Screwpump Series ACD
|
|
- Jason Harrell
- 6 years ago
- Views:
Transcription
1 Screwpump Series ACD Product description Flow volume: l/min Max differential pressure: 7 bar Applications: Lubrication, circulation and transfer ACD 1116 GB IMO AB, Telephone: , Telefax:
2 The ACD pumps are used for a number of different fluids: Lubrication oil, fuel oil, vegetable oil, hydraulic oil and other hydraulic fluids, glycols, polymers, emulsions, and any nonaggressive fluid with some lubricating properties. Typical application are: Lubrication of diesel engines, gears, gas Applications Technical data and steam turbines, hydro turbines, paper machines. Circulation for cooling and filtration in large machineries and hydraulic systems, pumping transformer oil for insulation in transformers. Transfer onboard ships, in oil factories, refineries, tank farms etc. Discharge pressure Maximum discharge pressure is 12 bar Differential pressure Maximum differential pressure is 7 bar but is reduced at low viscosities as shown in the table below. Viscosity, mm2/s (cst) Max. diff. pressure (bar) 4,2 4,7 5,1 5,5 5,8 6,0 6,3 6,5 6,7 Inlet pressure Max. inlet pressure is 7 bar Min. inlet pressure is shown in the Selection guide Displacement cm3/r Size,lead 025L 025N Displacement cm 3 /r Pressure relief valve The pump is equipped with an integral pressure relief valve with internal return, limiting the differential pressure across the pump and protecting the pump should the discharge line be blocked. The valve is adjustable for different opening pressures. The value of the pressure limit can be set at the factory and should be adjusted at installation (see Installation & Startup instruction for Low pressure pumps). The valve has a pressure accumulation of max. 4 bar, so with moderate demands on pressure modulation, it may also be used for pressure regulation. The valve has a max. set pressure of 7 bar. Drive The pump is designed to be short coupled to an electrical motor IEC size 71. The motor bearing will have to carry a slight axial load from the rotor set. With motors delivered from IMO AB, this load will not significantly impair the bearing life expectancy. Max speed limit The maximum speed is 3600 rpm. For higher speeds contact IMO AB. Rotation The ACD pump is designed to operate in one rotational direction only, as standard clockwise when facing the shaft end. Fluid viscosity mm 2 /s. For higher viscosities contact IMO AB. Pumping temperature -20 C to 90 C for all types of ACD. Sound level A typical sound level from a pump with standard driver is 58 db(a). This value refers to free field conditions at 5 bar, 2940 rpm and 40 cst, measured according to ISO Standard and recommendation Version NTBP is recommended whenever the starting viscosity might exceed 800 cst. Unless otherwise specified, version IVBP will be delivered. 2 IMO AB, Telephone: , Telefax: ACD 1116 GB
3 Material and design IVBP NTBP Pump body Pearlitic cast iron Nodular cast iron Power rotor Steel, surface treated Steel, surface treated Idler rotors Pearlitic cast iron, Pearlitic cast iron, surface treated surface treated Shaft seal Carbon/Ni-resist Carbide/Carbide Viton elastomers Viton elastomers Viscosity table cst SSU 32,6 39,2 52,2 99, Units The following units are frequently used for specification of pumps: SI-unit IMO units USA units conversion Pressure Pa (MPa) bar psi 1 bar = 14,5 psi = 0,1 MPa Speed r/s rpm rpm 1 rpm = 0, r/s Viscosity mm2/s cst SSU see table Temperature C C F C = ( F-32)/1,8 Length m mm inch 1 mm = 0,0394 inch Flow rate m3/s lit/min GPM 1 lit/min = 0,264 GPM Pump model code Pump series ACD Size (Power rotor diameter, mm) Lead L=Low lead N=Normal lead Generation Design generation 6 Material in pump body I=Perlitic cast iron N=Nodular cast iron Shaft seal design V=Carbon/Ni-resist. elastomers in Viton T=Carbide/Carbide, elastomers in Viton Mounting B=Flange mounting Valve P=Pressure relief valve included Special design Code group omitted for standard design ACD 1116 GB IMO AB, Telephone: , Telefax:
4 Selection guide 50 Hz Size Visc. (lit/min) Speed: 1450 rpm Speed: 2900 rpm & Diff. pressure (bar) Min.inlet Diff. pressure (bar) Lead (cst) (kw) (bar)* Min.inlet (bar)* 20 Qeff Pe Qeff L Pe Qeff Pe Qeff Pe Qeff Pe Qeff N Pe Qeff Pe Qeff Pe * Valid for liquids free from unresolved air or gas. Selection guide 60 Hz Size Visc. (lit/min) Speed: 1750 rpm Speed: 3500 rpm & Diff. pressure (bar) Min.inlet Diff. pressure (bar) Lead (cst) (kw) (bar)* Min.inlet (bar)* 20 Qeff Pe Qeff L Pe Qeff Pe Qeff Pe Qeff Pe Qeff N Pe Qeff Pe Qeff Pe * Valid for liquids free from unresolved air or gas. 4 IMO AB, Telephone: , Telefax: ACD 1116 GB
5 Pump dimensions Pump ACD Dimensions in mm (The counter flanges are accessories) Fig. 1 Pump unit ACD Dimensions in mm (With standard electric motor) Fig. 2 ACD 1116 GB IMO AB, Telephone: , Telefax:
6 Accessories A bare shaft pump (fig. 3) can be ordered with the accessories in fig Fig. 4 Set of counter flanges Fig. 5 Angle bracket Fig. 3 Bare shaft pump Fig. 6 Double assembly unit The ACD-pump with counter flanges of the weld neck type is mounted directly to an electric motor and has an angle bracket for mounting horizontally, vertically or any other attitude. Two pump units can also be mounted to a double assembly on a common frame with inlet and outlet pipe Installation Fig. 7 Electric motor connections. The double assembly saves space and facilitates installation, maintenance, service and supervision. See Product Description for T4. For more information about installation read the Installation and Start-up manual for low pressure pumps. Spare parts for these pumps are easily available from stock. For detailed information and know-how about service read the Maintenance and Service Maintenance and Service instruction for ACD-pumps or contact IMO AB. 6 IMO AB, Telephone: , Telefax: ACD 1116 GB
7 ACD 025, all models Sectional view flow out flow in A Fig. 8 Pos No List of components Denomination Pos No Denomination 1020 Power rotor 134 Locking screw 162 Nylon sleeve socket 202 Idler rotor 401 Pump body 443 Drip nipple 451 Screw 501 Front cover 506 O-ring 509 Shaft seal 551 Rear cover 556 Gasket 601 Valve cover 602 Sealing washer 605 O-ring 612 Regulating screw 612A Retaining ring 614 Valve piston 615 Valve spring ACD 1116 GB IMO AB, Telephone: , Telefax:
8 IMO AB: P.O. Box 42090, S STOCKHOLM, Sweden. Telephone: Telex: IMO S, Telefax: , 8 IMO AB, Telephone: , Telefax: ACD 1116 GB
Flow volume: 2-24 l/min Max differential pressure: 10 bar Applications: Lubrication, circulation and transfer
Screw pump Series LPD Product description Flow volume: 2-24 l/min Max differential pressure: 10 bar Applications: Lubrication, circulation and transfer The LPD pump is used for a number of different fluids:
More informationACD6. Std Line. Product Description. Max differential pressure: 7 bar Circulation, lubrication and transfer ACD GB
ACD6 Std Line Product Description Flow volume: 10-42 l/min Max differential pressure: 7 bar Applications: Circulation, lubrication and transfer 1. Applications 1.1 Functionality The ACD pumps come in two
More informationFlow volume: l/min Max differential pressure: 16 bar Applications: Lubrication, circulation and transfer
Std Line ACE3 Screwpump Series Product description Flow volume: 15-180 l/min Max differential pressure: 16 bar Applications: Lubrication, circulation and transfer The Std Line (standard) ACE pumps come
More informationFlow volume: l/min Max differential pressure: 16 bar Applications: Lubrication, circulation and transfer
Opti Line ACG8 Screw pump Product description Flow volume: 80 1200 l/min Max differential pressure: 16 bar Applications: Lubrication, circulation and transfer The ACG pumps are used for a number of different
More informationACG7. Std Line. Product Description. Max differential pressure: 16 bar Circulation, lubrication and transfer ACG GB
ACG7 Std Line Product Description Flow volume: 80-1200 l/min Max differential pressure: 16 bar Applications: Circulation, lubrication and transfer 1. Applications 1.1 Functionality The Std Line (standard)
More informationLPE3. Std Line. Product Description. Max differential pressure: 16 bar Circulation, lubrication and transfer LPE GB
LPE3 Std Line Product Description Flow volume: 10-180 l/min Max differential pressure: 16 bar Applications: Circulation, lubrication and transfer 1. Applications 1.1 Functionality The Std Line (standard)
More informationLPE4. OptiLine. Product Description. Max differential pressure: 16 bar LPE GB
LPE4 OptiLine Product Description Flow volume: 8-175 l/min Max differential pressure: 16 bar Applications: Circulation and transfer 1. Applications 1.1 Functionality The LPE OptiLine pump is used for a
More informationACF5. Std Line. Product Description. Max differential pressure: 16 bar Circulation, lubrication and transfer ACF GB
ACF5 Std Line Product Description Flow volume: 310-2900 l/min Max differential pressure: 16 bar Applications: Circulation, lubrication and transfer 1. Applications 1.1 Functionality The ACF pumps are used
More informationACF5. Std Line. Product Description. Max differential pressure: 16 bar Circulation, lubrication and transfer
ACF5 Std Line Product Description Flow volume: 310-2900 l/min Max differential pressure: 16 bar Applications: Circulation, lubrication and transfer ALSO VALID FOR PUMP SERIES UCF Generation 5 1. Applications
More informationScrewpump. Series D GB. General Description. Model Code D 4
Screwpump Series D4 A Member of the COLFAX PUMP GROUP Handling of hydraulic oils, seal oils and fuel oils Max. working pressure: 160 bar Flow range: 10-850 I/min General Description Positive constant displacement,
More information8L SERIES THREE SCREW PUMPS
TM 8L SERIES THREE SCREW PUMPS The reliable pump people ROTARY SCREW PUMPS Performance Shown at 1500 PSID (103 BAR), 200 SSU (43 CST) 60 HZ: 870 1150 1750 50 HZ: 960 1450 1200 1100 630M 40 250 1000 900
More informationMaintenance and Service Instruction
Screw pumps ACD Maintenance and Service Instruction This instruction is valid for all ACD pump models shown on page 2 Contents Page List of components 2 Exploded view/ordering code 3 Service intervals
More informationHydraulic gear pumps and motors
PL 01 T E DISPLACEMENTS From To Hydraulic gear pumps and motors 0.07 in 3 /rev (1.07 cm 3 /rev) 5.56 in 3 /rev (91.10 cm 3 /rev) through bore aluminum body PRESSURE Max. Continuous Max. Intermittent Max.
More informationPump your business. 40 bar program. Screw pumps series SMxT16B Dry & submersible screw pumps for industrial applications
Pump your business 40 bar program Screw pumps series SMxT16B Dry & submersible screw pumps for industrial applications The people behind the Settima pumps The Settima Meccanica adventure started in early
More informationSeries PRODUCTS. self-priming Horizontal screw pump for non lubricating liquids. Water. Seawater. Heavy fuel oils. Bilge/Ballast pumps
self-priming Horizontal screw pump for non lubricating liquids PRODUCTS Water Seawater Oils Heavy fuel oils Light products Labelling Bilge/Ballast pumps General service pumps Cargo pumps Transfer pumps
More informationVIKING HG SERIES HELICAL GEAR EXTERNAL GEAR PUMPS
Page 350.1 Series Description Viking s HG series positive displacement pumps are designed to provide low noise transfer and processing of clean, lubricating liquids for applications such as lube oils,
More informationEMTEC Series 3-Screw
EMTEC Series 3-Screw Coolant and Emulsion Pumps The reliable pump people Rotary Screw Pumps Performance Shown at 1.8 cst, 3500 RPM Differential Pressure PSI 20-38 20-46 20-56 40-38 40-46 80-36 80-46 140-39
More informationISD SO-NB-G105 SO-NB-G85 SO-NB-P46 PV2R1-* - * -RAA-42/4290 PV2R2-* - * -RAA-41/4190 PV2R3-* - * -RAA-31/3190 PV2R4-* - * -RAA-30/3090
Spare Parts List PVR-* - * -RAA-4/4 PVR-* - * -RAA-4/4 PVR-* - * -RAA-/ PVR4-* - * -RAA-/ 4 5 4 6 8 8 6 5 4 Y Section Y-Y Y 6 5 Section - 8 Cartridge Kits Model Numbers PVR-6- * -RAA-4 * PVR-8- * -RAA-4
More informationTHRU DRIVE HYDRAULIC VANE PUMP TQ/TV SERIES
THRU DRIVE HYDRAULIC VANE PUMP TQ/TV SERIES TQ/TV THRU-DRIVE HYDRAULIC VANE PUMPS TQ/TV SERIES Thru-drive pumps save installation space and cost by eliminating double shaft extension electric motors or
More informationLift & elevators program Screw pumps series SMU / SMU AC / SMTU
Catalogo SMU USA. 5-02-2008 9:51 Pagina 1 Lift & elevators program Screw pumps series SMU / SMU AC / SMTU Submersible & Dry screw pumps Catalogo SMU USA. 5-02-2008 9:51 Pagina 2 The people behind the Settima
More informationAP212 Gear Pumps. Standard and Low Noise series. Reference: 200-P EN-03 1/60. Issue:
Gear Pumps Standard and Low Noise series Reference: 2-P-99123-EN-3 Issue: 9.215 1/6 Contents Page 1 General information... 4 1.1 External gear pumps components... 5 1.2 Example of typical sound pressure
More informationGRUNDFOS DATA BOOKLET MTS. Screw pumps 50/60 Hz
GRUNDFOS DATA BOOKLET MTS Screw pumps / Hz Contents Introduction MTS 3 Performance range - MTS, Hz 4 Performance range - MTS, Hz 5 Performance range - MTS, Hz 5 General description Main applications 6
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BV
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BV BV FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES
BV FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BV SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationLEISTRITZ PUMPEN GMBH. Leistritz Screw Pumps & Systems L3MA 3 L. The new L3MA pump series according API 676 3rd. API 676 3rd. 6 3r
LEISTRITZ PUMPEN GMBH Pumpen MA Re L3 rd 63 The ne w d 6 3r 67 L3MA pump ser ie MA 3 L rding API cco 67 sa L3MA_8s_en.indd 1 entspricht AP I ihe Die ne ue Leistritz Screw Pumps & Systems The new L3MA pump
More informationMS-Series. S Series. Twin Triple Screw Pumps.
MS-Series S Series Twin Triple Screw Pumps W h e r e I n n o v a t i o n F l o w s www.maag.com Triple Screw Pump S E R I E S A Safer, Greener, More Cost-Effective Pumping Solution Maag, part of Dover
More information5.2 MEDIUM HEAVY DUTY SERIES SIZE 3
.2 MEDIUM HEAVY DUTY SERIES SIZE 3 CONTENTS PGI101 Ordering Code.2.1 Medium Heavy Duty Series Technical Information.2.2 Specifications.2.3 Hydraulic fluids.2.4 Viscosity range.2. Temperature range.2.6
More informationQuality Products for Mechanical & Fluid Power. TQ & TV Series VANE PUMPS
1 Quality Products for Mechanical & Fluid Power 1 TQ & TV Series VANE PUMPS TQ/TV THRU-DRIVE HYDRAULIC VANE PUMPS TQ/TV SERIES Thru-drive pumps save installation space and cost by eliminating double shaft
More informationL & C SERIES. Lubrication & Circulation Pumps. Pump Your Heart Into It
L & C SERIES Lubrication & Circulation Pumps Pump Your Heart Into It LEGENDARY SUCCESS The L & C Series cast iron positive displacement pumps have been the industry standard for Lubrication & Circulation
More informationProduct Range IDEX CORPORATION
Product Range IDEX CORPORATION Viking Pump provides an unmatched combination of application expertise and positive displacement pumping products to meet your pumping needs. We specialize in the design,
More information4.2 FIXED DISPLACEMENT DOUBLE PUMP
4.2 FIXED DISPLACEMENT DOUBLE PUMP CONTENTS PVF101 Ordering Code 4.2.1 Fixed Displacement Technical Information 4.2.2 Specifications 4.2.3 Hydraulic fluids 4.2.4 Viscosity range 4.2.5 Temperature range
More informationThis instruction is valid for all ACF/UCF pump models shown on page 2
Screw pumps A Member of the COLFAX PUMP GROUP ACF/UCF Maintenance and Service Instruction This instruction is valid for all ACF/UCF pump models shown on page 2 Contents Page List of components 2 Exploded
More informationMOTOR SPEED PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1442 Page 1442.
Page 1442.1 TABLE OF CONTENTS Features & Benefits...2 Standard Materials of Construction...2 Specifications...2 Model Number Key...3 Cutaway View & Pump Features...3 Dimensions C, F, FH Sizes...4 Dimensions
More informationUNIVERSAL PRODUCT LINE: STAINLESS STEEL JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
UNIVERSAL PRODUCT LINE: SERIES 227A, 4227A, 327A, 4327A Section 1702 Page 1702.1 Issue B TABLE OF CONTENTS Features & Benefits...2 Jacketing...2 Relief Valve Configurations...3 Porting & Sealing...3 Revolvable
More informationVickers. Piston Motors. Inline Piston Motors. Fixed and Variable Displacement. Revised 5/99 691
Vickers Piston Motors Inline Piston Motors Fixed and Variable Displacement Revised 5/99 691 Table of Contents Introduction........................................................................................
More informationTRITEC SERIES THREE SCREW PUMPS
TM TRITEC SERIES THREE SCREW PUMPS The reliable pump people ROTARY SCREW PUMPS Performance Shown at 3500 RPM, 1.0 Centistokes DIFFERENTIAL PRESSURE, bar 280 0 20 40 60 80 1100 260 1000 440-46 Low Viscosity
More informationPRODUCT SERVICE MANUAL FOR BK12DHZ PUMPS
PRODUCT SERVICE MANUAL FOR BK12DHZ PUMPS WARNING This manual, and the GENERAL INSTRUCTION MANUAL SRM00046, should be read thoroughly prior to pump installation, operation or maintenance. Manual No. SRM00095
More informationfranklinwater.com 50 Hz VR SERIES Vertical Multi-Stage Pumps
franklinwater.com 5 Hz VR SERIES Vertical Multi-Stage Pumps 5 HZ VR SERIES VERTICAL MULTI-STAGE PUMPS Features 2 Applications 2 Pump Specifications Counter-Flange Kits Motor Specifications 4 Ordering
More informationAP212HP Cast Iron Gear Pumps
Cast Iron Gear Pumps Standard and Low Noise series Reference: 200-P-991236-EN-01 Issue: 09.2016 1/56 Contents Page 1 General information... 5 1.1 External gear pumps components... 6 1.2 Technical data...
More informationThis instruction is valid for all ACE pump models shown on page 2
Screw pumps ACE3 Maintenance and Service Instruction This instruction is valid for all ACE pump models shown on page 2 Contents Page List of components 2 Exploded view 3 Ordering code/service intervals
More informationThis instruction is valid for all ACF/UCF pump models shown on page 2
Screw pumps ACF/UCF Maintenance and Service Instruction This instruction is valid for all ACF/UCF pump models shown on page 2 Contents Page List of components 2 Exploded view/ordering code/ Service intervals
More informationVIKING SG SERIES SEALLESS MAG DRIVE PUMPS
SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3. OPERATING RANGE: SG Pumps (Cast Iron Mag Drive) and SGN (Ductile Iron Mag Drive) Displacements No. 23 SG and 7 SGN 0.06 to 90 (SG) and
More informationVIKING SG SERIES SINGLE PUMPS (WITH SHAFT SEAL)
SERIES SG-04, -05, -07, -10, -14 () Page 341.1.1 OPERATING RANGE: SERIES SG-04/-05 PUMP SG Pumps (, Lip or Mechanical Sealed) Displacements No. 29 Flow Range Pressure Range Temperature Range Viscosity
More information- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL 302 MECHANICAL SEAL 303 BEARINGS 304 FITTINGS 305
CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART TABLE 202 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 3 ( 3-4-5-6 IMPELLERS ) 205 PERFORMANCE CURVE 3 ( 7-8-9 IMPELLERS
More informationSCM M2. Other advantages:
Sunfab s SCM 025-108 M2 is a range of robust axial piston motors with cartridge flange especially suitable for winch-, slewing-, wheel- and track drives. SCM 025-108 M2 is of the bent-axis type with spherical
More informationBSM ROTARY GEAR PUMPS
-SERIES FLG. MTD. PUMP PUMP FOOT The BSM -Series pumps are designed to provide quiet and efficient service at standard motor speeds, moderately high pressures. Typical applications are supplying hydraulic
More informationInstruction Manual & Parts List For H/G323FXFSX-500_ & 800_ Pumps With Flowserve Type BX Cartridge Seal
TM Instruction Manual & Parts List For H/G323FXFSX-500_ & 800_ Pumps With Flowserve Type BX Cartridge Seal WARNING This Special Instruction Manual and General Instructions Manual, CA-1, should be read
More informationProduct Service Manual For AA3G Series Pumps Size 187 Through 250
Product Service Manual For AA3G Series Pumps Size 187 Through 250 WARNING The IMO General Installation Operation, Maintenance and Troubleshooting Manual, (No. SRM00046), this manual, and associated component
More information5.1 MEDIUM HEAVY DUTY SERIES SIZE 2
.1 MEDIUM HEAVY DUTY SERIES SIZE 2 CONTENTS PGI100 Ordering Code.1.1 Medium Heavy Duty Series Technical Information.1.2 Specifications.1.3 Hydraulic fluids.1.4 Viscosity range.1. Temperature range.1.6
More informationScrew Pumps Series EMTEC HIGH-TECH FOR EMULSION. 20 DQ axial branch with pipe thread. 140 D8.6 radial branch with SAE flange
Screw Pumps 20 DQ axial branch with pipe thread HIGH-TECH FOR EMULSION 140 D8.6 radial branch with SAE flange Application For handling good, medium or mal-lubricating, abrasive fluids in cooling lubricant
More informationAlfa Laval three-screw pump
Alfa Laval three-screw pump Alfa Laval 3S pumps The 3S series is characterised by an innovative design for long service life, even in harsh operating conditions. The thoroughly engineered 3S series is
More informationSCM ISO. SCM ISO is a range of robust axial piston motors especially suitable for mobile hydraulics.
SCM 010-130 ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 ISO is of the bent-axis type with spherical pistons. The design results in a compact motor
More informationHydraulic Pump Series F1plus Fixed Displacement
Fixed Displacement Catalog 9129 8218-02 February 1999, GB Content General information, design 3 Specifications 4 Pump cross section 4 Pump and line selection 5 Ordering code 6 Standard versions 6 Installation
More informationSafety & Shut-off Blocks
Safety & Shut-off Blocks Description HYDAC safety and shut-off blocks are designed to protect, shut-off, and discharge hydraulic accumulators or user units. The compact design simplifies the hydraulic
More informationFluid Handling: Panel Unit
Fluid Handling: Panel Unit A permanently mounted, continuous-duty system for critical applications or difficult to access equipment. It also can serve as a maintenance station. The Overview The Panel Unit:
More informationUNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
SERIES 223A, 4223A, 323A, 4323A Page 1302.1 Issue B TABLE OF CONTENTS Features & Benefits...2 Jacketing...2 Relief Valve Configurations...3 Porting & Sealing...3 Revolvable Pump Casings...3 Cutaway View
More informationUNIVERSAL PRODUCT LINE: STAINLESS STEEL NON-JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE:
Page 1701.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Special Materials & Options
More informationSPUR GEAR PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1451 Page 1451.
Page 1451.1 TABLE OF CONTENTS Features & Benefits...2 Typical Applications...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Component
More informationPAHT pump PAHT X
MAKING MODERN LIVING POSSIBLE Data sheet PAHT pump PAHT X 674 444 danfoss.high-pressurepumps.com Table of Contents 1. Introduction...3 2. Benefits...3 3. Application areas...3 4. Technical data...4 5.
More informationUNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
SERIES 4223, 4323 (API 682 Seal) Section 304 Page 304. TABLE OF CONTENTS Features & Benefits...2 Revolvable Pump Casings...2 Materials of Construction...2 Cutaway View & Pump Features...3 Key...4 Specifications...4
More informationEaton PVM Variable Displacement Piston Pumps Vickers Product Line cc 3 ( in 3 )
Eaton PVM Variable Displacement Piston Pumps Vickers Product Line 18-141cc 3 (1.1-8.6in 3 ) Table of Contents M Series Variable Displacement Piston Pumps Introduction.... 3 Hydraulic System Design Calculations....
More informationHydraulic Pump Series F1 Fixed Displacement
Fixed Displacement Catalog 9129 8201-02 August, 1997 GB Content General information 3 Specifications 4 Pump and line selection 5 Ordering code 5 Standard versions 5 Installation dimensions 6 Installation
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.
More informationPVX-11 VANE PUMPS. See pages 12 thru 14 for PVX-11 dimensions. VARIABLE DISPLACEMENT, PRESSURE COMPENSATED PERFORMANCE SPECIFICATIONS
PVX-11 VANE PUMPS VARIABLE DISPLACEMENT, COMPENSATED NOTE: See pages thru 14 for PVX-11 dimensions. PERFORMANCE SPECIFICATIONS Displacement (Nominal) 1.5 in 3 /rev. (25 cm 3 /rev.) Displacement (Actual)
More information1½" GR Internal Eccentric Gear Pump
1½" GR Internal Eccentric Gear Pump Performance: Flow rate 5.7 m 3 /h Pressure 1-14 bar Temperature 0-200 C Speed 1400 d/d Viscosity 100-250000 SSU Technical Features: Internal eccentric gear pump 1½ threaded
More informationGEAR PUMPS DIMENSIONAL DETAILS
DIMENSIONAL DETAILS OUTLET INLET TYPE DISPLACEMENT CM 3 /REV FLOW AT 1500 REV/MIN MAX. WORKING PRESSURE MAX. SPEED DIMENSIONS MM P1 P2 P3 RPM L M D2 1.4 2.0 270 290 310 6000 40 79 D3 2.1 2.9 270 290 310
More informationSCM SAE. Other advantages: Sunfab s SCM SAE is a range of robust axial piston motors especially suitable for mobile hydraulics.
Sunfab s SCM 010-130 SAE is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 SAE is of the bent-axis type with spherical pistons. The design results in a compact
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.
More information"A" Series Variable Displacement Piston Pumps Single Pump, Pressure Compensator Type
A"A" Series PISTON PUMPS Single Pump, Compensator Graphic Symbol M O Specifications Model s A-FRB- A-FRC/H- A- -R-- - -K- A- -R-- - -K- A- -R-- - -K- A- -R-- - -K- A- R S- A9- R S- A- R S- Geometric Displacement
More informationNominal Flow. Pressure Range. Temp. Range. Viscosity Range. Nominal Flow. Pressure Range. Temp. Range. Viscosity Range. Stainless Steel.
Page 630.1 Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options Standard Pump (shown: KK124A) Operating Range 1 : Cast Iron Series: 124A/AE, 4124A/AE, 324A, 4324A, 224A/AE, 4224A/AE
More informationDuctile Iron, Jacketed Pumps: Catalog Section 1602 Cast Iron, Non-Jacketed Pumps: Catalog Section 1401 HL4126A
Page 1601.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Special Materials & Options
More informationIn Motion. A company presentation from I MO A B. A company presentation from IMO ab 1 A Colfax Business Unit
In Motion A company presentation from I MO A B A company presentation from IMO ab 1 A Colfax Business Unit 2 A company presentation from IMO ab Movement IMO AB, a Colfax Business Unit, is the leading manufacturer
More informationPRODUCT SERVICE MANUAL FOR. F312XICR-312_, 325_, 400_ and 437_ Pumps. For Solar Turbines
PRODUCT SERVICE MANUAL FOR F312XICR-312_, 325_, 400_ and 437_ Pumps For Solar Turbines WARNING This manual and the General Installation, Operation, Maintenance and Troubleshooting Manual (SRM00046) should
More informationCVM. EBARA PUMPS EUROPE S.p.A. MULTISTAGE CENTRIFUGAL PUMPS
CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE A (UP TO 0.6 kw) 203 PERFORMANCE CURVE A (FROM 0.75 kw UP TO 1.1 kw) 204 PERFORMANCE CURVE
More informationTruck Hydraulics. Series F1, F2, T1 Fixed Displacement Pumps
Series F1, F2, T1 Fixed Displacement Pumps aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Contents Hydraulic Pumps,
More informationCoolers. OK Series. Air Cooled Oil Coolers Hydraulic Symbol OK 1-11 OKF Cooling Systems Catalog. Applications
OK Series Air Cooled Oil Coolers Hydraulic Symbol OK 1-11 OKF 3-11 OKA 4-6 OKAF 4-6 OKA 8-11 OKAF 8-11 Description The OK Series cooler design uses a axial fan assembly which draws air through the cooler.
More informationProduct Manual. VIKING EN397-4a 2009
Product Manual VIKING EN397-4a 29 One partner all over the world Hägglunds Drives is one of the worlds leading manufacturer of heavy duty hydraulic drive systems. If what you need is Worldwide distribution
More informationProduct Manual VIKING. EN397-3a 1999
Product Manual VIKING EN397-3a 1999 One partner all over the world Hägglunds Drives is one of the worlds leading manufacturer of heavy duty hydraulic drive systems. If what you need is low speed and high
More informationAPP S 674 pumps APP S / APP S APP S
MAKING MODERN LIVING POSSIBLE Data sheet APP S 674 3.0-3.5 / APP S 674 5.1-9.0 APP S 674 21-38 ro-solutions.com Table of Contents 1. Introduction...3 2. Benefits...3 3. Application areas...3 4. Technical
More informationLowara. Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733. SH Series. 60 Hz
Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733 SH Series 60 Hz SERIE SH HYDRAULIC PERFORMANCE RANGE AT 60 Hz WEB 10-2006 2 CONTENTS 5 Specifications... 6
More informationLUBE OIL PUMPS. Critical Lubrication Service for: Bearings Seals Gearboxes. on... Gas & Steam Turbines Compressors Engines Starting Packages
LUBE OIL PUMPS Critical Lubrication Service for: Bearings Seals Gearboxes on... Gas & Steam Turbines Compressors Engines Starting Packages LEADING SUPPLIER OF LUBE OIL PUMPS TO THE POWER GENERATION INDUSTRY
More information- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 MECHANICAL SEAL 302 BEARINGS 303
CONTENTS Page - SPECIFICATIONS 200 PERFORMANCE RANGE and SELECTION CHART 201 TYPE KEY and CURVE SPECIFICATIONS 202 PERFORMANCE CURVE 0.50 203 PERFORMANCE CURVE 0.80 204 PERFORMANCE CURVE 1.00 205 PERFORMANCE
More information- DIMENSIONS AND WEIGHT 400 PUMP MATRIX PUMP DRAWING MATRIX DIMENSION TABLE MATRIX PACKING 403
CONTENTS Page - SPECIFICATIONS 200-201 SELECTION CHART 202 SELECTION CHART TABLE 203 TYPE KEY AND CURVE SPECIFICATIONS 204 PERFORMANCE CURVE 3 ( 2-3-4-5 IMPELLERS ) 205 PERFORMANCE CURVE 3 ( 6-7-8-9 IMPELLERS
More informationBSM ROTARY GEAR PUMPS
FT. MTD. PUMP B-Series pumps are a good choice for a variety of recirculating, mixing, and transfer applications. Typical pumped liquids include solvents, resins, and petroleum products. These pumps are
More informationPressure Control Valves. General Description. Specifications. Ordering Information
Catalog HY14-3000/US Technical Information Control Valves Series RCP General escription Series RCP in-line pressure control valves are chiefly used as remote control valves. They limit system pressure
More informationVIKING UNIVERSAL SEAL PUMPS. Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options. Operating Range1: Nominal Flow Rates:
VIKING UNIVERSAL SEAL PUMPS Section 630 Page 630.1 Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options Operating Range1: Cast Iron Series 124A/AE, 4124A/AE, 4124B, 324A, 4324A, 224A/AE,
More informationLIQUID-SPECIFIC PRODUCT LINE: STAINLESS STEEL VANE PUMPS PRODUCT DESCRIPTION SERIES OPERATING RANGE 1 NOMINAL FLOW RATES 2
Page 445.1 PRODUCT DESCRIPTION SERIES OPERATING RANGE 1 Rotary vane pumps are used for liquid transfer in applications ranging from chemicals to LP gas. Vanes extend from slots on the rotor, sweeping liquid
More informationModel 133 Models 134 & 135 AURORA 130 SERIES SINGLE STAGE TURBINE TYPE PUMPS
Model Models 4 & AURORA 0 SERIES SINGLE STAGE TURBINE TYPE PUMPS WWW.AURORAPUMP.COM AURORA 0 SERIES Single Stage Turbine Type Pumps Capacities to 0 G.P.M. Heads to 700 Ft. Temperatures to F A Pioneer in
More informationHydraulics. Axial Piston Pumps Series PVP. Introduction. With thru shaft option for multiple pump options Swash plate type for open circuit
Introduction *not included Pump with standard compensator, code: "omit" With thru shaft option for multiple pump options Swash plate type for open circuit Pump with load sensing, code: "A" Mounting style
More informationProduct Numbering System Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC Pump Assembly, Types AC & AE
Index Sheet ITEM S Bulletin Product Numbering System... 1 Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC... 2 Pump Assembly, Types AC & AE... 3-4 Dimensions, Types AC & AE... 5-8 Selection Curves,
More information3D SERIES. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page
CONTENTS Page - SPECIFICATIONS 0 SELECTION CHART 1 TYPE KEY 3 PERFORMANCE CURVE SPECIFICATIONS 4 PERFORMANCE CURVE 32-125 5 PERFORMANCE CURVE 32-6 PERFORMANCE CURVE 32-0 7 PERFORMANCE CURVE 40-125 8 PERFORMANCE
More informationVIKING. Series LVP STAINLESS STEEL VANE PUMP. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 2016 PRODUCT DESCRIPTION SERIES OPERATING RANGE
Page 445.1 PRODUCT DESCRIPTION Rotary vane pumps are used for liquid transfer in applications ranging from chemicals to LP gas. Vanes extend from slots on the rotor, sweeping liquid through a cam-shaped
More informationBSM ROTARY GEAR PUMPS
FT. MTD. PUMP The Heavy Duty S-Series pumps are designed to handle a wide variety of liquids and are particularly suitable for bulk transfer applications where long life and dependable service is required.
More informationHydraulic Pump Series VP1 Variable Displacement
Variable Displacement Catalog 9129 8222-02 February 1999, GB Content Page General information 3 Design 3 Specifications 4 Ordering information 4 VP1 cross section 4 Installation dimensions 5 Line dimensioning
More informationBENT AXIS PISTON MOTORS SERIES HPM FLANGE ISO HPM. pag.3
ENT AXIS PISTON MOTORS SERIES HPM FLANGE ISO 3019-2 HPM pag.3 TECHNICAL FEATURES ENT AXIS PISTON MOTORS SERIES HPM FLANGE ISO 3019-2 TECHNICAL FEATURES Displacement cm 3 /rev 12 17 25 34 40 47 55 64 80
More informationEMTEC -C PUMPS FOR HIGH PRESSURE COOLANT SUPPLY
CAPABILITIES EMTEC -C PUMPS FOR HIGH PRESSURE COOLANT SUPPLY BRINGING NEXT LEVEL PERFORMANCE TO COOLANT PUMPS ALLWEILER 2 3 PUMP LIFE INTO YOUR MOST CRITICAL EQUIPMENT COOLANT PUMPS CAN SIGNIFICANTLY EXTEND
More informationACG/UCG 7. Maintenance and Service Instruction. Screw pumps. This instruction is valid for all ACG/UCG pump models shown on page 2
Screw pumps A Member of the COLFAX PUMP GROUP ACG/UCG 7 Maintenance and Service Instruction ACG1 ' IMO AB This instruction is valid for all ACG/UCG pump models shown on page 2 Contents Page List of components
More informationVickers 45. VMQ Series 30 Vane Pumps. Fixed Displacement, For Industrial and Mobile Applications (4.188)
[ (4.188) 49,4 (1.94) /21,8 /.86) 174,7/172,3 (6.88/6.78) 332,9/33,5 (13.11/13.1) "M" is marked if metric port threads No marking if inch port threads AS-568-152 O-ring Vickers 45 65,3 (2.57) 13 (5.1 VMQ
More informationMobile Hydraulic Pumps T6G, T67G, T6ZC. Denison Vane Technology, fixed displacement
Mobile Hydraulic Pumps T6G, T67G, T6ZC Denison Vane Technology, fixed displacement aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing
More informationD SERIES HYDRAULIC PUMP
uk distributor for D SERIES HYDRAULIC PUMP quality products for mechanical & fluid power jbj Techniques Limited, www.jbj.co.uk Introduction to Concentric D Series Hydraulic Pumps Concentric offers one
More information