New Life for an Old Model 500!
|
|
- Julian Potter
- 6 years ago
- Views:
Transcription
1 New Life for an Old Model 500! I had two Mossberg 500 barrels that I wasn t using on my main hunting shotgun, and that spelled PROJECT! One was an 18 inch cylinder bore riot barrel with no vent rib and a tritium front bead. The other was a parkerized 20 inch vent rib barrel threaded for choke tubes. At one time I had owned three Model 500 s, but was down to one. I looked in pawnshops for about six months until I found the gun in the topmost pix of this page. It was a neglected mutt, and used plus abused! It had started life as a black stocked, mil-spec M500 with 2 3/4 inch chamber and a riot barrel like the spare 18 inch one I had. The original barrel was MIA and the added barrel was 28 inches with a 3 inch chamber. It would fi re a 3 inch shell, but not eject the spent hull as the port was made for 2 3/4 inch shells only. Then there were several layers of spray paint camo applied over the matte black fi nish on the aluminum receiver and synthetic stock set... In this picture, look at all the rust and corrosion on the internal surfaces of the receiver and on the mag follower, but the price was right at $100. I knew from past work on these guns that if the follower was that bad, the spring would be worse. Adding to the diffi culty, MOST Model 500 mag tubes are red-loctited in place. You have to heat the steel mag tube up just enough to make the loctite begin to smoke, but in a careful, gradual manner that won t warp the aluminum receiver.
2 Since the barrel headspace is set at the factory by the distance of the muzzle end of the mag tube to the front face of the receiver, it s pretty important to get the mag tube BACK to that position at reassembly. So I counted (and made a note) of 2 exposed threads not set into the receiver, then used a small sharp chisel to leave a witness mark on both receiver and mag tube to assure proper indexing of the tube. For safety, I prepped my work area carefully before fi ring up the propane torch. A fi re extinguisher is right off camera, and note several layers of heavyduty foil protecting the table. Also notice that I have a fairly clean work area and no paper nearby. Gloves and a BBQ lighter fi nished the prep work. In the picture below, I have clamped the receiver as tightly as I felt I could without crushing it between the two wood blocks. That blue clamp is a BEAST that weighs about 12 pounds! This set-up would insure the best chance of breaking the tube free once the right amount of heat was applied.
3 Once I fi red up the torch, I never let the fl ame get any closer than 3/4 of an inch from the receiver or let it stop in one spot for more than 5 seconds at a time. I worked back and forth around the tube from about 3-4 inches from the receiver to back within that 3/4 inch. It took about 5 minutes of this for the fi rst smoke to rise from the Loctite. I shut down the torch, and grabbed my pre-positioned strap wrench. Note that I put the rubber strap no closer than shown to the heated area. I had done a dry-run of this part before I started with the torch so I knew that I would still have a ton of mechanical advantage from this position to bust that sucker loose. It came loose with only about two-thirds of my strength brought to bear, and I rotated it around two full turns before I took the wrench off to turn by hand.
4 Notice I still have heavy gloves on. That tube is hotter than it looks! Carefully fi nish turning the tube out. Be aware - there s a big captured spring in there! Keep control of the tube and ease the pressure off slowly as the tube comes off. Make a note of this, I would only apply blue, removable Loctite upon reassembly. Since the factory worries about improper headspace if you don t take caution, they use the permanent threadlocker to lessen the chance of liability if reassembly is done wrong. YUCK! In this case, I hate being right! Since the mag spring is not easily serviceable, most I have encountered have been pretty well abused. This one is as bad as they come though...
5 Note the kinks in the spring that are even more worrisome than the rusting. I might HUNT with that spring, but not bet my life on it! The new spring comes from Wolff Gunsprings ( and I also went with a high-visibility synthetic follower. This model from Choate ( estock.com) is as rugged as it is functional, and it will never rust like the factory one. I straightened the kinks as best I could, then counted coils instead of measuring length. That will always be more accurate after the factory spring has been under compression for several years. I also add at least 2-3 coils at fi rst and leave them if the weapon functions with a full load of shells. If it won t accept the specifi ed amount of shells, then I remove and clip back a couple until it will. Wolff replacement springs are made to trim to fi t. Clip the spring neatly with a quality wire cutter, then remove the burr at the cut end with some fi ne sandpaper.
6 I use a pair of non-marring (without grooves) pliers to bend the spring to have a fl at coil at each end. This will also help eliminate kinks. It is easy to see how the fl at end would produce a more even pressure on the follower. I chucked an old section of synthetic ramrod into a hand drill and put some 000 steel wool into a slotted shotgun rod tip. I plugged the muzzle end of the mag tube and squirted in a healthy dose of light oil. Then I put on goggles and a shop apron and went outside before polishing the heck out of the inside of the mag tube. Replace the wad of wool as needed. Keep this up until a patch comes out clean. That will be a while!
7 There are a world of gun assembly books with info on the disassembly/reassembly of this fi rearm. But DO use one, as there are a few tricks that will save a lot of frustration. After I fi nished polishing the mag tube, I stripped off the layers of spray paint from the tube and receiver. The original matte black fi nish on the receiver was still under the paint. I used a matching bake-on fi nish on the magtube exterior. Quite a difference from the gun I brought home from the pawnshop! I used it two months later to harvest this Tennessee Tom during spring turkey season. Satisfying on many levels, I assure you... When I change to the riot barrel, it makes a dandy home defense weapon as well! - perklo Notes on the Model 500 mag tube and model variants: 1) Because of the design, there aren t aftermarket mag tube extensions for the Model 500. The military Combat version, the Model 590, has a longer mag tube and thereby a different location for the barrel lug that screws into the mag tube. It also has a bayonet lug and heat shield. 2) A sub-model (Model 500A) was produced for a few years with a few mechanical differences. Most notable was a safety on the triggerguard instead of under the thumb on top of the receiver.
BBK Ceramic Long Tube Headers (99-04 Cobra and Mach 1) - Installation Instructions
BBK Ceramic Long Tube Headers (99-04 Cobra and 03-04 Mach 1) - Installation Instructions The below installation instructions work for the following products: BBK Ceramic Long Tube Headers (99-04 Cobra
More informationLakela nd H2 Low Speed Stator Coil Installation
Lakela nd H2 Low Speed Stator Coil Installation Step 1: Place the stator assembly on a padded surface to protect the plastic signal generators, and orient it as shown in figure 1. The low speed coil is
More informationINSTALLATION INSTRUCTIONS
2705 INSTALLATION INSTRUCTIONS 5-6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This kit is to be used on a pickup truck only, and
More informationBLASTING SYSTEMS INSTRUCTIONS FOR & Part #13667
BLASTING SYSTEMS INSTRUCTIONS FOR 13943 & 13944 Part #13667 EASTWOOD BLASTING SYSTEMS Abrasive blasting has always been an alternative to chemical stripping on most parts of an antique or specialty car.
More informationINSTALLATION INSTRUCTIONS
270 INSTALLATION INSTRUCTIONS 5-6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This kit is to be used on a pickup truck only, and
More informationInstructions for repairing the F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs)
Instructions for repairing the 1986-87 F-Body Hatch Pull-Down Unit By Lon Salgren (ls90rs) Lonsal@adelphia.net CAUTION: Completely read and understand the instructions before proceeding. There are some
More informationHow to Change Front Brake Pads on a Toyota Corolla
How to Change Front Brake Pads on a Toyota Corolla Link to this article on (All other links in this document are disabled) Follow this picture guide to change the front brake pads on a 2003-2008 Toyota
More informationINSTALLATION INSTRUCTIONS
2583 INSTALLATION INSTRUCTIONS 7-16 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. DO NOT INSTALL IF THE TRUCK HAS BEEN LIFTED AND THE
More informationriderite.com INSTALLATION INSTRUCTIONS
2528 INSTALLATION INSTRUCTIONS 4-16 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This kit is to be used on a pickup truck only, and
More informationInstallation Instructions Console Megashifter
Installation Instructions Console Megashifter 1968-1969 Camaro Part Number 81035 This B&M Megashifter is designed to fit in the console of a 1968-1969 Chevrolet Camaro. In 1968, these vehicles were equipped
More informationINSTALLATION INSTRUCTIONS
2706 INSTALLATION INSTRUCTIONS -6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This kit is to be used on a pickup truck only, and
More informationELECTRIC BENDING IRON
ELECTRIC BENDING IRON This is intended as a short pictorial essay on the construction of an electrical side bending iron. As the items used may vary from the ones shown here, only limited dimensions are
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationShotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationInstallation Instructions
Instructions Created by an: Samurai Rear Diamond Plate Corners (Pre-bent) (SKU# SEB-RDP) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationRebuilding of the Dana 25 (front axle) Chris Stout
The inside gears and bearings were all in excellent condition. A fluid change and some good cleaning was all the was necessary. However, the pinion shaft seal was shot as were the front wheel bearings
More informationPart# JL AIR IT UP 4 Tire On Board Air Delivery System. (Requires External Air Source)
Part# 18-1819 JL AIR IT UP 4 Tire On Board Air Delivery System (Requires External Air Source) The most up-to-date instructions always visit www.updownair.com www.updownair.com 833-226-4863 I M P O R T
More informationThis LED flashtube kit covers models 400, 404, 500, 504, 600, 680 & 506.
L.E.D. INSTRUCTIONS I D T S O T U B I R M O C R Y N A P Kit contains: This LED flashtube kit covers models 400, 404, 500, 504, 600, 680 & 506. For the power supply: 1-LED power supply circuit board, 2
More informationINSTALLATION INSTRUCTIONS
28 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY 2-5 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This
More informationEurocompulsion Camshaft Installation
Eurocompulsion Camshaft Installation Introduction, please read. The purpose of this article is too assist our customers with installation of a performance camshaft in the Fiat Multiair 1.4 Turbo. The operation
More informationVehicle Specific Instruction Notes
Vehicle Specific Instruction Notes Most later model vehicles use a plastic and felt anchoring strip in place of the older metal rods. We have provided rod pouches on all of our new seat skins that will
More informationPeg-Harness installation instructions
Peg-Harness installation instructions I know it s not the easiest thing to do, but PLEASE READ THESE INSTRUCTIONS COMPLETELY so you will understand what you are trying to accomplish before you start drilling
More informationPower Seat Side Mount Installation & Wiring Instructions
F22/F30/F31/F32/F80/F82/F87 (and other cars with the same sliders) Power Seat Side Mount Installation & Wiring Instructions These instructions assume a basic comfort with crimping and/or soldering. That
More informationCHANGING REAR SHOCKS/REAR SHOCK MOUNTS on an E36/8 Z3 M Coupe
CHANGING REAR SHOCKS/REAR SHOCK MOUNTS on an E36/8 Z3 M Coupe Remove the rear luggage compartment floor trim. Remove the right (passenger side) rear compartment cover, and the M Mobility System. Remove
More informationInstallation Instructions:
Installation Instructions: Type of Operation: Motor Type of Mount: Outside All directions are provided assuming the installer is looking at the door from the coil side of the opening. (see drawing below)
More informationSoft Top Rear Locking Cylinders
Soft Top Rear Locking Cylinders Level of difficulty: Fairly easy very rewarding! Tools needed: - M10 socket and ratchet - Flat screwdriver or needle nose pliers or small hooked tool for removal of hydraulic
More informationINSTALLATION INSTRUCTIONS
2595 INSTALLATION INSTRUCTIONS 2-6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. DO NOT INSTALL IF THE TRUCK HAS BEEN LIFTED AND THE
More informationINSTALLATION INSTRUCTIONS
2807 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY -6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This
More informationInstallation Instructions
Instructions Created by an: 86-95 Suzuki Samurai Samurai Front Axle Knuckle Rebuild Kits (SKU# SAX-KRK) Installation Instructions Revised 6-6-14 Suggested Tools: CAUTION: Safety glasses should be worn
More informationDoor Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More informationFree Flow Exhaust Installation Instructions
Free Flow Exhaust Installation Instructions PART NUMBER: APPLICATION: D660-0035 (polished tips) or D660-0035-BLK (black ceramic tips) 2010-11 X5-M & X6-M Parts List 1 D663-0159 (-BLK, for black tips) X5
More informationINSTALLATION INSTRUCTIONS
2806 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY -6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This
More informationLowering Spring Installation on a Mustang GT
Lowering Spring Installation on a 99-04 Mustang GT This installation is very the same installation that many of the 79-04 Mustangs excluding Cobra require. Time to install: 2-3 hours to do alone with a
More informationДнепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling
Ural (Урал( Урал) - Dnepr (Днепр( Днепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling (applies also to K-37 K and K-38 K carbs) Ernie Franke eafranke@tampabay.rr.com
More informationRemoving your Two-blade Hartzell HC-12 (?) 20 prop off a Franklin Engine (Or How do I change the prop cylinder O-rings! )
Removing your Two-blade Hartzell HC-12 (?) 20 prop off a Franklin Engine (Or How do I change the prop cylinder O-rings! ) If you are having oil leaking around the propeller piston/cylinder assembly and
More informationDoor panel removal F07 5 GT
Things needed Decent plastic trim removal tools Torx 30 Spare door clips 07147145753 I got away with a set of 5 but if I did it again I d be cautious and get 10. From prior experience if they are damaged
More informationInstallation Instructions:
Installation Instructions: Type of Operation: Motor Type of Mount: Outside All directions are provided assuming the installer is looking at the door from the coil side of the opening. (see drawing below)
More informationCommander SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 - FRONT UPPER A-ARMS 2 - FRONT LOWER A-ARMS 4 - COTTER PINS 2-12MM JAM NUTS 2 - TIE ROD EXTENDERS 8- FLANGED DELRON BUSHINGS 4- DELRON CASTER SPACERS 6 - GREASE FITTINGS 3 - BEARING REMOVAL
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationBottom Mount Seat Mount Installation & Wiring Instructions
E81/E87/E90/E91/E92/F22/F30/F31/F32/F80/F82/F87 (and other cars with the same sliders) Bottom Mount Seat Mount Installation & Wiring Instructions These instructions assume a basic comfort with crimping
More information2000 Mr2 Spyder Seat Cover Replacement Project
2000 Mr2 Spyder Seat Cover Replacement Project Tool List: Plastic Trim Tool, Hog Ring Pliers, Medium or Heavy Duty Wire Cutters, 12mm socket, 14mm Socket, Ratchet, Extension, Flat Head Screwdriver & Gloves
More informationInstallation Instructions:
Installation Instructions: Type of Operation: Motor Type of Mount: Inside All directions are provided assuming the installer is looking at the door from the coil side of the opening. (see drawing below)
More informationAssembling an AR-15 Parts CheckList:
Assembling an AR-5 Parts CheckList: Table of Contents Upper Receiver Common Parts.............................. A, A2 & A3 sights............................................. 2-3 BARREL COMPONENTS.........................................
More informationThe H-MAC Heavy Metal Articulating Chassis Construction Guide
The H-MAC Heavy Metal Articulating Chassis Construction Guide The Heavy Metal Chassis is constructed with two identical drive modules built using 10 mechanical sub-assemblies. The drive modules are integrated
More informationThrottling Pendulum Gate O-ring Replacement Procedure Rev. A, May 2012
Throttling Pendulum Gate O-ring Replacement Procedure Rev. A, May 2012 This procedure covers the replacement of the gate O-ring of the Nor-Cal Pendulum Gate Valve, with the gate valve housing installed
More informationINSTALLATION INSTRUCTIONS
280 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY 2-5 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This
More informationDexter Never-Adjust Brake Install
Dexter Never-Adjust Brake Install Arctic Fox 2007 29-5T Warning: This involves lifting your trailer, working under and around it. If you do not have the correct equipment and knowledge for this, please
More informationThank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc.
Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc. We took much pride in putting together a fuel system that would deliver a maximum amount of fuel as simply as possible
More information$1.00 FOR THE TQIO/RCIO
$1.00 FOR THE TQIO/RCIO m mm HDBBYSHOP Champion Jay Halsey has an impressive track record. One of Jay's advantages is a whisper smooth tranny thanks to his dad, Jim. Now you can build a Halsey transmission!
More informationSide Mount Installation & Wiring Instructions
E81/E87/E90/E91/E92/F22/F30/F31/F32/F80/F82/F87 (and other cars with the same sliders) Side Mount Installation & Wiring Instructions These instructions assume a basic comfort with crimping and/or soldering.
More informationPLP Compression Dead-end & Jumper Terminal for ACSR & ACSS Conductors
MARCH 2017 PLP Compression Dead-end & Jumper Terminal for ACSR & ACSS Conductors Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED
More informationCALDERA 10E Spur Gear Change
CALDERA 10E Spur Gear Change www.thirdcoastrc.com ebay handle - little*oak Click Below to Visit our Ebay Store EBAY STORE (Please take a moment and bookmark my website, ebay store, and save me as an ebay
More informationRostra Electronic Cruise Control Install On a Stratoliner or Roadliner
Rostra Electronic Cruise Control Install On a Stratoliner or Roadliner MATERIALS LIST: 1 - Rostra Part # 250-1223 (www.brandondist.com/products/cruise1223.htm) 1 - Signal Splitter part # 250-4369 1 - Engagement
More informationFORK FREE PISTON MODIFICATION 2011 HONDA CRF250R
217 Lorain Place Los Gatos, California 95032 408.406.2089 www.smartperformanceinc.com www.spi-racing.com FORK FREE PISTON MODIFICATION 2011 HONDA CRF250R WHAT? All production versions of the 2011 HONDA
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationAEROMOTIVE Part # & Stealth Fuel Tank Sump INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 18651 & 18652 Stealth Fuel Tank Sump INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend
More informationHFB Steering Gear Service Manual
TRW Automotive Commercial Steering Systems HFB Steering Gear Service Manual HFB64 SERIES Die Cut HFB64 Integral Hydraulic Power Steering Gear This steering gear was specifically designed for motor trucks;
More informationFitting a.45 ACP Conversion Cylinder Copyright 2014 Roy Seifert
Copyright 2014 Roy Seifert Disclaimer: This article is for entertainment only and is not to be used in lieu of a qualified gunsmith. Please defer all firearms work to a qualified gunsmith. The author assumes
More informationH31 BOOSTER REBUILD & MASTER CYLINDER
2010 1991 BMW 750iL George Fontes gajfontes@yahoo.com H31 BOOSTER REBUILD & MASTER CYLINDER Rebuild hydraulic booster and replace Master Cylinder. Page 1 of 16 Master Cylinder Removal & Brake Booster Rebuild
More informationAdjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003
SECTION ONE: Get Prepared - Tools Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 Courtesy of: Half-Crazy Get a manual impact driver (the kind you hit
More informationRichmond County Gunsmithing - Services List and Pricing
Richmond County Gunsmithing - Services List and Pricing This is not a complete set of services provided. Please call for more info. All services require presentation of a valid and current government issued
More informationINSTALL INSTRUCTIONS
INSTALL INSTRUCTIONS Models: 6005 & 6005TK (For Non Electric Mirrors) GM CK Body Style If your stock mirrors are stock electric the wrong set has been ordered. Do not attempt to manually extend or retract
More informationDoor panel insert trim replacement Volvo V70
Door panel insert trim replacement 1998-2000 Volvo V70 Tools needed: Torx Driver T25, Putty Knife, Bone Tool (optional), Heat gun or Dremel cutting tool, wire brush (or use a plastic tile and grout brush),
More informationStirling Engine. What to Learn: A Stirling engine shows us how energy is converted and used to do work for us. Materials
Stirling Engine Overview: The Stirling heat engine is very different from the engine in your car. When Robert Stirling invented the first Stirling engine in 1816, he thought it would be much more efficient
More informationPLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!!
JDM power folding mirror switch install into stock USDM harness. By: Greg L., Zeke21 on twinturbo.net PLEASE READ THROUGH THE WHOLE WRITE UP BEFORE ACTUALLY USING IT!!!! This is how I was able to get the
More informationSHARK UPPER WINDSHIELD FRAME & WINDSHIELD REPLACEMENT. Text and Photos by TOM BENFORD
Text and Photos by TOM BENFORD I purchased a fathom green 69 big-block tri-power T-top coupe with only 42,000 original miles on it recently. I'm the third owner of the car, and I got it for a very good
More informationThough Indian s 111-cubic-inch engine delivers a
TECH by Chris Maida Andrews Indian 111 Camshafts Part I: Removing the cams from the camshaft compartment Tools Needed Red Loctite Clean rags 6mm Allen 5/64" Allen 3/32" punch External circlip pliers Needlenose
More informationupper and lower ball joints ( I went with Moog from rockauto.com): two K80026 and two K8607T
Parts required: two 5C3Z*4A322*AA = hub / steering knuckle o-ring two AC3Z*1S175*A = updated axle shaft "dust seal" two 5C3Z*3254*A = steering knuckle / axle shaft seal upper and lower ball joints ( I
More informationInstalling AMP-wiring in a New Beetle
Installing AMP-wiring in a New Beetle Vehicle used: New Beetle 2.0i Type 9C (1999) Used set of cables: Dietz 35mm² power cable, double shielded Dietz chinch cable ( 35mm² Professional Line ) First of all:
More informationBBK Caster/Camber Kit (87-93)
BBK Caster/Camber Kit (87-93) Materials in the box 2 Polished Aluminum Plates 2 Steel Strut Mounts 4 Polyurethane Bushings 2 Stud Plates 2 Bushing Sleeves 2 5/8 Flat Washers 2 5/16 Allen Head Bolts 4 5/16
More informationINSTALLATION GUIDE Bolt-On Drag-Race Strut Clip Chevy II
INSTALLATION GUIDE 7702 Bolt-On Drag-Race Strut Clip 1962-67 Chevy II Description: STRUT CLIP 4130 BOLT ON 62-67 CHEVY II, INCLUDES 4130 ROUND TUBE FRAME CLIP, DOUBLE-ADJUSTABLE STRUTS, ADJUSTABLE-HEIGHT
More informationRevision Date: Building a dual pump system for an open boat. Description:
Disclaimer: The information is provided as-is. The author(s) accepts no liability for the accuracy, availability, suitability, reliability and usability. The following information is in the public domain
More informationInstallation Guide for Rough Country 2.5 inch Lift Kit w/o Shocks (07-15 Wrangler JK) Item # J10212
Installation Guide for Rough Country 2.5 inch Lift Kit w/o Shocks (07-15 Wrangler JK) Item # J10212 Installation Time: 3 Hours Tools Required: Jack (2 helps, but not needed) Jack stands(2 3-ton, 2 2-ton)
More information2012 Pro Stock Rules
2012 Pro Stock Rules Areas highlighted in red are changes for 2012 Revised 5-5-2012 PRO STOCK: Any North American made car 1968 to present. This division was created as a controlled, economical and competitive
More informationKodak 750H Carousel Projector Repair
Kodak 750H Carousel Projector Repair An AT YOUR OWN RISK PROJECT by Klaus Wolter, Rev B, 3-26-2016 Here I documen the repair of my 750H carousel. A common problem with this projector, and all of the projectors
More information1967 (Late) and 1968 CORVETTE TELESCOPING STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS - PAPER #1
Last Revision: 03SE2012 1967 (Late) and 1968 CORVETTE TELESCOPING STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS - PAPER #1 Disassembly and Repair Instructions Addressed in this Paper Difficulty Page
More informationTire Patch Kit Showdown!
Tire Patch Kit Showdown! We ve traveled about 25,000 flatless miles this season. Normally this would be a really good thing but the lack of holes in our tires made it pretty hard for us to put two very
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationMAIN ROTOR TRANSMISSION CHIP DETECTOR
MAIN ROTOR TRANSMISSION CHIP DETECTOR 13 October, 2014 In my second and last Helicycle I want to make everything better than the first one. That includes not only a transmission chip detector, but one
More informationREAR INTERIOR AMBIENT LED FITTING INSTRUCTIONS AUDI A4(B6) 2001 onwards
GLUE is required to secure the supplied lighting module into place, and is not included as part of this modification kit. Please read the instructions fully before commencing this modification. NOTE: Ensure
More information2019 Full Size Derby Rules. Only 50% of your car can be painted black! NO All Black Cars!!!!
1 2019 Full Size Derby Rules Only 50% of your car can be painted black! NO All Black Cars!!!! Every car must have a roof sign with a visible car number and the driver s door must be painted white!!! WE
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-783C (Gun Metal Gray Finish) 2016 HYUNDAI TUCSON 1.6L TURBO C.A.R.B. E.O# D-670-24 2017 HYUNDAI TUCSON 1.6L TURBO
More informationPontoon Assembly Instructions and manual. Read before using hoist.
Page 1 Pontoon Assembly Instructions and manual. Read before using hoist. For Models 32BL18, 32BL22, 32BL25 and 42BL28 R Model 32BL22 Shown Proudly Made in Michigan By NuCraft Metal Products 402 Southline
More informationOptima K Badge Removal & Installation Tutorial
P.1 2014-2015 BADGE INSTALLATION & REMOVAL HOOD, TRUNK, AND STEERING WHEEL ***Modification to the rear K Badge emblem of 2011-2013 Optima models as directed in this tutorial is not necessary*** Tools and
More informationSpikes-Spider Hub Installation
Spikes-Spider Hub Installation The instructions that are provided with the Spikes Spiders are pretty good. I've created this page for two reasons: to show those that are thinking of buying a set exactly
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationDUAL REMOTE OIL FILTER MODIFICATION 4 TH GENERATION FIREBIRDS
Written by Dave Dorey (lonetechie) Copyright FirebirdNation.com The following article details how I installed a dual remote oil filter system on my 2001 Formula Firebird. If you decide to tackle this project,
More informationPage 1. File: Motolight caliper one-piece Date: 8/14/2006
Page 1 Caliper Mount Installation One-piece mounting brackets You should allow about two to three hours for installation. We suggest you use a well-lighted space for installation. PLEASE READ ALL THE INSTRUCTIONS.
More information4 th Gen 4 Runner Front Bumper - Installation Instructions:
www.shrockworks.com info@shrockworks.com 877-474-7625 4 th Gen 4 Runner Front Bumper - Installation Instructions: Thank you for purchasing a ShrockWorks product. We are confident you will enjoy it for
More informationInstallation Instructions QUICKSILVER CONSOLE SHIFTER Fits: Chevelle / El Camino
WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent movement in
More informationRear drum to disk conversion for a 00 Toyota Camry LE 4 cylinder
Rear drum to disk conversion for a 00 Toyota Camry LE 4 cylinder *** Read and use at your own discretion I assume no liability for what you or anyone else does with this information. By reading this, you
More informationINSTALLATION INSTRUCTIONS South Highway 11 Westminster, SC Toll Free (888) (864) FAX (864)
These instructions apply to the servicing of the Lift Technologies MaxiMizer Integral Sideshifters Cylinder Head. WARNING! Unless the steps in the following Installation Instructions are properly followed
More informationDUAL MAGNET DRILL. Mactech Dual Magnet Drill OPERATING MANUAL SERIAL NO. SUBSEA MACHINING SOLUTIONS
DUAL MAGNET DRILL MACTECH PORTABLE MACHINING SOLUTIONS MACTECH PORTABLE MACHINING SOLUTIONS Mactech Dual Magnet Drill OPERATING MANUAL SERIAL NO. Mactech Offshore 3129 Highway 90 East Broussard, LA 70518
More informationModular Engine 1, 2008 revision August 3, 2008
Modular Engine 1, 2008 revision August 3, 2008 David Kerzel 2008 Back in 2002 I wanted to build a bunch of different engines without a lot of detail to learn how to build an engine, what works and what
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-796C (GUN METAL GRAY FINISH) 2015-2016 HYUNDAI GENESIS SEDAN 3.8L V6 C.A.R.B. E.O # D-670-24 1 ITEM NO. PART
More informationThe HMC-Lite Construction Guide
The HMC-Lite Construction Guide The Heavy Metal-Lite Chassis is constructed using two identical drive modules. The drive modules are constructed using 3 mechanical sub-assemblies. The drive modules are
More informationLED NEON FLEX INSTALLATI ON GUI DE
LED NEON FLEX INSTALLATI ON GUI DE F I R E F L Y L I G H T I N G. C O M. A U WHAT IS LED NEON FLEX? THE MOST VERSATILE AND SIMPLE LIGHTING SYSTEM YOU WILL EVER USE LED Neon Flex is a green friendly, safe,
More informationWhat s in your new header system kit?
!"#$% "#$%& ' "())' **+ Congratulations on your purchase of the Dynatech / SuperMaXX system for the Dodge Magnum / Chrysler 300C. We believe, and think you will agree that this system is second to none
More informationVRSC-DX Truck-Lite LED Headlight Installation Instructions
VRSC-DX Truck-Lite LED Headlight Installation Instructions The following Instructions are for installing a 7 Truck-Lite LED headlight into a Harley Davidson VRSC-DX Night Rod Special fairing. Other 7 headlights
More information