GE Industrial Solutions. Limitamp * AR. Arc Resistant Medium Voltage Motor Control. Application Guide
|
|
- Sherilyn French
- 6 years ago
- Views:
Transcription
1 Industrial Solutions Limitamp AR Arc Resistant edium Voltage otor ontrol Application uide
2 Limitamp AR - Arc Resistant Introduction Limitamp AR is the Arc Resistant version of the Limitamp, providing a solution for flash conditions, increasing the safety and protection defined in the applicable I standards. The new Limitamp AR edium Voltage otor ontrollers meet the safety requirements of the market, offering more reliable operation and control of edium Voltage installations. This new construction includes a complete product offering of 00A/00A starters and other controllers. The Limitamp AR is designed to provide a reliable solution to the growing demand for Arc Resistant equipment in the market place. The uniquely designed Limitamp AR products have passed a rigorous testing program as specified by the I/ASI Type safety standard. They are designed to provide personnel protection on the front, rear and sides of the enclosure in the event of an arc flash occurrence. This means that when the medium voltage doors are properly secured, the service technician can access the interior of the low voltage compartment, and the Limitamp AR provides the protection from a potential arc flash event. Limitamp AR keeps the same basic design, features and general applications of the R1 Limitamp control and the vacuum contactor, meeting U and all other requirements. Technical ata System voltage: up to.kv ain bus: 100A, 000A, 000A 50kA short circuit at 0.5 seconds nclosure type: Indoor A 1 gasketed Arc Resistant Type per I/ASI standard Front view Limitamp AR roduct Offering 1-high and -high 00A FVR (full voltage non-reversing starters) 1-high 00A FVR (full voltage non-reversing starters) 1-high 00A FVR (full voltage reversing starters) 1-high 00A FVR (full voltage reversing starters) RVAT (reduced voltage autotransformer starters) RVR (reduced voltage primary reactor starters) S1W (two speed, single winding starters) SW (two speed, dual winding starters) 00A VSS (medium voltage solid-state starters) I-10 load break switches SY excitation starters ain, Feeder and Tie sections Incoming line cable sections Auxiliary sections -igh Limitamp AR with medium voltage door open
3 onstruction The low voltage door on the front of each unit includes pilot lights, switches and relays. This compartment provides easy access to the secondary devices while the main medium voltage front door is closed. It is isolated from the live parts of the unit, providing increased safety under arc flash conditions. In the case of an internal arc fault inside the vertical section, all the gases and other materials produced as result of the fault are directed to the upper part of the vertical section. The robust design of the enclosure, and medium voltage doors prevents front, bottom and side exhaust. articles and gases are directed to the upper part of the vertical section, through the vent flaps and plenum to an external area determined by the customer, away from the gear and personnel. very vertical section includes a plenum fabricated of thick (1 gauge) sheet steel, and along with others in adjacent sections, form a duct along the top of the Limitamp AR. etail of low voltage compartment when medium voltage door is closed The plenum system is not installed at the factory. It is supplied for field installation. xtra segments can be ordered, depending on the particular characteristics of the installation site. The last segment of the duct is provided with a cap to direct the arc flash particles and gases away from the gear and the operator. -igh Limitamp AR with low voltage door open When the main door is open, an extra glass-reinforced polyester barrier is provided in the back of the low voltage compartment for protection, as shown in photo below. Arc uct / lenum showing exhaust cap at the last segment. ach cubicle is provided with reinforced doors that incorporate special hinges, gaskets, handles and latches to ensure proper sealing in front of the section. The Limitamp AR Arc Resistant edium Voltage otor ontrols are manufactured using heavy duty reinforced side panels in a 1/ thick (11 gauge) welded steel construction which, in conjunction with other mechanical features and special bolted pieces provide additional safety for arc flash conditions. Front view Limitamp -igh with extension main bus and extension of the duct/plenum Rear of low voltage box with medium voltage door open Special lock system in the medium voltage door to ensure protection
4 Limitamp AR edium Votage otor ontrol R1 AR 00A, Stationary or raw-out, Outline imensions Volts, One-igh, ottom able ntry. 1 igh, Wide. Limitamp Limitamp AR AR edium edium Voltage Voltage otor otor ontrol ontrol nclosures nclosures nclosure Outline dimensions Volts nclosure Outline dimensions Volts R1 AR 00A, 1 igh, 0" Wide -100 lbs R1 AR 00A, 1 igh, 0" Wide 1 Kg (Stationary or raw-out) L..SI T AL TRY (Stationary or raw-out) AL TRY T AL TRY I. LA TO Limitamp AR. edium Voltage otor ontrol nclosures nclosure Outline dimensions Volts R1 AR 00A, 1 igh, 0" Wide. (Stationary or raw-out) T AL TRY TO LOOR LA.. 1 igh, 0 Wide 1 1 L..SI L..SI lbs -000 lbs0 Kg 0 Kg T AL TRY T AL TRY otes: Incoming ower Terminal onnection 1 A ower us ontrol Lead Terminal oard otor Lead Terminal onnection round us Terminal onnection F round Terminal onnection (If Ordered) Space Required to Open oors 15 Four-foot Aisle for ontactor Removal ounting oles for 1/" iameter Anchor olts Recommended osition for Incoming otor onduit UR UIT TO UR UIT TO add for welded -000 lbs -. 0 Kg -. L..SI T AL TRY otes: Incoming ower Terminal onnection 1-I 1-I 1 A ower us ontrol Lead Terminal oard otor Lead Terminal onnection LA LA round us Terminal onnection F round Terminal onnection (If Ordered) Space Required to Open oors 15 Four-foot Aisle for ontactor Removal ounting oles for 1/" iameter Anchor olts Recommended osition for Incoming otor onduit Recommended osition for Incoming ontrol onduit Indicates Terminal Location - Approximate for able Length - 1-I UR U 0.0
5 Limitamp AR edium Votage otor ontrol 1 1-I A ower us R1 AR 00A, -000 lbs Stationary or raw-out, Kg Outline imensions L..SI Volts, One-igh, Top able ntry otes: Incoming ower 1 igh, Terminal Wide onnection 1 A ower us ontrol Lead Terminal oard otor Lead Terminal onnection round us Terminal onnection F round Terminal onnection (If Ordered) Space Required to Open oors 15 Four-foot Aisle for ontactor Removal 1. Recommended osition for Incoming otor onduit Recommended osition for Incoming ontrol onduit Indicates Terminal Location - Approximate for able Length Limitamp Limitamp AR AR ounting oles for 1/" iameter Anchor olts edium edium Voltage Voltage otor otor ontrol ontrol nclosures 1.1 nclosures nclosure nclosure Outline Outline dimensions dimensions Volts Volts R1 AR 00A, 1 igh, 0" Wide -100 lbs R1 AR 00A, 1 igh, 0" Wide 1 Kg (Stationary (Stationary or raw-out) or raw-out) L..SI TO AL TO AL TRY TRY TO AL TRY 10. T AL TRY otes: Incoming ower Terminal onnection Recommended osition for Incoming otor onduit Recommended osition for Incoming ontrol onduit 1-I Limitamp AR R1 AR 00A, 1 igh, 0" Wide... (Stationary or raw-out) TO AL TRY LA ontrol Lead Terminal oard otor Lead Terminal onnection round us Terminal onnection LA F round Terminal onnection (If.Ordered) Space Required to Open oors 15 Four-foot Aisle for ontactor Removal ounting oles for 1/" iameter Anchor olts TO Indicates Terminal Location - Approximate for able Length edium Voltage otor ontrol nclosures nclosure Outline dimensions Volts.5 R TO.. 1 igh, 0 Wide 1 1 L..SI L..SI lbs 0 Kg TO AL TO AL TRY TRY otes: Incoming ower Terminal onnection 1 A ower us ontrol Lead Terminal oard otor Lead Terminal onnection round us Terminal onnection F round Terminal onnection (If Ordered) Space Required to Open oors 15 Four-foot Aisle for ontactor Removal ounting oles for 1/" iameter Anchor olts Recommended osition for Incoming otor onduit lbs 0 Kg UR UIT TO UR UIT TO lbs 0 Kg..L..SI TO AL TRY otes: 1. Incoming ower Terminal onnection 1-I 1-I 1 A ower us ontrol Lead Terminal oard otor Lead Terminal onnection LA LA round us Terminal onnection F round Terminal onnection (If Ordered) Space Required to Open oors 15 Four-foot Aisle for ontactor Removal ounting oles for 1/" iameter Anchor olts Recommended osition for Incoming otor onduit Recommended osition for Incoming ontrol onduit Indicates Terminal Location - Approximate for able Length 1-I UR UI 0.0
6 Limitamp AR edium Votage otor ontrol R1 AR 00A, Stationary or raw-out, Outline imensions Volts, Two-igh, ottom able ntry Limitamp AR 10..Limitamp AR edium Voltage otor ontrol nclosures edium Voltage otor ontrol nclosures nclosure Outline dimensions Volts -00 lbs Kg R1 nclosure AR 00A, Outline igh, dimensions 0" Wide Volts L..SI (Stationary R1 AR or 00A, raw-out) igh, T 0" AL Wide TRY T AL TRY LOWR UIT (Stationary or raw-out) T AL TRY otes: UR UIT. tes: igh, Wide igh, 0 Wide TO L..SI L..SI lded 1. plate UR UIT 1.1 LOWR UIT LA lbs 111 Kg T AL TRY.0 1. otes: 1 A ower us ontrol Lead Terminal oard otor Lead Terminal onnection round us Terminal onnection Space Required to Open oors 15 Four-foot Aisle for ontactor Removal ounting oles for 1/" iameter Anchor olts Recommended osition for Incoming otor onduit Recommended osition for Incoming ontrol onduit Indicates Terminal Location - Approximate for able Length T AL TRY.0. - UR UIT -I 11. LOWR UIT 0.. LA LOWR UIT UR UIT TO Limitamp AR edium Voltage otor ontrol nclosures. nclosure Outline 0.0 for dimensions welded Volts. R1 AR 00A, igh, 0" Wide (Stationary or raw-out) T AL TRY UR UIT LOWR UIT LOWR UIT.5 LOWR UIT 1 UR UIT UR UIT UR UIT.0 TO UR UIT TO lbs for welded Kg 1. L..SI.0 LOWR UIT T AL UR UIT TRY - 1. LOWR UIT LOWR UIT UR UIT otes: 0. 1 A ower us LOWR UIT -I ontrol Lead 0. Terminal oard otor Lead Terminal onnection 0.0 -I round us Terminal onnection -50 lbs 111 Kg LA 0.0 Space Required to Open oors 15 Four-foot Aisle for ontactor Removal LA.0 1. ounting oles for 1/" iameter Anchor olts Recommended osition for Incoming otor onduit Recommended osition for Incoming ontrol onduit Indicates Terminal Location - Approximate for able Length Limitamp AR edium Voltage otor ontrol nclosures I 0.0 U LOW
7 nclosure Outline dimensions Volts R1 AR 00A, igh, " Wide (Stationary or raw-out)-to AL TRY Limitamp AR edium Votage otor ontrol R1 AR 00A, Stationary or raw-out, Outline imensions Volts, Two-igh, Top able ntry LOWR UIT LA igh, Wide Limitamp AR Limitamp AR edium Voltage otor ontrol edium Voltage nclosures otor ontrol 1.1 nclosures 1 1 nclosure Outline nclosure dimensions Outline dimensions Volts Volts -00 lbs -00 lbs R1 AR 00A, R1 igh, AR 00A, 0" Wide igh, 0" Wide Kg Kg (Stationary or (Stationary raw-out) L..SI or raw-out)-to AL L..SI TO TRY AL TRY AL TRY TO AL TRY otes: 1 A ower us, 100A A ower us, 000A ontrol Lead Terminal oard igh, otor 0 Lead WideTerminal onnection round us Terminal onnection Space Required to Open oors Anchor olts Recommended osition for Incoming otor onduit L..SI lbs 111 Kg 1 - UR UIT -I Recommended osition for Incoming ontrol onduit Indicates Terminal 10. Location - Approximate for able Length 1 Approximate 11 Weight Four-foot Aisle for ontactor Removal ounting oles for 1/" iameter -50 lbs 111 Kg L..SI TO AL TRY TO AL TRY otes: 1 A ower us, 100A otes: A ower us, 000A ontrol Lead Terminal oard 1 A ower us otor Lead Terminal onnection ontrol Lead Terminal oard round us Terminal onnection otor Lead Terminal onnection Space Required to Open oors 15 round us Terminal onnection Four-foot Aisle for ontactor Removal Space Required to Open oors 15 ounting oles for 1/" iameter Four-foot Aisle Anchor for ontactor olts Removal ounting oles Recommended for 1/" iameter osition for Incoming Anchor olts otor onduit Recommended osition for Incoming - LOWR UIT UR UIT LOWR UIT I Recommended osition for Incoming ontrol onduit Indicates Terminal Location - Approximate for able Length I UR UIT LOWR UIT UR UIT. bottom plate 1 0 LOWR UIT 0. -I LOWR UIT UR UIT 1 10 TO 5 Recommended osition for Incoming otor onduit Recommended osition for Incoming ontrol onduit Indicates Terminal Location - Approximate for able Length LA 1 LA LOWR UIT UR UIT TO
8 edium Voltage otor ontrol nclosures nclosure Outline Outline dimensions Volts Volts R1 R1 AR AR 00A, 00A, 11 igh, igh, " " Wide Wide (Stationary (Stationary or or raw-out) raw-out) T T AL AL TRY TRY Limitamp AR edium Voltage otor ontrol R1 AR 00A, Stationary or raw-out, Outline imensions Volts, One-igh, Top/ottom able ntry -/5 1-5/ 1-5/ 1-/ 1-/ -1/ -1/ -1/ -1/ -/ / 10 -/ 10-1/ 5-/ 1-/ 1-/ 1 -/ 10-1/ 10-5/ 1 -/ -1/ 1-1/ 5-1/ 1-1/ K -/ K -/ -1/ 11-1/ -/ -1/ -/ -1/ -1/ 1-1/ -/ / 1-/ 10-1/ -/ -1/ / 5 1-/ -1/ 10-5/, 1 F -1/ 10-5/-/ TO 1 F -/ TO 5-1/ -/ 1-1/ 1-1/ 1-1/ 5-1/ -/ 1-1/ 1-1/ 1-1/ 11-1/ -/ 0 for welded 11-1/ -1/ -/ 1-1/ 10-1/ 1 0 for L..SI welded -1/ 1-1/ 10-1/ / - 100LS. - K. 10-1/ -/, F K -/, F 1 F K K 1 F -/ -5/ K -/ 1-5/ -/ otes: -/ -5/ -/ 1-5/ Incoming ower Terminal / onnection -/ 10-1/ 1 A ower us, 00A / 10-1/ L..SI LA LS. ontrol Lead Terminal oard L..SI - K. otor Lead Terminal onnection LA LS. - K. 1 igh, Wide otes: otes: Incoming ower Terminal onnection 1 A Incoming ower us, ower 00A Terminal onnection ontrol Lead Terminal oard 1 A ower us, 00A otor Lead Terminal onnection ontrol Lead Terminal oard round us Terminal onnection otor Lead Terminal onnection F round Terminal onnection (If Ordered) round us Terminal onnection Space Required to Open oors 0 F Four-foot round Terminal Aisle for ontactor onnection Removal (If Ordered) ounting Space Required oles for to 1/" Open iameter oors 0 Anchor olts Recommended Four-foot Aisle osition for ontactor for Incoming Removal otor onduit Recommended ounting oles osition for 1/" for iameter Incoming Anchor ontrol olts onduit Recommended osition osition for for Incoming Incoming ower otor onduit onduit Indicates Recommended Terminal osition Location for - Incoming Approximate ontrol for able onduit Length Approximate Recommended Weight osition for Incoming ower onduit Indicates Terminal Location - Approximate for able Length -1/ round us Terminal onnection F round Terminal onnection (If Ordered) Space Required to Open oors 0 Four-foot Aisle for ontactor Removal ounting oles for 1/" iameter Anchor olts Recommended osition for Incoming otor onduit Recommended osition for Incoming ontrol onduit Recommended osition for Incoming ower onduit Indicates Terminal Location - Approximate for able Length Reference ublications Standard, non-arc Resistant Limitamp Vacuum ontactors Installation Instructions Application and Selection uide Load-reak Switches Installation Instructions Vacuum ontactors, Renewal arts ulletin T-0 - F-0 Industrial Solutions 1 Woodford Avenue lainville, T eneral lectric ompany Limitamp AR Limitamp AR roduct Flyer Limitamp AR Installation Instructions A-5-0 Information provided is subject to change without notice. lease verify all details with. All values are design or typical values when measured under laboratory conditions, and makes no warranty or guarantee, express or implied, that such performance will be obtained under end-use conditions. T-5 10/1
GE Industrial Solutions. Limitamp * AR. Arc Resistant Medium Voltage Motor Control. Installation Guide
GE Industrial Solutions Limitamp AR Arc Resistant Medium Voltage Motor ontrol Installation Guide Table of ontents Introduction...3 Opening Medium Voltage oor...3 Medium Voltage oor Latches... Isolation
More informationSection 18. Medium Voltage Equipment. BuyLog Catalog 18-1
MV One Line...18-2 Motor Control Medium Voltage (Limitamp ) Introduction, Features, Types, Options, References...18-3 Specifications, Ratings, Equipment Reference Publications...18-4 Product Scope...18-5
More information5kV to 38kV, 630 Amp to 4000 Amp Indoor or Outdoor Application
The most advanced Arc-Resistant Switchgear, designed and built to provide maximum safety in the event of an Internal Arcing Fault. 5kV to 38kV, 630 Amp to 4000 Amp Indoor or Outdoor Application Page 1
More informationSIMOVAC and SIMOVAC-AR. Medium-voltage controllers 2.3 kv kv. usa.siemens.com/simovac
0000 00000 0000 000 0000 000000 00000 0000 00000 0000 000 0000 000000 00000 SIMOVAC and SIMOVAC-AR Medium-voltage controllers 2.3 kv - 6.9 kv usa.siemens.com/simovac 2 SIMOVAC and SIMOVAC-AR - the latest
More informationSingle Socket and Horizontal Metering
G nergy onnections Single Socket and orizontal Metering T Approved Single Socket Metering T Approved Application Information G s Single Socket Metering products are designed for residential use. They are
More informationE C N A A F -
33-52 NA ontactors & Starters 3-Phase agnetic Starters nclosed Freedom Line January 1 Vol. 2, Ref. No. [0068] Selection Table 33-102. NA Freedom Line nclosed ontrol ing System 33 esign Page N - NA 33-40
More informationCR193 B,C,D and E Vacuum Limitamp * Contactors
GE Industrial Solutions CR19 B,C,D and E Vacuum Limitamp * Contactors Renewal Parts Bulletin Table of Contents General Information... Contactor Matrix... 4 Mounting Plates, Pull Handle, Interlock Driver
More information28.1. NEMA Contactors and Starters. Contents. Contactors Non-Reversing and Reversing. Freedom Series. Product Description
.1 NM ontactors and Starters Non- and ontactors ontactors Non- and Product escription Non- ontactors are most commonly used to switch motor loads in applications where running overcurrent protection is
More informationAmpgard The name motor applications rely on
Medium-voltage motor control Ampgard The name motor applications rely on Oil and gas Mining Water/wastewater Pulp and paper Utility Ampgard medium-voltage control solutions Eaton has been an industry leader
More informationIsys Micro Series. Valve Products. Operating information. Material specifications. Pilot configuration
atalog 000-3US The Valve System incorporates a space saving back to back valve mounting design, and achieves flow rates of 0.35 v per valve with valves having a combined width of mm. This plug-in valve
More informationMEDIUM VOLTAGE AIR INSULATED ARC-RESISTANT LOAD BREAK AND DISCONNECT SWITCHES
MEDIUM VOLTAGE AIR INSULATED ARC-RESISTANT LOAD BREAK AND DISCONNECT SWITCHES Description JRS arc-resistant fused/non-fused load break and fused/non-fused disconnect switches are available for applications
More informationPower Break II Switchboard
Power Break II Switchboard Now available with PowerBreak II Circuit Breakers through 4000A GE s Power Break II Switchboard is now available with the new Power Break II Insulated Case Circuit Breaker (800A
More informationMedium-Voltage Switchgear and Switches
edium-voltage Switchgear and Switches G edium-voltage Switchgear up to 6 kv, 2.500A Product overview Switchgear for primary distribution level type CPG.0, CPG.1, AC Switchgear for secondary distribution
More informationBasics of Medium Voltage Motor Control Starter Power Components & Starter Types
Basics of Medium Voltage Motor Control Starter Power Components & Starter Types Larry Dalton Lead Operation Specialist Jude Hernandez - Application Engineer GE Industrial Solutions Slide # 1, Rev 3, 11/8/16
More informationGE 8000-Line Motor Control Centers
GE 8000-Line -1 ENCLOSURE TYPES TYPE 1 General Purpose, Indoor Intended for use indoors, primarily to prevent accidental contact of personnel with the enclosed equipment, in areas where unusual service
More informationOpen, NEMA Type 1, 3R, 4/4X and 12. Auxiliary Contacts
0.- Motor Starters & ontactors Low Voltage Lighting ontactors lectrically eld N January 00 Sheet 18 0 1 7 8 0 1 7 8 0 N-Open (L0-nclosed) 0 mpere 0 mpere Product escription Lighting ontactors are designed
More informationLoad Centers and Circuit Breakers
Midwest lectric Products Load enters and ircuit reakers MLM4020U TQL2140 TQL11202 TQL1115 TQL2120T Midwest Load enters pplication Information Midwest load centers lower your costs by making installation
More informationMedium Voltage Equipment. Section 15.
MV One Line...15-2 Motor Control Medium Voltage (Limitamp ) Introduction, Features, Types, Options, References...15-3 Specifications, Ratings, Equipment Reference Publications...15-4 Product Scope...15-5
More informationCENTERLINE 1500 Medium Voltage Motor Control Centers
Selection Guide CENTERLINE 1500 edium Voltage otor Control Centers Designed for Intelligence, Safety, and Reliability CENTERLINE 1500 otor Control Centers edium Voltage otor Control Centers... 3 Standard
More informationIntroduction. Features. Intelligent Technologies Motor Control Center Structures
Intelligent Technologies Technical Data New Information Description Page Intelligent Technologies General............................................. 2 s.......................................................
More informationSIEMENS. Series 8100oT Vacuum Controllers. www. ElectricalPartManuals. com. Bulletin CC
c c SIEMENS Series 8100oT Vacuum Controllers Bulletin CC3802-02 Technological Development Vacuum technology has developed rapidly in recent years and is becoming widely accepted for medium voltage motor
More informationLow Voltage Switchgear Type WL Low Voltage Metal-Enclosed Switchgear
13 Low Voltage Switchgear Siemens Type WL low voltage metal-enclosed switchgear is designed, constructed and tested to provide superior power distribution, power monitoring and control. At the heart of
More informationType 2 Arc Resistant WL Low Voltage Metal-Enclosed Switchgear
Type 2 Arc Resistant WL Low Voltage Metal-Enclosed Switchgear IMPORTANT The information contained herein is general in nature and not intended for specific application purposes. It does not relieve the
More informationDesign Standard. Purpose: Design Standard:
Design Standard Purpose: This design standard has the purpose of creating a consistent application of motor-control centers throughout the East Side Union High School District, therefore achieving a standard
More informationGE Industrial Solutions. DEH Installation and Maintenance Manual AKD-20 AR / Entellisys AR Exhaust Plenum System
GE Industrial Solutions DEH-41474 Installation and Maintenance Manual AKD-20 AR / Entellisys AR Exhaust Plenum System Table of Contents General Information... ii Hazard Classifications... ii Trademarks...
More informationMichigan State University Construction Standards SECONDARY UNIT SUBSTATIONS PAGE
PAGE 261116-1 SECTION 261116 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationMEDIUM VOLTAGE CE-B36 METAL CLAD SWITCHBOARDS. CE - B36 - C - en - REV
CE - B36 - C - en - REV.00 2011.9 EDIU VOLTAGE EDIU VOLTAGE APPLICATION CE-B etal Clad switchboards are designed for use in public and industrial distribution system up to 36kV for the operation and protection
More informationEvolution * Series E9000 Motor Control Center
GE Industrial Solutions Evolution * Series E9000 Motor Control Center Renewal Parts Bulletin Table of Contents Introduction The E9000-Line motor control center, a quality product of the General Electric
More informationMEDIUM VOLTAGE CE-B METAL CLAD SWITCHBOARDS. CE - B - C - en - REV
MEDIUM VOLTAGE MEDIUM VOLTAGE APPLICATION CE-B Metal Clad switchboards are designed for use in public and industrial distribution system up to 24kV for the operation and protection of lines, generators,
More informationYLCS Water-cooled or remote air-cooled screw compressor chiller Heat pump application
YS ater-cooled or remote air-cooled screw compressor chiller eat pump application ooling capacities from 342 k to 10 k vailable configurations that meet lass energy efficiency levels at urovent Standard
More informationDESIGN GUIDELINES LOW VOLTAGE SWITCHGEAR PAGE 1 of 5
DESIGN GUIDELINES LOW VOLTAGE SWITCHGEAR PAGE 1 of 5 1.1. APPLICABLE PUBLICATIONS 1.1.1. Publications listed below (including amendments, addenda, revisions, supplements, and errata), form a part of this
More informationTECHNICAL AND APPLICATION GUIDE. SafeGear 5/15 kv, up to 50 ka arc-resistant switchgear
TECHNICAL AND APPLICATION GUIDE SafeGear 5/15 kv, up to 50 ka arc-resistant switchgear 2 SAFEGEAR 5/15 KV, UP TO 50 KA ARC-RESISTANT SWITCHGEAR SafeGear is ABB s ANSI arcresistant metal-clad switchgear
More informationGas Insulated Metal-clad Switchgear, HMGS!
Medium Voltage HMGS-G10 HYUNDAI Medium Voltage Gas Insulated Metal-clad Switchgear, HMGS! SF6 Gas Insulated Metal-clad Switchgear is an integrated assembly of vacuum circuit breaker, 3-position switch,
More informationMedium voltage switchgear SafeGear HD 63 ka arc resistant metal-clad switchgear. ABB Group February 25, 2015 Slide 1
Medium voltage switchgear SafeGear HD 63 ka arc resistant metal-clad switchgear ABB Group February 25, 2015 Slide 1 SafeGear HD arc resistant switchgear 63 ka arc resistant metal-clad air insulated switchgear
More informationCR193 Vacuum Limitamp* Contactors
GE Electrical Distribution GEH-5306C Maintenance Instructions CR193 Vacuum Limitamp* Contactors Contents Section 1 Introduction... 3 General... 3 Section 2 Description... 4 Principle of Operation... 4
More informationModel 6 Motor Control Centers Catalog 8998CT9701R07/ Class 8998
Catalog 8998CT9701R07/09 2009 Class 8998 CONTENTS Description............................................. Page Product Description.......................................... 7............................
More informationThree-PhaseVacuumCONTACTORS RP173. Features
Three-PhaseVacuumOTTORS RP173 easuring 18" x 18"W x 8" and weighing less than 67 lbs., the ennings RP173 Three-Phase Vacuum ontactor is built tough to work in a variety of heavy-duty applications. ble
More informationMESG 12 / 17.5 / 24 / 36 KV
MESG 12 / 17.5 / 24 / 36 KV Medium Voltage Air Insulated Metal Enclosed Switchgear up to 36 kv- up to 1250 A - up to 25 ka for 1 sec. with SF6 or vacuum circuit breakers. 750 METAL ENCLOSED 1 1 ) GENERAL
More informationMEDIUM VOLTAGE CE-B METAL CLAD SWITCHBOARDS. CE-B-C-en-REV
CE--C-en-REV.04 2016.1 MEDIUM VOLTAGE MEDIUM VOLTAGE APPLICATION CE- Metal Clad switchboards family are designed for use in public and industrial distribution system up to 40,5kV for the operation and
More informationTECHNICAL AND APPLICATION GUIDE. SafeGear 5/15 kv, up to 50 ka arc-resistant switchgear
TECHNICAL AND APPLICATION GUIDE SafeGear 5/15 kv, up to 50 ka arc-resistant switchgear 2 S A F E G E A R 5/ 1 5 K V, U P TO 5 0 K A A R C - R E S I S TA N T S W I TC H G E A R SafeGear is ABB s ANSI arcresistant
More informationSIGNAL WORDS QUALIFIED PERSON
SIGNAL WORDS The signal words Danger, Warning and Caution used in this manual indicate the degree of hazard that may be encountered by the user. These words are defined as: Danger - Indicates death or
More informationDesign Build Deliver. Metal Enclosed Switchgear, 5-35kV 1200 A Maximum Loadbreak, 4000 A Maximum Non-Loadbreak
Metal Enclosed Switchgear, 5-35kV 1200 A Maximum Loadbreak, 4000 A Maximum Non-Loadbreak Powergrid Solution s Metal Enclosed Switchgear has many different customizable options and configurations. Customers
More informationME Switchgear with Vacuum Circuit Breaker and Auto-jet II Switch with Ground Position
LET S BE PACIFIC November 0 Volume Number 5 ME Switchgear with Vacuum Circuit Breaker and Auto-jet II Switch with Ground Position Federal Pacific has the capability to engineer, fabricate and assemble
More information4-Way, 5-Port, 2 & 3-Position Solenoid and Remote Pilot 1/2" & 3/4" Ports. Technical & Service Data. Pneumatic
atalog VL-UTO-/US (Revised 6/0/0) pplication & Model Selection S utomotive Subbase Valves -Way, -ort, & -osition Solenoid and Remote ilot /" & /" orts pplication ual pressure or diverter valve operation
More informationMedium Voltage Metal-Enclosed Switches
Medium Voltage Metal-Enclosed Switches Outdoor Medium Voltage Switch.1 Medium Voltage Switch MVS Product Description............................................. 2 Application Description..........................................
More informationSingle Socket and Horizontal Metering
GE Energy onnections Single Socket and Horizontal etering EP pproved Single Socket etering EP pproved pplication Information GE s Single Socket etering products are designed for residential use. They are
More informationSUBSTATION VACUUM CIRCUIT BREAKER (15.5KV)
SUBSTATION VACUUM CIRCUIT BREAKER (15.5KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products for utilities
More informationSUBSTATION VACUUM CIRCUIT BREAKER (25.8 / 27KV)
SUBSTATION VACUUM CIRCUIT BREAKER (25.8 / 27KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products
More informationSUBSTATION VACUUM CIRCUIT BREAKER (38KV)
SUBSTATION VACUUM CIRCUIT BREAKER (38KV) For more than four decades, Myers Power Products has led the switchgear market in quality for the electric industry, delivering highly reliable products for utilities
More informationMotorpact Medium Voltage Motor Controller. Innovative solutions that deliver high performance and reliability
Motorpact Medium Voltage Motor Controller Innovative solutions that deliver high performance and reliability A tradition of trusted innovation For one hundred years, the Square D brand has provided leading
More informationThe safest, most reliable Switchgear in the market today
February 2008 MV Metal-Clad Switchgear The safest, most reliable Switchgear in the market today January 4, 2015 Slide 1 Arc-Resistant Standards Introduction Today s Topics What is Arc Flash and the risks
More information.1 NM ontactors and Starters Product Overview starters and contactors feature a compact, space-saving design, using state-of-the-art technology and th
NM ontactors and Starters NM N16N0 NM Size 1 Starter.1 Product Overview.............................................. Features, enefits and Functions.................................. Standards and ertifications......................................
More informationNEMA Contactors and Starters
NM ontactors and Starters NM N16N0 NM Size 1 Starter NM Size 1 ontactor.1 Product Overview.............................................. 242 Features, enefits and Functions..................................
More information2018 Consultant s Handbook Division 26 Electrical 2413 Switchboards
1 General 1.1 Switchboards shall be U.L. listed and labeled. 1.2 Each switchboard shall have its own main disconnecting means unless it is located in the same room as its source of origin. In most cases
More informationPRESSURE REDUCING MODULAR VALVE. 40 to 300l/min 25,35MPa
RSSUR RU UR VV Reducing to l/min,a eatures qhis modular valve makes the pressure in part of the circuit lower than the main circuit. wven when pressure changes in the primary main circuit, the reduced
More informationMedium Voltage Distribution PIX. Air Insulated Switchgear up to 24 kv PARS TABLEAU
Medium Voltage Distribution PIX Air Insulated Switchgear up to kv PIX Air Insulated Switchgear up to kv The PIX system has been designed in accordance with international (IEC) standards, and gives an optimal
More informationValve Products. B Series Valve
atalog 000- arker neumatic Valve, an exceptional performing industrial valve in a compact size with an enhanced flow range. vailable in solenoid pilot operated and remote air pilot models. he series features
More informationFH Fan-Coil Units Low-Profile, Horizontal
FH Fan-oil Units Low-Profile, Horizontal FH Fan-oil Units: Innovative design simplifies installation and service Owners HRI Standard 440-certifi cation ensures exacting performance. The FH fan-coil unit
More informationC1000 Series Automatic Cap Bank
C1000 Series Automatic Cap Bank Metal Enclosed - Medium Voltage Capacitors Assemblies Fixed / Auto Medium Voltage 5, 15, 25 and 35 kv Class Customized to your specifications The Reactive Power Solution
More information24kV Medium Voltage Switchgear Metal-Enclosed (LSC2A)
M6 24kV Medium Voltage Switchgear MetalEnclosed (LSC2A) GENERAL FEATURES GENERAL DESCRIPTION The structure of the cubicles, of considerable strength, has selfsupporting structure and is made of steel sheet
More informationPower/Vac OEM Express Switchgear
g Power/Vac OEM Express Switchgear Metalclad Switchgear 4.16kV-250 MVA through 13.8kV-1500 MVA DEA-275 FULLY ASSEMBLED MECHANICALLY COMPLETE SWITCHGEAR WITHOUT DEVICES AND WIRE. POWER/VAC OEM EXPRESS SWITCHGEAR
More informationMV Metalclad Switchgear 4760V-15000V 20KA-63KA. AC Power Circuit Breaker Rating Structure. Test Procedures for Power Circuit Breakers
Contents Key Features and Benefits Codes and Standards Value Addition by Application of PVAC-E GE Components Inside Design Features on PVAC-E Switchgear PVAC-E Switchgear Configuration PVAC-E Switchgear
More informationDescriptive bulletin. Medium voltage load interrupter switchgear Reliable, low maintenance and economical for distribution applications
Descriptive bulletin Medium voltage load interrupter switchgear Reliable, low maintenance and economical for distribution applications General overview Reliable, low maintenance and economical Load Interrupter
More informationVacClad-W type VCP-W 5 and 15 kv, 36-inch-wide switchgear components
Supersedes July 2002 Contents Page Procedure for identifying parts... 2 Customer ordering instructions.... 2 Distributor ordering instructions.... 2 Front panel components.... 3 Breaker pan assembly....
More informationSafeGear TM Motor Control Center Arc resistant metal-clad construction
SafeGear TM Motor Control Center Arc resistant metal-clad construction Contents Description 2 SafeGear TM MCC applications 3 Electrical features 3 Standards 3 Standard service conditions 4 HCV vacuum contactor
More informationDynamic Braking Kit for FlexPak 3000 and WebPak 3000 Digital DC Drives 1.5 HP to VAC, 3 HP to VAC without NEMA1 Enclosures
Dynamic Braking Kit for FlexPak 3000 and WebPak 3000 Digital DC Drives 1.5 HP to 150 HP @ 230 VAC, 3 HP to 600 HP @ 460 VAC without NEA1 Enclosures odel Numbers 912FKxxxx and 913FKxxxx Instruction anual
More informationValve Products. Viking Lite Series Valves. Operating information. Minimum operating pressure, PSIG (bar) Materials. Recommended air quality for valves
atalog 000-US arker neumatic Valve roducts Viking ite Valves The Viking ite valve range is robust, versatile and combines a large flow capacity with short change-over times, designer may choose /8, / or
More informationSafe and Reliable. Flexible, Compact Design. Easy Installation and Maintenance
M E T A L - C L A D S W I T C H G E A R Safe and Reliable Flexible, Compact Design Easy Installation and Maintenance We build a better future! Hyundai HMS medium-voltage metal-clad switchgears and control-gears,
More informationWorm Gear Hand Winches Up to 4000 lb capacity
IO 900 ertified Worm Gear and Winches Up to 4000 lb capacity achine ut Worm Gears provide accurate operation and long lasting service. nclosed Oil ath provides continuous lubrication of gears to minimize
More informationNEMA Contactors & Starters A200
March 007 NM ontactors & Starters 00 ontactors Non-reversing and Reversing -7 ontents escription Page ontactors Non-reversing and Reversing............ -7 Product escription Sizes 00 4............ -7 Product
More informationVOLUME: IIIC SCHEDULE IIIC/4 11 KV AND 3.3 KV SWITCHGEARS
VOLUME: IIIC SCHEDULE IIIC/4 11 KV AND 3.3 KV SWITCHGEARS A. 11 KV SWITCHGEAR 1.0 SWITCHGEAR ASSEMBLY 1.1 Make : 1.2 Type : 1.3 Reference Standard : 1.4 Voltage (Nom./Max.) KV : 1.5 Phase, Frequency No,Hz.
More informationSpecification Pad-Mounted Capacitor Bank with Dual Fusing Integral Load-Interrupter on Line-Side Fuse Mountings
Page 1 Specification Pad-Mounted Capacitor Bank with Dual Fusing Integral Load-Interrupter on Line-Side Fuse Mountings I. General This specification covers the design requirements for a pad-mounted capacitor
More informationENERPAC hydraulic valves are available in a wide variety of models and configurations.
irectional ontrol s EE hydraulic valves are available in a wide variety of models and configurations. Whatever your requirements directional control, flow control, or pressure control you can be sure that
More informationFOR PRICES ON DSII and DSLII BREAKERS, REFER TO PRICE LIST PL.22B.01.P.E
Supersedes PL.44B.04.P.E Dated September 1998 600 Volts AC Maximum 200 ka, RMS Sym. Short Circuit Maximum 800-5000 Amps Continuous Effective: October 1999 Page 1 Index Page Table Description/Application...
More informationMetal-Enclosed Switches. Medium Voltage. Medium Voltage Metal-Enclosed Switches Contents
January 2003 Vol. 1, Ref. No. [1011] -1 Medium Voltage Metal-Enclosed Switches Contents Description Page MVS................................... -2 and Breaker MSB........................ -3 Metal-Enclosed
More informationwww. ElectricalPartManuals. com Section 13 Switchgear Low Voltage
Switchgear Low Voltage Introduction...13-1 AKD-10 Low-Voltage Switchgear...13-3 AKD-20 Low-Voltage Switchgear...13-3 Low Voltage Switchgear GE low-voltage switchgear is heavy-duty equipment built to ANSI
More informationViking Lite Series Valves Air Control Valves
atalog 0697 arker neumatic Viking ite Series Valves ir ontrol Valves The Viking ite valve range is robust, versatile and combines a large flow capacity with short change-over times, designer may choose
More informationMedium Voltage Metal-Enclosed Switches
Medium Voltage Metal-Enclosed Switches Outdoor Medium Voltage Switch.1 Introduction Product Selection Guide....................................2 Medium Voltage Switch MVS Product Description......................................
More informationIsolation Switch (behind barrier & inspection window) Power Fuses. Load Cable Connection Box. Contactor. Control Power Transformer Secondary Fuse
Instruction Bulletin Class 8198 ISO-FLEX Medium Voltage Controller Model 3, Series B Installation and Maintenance Bulletin No. 50006-376-01 August, 1995 Raleigh, NC, USA TABLE OF CONTENTS Introduction...
More informationADEX Series. Air Control Valves. Section D
X Series ir ontrol alves 00.0 v.8 v.47 v ort 5 ort /8" ort Section www.parker.com/pneu/adex X iking Z asic alve unctions...00 asic alve eatures...0 ommon art umbers / R Type alves...02 odel umber Index
More informationChapter 6 Generator-Voltage System
Chapter 6 Generator-Voltage System 6-1. General The generator-voltage system described in this chapter includes the leads and associated equipment between the generator terminals and the low-voltage terminals
More informationNMC Combination Line Starters and Enclosures
NMC Combination Line Starters 600VAC Heavy uty atertight eatherproof Applications: NMC combination magnetic line starters are for use in across-the-line motor starting, motor disconnect, motor and line
More informationR-Rated medium voltage fuses for motor circuit protection
Technical ata 6001 Supersedes September 2017 Features and benefits escription: Indoor/enclosure, R-Rated medium voltage, current-limiting fuses for motor circuit protection. urrent-limiting R-Rated fuses
More informationSafeGear Motor Control Center Arc Resistant Metal-Clad Construction Brochure
2017 SafeGear Motor Control Center Arc Resistant Metal-Clad Construction Brochure SafeGear Motor Control Center Arc resistant Metal-Clad construction Brochure Table of Contents 1. Description 1 1 2. SafeGear
More informationFor Options, Modifications and Accessories, see pages Discount Schedule A6
Main and Feeder Units Bulletin 191F and 191M Outgoing Feeder Lug Compartment (FLUG) and Incoming Main Lug Compartment (MLUG)................................................. The Bulletin 191M and 191F
More informationT H QL Recommendations based on standard conditions. Installation must conform to all local and national codes.
atalog Number ystem For illustrative purposes only. ircuit reaker election uide T QL 5 E Identification Interrupting Rating Type oles Voltage mpere Rating Insert for pecials = 0kI QL = lug-in = 20/240Vac
More informationADEX Series Air Control Valves A00.01 Cv M3 Port A05.18 Cv M5 Port A12.47 Cv 1/8" Port zpv02 A B C D E F G H. Section H
X Series ir ontrol alves 00.0 v ort 05.8 v 5 ort.47 v /8" ort zpv02 Section www.parker.com/pneu/adex asic alve unctions... 2 asic alve eatures... ommon art umbers / R Type alves... 4 odel umber Index /
More informationA system fault contribution of 750 mva shall be used when determining the required interrupting rating for unit substation equipment.
General Unit substations shall be 500 kva minimum, 1500 kva maximum unless approved otherwise by the University. For the required configuration of University substations see Standard Electrical Detail
More informationR-Rated medium voltage fuses for motor circuit protection
Technical ata 6001 Supersedes ecember 2015 Features and benefits escription: Indoor/enclosure, R-Rated medium voltage, current-limiting fuses for motor circuit protection. urrent-limiting R-Rated fuses
More informationInstructions for AMPGARD 400A medium voltage starter
Read and understand this manual in its entirety before installing or operating the controller. Installation, adjustment, repair, and maintenance of these controllers must be performed by qualified personnel.
More informationPREFACE ********************************************************** IT IS NOT INTENDED THAT THESE STANDARDS BE COPIED AND USED AS A SPECIFICATION!
PREFACE This publication has been prepared as a guide for Architectural and Engineering (A&E) firms in the preparation of documents for the design and construction of new structures and the remodeling
More informationwith Vacuum Circuit Breaker HAF
M E T A L - C L A D S W I T C H G E A R Safety and Reliability with Vacuum Circuit Breaker HAF Flexible Design and Compact with Vacuum Circuit Breaker HVF Easy Installation and Maintenance We build a better
More informationReliably Switching Highest Currents up to 2000 A
www.moeller.net Reliably Switching Highest Currents up to 2000 A The complete range for the motor circuit. From contactors to efficient motor-starters to controlled drives. New solutions that rely on communication.
More informationEMPAC Metal enclosed capacitor bank for wind applications
EMPAC Metal enclosed capacitor bank for wind applications Introduction The EMPAC is a Metal Enclosed Capacitor Bank suitable for voltages between 1 kv and 36 kv for reactive compensation in MV networks
More informationMedium Voltage Equipment 5-15 kv GM-SG and 38 kv GM38 Metal-Clad Switchgear General
13 SWITCHGEAR Medium Voltage Equipment -1 kv GM-SG and 38 kv GM38 Metal-Clad Switchgear General Overview Features Siemens, 7, 1 and 38kV class medium voltage, one- or two-high vacuum circuit breaker switchgear
More informationOur brand POWER DYNAMIC PASSION COMMITMENT CREATIVITY. A strong brand for strong products: 8PU Premium. MV Energy
Our brand A strong brand for strong products: The ENERGOLINE brand represents our product portfolio of INDUSTRIAL SWITCHGEAR SYSTEMS. Our products are characterized by a high degree of safety, flexibility
More informationPOWER-ZONE 4 Low Voltage Metal-Enclosed Drawout Switchgear with MASTERPACT NW Low Voltage Power Circuit Breakers
POWER-ZONE 4 Low Voltage Metal-Enclosed Drawout Switchgear with MASTERPACT NW Low Voltage Power Circuit Breakers Class 6037 CONTENTS Schneider Electric Brands Description Page Product Description..................................................
More informationMEDIUM VOLTAGE PRODUCT CAPABILITIES OVERVIEW
MEDIUM VOLTAGE PRODUCT CAPABILITIES OVERVIEW Medium Voltage Product Overview MVB SERIES, MEDIUM VOLTAGE DRAW-OUT CIRCUIT BREAKER MVB SERIES Standard Breaker Features : 1200, 2000, 3000 Amps, 3 phase, 60
More informationCENTERLINE 2500 Low Voltage Motor Control Centers and Power Distribution Gear Catalog Structure Breakdown
Technical ata CENTERLINE 2500 Low Voltage Motor Control Centers and Power istribution Gear Catalog Structure Breakdown Catalog Numbers 2500 Table of Contents Topic Page Additional Resources 2 Ordering
More informationGE 8000-Line Motor Control Centers Mains, Feeders, Incoming Lines C-1
GE 8000-Line -1 Mains, coming Lines MAINS GENERAL Main units consist of an externally operable circuit disconnect, either a fusible switch or a circuit breaker. Sizes by ampere rating, short-circuit rating,
More information