Data sheet: Wilo-VeroLine-IPH-W 65/ /4

Transcription

1 Data sheet: Wilo-VeroLine-IPH-W 65/1-1.1/ Pump curves v,5 1, 1,5,,5 65/16 1,1/ [m/s] Wilo-VeroLine IPH-O / IPH-W 65/16-65/15 Approved fluids (other fluids on request) Heating water (in accordance with VDI 35) Water-glycol mixtures (for - vol.% glycol and fluid temperature C) 65/1 1,1/ 5 Cooling and cold water H [m] 65/15 1,1/ Heat transfer oil P [ kw ] [m 3/h] [l/s],6,5,,3,,1 NPSH Q NPSH [m] [lgpm] Permitted field of application Standard version for operating pressure p max Temperature range at max. ambient temperature + C Max. ambient temperature + C Installation in closed buildings Pipe connections Nominal flange diameter DN 65 Hot water: 3 bar C [m 3/h] Flanges (according to EN 19-) PN 5 Dimension drawing 511, Flange with pressure-measurement connections Materials 19 Pump housing 1.65 Lantern EN-GJS--15 Impeller EN-GJL-5 Pump shaft 1.5 [AISI16] Terminal diagram W U V W U V L L 1 L3 PE L L 1 L3 PE : Connection diagram delta connection Y: Connection diagram star connection Motor protection switch required onsite. Check the direction of rotation! To change the direction of rotation, exchange any two phases. Mechanical seal AQ1EGG Other mechanical seals On request Electrical connection Mains connection 3~ V, 5 Hz Nominal speed n 115 rpm Motor/electronics After removing the bridges, Y- start is possible. Integrated full motor protection Special version with PTC thermistor sensor (KLF) at additional charge Protection class IP 55 Insulation class F Efficiency η M.8 Power factor Motor winding up to 3 kw cos φ.81 3 V Δ/ V Y, 5 Hz Subject to change without prior notice. 5 Hz 15-1 / 7

2 Data sheet: Wilo-VeroLine-IPH-W 65/1-1.1/ Motor winding from kw 3 V Δ/ V Y, 5 Hz Installation options Pipe installation ( 15 kw motor power) Support-bracket mounting with horizontal shaft only Information for order placements Weight approx. m. kg Make Wilo Type VeroLine-IPH-W 65/1-1.1/ Art no Observe motor name plate data Subject to change without prior notice. 5 Hz 15- / 7

3 Dimensions and dimension drawings: Wilo-VeroLine-IPH-W 65/1-1.1/ Dimension drawing 511, Subject to change without prior notice. 5 Hz 15-3 / 7

4 Pump curves: Wilo-VeroLine-IPH-W 65/1-1.1/ Pump curves v,5 1, 1,5,,5 [m/s] /16 1,1/ Wilo-VeroLine IPH-O / IPH-W 65/16-65/15 6 H [m] 5 65/1 1,1/ 65/15 1,1/ 3 1 NPSH [m /h] [l/s] NPSH [m], Q [lgpm],5 P [ kw ],,3,, [m 3/h] Subject to change without prior notice. 5 Hz 15- / 7

5 Ordering information: Wilo-VeroLine-IPH-W 65/1-1.1/ Information for order placements Make Wilo Type VeroLine-IPH-W 65/1-1.1/ Art no EAN number Colour Silver Minimum order quantity 1 Minimum order quantity unit PCE Weight (net) kg. Length (net) mm 53.5 Width (net) mm 8 Height (net) mm Weight (gross) kg 6.6 Length (gross) mm 78 Width (gross) mm 38 Height (gross) mm 5 Packaging type Cardboard box Subject to change without prior notice. 5 Hz 15-5 / 7

6 Specification texts: Wilo-VeroLine-IPH-W 65/1-1.1/ Single-stage glanded centrifugal pump with in-line design for operating conditions with especially hot fluids. Three-phase motor with one-piece shaft and special distance lantern for accommodating a cooling rib housing for the mechanical shaft seal. This series is suitable for pipe installation with horizontal motor/pump shaft. Materials Pump housing: 1.65 Lantern: EN-GJS--15 Impeller: EN-GJL-5 Pump shaft: 1.5 [AISI16] Mechanical seal: AQ1EGG Permitted field of application Standard version for operating pressure: Hot water: 3 bar Temperature range at max. ambient temperature + C: C Max. ambient temperature: + C Pipe connections Nominal flange diameter: DN 65 Flanges (according to EN 19-): PN 5 Flange with pressure-measurement connections: Dimensions: 51 mm Motor/electronics Protection class: IP 55 Insulation class: F Motor efficiency:././. % Power factor:.81 Nominal speed: 115 rpm Weight Weight approx.: kg Information for order placements Art no.: 1575 Type: VeroLine-IPH-W 65/1-1.1/ Make: Wilo Subject to change without prior notice. 5 Hz 15-6 / 7

7 Terminal diagram : Wilo-VeroLine-IPH-W 65/1-1.1/ Terminal diagram W U V W U V : Connection diagram delta connection Y: Connection diagram star connection Motor protection switch required onsite. Check the direction of rotation! To change the direction of rotation, exchange any two phases. After removing the bridges, Y- start is possible. L L 1 L3 PE L L 1 L3 PE Subject to change without prior notice. 5 Hz 15-7 / 7