Part Number: N006EN

Size: px
Start display at page:

Download "Part Number: N006EN"

Transcription

1

2 Revision Control Revision Rev. A Important Notices Part Number: N006EN Publication Date October , Utilimastet.B> Printed in u.s.a. Title: Upgrading RIMHood Stops-Body Information Bulletin Utilimaster attempts to provide information that is accurate, complete, and useful. All information contained in this document is based on the latest product information available at the time ofpublication. However, because ofthe Utilimaster policy ofcontinual product improvement, Utilimaster reserves the right to amend the information in this document at any time without prior notice. For more assistance, contact: Utilimaster Corporation Attention: Customer Service State Road 19, P.O. Box 585 Wakarusa, IN , U.S.A ( ), Fax Introduction SITUATION: If you fmd excessive wear on the front bottom RIM hood stops ofan Aeromaster van, you may retrofit the four rubber hood stops with two larger hood stops. AFFECTED UNITS: Vehicles with RIM hoods. CORRECTION: Remove old hood stops, install new ones, and adjust the hood alignment. See Section 5.0 for complete procedure-read all the instructions before beginning the procedure. TO ORDER PARTS: See Section 3.0 for complete ordering instructions. 2.0 Tools and Parts 2.1 Parts (1) Kit RIM Hood Bumper Stops 2.5 OD (PIN SK) which includes: (4) Washer 5116 Flat (PIN ) (2) Nut Lock Wx WayFlange Gr 5 Zinc (PIN ) (2) Bolt Hex x 1-1/4" Gr 8 Zinc (PIN ) (2) Spacer Steel.34 ID x.40 OD x 1.5" Zinc (PIN ) (2) Rubber Bumper 2.50 Diameter x 1.00 (PIN ) 2 Upgrading RIM Hood Stops

3 2.2 Tools (2) Self-tapping Pan-head Torx Screw 1/4-20 x 3/4" (PIN 1l300177) (4) Washer #10 (PIN ) (4) Bolt (Machine Screw) Stainless Steel #10-24 x 3/4" (PIN ) (4) Nut Lock Stainless Steel #10-24 (PIN ) (4) Nut Lock Wxd 5/ Way Or 5 Zinc (PIN ) Safety glasses Drill with 5116" bit Phillips screwdriver (or screw gtm with Phillips bit) Torx screwdriver (or screw gun with TorX bit) Standard box and open end wrench set Standard socket set Torque wrench with ft lb increments 3.0 Ordering Parts To order the kit for this vehicle, gather the following information: Model and year of vehicle. Chassis VIN or Utilimaster Body Serial Number. Mileage at time of failure. Complete shipping address. Description ofthe necessary parts (RIM Hood Bumper Stops Repair Kit 2.5 OD, PIN SK). Then contact Utilimaster Customer Service by one ofthe following methods: Call (or ) and ask for a Parts Department representative. Fax your order with the above information to yourorderwiththeaboveinformationtoCustSvc@Utilimaster.com. Mail or express service to the following address: Utilimaster Corporation Attn: Parts Department State Road 19 P.O. Box 585 Wakarusa, IN NOTE: See the service page ofthe Utilimaster web site ( complete information about finding VIN and body serial numbers, ordering parts, and filing warranty claims. NOTE: When phoning Utilimaster, be aware that our 219 telephone area code is changing to 574 in January The 800 numbers will be unaffected. Body Information Bulletin 3

4 4.0 Safety Cons iderations The following list contains general WARMNGS that you should follow when you service a vehicle. Always wear safety glasses for eye protection. Be sure that the ignition switch is always in the OFF position and the parking brake is set. Do not smoke while working on the vehicle. To avoid injury, always remove rings, watches, loose-hangingjewelry, and loose clothing before beginning to work on a vehicle. Keep yourself and clothing away from moving pru.ts. Tie long hair securely behind your head. Some electric fans may engage even when the engine is not running. 5.0 Procedure NOTE: Read all instructions before starting. 1. Release the hood hold-down straps, open the hood, and secure the hold-open device. Illustration 5-1 Existing Configuration 4 Upgrading RIM Hood Stops

5 2. Remove the four rubber hood stops. (See illustration 5-1 and 5-2.) 3. Ifthere is a set screw, it needs to be removed. (See Illustration 5-1.) 4. Loosen both mount brackets. (See Illustration 5-3.) 5. Directly below each hood strap catch, locate the center ofthe hood support (9/16" from the back edge ofthe hood support). (See Illustration5-4.) 6. Using a 5/16" bit, drill two holes through the bottom ofthe hood support. (See Illustration 5-5.) Illustration 5-2 Remove Existing Hood Stops Illustration 5-3 Loosen Mount Brackets Illustration 5-4 Center with Strap Catch Illustration 5-5 Drill Holes Body Information Bulletin 5

6 7. Attach one 2-112" rubber bumper (PIN ) to the hood support with two washers (PIN ), a spacer (PIN ), a x 1-1/4" bolt (PIN ), and a flange locknut (PIN ). (See illustrations 5-6 and 5-7.) For each hood stop, the spacer goes through the bumper, washers are on both sides ofthe bumper, the bolt goes through the spacer, and (after inserting the bolt through the hood support) the locknut goes on the end ofthe bolt. Repeat for the other side. 8. Torque the nuts to 5-7 ft-l b. 9. Remove the two bolts holding each moill1t to the bumper, and discard the locknuts. (See illustration 5-7.) Illustration 5-6 Attach Replacement Bumpers Hex Bolt Locknut Washer Washer Hood Stop (Rubber Bumper) _ r i Set Screw \ ---Strap...r---""Bolts, Nuts, & Washers lllustration 5-7 Hood Stop in Place 6 Upgrading RIM Hood Stops

7 10. Place each mmmt in a vice and drill out the rivets attaching the hold-down strap to the mount. 11. Reverse the hold-down strap so that the rubber knob faces away from the grill. (Compare Illustration 5-1 with 5-7.) 12. Reattach the hold-down strap to each mount with the stainless steel x 3/4" bolt (PIN ), washer (PIN ), and nut (PI N ). 13. Reattach the molmts to the bumper, using new locknuts (PIN ). Torque the 5/16" locknutsto ft lb. 14. Adjust the mount supports so that the stops are flat against the top surface and so that there is also an equal spacing in the gap between the quarter panel and the fender. (See Illustration 5 7 through 5-10.) Pushing the mount up or down along the vertical slot adjusts the gap between the quarter panel and the fender (pushing the molmt up increases the gap at the bottom). Pushing the mount sideways along the horizontal slots adjusts the alignment ofthe molmt and the hood stop. 15. Secure the location after all adjustments have been made by drilling a new 7/32" (.218") hole behind the adjustrnent slot and securing with the self-tapping pan-head Torx screw (PIN ). This will act as aset screw. (See lllustration 5-7.) Illustration 5-8 Poor Alignment Illustration 5-9 Good Alignment Illustration 5-10 Proper Hood and Quarter Panel Gap Body Information Bulletin 7

RIM Hood For Aeromaster Bodies

RIM Hood For Aeromaster Bodies RIM Hood For Aeromaster Bodies Service Guide WARNING: Hood should be opened by releasing the hold-down straps, lifting the hood, and engaging the prop rod. Be sure prop rod is properly engaged before working

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 2011 Dodge Charger Road Defender 5000 Series Push Bumper Part Number 5076 Do not attempt to install this product on any vehicle other than the one it is designed for and listed

More information

INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2009 CIVIC HYBRID All 40191 Issue Date AUG 2008 PARTS LIST Rear under spoiler 2 Step bolts 4 Self-tapping screws TOOLS REQUIRED Phillips

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 33322-36889 UNDER 2007 TL Issue Date MAY 2007 PARTS LIST Front under spoiler Left bracket (Marked L ) Right bracket (Marked R ) 8 Self-tapping

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory P/N 08U89-TK6-111 Application 2012 FIT Publications No. AII 45981 Issue Date AUG 2011 PARTS LIST Armrest console Armrest cover Bolt cover Floor bracket Washer bolt,

More information

P-Series Installation

P-Series Installation Utilimaster Access System Introduction P-Series Installation This information describes installation of the Utilimaster Access System (UAS) P-Series (one-button FOB) designed to replace the existing ACE

More information

Van Rack Installation Manual Ford Transit Connect

Van Rack Installation Manual Ford Transit Connect 1.888.772.8400 Big to small... We do it all Van Rack Installation Manual Ford Transit Connect Thank you for your purchase of an Unruh Fab Van rack. We have designed and built this rack so that you can

More information

Parts Manual for LAWN TRACTORS MANUAL CLUTCH HYDRO DRIVE SERIES F MODELS LT145H33FBV LT145H38FBV ELT145H33FBV

Parts Manual for LAWN TRACTORS MANUAL CLUTCH HYDRO DRIVE SERIES F MODELS LT145H33FBV LT145H38FBV ELT145H33FBV Parts Manual for LAWN TRACTORS MANUAL CLUTCH HYDRO DRIVE SERIES F MODELS LT145H33FBV LT145H38FBV ELT145H33FBV IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO

More information

Can-Am Spyder RT One-piece Seat and Passenger Backrest

Can-Am Spyder RT One-piece Seat and Passenger Backrest Can-Am Spyder RT 2010-2018 One-piece Seat and Passenger Backrest Hardware: Tools needed: Seat: Stock rear mounting bolts and box nuts ¼ 20 x 5 / 8 " Phillips screws x 2 (included) Metric hex wrenches (seat)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publication No. INSTALLATION INSTRUCTIONS 2 PIECE FOLDING POLY WINDSCREEN (OPTICAL) P/N 0SR72-HL3-100 SXS700M4/M2 Honda Dealer: Please give a copy of these instructions to your customer.

More information

LAWN TRACTORS MANUAL CLUTCH HYDRO DRIVE SERIES "G"

LAWN TRACTORS MANUAL CLUTCH HYDRO DRIVE SERIES G Parts Manual for LAWN TRACTORS MANUAL CLUTCH HYDRO DRIVE SERIES "G" MODEL ELT145H33GBV LT145H33GBV LT145H38GBV LT150H38GKV WLT145H38GKV McDonough, GA, 30253 U.S.A. COPYRIGHT 2006 SNAPPER PRODUCTS, INC.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. UNDER 2007 CIVIC SI All 33529 Issue Date AUG 2006 PARTS LIST Rear under spoiler Clip Rubber washer 6 Flange bolts 6 Flange nuts TOOLS REQUIRED

More information

ELECTRIC START KIT KIT P/N

ELECTRIC START KIT KIT P/N ELECTRIC START KIT KIT P/N 2873876 Application 2002 Polaris EDGE Models with 500-600 Domestic Engines Before you begin, read these instructions and check to be sure all parts and tools are accounted for.

More information

PARTS LIST. Reproduction. Not for. Mower Decks. Mfg. No. Description EZM2042, 20HP B&S w/42" Mower Deck (2009)

PARTS LIST. Reproduction. Not for. Mower Decks. Mfg. No. Description EZM2042, 20HP B&S w/42 Mower Deck (2009) PARTS LIST Mower Decks Mfg. No. Description 7800490 EZM2042, 20HP B&S w/42" Mower Deck (2009) Manual Part No. Revision A Rev. Date: 11/5/2009 Table Of Contents PRODUCT COMPONENTS PAGES Frame, Body & Seat

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory Application Publication No. INSTALLATION INSTRUCTIONS WINCH MOUNT KIT P/N 08L77-HL3-A00 SXS700M4/M2 Honda Dealer: Please give a copy of these instructions to your customer. MII 14607 Issue Date

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece

More information

PRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Left front trim piece

PRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Left front trim piece INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece

More information

INSTALLATION INSTRUCTIONS C-DMM FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT

INSTALLATION INSTRUCTIONS C-DMM FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT INSTALLATION INSTRUCTIONS C-DMM-123 2013-2018 FORD INTERCEPTOR UTILITY SWING-OUT DASH MONITOR MOUNT The Dash Monitor Mount bracket system requires two or three main parts that are sold separately. See

More information

INSTALLATION INSTRUCTIONS DRAWERS #240

INSTALLATION INSTRUCTIONS DRAWERS #240 INSTALLATION INSTRUCTIONS DRAWERS #240 Please read and fill out the enclosed warranty registration card to activate your warranty. SHIPMENT CONTENTS #1 Lid #2 Rear #3 Left side panel #4 Right side panel

More information

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD / HDX WINCH MOUNT GRILLE GUARD / MAX WINCH MOUNTING SYSTEM APPLICATION: 2016 Chevrolet Silverado 1500 PART NUMBER: 40-93875,

More information

POLY TIP-DOWN WINDSHIELD KIT

POLY TIP-DOWN WINDSHIELD KIT POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please

More information

K9-F17 INSTALLATION INSTRUCTIONS K9 Kit for FORD INTERCEPTOR SEDAN

K9-F17 INSTALLATION INSTRUCTIONS K9 Kit for FORD INTERCEPTOR SEDAN K9-F17 INSTALLATION INSTRUCTIONS K9 Kit for 2013-2018 FORD INTERCEPTOR SEDAN TOOLS Needed: Phillips Screw Driver Trim panel removal tools Caulk Gun Standard Socket set Metric Socket set Wire Cutters /Crimpers

More information

LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions

LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and

More information

Cab Kit Installation Instructions

Cab Kit Installation Instructions Low Speed Vehicles (LSV) Electric Vehicles: Carryall Carryall 6 Cab Kit Installation Instructions Publication 050770 These instructions apply to the following kit: 0670 Edition Code 008E09D GENERAL INFORMATION

More information

MGB Alternator Conversion Installation Instructions For MGA & 1962 to 1967 MGB

MGB Alternator Conversion Installation Instructions For MGA & 1962 to 1967 MGB MGB Alternator Conversion Installation Instructions For MGA & 1962 to 1967 MGB PART# 130-078, 130-088, 130-098 440 Rutherford St. Goleta, CA 93117 1-800-642-8295 FAX 805-692-2525 www.mossmotors.com Scan

More information

Rear bumper cannot be used for towing after installation of the rear bumper relocation brackets.

Rear bumper cannot be used for towing after installation of the rear bumper relocation brackets. 921RC7030 GM 88-98 4WD 1500 P/U 3 Body Lift Thank you for choosing Rough Country for all your suspension needs. *RC703BAG2* RC703BAG2 Rough Country recommends a certified technician install this kit. Attempts

More information

INSTRUCTIONS. INTERCOOLER UPGRADE BMW E82 135i 2008-

INSTRUCTIONS. INTERCOOLER UPGRADE BMW E82 135i 2008- INSTRUCTIONS INTERCOOLER UPGRADE BMW E82 135i 2008- Parts Included: - Intercooler - Left and right side pipes with hoses - 3 Silicone Hoses ( 2.5 x 3 ) - 1 Silicone Hose 90degree 2.5 elbow - 8 Hoseclamps

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26033 KIT 2004 ODYSSEY Issue Date JAN 2004 PARTS LIST Trailer Hitch: P/N 08L92-S0X-100 Heavy-Duty P/S Cooler Kit P/N 53765-S0X-305 Heavy-duty

More information

Please visit for the latest version of these installation instructions.

Please visit  for the latest version of these installation instructions. Please visit www.blueox.com for the latest version of these installation instructions. Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue

More information

Passenger/Right Top Support Bracket. (2) 10mm Nut Plates

Passenger/Right Top Support Bracket. (2) 10mm Nut Plates PARTS LIST: 1 Extreme Grille Guard 16 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 10 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 10 12mm Hex Nuts 1 Driver/Left

More information

Setting the World s Performance Standards

Setting the World s Performance Standards Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Forced Air Hot Air Elimination Kit (Bed Fan Kit) For 800 RZR-4 P/N 67-165 Kit Contents:

More information

Ref Qty Part Description Part Number -1- Kit ( ) Contents:

Ref Qty Part Description Part Number -1- Kit ( ) Contents: REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain

More information

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler

OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0921 APPLICATION 2007-08 E92 335i/xi without stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler

More information

FREEDOM3 Portable Restroom Assembly Instructions

FREEDOM3 Portable Restroom Assembly Instructions FREEDOM3 Portable Restroom Assembly Instructions PN 21337 REV M - 1-1-19-17 FREEDOM 3 ASSEMBLY INSTRUCTIONS PN 21337 REV M -2-1-19-17 PARTS LIST: PN 21337 REV M - 3-1-19-17 INTRODUCTION Satellite portable

More information

P/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or

P/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain

More information

Installation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD

Installation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD Installation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always recommend

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory P/N 08L92-TX4-200 Application 2013 RDX Publications No. BII 13467 Issue Date MAR 2012 PARTS LIST 4 Nuts, Trailer hitch 10 Plain washers, Ball mount 6 Spring washers,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory ENGINE BLOCK P/N 08T44-SWA-1A0 Application 2012 CIVIC 4-DOOR Si Publications No. AII 45627 Issue Date APRIL 2011 PARTS LIST Engine block heater Aluminum washer Heater

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)

More information

, Ford F-250/F-350, Single Rear Wheel Rear Mount Bracket with Mud Flap Mounting Diagram & Instructions GB759842

, Ford F-250/F-350, Single Rear Wheel Rear Mount Bracket with Mud Flap Mounting Diagram & Instructions GB759842 2017-2019, Ford F-250/F-350, Single Rear Wheel Rear Mount Bracket with Mud Flap Mounting Diagram & Instructions GB759842 IMPORTANT: The manufacturer is not responsible for negligent use of vehicle with

More information

GMC Yukon

GMC Yukon Torch Series LED Grille TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD / MAX WINCH TRAY HDX WINCH MOUNT GRILLE GUARD APPLICATION: 2017 Ford F250/350 Super Duty PART NUMBER: 40-93905, 45-93900,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory LOWER P/N 08P46-SZA-100A Application 2011 PILOT Publications No. AII 43325-45001 Issue Date SEP 2010 PARTS LIST Rear lower trim 2 Washer-nuts 2 Special bolts TOOLS AND

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2009-2018 Dodge Ram 1500 (Excl. Rebel Model) 2019 Dodge Ram 1500 Classic PART NUMBER: 32-1960, 32-1965, 32-1960L, 32-1965L

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S Application 2013 ACCORD 4-DOOR Publications No. AII 13026 Issue Date AUG 2012 PARTS LIST Aluminum tape Backup Sensors Attachment Kit P/N 08V67-T2A-100A Control unit

More information

LAWN TRACTORS ELECTRIC CLUTCH HYDRO DRIVE SERIES "G"

LAWN TRACTORS ELECTRIC CLUTCH HYDRO DRIVE SERIES G Parts Manual for LAWN TRACTORS ELECTRIC CLUTCH HYDRO DRIVE SERIES "G" MODEL LT160H42GBV LT160H42GBV2 LT180H48GBV2 WLT160H42GBV WLT180H48GBV2 McDonough, GA, 30253 U.S.A. COPYRIGHT 2006 SNAPPER PRODUCTS,

More information

Installation Instructions

Installation Instructions Installation Instructions HighRock 4x4 TM Rear and Tire Carrier Vehicle Application: 1986-2006 Jeep Wrangler and Wrangler Unlimited HighRock 4x4 TM Rear and Tire Carrier Part Number: 42931 / 44931 www.bestop.com

More information

Installation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with ECM controlled fan output)

Installation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with ECM controlled fan output) Installation Instructions for Lingenfelter 2007-2013 GM 2500 Suburban & Yukon XL Auxiliary Fan System (with ECM controlled fan output) PN L300090607 Revision - 1.1 Lingenfelter Performance Engineering

More information

Rev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION

Rev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION Rev. 04-10 QTY 3D PART NO. DESCRIPTION 1 691609 FRONT BUMPER REPLACEMENT 1 691610 RIGHT SIDE SKIRT 1 691611 LEFT SIDE SKIRT 1 691612 REAR LOWER SKIRT 4 3M 94 3M ADHESION PROMOTER 16 #8 X ¾ SELF DRILLING

More information

Hood Lift Kit Installation Instructions For Mazda Miata PART # , ,

Hood Lift Kit Installation Instructions For Mazda Miata PART # , , Tools required: Rivet gun, masking tape, small flat screw driver, 10mm combination wrench, two13mm combination wrenches, two 17mm combination wrenches. Read and understand these instructions before attempting

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory BACKUP S Application 2012 ODYSSEY Publications No. AII 46724 Issue Date SEP 2011 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-TK8-100A Right center sensor clip

More information

PRESENT, FORD TRANSIT, FRONT TOW POINT Version 1.0

PRESENT, FORD TRANSIT, FRONT TOW POINT Version 1.0 4039 2013-PRESENT, FORD TRANSIT, FRONT TOW POINT Version 1.0 General Notes For the most up to date and current instructions, please visit our website at www.vancompass.com Please read all instructions

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08L92-S0X-100 ODYSSEY AII 22049 Issue Date AUG 2000 PARTS LIST Trailer hitch Receiver cover 2 Small wire ties (1 not used) Ball mount

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. ATTACHMENT (EX-L WITH NAVI) 2008 RIDGELINE AII 36587 Issue Date MAY 2007 PARTS LIST Attachment Kit P/N: 08B21-SJC-102 Template Rear camera

More information

Installation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo

Installation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo Installation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always

More information

LAWN TRACTORS ELECTRIC CLUTCH HYDRO DRIVE SERIES F

LAWN TRACTORS ELECTRIC CLUTCH HYDRO DRIVE SERIES F Parts Manual for LAWN TRACTORS ELECTRIC CLUTCH HYDRO DRIVE SERIES F MODELS LT160H42FBV LT160H42FBV2 LT180H48FBV2 IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL

More information

Installation Instructions BX1641 Monte Carlo SS

Installation Instructions BX1641 Monte Carlo SS Installation Instructions BX1641 Monte Carlo SS 2000-03 Serial No. The front bumper and headlights are removed for baseplate installation. The lower plastic rock guard is temporarily removed from the front

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INC. APPLICATION: 2006-2008 FORD F-150 PART NUMBER: 45-92010, 40-92015 WINCH MOUNTED SPORTSMAN GRILLE GUARD ITEM QUANTITY ITEM DESCRIPTION TOOLS NEEDED 1

More information

INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter

INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Fixed Bracket Bed Extender Titan (2016-) Bed Extender (999T7 W4100) Installation of this accessory requires installation of

More information

»Product» Safety Warning

»Product» Safety Warning #J9320, J9321 Installation Instructions 1986-1995 Jeep YJ 3" Body Lift Kit Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products

More information

Installation, Operating Instructions and Replacement Parts Installation video available at

Installation, Operating Instructions and Replacement Parts Installation video available at Installation, Operating Instructions and Replacement Parts Installation video available at www.kool-shield.com/support/ Made in the USA By Humboldt Specialty Manufacturing Co. www.kool-shield.com Revision

More information

RTX 2000 Thomas Compressor TG-550 Graco PN

RTX 2000 Thomas Compressor TG-550 Graco PN RTX 2000 Thomas Compressor TG-550 Graco PN 246888 Print of Complete Compressor--------------Page 2 Instruction for Kit 118628-------------------Page 3 Instruction for Kit 287845-------------------Page

More information

Please visit for the latest version of these installation instructions.

Please visit   for the latest version of these installation instructions. Please visit www.blueox.com for the latest version of these installation instructions. BX3620 Please read BOTH these and the General Information prior to installing or operating this equipment. Serial

More information

09-12 Dodge 4WD /4 Body Lift

09-12 Dodge 4WD /4 Body Lift 92RC80000 09-12 Dodge 4WD 1500 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publication No. MII 15249 WINCH MOUNT KIT P/N 08L70-HL3-A41 SXS700/M4/M2 Issue Date September 2015 PARTS LIST No. Description Qty (1) Winch bracket 1 (2)

More information

TECHNICAL DATA BROCHURE ZTR 308/3II

TECHNICAL DATA BROCHURE ZTR 308/3II Date 8/84 Page 1 of 6 TECHNICAL DATA BROCHURE ZTR 308/3II IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATION OR MAKING ADJUSTMENTS. ' Seat Adjustment Loosen bolts on sliding brackets under each side of

More information

INSTALLATION & OWNER S MANUAL

INSTALLATION & OWNER S MANUAL INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS FOR E-Z-GO MPT BALL CAGE (p/n 72685-G01) The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation

More information

Four Wheel Drive Kit Groundsmaster 580D

Four Wheel Drive Kit Groundsmaster 580D Four Wheel Drive Kit Groundsmaster 580D FORM NO. 957 Rev B Model No. 0599 00 thru 99999 INSTALLATION INSTRUCTIONS POTENTIAL HAZARD Traction Unit rolls over. WHAT CAN HAPPEN Bodily injury could occur. 4

More information

2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware

2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Owner s Manual Model: Polaris RZR * 2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions

More information

R8 Exhaust Installation Guidelines

R8 Exhaust Installation Guidelines STāSIS Engineering R8 Exhaust Installation Guidelines Exhaust Muffler support bracket bolt to muffler Muffler support bracket to chassis Muffler heat shield screws Heat shield bolt to chassis beneath anti

More information

BX Dodge Nitro Jeep Liberty Limited 4x4 Installation Instructions

BX Dodge Nitro Jeep Liberty Limited 4x4 Installation Instructions 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar with our products and have the equipment and knowledge to do fit work. When necessary Blue Ox

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS SPORTSMAN GRILLE GUARD / HDX GRILLE GUARD APPLICATION: 2016 Chevrolet Silverado 1500 PART NUMBER: 40-3875, 45-3870, 57-3870, 57-3875 ITEM QUANTITY DESCRIPTION

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SVA-110 2007 CIVIC 2-DOOR All33536-34848 Issue Date FEB 2007 PARTS LIST 11 Wire ties Right fog light Clip Left fog light 4 Stepped

More information

KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console)

KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console) KK-K9-F16-K INSTALLATION INSTRUCTIONS K9 Kit for 2011-2016 FORD EXPLORER (Retail Model Vehicle with OEM Center Shifter Console) TOOLS Needed: Phillips Screw Driver Power Drill with Drill Bits Trim panel

More information

ROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8

ROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8 Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory HITCH Application 2012 CROSSTOUR Publications No. AII 46198 Issue Date JULY 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-TP6-101 Upper spacer A (5 mm) (Some are not used.)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory S Application 2012 CIVIC 4-DOOR Publications No. AII 45623 Issue Date APR 2011 PARTS LIST Fog Light Kit P/N 08V31-TR0-100B (without automatic lights) P/N 08V31-TR0-100C

More information

LGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions

LGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative

More information

REF QTY PART DESCRIPTION PART NUMBER 1 1 Side Mirror, Driver (Not Shown) 1 Loctite - 263, 0.5 ml, Red Instructions

REF QTY PART DESCRIPTION PART NUMBER 1 1 Side Mirror, Driver (Not Shown) 1 Loctite - 263, 0.5 ml, Red Instructions MIRROR KIT P/N 2881001, 2881002, 2881011, 2881012 APPLICATION em1400, em1400 LSV or M1400 BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain

More information

Illustrated Parts List

Illustrated Parts List Illustrated Parts List Hydrostatic Lawn Tractor IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal combustion engine and

More information

HiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black

HiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your

More information

PARTS LIST WARHORSE 27 & 27 VAC-TRAC

PARTS LIST WARHORSE 27 & 27 VAC-TRAC PARTS LIST WARHORSE 27 & 27 VAC-TRAC PERFORMER WIRING DIAGRAM 248 PERFORMER SERVICE PARTS NSS NO. ONAN NO. DESCRIPTION 6590941 110-3709 GASKET - VALVE COVER 6590951 154-2495 GASKET - INTAKE MANIFOLD 6590961

More information

Safety First. Please remember to always use SAFE shop practices when performing all service procedures.

Safety First. Please remember to always use SAFE shop practices when performing all service procedures. Safety First Please remember to always use SAFE shop practices when performing all service procedures. 2006 Update Manual January 2006 Country Clipper 2006 Update Manual Index Joystick Kill Switch Oil

More information

PART NUMBER: MINI Cooper S L4-1.6L SEE * NOTE

PART NUMBER: MINI Cooper S L4-1.6L SEE * NOTE Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-699 2007-2010 MINI Cooper S L4-1.6L SEE * NOTE * NOTE: Legal in California only for racing vehicles which may

More information

FRONT STABILIZER BAR KIT

FRONT STABILIZER BAR KIT FRONT STABILIZER BAR KIT P/N 2881205 APPLICATION RZR XP 1000 MY16 and Newer, RZR XP 4 1000 MY16 and Newer BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted

More information

Installation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo

Installation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo Installation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. 1. 4. 5. At this type of installation

More information

SERVICE PROGRAM SP NOVEMBER 2007 SERVICE MANAGERS / PARTS MANAGERS NOTE:

SERVICE PROGRAM SP NOVEMBER 2007 SERVICE MANAGERS / PARTS MANAGERS NOTE: ATTENTION: SUBJECT: SERVICE MANAGERS / PARTS MANAGERS INCORRECT SPACING AND ALIGNMENT BETWEEN THE FAN, FAN RING, AND RADIATOR SHROUD; INCORRECT FAN RING SEAL INSTALLED To determine whether a particular

More information

Instruction Sheet Kit Number:

Instruction Sheet Kit Number: Instruction Sheet Kit Number: 72101800 TRACK CONVERSION KIT For All Wheel-Drive 921000 Models WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand,

More information

FOG LAMPS INSTALL KIT

FOG LAMPS INSTALL KIT FOG LAMPS INSTALL KIT PT CRUISER INSTALLATION INSTRUCTIONS Read entire instructions thoroughly before starting. For proper aiming of fog lamps, follow procedures in the service manual. NOTES: Left and

More information

»Product» Safety Warning

»Product» Safety Warning D2201 Installation Instructions 2012-2014 Dodge Ram 1500 4WD 2" Adventure Series Suspension System Read and understand all instructions and warnings prior to installation of product and operation of vehicle.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory TRAILER HITCH Application 2011 ODYSSEY Publications No. AII 43937 Issue Date SEP 2010 PARTS LIST Trailer Hitch Kit P/N 08L92-TK8-100 Trailer Hitch Harness Kit P/N 08L91-TK8-100

More information

2011-up Polaris RZR 800* Cab Enclosure Kit. Caution: Before using this product, read this manual and follow all safety instructions.

2011-up Polaris RZR 800* Cab Enclosure Kit. Caution: Before using this product, read this manual and follow all safety instructions. Owner s Manual Model: Polaris RZR * 2011-up Polaris RZR 800* Cab Enclosure Kit Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions Kit Contents

More information

Installing the PBX-PIT01 or PBX-PIT05 Pit Bar in the Ford Police Interceptor Utility

Installing the PBX-PIT01 or PBX-PIT05 Pit Bar in the Ford Police Interceptor Utility 25500242 Rev. B0 0216 Safety Message to Installers and Service Personnel of Emergency Vehicle Safety Equipment Installing the PBX-PIT01 or PBX-PIT05 Pit Bar in the 2011 2016 Ford Police Interceptor Utility

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDN-100 2004 ACCORD 2-DOOR AII 25735 Issue Date SEP 2003 NOTE: The outside temperature gauge can not be installed in a vehicle

More information

LANCER EVOLUTION (2008 ) MUD FLAP MZ531356EX (Black with aluminum plate) MZ531357EX (Black standard) INSTALLATION AND HANDLING INSTRUCTIONS

LANCER EVOLUTION (2008 ) MUD FLAP MZ531356EX (Black with aluminum plate) MZ531357EX (Black standard) INSTALLATION AND HANDLING INSTRUCTIONS LANCER EVOLUTION (2008 ) MUD FLAP MZ531356EX (Black with aluminum plate) MZ531357EX (Black standard) INSTALLATION AND HANDLING INSTRUCTIONS Black with aluminum plate -MZ531356EX Black standard -MZ531357EX

More information