8" 5/8-18 7/16-0 7/ /4 1/" K /8 1" /4-16 3/4-16 K /8 3 1/4" K /8" 1 3/ /8 3/8-4 K " 1" /4-16 3/4-16 1/ 5-5/8 K /8" 1 3/ /8 K " /4-16 3/ /8 5" K /8 1 3/8" 1 3/ /-0 K /8 6" 3/4 K /4" 1 3/ / / /8 ELECTRONIC CYLINDERS NSD (RA1 Standard Rod) NFPA NSK (RA Standard Rod) NAD (RA1 Standard Rod) NFPA NAK (RA Standard Rod) Programmable insight PPC with KEYPAD NSD1 1 1/4" 3/8" 3/8-16 1/4-0 1/4-0 1/4-8 1/8 4-17/3 NSD4 1 3/4" 5/16-4 1/4 NSD30 " 1/4-8 3/4" 3/4-10 1/-13 1/ /64 NSD49 1/" 5/16-4 3/8 NSD70 3" NSK150 5/8" 5/8-18 7/16-0 7/ /8 1 1/" 1/4-8 NSK15 1" /4-16 3/ /4 NSK00 5/8" 5/8-18 7/16-0 7/ /8 " NSK0 1" /4-16 3/ /16-4 NSK50 5/8" 5/8-18 7/16-0 7/ /4 1/" 3/8 NSK5 5-1/8 1" /4-16 3/4-16 NSK30 1/ 5-5/8 3 1/4" 3/8-4 NSK3 1 3/8" 1 3/ /8 NAD4 1 3/4" 5/16-4 1/4 NAD30 " 1/4-8 3/4" 3/4-10 1/-13 1/-13 NAD49 1/" 5/16-4 3/8 NAD70 3" NSD96 3 1/" NSD /" insight Analog Reporting VDC Output 1" 1-8 For thread styles (KK): RA1 Full Male RA Reduced Male 1" 1-8 3/4-10 3/4-10 1/-0 1/ Rugged Affordable Resolution 3/4-10 RA3 Small Female Tie-Rod Dia. and Thread. Port Size NPT. Single End, No Cushion, 0 Stroke, ZB Dimension. 5-35/ /64 3/4-10 1/-0 1/ 5-35/64 NAK150 5/8" 5/8-18 7/16-0 7/ /8 1 1/" 1/4-8 NAK15 1" /4-16 3/ /4 NAK00 5/8" 5/8-18 7/16-0 7/ /8 " NAK0 1" /4-16 3/ /16-4 NAK50 5/8" 5/8-18 7/16-0 7/ /4 1/" 3/8 NAK5 5-1/8 1" /4-16 3/4-16 NAK30 5-5/8 3 1/4" NAK3 1 3/8" 1 3/ /8 3/8-4 NAK400 1" /4-16 3/ /8 4 1/ NAK40 1 3/8" 1 3/ /8 NAK500 1" /4-16 3/ /8 5 NAK50 6-1/8 1 3/8" 1 3/ / -0 NAK /8 6 3/4 NAK60 1 3/4" 1 3/ / / /8 MAX Pressure Rating 50 psi 135 psi 135 psi

5 Page 4 insight Analog Reporting Cylinder Motion Controls LLC now offers our patented QVLA sensing technology embedded within our air cylinders. Upgrade and update equipment with old reed switches, expensive, fragile and bulky transducers or external potentiometers with insight Analog Reporting Cylinders. Now for the first time repeatable proportional to rod position voltage signal is available in an NFPA footprint and our popular non-nfpa D Series. No additional electronics needed. Position reported with analog voltage via a three wire M8 IP67 cable carrying power, ground and signal. Voltage output is.5 to 9.5 VDC proportional to stroke. NAK Series is equal to our K Series with insight Analog. NAD Series is equal to our D Series with insight Analog. Following this section is a matching proportional valve from Enfield Technologies to compliment your cylinder and your control methods. See more on the S valve at and page 19 in this catalog. Electronic Features and Specifications FAST 4kHZ Non-Contact Weld Field Immune Temperature Compensated LED life over 50 years Repeatability 1% of stroke (Call for longer stroke specifications.) No Ferrous Materials OUTPUT,5-9.5 VDC proportional to stroke (Custom available on request,) MECHANICAL FEATURES Chrome Plated Steel Piston Rod Composite Rod Bearing PTFE Cap Seals for Piston Rod PTFE Cap Seals for Piston PTFE Solid Piston Bearing Anodized Aluminum Tube Non-Lubrication Machined Solid Aluminum End Caps SYSTEM REQUIREMENTS Pneumatic Operation Only Only Dry Air 0.3 Micron fine grade coalescing filter with 5 micron pre-filter. 135 PSI Max Operating Temperature -0 F to 170 F Chrome Plated Steel Piston Rod Composite Rod Bearing PTFE Cap Seal Anodized Aluminum. Composite, Or Steel Tubing Available. PTFE Piston Bearing PTFE Cap Seal Embedded QVLA Electronics M8 socket Connector.

6 Page 5 Analog Reporting NAD Dimensions = ( D Series SENC) NAD SERIES FM RA1 ROD DIA. MODEL A D G C P Y SN XT ZB CC EE MM 4 1-1/ 5/8 1-3/16 3/4-3/8 1-15/3-39/ /3 4-35/64 3/4-10 1/4 3/ / 5/8 1-3/16 3/4-3/8 1-15/3-39/ /3 4-35/64 3/4-10 1/4 3/ / 5/8 1-3/16 3/4-7/16 1-7/64-39/ /3 4-35/64 3/4-10 3/8 3/ / 5/8 1-3/16 3/4-13/3 1-7/16-39/ /3 4-35/64 3/4-10 3/8 3/ /8 7/8 1-7/ / /16 3-7/64 1-3/3 5-35/ / /8 7/8 1-7/ / /16 3-7/64 1-3/3 5-35/ / 1 M8 Connector E R BC RT TN NT ALL MODELS MOD EL E TN BC RT R NT 4-3/8 5/3.49 5/16-4X9/ /16-4X9/3 30-3/8 5/3.65 1/4-8X3/ /16-4X9/3 49-7/8 1-1/ /16-4X9/ /16-4X1/ /8 1-1/ /16-4X9/ /16-4X9/ /8 1-7/ /-0X3/ /-0X1/ /8-1/ /-0X3/ /-0X1/

7 NFPA Page 6 NAK Dimensions = ( K Series) Analog Reporting BASIC SINGLE END CYLINDER DIMENSIONS ROD NPTF BORE DIAM. P G J F SN NT EE A W Y XT ZB 5/8 3/4 5/8 1-15/16 4-5/8 1-1/ -1/8 1-1/ 1 3/8-1/4 1/4-0 X 17/64 3/ /8 1-3/8-5/16 5 5/8 3/4 5/8 1-15/16 4-5/8-1/8 1-1/ 1 3/8-1/4 5/16-18 X 3/8 3/ /8 1-3/8-5/16 5 5/8 3/4 5/8 1-15/16 4-3/4-1/ -1/4 1-1/ 1 3/8-3/8 3/8-16 X 1/ 3/ /8 1-3/8-5/16 5-1/ /8 3/4-1/ -7/16 5-5/8 3-1/4-1/ 1-3/4 1-1/4 5/8-5/8 1/-13 X 3/4 1/ 1-3/8 1-5/8 1-3/4-11/16 5-7/ /8 3/4-1/ -7/16 5-5/8 4-1/ 1-3/4 1-1/4 5/8-5/8 1/-13 X 3/4 1/ 1-3/8 1-5/8 1-3/4-11/16 5-7/ /8 3/4-1/ -7/16 5-7/8 5-3/4 1-3/4 1-1/4 5/8-7/8 5/8-11 X 15/16 1/ 1-3/8 1-5/8 1-3/4-11/16 6-1/8 1-3/8 1-5/8 7/8-7/8-13/16 6-5/ / 3/4 3-1/8 3/4-10 X 1-1/8 3/4 1-3/4 1-1/8 3-1/8 3-1/16 6-7/8 END CAP DIMENSIONS BORE E TN TH RT R 1-1/ 5/8 1 1/4-8 X 5/16 1-7/16-1/ 7/8 1-1/4 5/16-4 X 3/8 1-7/3-1/ 3 1-1/4 1-1/ 5/16-4 X 7/16-3/16 3-1/4 3-3/4 1-1/ 1-7/8 3/8-4 X 1-49/ / -1/16-1/4 3/8-4 X 1 3-1/ / -11/16-3/4 1/-0 X 9/16 4-7/ / 3-1/4 3-1/4 1/-0 X 9/16 4-7/8 RT E TN NT R M8 Connector

8 Page 7 How to Order SPECIFIC INFORMATION CODE NA D4 SL15 RA1 V1 Options Maximum SERIES insight SERIES ANALOG CYLINDER NA Stroke in. 1 3/4" BORE - 3/4" ROD RA1 STANDARD D4 15 Analog Reporting " BORE - 3/4" ROD RA1 STANDARD D30 15 NAD 1/" BORE - 3/4" ROD RA1 STANDARD D49 18 (NON-NFPA) 3" BORE - 3/4" ROD RA1 STANDARD D70 4 Tie-Rod 3 1/" BORE - 1" ROD RA1 STANDARD D /" BORE - 1" ROD RA1 STANDARD D STROKE SPECIFY STROKE LENGTH IN DECIMALS SL FULL MALE THREAD (Standard) RA1 ROD END REDUCED MALE THREAD RA FEMALE THREAD RA3 SPECIFIC INFORMATION CODE NA K150 SL15 RA V1 Options SERIES insight SERIES ANALOG CYLINDER NA NAK (NFPA) Tie-rod STANDARD ROD NAK (NFPA) Tie-rod OVERSIZED ROD 1 1/" BORE - 5/8" ROD RA STANDARD K " BORE - 5/8" ROD RA STANDARD K /" BORE - 5/8" ROD RA STANDARD K /4" BORE - 1" ROD RA STANDARD K30 4 4" BORE - 1" ROD RA STANDARD K " BORE - 1" ROD RA STANDARD K " BORE - 1 3/8" ROD RA STANDARD K /" BORE - 1" ROD RA STANDARD K15 15 " BORE - 1" ROD RA STANDARD K0 15 1/" BORE - 1" ROD RA STANDARD K /4" BORE - 1 3/8" ROD RA STANDARD K3 4 4" BORE - 1 3/8" ROD RA STANDARD K " BORE - 1 3/8" ROD RA STANDARD K " BORE - 1 3/4" ROD RA STANDARD K60 48 STROKE SPECIFY STROKE LENGTH IN DECIMALS SL ROD END Signal Output Common Options for NAD and NSK NSK (NFPA) Specific Options FULL MALE THREAD REDUCED MALE THREAD (Standard) RA1 RA FEMALE THREAD RA VDC Increase with rod extension V VDC Decrease with rod extension V CUSTOM VDC OUTPUT V3 4-0 ma Increase with rod extension A1 0-4 ma Decrease with rod extension A CUSTOM ma OUTPUT STAINLESS STEEL ROD REAR (CAP) CLEVIS DETACHABLE EYE BRACKET ROD CLEVIS CLEVIS PIN AND RETAINERS FRONT FLANGE REAR FLANGE METALLIC ROD WIPER ROD MODIFICATION (DRAWING PREFERRED) SIDE END ANGLE MOUTNING FRONT TRUNION ROD EYE insight ANALOG REPORTING "NAD" SERIES (NON-NFPA) ORDERING INFORMATION "NAK" SERIES (NFPA) ORDERING INFORMATION CLEVIS PIN AND RETAINERS ALL TIE RODS EXTENDED (X1) REAR TIE RODS EXTENDED (X) FRONT TIE RODS EXTENDED (X3) A3 SS MG MH MF MZ MJ MK MW RM MS1 MT1 MX MZ MN MO MP TIE RODS EACH END EXTENDED (X4) MR Maximum Stroke in.

9 Page 8 PPC Programmable Position Cylinder An Industry First: A repairable tie-rod air cylinder with embedded electronics providing two discrete user programmable stop points. This cylinder design features both NFPA and Non-NFPA configurations. Time to throw your reed switches out! PROGRAMMABLE ELECTRONICS The insight Series Cylinder is a new design featuring embedded electronics, external keypad and wired outputs for a pneumatic cylinder. Precise repeatable position is easily programmed with the use of the external keypad. See illustration below right. Position sensing is accomplished using a new patented technology called: QVLA. This technology is LED light based and measures interior light intensity changes within a cylinder. As the piston moves the volume between the end cap and the piston varies. QVLA technology illuminates and measures this contained volume. The brighter the light, the less the rod extension. The dimmer the light the greater the rod extension. The patented emitting LED has a life estimated in decades and is self regulating providing constant illumination regardless of operating temperature or age. ELECTRONIC FEATURES AND SPECIFICATIONS FAST 4 KHz (Speed up your process) Non-Contact Weld Field Immune Cylinder Life > 5 Million Cycles LED life over 50 years Steel Tubes Available Non-Lubrication Operation Repeatability.030 inch Temperature Compensated Infinte Resolution OUTPUTS INPUTS NC Outputs Supply Voltage 1-4 volts Reverse Logic NC becomes NO Supply current ~ 50mA ESD Protected Isolation = 1500 VRMS M8 6-pin Female Connector Standard Switching Voltage 100 VDC Easy Set-up and calibration Switching Current 150 ma No Tools Required MECHANICAL DESIGN FEATURES Piston Rod Chrome Plated Steel Anodized Tubing Non-Lubrication Steel and Composite Tubes Available Machined Solid Aluminum End Caps Low Friction Cap Seals Non-Lubrication Low Stiction Clean Dry Air (0.3 micron fine grade coalescing filter with 5 micron pre-filter 135 PSI Max Operating Temperature -0 to 160 F One Year W arranty Actual keypad size Set-up Instructions 1) Press and Hold for seconds the yellow button corresponding to the position desired, either: Extend or Retract. ) When the corresponding orange LED blinks, physically set rod at desired position. 3) To finish, depress the blue SET button. Complete!

10 Page 9 Programmable NSD insight NSD FM RA1 NPT ROD DIA. MODEL A D C P Y SN XT ZB CC EE MM NSD1 1 5/16 5/8 1-3/3-1/3 1-1/ /3 3/8-16 1/8 3/8 NSD4 1-1/ 5/8 3/4-3/8 1-15/3 3-39/ /3 5-35/64 3/4-10 1/4 3/4 NSD30 1-1/ 5/8 3/4-3/8 1-15/3 3-39/ /3 5-35/64 3/4-10 1/4 3/4 NSD49 1-1/ 5/8 3/4-7/16 1-7/ / /3 5-35/64 3/4-10 3/8 3/4 NSD70 1-1/ 5/8 3/4-13/3 1-7/ / /3 5-35/64 3/4-10 3/8 3/4 insight NSD MODEL E TN BC RT R NT NSD1 1-13/16 ø /4-8X3/ /4-8X1/4 NSD4-3/8 5/3.49 5/16-4X9/ /16-4X9/3 NSD30-3/8 5/3.65 1/4-8X3/ /16-4X9/3 NSD49-7/8 1-1/ /16-4X9/ /16-4X1/ NSD70 3-3/8 1-1/ /16-4X9/ /16-4X9/16 Side Tapped Mount Dimensions NSD1 ONLY

11 NFPA Page 10 NSK Programmable BORE 1-1/ -1/ 3 1/4 ROD DIA. NPTF EE insight NSK CYLINDER DIMENSIONS P F SN NT A W Y XT ZB 5/8 1/4 3/4 5/8 1-3/4 1-15/16 4-5/8-1/8 3/8-1/4 1/4-0 X 17/64 1 1/4 1-1/8 1-1/8-5/16 5 5/8 1/4 3/4 5/8 1-3/4 1-15/16 4-5/8-1/8 3/8-1/4 5/16-18 X 3/8 1 1/4 1-1/8 1-1/8-5/16 5 5/8 1/4 3/4 5/8 1-3/4 1-15/16 4-3/4-1/4 3/8-3/8 3/8-16 X 1/ 1 1/4 1-1/8 1-1/8-5/16 5-1/8 1 3/8 1-1/8 3/4-1/4-7/16 5-5/8-1/ 5/8-5/8 1/-13 x 3/4 1-3/8 3/8 1-5/8 1-1/ -11/16 5-7/8 insight NSK END CAP DIMENSIONS BORE E TN RT R 1-1/ 5/8 1/4-8 X 5/16 1-7/16-1/ 7/8 5/16-4 X 3/8 1-7/3-1/ 3 1-1/4 5/16-4 X 7/16-3/16 3-1/4 3-3/4 1-1/ 5/16-4 X 7/16-49/64

12 Page 11 Programmable SPECIFIC INFORMATION CODE NS D4 SL15 RA Options SERIES insight SERIES PPC CYLINDER NS 1 1/4" BORE - 3/8" ROD RA1 STANDARD D /4" BORE - 3/4" ROD RA1 STANDARD D4 15 NON-NFPA " BORE - 3/4" ROD RA1 STANDARD D30 0 1/" BORE - 3/4" ROD RA1 STANDARD D49 4 3" BORE - 3/4" ROD RA1 STANDARD D70 4 STROKE SPECIFY STROKE LENGTH IN DECIMALS SL ROD END Options FULL MALE THREAD REDUCED MALE THREAD FEMALE THREAD STAINLESS STEEL ROD REAR (CAP) CLEVIS DETACHABLE EYE BRACKET ROD CLEVIS CLEVIS PIN AND RETAINERS FRONT FLANGE REAR FLANGE METALLIC ROD WIPER ROD MODIFICATION (DRAWING PREFERRED) SPECIFIC INFORMATION CODE NS K150 SL15 RA Options RA1 RA RA3 SERIES insight SERIES PPC CYLINDER NS STANDARD ROD OVERSIZED ROD 1 1/" BORE - 5/8" ROD RA STANDARD K " BORE - 5/8" ROD RA STANDARD K00 0 1/" BORE - 5/8" ROD RA STANDARD K /4" BORE - 1" ROD RA STANDARD K /" BORE - 1" ROD RA STANDARD K15 15 " BORE - 1" ROD RA STANDARD K0 15 1/" BORE - 1" ROD RA STANDARD K /4" BORE - 1 3/8" ROD RA STANDARD K3 4 STROKE SPECIFY STROKE LENGTH IN DECIMALS SL ROD END Options FULL MALE THREAD REDUCED MALE THREAD FEMALE THREAD STAINLESS STEEL ROD REAR (CAP) CLEVIS DETACHABLE EYE BRACKET ROD CLEVIS CLEVIS PIN AND RETAINERS FRONT FLANGE REAR FLANGE KEYPAD ON CYLINDER "NSD" SERIES (NON-NFPA) ORDERING INFORMATION SS MG MH MF MZ MJ MK MW "NSK" SERIES (NFPA) ORDERING INFORMATION METALLIC ROD WIPER ROD MODIFICATION (DRAWING PREFERRED) RM RA1 RA RA3 SS MG MH MF MZ MJ MK MW RM Maximum Stroke in. Maximum Stroke in.

13 Page 1 Rod Clevis and Pin (Code MF) NAD & NSD Mounting ROD CLEVIS & PIN (Code: MF) CC MODEL PART NO. A CB CD CE CG CW ER L (FM) / 5/8-5/64 9/16 5/16 51/64 7/3 3/ / 3/4-1/64 3/4 1/ 1-1/16 1-1/3 1-8 Flange Mount FLANGE MOUNT (Code: MJ (front) MK (rear) ) MODEL PART NO. E F R ES FB RF UF /3 7/ /4 5/16 3-1/3 3-19/ /3 7/ /4 5/16 3-1/3 3-19/ /16 7/ /4 5/16 3 7/ /8 7/ /4 5/ /3 4 1/ /4 5/ / 5-1/ / /64 5/ / 6-1/16 7 Optional Rod Ends OPTIONAL ROD ENDS SM RA & SF RA3 ROD A** C** CC BORE DIA. AD CD AF (FM) KK 1-3/4 3/4 1-1/ 3/4 3/4 3/4-10 1/-13 3/4 1-1/ 3/4 3/4 3/4-10 1/-13-1/ 3/4 1-1/ 3/4 3/4 3/4-10 1/ /4 1-1/ 3/4 3/4 3/4-10 1/ / 1 1-5/ / / / 1 1-5/ / /4-10

14 Page 13 NAD & NSD Mounting Clevis Bracket and Pin (Code MG) CLEVIS BRACKET & PIN (Code: MG) MODEL PART NO. E F FL R CW CB CD DD LR MR /8 3/8 1-3/ /3 1/ 1/ 5/16 7/8 5/ /8 3/8 1-3/ /3 1/ 1/ 1/4 7/8 5/ /8 3/8 1-1/.06 3/8 1/ 5/8 5/16 1-1/16 13/ /8 3/8-1/8.65 3/8 1/ 5/8 5/ /16 13/ /8 3/8-1/ /8 1/ 3/4 1/ 1-1/ /8 3/8-3/ /8 1/ 3/4 1/ 1-1/ 1-3/8 Eye Bracket (Code MH) Note: Eye bracket not available on the NAD-70 use eye bracket from NAD-49, part number 701. EYE BRACKET (Code: MH) MODEL PART NO. E F FL R CD DD EW LR MR /8 3/8 1-7/ / 5/16 1/ 7/8 5/ /8 3/8 1-7/ / 5/16 1/ 7/8 5/ /8 3/8-1/8.06 5/8 5/16 1/ 1-1/16 13/ /8 3/ /4 1/ 1/ 1-1/ /8 3/8 3-1/ /4 1/ 1/ 1-1/ 1-3/8

15 NFPA Page 14 MS1 Mount (Code MI) NSK & NAK Mounting SINGLE END ANGLE MOUNTING MS1 (Code: MI) BORE AB S AH AL AO AT SA XA ZA ** 5-5/ / 7/16 1-1/4 1-3/16 1 3/8 1/8 6 7/ /8 5-5/8 6 7/16 1-3/4 1-7/16 1 3/8 1/8 6 7/ /8 5-3/4 6-1/8-1/ 7/16-1/4 1-5/8 1 3/8 1/8 6-1/8 7/8 6-1/8 6-1/ 6-7/8 7-3/8 3-1/4 9/16-3/4 1-15/16 1-1/4 1/ 1/8 7-3/8 1-1/8 7-1/8 7-5/8 6-7/8 7-3/8 4 9/16 3-1/ -1/4 1-1/4 1/ 1/8 7-3/8 1-1/8 7-1/8 7-5/8 7-1/4 7-7/8 5 11/16 4-1/4-3/4 1-3/8 5/8 3/16 7-7/8 1-1/8 7-1/ 8-1/ /8 6 13/16 5-1/4 3-1/4 1-3/8 5/8 3/16 8-1/ 1-1/4 8-1/4 8-7/8 Conforms to NFPA Type MS1 mount cylinders. Also available as a separate modular mounting kit, complete with two angle brackets, two short screws for attachment to cap end, two long screws and bushing for attachment to head end. MT1 Front (Code MA) TRUNNION MOUNTING TD BORE TC TL UT XG XJ ± / / / -1/ /4 3-3/ / / / / / 7-1/ 1-3/8 9-1/4 1-3/4 4-1/8-1/8 4-1/ 1-3/4 4-1/8-1/8 4-1/ 1-3/4 4-1/8-1/8 4-1/ -1/4 5-1/ 5-1/4-1/4 5-1/ 5-1/4-1/4 5-1/ 5-1/4-5/8 5-7/8-7/8 6-1/8

16 Page 15 NFPA NSK & NAK Mounting Clevis Bracket (Code MG) MP ADDERS: Add 3/8 inch for 1-1/,,-1/ bore. Add 5/8 inch for 3-1/4, bore. Conforms to NFPA Type MP1 & MP mount cylinders. Also available as a separate modular mounting kit, complete with clevis bracket, four mounting screws, pin and two snap-rings. FIXED CLEVIS MOUNTING MP1 (Code: MG) ROD CD BORE DIA. L* M CB ±.001 CW XC* ZC* 1-1/ -1/ 3-1/ /8 5-3/8 5-7/8 3/4 1/ 3/ / 1 5-3/4 6-1/4 5/8 5-3/8 5-7/8 3/4 1/ 3/ / 1 5-3/4 6-1/4 5/8 5-1/ 6 3/4 1/ 3/ / 1 5-7/8 6-3/ /8 7-5/8 1-1/4 3/4 1-1/ /8 1 3/8 7-1/8 7-7/ /8 7-5/8 1-1/4 3/4 1-1/ /8 1 3/8 7-1/8 7-7/ /8 7-7/8 1-1/4 3/4 1-1/ /8 1 3/8 7-3/8 8-1/8 1 3/8 8-1/8 9-1/8 1-1/ 1 1-1/ /4 1 3/4 8-3/8 9-3/8 Front Flange Mount MF1 (Code MJ) Rear Flange Mount MF (Code MK) Conforms to NFPA Type MF1 or MF mount cylinders. Also available as a separate modular mounting kit, complete with flange and four mounting screws to attach to head end for MF1 front flange mount or cap end for MF mount. FLANGE MOUNTING BORE E F R W FB TF UF ZF 1-1/ -1/ 3-1/ / 3 3-3/4 4-1/ 5-1/ 6-1/ 3/8 3/8 3/8 5/8 5/8 5/8 3/4 1-7/16 1-7/3-3/16-49/64 3-1/64 4-7/64 4-7/8 5/8 5 5/16-3/4 3-3/ /8 5/8 5 3/8 3-3/8 4-1/ /8 5/8 5-1/8 3/8 3-7/8 4-5/ / 3/4 6-1/4 7/ /16 5-1/ 1 6-1/ 3/4 6-1/4 7/16 5-7/16 6-1/ / 3/4 6-1/ 9/16 6-5/8 7-5/ /4 7/8 7-3/8 9/16 7-5/8 8-5/8 1-1/8 7-5/8

17 NFPA Page 16 Extended Tie-Rod (Codes MN, MO, MP, MR) NSK & NAK Mounting EXTENDED TIE ROD MOUNTING BORE W AA BB DD ZJ K F 1-1/ 5/ / /8 7/3 3/8 5/ /8 5/ /8 17/64 3/8-1/ 5/ /8 5/ /4 3-1/4 3/ /8 3/ /8 17/64 3/8 1/64 5/8 Conforms to NFPA Extended Tie-Rod mount. Also available as a separate modular mounting kit with four tie rod extension studs. Two kits should be ordered for X1 mounting. X1 - All extended (CODE MN) X - Rear extended (CODE MO) X3 - Front extended (CODE MP) X4 - Two each end extended (CODE MR) 4 3/ /8 3/ /8 1/64 5/8 5 3/ /16 1/-0 5-7/8 _ 5/8 6 7/ /16 1/-0 6-5/8 _ 3/4 Eye Bracket (Code MH) (NOT MP4) Pin (Code MZ) ACCESSORY DIMENSIONS CYLINDER ROD BORE DIA. A F M CA CB CD CE CF CG CL CW DD ER FL 1-1/,,-1/ 5/8 3/4 3/8 1/ 1-1/ 3/4 1/ 1-1/ 1-5/8-1/ 1-3/4 1/ 3/8 9/16 1-1/8 3-1/4, 4, /8 5/8 3/4-1/16 1-1/4 3/4-3/8-35/64 3-1/ -1/ 5/8 1/ 13/16 1-7/ /8 1-5/8 3/4 1-13/16 1-1/ 1 3-1/8 3-1/4 4-1/ 3 3/4 5/8 1-3/3-1/4 ACCESSORY DIMENSIONS KK(SF) ROD & EYE ROD ROD CYLINDER ROD EYE BRACKET EYE CLEVIS PIN BORE DIA. THREAD P/N P/N P/N P/N 1-1/,,-1/ 5/8 7/ /4, 4, 5 1 3/ /

18 Page 17 NFPA NSK & NAK Mounting Rod Clevis (Code MF) Rod Clevis available only in KK (SF) threading shown. Select Style (SM) rod thread to match. Rod Eye (Code MX) Rod eye available only in KK (SF) threading shown. Select Style (SM) rod thread to match. Optional Rod Ends FULL MALE (FM) Code: RA1 SMALL MALE (SM) Code: RA SHORT FEMALE (SF) Code: RA3 ROD ENDS ROD ROD A DIAM. DIA. AD C CC KK BORE MM CODE AF B CD D (FM) (SM & SF) 1-1/ 5/8 5/ /4 3/ /8 3/8 1/ 1/ 5/8-18 5/8-18 7/16-0 7/ /8 1-1/ / 1/ 7/8 7/ /4-16 3/4-16 5/8 1 3/ /8 1/ 5/8-18 7/ / 1 1-1/ / 7/ / / / 7/ / /4 1-3/8 1-5/ /8 1-1/8 1 3/ / / 7/ / /8 1-5/ /8 1-1/8 1 3/ / /8 1-5/ / 5/8 7/8 1-1/ /8-1 3/ /8 1-3/4 1-5/ /8 3/4 1-1/8 1-1/ 1 3/ / /4-1

19 Page 18 Discussion What is QVLA? QVLA is a patented sensing technology. It is based on light intensity to measure volumes. Different or changing light intensities within a dynamic volume indicate volume changes. Light flooding the interior of a chamber is reflected and absorbed differently as the volume changes shape or size. With an LED mounted in the end cap, light intensity changes as the piston moves. We interpret the light intensity into rod position. One of the greatest strengths of QVLA is direct measurement of your work piece s position. There are no transducers or potentiometers, no mechanical connections that could affect the accuracy of the measurement, and no external switches subject to misreads, damage, or failure. With QVLA, you can be assured your work piece is where it is supposed to be. Piston position defines the internal volume between the rear cap and itself. With our special electronics we interpret light intensity of this volume into rod position. Low light levels with larger volume. Higher light levels with smaller volume. Special patented QVLA emitter. Your Control Electronics

20 Page 19 Electronic Connections M8 Nano Connector 3 1)+1-4vdc (Brown) ) Signal (BLK) 3) Ground (Blue) 1 Proportional Control This combination of QVLA position reporting technology incorporated into our air cylinder and Enfield S proportional air valve will result in exciting new possibilities for accurate, repeatable position sensing and control otherwise not obtainable with currently available sensing systems. Software available for quick easy set up of Enfield valve available on their web site: AIR PLC AIR IN MAX 135 PSI Inlet air should be dry (-40F dew point) non-lubricated air, non-flammable & non-corrosive dry gases (0.3micron fine grade coalescing filter with 5 micron pre-filter) at 0-135psig Electrical and pneumatic connections between Motion Controls Analog Reporting Cylinder (ARC) and Enfield Technologies S-05-U-04 Valve. BLUE GROUND BROWN +4VDC BLACK COMMAND FEEDBACK WARNING: Installation and operation of electronic and high pressure systems (fluids and compressed gas) involves risk including property damage and personal injury or death. Users should be properly trained or certified and take safety precautions.

21 Page 0 50 Years of Cylinders! Thank you for your business, we enjoy making product for your needs. Made in Wisconsin. Motion Controls LLC 1174 Western Dr, Hartford, WI All rights reserved. 015