Owners Manual: Flow Through Filter (FTF) System

Size: px
Start display at page:

Download "Owners Manual: Flow Through Filter (FTF) System"

Transcription

1 PROVENTIA EMISSION CONTROL carb-verified, level 2+ tru Filter RETROFIT Owners Manual: Flow Through Filter (FTF) System Including Installation Guide for Sentry Model TRUs Proventia Americas, LLC c/o Proventia Group, Tietotie 1, FI Oulunsalo, Finland Tel

2 2 contents CONTENTS Operators Information Operation and Maintenance Requirements... 3 Operators Pretrip Check... 4 Periodic Maintenance... 4 CARB Compliance Schedule for the Proventia FTF... 5 Installer and Service Technician information Preinstallation Checks... 5 Injector installation... 6 Installation... 9 Warranty Registration and Installer's Checklist...27 CARB Identification Number (IDN) Registration...27 Cleaning the FTF and Safe Ash-Handling Guidelines...27 Wiring Diagram for Backpressure Controller...28 Troubleshooting...29 Parts List...32 Warranty statements Warranty Statements...33

3 OPERATION AND MAINTENANCE REQUIREMENTS 3 OPERATION AND MAINTENANCE REQUIREMENTS In order for the Proventia FTF system to meet the CARB Verification requirements, the Transport Refrigeration Unit (TRU) owner must meet these operation and maintenance requirements before installation: 1) TRU owner is responsible for checking engine backpressure level at every Preventive Maintenance Interval (PMI) to determine whether accumulated ash within the FTF needs to be cleaned out. With the TRU running at high speed, check the backpressure on the backpressure indicator gauge. 2) TRU owner is responsible for confirming normal oil consumption rate greater than 50 hours/quart of oil before installation of the Proventia FTF to ensure proper filter operation (a new engine gets about 120 hours/quart of oil). 3) Fuel requirement: Use only Ultra Low Sulfur Diesel (ULSD). In California, both On-road and Off-road diesel is ULSD. In the other 49 states, only On-road diesel is ULSD (In June 2010, Off-road diesel in the other 49 states will become ULSD). Use of higher sulfur diesel will clog FTF. 4) Mixing lube oil with fuel is not allowed because it will cause excessive ash accumulation in the filter. 5) Engine: This Proventia FTF kit is verified for use on Sentry model years ) Follow TRU engine maintenance schedule. 7) Recommended for maximum filter life, but not required, is to use TRU engine oil compatible with ULSD applications, such as PC-10 low sulfate ash oil. 8) TRU engine injectors must be replaced with new or remanufactured injectors at the time of FTF installation. 9) This Proventia FTF system can impose a backpressure of up to 2.5 psi on the TRU engine at low-speed operation. There is a possible fuel consumption penalty of less than 1% when running with the Proventia FTF.

4 4 OPERATORS PRETRIP CHECK and PERIODIC MAINTENANCE OPERATORS PRETRIP CHECK Inspect backpressure indicator gauge with the TRU operating at high speed. If yellow gauge line is within the red service range of the gauge (see photo at left), the FTF filter should be serviced (see page 30). Photo at right shows the yellow indicator in the green normal range. PERIODIC MAINTENANCE At the regular TRU Preventive Maintenance Interval, check the Proventia FTF system: 1) Check to see if TRU is being forced to high-speed operation frequently by the FTF backpressure controller (cycle would be repeating 10 minutes high speed and 5 minutes low speed). If so, this indicates that the filter may have an excessive accumulation of soot or ash. See troubleshooting on page 30. 2) Check to see if the yellow gauge line in the backpressure indicator gauge is within the red service range (shown in picture at left) while the TRU is running in highspeed mode. If so, this indicates that the filter may have an excessive accumulation of soot or ash. See troubleshooting on page 30. 3) If black smoke is visible during steady speed operation, see troubleshooting on page 31.

5 COMPLIANCE SCHEDULE PREINSTALLATION CHECKS 5 CARB COMPLIANCE SCHEDULE Table shows compliance dates if Proventia FTF is installed. TRU Model Year TRU will be LETRU compliant until Total useful life of TRU 1985 December 31, years 1986 December 31, years 1987 December 31, years 1988 December 31, years 1989 December 31, years 1990 December 31, years 1991 December 31, years 1992 December 31, years 1993 December 31, years 1994 December 31, years 1995 December 31, years 1996 December 31, years 1997 December 31, years 1998 December 31, years 1999 December 31, years 2000 December 31, years 2001 December 31, years 2002 December 31, years PREINSTALLATION CHECKS Before installing the Proventia FTF system, the installer must confirm the oil consumption rate of the TRU engine and also replace the injectors. 1) Check the oil consumption rate using the following procedure (or confirm from recent TRU service records that oil consumption rate was at least 50 hours/qt): a. Add oil to the engine to the full mark on the dipstick. b. Record the engine hourmeter reading with engine oil at full: hours c. Run TRU for about 50 hours under normal operation. The TRU can be used on normal routes and deliveries. It is not necessary to remove the TRU from service during this oil consumption rate check. d. Again add oil to the engine to the full mark on the dipstick. e. If the engine used less than a quart (32 ounces) of oil in 50 hours, the oil consumption is okay. Proceed to number 2 on next page (Replace injector assemblies).

6 6 injector installation f. If the engine used more than a quart of oil in 50 hours, service the TRU engine per TRU manufacturer s guidelines to reduce the amount of oil the engine is burning before installing the Proventia FTF system. 2) Replace injector assemblies with new or remanufactured injectors available from Remanufactured injectors should be set at 2,800 to 3,000 psi for Yanmar injectors and 2,633 to 2,704 psi for Isuzu injectors. injector installation TOOLS: 17mm open-end wrench, 14 or 10mm socket wrench, injector removal tool PARTS: Isuzu or Yanmar injectors and gaskets 1) Remove injector line from top of injector. Remove injector hold-down collar. (Isuzu, 14mm socket)

7 injector installation 7 2) Remove injector line from top of injector. Remove injector hold-down collar. (Yanmar, 10mm socket) Yanmar injectors can be difficult to remove, due to corrosion. Running the Yanmar engine for 10 minutes to warm it up will make injector removal much easier. Isuzu injectors should be removed when the engine is cold. 3) Loosely thread injector removal tool on top of injector.

8 8 injector installation 4) Install injector removal tool tube, positioning the cutouts in the tube for the injector bleed line. Thread 1/2" nut onto injector removal tool until injector is lifted out of injector socket. If injector is difficult to remove due to rust, add liquid penetrant to loosen. Be careful not to damage metal injector bleed tubes, so that injector cores can be reused and remanufactured. 5) Install new o-ring and copper gasket with Isuzu injector. Put a spot of grease on the copper gasket to hold it in place during installation. Injector pressure spec is 2,633 to 2,704 psi. Torque injector stud nut to 27.5 ft-lb. 6) Install new nozzle protector and gasket with Yanmar injector. Injector pressure spec is 2,800 to 3,000 psi. Torque injector stud nuts to 12 ft-lb.

9 INSTALLATION 9 INSTALLATION 2 hours installation time SAFETY PRECAUTIONS 1) Disconnect positive battery cable from battery to prevent TRU from starting during installation. 2) Do not touch hot exhaust components; make sure TRU exhaust system is at room temperature before installing Proventia FTF system. 3) Use safety glasses and make sure to have a safe work platform when installing the Proventia FTF system. REMOVE MUFFLER TOOLS: 7/16, 1/2, and 9/16 socket wrenches PARTS: None 1) Remove the two bolts that hold the right muffler support onto the Sentry frame.

10 10 INSTALLATION 2) Remove and discard exhaust U-clamp. 3) Remove four bolts that clamp muffler onto both support brackets.

11 Installation 11 4) Remove muffler and two muffler clamps and discard. INSTALL manifold INSULATION TOOLS: 13mm socket or box-end wrench PARTS: insulation blanket with grommets, stainless steel tie bands (3), 2" fender washers (3), 8mm bolts (3) 1) On Isuzu se2.2 and Yanmar engines, remove three bolts holding engine exhaust manifold heat shield onto back of engine. Discard metal heat shield and old bolts.

12 12 Installation 2) Insert exhaust manifold insulation blanket through the side access door. 3) Install exhaust manifold insulation blanket using three new M8 x 1.25 x 20 metric bolts and 2 fender washers. There are five grommet holes in the blanket. These three holes are used on Isuzu engines:

13 INSTALLATION 13 4) These three holes are used on Yanmar engines: 5) Steel tie bands can be used as an alternative on Isuzu se2.2 engines.

14 14 INSTALLATION 6) Steel tie bands can be used as an alternative on Isuzu se2.2 engines. 7) Steel tie bands are used on Isuzu di2.2 engines. Bolts are not used.

15 Installation 15 INSTALL THE FTF TOOLS: 13mm socket wrench, 7/16" box-end wrench, 7/16" and 1/2" socket wrenches PARTS: FTF, backpressure fitting, FTF clamps (2), 8mm bolts (4) 1) Install backpressure fitting onto FTF inlet of FTF with 7/16" wrench. 2) Loosely install two FTF clamps using four 8mm bolts.

16 16 INSTALLATION R45 3) Position FTF with 1/2" clearance between FTF outlet and muffler support. 4) Loosely install R45 exhaust clamp onto FTF inlet. Insert flexible exhaust tube into FTF inlet.

17 Installation 17 For installation on Isuzu di2.2 engines with spiral wound exhaust tubing: 6) Relace the existing spiral wound tube with this assembly. 5) Relace the existing spiral wound tube with this assembly. Use Permatex Muffler & Tailpipe Sealer at joints.

18 18 INSTALLATION 7) Reinstall two bolts that hold right muffler support onto Sentry frame. Tighten four 8mm FTF clamp bolts. Tighten R45 exhaust clamp. 8) Install exhaust outlet elbow with an R48 clamp.

19 Installation 19 INSTALL BACKPRESSURE CONTROLLER TOOLS: 3/8 nut driver, pliers, 1/2 box-end wrench PARTS: Backpressure tube, controller assembly, P-clamp, self-tapping screws (5) 1) Install backpressure tube into backpressure fitting and tighten compression nut with 1/2" wrench. Bend tube for clearance with fan shroud. 2) Install backpressure controller using 3/8" nut driver and four self-tapping screws onto top of Sentry frame.

20 20 INSTALLATION 2) Install backpressure controller using nut driver and four self-tapping screws onto top of Sentry frame. 3) Connect silicone hose from controller to backpressure tube. Install hose clamp on end of hose.

21 INSTALLATION 21 5) Wrap insulation blanket around exhaust tube, between engine and FTF. Snap insulation blanket shut. 4) Install P-clamp with self-tapping screw to hold silicone hose onto shroud.

22 22 Installation WIRING THE BACKPRESSURE CONTROLLER TOOLS: 3/8 nut driver, 12mm open-end wrench PARTS: Tie wraps WARNING: Disconnect positive battery cable from battery to prevent TRU from starting during installation. 1) Connect backpressure controller wire #2 to the battery cable stud on starter solenoid. 2) Connect #7D controller wire to the 7D terminal on speed solenoid. 3) Connect CH controller wire to CH terminal on speed solenoid.

23 INSTALLATION 23 4) Install diode assembly on 7D terminal of speed solenoid. 5) Remove Thermo King 7D wire from speed solenoid and cut off ring terminal. 6) Remove 1/4" of insulation from end of Thermo King 7D wire, insert wire into connector on diode assembly, and crimp connector onto Thermo King 7D wire. 7) Apply heat to heat shrink tubing to seal onto 7D wire. 8) Use tie wraps to gather and route the backpressure controller wire harness. 9) WARNING: When routing the controller wire harness, make sure it does not touch any fuel lines. Diode assembly Proventia controller wires Thermo King harness wires CH and 7D

24 24 Installation INSTALL LABELS TOOLS: Rag and degreaser PARTS: CARB VDECS label, ULSD fuel label 1) Remove CARB VDECS label, which is tie-wrapped in a plastic bag to the FTF. 2) Clean and degrease the engine surface before installing the label. Install label so it is visible to a CARB inspector when opening the TRU service doors.

25 INSTALLATION 25 3) Install the ULSD fuel label next to filler cap on TRU fuel tank. Clean and degrease the surface before installing the label. HOW BACKPRESSURE CONTROLLER WORKS The backpressure controller measures when there is too much soot accumulated inside the FTF during low-speed TRU operation. When the controller measures 2.5 psi backpressure, it will force the TRU to run in high speed by energizing the speed solenoid for 10 minutes by putting +12V at the 7D solenoid terminal. Operating at high speed will regenerate and reduce the soot accumulated inside the FTF. After 10 minutes at high speed, the controller will return the TRU to low-speed operation. After 5 minutes at lowspeed operation, if the controller again detects a 2.5 psi backpressure, it will energize the high-speed solenoid for another 10 minutes. The controller will repeat this sequence until the soot is sufficiently reduced inside the FTF. No operator intervention is required for controller to function properly.

26 26 Installation CHECK PROPER OPERATION OF BACKPRESSURE CONTROLLER AFTER COMPLETING INSTALLATION TOOLS: Pliers, pressurizer 1) To test if controller is functioning correctly, temporarily remove silicone hose from the backpressure tube and connect hose to the pressurizer. 2) Reconnect positive battery cable. Start TRU and run in low speed. Squeeze pressurizer until yellow indicator line is in middle of green range on gauge. This will cause controller to shift TRU into high speed. If controller doesn t respond, see troubleshooting section on page 29. Remove pressurizer and reconnect silicone hose.

27 WARRANTY & CARB REGISTRATION CLEANING, ASH HANDLING 27 WARRANTY REGISTRATION and Installer s checklist After installation of the Proventia FTF system, register at and provide the following info to FTF distributor who will keep it for 4 years: TRU owner s name: TRU owner s contact phone number: TRU owner s Installer s name: Installer s contact phone number: Installer s Installation date: TRU hourmeter reading on installation date: hours TRU model name: (SBIII, Super II, Sentry): TRU unit serial number: TRU unit model year: TRU engine model: (Isuzu se2.2, Isuzu di2.2, Yanmar TK482, Yanmar TK486, etc.): TRU engine serial number: Proventia FTF serial number: Oil consumption: ounces/50 hours Injectors replaced at : hourmeter reading Installer initial that oil rate was measured and injectors were replaced CARB Identification Number (IDN) REGISTRATION After installing the Proventia FTF system, the TRU owner may apply for CARB IDN at: CLEANING THE FTF AND SAFE ASH-HANDLING GUIDELINES If there is excessive ash accumulation within the FTF (see page 30), the FTF will need to be cleaned. Clean the FTF by removing it from the TRU and blowing compressed air into the FTF outlet (seal around air hose), in the direction opposite of the exhaust flow. However, ash that would be blown out of the FTF inlet must be collected using a vacuum with a HEPA filter that collects the particulates for hazardous waste disposal. Call for recommendations of companies capable of removing ash from the FTF. Individuals who own, operate, or maintain diesel engines equipped with diesel particulate filters must manage hazardous ash waste generated by these devices. Follow ash-handling guidelines as prescribed by CARB at:

28 28 WIRING DIAGRAM FOR Backpressure ControlleR

29 TROUBLESHOOTING 29 TROUBLESHOOTING PROBLEM CAUSE SOLUTION TRU does not shift to high-speed mode when backpressure is 2.5 psi at lowspeed mode. Leak in backpressure fitting, backpressure tube, or silicone hose Faulty backpressure switch inside controller box #2 Wire is disconnected from starter solenoid terminal #7D Wire is disconnected from speed solenoid CH Wire is disconnected from speed solenoid Faulty timer module inside controller box Check for and repair leaks in the backpressure fitting, tube, or hose. Check if switch contacts close when pressure is greater than 2.5 psi. If not, replace switch. Terminal C on timer module should always be +12V. If not, check 5 amp in-line fuse on controller harness. Also, check for continuity of #2 wire from starter solenoid terminal up to C terminal on timer module. Put +12V on terminal #1 on timer module. 7D wire on speed solenoid should go to +12V for 10 minutes. If not, check for continuity of 7D wire from speed solenoid terminal up to NO terminal on timer module. Check if terminal #2 on timer module is grounded. If not, check for continuity of CH wire from speed solenoid terminal up to #2 terminal on timer module. Put +12V on terminal #1 on timer module. NO terminal on timer should go to +12V for 10 minutes. If not, replace timer module.

30 30 TROUBLESHOOTING PROBLEM CAUSE SOLUTION TRU repeatedly shifts to high speed for 10 minutes, then low speed for 5 minutes. Backpressure indicator gauge is in the red service range. Faulty Backpressure switch inside controller box Soot or ash accumulation inside of FTF Check if backpressure switch contacts are open when TRU is not running. If not, replace switch. If switch is okay, proceed to next section. Check if yellow gauge line in backpressure indicator gauge is within red service range during high-speed operation (see picture on page 4). If so, this is an indication that the FTF may have an excessive accumulation of soot or ash. The soot can be regenerated (cleaned out of the FTF) by running at high speed for 10 minutes and then shutting TRU off manually for 5 minutes. Repeat this cycle 5 times, then check backpressure indicator gauge reading again. If the yellow gauge line in backpressure indicator gauge continues to be within the red service range, this is an indication that the FTF may have an excessive accumulation of ash. Follow the filter cleaning and ash guidelines on page 27.

31 TROUBLESHOOTING 31 PROBLEM CAUSE SOLUTION Black smoke is visible from exhaust during steady speed operation Poor combustion Visible smoke is normal when TRU shifts from low- to highspeed operation or high- to low-speed operation. If black smoke is visible during steady speed operation, injectors need to be serviced or replaced. To service the TRU engine injectors, follow the TRU engine manufacturer guidelines: a. Check the injector spray pattern on a nozzle test stand. The injector spray pattern should have four good sprays with no dripping. b. Check the opening pressure of the nozzles: i. Yanmar injectors should be 2,800 to 3,000 psi. Isuzu injectors should be 2,633 to 2,704 psi. ii. Adjust nozzle opening pressure with shims as needed to meet the specification.

32 32 PARTS LIST PARTS LIST Replacement parts available at PART# F01548 T001 T002 T031 T004 DESCRIPTION FLOW THROUGH FILTER, FTF INSULATION WITH SNAPS INSULATION BLANKET, EXHAUST MANIFOLD FTF MOUNTING CLAMPS BACK PRESSURE INDICATOR GAUGE T033 FTF CONTROLLER ASSEMBLY (includes T014 & T015) T007A EXHAUST CLAMP, R45 T008 HOSE, 0.17 ID X 14 T009 T010 T011 T012 T013 T014 T015 TO17 T050 TEE FITTING, BRASS SPRING CLAMP FOR SILICONE HOSE BACKPRESSURE TUBE BACKPRESSURE FITTING ULSD FUEL LABEL BACKPRESSURE SWITCH TIMER MODULE PRESSURIZER DIODE ASSEMBLY

33 WARRANTY STATEMENTS 33 WARRANTY STATEMENTS YOUR WARRANTY RIGHTS AND OBLIGATIONS Proventia Americas, LLC will warrant the Proventia FTF for the Transport Refrigeration Unit (TRU) for which it is sold or leased to be free from defects in design, materials, workmanship, or operation of the Proventia FTF that cause the Proventia FTF to fail to conform to the emission control performance level the Proventia FTF was verified to, or to the other requirements of the California Code of Regulations Title 13CCR sections and 2710 for the period of 4 years, or 2,600 hours, whichever occurs first, provided there has been no abuse, neglect, or improper maintenance of the TRU, TRU engine, or Proventia FTF system, as specified in the owner s manuals. Where a warrantable condition exists, this warranty also covers the TRU engine from damage caused by the Proventia FTF system, subject to the same exclusions for abuse, neglect, or improper maintenance of the TRU or TRU engine. Please review the owners manuals for other warranty information. The Proventia FTF system may include a core part (e.g. particulate filter) as well as hoses, connectors, a backpressure monitor, and other emission-related assemblies. Where a warrantable condition exists, Proventia will repair or replace the FTF system at no cost to you including diagnosis, parts, and labor. WARRANTY COVERAGE For a TRU engine used in a TRU, the warranty period is 4 years or 2,600 hours of operation, whichever occurs first. If any emissions-related part of the Proventia FTF system is defective in design, materials, workmanship, or operation of the Proventia FTF system thus causing the Proventia FTF system to fail to conform to the emission control performance level it was verified to, or to the requirements in the California Code of Regulations Title 13CCR sections and 2710, within the warranty period, as defined above, Proventia Americas, LLC will repair or replace the Proventia FTF system, including parts and labor. In addition, Proventia Americas, LLC will replace or repair the TRU engine components to the condition they were in prior to the failure, including parts and labor, for damage to the TRU engine proximately caused by the Proventia

34 34 WARRANTY STATEMENTS FTF system. This also includes those relevant diagnostic expenses in the case in which a warranty claim is valid. Proventia Americas, LLC may, at its option, instead pay the fair market value of the TRU engine prior to the time the failure occurs. OWNER S WARRANTY RESPONSIBILITY As the TRU and Proventia FTF system owner, you are responsible for performing the required maintenance described in the TRU and Proventia FTF owners manuals. Proventia Americas, LLC recommends that you retain all maintenance records and receipts for maintenance expenses for your TRU and Proventia FTF system. If you do not keep your receipts or fail to perform all scheduled maintenance, Proventia Americas, LLC may have grounds to deny warranty coverage. You are responsible for presenting your TRU and Proventia FTF system to a Proventia Americas, LLC dealer as soon as a problem is detected. The warranty repair or replacement should be completed in a reasonable amount of time, not to exceed 30 days. If a replacement is needed, this may be extended to 90 days, should a replacement not be available, but must be performed as soon as a replacement becomes available. If you have questions regarding your warranty rights and responsibilities, contact Proventia Americas, LLC at or the California Air Resources Board at Stationary Source Division - TRU, 1001 I Street, Sacramento, CA 95814, (888) , or electronic mail: tru@arb.ca.gov The installer will furnish the Proventia FTF owner with a copy of the following statement: YOUR WARRANTY RIGHTS AND OBLIGATIONS (Installer s name) (Installer s phone number) will warrant that the installation of the Proventia FTF system is free from defects in workmanship or materials which cause the Proventia FTF to fail to conform to the emission control performance level it was verified to or to the requirements in the California Code of Regulations Title 13CCR sections The warranty period and the extent of the warranty coverage provided by the installer will be the same as the warranty provided by Proventia Americas, LLC, and the same exclusions apply.

35 WARRANTY STATEMENTS 35 OWNER S WARRANTY RESPONSIBILITY As the TRU owner and Proventia FTF system owner, you are responsible for presenting your TRU and Proventia FTF system to the installer as soon as a problem with the installation is detected. If you have questions regarding your warranty rights and responsibilities, you should contact the Installer of the Proventia FTF system or the California Air Resources Board at Stationary Source Division - TRU, 1001 I Street, Sacramento, CA 95814, (888) , or electronic mail: tru@arb.ca.gov

36 5/11/09

Owners Manual: Flow Through Filter (FTF) System

Owners Manual: Flow Through Filter (FTF) System PROVENTIA EMISSION CONTROL carb-verified, level 2+ tru Filter RETROFIT Owners Manual: Flow Through Filter (FTF) System Including Installation Guide for SB Model TRUs Proventia Americas, LLC c/o Proventia

More information

GreenTRAP Diesel Particulate Filter

GreenTRAP Diesel Particulate Filter Nett Technologies Inc. 2-6707 Goreway Drive, Mississauga, Ontario Canada L4V 1P7 tel: 905.672.5453 fax: 905.672.5949 e-mail: sales@nett.ca web: http://www.nett.ca GreenTRAP Diesel Particulate Filter V1.3

More information

CARB Compliance Solutions. Options for meeting the California Air Resources Board requirements for Transport Refrigeration Units.

CARB Compliance Solutions. Options for meeting the California Air Resources Board requirements for Transport Refrigeration Units. CARB Compliance Solutions Options for meeting the California Air Resources Board requirements for Transport Refrigeration Units. CARB - Are You Ready? The California Air Resource Board (CARB) has passed

More information

CARB VERIFIED DIESEL PARTICULATE FILTER OWNER S MANUAL

CARB VERIFIED DIESEL PARTICULATE FILTER OWNER S MANUAL CARB VERIFIED DIESEL PARTICULATE FILTER OWNER S MANUAL Ref. # OM0020908 pg. 1 OWNER S MANUAL State of California Warranty Information........................ 3 Product Description.............................................

More information

RYPOS DIESEL EXHAUST PARTICULATE FILTER DPF/ULETRU Carrier TRU. Manual Operation, Installation and Maintenance

RYPOS DIESEL EXHAUST PARTICULATE FILTER DPF/ULETRU Carrier TRU. Manual Operation, Installation and Maintenance RYPOS DIESEL EXHAUST PARTICULATE FILTER DPF/ULETRU Carrier TRU Manual Operation, Installation and Maintenance Page 1 YOUR RIGHT TO MAINTENANCE INFORMATION The Air Resources Board requires that Rypos Inc.

More information

RYPOS DIESEL EXHAUST PARTICULATE FILTER DPF/ULETRU Thermo-King TRU. Manual Operation, Installation and Maintenance

RYPOS DIESEL EXHAUST PARTICULATE FILTER DPF/ULETRU Thermo-King TRU. Manual Operation, Installation and Maintenance RYPOS DIESEL EXHAUST PARTICULATE FILTER DPF/ULETRU Thermo-King TRU Manual Operation, Installation and Maintenance Page 1 YOUR RIGHT TO MAINTENANCE INFORMATION The Air Resources Board requires that Rypos

More information

CARB Compliance Solutions. Options for meeting the California Air Resources Board requirements for Transport Refrigeration Units.

CARB Compliance Solutions. Options for meeting the California Air Resources Board requirements for Transport Refrigeration Units. CARB Compliance Solutions Options for meeting the California Air Resources Board requirements for Transport Refrigeration Units. CARB - Are You Ready? The California Air Resource Board (CARB) has passed

More information

Dodge 24v ISBe

Dodge 24v ISBe BD SUPER B 2003-2004 Dodge 24v ISBe (Non 600 motors) Part # 1045230 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION This turbo system is not compatible with an AFE intake system WITHOUT MODIFICATIONS.

More information

2004½-2007 Dodge 5.9L Cummins 24v ISBe (600 motors only)

2004½-2007 Dodge 5.9L Cummins 24v ISBe (600 motors only) 31 October 2006 Part # 1045235-1 - BD Supe r B Single 2004½-2007 Dodge 5.9L Cummins 24v ISBe (600 motors only) Part # 1045235 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. Note: This turbo system is

More information

EMISSION WARRANTIES FOR MTU ON-HIGHWAY APPLICATIONS

EMISSION WARRANTIES FOR MTU ON-HIGHWAY APPLICATIONS 2017 EMISSION WARRANTIES FOR MTU ON-HIGHWAY APPLICATIONS Page 1 of 7 1 FEDERAL EMISSION CONTROL WARRANTY STATEMENT 1.1 Emissions Warranty MTU America Inc. (MTU) warrants to the owner ( Owner ) of engines

More information

advanced FLOW engineering Instruction Manual P/N: Make: Chevrolet Model: Corvette Z06 (C7) Year: 2015 Engine: V8-6.

advanced FLOW engineering Instruction Manual P/N: Make: Chevrolet Model: Corvette Z06 (C7) Year: 2015 Engine: V8-6. advanced FLOW engineering Instruction Manual P/N: 52-74202 Make: Chevrolet Model: Corvette Z06 (C7) Year: 2015 Engine: V8-6.2L (sc) Please read the entire instruction manual before proceeding. Ensure all

More information

EMISSION WARRANTIES MS65022/02E

EMISSION WARRANTIES MS65022/02E EMISSION WARRANTIES MS65022/02E Printed in Germany 2015 Copyright MTU Friedrichshafen GmbH This Publication is protected by copyright and may not be used in any way whether in whole or in part without

More information

D28 V12 US Tier 2 / 3. Emission Warranty Off Road / Non Road Engines. MAN Engines

D28 V12 US Tier 2 / 3. Emission Warranty Off Road / Non Road Engines. MAN Engines D28 V12 US Tier 2 / 3 Emission Warranty Off Road / Non Road Engines MAN Engines Contents Introduction Emission Warranty.... 3 Emission Control System Warranty Statement Your Warranty Rights and Obligations...

More information

Emission Control Warranty Statement

Emission Control Warranty Statement Emission Control Warranty Statement Gas engine-generator sets MTU 10V0068 GS75 MTU 10V0068 GS100 MTU 10V0068 GS125 Built in North America MS65038/00E Table of Contents Table of Contents 1 Federal Emission

More information

advanced FLOW engineering Instruction Manual P/N: Make: Chevrolet Model: Corvette Z06 (C7) Year: Engine: V8-6.

advanced FLOW engineering Instruction Manual P/N: Make: Chevrolet Model: Corvette Z06 (C7) Year: Engine: V8-6. advanced FLOW engineering Instruction Manual P/N: 52-74202-1 Make: Chevrolet Model: Corvette Z06 (C7) Year: 2015-2017 Engine: V8-6.2L (sc) Please read the entire instruction manual before proceeding. Ensure

More information

LongMile -S. Owner s Manual

LongMile -S. Owner s Manual LongMile -S Owner s Manual The instructions, specifications, and recommendations in this manual are based on current information when this manual was released. ESW CleanTech, Inc. reserves the right to

More information

EMISSION CONTROL WARRANTY STATEMENT

EMISSION CONTROL WARRANTY STATEMENT EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The California Air Resources Board, U.S. EPA and Zenith Power Products LLC (ZPP) are pleased to explain the emission control system

More information

advanced FLOW engineering Instruction Manual P/N: Make: BMW Model: M3/M4 (F80/82/83) Year: Engine: L6-3.

advanced FLOW engineering Instruction Manual P/N: Make: BMW Model: M3/M4 (F80/82/83) Year: Engine: L6-3. advanced FLOW engineering Instruction Manual P/N: 52-76305 Make: BMW Model: M3/M4 (F80/82/83) Year: 2015-2016 Engine: L6-3.0L (tt) S55 Please read the entire instruction manual before proceeding. Ensure

More information

TOYOTA TUNDRA COLD AIR INTAKE Preparation SEQUOIA

TOYOTA TUNDRA COLD AIR INTAKE Preparation SEQUOIA Preparation SEQUOIA 2008 - Part Number: PTR03-34070 (5.7L) PTR03-34072 (4.7L) Kit Contents: 5.7L Item # Quantity Reqd. Description 1 1 Lid: Air Filter 2 1 Inlet Pipe: 5.7L 3 1 Air Filter: TRD Conical 4

More information

Installation and Instruction Manual. Cold Weather Starting Aid Part No A. Jet-Ex 4 Diesel Generator Sets

Installation and Instruction Manual. Cold Weather Starting Aid Part No A. Jet-Ex 4 Diesel Generator Sets TO-211 121890 Installation and Instruction Manual for Cold Weather Starting Aid Part No. 489782A For Use With Jet-Ex 4 Diesel Generator Sets HOBART BROTHERS COMPANY Ground Power Division Troy, Ohio 45373

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS THANK YOU FOR CHOOSING KURYAKYN! Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation,

More information

Operations & Maintenance Manual DFH-1000 DUCTLESS FUME HOOD

Operations & Maintenance Manual DFH-1000 DUCTLESS FUME HOOD Operations & Maintenance Manual DFH-1000 DUCTLESS FUME HOOD ----------------------------------------------------------------We Make Clean Air----------------------------------------------------------------

More information

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2004.5-2007 Dodge 5.9L Figure 1 - Full Kit Photo 25 Figure 2 - Hardware Kit Please read all instructions before installation. This kit is not emissions

More information

CARB Compliance Solutions. Options for meeting the California Air Resources Board requirements for Transport Refrigeration Units.

CARB Compliance Solutions. Options for meeting the California Air Resources Board requirements for Transport Refrigeration Units. CARB Compliance Solutions Options for meeting the California Air Resources Board requirements for Transport Refrigeration Units. CARB - Are You Ready? The California Air Resource Board (CARB) has passed

More information

INSTALLATION FORK MOUNTED DRIVING LIGHTS 5008

INSTALLATION FORK MOUNTED DRIVING LIGHTS 5008 5008 PARTS INCLUDED 1 Right Fork Mount Assembly 1 Left Fork Mount Assembly 2 H3 Driving Light Assemblies 1 12-Pin Wiring Adapter 1 Hardware Kit for Fork Mount Driving Lights, Including: 6 5/16-18 Nylock

More information

The Next Generation of Intakes advanced FLOW engineering. Instruction Manual P/N: E

The Next Generation of Intakes advanced FLOW engineering. Instruction Manual P/N: E The Next Generation of Intakes advanced FLOW engineering Instruction Manual P/N: 51-76105-E Make: Nissan Model: Titan XD Year: 2016 Engine: V8-5.0L (td) Cummins Please read the entire instruction manual

More information

Blue Air. Commercial Refrigeration Inc. Installation & Operation Manual Chef Bases

Blue Air. Commercial Refrigeration Inc. Installation & Operation Manual Chef Bases Blue Air Commercial Refrigeration Inc. Installation & Operation Manual Chef Bases Please read this manual completely before installing or operating this unit! BACB53 BACB71 BACB74 BACB83 BACB86 BACB96

More information

Installation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.

Installation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation. Installation Manual v1.0: Aurora Plus - 4000 Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: Aurora Plus - 4000 Kit Contents 1 Figure 2: Aurora Plus Hardware

More information

ONBOARD AIR HOOKUP KIT

ONBOARD AIR HOOKUP KIT ONBOARD AIR HOOKUP KIT PART NO. 20052 (30 amp - 110PSI on, 150PSI off) PART NO. 20053 (30 amp - 85PSI on, 105 PSI off) PART NO. 20055 (30 amp - 90 PSI on, 120 PSI off) IMPORTANT: It is essential that you

More information

Installation instructions

Installation instructions Installation instructions Akrapovič Exhaust System: Slip-On for the Porsche 911 Carrera (type 991) Porsche 911 Carrera S (type 991) Porsche 911 Carrera 4 (type 991) Porsche 911 Carrera 4S (type 991) Please

More information

A/C PRESSURE MONITOR INSTALLATION INSTRUCTIONS SYSTEM OPERATION GREEN INDICATOR LIGHT

A/C PRESSURE MONITOR INSTALLATION INSTRUCTIONS SYSTEM OPERATION GREEN INDICATOR LIGHT A/C PRESSURE MONITOR INSTALLATION INSTRUCTIONS Do not attempt to clean or inspect anything while the engine is running. Cleaning and inspection must be done by a certified mechanic. All A/C service must

More information

AEROMOTIVE Part # Mustang 5.0L Fuel System Kit INSTALLATION INSTRUCTIONS

AEROMOTIVE Part # Mustang 5.0L Fuel System Kit INSTALLATION INSTRUCTIONS AEROMOTIVE Part # 17103 83-93 Mustang 5.0L Fuel System Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend

More information

advanced FLOW engineering Instruction Manual P/N: Make: Ford Model: F-250/F-350/F-450/F-550 Year: Engine: V8-6.7L (td) Power Stroke

advanced FLOW engineering Instruction Manual P/N: Make: Ford Model: F-250/F-350/F-450/F-550 Year: Engine: V8-6.7L (td) Power Stroke advanced FLOW engineering Instruction Manual P/N: 77-43020 Make: Ford Model: F-250/F-350/F-450/F-550 Year: 2017-2018 Engine: V8-6.7L (td) Power Stroke Please read the entire instruction manual before proceeding.

More information

EVAP system, servicing

EVAP system, servicing Page 1 of 65 20-130 EVAP system, servicing EVAP system components 1 - Cap nut 10 Nm 2 - Cover 3 - Stud For EVAP canister 15 Nm 4 - Sealing piece 5 - Bleed line To EVAP canister purge regulator valve -

More information

Owner smanual. Banks TorqueTube System. Jeep 4.0L I-6 Models including: '00-06 Wrangler '00-01 Cherokee '99-01 Grand Cherokee

Owner smanual. Banks TorqueTube System. Jeep 4.0L I-6 Models including: '00-06 Wrangler '00-01 Cherokee '99-01 Grand Cherokee with Installation Instructions Owner smanual Banks TorqueTube System Jeep 4.0L I-6 Models including: '00-06 Wrangler '00-01 Cherokee '99-01 Grand Cherokee THIS MANUAL IS FOR USE WITH SYSTEM 51306 Gale

More information

CARB EO K-006-3* covers the following combination of parts when used on Harley-Davidson Touring Models (excluding Trikes)

CARB EO K-006-3* covers the following combination of parts when used on Harley-Davidson Touring Models (excluding Trikes) INSTALLATION INSTRUCTIONS: PART# 16894 POWER DUALS CTR CARB EO# K-006-3 COVERS USE ON 2014-2016 HARLEY-DAVIDSON TOURING MODELS (EXCEPT TRIKES) Congratulations, you have purchased the finest exhaust system

More information

advanced FLOW engineering Momentum GT Cold Air Intake System Instruction Manual P/N: /

advanced FLOW engineering Momentum GT Cold Air Intake System Instruction Manual P/N: / advanced FLOW engineering Momentum GT Cold Air Intake System Instruction Manual P/N: 51-72102 / 54-72102 Make: Dodge/RAM Model: 1500/1500 Classic Year: 2009-2019 Engine: V8-5.7L HEMI Please read the entire

More information

Installation & Operation Manual Chef Base

Installation & Operation Manual Chef Base Installation & Operation Manual Chef Base Please read this manual completely before installing or operating this unit! BACB53 BACB53M BACB71 BACB71M BACB74 BACB74M BACB83 BACB83M BACB86 BACB86M BACB96

More information

Thermo-Bob 1 Installation Manual: Kawasaki Concours

Thermo-Bob 1 Installation Manual: Kawasaki Concours Thermo-Bob 1 Installation Manual: 1986-2006 Kawasaki Concours This is a basic guide for installing the Thermo-Bob 1 on a Kawasaki ZG-1000 Concours. The bike used in the following photos was a 1995 year

More information

Owner smanual. Banks torquetube System. Jeep 4.0L I-6 models including: Wrangler Cherokee Grand Cherokee Comanche

Owner smanual. Banks torquetube System. Jeep 4.0L I-6 models including: Wrangler Cherokee Grand Cherokee Comanche Owner smanual with Installation Instructions Banks torquetube System Jeep 4.0L I-6 models including: 91-99 Wrangler 91-99 Cherokee 93-98 Grand Cherokee 91-92 Comanche THIS MANUAL IS FOR USE WITH SYSTEM

More information

Owner s Manual Supplement. Liquefied Petroleum Gas (LPG) Fuel System for 1998 GM Medium Duty Chassis (C-60/C-70) with 6.0L and 7.

Owner s Manual Supplement. Liquefied Petroleum Gas (LPG) Fuel System for 1998 GM Medium Duty Chassis (C-60/C-70) with 6.0L and 7. Owner s Manual Supplement Liquefied Petroleum Gas (LPG) Fuel System for 1998 GM Medium Duty Chassis (C-60/C-70) with 6.0L and 7.0L V8 OWNERS MANUAL SUPPLEMENT Table of Contents Refueling Your Vehicle...1

More information

advanced FLOW engineering Instruction Manual P/N: TA-3016P

advanced FLOW engineering Instruction Manual P/N: TA-3016P advanced FLOW engineering Instruction Manual P/N: TA-3016P Make: Infiniti Model: G37 Coupe Year: 2008-2013 Engine: V6-3.7L Make: Infiniti Model: Q60 Year: 2014 Engine: V6-3.7L (EO Exempt 2008-2013 only)

More information

HEAVY DUTY ONBOARD AIR SYSTEM PART NO

HEAVY DUTY ONBOARD AIR SYSTEM PART NO IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product. SAVE THIS MANUAL FOR FUTURE REFERENCE

More information

Emission Control System Warranty Statement

Emission Control System Warranty Statement Emission Control System Warranty Statement Marine and industrial diesel engines Supplement to Operator s Manual (USA) Marine engines This Emission Control System Warranty Statement applies only to engines

More information

Safety, Installation and Service Manual Models 1952, 1953 & 1972

Safety, Installation and Service Manual Models 1952, 1953 & 1972 Ultraviolet Germicidal Lamps Model 1952 24 Rooftop Unit Model 1953 32 Rooftop Unit Model 1972 Rooftop Unit, Internal Mount Safety, Installation and Service Manual Models 1952, 1953 & 1972 READ AND SAVE

More information

TOYOTA 4RUNNER COLD AIR INTAKE FJ CRUISER Preparation

TOYOTA 4RUNNER COLD AIR INTAKE FJ CRUISER Preparation Preparation Part Number: PTR03-89100 Kit Contents Item # Quantity Reqd. Description 1 1 Air Filter (P/N: PTR43-00083) 2 1 Upper Air Box 3 1 Lower Air Box 4 1 Hump Coupler 5 1 Throttle Body Coupler 6 1

More information

Procharger Stage II Intercooled Supercharger System (11-14 GT)

Procharger Stage II Intercooled Supercharger System (11-14 GT) Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8203 2003-2005 Dodge Ram 5.7L V8 CARB EO # D-392-28 2005 Dodge Powerwagon Hemi CARB EO # D-392-28 Brute Force Intake Systems that are

More information

INSTALLATION INSTRUCTIONS: HARLEY-DAVIDSON SPORTSTER MINI GRENADES PART# / 46874

INSTALLATION INSTRUCTIONS: HARLEY-DAVIDSON SPORTSTER MINI GRENADES PART# / 46874 INSTALLATION INSTRUCTIONS: HARLEY-DAVIDSON SPORTSTER MINI GRENADES PART# 16874 / 46874 Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your Vance & Hines exhaust

More information

The Next Generation. of Intakes. advanced FLOW engineering Momentum Air Intake. Instruction Manual P/N: E

The Next Generation. of Intakes. advanced FLOW engineering Momentum Air Intake. Instruction Manual P/N: E The Next Generation advanced FLOW engineering Momentum Air Intake Instruction Manual P/N: 51-72005-E Make: RAM Model: 2500/3500 HD Year: 2013-2018 Engine: L6-6.7L (td) of Intakes Please read the entire

More information

Users Manual Certified Series Direct Drive Pump 1-7 LPM

Users Manual Certified Series Direct Drive Pump 1-7 LPM Users Manual Certified Series Direct Drive Pump 1-7 LPM Safety, Operating, Installation, and Maintenance Instructions 600 S 56 th Street #9 Chandler, AZ 85226 Phone: 480-507-6478 Fax: 480-838-2232 www.fogco.com

More information

Owner smanual. Banks TorqueTube System. Jeep 2.5L 4-Cylinder '91-02 Wrangler. with Installation Instructions THIS MANUAL IS FOR USE WITH SYSTEM 51316

Owner smanual. Banks TorqueTube System. Jeep 2.5L 4-Cylinder '91-02 Wrangler. with Installation Instructions THIS MANUAL IS FOR USE WITH SYSTEM 51316 with Installation Instructions Owner smanual Banks TorqueTube System Jeep 2.5L 4-Cylinder '91-02 Wrangler THIS MANUAL IS FOR USE WITH SYSTEM 51316 Gale Banks Engineering 546 Duggan Avenue Azusa, CA 91702

More information

Installation Instructions

Installation Instructions 2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com

More information

I N S TA L L AT I O N

I N S TA L L AT I O N I N S TA L L AT I O N 5008 fits: H-D: '80-Up Electra glide, tour glide, road king, road glide or street glide PartS Included 1 Right Fork Mount Assembly 1 Left Fork Mount Assembly 2 H3 Driving Light Assemblies

More information

advanced FLOW engineering Instruction Manual P/N: /

advanced FLOW engineering Instruction Manual P/N: / advanced FLOW engineering Instruction Manual P/N: 54-12162 / 51-12162 Make: Dodge/Chrysler Model: Challenger/Charger/300C Year: 11-17 Engine: V8-5.7L HEMI Please read the entire instruction manual before

More information

AEROMOTIVE Part # L Ford F L Ford Expedition L Ford F-250 Super Duty INSTALLATION INSTRUCTIONS

AEROMOTIVE Part # L Ford F L Ford Expedition L Ford F-250 Super Duty INSTALLATION INSTRUCTIONS AEROMOTIVE Part # 14118 97-03 5.4L Ford F-150 97-02 5.4L Ford Expedition 98-03 5.4L Ford F-250 Super Duty INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of

More information

AEROMOTIVE Part # INSTALLATION INSTRUCTIONS

AEROMOTIVE Part # INSTALLATION INSTRUCTIONS AEROMOTIVE Part # 14102 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried

More information

INSTALLATION INSTRUCTIONS: P/N: / D INSTALLATION INSTRUCTIONS:

INSTALLATION INSTRUCTIONS: P/N: / D INSTALLATION INSTRUCTIONS: INSTALLATION INSTRUCTIONS: INSTALLATION INSTRUCTIONS: P/N: 75-5115 / 75-5115D 15461 SLOVER AVE., FONTANA, CA 92337 PH: 909.947.0015, FAX: 909.947.0603 WWW.SBFILTERS.COM Thank You! for purchasing your new

More information

These instructions were written for reference only and the use of a factory service manual is recommended.

These instructions were written for reference only and the use of a factory service manual is recommended. Introducing the CorkSport High Pressure Fuel Line designed for the MZR DISI. This fuel line is designed to replace the OEM fuel line which are prone to failure at the brazed connection at the rail. The

More information

advanced FLOW engineering Instruction Manual P/N: / / /

advanced FLOW engineering Instruction Manual P/N: / / / advanced FLOW engineering Instruction Manual P/N: 55-12550 / 55-12551 / 55-12540 /55-12541 Make: Toyota Model: Tundra Year: 2007-2017 Engine: V8-4.6L/5.7L Please read the entire instruction manual before

More information

Model AM2 M40 Panel Installation, Operation, and Maintenance Manual

Model AM2 M40 Panel Installation, Operation, and Maintenance Manual Model AM2 M40 Panel Installation, Operation, and Maintenance Manual RECEIVING AND INSPECTION Upon receiving unit, check for any interior and exterior damage, and if found, report it immediately to the

More information

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY CAUTION: INSTALLATION LOCATION:

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY CAUTION: INSTALLATION LOCATION: 2 Please read the safety and installation instructions carefully to help ensure a correct and SAFE installation of your Second Wind Ultraviolet Germicidal Photo-catalytic Air Purifier. WARNING: FAILURE

More information

Horizon. Owner s Manual. ATTENTION: Keep a copy of this Owner s Manual in the vehicle at all times.

Horizon. Owner s Manual. ATTENTION: Keep a copy of this Owner s Manual in the vehicle at all times. Horizon Owner s Manual ATTENTION: Keep a copy of this Owner s Manual in the vehicle at all times. The instructions, specifications, and recommendations in this manual are based on current information when

More information

6.0L HARD START / LONG CRANK / NO START TSB LOW INJECTOR CONTROL PRESSURE (ICP)

6.0L HARD START / LONG CRANK / NO START TSB LOW INJECTOR CONTROL PRESSURE (ICP) 6.0L HARD START / LONG CRANK / NO START TSB 08-18-6 LOW INJECTOR CONTROL PRESSURE (ICP) FORD: 2005 Excursion 2005-2007 F-Super Duty 2005-2008 E-350, E-450 This article supersedes TSBs 08-9-9 and 05-12-3

More information

advanced FLOW engineering Instruction Manual P/N: /

advanced FLOW engineering Instruction Manual P/N: / advanced FLOW engineering Instruction Manual P/N: 51-74108 / 54-74108 Make: Chevrolet / GMC Model: 2500HD/3500HD Year: 2016-2017 Engine: V8-6.0L w/ Mech. Fan Please read the entire instruction manual before

More information

V8-4.7L (C.A.R.B D /20)

V8-4.7L (C.A.R.B D /20) advanced FLOW engineering Instruction Manual P/N: 51-12262-1 / 54-12262-1 Make: Toyota Model: Tundra Year: 2000-2004 Engine: V8-4.7L Make: Toyota Model: Sequoia Year: 2001-2004 Engine: V8-4.7L (C.A.R.B

More information

INSTALLATION INSTRUCTIONS: P/N: / D INSTALLATION INSTRUCTIONS:

INSTALLATION INSTRUCTIONS: P/N: / D INSTALLATION INSTRUCTIONS: INSTALLATION INSTRUCTIONS: INSTALLATION INSTRUCTIONS: P/N: 75-5115 / 75-5115D 15461 SLOVER AVE., FONTANA, CA 92337 PH: 909.947.0015, FAX: 909.947.0603 WWW.SBFILTERS.COM Thank You! for purchasing your new

More information

USB Charge Port Installation Instructions

USB Charge Port Installation Instructions USB Charge Port Installation Instructions Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0014C Thank you for purchasing a Logo Lites USB Charge Port! USB Charge

More information

Installation instructions

Installation instructions Installation instructions Akrapovič Exhaust System: Slip-On for the ABARTH 500 ABARTH 500C www.akrapovic.com Installation instructions Akrapovič Exhaust System: Slip-On for the ABARTH 500 ABARTH 500C

More information

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 6.7L

Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 6.7L 04/05/2012 Dodge 2010-2011 6.7L Twin CP3 701-900-2356-INST Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2010-2011 Dodge 6.7L Figure 1 - Full Kit Photo 29 Figure 2 - Hardware Kit (800) 949-60002

More information

MODEL NUMBER: MEDIUM DUTY ONBOARD AIR SYSTEM

MODEL NUMBER: MEDIUM DUTY ONBOARD AIR SYSTEM MODEL NUMBER: 10003 MEDIUM DUTY ONBOARD AIR SYSTEM IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using

More information

Owner smanual. Banks TorqueTube System With Optional Headpipe Assembly

Owner smanual. Banks TorqueTube System With Optional Headpipe Assembly Owner smanual with Installation Instructions Banks TorqueTube System With Optional Headpipe Assembly Jeep 4.0L I-6 models including: 91-99 Wrangler 91-99 Cherokee 93-98 Grand Cherokee 91-92 Comanche THIS

More information

Holley High Performance Intake System* For Port 13B Engines (Includes B 6-Port engines converted to 4-Port)

Holley High Performance Intake System* For Port 13B Engines (Includes B 6-Port engines converted to 4-Port) Holley High Performance Intake System* For 1974-1978 4-Port 13B Engines (Includes 1984-85 13B 6-Port engines converted to 4-Port) Installation Instructions I-18038 Note: These instructions assume: The

More information

SCION xb PERFORMANCE AIR INTAKE Section I Installation Preparation 2.4L I-4

SCION xb PERFORMANCE AIR INTAKE Section I Installation Preparation 2.4L I-4 Section I Installation Preparation 2.4L I-4 Part Number(s): PTR03-52110 Kit Contents Item # Quantity Description Reqd. 1 1 TRD Inlet Tube 2 1 TRD Upper Air Box with HC Trap 3 1 Hump Hose Coupler 4 1 Hump

More information

Twin Turbo Installation Instructions

Twin Turbo Installation Instructions Twin Turbo Installation Instructions Pacific Performance Engineering 303 N Placentia Ave. Fullerton, CA 92831 www.ppediesel.com Legal in California only for racing vehicles which may never be used on the

More information

Rotated Tuner Kit for Garrett GT Turbos

Rotated Tuner Kit for Garrett GT Turbos Rotated Tuner Kit for Garrett GT Turbos 031411 Thank you for purchasing the PERRIN performance rotated turbo kit. Installation of this turbo should only be performed by persons experienced in the installation

More information

GROUP 13C 13C-1 CONTENTS GENERAL DESCRIPTION... 13C-2 FUEL TANK... 13C-11 FUEL SUPPLY DIAGNOSIS... 13C-3 SPECIAL TOOLS... 13C-8

GROUP 13C 13C-1 CONTENTS GENERAL DESCRIPTION... 13C-2 FUEL TANK... 13C-11 FUEL SUPPLY DIAGNOSIS... 13C-3 SPECIAL TOOLS... 13C-8 13C-1 GROUP 13C CONTENTS GENERAL DESCRIPTION......... 13C-2 DIAGNOSIS....... 13C-3 INTRODUCTION TO DIAGNOSIS........................ 13C-3 TROUBOLESHOOTING STRATEGY..... 13C-3 SYMPTOM CHART...................

More information

Part number SP Mitsubishi EVO X 2.0L 4 cyl. 1 pc. air intake system equipped

Part number SP Mitsubishi EVO X 2.0L 4 cyl. 1 pc. air intake system equipped Part number SP1899 2008 Mitsubishi EVO X 2.0L 4 cyl. 1 pc. air intake system equipped with MR Tech and Air Fusion 2 pc. upper intercooler piping 1- EVO X heat shield (#11020) 1-3 1/2 Power-Flow filter

More information

Light Duty Electronic Air Command

Light Duty Electronic Air Command 2491 PSI BAR Light Duty Electronic Air Command INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Light Duty Electronic Air Command kit. This kit was designed to provide inflation control

More information

Typical Install Instructions

Typical Install Instructions Typical Install Instructions Read & understand all steps of these instructions before beginning this installation. WEBER Conversion Kit, VW T-1/2, up to 1835cc 32 / 36 DFEV Weber Carburetor These instructions

More information

INSTALLATION BLIND SPOT TURN SIGNAL MIRRORS 1457

INSTALLATION BLIND SPOT TURN SIGNAL MIRRORS 1457 BLIND SPOT TURN SIGNAL MIRRORS 1457 PARTS INCLUDED 2 Blind Spot Turn Signal Mirror Assemblies 1 Wire Harness Kit Including: 2 Wiring Harness (four pin) 1 Adapter Harness (six pin) 2 3-Pin Female Connectors

More information

advanced FLOW engineering Instruction Manual P/N: / / /

advanced FLOW engineering Instruction Manual P/N: / / / advanced FLOW engineering Instruction Manual P/N: 55-12550 / 55-12551 / 55-12540 /55-12541 Make: Toyota Model: Tundra Year: 2007-2017 Engine: V8-4.6L/5.7L Please read the entire instruction manual before

More information

Read all instructions carefully before attempting installation. 1633S-1JS Shown. Rev DSL

Read all instructions carefully before attempting installation. 1633S-1JS Shown. Rev DSL Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions and Warranty Information 1630S 86-87 Ranger/Bronco II

More information

advanced FLOW engineering Stage-2 Air Intake Instruction Manual P/N: / /

advanced FLOW engineering Stage-2 Air Intake Instruction Manual P/N: / / advanced FLOW engineering Stage-2 Air Intake Instruction Manual P/N: 51-12322-1/54-12322-1/75-12322-1 Make: GM Model: Silverado HD/Sierra HD Year: 2011-2016 Engine: V8-6.6L (td) LML Please read the entire

More information

advanced FLOW engineering Instruction Manual P/N:

advanced FLOW engineering Instruction Manual P/N: advanced FLOW engineering Instruction Manual P/N: 77-46205 Make: Jeep Model: Wrangler (JK) Year: 2012-2018 Engine: V6-3.6L Make: Jeep Model: Wrangler (JL) Year: 2018-2019 Engine: V6-3.6L Please read the

More information

2019 EMISSION WARRANTIES BiFuel Kit

2019 EMISSION WARRANTIES BiFuel Kit 2019 EMISSION WARRANTIES BiFuel Kit MS65050/02E Printed in Germany 2019 Copyright MTU Friedrichshafen GmbH This Publication is protected by copyright and may not be used in any way whether in whole or

More information

advanced FLOW engineering Instruction Manual P/N: / / Make: Toyota Model: Tacoma Year: Engine: V6-4.

advanced FLOW engineering Instruction Manual P/N: / / Make: Toyota Model: Tacoma Year: Engine: V6-4. advanced FLOW engineering Instruction Manual P/N: 51-76012 / 54-76012 / 75-76012 Make: Toyota Model: Tacoma Year: 2012-2015 Engine: V6-4.0L Please read the entire instruction manual before proceeding.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2807 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY -6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This

More information

Utility Controller Hand Air Operated

Utility Controller Hand Air Operated Utility Controller Hand Air Operated P-1395 819-0288 Installation Instructions Introduction The Warner Electric air/manual Utility Controller combines manual and automatic (air) actuation for the operation

More information

Harley Davidson FL Touring Current Xtreme

Harley Davidson FL Touring Current Xtreme ITEMS SUPPLIED Description Part # Qty Front Header (Chr/Blk) 100-0119/100-0123 1 Rear Header (Chr/Blk) 100-0120/100-0124 1 Front Heat Shield (Chr/Blk) 100-0121/100-0125 1 Rear Heat Shield (Chr/Blk) 100-0122/100-0126

More information

advanced FLOW engineering Instruction Manual P/N: / Make: BMW Model: 328d/dx (F30/F31) Year: Engine: L4-2.

advanced FLOW engineering Instruction Manual P/N: / Make: BMW Model: 328d/dx (F30/F31) Year: Engine: L4-2. advanced FLOW engineering Instruction Manual P/N: 51-76307 / 54-76307 Make: BMW Model: 328d/dx (F30/F31) Year: 2014-2016 Engine: L4-2.0L (td) N47 Please read the entire instruction manual before proceeding.

More information

Reach ins, Freeezers & Refrigerators Installation & Operation Manual

Reach ins, Freeezers & Refrigerators Installation & Operation Manual Reach ins, Freeezers & Refrigerators Installation & Operation Manual BSR23 BSF23 BSR49 BSF49 BSR72 BSF72 IMPORTANT SAFETY INSTRUCTIONS (SAVE THESE INSTRUCTIONS) Visit us on the web at www.blueairinc.com

More information

3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B

3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B 3 October 2016 PN#1045320 24V Dodge Twin Turbo Kit (I-00274) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Twin Turbo Kit 1998½- 2 0 0 2 D o d g e 2 4 v I S B Part# 1045320 PLEASE READ

More information

Xtreme Air Command. Step 1 Prepare the components. Step 2 Select a mounting location. Parts list

Xtreme Air Command. Step 1 Prepare the components. Step 2 Select a mounting location. Parts list 2549 60 90 400 600 30 200 120 800 psi 1000 kpa PSI 0 150 Xtreme Air Command Installation instructions Congratulations on your purchase of a new Xtreme Air Command kit. This kit was designed to provide

More information

AIR CONTROL ACCESSORY KIT

AIR CONTROL ACCESSORY KIT RAPID RESPONSE SYSTEM 2283 AIR CONTROL ACCESSORY KIT INSTALLATION INSTRUCTIONS Congratulations on your purchase of a new Air Control Accessory Kit. This kit was designed to provide inflation control of

More information

EyeMax TECHNICAL MANUAL. Technology, LLC FOR UPDATED INFORMATION, VISIT TABLE OF CONTENTS

EyeMax TECHNICAL MANUAL. Technology, LLC FOR UPDATED INFORMATION, VISIT   TABLE OF CONTENTS REV 0 US and Foreign Patents: 6540909, 6841065, 7150824, 5507942, RE37165, 234242 L4814 Fuel Pro 482 Technical Manual. Technology, LLC TABLE OF CONTENTS How it Works............. 1 Typical Installation...........

More information

AEROMOTIVE Part # Ford 5.4L GT500 Shelby Mustang Fuel Rail Kit INSTALLATION INSTRUCTIONS

AEROMOTIVE Part # Ford 5.4L GT500 Shelby Mustang Fuel Rail Kit INSTALLATION INSTRUCTIONS AEROMOTIVE Part # 14145 07 Ford 5.4L GT500 Shelby Mustang Fuel Rail Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures.

More information

advanced FLOW engineering Momentum Air Intake Instruction Manual P/N: /

advanced FLOW engineering Momentum Air Intake Instruction Manual P/N: / advanced FLOW engineering Momentum Air Intake Instruction Manual P/N: 51-76206-1 / 54-76206-1 Make: Jeep Model: Grand Cherokee (WK2) SRT-8/SRT Year: 2012-2017 Engine: V8-6.4L HEMI Please read the entire

More information

AEROMOTIVE Part # Subaru Fuel Rails for Top Feed Injectors WRX & STI INSTALLATION INSTRUCTIONS

AEROMOTIVE Part # Subaru Fuel Rails for Top Feed Injectors WRX & STI INSTALLATION INSTRUCTIONS AEROMOTIVE Part # 14135 Subaru Fuel Rails for Top Feed Injectors 02-14 WRX & 07-14 STI INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 28 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY 2-5 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This

More information