SPi Vehicle Application Guide KEYS Pro SD2.

Transcription

1 SPi Vehicle Application Guide KEYS Pro SD2. KEYS vehicle applications Guide for the SPi This guide provides you with vehicle coverage information and processes for your SPi KEYS Pro subscription. For more guides visit the SP Diagnostics Support website and go to the Products KeyScan Documents section of the site. Version 1.001

2

3 Contents Contents... 1 Introduction to Key Programming... 4 Keys... 4 Remote Controls... 4 Audi, Seat, Skoda, Volkswagen - VAG... 5 Introduction... 5 Pin Extraction Software flow chart... 5 VAG Software flow chart... 6 KeyFob Programming Procedure (Remote)... 7 Daewoo Introduction Daewoo Software flow chart FIAT Introduction Fiat Software flow chart CAN Immobiliser Ford Introduction Ford Software flow chart Pats Ford Software flow chart Pats1 Escort & Courier Ford Software flow chart - Pats2 Petrol & Diesel Ford Software flow chart Pats Ford Software flow chart Pats3 SCP Galaxy KeyFob Programming Procedure (Remote) Programming procedure using Master Key Ford Coded Access Using the Pincode Access on the SPi handset Connecting back into the vehicle to complete the process GM / Opel Introduction GM Software flow chart Immo GM Software flow chart Immo GM Software flow chart Remote Fob Programming GM Software flow chart Immobiliser 3 (CAN) GM Software flow chart Immobiliser 4 (Corsa-D) HONDA Introduction Honda Software flow chart Honda Key Fob Programming Procedure (Remote) Mitsubishi Introduction Mitsubishi Software flow chart Mitsubishi L200 Software flow chart Mitsubishi L200 Remote Software flow chart Mitsubishi Colt 2003 Onwards Software flow chart

4 NISSAN Introduction NATS 5 Software flow chart Key Fob Programming Procedure (Remote) LandRover Introduction LandRover Software flow chart LandRover CCU Software flow chart PSA Introduction PSA Software flow chart BSI PSA Software flow chart BSI-2, BSI-3 & BSI-4 systems, CAN Bsi PSA Software flow chart Old BSI PSA Software flow chart Immo Key Fob Programming Procedure (Remote) BSI Wake-Up procedure BSI activation Renault Introduction Program Keys Software Flow chart Clio 1, Kangoo 1, Laguna 1, Master Program Keys Software Flow chart Clio 2, Espace, Kangoo 2, Laguna 2, Master 2, Traffic Program Keys Software Flow chart Megane 1, Scenic Program Keys Manual Process Megane 1, Scenic Key Fob Programming Procedure (Remote) Rover Introduction Read EKA Code flow chart AS Program Remote flow chart Pektron Program Remote flow chart Immobiliser matching flow chart KeyFob Programming Procedure (Remote) Re-initialising Procedure AS Manual Coding SAAB Introduction SAAB Software flow chart

5 Subaru Introduction Subaru Software flow chart KeyFob Programming Procedure (Remote) Suzuki Introduction Program Keys Software flow chart Key Fob Programming Procedure (Remote) Toyota / Lexus Introduction Program Keys Software flow chart Erase Key Software flow chart Key Fob Programming Procedure (Remote) Applications List

6 Introduction to Key Programming Keys Many of today s vehicles have coded engine immobiliser systems, which are designed to immobilise the vehicle by disabling many of the vehicle s electrical circuits, including starter motor, ignition and fuel systems. The vehicle s immobiliser system is disarmed by the use of the vehicle s coded key which is programmed to the immobiliser system. The vehicle s key s contains a (Transponder) code that must match the code in either the vehicles Immobiliser system or Engine Management System (EMS). Every time the vehicle is started, the immobiliser system checks to see if the code from the key is correct. Until now the vehicle would need to be returned to the manufacturer s Main Dealer to have additional keys added to the vehicle. Using the ikeys application software you are now able to buy a replacement key and program it to successfully start the vehicle. The sequence for programming the key is very specific and must be carried out exactly as described on the ikeys application software. Some vehicles require a security code to be entered before you can successfully program an additional key, and these are usually supplied with the vehicle. If the security code has been misplaced or lost then you will be required to obtain the security code from the manufacturer. For the Volkswagen Audi Group (VAG), the ikeys software is able to automatically extract the security code from the vehicle. This can be done from the Engine management system EMS. Once you know this code you can make the correct selection and extract the security codes for the vehicle. Some vehicles have a time delay, so if an incorrect security code is entered, the system will prevent any further attempts for programming until a specified period of time has elapsed. Therefore it is important to be sure you are entering the correct security code for the vehicle. VAG allow you to attempt to enter the security code a defined number of times according to the immobiliser system fitted to the vehicle before applying the time delay. Remote Controls Many of today s vehicles have remote controls (key fobs) that enable you to turn off the alarm and operate the central locking system to open / close the doors without using the key. These remote controls also need to be programmed, when ever the battery is replaced / new remote control is purchased. There are different methods employed to carry out these programming procedures, which are either through a manual process or a diagnostic software process. Again these procedures are very precise and require the user to follow the procedure exactly, to program the remote control. 4

7 Audi, Seat, Skoda, Volkswagen - VAG Introduction VAG immobiliser systems use a 4 digit security code to access the vehicle s Key programming procedures. This will be a 4 digit security code that would have been supplied on a white tag when the vehicle was new. VAG main dealers do not have the ability to supply the security code without the car being present and connecting the VAG online diagnostic system to extract the security code from the vehicle. For this reason the ikeys Software is supplied with the VAG Pin Extraction software to enable you to extract the security code from the vehicle. We currently support 2 methods Engine and Dashboard Engine This will work on most petrol vehicles that have the engine management system ECM type ME7.x and all Diesel systems that have the engine management system ECM type EDC15x fitted (where x is the EMS system variation). Dashboard This method will supply a Pin code for vehicles fitted with a supported VDO dashboard. Once you have extracted the Security code from the vehicle you will then be able to successfully program the new key. Before programming the new key, ensure all the existing keys for the vehicle are available. As the procedure for programming a new key, will erase all the existing keys from the immobiliser system and require the existing keys to be re-programmed back into the vehicle. Pin Extraction Software flow chart INITIALISING READING MEMORY PLEASE WAIT PIN CODE UNABLE TO EXTRACT PIN CODE. PLEASE IDENTIFY YOUR DASHBOARD AND TRY VEHICLE SPECIFIC EXTRACTION 1234 TURN IGNITION OFF 5

8 VAG Software flow chart NOTE ENSURE ALL KEYS ARE PRESENT BEFORE PROCEEDING AND YOU HAVE OBTAINED THE 4 DIGIT PIN CODE INITIALISING KEY PROGRAMMED SUCCESSFULLY REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON PROGRAMMING KEY -----PART NUMBER----- XXXXXXXX XXXXXXXXXXXXX XXXX SELECT FUNCTION: 1)READ CODES 2)CLEAR CODES 3)PROGRAM KEYS KEY PROGRAMMED SUCCESSFULLY ENTER PIN CODE: XXXX PIN NOT ACCEPTED <ESC> LOGIN SUCCESSFUL KEY CODING FAILED ENTER NUMBER OF KEYS TO PROGRAM: 2 If more than 1 Key programmed PROGRAMMING KEY 6

9 KeyFob Programming Procedure (Remote) Audi A Volkswagen Lupo Audi A Volkswagen Polo 02 on Audi A Seat Ibiza 02 on Audi TT Seat Cordoba 02 on Audi A Seat Toledo Audi A4 01 on Seat Leon Seat Arosa Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Press and release either the Lock or Unlock button on the key fob. Typical VAG 2-button Key fob Typical VAG 3-button Key fob Within the next 30 seconds: Using the key manually lock and unlock the driver s door. Key fob is re-initialised. Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Seat Ibiza Seat Cordoba Seat Toledo Re-initialising Procedure Infrared Key fobs Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Point key fob at infrared receiver located in rear view mirror Press both the Lock and Unlock buttons together on the key fob twice 7

10 Typical VAG 2-button Key fob Typical VAG 3-button Key fob Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Re-initialising Procedure Radio frequency Key fobs Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Press both the Lock and Unlock buttons together on the key fob twice Typical VAG 2-button Key fob Typical VAG 3-button Key fob Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Skoda Octavia Volkswagen Beetle 98 on Volkswagen Golf Volkswagen Bora Re-initialising Procedure (01-04 vehicles only) Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Skoda Octavia s manufactured before 2001, can not be re-initialised and require programming. Refer to programming section. Press either the Lock or Unlock button on the key fob 8

11 Typical VAG 2-button Key fob Typical VAG 3-button Key fob Within the next 60 seconds: Manually Unlock driver s side door Key fob is re-initialised. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Repeat above procedure to re-initialise any remaining key fobs Skoda Superb 02 on Volkswagen Sharon 97 on Re-initialising Procedure Radio frequency key fobs (Type 2) Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Press either the Lock or Unlock button for 1 second on the key fob Typical VAG 2-button Key fob Typical VAG 3-button Key fob Manually Unlock or Lock the vehicle using the key Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. 9

12 Daewoo Introduction Daewoo Key programming does not require a pin code. All the keys need to be present when coding a key, any key not present will be erased. To Erase a lost key Program all remaining keys. If after programming a key the vehicle does not start, wait 10 Minutes and try again, or Disconnect battery for 10 Minutes. 10

13 Daewoo Software flow chart INITIALISING SWITCH IGNITION OFF ENTER NUMBER OF KEYS TO PROGRAM: -[ ]- 2 PROGRAMMING KEY SWITCH IGNITION ON... Cycle 3 times REMOVE KEY. INSERT NEXT KEY AND SWITCH IGNITION ON WITHIN 10sec -[ ]- PROGRAMMING KEY INSERT FIRST KEY & TURN IGNITION ON KEY PROGRAMMED SUCCESSFULLY 11

14 FIAT Introduction Fiat Key programming requires a 5 digit Pin number, this can be found on the Key card provided with the vehicle or obtained from the Dealer. All the keys need to be present when coding a key, any key not present will be permanently erased. To erase a lost key Program all remaining keys. 12

15 Fiat Software flow chart CAN Immobiliser ENTER PIN CODE: XXXX ENTER NUMBER OF REMOTES TO PROGRAM: <ESC> 2 ENTER NUMBER OF KEYS TO PROGRAM: 2 PLEASE COMPLETE PROGRAM OPERATIONWITHIN 15 SECS ANY KEY NOT PRESENT WILL BE DELETED CONTINUE? NO YES PRESS AND HOLD REMOTE FOR 3 SECONDS PROGRAMMING KEY PLEASE WAIT... SWITCH IGNITION OFF AND REMOVE KEY FROM IGNITION. INSERT NEXT KEY & TURN IGNITION ON NUMBER OF REMOTE(S) PROGRAMMED: 1 THERE ARE 3 KEYS PROGRAMMED DO YOU WANT TO PROGRAM REMOTES? NO YES yes 13

16 Ford Introduction Ford has a number of different systems fitted across the range. These are known as PATS (Passive Anti-Theft System) and have timed access or coded access in order to gain security the vehicle. This timed access can vary from 8 minutes to 12 minutes. Coded access is a system where the vehicle gives you a Out-Code and requires you to input an In- Code this is supplied by the Ford Dealer from the out code. The ikeys software will allow you to re-enter an In-Out Pair for a vehicle, this is a Out-code obtained from the vehicle and a In-code obtained from Ford. A matching pair will always be valid for that vehicle. Once the system has gained access you are able to program the keys to the vehicle. A minimum of 3 Keys must be programmed to the PATS 1 system before the vehicle will start, and 2 Keys to the PATS 2 and PATS 3 systems before the vehicle will start. 14

17 Ford Software flow chart Pats1 INITIALISING THERE ARE 2 KEYS PROGRAMMED SWITCH IGNITION OFF SWITCH IGNITION ON... ENTER NUMBER OF KEYS TO PROGRAM: 2 WAITING FOR SECURITY ACCESS COUNTDOWN: 7Min(s) 00Sec(s) SWITCH IGNITION OFF SWITCH IGNITION ON... PROGRAM NEXT KEY KEYS PROGRAMMED SUCCESSFULLY 15

18 Ford Software flow chart Pats1 Escort & Courier TO PROGRAM A NEW SET OF KEYS ONE 'RED' MASTER AND TWO SLAVE KEYS ARE REQUIRED. SWITCH IGNITION OFF SWITCH IGNITION OFF INSERT 'RED' MASTER KEY AND SWITCH IGNITION ON. INITIALISING SWITCH IGNITION ON... UNABLE TO OBTAIN SECURITY ACCESS. UNABLE TO OBTAIN SECURITY ACCESS. WAITING FOR SECURITY ACCESS COUNTDOWN: 8Min(s) 00Sec(s) WAITING FOR SECURITY ACCESS COUNTDOWN: 16Min(s) 00Sec(s) PROGRAMMING KEY REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON SWITCH IGNITION OFF PROGRAMMING KEY SWITCH IGNITION ON... PROGRAMMING COMPLETE! 16

19 Ford Software flow chart - Pats2 Petrol & Diesel ENTER NUMBER OF KEYS TO PROGRAM: 3 INSERT 'RED' MASTER KEY AND SWITCH IGNITION ON. INITIALISING Diesel WAITING FOR SECURITY ACCESS COUNTDOWN: 8Min(s) 00Sec(s) WAITING FOR SECURITY ACCESS COUNTDOWN: 8Min(s) 00Sec(s) Petrol UNABLE TO OBTAIN SECURITY ACCESS. RIM SUCCESSFULLY ERASED SWITCH IGNITION OFF AND REMOVE KEY FROM IGNITION. INSERT 'RED' MASTER KEY AND SWITCH IGNITION ON. Cycle for all keys REMOVE KEY. INSERT NEXT KEY AND SWITCH IGNITION ON WITHIN 10sec SWITCH IGNITION OFF PROGRAMMING COMPLETE! 17

20 Ford Software flow chart Pats3 REMOVE KEY FROM IGNITION INSERT KEY TO PROGRAM AND SWITCH IGNITION ON. ENTER NUMBER OF KEYS TO PROGRAM: 2 NOTE: Some 2004 > vehicles use in / out code security that must be obtained from a Ford dealership. INITIALISING UNABLE TO OBTAIN SECURITY ACCESS. VEHICLE OUTCODE: ENTER IN-CODE: Coded Access Timed Access WAITING FOR SECURITY ACCESS COUNTDOWN: 10Min(s) 0Sec(s) If time limit exceeded UNABLE TO OBTAIN SECURITY ACCESS PROGRAMMING KEY PLEASE WAIT Fail KEY CODING FAILED KEY PROGRAMMED SUCCESSFULLY REMOVE KEY. INSERT NEXT KEY AND SWITCH IGNITION ON WITHIN 10sec Fail REGISTRATION FAILURE. TIME EXCEEDED. 18

21 Ford Software flow chart Pats3 SCP Galaxy INSERT KEY TO PROGRAM AND SWITCH IGNITION ON. INITIALISING WAITING FOR SECURITY ACCESS COUNTDOWN: 8Min(s) 0Sec(s) If time limit exceeded REGISTRATION FAILURE, TIME EXCEEDED. INITIALISING Fail KEY CODING FAILED KEY PROGRAMMED SUCCESSFULLY 19

22 KeyFob Programming Procedure (Remote) Sport Ka Street Ka 03 on 03 on Fiesta Fiesta Fusion 02 on 02 on Mondeo 01- Cougar Focus C Max 03 on Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Close all doors Switch the ignition ON 4 times within 6 seconds Switch the ignition OFF Programming mode activated for approximately 10 seconds: o Press and release any button on the key fob Typical 3-button key fob Later style 3-button key fob o An audible warning will sound and the system Alarm LED will flash to indicate successful programming After the first key has been programmed, the 10 seconds programming mode automatically starts again for the next key Repeat above procedure to re-program any remaining key fobs. To exit programming mode: Switch ignition ON or wait 10 seconds Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 4 key fobs can be programmed to the vehicle. 20

23 Fiesta Mondeo Puma Programming Procedure Infrared key fobs Note. If the central locking / alarm system is malfunctioning, key fob batteries have been replaced or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Obtain all keys fitted with remote key fob for vehicle Using any key, switch the ignition to position I Wait approximately 10 seconds System Alarm LED should illuminate Note. System Alarm LED illuminates for approximately 5 seconds Whilst system Alarm LED is illuminated: o Switch the ignition OFF and remove the key Programming mode activated for approximately 20 seconds (System alarm LED remains illuminated): o o Point the key fob at the infrared receiver Fiesta and Puma: located near interior lamp Mondeo: located in front door handles Press and hold the Unlock button on the key fob Typical 3-button key fob Typical 2-button key fob o o o o After approximately 1 second, the LED on the key fob will flash once Press and release the Lock button on the key fob between 3 to 5 times, whilst still holding in the Lock button on the key fob Release the Unlock button on the key fob Continue to point the key fob at the infrared receiver until both the system Alarm LED and key fob LED have flashed 5 times Repeat above procedure to re-program any remaining key fobs. To exit programming mode: Switch ignition ON and OFF and wait approximately 20 seconds Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. 21

24 Note. A maximum of 4 key fobs can be programmed to the vehicle. Programming Procedure Radio frequency key fobs Fiesta and Puma vehicles only Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Obtain all keys fitted with remote key fobs Switch the ignition ON 4 times within 3 seconds Switch the ignition OFF and remove key from ignition switch Programming mode activated for approximately 20 seconds (System alarm LED remains illuminated): o Type 1 key fob: Press and release either the Lock or Unlock button on the key fob Typical 2-button key fob o Type 2 Key fob: Press and release any button on the key fob 22

25 Typical 3-button key fob According to model: Wait for either the System Alarm LED or Fog lamps ON warning lamp to illuminate and / or the vehicle to emits an audible warning sound to indicate correct programming Within 20 seconds: Repeat above procedure to re-program any remaining key fobs. To exit programming mode: Switch ignition ON and wait 20 seconds Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 4 key fobs can be programmed to the vehicle. Focus Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Obtain all keys with remote key fobs Fasten all seat belts and close all doors Switch the ignition between position I to position II 4 times within 6 seconds Switch the ignition to position I (up to 11/2000) or Switch the ignition OFF 12/2000 on Programming mode activated for approximately 10 seconds: o Press and hold either the Lock, Unlock or boot release button on the key fob Typical 3-button key fob 23

26 An audible warning will sound to indicate successful programming Within the next 10 seconds: Repeat above procedure to re-program any remaining key fobs To exit programming mode: Switch the ignition to position III or wait 10 seconds Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 4 key fobs can be programmed to the vehicle. Mondeo Programming Procedure Infrared key fobs Note. If the central locking / alarm system is malfunctioning, key fob batteries have been replaced or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Obtain all keys fitted with remote key fob for vehicle Fasten seat belts and close all doors Using any key, switch the ignition from position I to position II at least 4 times in 6 seconds Programming mode activated for approximately 10: o Point the key fob at the infrared receiver (located in front door handles) o Press and hold either the Lock or Unlock button on the key fob Typical 3-button key fob Typical 2-button key fob An audible warning will sound to indicate successful programming Within the next 10 seconds: Repeat above procedure to re-program remaining key fobs To exit programming mode: Start the engine and wait 10 seconds Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 4 key fobs can be programmed to the vehicle. Programming Procedure Radio frequency key fobs 24

27 Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Obtain all keys fitted with remote key fobs Switch the ignition ON 4 times within 3 seconds Switch the ignition OFF and remove key from ignition switch Programming mode activated for approximately 20 seconds (System alarm LED remains illuminated): o Type 1 key fob: Press and release either the Lock or Unlock button on the key fob Typical 2-button key fob o Type 2 Key fob: Press and release either the Lock or Unlock button on the key fob Typical 3-button key fob The system Alarm LED will flash to indicate successful programming Wait 2 seconds Within 20 seconds: Repeat above procedure to re-program remaining key fobs. To exit programming mode: Switch ignition ON and wait 20 seconds Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 4 key fobs can be programmed to the vehicle. 25

28 Tourneo Connect Transit Connect 02 on 02 on Transit Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Obtain all keys fitted with remote key fobs Switch the ignition from OFF to ON 8 times within 10 seconds Leave the ignition in the ON position Programming mode activated - doors Lock and then unlock Within 20 seconds: o Press and release any button on the first key fob to be programmed Typical 3-button key fob o Doors Lock and then Unlock to indicate correct programming Within 20 seconds: o Press and release any button on the second key fob to be programmed o Doors Lock and then Unlock to indicate correct programming Within 20 seconds: o Press and release any button on the third key fob to be programmed o Doors Lock and then Unlock to indicate correct programming Within 20 seconds: o Press and release any button on the fourth key fob to be programmed o Doors Lock and then Unlock to indicate correct programming 26

29 To exit programming mode: Switch ignition OFF Doors Lock and then Unlock to indicate programming mode end Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 4 key fobs can be programmed to the vehicle. Galaxy Programming Procedure Infrared key fobs Note. If the central locking / alarm system is malfunctioning or a replacement battery is installed or key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Close all windows and doors Insert one of the keys into the driver s side door lock Within 5 seconds: Turn key to Unlock position 3 times Note. Insure key is held in Unlock position for at least 0.5 seconds. Remove key from driver s side door lock Programming mode activated with driver s door LED illuminated Carry out the following within 15 seconds: o Point key fob at infrared receiver (located near rear view mirror) o Press and hold the Lock button on the key fob within 5 seconds of entering programming mode Typical 2-button key fob Later type 2-button key fob Typical 2-button key fob (to be edited) o Press the Unlock button 3 times on the key fob o Release the Lock button on the key fob o Correct programming of key fob indicated by driver s door LED flashing 6 times and key fob LED flashing 5 times o Repeat above procedure within 15 seconds to re-program any remaining key fobs. o To exit programming mode and turn OFF driver s side door LED: wait 15 seconds without pressing any key fob buttons. 27

30 o Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 4 key fobs can be programmed to the vehicle. Programming Procedure Radio frequency key fobs Note. If the central locking / alarm system is malfunctioning or a replacement battery is installed or key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Close all windows and doors Insert one of the keys into the driver s side door lock Within 5 seconds: Turn key to Unlock position 3 times Note. Insure key is held in Unlock position for at least 0.5 seconds. Remove key from driver s side door lock Programming mode activated with driver s door LED illuminated Carry out the following within 15 seconds: o Press and hold the Lock button on the key fob within 5 seconds of entering programming mode Typical 2-button key fob Later type 2-button key fob o Press the Unlock button 3 times on the key fob o Release the Lock button on the key fob o Correct programming of key fob indicated by driver s door LED flashing 6 times and key fob LED flashing 5 times o Repeat above procedure within 15 seconds to re-program any remaining key fobs. o To exit programming mode and turn OFF driver s side door LED: wait 15 seconds without pressing any key fob buttons. o Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 4 key fobs can be programmed to the vehicle. 28

31 Maverick 97 to 03 Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Obtain all keys fitted with remote key fobs Note. All previous key fobs will be erased when programming mode is entered. Switch the ignition from OFF to ON 8 times within 10 seconds Leave the ignition in the ON position Programming mode activated - doors Lock and then unlock Within 7.5 seconds: o Press and release any button on the first key fob to be programmed o Doors Lock and then Unlock to indicate correct programming Within 7.5 seconds: o Press and release any button on the second key fob to be programmed o Doors Lock and then Unlock to indicate correct programming Note. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again. Within 7.5 seconds: o Press and release any button on the third key fob to be programmed o Doors Lock and then Unlock to indicate correct programming Within 7.5 seconds: o Press and release any button on the fourth key fob to be programmed o Doors Lock and then Unlock to indicate correct programming To exit programming mode: Switch ignition OFF or wait up to 5 minutes Doors Lock and then Unlock to indicate programming mode end Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. 29

32 Programming procedure using Master Key Note. If the central locking / alarm system is malfunctioning or a replacement key is obtained. The following programming procedure is required to be carried out before the key will operate correctly. Obtain all keys Turn master key to position II Wait until clock LED illuminates Switch Ignition Off Wait until LED illuminates goes on and then Off Within 10 seconds - insert key new and switch ignition on LED flashes once to indicate correct programming Switch ignition off remove key Repeat for all other keys 30

33 Ford Coded Access Using the Pincode Access on the SPi handset 1. Navigate to the appropriate vehicle and select the Keycoding option. Once the system has established communications you will be presented with a screen similar to this. 2. Select the Program keys option and follow the on screen instructions. You may be asked to remove the Key from the ignintion and insert the New key. In the case of the Ford software you are able to select 2 methods of obtaining the Code for the vehicle. 3. If you select the PC Suite option you will be required to enter the VIN for the vehicle. It is important that the correct VIN is entered as this will be verified during the internet connection stage before obtaining the information required to gain security access to the vehicle. 4. You will then be asked to unplug the unit and use the Spi Suite to upload the information to our servers for processing. 31

34 Connecting the SPi handset to the Spi Suite to get the required information 5. Start the SPi Suite using either the SP Diagnostics SPi Suite icon on your desktop or on your start menu (Start > All Programs > SP Diagnostics > SPi Suite). 6. From the main screen click: 7. Connect your SPi as shown and click 32

35 8. The Spi Suite will then connect to the internet: 9. You will then be required to enter details of the vehicle you are currently working on. Some of this information will be provided from your Spi: 10. Once the process is completed you will be able to unplug the Spi and back into the vehicle you are working on to finish the pincode process: 33

36 Connecting back into the vehicle to complete the process 11. Follow steps 1 and 2 above. You will then be asked to verify the VIN code on the vehicle again to ensure the information we have provided matches with the vehicle you are programming the key on. 12. Security access will then be granted and you will be able to complete the process and program the Key or Keys into the vehicle. 34

37 GM / Opel Introduction The General Motors group use an immobiliser and Engine Management Systems to immobilise the vehicle. The immobiliser system is operated independently from the central locking system and its main function is to stop the vehicle from starting in the event that it does not recognise the transponder. The vehicle is supplied with a card that contains the security code for the vehicle. This should be located at the front of the service manual. Agila 02 on Programming Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following re-programming procedure. Open driver s side door Switch the ignition to the ON position for 1 second Within the next 10 seconds: Switch the ignition OFF and remove key Within 20 seconds either: Press and release door contact switch 3 times or close and open driver s side door 3 times (leaving door open) Switch the ignition to the ON position for 2 seconds Within 10 seconds: Switch ignition OFF and remove key Press and release the Unlock button on key fob 3 times Typical 2-button key fob Doors Lock and Unlock to indicate correct programming Repeat above procedure for all remaining key fobs Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 3 key fobs can be programmed to the vehicle. If there are only 2 key fobs available the first key must be programmed twice. 35

38 Corsa C Astra G Zafira Astra H 04 on Vectra B Omega Frontera Vectra C Signum Meriva 02 on 03 on 03 on Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following re-initialising procedure. Switch the ignition to the ON position Programming mode activated for 30 seconds Press either the Lock or Unlock button on the key fob to be programmed Typical 2-button key fob Typical 3-button key fob Central locking system operates to indicate correct re-initialising Repeat above procedure for all remaining key fobs Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. 36

39 GM Software flow chart Immo 1 INITIALISING UNABLE TO PROGRAM AS ALL TRANSPONDERS HAVE BEEN PROGRAMMED PROGRAM KEY TRANSPONDER KEY NO? ENTER PIN XXXX - BUSY - PROGRAMMING KEY TRANSPONDER ALREADY PROGRAMMED TRANSPONDER SUCCESSFULLY PROGRAMMED SWITCH OFF IGNITION AND REMOVE KEY INSERT KEY WITH IGNITION ON 37

40 GM Software flow chart Immo 2 INSERT KEY WITH IGNITION ON ARE YOU SURE YOU WANT TO PROGRAM KEYS? YES NO SWITCH IGNITION ON PROGRAMMING KEY SWITCH IGNITION OFF PROGRAM ADDITIONAL KEYS? YES NO YES NO KEY PROGRAMMED SUCCESSFULLY 38

41 GM Software flow chart Remote Fob Programming No IS SECURITY LOGIN REQUIRED? YES NO Yes ENTER PIN CODE: 0000 Fail PIN NOT ACCEPTED <ESC> ACTIVATE REMOTE SEVERAL TIMES NEXT TO RECEIVER Fail OPERATION FAILED. PROGRAM ADDITIONAL REMOTES? YES NO OPERATION SUCCESSFUL. 39

42 GM Software flow chart Immobiliser 3 (CAN) TO PROGRAM THE KEY PLEASE FIRST ENTER THE PIN CODE AND THEN FOLLOW THE INSTRUCTIONS. ENTER PIN CODE: 0000 <ESC> PIN NOT ACCEPTED Fail IS THIS THE CORRECT CODE: 1324 YES NO PLEASE INSERT A NEW KEY SWITCH IGNITION ON.. THEN PRESS DOES THE KEY HAVE A VIRGIN TRANSPONDER? YES NO UNABLE TO PROGRAM AS ALL 5 KEYS ARE PROGRAMMED Fail PROGRAMMING NEW KEY PLEASE WAIT OPERATION SUCCESSFUL. SWITCH OFF IGNITION AND REMOVE KEY REMOVE KEY FROM IGNITION DO YOU WANT TO PROGRAM ANOTHER? <ESC> OPERATION FAILED. Fail SWITCH IGNITION ON.. THEN PRESS 40

43 GM Software flow chart Immobiliser 4 (Corsa-D) All Keys must be present at the time of programming, any key not present will be erased. ENTER PIN CODE: 0000 <ESC> ENTER NUMBER OF KEYS TO PROGRAM: 2 REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON PROGRAMMING KEY Fail DATA COMMUNICATION HAS FAILED, PRESS TO RESTART OR <ESC> TO EXIT THERE ARE 2 KEYS PROGRAMMED 41

44 HONDA Introduction All Keys need to be present when programming keys, any key not present will be erased. No Security Code is needed to program keys. To Erase a lost key Program all remaining keys. 42

45 Honda Software flow chart NOTE - ENSURE ALL KEYS ARE PRESENT, ANY KEY NOT PRESENT WILL BE DISABLED. ENTER NUMBER OF KEYS TO PROGRAM: 2 SWITCH IGNITION OFF SWITCH IGNITION ON THEN PRESS INITIALISING REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON SWITCH IGNITION OFF SWITCH IGNITION OFF SWITCH IGNITION ON THEN PRESS SWITCH IGNITION ON THEN PRESS THERE ARE 2 KEYS PROGRAMMED 43

46 Honda Key Fob Programming Procedure (Remote) Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Maximum of 3 Remotes can be programmed Obtain all remote controls Switch the ignition ON Within 4 Seconds Press the Unlock or Lock Button Within 4 Seconds Switch the Ignition OFF Within 4 Seconds Switch the Ignition ON Within 4 Seconds Press the Unlock or Lock Button The system should Unlock or Lock the vehicle Within 4 Seconds Press the Unlock or Lock Button Within 15 Seconds - Press the Unlock or Lock Button of each remote that is to be programmed Switch the Ignition OFF Remove the Ignition Key Check the operation of each remote Fob. Lock Unlock Typical 2-button key fob 44

47 Mitsubishi Introduction All Keys need to be present when programming keys, any key not present will be erased. No Security Code is needed for Vehicle listed in the Software. To Erase a lost key Program all remaining keys. The Dashboard Warning lamp will flash while programming to indicate that the vehicle is in diagnostic mode. L200 Remotes are coded diagnostically via the separate menu Item. Colt 2003 Onwards Remotes are coded at the same time as the key. 45

48 Mitsubishi Software flow chart ENTER NUMBER OF KEYS TO PROGRAM: 2 SWITCH IGNITION OFF SWITCH IGNITION ON THEN PRESS INITIALISING PROGRAMMING KEY Fail PIN NOT ACCEPTED REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON PROGRAMMING KEY Fail KEY CODING FAILED THERE ARE 2 KEYS PROGRAMMED Pass KEY PROGRAMMED SUCCESSFULLY 46

49 Mitsubishi L200 Software flow chart ENTER NUMBER OF KEYS TO PROGRAM: 2 PROGRAMMING KEY Fail UNABLE TO OBTAIN SECURITY ACCESS. REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON KEY PROGRAMMED SUCCESSFULLY 47

50 Mitsubishi L200 Remote Software flow chart INITIALISING ACTIVATE REMOTE SEVERAL TIMES NEXT TO RECEIVER THERE IS ONE REMOTES PROGRAMMED 48

51 Mitsubishi Colt 2003 Onwards Software flow chart ENTER NUMBER OF KEYS TO PROGRAM: 2 PROGRAMMING KEY SWITCH IGNITION OFF AND REMOVE KEY FROM IGNITION. PROGRAMMING KEY INSERT FIRST KEY & TURN IGNITION ON REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON PROGRAMMING KEY Fail KEY CODING FAILED KEY PROGRAMMED SUCCESSFULLY 49

52 Key Fob Programming Procedure (Remote) Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Maximum of 2 Remotes can be programmed Connect a link wire between Pin 4 and Pin 1 on the J1962 Connector Close all Doors Turn Ignition to ACC position and the back to Off 3 Times with in 10 Seconds Doors Should lock then unlock Press remote control lock or Unlock button once Press remote control lock or Unlock button twice within 10 Seconds Doors Should lock then unlock Repeat for Second Remote J9162 Connector Vehicle Side 50

53 NISSAN Introduction The ikeys software supports the Nissan NATS5 immobiliser system, A 4 digit pin code is required to program keys for this system, and this is supplied with the vehicle, however if the Immobiliser label has a large letter A on it then the PIN is fixed to Note. Not all keys need to be present, as programming a key is adding that key to the system. The removal of all of the keys is a separate function in the ikeys software menu. 51

54 NATS 5 Software flow chart ENTER PIN CODE: 0000 <ESC> PROGRAMMING KEY PIN NOT ACCEPTED KEY PROGRAMMED SUCCESSFULLY 52

55 Key Fob Programming Procedure (Remote) Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Maximum of 4 Remotes can be programmed To enter programming mode Switch Ignition ON and OFF 6 times within 10 Seconds After 2 Seconds the indicators will flash two times Programming mode is active for 2 minutes. To Programme remotes Press and Hold Unlock button Press Lock button 3 times Release Unlock button Indicators will flash once to conform programmed correctly Repeat for all remaining remotes If 4 remotes have been programmed the indicators will flash 3 times If Less than 4 remotes programmed Switch Ignition On, Indicator lights will flash twice. Check Operation of all remotes Lock Unlock Typical NATS5 Key 53

56 LandRover Introduction The ikeys software supports the Immobiliser on CAN Protocol for Landrover vehicles using the CAN harness ( or V2) and the Landrover uniplexer ( ) No security pin is required; However a Programmed key or New Virgin Key is required to start the programming process. Remotes are Programmed Diagnostically. Freelander CCU Plips Programming requires all Plips to be present when programming, any not present will be erased from the vehicle. No Security pin is required.. Note. All keys need to be present; any key not present will be erased from the system. 54

57 LandRover Software flow chart PLEASE INSERT KEY INTO BARREL AT POSITION 0 ENTER NUMBER OF KEYS TO PROGRAM: 2 KEY IN IGNITION IS DISABLED UNABLE TO PROGRAM ALL KEYS NOT PRESENT WILL BE DELETED PROGRAMING PLEASE WAIT... INSERT NEXT KEY PLEASE SWITCH IGNITION TO POSITION 0 PLEASE SWITCH IGNITION TO POSITION 2 CLEAR COMPLETE PLEASE SWITCH IGNITION TO POSITION 0 PROGRAM COMPLETE CLEARING CODES PLEASE SWITCH IGNITION TO POSITION 2 55

58 LandRover CCU Software flow chart INITIALISING Yes ACTIVATE REMOTE SEVERAL TIMES NEXT TO RECEIVER PROGRAM ADDITIONAL REMOTES? 1)YES 2)NO PROGRAMMING COMPLETE! 56

59 PSA Introduction There are 3 different types of immobiliser systems that are used across the PSA range. These consist of the Standard Immobiliser System (Immo), the Passenger compartment protection control unit (CPH) and the Body systems interface (BSI). 57

60 PSA Software flow chart BSI-1 NOTE ENSURE ALL KEYS ARE PRESENT BEFORE PROCEEDING AND YOU HAVE OBTAINED THE 4 DIGIT PIN CODE ENSURE ALL VEHICLE DOORS ARE CLOSED ENTER PIN CODE: 0000 <ESC> FAILED TO PROGRAM KEY ENTER NUMBER OF KEYS TO PROGRAM: 2 REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON SWITCH IGNITION OFF SWITCH IGNITION OFF SWITCH IGNITION ON THEN PRESS SWITCH IGNITION ON THEN PRESS INITIALISING PROGRAMMING KEY KEY PROGRAMMED SUCCESSFULLY 58

61 PSA Software flow chart BSI-2, BSI-3 & BSI-4 systems, CAN Bsi NOTE ENSURE ALL KEYS ARE PRESENT BEFORE PROCEEDING AND YOU HAVE OBTAINED THE 4 DIGIT PIN CODE ENSURE ALL VEHICLE DOORS ARE CLOSED ENTER PIN CODE: 0000 <ESC> FAILED TO PROGRAM KEY ENTER NUMBER OF KEYS TO PROGRAM: 2 SWITCH IGNITION OFF REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON SWITCH IGNITION ON THEN PRESS SWITCH IGNITION OFF INITIALISING SWITCH IGNITION ON THEN PRESS KEY PROGRAMMED SUCCESSFULLY 59

62 PSA Software flow chart Old BSI ENSURE ALL VEHICLE DOORS ARE CLOSED ENTER NUMBER OF KEYS TO PROGRAM: 2 SWITCH IGNITION OFF SWITCH IGNITION ON THEN PRESS PIN NOT ACCEPTED INITIALISING SWITCH IGNITION OFF SWITCH IGNITION OFF REMOVE CURRENT KEY INSERT NEXT KEY AND SWITCH IGNITION ON KEY PROGRAMMED SUCCESSFULLY PROGRAMMING KEY 60

63 PSA Software flow chart Immo 1 ENTER PIN CODE: 1234 ENSURE ALL VEHICLE DOORS ARE CLOSED ENTER NUMBER OF KEYS TO PROGRAM: SWITCH IGNITION OFF REMOVE CURRENT KEY INSERT NEXT KEY SWITCH IGNITION ON THEN PRESS PROGRAMMING KEY INITIALISING SWITCH IGNITION OFF SWITCH IGNITION OFF PIN NOT ACCEPTED Fail PROGRAMMING KEY 61

64 Key Fob Programming Procedure (Remote) Citroen Saxo Peugeot Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Unlock the vehicle using the key Within 30 seconds, press key fob lock button twice Typical 2-button key fob Key fob is re-initialised. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Repeat above procedure to re-initialise any remaining key fobs. Citroen Xsara Picaso 99 on Peugeot on Citroen C3 02 on Citroen Belingo 02 on Peugeot Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Switch the ignition to the ON position Press and hold the Lock button on the key fob for 10 seconds. Release the lock button Typical 2-button key fobs 62

65 Switch the ignition to the OFF position Wait for approximately 5 seconds Key fob is re-initialised. Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Citroen Xsara Citroen Xantia Citroen Synergie Citroen Evasion Citroen Dispatch 98 on Citroen Jumpy 98 on Peugeot Citroen Belingo Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Switch the ignition to the ON position Wait for alarm system LED to turn OFF (if LED fitted) or wait for approximately 10 seconds (If LED not fitted) Within 30 seconds: Press either the Lock or Un-lock button on the key fob. Typical 2-button key fobs Within 10 seconds: Press either the Lock or Un-lock button on the key fob. Ensure alarm system LED (if fitted) turns ON for a split second. Key fob is re-initialised. Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. 63

66 Citroen Xsara Citroen 4 Citroen C Citroen 4 Re-initialising Procedure Note. If battery is replaced inside key fob / key fob has been re-programmed or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following re-initialising procedure. Switch the ignition to the ON position Press and hold the Lock button on the key fob for approximately 10 seconds Typical 3-button key fob Release the lock button Switch the ignition to the OFF position Wait for approximately 3 seconds Key fob is re-initialised. Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Citroen Relay 02 on Citroen 7 Citroen Jumper 02 on Citroen 7 Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Switch the ignition to the ON position Press and hold the Lock button on the key fob for approximately 10 seconds Typical 2-button key fob 64

67 Release the lock button Switch the ignition to the OFF position Wait for approximately 5 seconds Key fob is re-initialised. Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Peugeot Peugeot 2 Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Unlock the Drivers door using the key Press and hold the Lock / Unlock button on the key fob until the LED on the key fob stops flashing. Typical single button key fob Release the Lock / Unlock button on the key fob The LED on the key fob should remain illuminated Press and release the Lock / Unlock button on the key fob. The LED on the key fob should turn OFF Open the driver s side door and sit in the driver s seat. Close the driver s side door Hold the key fob next to the ignition switch Press and release the Lock / Unlock button on the key fob Switch the ignition to the ON position Wait 10 seconds Switch the ignition to the OFF position Wait 5 seconds Key fob is re-initialised. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Repeat above procedure to re-initialise any remaining key fobs. 65

68 Peugeot on Peugeot 12 Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Switch the ignition to the ON position using the key fob to be programmed Press and release the Lock button on the key fob Typical 4 button key fob Switch the ignition to the OFF position Key fob is re-initialised Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Peugeot on Peugeot 3 Peugeot on Peugeot 3 Peugeot 406 / Coupe Peugeot 3 Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Unlock the Drivers door using the key Press and hold the Lock / Unlock button on the key fob The LED on the key fob should start to flash Typical single button key fob Wait for approximately 20 seconds and then with the Lock / Unlock button still held, press and release the double locking button on the key fob. The LED on the key fob will stop flashing Release the Lock / Unlock button on the key fob The LED on the key fob will remain illuminated Press and release the Lock / Unlock button on the key fob The LED on the key fob will turn OFF 66

69 Open the driver s side door and sit in the driver s seat. Close the driver s side door Hold the key fob next to the ignition switch Press and release the Lock / Unlock button on the key fob Switch the ignition to the ON position Wait 10 seconds Switch the ignition to the OFF position Wait 5 seconds Key fob is re-initialised. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Repeat above procedure to re-initialise any remaining key fobs. Peugeot Peugeot 5 Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Unlock the Drivers door using the key Press and hold the Lock / Unlock button on the key fob The LED on the key fob should start to flash Typical 2-button key fob Wait for approximately 20 seconds and then with the Lock / Unlock button still held, press and release the double locking button on the key fob. The LED on the key fob will stop flashing Release the Lock / Unlock button on the key fob The LED on the key fob will remain illuminated Press and release the Lock / Unlock button on the key fob The LED on the key fob will turn OFF Open the driver s side door and sit in the driver s seat. Close the driver s side door Hold the key fob next to the ignition switch Press and release the Lock / Unlock button on the key fob Switch the ignition to the ON position Wait 10 seconds Switch the ignition to the OFF position Wait 5 seconds Key fob is re-initialised. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Repeat above procedure to re-initialise any remaining key fobs. 67

70 Peugeot 406 / Coupe Peugeot 8 Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Ensure ignition switch is in the OFF position Note. Vehicles fitted with double locking systems: Press both the Lock / Unlock and Double locking buttons on key fob together when carrying out the following procedure. Press and hold the Lock / Unlock button on the key fob until the LED on the key fob turns OFF Typical 2-button key fob Release the Lock / Unlock button on the key fob LED on key fob remains illuminated Press the Lock / Unlock button twice on the key fob Switch the ignition to the ON position Switch the ignition to the OFF position Wait 5 seconds Key fob is re-initialised Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Peugeot on Peugeot 9 Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Switch the ignition to the ON position Press and hold the Lock button on the key fob for 10 seconds 68

71 Typical 3-button key fob Switch the ignition to the OFF position Remove key from ignition switch Wait 5 seconds Key fob is re-initialised Repeat above procedure to re-initialised any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. Peugeot Partner 98 on Peugeot 13 Re-initialising Procedure Note. If battery is replaced inside key fob / key fob has been re-programmed or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following re-initialising procedure. Switch the ignition to the ON position Wait for alarm system LED to turn OFF (if LED fitted) or wait for approximately 10 seconds (If LED not fitted) Within 30 seconds: Press either the Lock or Un-lock button on the key fob. Typical 2-button key fob Ensure alarm system LED (if fitted) turns ON for a split second. Switch the ignition to the OFF position Remove key fob from ignition switch Key fob is re-initialised. Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. 69

72 Peugeot Boxer Peugeot 14 Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Switch the ignition to the ON position Press and hold either the Lock or Unlock button on the key fob for approximately 10 seconds Typical 2-button key fob Release the button on the key fob Switch the ignition to the OFF position Remove key from ignition switch Key fob is re-initialised. Repeat above procedure to re-initialise any remaining key fobs. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. 70

73 BSI Wake-Up procedure BSI activation The BSI can be woken up by activating certain functions i.e key Fob, opening a door, switching on the radio or opening the bonnet. When woken, it switches to full operating mode. On switching the ignition off it continues working for up to 2 minutes and then shuts itself down progressively taking a further 1 minute to enter 'Standby'/'Power Save' mode. If however the driver switched on a consumer with the engine not running, the BSI stays awake for thirty minutes (Economy Mode). Anything which interrupts the BSI's shut down operation can cause the problems mentioned in the above introduction. This is the reason for the 3 minute Wait time before disconnecting the battery. Procedure for Battery Disconnection (The 3 minute rule) 1. Whenever a vehicle battery has to be disconnected, switch off all equipment interior lights etc. close the doors leaving the driver's window down. 2. Switch off the ignition and remove the key and any diagnostic equipment if connected. 3. Wait 3-minutes before disconnecting the battery. The BSI must be allowed to go to sleep i.e into 'Power Save' mode. Do not operate any equipment on the vehicle during this time. Remember, even opening the bonnet will wake up the BSI on the vehicle fitted with an alarm. Procedure for Battery Reconnection Ensure that the procedure for battery disconnection has been adhered to and importantly all BSI functions were switched off with the driver's window left down. 1. Close all doors on the vehicle. 2. Remove the ignition key if left in the ignition. 3. Reconnect the battery. 4. Wait 10 seconds. 5. Switch on the headlights through the driver's window. You will hear a 'Bong'. 6. Switch on the ignition then start the vehicle and check systems are functioning correctly. 71

74 Renault Introduction The Renault s immobiliser system use a security code to access the Key programming procedures. Depending on the system this could be either 4, 8 or 12 digit security code and some vehicles may use an alpha-numeric security coding system. The security code can normally be found at the front of the service book, but failing this, the local Renault main dealer will supply you with this information for a nominal fee. All vehicles are fitted with a immobiliser LED system display light that indicates the status of the security system. There is a maximum number of keys that are able to be programmed to the vehicle, but this is dependant on the immobiliser system, but in general it varies between four and eight keys. Early Megane and Megane Scenic s with a IR Central locking has a Manual Process for Programming Keys Note. Not all keys need to be present as programming a key is adding that key to the system. 72

75 Program Keys Software Flow chart Clio 1, Kangoo 1, Laguna 1, Master 1 INITIALISING INSERT KEY WITH IGNITION ON 30 SECONDS ONLY THE KEY IN THE IGNITION WILL BE PROGRAMMED INITIALISING SWITCH IGNITION OFF SWITCH IGNITION ON SWITCH IGNITION ON SWITCH IGNITION OFF ENTER PIN CODE: 0000 KEY PROGRAMMED SUCCESSFULLY <ESC> SWITCH IGNITION OFF Note. There is no checking facility on the vehicle s immobiliser system to verify that the security code is correct. Please ensure you have entered the correct security code for the vehicle. 73

76 Program Keys Software Flow chart Clio 2, Espace, Kangoo 2, Laguna 2, Master 2, Traffic 2 INITIALISING ENTER NUMBER OF KEYS TO PROGRAM: 2 ENTER PIN CODE: <ESC> FAILED TO PROGRAM KEY SWITCH IGNITION OFF INITIALISING INSERT FIRST KEY & TURN IGNITION ON PROGRAMMING NEW KEY FAILED TO PROGRAM KEY INITIALISING KEY PROGRAMMED SUCCESSFULLY 74

77 Program Keys Software Flow chart Megane 1, Scenic 1 INITIALISING ENTER NUMBER OF KEYS TO PROGRAM: 2 ENTER PIN CODE: <ESC> SWITCH IGNITION OFF SWITCH IGNITION ON PROGRAMMING KEY REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON KEY CODING FAILED KEY PROGRAMMED SUCCESSFULLY 75

78 Program Keys Manual Process Megane 1, Scenic 1 1) Switch on the ignition 2) Press hold the central locking button on the dash, Immobiliser led starts to blink slowly 3) Count the blinks to enter the unlock code number, after the required number of blinks has been counted, that represent the individual number, make a short pause, then enter the next 4) Once the 4th number has been entered, the immobiliser LED will stay on for a few seconds, then go off, turn the ignition off, then press and hold the central locking button, the doors will lock and then unlock and the LED will stay on for a few seconds, during this time aim the plip key at the sensor and keep pressing until the doors lock and then unlock again. The car should have now programmed the key code. 5) Press and hold the central locking button to complete programming (doors will lock and then unlock). If you have no central locking button on the dash/centre consol, follow the above procedure but use the accelerator pedal, to start the sequence, and after each number has been input, press the button on the end of the wiper stalk 76

79 Key Fob Programming Procedure (Remote) Twingo 95 on Clio Extra Laguna Rapid Safrane Express Espace Kangoo 97 on Trafic (petrol) Scenic Master Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Renault key fobs are usually fitted with a serial number which is located under the cover inside the key fob and can be viewed after removing fixing screw. Note. Only key fobs fitted with an 8 character serial number can be programmed manually. Key fobs with a 5 character serial number do not require programming. All other variations on the number of characters used for the serial numbers require diagnostic equipment to program the key fobs. Ensure the ignition switch is OFF Press and hold in the central locking button inside the vehicle for a minimum of 5 seconds Vehicle doors should Lock and then Unlock Within the next 10 to 15 seconds: o On the first key fob: Press the Lock / Unlock button twice (can be once on some models) Typical Renault key fob o On the second key fob: Press the Lock / Unlock button twice (can be once on some models) Vehicle doors should Lock and then Unlock Key fobs are re-programmed. Confirm operation of key fob by locking and unlocking vehicle using key fob buttons. 77

80 Clio II 98 on Re-initialising Procedure Radio frequency key fobs only Note. If key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following re-initialising procedure. Ensure the ignition switch is OFF Press and hold in the central locking button inside the vehicle for a minimum of 5 seconds Vehicle doors should Lock and then Unlock Immobiliser LED illuminates Press the Lock / Unlock button on the key fob Typical Renault key fob Immobiliser LED turns OFF Key fob is re-programmed. Repeat above procedure for the second key fob Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Replacement key fobs can only be programmed using diagnostic equipment Refer to the ikeys software for further information. Note. A maximum of 2 key fobs can be programmed to the vehicle. Megane Re-initialising Procedure Radio frequency key fobs only Note. If key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following re-initialising procedure. Press and hold the Lock / Unlock button on the key fob for more than 10 seconds. Typical Renault key fob The red LED should extinguish. 78

81 Point the remote at the car and press the Lock / Unlock button on the key fob 3 times. Confirm the remote locks and unlocks the central locking system Programming Procedure Note. If the central locking / alarm system is malfunctioning or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. Replacement key fobs can only be programmed using diagnostic equipment Refer to the ikeys software for further information. Note. A maximum of 2 key fobs can be programmed to the vehicle. 79

82 Rover Introduction The method in which the Rover key programming is performed on these vehicles is slightly different, as it is the remote key fob (also known as the PLIP) that is programmed and not the actual key itself. The PLIP is used to arm or disarm the alarm on the vehicle (depending on the system fitted) and also activate the vehicle s central locking system. The coverage for these vehicles is dependant on the ikeys software ability to extract the randomly generated Emergency Key Access code (EKA) that is used to enable and disable the immobiliser / alarm system. This is useful to permanently disable the immobiliser/alarm for a length of time. After 3 failed attempts the system will not let you attempt this procedure again for 10 minutes (30 minutes for Land Rover). The other function on the ikeys software enables you to program a new PLIP to the vehicle. This is useful when the original PLIP has been broken or lost. Immobiliser Matching 5AS This function is for matching a replacement Immobiliser unit to the Engine ECU, The Plips must first be coded to the 5AS unit, and then the immobiliser can then be matched to the Engine ECU. Pektron BCU The Immobiliser must be disabled before communication can be made with the Pektron ECU. Any remote not present will be erased. Please Record the EKA as failing to program any remotes may result in the vehicle being immobilised and the only way to disable the immobiliser is with the EKA code. Only Existing remotes and New remotes supplied with the 22 digit barcode can be programmed (remove first and last digit of code when prompted). 80

83 Read EKA Code flow chart EKA - EMERGENCY KEY ACCESS CODE. THIS FUNCTION ENABLES AN OVERRIDE OF THE IMMOBILISER SYSTEM IF THE PLIP IS DAMAGED OR LOST. THIS ALLOWS THE VEHICLE TO BE USED WHILE A NEW PLIP IS OBTAINED. ENTER THE CODE BY TURNING THE KEY IN THE DRIVERS SIDE DOOR. INITIALISING READING EMERGENCY KEY ACCESS CODE... (EKA). TURN KEY TO POSITION FOR THE FOLLOWING UNLOCK 1, LOCK 2, UNLOCK 3, LOCK Insert the ignition key into the drivers side door lock. 2. Turn and hold the key clockwise to the locking position (the doors will lock) for at least 5 seconds. 3. Return the key to a central upright position. 4. Enter the First Digit - Turn the key fully, anticlockwise to the unlock position (the doors will unlock) then back to the central position. This should be done the amount of times as the first digit of the EKA Code. 5. Enter the second digit - Turn the key fully, clockwise to the lock position then back to the central position for the number of times of the second digit of the EKA Code. 6. Enter the third digit - Turn the key fully, anticlockwise to the unlock position then back to the central position. This should be done the amount of times as the third digit of the EKA Code. 7. Enter the fourth digit - Turn the key fully, clockwise to the lock position again then back to the central position. This should be done the amount of times as the fourth digit of the EKA Code. 8. Once this has been completed turn the key to the unlock position then back to the central position once. If the code has been entered correctly, open the door and the red flashing LED light on the dashboard will stop. You will now be able to start the vehicle. 81

84 5AS Program Remote flow chart INFO - PRESS REMOTE CONTROL 'LOCK' BUTTON 8 TIMES IN SUCCESSION THEN WAIT FOR VEHICLE TO BEEP. STAY IN THIS MODE AND REPEAT PROCEDURE FOR ANY OTHER REMOTES CONTROLS (UP TO 4 MAX). PRESS TO CONTINUE OR <ESC> TO EXIT ENTERING PROGRAMMING MODE... PLEASE WAIT! PROGRAMMING NOW!!! (PRESS EACH REMOTE 8 TIMES etc). PRESS WHEN COMPLETE. SAVING DATA... PLEASE WAIT! PROGRAMMING COMPLETE! 82

85 Pektron Program Remote flow chart INITIALISING ONLY EXISTING WORKING PLIPS OR NEW PLIPS WITH A 20 DIGIT CODE CAN BE PROGRAMMED (REMOVE FIRST AND LAST DIGIT OF BARCODE). PLEASE WRITE DOWN THE FOLLOWING EKA CODE TURN KEY TO POSITION FOR THE FOLLOWING UNLOCK?, LOCK?, UNLOCK?, LOCK?. ARE YOU SURE YOU WANT TO CONTINUE? 1) NO 2) YES Select No if you only require the EKA code and do not want to code a remote PRESS 'LOCK' BUTTON ON EXISTING PLIPS UNTIL VEHICLE BEEPS, REPEAT FOR EACH EXISTING PLIP. PRESS TO CONTINUE OR <ESC> TO EXIT ENTER NUMBER OF NEW PLIPS: 1 Repeat for all new fobs ENTER PLIP BARCODE ********************* PROGRAMMING COMPLETE! 83

86 Immobiliser matching flow chart 5AS Immobiliser fitted to Mems 2J & Mems 3 Engine systems. INITIALISING MATCHING IMMOBILISER TO ENGINE ECU... FAILED TO MATCH IMMOBILISER TOO ENGINE ECU. IMMOBILISER MATCHED TO ENGINE ECU. 84

87 KeyFob Programming Procedure (Remote) Re-initialising Procedure Note. If battery is replaced inside key fob or if key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative, carry out the following reinitialising procedure. Manually Unlock the vehicle using the key Ensure all of the doors, Bonnet and Boot are all closed and both front doors are unlocked. Hold the remote key fob close to the vehicle Press the Padlock or Dimpled button on the key fob button 4 times or more in quick succession, until the vehicle locks are enabled. Typical 2-button key fobs Key fob is re-initialised. Repeat above procedure for all remaining key fobs Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. 3AS Manual Coding Manual procedure for Programming 3AS Plips * The system must be disabled, Switch ignition on the off within 3 seconds * Open the boot and leave it open * Switch ignition on the off within 3 seconds * The Horn Should beep and Alarm LED should come on it indicate that you have entered programming mode * Press the button on Each Plip you wish to program, the Alarm LED should flash to indicate a success for each plip. * Once all Plips have been programmed switch The Ignition on to complete this process 85

88 SAAB Introduction No security pin is required; However a Programmed key is required to start the programming process. Remotes are Programmed Diagnostically.. Note. All keys need to be present; any key not present will be erased from the system. 86

89 SAAB Software flow chart NOTE ENSURE ALL KEYS ARE PRESENT, ANY KEY NOT PRESENT WILL BE DISABLED. ENTER NUMBER OF KEYS TO PROGRAM: 2 INSERT A PROGRAMMED KEY INTO THE IGNITION PROGRAMMING KEY Fail KEY CODING FAILED Loop for Number of keys DOES THIS KEY HAVE A REMOTE? NO YES PRESS THE UNLOCK BUTTON ON THE REMOTE ONCE PER SECOND. 10 TIMES Fasten Seatbelt Light Will Flash once to show success. REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON PROGRAMMING COMPLETE! 87

90 Subaru Introduction There are 2 different systems fitted to these vehicles. In general Immobiliser 1 systems are fitted to vehicles that are older than Model Year 2000 and immobiliser 2 fitted to post 2000 vehicles. 88

91 Subaru Software flow chart ENTER NUMBER OF KEYS TO PROGRAM: 2 SWITCH IGNITION OFF SWITCH IGNITION ON THEN PRESS INITIALISING [ ] ERASING KEY [ ] REMOVE CURRENT KEY. INSERT NEXT KEY AND SWITCH IGNITION ON PROGRAMMING KEY [ ] PROGRAMMING KEY [ ] KEY PROGRAMMED SUCCESSFULLY KEY PROGRAMMED SUCCESSFULLY 89

92 KeyFob Programming Procedure (Remote) Impreza 01 on Forester Legacy Legacy Outback 00 on Programming Procedure Note. If key fob buttons are operated repeatedly whilst vehicle is out of range and central locking / alarm system becomes inoperative or a replacement key fob is obtained. The following programming procedure is required to be carried out before the key fob will operate correctly. If using the following manual key programming procedure: all the existing key fobs must be present, as the manual programming procedure will overwrite the existing key fobs, and make them inoperatable for the vehicle. Remove driver s side kick trim panel Connect central locking registration harness plug (white) connectors together (black wire and black/blue wires) Manually Unlock the vehicle using the key Press the Unlock button and then the Lock on the key fob The vehicle should Unlock and Lock as the key fob buttons are pressed to confirm programming of key fob Repeat above procedure to re-program any remaining key fobs. After the last key fob has been programmed, disconnect the central locking registration harness plug (white) connectors together (black wire and black/blue wires), and refit driver s side kick trim panel Confirm operation of key fobs by locking and unlocking vehicle using key fob buttons. Note. A maximum of 3 key fobs can be programmed to the vehicle. 90

93 Suzuki Introduction There are 2 different systems fitted to these vehicles. No security code as required for these systems Note. Not all keys need to be present, as programming a key is adding that key to the system. The removal of all of the keys is a separate function in the ikeys software menu. 91

94 Program Keys Software flow chart DOES THE KEY HAVE A VIRGIN TRANSPONDER? YES NO SWITCH IGNITION OFF UNABLE TO OBTAIN SECURITY ACCESS. SWITCH IGNITION ON KEY PROGRAMMED SUCCESSFULLY 92

95 Key Fob Programming Procedure (Remote) Remote programming is a manual process for all vehicles supported. Please follow the procedures set out below to ensure accurate programming of the remotes. Ensure Ignition is switch OFF and all Doors are closed. Open Driver s Door, Switch Ignition ON. Within 10 Seconds Switch Ignition OFF and remove the Key from the Ignition Within 20 Seconds - Press Drivers door contact switch 3 times Within 10 Seconds - switch Ignition ON then OFF, Remove the Key from the Ignition Within 10 Seconds - Press the unlock button. Lock Lock 93

96 Toyota / Lexus Introduction The Toyota immobiliser system works with a Master key which is required to gain access to the immobiliser system. Therefore no security code is required. If the Master key is lost then the immobiliser system ECM will need to be replaced / recoded by the Toyota main Dealer. The immobiliser system is also time critical, the instructions must be carried out within the specified time. The handset will display a failure message if this time is exceeded. Note. Not all keys need to be present, as programming a key is adding that key to the system. The removal of all of the keys is a separate function in the ikeys software menu. 94

97 Program Keys Software flow chart SWITCH IGNITION OFF AND REMOVE KEY FROM IGNITION. INITIALISING PLEASE WAIT Fail INSERT BLACK MASTER KEY, SWITCH IGNITION ON. PRESS 120 SECONDS REMAIN. If time limit exceeded THE KEY IN THE IGNITION IS NOT RECOGNISED AS A MASTER KEY. REMOVE MASTER KEY FROM IGNITION. PRESS REGISTRATION FAILURE. TIME EXCEEDED. If time limit exceeded INSERT NEW KEY WITH IGNITION OFF PROGRAMMING KEY PLEASE WAIT Fail KEY CODING FAILED KEY PROGRAMMED SUCCESSFULLY 95

98 Erase Key Software flow chart SWITCH IGNITION OFF AND REMOVE KEY FROM IGNITION. INITIALISING PLEASE WAIT Fail INSERT BLACK MASTER KEY, SWITCH IGNITION ON. PRESS 120 SECONDS REMAIN. If time limit exceeded REGISTRATION FAILURE. THE KEY IN THE IGNITION IS NOT RECOGNISED AS A MASTER KEY. REMOVE MASTER KEY FROM IGNITION. PRESS If time limit exceeded TIME EXCEEDED. Fail ALL SLAVE TRANSPONDERS ERASED UNABLE TO ERASE TRANSPONER(S). 96

99 Key Fob Programming Procedure (Remote) Remote programming is a manual process for all vehicles supported. Please follow the procedures set out below to ensure accurate programming of the remotes. Please ensure the following has been carried out before starting: All Doors are closed Start the vehicle and then stop the vehicle. Remove key from the ignition switch. Open the Drivers door and ensure it is unlocked. Insert key in the ignition for 2 seconds and then remove. Within 40 seconds: Close the driver s door for 2 seconds and then open. Wait 2 seconds: Close the driver s door for 2 seconds and then open Insert key in the ignition for 2 seconds and then remove. Within 40 seconds: Close the driver s door for 2 seconds and then open Wait 2 seconds: Close the driver s door for 2 seconds and then open Close Drivers Door. To Program an additional remote whilst retaining all other remotes programmed. Insert Key in the ignition switch and wait 2 seconds Switch ignition on for 2 seconds and then turn off. Remove key System should lock and unlock once. Note: Please start the following procedure within the next 20 seconds. For Vehicle manufactured in Japan: Simultaneously hold the LOCK and UNLOCK buttons on the remote for seconds and then release. For Vehicles not manufactured Japan: Press the LOCK button on the remote for a minimum of 1 second and then release. Within 3 seconds press the lock button for 1 second and then release. System should lock and unlock once. To Program an additional remote and remove all other remotes programmed. Insert Key in the ignition switch and wait 2 seconds Switch ignition on for 2 seconds and then turn off. Switch ignition on for 2 seconds and then turn off. Remove key System should lock and unlock twice. Note: Please start the following procedure within the next 20 seconds. For Vehicles manufactured in Japan: Simultaneously hold the LOCK and UNLOCK buttons on the remote for seconds and then release. For Vehicles not manufactured in Japan: Press the LOCK button on the remote for a minimum of 1 second and then release. Within 3 seconds press the lock button for 1 second and then release. System should lock and unlock once. If system locks and unlocks twice then the procedure has not been completed. To Exit Programming mode open driver s door. 97

100 Applications List 98

101

102 ALFA ROMEO KEYCODING KEYS 147 All Variants P/D All All CAN Immobiliser SD All Variants P/D All All CAN Immobiliser SD20.1 BRERA All Variants P/D All All CAN Immobiliser SD20.1 GT All Variants P/D All All CAN Immobiliser SD20.1 MINI SUPP SD24.0 Audi KEYCODING KEYS A2 P/D All Immo SD16.3 A2 P/D All Immo SD16.3 A3 P/D All CAN Keys SD16.3 A3 P/D All CAN Remote SD16.3 A3 P/D All Immo SD16.3 A3 P/D All Immo SD16.3 A4 P/D All Immo SD16.3 A4 P/D All Immo SD16.3 A6 P/D All Immo SD16.3 A6 P/D All Immo SD16.3 A8 P/D All Immo SD16.3 A8 P/D All Immo SD16.3 Q7 P/D 07- CAN Keys SD16.3 Q7 P/D 07- CAN Remote SD16.3 S3 P/D All CAN Keys SD16.3 S3 P/D All CAN Remote SD16.3 S3 P/D All Immo SD16.3 S3 P/D All Immo SD16.3 S4 P/D All Immo SD16.3 S4 P/D All Immo SD16.3 TT P/D All Immo SD16.3 TT P/D All Immo SD16.3 Audi PIN EXTRACTION A2 P/D All MOTOMETER DASH SD16.3 A2 P/D All VDO DASH SD24.0 A2 P/D All EMS SD16.3 A3 P/D All MOTOMETER DASH SD16.3 A3 P/D All VDO DASH SD24.0 A3 P/D All EMS SD16.3 A4 P/D All MOTOMETER DASH SD16.3 A4 P/D All VDO DASH SD24.0 A4 P/D All EMS SD16.3 A6 P/D All MOTOMETER DASH SD16.3 A6 P/D All VDO DASH SD24.0 A6 P/D All EMS SD16.3 A8 P/D All MOTOMETER DASH SD16.3 A8 P/D All VDO DASH SD24.0 A8 P/D All EMS SD16.3 S3 P/D All MOTOMETER DASH SD16.3 S3 P/D All VDO DASH SD24.0 S3 P/D All EMS SD16.3 S4 P/D All MOTOMETER DASH SD16.3 S4 P/D All VDO DASH SD24.0 S4 P/D All EMS SD16.3 TT P/D All MOTOMETER DASH SD16.3 TT P/D All VDO DASH SD24.0 TT P/D All EMS SD16.3 Citroen KEYCODING KEYS BERLINGO P/D All BSI SD18.0 BERLINGO P/D All BSI SD18.0 BERLINGO P/D All Immo SD16.3 BERLINGO P/D All CPH SD21.1 C2 P/D All BSI SD16.3 C3 P/D All CAN BSI SD16.3 C3 P/D All BSI SD18.0 C4 P/D All CAN BSI SD18.0 C5 P/D All CAN BSI SD18.0 C5 P/D All BSI SD18.0 C8 P/D All BSI SD16.3 DISPATCH P/D All Immo SD16.3 DISPATCH P/D All CPH SD21.1 EVASION P/D All CPH SD21.1 SAXO P/D All Immo SD16.3 SYNERGIE P/D All CPH SD21.1 XANTIA P/D All Immo SD16.3 XANTIA P/D All CPH SD21.1 XSARA P/D All BSI SD18.0 XSARA P/D All BSI SD18.0 XSARA P/D All BSI SD18.0 XSARA P/D All CPH SD21.1 XSARA PICASSO P/D All BSI SD16.3 XSARA PICASSO P/D All BSI SD16.3 Daewoo KEYCODING KEYS KALOS P/D All Immobiliser SD16.3 LACETTI P/D All Immobiliser SD16.3 LANOS P/D All Immobiliser SD16.3 MATIZ P/D All ECU Matching SD16.3 MATIZ P/D All Immobiliser SD16.3 NUBIRA III P/D All Immobiliser SD16.3 TACUMA P/D All Immobiliser SD16.3 FIAT KEYCODING KEYS BRAVO All Variants P/D All All CAN Immobiliser SD20.1 CROMA All Variants P/D All All CAN Immobiliser SD20.1 DOBLO All Variants P/D All All CAN Immobiliser SD20.1 DUCATO All Variants P/D All All CAN Immobiliser SD20.1 IDEA All Variants P/D All All CAN Immobiliser SD20.1 LINEA All Variants P/D All All CAN Immobiliser SD20.1 PALIO RST All Variants P/D All All CAN Immobiliser SD20.1

103 MINI SUPP SD24.0 FIAT KEYCODING KEYS PANDA All Variants P/D All All CAN Immobiliser SD20.1 PERLA All Variants P/D All All CAN Immobiliser SD20.1 PUNTO All Variants P/D All All CAN Immobiliser SD20.1 PUNTO All Variants P/D All All CAN Immobiliser SD20.1 PUNTO LA All Variants P/D All All CAN Immobiliser SD20.1 SEDICI All Variants P/D All All CAN Immobiliser SD20.1 STILO All Variants P/D All All CAN Immobiliser SD20.1 Ford KEYCODING KEYS COUGAR P All PATS SD18.0 COURIER P All PATS SD18.0 COURIER D All PATS SD18.0 COURIER P All PATS 1 COURIER SD16.3 COURIER D All PATS 1 COURIER SD16.3 ESCORT P All PATS 2 PETROL SD16.3 ESCORT P All PATS 1 ESCORT SD16.3 ESCORT D All PATS 2 DIESEL SD16.3 ESCORT D All PATS 1 ESCORT SD16.3 FIESTA P All PATS SD18.0 FIESTA D All PATS SD18.0 FIESTA P All PATS 2 PETROL SD16.3 FIESTA D All PATS SD16.3 FIESTA D All PATS 2 DIESEL SD16.3 FIESTA P All PATS SD16.3 FIESTA P All PATS 3 CAN SD22.3 FIESTA D All PATS 3 CAN SD22.3 FIESTA P All PATS CAN IPC SD23.1 FIESTA D All PATS CAN IPC SD23.1 FOCUS P All PATS SD18.0 FOCUS D All PATS SD18.0 FOCUS P All PATS CAN IC SD23.0 FOCUS D All PATS CAN IC SD23.0 FUSION P All PATS 3 CAN SD22.3 FUSION D All PATS 3 CAN SD22.3 GALAXY P All PATS 3 SCP SD16.3 GALAXY P All PATS SD16.3 GALAXY D All PATS SD16.3 GALAXY P All VAG Timed Access SD16.3 GALAXY D All VAG Timed Access SD16.3 GALAXY D All PATS 3 SCP SD16.3 GALAXY P All PATS CAN BCMii SD23.2 GALAXY D All PATS CAN BCMii SD23.2 KA P PATS SD18.0 KA P PATS SD18.0 KA P PATS 2 PETROL SD16.3 KA P PATS 3 CAN SD22.4 MONDEO P All PATS SD16.3 MONDEO P All PATS 2 PETROL SD16.3 MONDEO D All PATS 2 DIESEL SD16.3 MONDEO P All PATS SD18.0 MONDEO D All PATS SD18.0 ORION P All PATS SD16.3 ORION D All PATS SD16.3 PUMA P All PATS SD18.0 SCORPIO Petrol V6/12V P All PATS SD16.3 SCORPIO D All PATS SD16.3 S-MAX P All PATS CAN BCMii SD23.2 S-MAX D All PATS CAN BCMii SD23.2 TRANSIT P All PATS SD18.0 TRANSIT D All PATS SD18.0 TRANSIT P All PATS SD18.0 TRANSIT D All PATS SD18.0 GM-Opel KEYCODING KEYS AGILA P/D All Immo SD16.3 AGILA P/D All Remote SD16.3 ARENA P/D All Immo SD16.3 ARENA P/D All Remote SD16.3 ASTRA-F P/D All Immo SD16.3 ASTRA-F P/D All Remote SD16.3 ASTRA-G P/D All Immo SD16.3 ASTRA-G P/D All Remote SD16.3 ASTRA-H P/D All Immo3 (CAN) SD16.3 CALIBRA P/D All Immo SD16.3 CALIBRA P/D All Remote SD16.3 CAVALIER P/D All Immo SD16.3 CAVALIER P/D All Remote SD16.3 CORSA-B P/D All Immo SD16.3 CORSA-B P/D All Remote SD16.3 CORSA-C P/D All Immo SD16.3 CORSA-C P/D All Remote SD16.3 CORSA-C COMBO P/D All Immo SD16.3 CORSA-C COMBO P/D All Remote SD16.3 CORSA-D P/D All Immo 4 (CAN) SD21.2 FRONTERA-A P/D All -98 Immo SD16.3 FRONTERA-A P/D All -98 Remote SD16.3 FRONTERA-B P/D All 98- Immo SD16.3 FRONTERA-B P/D All 98- Remote SD16.3 MERIVA P/D All Immo SD16.3 MERIVA P/D All Remote SD16.3 MONTEREY P/D All Immo SD16.3 MONTEREY P/D All 98- Immo SD16.3 MONTEREY P/D All Remote SD16.3 OMEGA-B P/D All Immo SD16.3 OMEGA-B P/D All Immo SD16.3 OMEGA-B P/D All Remote SD16.3 TIGRA P/D All Immo SD16.3 TIGRA P/D All Remote SD16.3

104 GM-Opel KEYCODING KEYS VECTRA-B P/D All Immo SD16.3 VECTRA-B P/D All Remote SD16.3 VECTRA-B P/D All Immo SD16.3 VECTRA-B P/D All Remote SD16.3 VECTRA-C P/D All Immo3 (CAN) SD16.3 VX220 P/D All Immo SD16.3 VX220 P/D All Remote SD16.3 ZAFIRA P/D All Immo SD16.3 ZAFIRA P/D All Remote SD16.3 ZAFIRA-B P/D All Immo3 (CAN) SD16.3 MINI SUPP SD24.0 Honda KEYCODING KEYS ACCORD P/D All Immobiliser SD16.3 CIVIC P/D All Immobiliser SD18.0 CR-V P/D All Immobiliser SD16.3 HR-V P/D All Immobiliser SD16.3 JAZZ P/D All Immobiliser SD18.0 S2000 P/D All Immobiliser SD16.3 LANCIA KEYCODING KEYS MUSA All Variants P/D All All CAN Immobiliser SD20.1 THESIS All Variants P/D All All CAN Immobiliser SD20.1 YPSILON All Variants P/D All All CAN Immobiliser SD20.1 LandRover KEYCODING KEYS DISCOVERY III P/D All Immobiliser SD16.3 FREELANDER P/D All CCU SD19.3 RANGE ROVER SPORT P/D All Immobiliser SD16.3 Lexus KEYCODING KEYS IS200 P/D All Immobiliser SD16.3 IS300 P/D All Immobiliser SD16.3 Mitsubishi KEYCODING KEYS 3000 GT P/D All Immobiliser SD16.3 CARISMA P/D All Immobiliser SD16.3 COLT P/D All Immobiliser SD16.3 COLT P/D All Immobiliser SD21.0 EVO P/D All Immobiliser SD16.3 GALANT P/D All Immobiliser SD16.3 GALANT P/D All 04 - Immobiliser SD16.3 GALANT P/D All Immobiliser SD16.3 GALANT P/D All Immobiliser SD16.3 GALANT WAGON P/D All Immobiliser SD16.3 L200 P/D All Immobiliser SD16.3 L200 P/D All Immobiliser SD16.3 L400 P/D All Immobiliser SD16.3 LANCER P/D All Immobiliser SD16.3 LANCER P/D All Immobiliser SD16.3 LANCER WAGON P/D All Immobiliser SD16.3 OUTLANDER P/D All Immobiliser SD16.3 PININ P/D All Immobiliser SD16.3 SHOGUN P/D All Immobiliser SD16.3 SHOGUN P/D All Immobiliser SD16.3 SHOGUN SPORT P/D All Immobiliser SD16.3 SIGMA P/D All Immobiliser SD16.3 SPACESTAR P/D All Immobiliser SD16.3 SPACEWAGON P/D All Immobiliser SD16.3 SPACEWAGON P/D All Immobiliser SD16.3 Nissan KEYCODING KEYS ALMERA P/D All NATS SD16.3 MAXIMA P/D All NATS SD16.3 MICRA P/D All NATS SD16.3 PRIMERA P/D All NATS SD16.3 SKYLINE P/D All NATS SD16.3 TERRANO II P/D All NATS SD16.3 X-TRAIL P/D All NATS SD16.3 Peugeot KEYCODING KEYS 106 P/D All Immo SD P/D All Immo SD P/D All BSI SD P/D All Immo SD P/D All Old Bsi SD P/D All CAN BSI SD P/D All Immo SD P/D All CAN BSI SD P/D All BSI SD P/D All CPH SD P/D All BSI SD P/D All BSI SD P/D All BSI SD P/D All BSI SD P/D All CAN BSI SD P/D All Immo SD P/D All Immo SD P/D All CPH SD P/D All BSI SD18.0 EXPERT P/D All CPH SD21.1 PARTNER P/D All BSI SD18.0 PARTNER P/D All BSI SD18.0 PARTNER P/D All CPH SD21.1 Renault KEYCODING KEYS CLIO P/D All Immobiliser SD16.3 CLIO II P/D All Immobiliser SD16.3 CLIO II PH2 P/D All Immobiliser SD16.3

105 MINI SUPP SD24.0 Renault KEYCODING KEYS ESPACE P/D All Immobiliser SD16.3 KANGOO P/D All type SD16.3 KANGOO II P/D All Immobiliser SD16.3 LAGUNA I P/D All Immobiliser SD16.3 LAGUNA II P/D All Immobiliser SD16.3 MASTER 1 P/D All 01- Immo SD16.3 MASTER II P/D All Immobiliser SD16.3 MEGANE P/D All Immo SD16.3 SCENIC P/D All Immo SD16.3 TRAFIC II P/D All Immobiliser SD16.3 Rover-MG IMMOBILISER MATCH 100 SERIES 111 P K2D Mems 1.6 MPi Turbo SD SERIES 111 P K2D Mems 1.6 SPi CAT SD SERIES 111 P K2D Mems 1.6 SPi NON-CAT SD SERIES 111 P K2D Mems 1.6 STAND.Mpi SD SERIES 111 P K8-1.1 Mems SD SERIES 114 P K Mems 1.6 MPi Turbo SD SERIES 114 P K2A Mems 1.6 MPi Turbo SD SERIES 114 P K8-1.4 Mems 1.6 MPi Turbo SD SERIES 114 P K Mems 1.6 SPi CAT SD SERIES 114 P K2A Mems 1.6 SPi CAT SD SERIES 114 P K8-1.4 Mems 1.6 SPi CAT SD SERIES 114 P K Mems 1.6 SPi NON-CAT SD SERIES 114 P K2A Mems 1.6 SPi NON-CAT SD SERIES 114 P K8-1.4 Mems 1.6 SPi NON-CAT SD SERIES 114 P K Mems 1.6 STAND.Mpi SD SERIES 114 P K2A Mems 1.6 STAND.Mpi SD SERIES 114 P K8-1.4 Mems 1.6 STAND.Mpi SD SERIES 114 P K4C/D Mems 1.6 MPi Turbo SD SERIES 114 P K Mems 1.6 MPi Turbo SD SERIES 114 P K4F Mems 1.6 MPi Turbo SD SERIES 114 P K4C/D Mems 1.6 SPi CAT SD SERIES 114 P K Mems 1.6 SPi CAT SD SERIES 114 P K4F Mems 1.6 SPi CAT SD SERIES 114 P K4C/D Mems 1.6 SPi NON-CAT SD SERIES 114 P K Mems 1.6 SPi NON-CAT SD SERIES 114 P K4F Mems 1.6 SPi NON-CAT SD SERIES 114 P K4C/D Mems 1.6 STAND.Mpi SD SERIES 114 P K Mems 1.6 STAND.Mpi SD SERIES 114 P K4F Mems 1.6 STAND.Mpi SD SERIES 114 P K8-1.4 Mems SD SERIES 200 vi P/D All Mems 2J CD1 200 SERIES 214 P K Mems 1.6 MPi Turbo SD SERIES 214 P K Mems 1.6 MPi Turbo SD SERIES 214 P K4F Mems 1.6 MPi Turbo SD SERIES 214 P K Mems 1.6 SPi CAT SD SERIES 214 P K4F Mems 1.6 SPi CAT SD SERIES 214 P K Mems 1.6 SPi NON-CAT SD SERIES 214 P K4F Mems 1.6 SPi NON-CAT SD SERIES 214 P K Mems 1.6 STAND.Mpi SD SERIES 214 P K4F Mems 1.6 STAND.Mpi SD SERIES 214 P KC/D Mems 1.6 MPi Turbo SD SERIES 214 P KC/D Mems 1.6 SPi CAT SD SERIES 214 P KC/D Mems 1.6 SPi NON-CAT SD SERIES 214 P KC/D Mems 1.6 STAND.Mpi SD SERIES 214 P K16 Mems SD SERIES 214 P K8 Mems SD SERIES 216 P K16 Mems SD SERIES 218 P K16 Mems SD SERIES 218 Coupe P/D All Mems 2J CD1 200 SERIES 220 Coupe P T4 Mems 1.6 MONT.MPi SD SERIES 220 Coupe P T4 Mems 1.6 MPi Turbo SD SERIES 220 Coupe P T4 Mems 1.6 SPi CAT SD SERIES 220 Coupe P T4 Mems 1.6 SPi NON-CAT SD SERIES 220 Coupe P T4 Mems 1.6 STAND.Mpi SD SERIES 220 GTI P M4 Mems 1.6 MONT.MPi SD SERIES 220 GTI P M4 Mems 1.6 MPi Turbo SD SERIES 220 GTI P M4 Mems 1.6 SPi CAT SD SERIES 220 GTI P M4 Mems 1.6 SPi NON-CAT SD SERIES 220 GTI P M4 Mems 1.6 STAND.Mpi SD SERIES 220 Turbo/Coupe P T4 Mems 1.6 MONT.MPi SD SERIES 220 Turbo/Coupe P T4 Mems 1.6 MPi Turbo SD SERIES 1.1L P K8-1.1 Mems SD SERIES vvc P/D All Mems CD1 25 SERIES P/D Mems CD1 25 SERIES P/D Mems CD1 25 SERIES P/D Mems CD1 25 SERIES P/D Mems CD1 400 SERIES 414 P K Mems 1.6 MPi Turbo SD SERIES 414 P K4F Mems 1.6 MPi Turbo SD SERIES 414 P K Mems 1.6 SPi CAT SD SERIES 414 P K4F Mems 1.6 SPi CAT SD SERIES 414 P K Mems 1.6 SPi NON-CAT SD SERIES 414 P K4F Mems 1.6 SPi NON-CAT SD SERIES 414 P K Mems 1.6 STAND.Mpi SD SERIES 414 P K4F Mems 1.6 STAND.Mpi SD SERIES 414 P KC/D Mems 1.6 MPi Turbo SD SERIES 414 P K Mems 1.6 MPi Turbo SD SERIES 414 P KC/D Mems 1.6 SPi CAT SD SERIES 414 P K Mems 1.6 SPi CAT SD SERIES 414 P KC/D Mems 1.6 SPi NON-CAT SD SERIES 414 P K Mems 1.6 SPi NON-CAT SD SERIES 414 P KC/D Mems 1.6 STAND.Mpi SD SERIES 414 P K Mems 1.6 STAND.Mpi SD SERIES 414 P K Mems SD SERIES 416 P K Mems SD SERIES 416 Tourer P K16 Mems SD21.3

106 Rover-MG IMMOBILISER MATCH 400 SERIES 420 P T4 Mems SD SERIES 420 GTI P M4 Mems 1.6 MONT.MPi SD SERIES 420 GTI P M4 Mems 1.6 MPi Turbo SD SERIES 420 GTI P M4 Mems 1.6 SPi CAT SD SERIES 420 GTI P M4 Mems 1.6 SPi NON-CAT SD SERIES 420 GTI P M4 Mems 1.6 STAND.Mpi SD SERIES 420 Touring P T4 Mems 1.6 MONT.MPi SD SERIES 420 Touring P T4 Mems 1.6 MPi Turbo SD SERIES 420 Touring P T4 Mems 1.6 SPi CAT SD SERIES 420 Touring P T4 Mems 1.6 SPi NON-CAT SD SERIES 420 Touring P T4 Mems 1.6 STAND.Mpi SD SERIES P/D Mems CD1 45 SERIES P/D Mems CD1 45 SERIES P/D Mems CD1 600 SERIES 620 Turbo P T4 Mems SD SERIES 820 P T4 Mems 1.6 MONT.MPi SD SERIES 820 P T4 Mems 1.6 MPi Turbo SD SERIES 820 P T4 Mems 1.6 SPi CAT SD SERIES 820 P T4 Mems 1.6 SPi NON-CAT SD SERIES 820 P T4 Mems 1.6 STAND.Mpi SD SERIES 820 P T4 Mems SD SERIES 820 Vitesse P T4 Mems 1.6 MPi Turbo SD SERIES 820 Vitesse P T4 Mems 1.6 SPi CAT SD SERIES 820 Vitesse P T4 Mems 1.6 SPi NON-CAT SD SERIES 820 Vitesse P T4 Mems 1.6 STAND.Mpi SD SERIES 820 Vitesse P T4 Mems 1.6 MONT.MPi SD SERIES 820 Vitesse Sport P T4 Mems 1.6 MONT.MPi SD SERIES 820 Vitesse Sport P T4 Mems 1.6 MPi Turbo SD SERIES 820 Vitesse Sport P T4 Mems 1.6 SPi CAT SD SERIES 820 Vitesse Sport P T4 Mems 1.6 SPi NON-CAT SD SERIES 820 Vitesse Sport P T4 Mems 1.6 STAND.Mpi SD SERIES 820 Vitesse Sport P T4 Mems SD SERIES 825 P/D All Mems 2J CD1 METRO 1.1L P K2D Mems 1.6 MPi Turbo SD21.3 METRO 1.1L P K2D Mems 1.6 SPi CAT SD21.3 METRO 1.1L P K2D Mems 1.6 SPi NON-CAT SD21.3 METRO 1.1L P K2D Mems 1.6 STAND.Mpi SD21.3 METRO 1.4L P K4C/D Mems 1.6 MPi Turbo SD21.3 METRO 1.4L P K Mems 1.6 MPi Turbo SD21.3 METRO 1.4L P K2A Mems 1.6 MPi Turbo SD21.3 METRO 1.4L P K4C/D Mems 1.6 SPi CAT SD21.3 METRO 1.4L P K Mems 1.6 SPi CAT SD21.3 METRO 1.4L P K2A Mems 1.6 SPi CAT SD21.3 METRO 1.4L P K4C/D Mems 1.6 SPi NON-CAT SD21.3 METRO 1.4L P K Mems 1.6 SPi NON-CAT SD21.3 METRO 1.4L P K2A Mems 1.6 SPi NON-CAT SD21.3 METRO 1.4L P K4C/D Mems 1.6 STAND.Mpi SD21.3 METRO 1.4L P K Mems 1.6 STAND.Mpi SD21.3 METRO 1.4L P K2A Mems 1.6 STAND.Mpi SD21.3 METRO 1.4L P K Mems 1.6 MPi Turbo SD21.3 METRO 1.4L P K4F Mems 1.6 MPi Turbo SD21.3 METRO 1.4L P K Mems 1.6 SPi CAT SD21.3 METRO 1.4L P K4F Mems 1.6 SPi CAT SD21.3 METRO 1.4L P K Mems 1.6 SPi NON-CAT SD21.3 METRO 1.4L P K4F Mems 1.6 SPi NON-CAT SD21.3 METRO 1.4L P K Mems 1.6 STAND.Mpi SD21.3 METRO 1.4L P K4F Mems 1.6 STAND.Mpi SD21.3 MG-F 1.6L P K16 Mems SD21.3 MG-F 1.8L P K Mems SD21.3 MG-F P/D Mems CD1 MG-F P/D Mems CD1 MINI 1.3L P Mems 1.6 SPi NON-CAT SD21.3 MINI 1.3L P Mems 1.6 SPi CAT SD21.3 MINI 1.3L P Mems 1.6 STAND.Mpi SD21.3 TF P/D Mems CD1 ZR P/D Mems CD1 ZS P/D Mems CD1 ZS P/D All Mems CD1 MINI SUPP SD24.0 Rover-MG KEYCODING KEYS 100 SERIES P/D All AS SD SERIES P/D All EKA SD SERIES P/D All AS SD SERIES P/D All EKA SD SERIES P/D All EKA SD SERIES P/D All AS SD SERIES P/D All EKA SD SERIES P/D All Pektron SD SERIES P/D All AS SD SERIES P/D All EKA SD SERIES P/D All EKA SD SERIES P/D All AS SD SERIES P/D All EKA SD SERIES P/D All Pektron SD SERIES P/D All EKA SD SERIES P/D All EKA SD16.3 METRO P/D All EKA SD16.3 MG-F P/D All AS SD16.3 MG-F P/D All EKA SD16.3 MINI P/D All AS SD16.3 MINI P/D All EKA SD16.3 ZR P/D All EKA SD16.3 ZR P/D All Pektron SD20.0 ZS P/D All EKA SD16.3 ZS P/D All Pektron SD20.0 SAAB KEYCODING KEYS 93 P/D All All Variants SD16.3

107 MINI SUPP SD24.0 SAAB KEYCODING KEYS 95 P/D All All Variants SD16.3 Seat KEYCODING KEYS ALHAMBRA P/D Immo SD16.3 ALHAMBRA P/D Immo SD16.3 ALTEA P/D CAN Keys SD16.3 ALTEA P/D CAN Remote SD16.3 AROSA P/D Immo SD16.3 AROSA P/D Immo SD16.3 CORDOBA P/D Immo SD16.3 CORDOBA P/D Immo SD16.3 IBIZA P/D Immo SD16.3 IBIZA P/D Immo SD16.3 IBIZA P/D Immo SD16.3 IBIZA P/D Immo SD16.3 LEON (1P) P/D CAN Keys SD16.3 LEON (1P) P/D CAN Remote SD16.3 LEON P/D Immo SD16.3 LEON P/D Immo SD16.3 TOLEDO (5P) P/D CAN Keys SD16.3 TOLEDO (5P) P/D CAN Keys SD16.3 TOLEDO (5P) P/D CAN Keys SD16.3 TOLEDO (5P) P/D CAN Remote SD16.3 TOLEDO (5P) P/D CAN Remote SD16.3 TOLEDO (5P) P/D CAN Remote SD16.3 TOLEDO P/D Immo SD16.3 TOLEDO P/D Immo SD16.3 Seat PIN EXTRACTION ALHAMBRA P/D MOTOMETER DASH SD16.3 ALHAMBRA P/D VDO DASH SD24.0 ALHAMBRA P/D EMS SD16.3 AROSA P/D MOTOMETER DASH SD16.3 AROSA P/D VDO DASH SD24.0 AROSA P/D EMS SD16.3 CORDOBA P/D MOTOMETER DASH SD16.3 CORDOBA P/D VDO DASH SD24.0 CORDOBA P/D EMS SD16.3 IBIZA P/D MOTOMETER DASH SD16.3 IBIZA P/D MOTOMETER DASH SD16.3 IBIZA P/D VDO DASH SD24.0 IBIZA P/D VDO DASH SD24.0 IBIZA P/D EMS SD16.3 IBIZA P/D EMS SD16.3 LEON P/D MOTOMETER DASH SD16.3 LEON P/D VDO DASH SD24.0 LEON P/D EMS SD16.3 TOLEDO P/D MOTOMETER DASH SD16.3 TOLEDO P/D VDO DASH SD24.0 TOLEDO P/D EMS SD16.3 Skoda KEYCODING KEYS FABIA P/D Immo SD16.3 FABIA P/D Immo SD16.3 FELICIA P/D Immo SD16.3 FELICIA P/D Immo SD16.3 OCTAVIA P/D Immo SD16.3 OCTAVIA P/D Immo SD16.3 OCTAVIA II P/D CAN Keys SD16.3 OCTAVIA II P/D CAN Remote SD16.3 Skoda PIN EXTRACTION FABIA P/D MOTOMETER DASH SD16.3 FABIA P/D VDO DASH SD24.0 FABIA P/D EMS SD16.3 FELICIA P/D MOTOMETER DASH SD16.3 FELICIA P/D VDO DASH SD24.0 FELICIA P/D EMS SD16.3 OCTAVIA P/D MOTOMETER DASH SD16.3 OCTAVIA P/D VDO DASH SD24.0 OCTAVIA P/D EMS SD16.3 Subaru KEYCODING KEYS OUTBACK P/D All Immo SD16.3 OUTBACK P/D All 00- Immo SD16.3 Suzuki KEYCODING KEYS BALENO DHW P/D All Immobiliser SD16.3 WAGON R P/D All Immobiliser SD16.3 Toyota KEYCODING KEYS AVENSIS P/D All Auto Detect SD16.3 AVENSIS II P/D All Auto Detect SD16.3 AVENSIS VERSO P/D All Auto Detect SD16.3 COROLLA P/D All Auto Detect SD16.3 COROLLA P/D All Auto Detect SD16.3 COROLLA VERSO P/D All Auto Detect SD16.3 LANDCRUISER AMAZON P/D All Auto Detect SD16.3 LANDCRUISER COLORADO P/D All Auto Detect SD16.3 LANDCRUISER COLORADO P/D All Auto Detect SD16.3 MR2 P/D All Auto Detect SD16.3 PREVIA P/D All Auto Detect SD16.3 RAV4 P/D All Auto Detect SD16.3 YARIS P/D All Auto Detect SD16.3 YARIS VERSO P/D All Auto Detect SD16.3 Volkswagen KEYCODING KEYS BEETLE P/D All Immo SD16.3

108 Volkswagen KEYCODING KEYS BEETLE P/D All Immo SD16.3 BORA P/D Immo SD16.3 BORA P/D Immo SD16.3 CADDY P/D Immo SD16.3 CADDY P/D Immo SD16.3 CORRADO P/D All 95 Immo SD16.3 CORRADO P/D All 95 Immo SD16.3 EOS (1K) P/D CAN Keys SD16.3 EOS (1K) P/D CAN Remote SD16.3 GOLF (1K) P/D CAN Keys SD16.3 GOLF (1K) P/D CAN Remote SD16.3 GOLF P/D Immo SD16.3 GOLF P/D Immo SD16.3 JETTA (1K) P/D CAN Keys SD16.3 JETTA (1K) P/D CAN Remote SD16.3 LUPO P/D Immo SD16.3 LUPO P/D Immo SD16.3 PASSAT (3C) P/D CAN Keys SD16.3 PASSAT (3C) P/D CAN Remote SD16.3 PASSAT P/D Immo SD16.3 PASSAT P/D Immo SD16.3 POLO P/D Immo SD16.3 POLO P/D Immo SD16.3 SHARAN P/D Immo SD16.3 SHARAN P/D Immo SD16.3 TOURAN (1T) P/D CAN Keys SD16.3 TOURAN (1T) P/D CAN Remote SD16.3 VENTO P/D Immo SD16.3 VENTO P/D Immo SD16.3 MINI SUPP SD24.0 Volkswagen PIN EXTRACTION BEETLE P/D All MOTOMETER DASH SD16.3 BEETLE P/D All VDO DASH SD24.0 BEETLE P/D All EMS SD16.3 BORA P/D MOTOMETER DASH SD16.3 BORA P/D VDO DASH SD24.0 BORA P/D EMS SD16.3 CADDY P/D MOTOMETER DASH SD16.3 CADDY P/D VDO DASH SD24.0 CADDY P/D EMS SD16.3 CORRADO P/D All 95 MOTOMETER DASH SD16.3 CORRADO P/D All 95 VDO DASH SD24.0 CORRADO P/D All 95 EMS SD16.3 GOLF P/D MOTOMETER DASH SD16.3 GOLF P/D MOTOMETER DASH SD16.3 GOLF P/D VDO DASH SD24.0 GOLF P/D VDO DASH SD24.0 GOLF P/D EMS SD16.3 GOLF P/D EMS SD16.3 LUPO P/D MOTOMETER DASH SD16.3 LUPO P/D VDO DASH SD24.0 LUPO P/D EMS SD16.3 PASSAT P/D MOTOMETER DASH SD16.3 PASSAT P/D VDO DASH SD24.0 PASSAT P/D EMS SD16.3 POLO P/D MOTOMETER DASH SD16.3 POLO P/D VDO DASH SD24.0 POLO P/D EMS SD16.3 SHARAN P/D MOTOMETER DASH SD16.3 SHARAN P/D VDO DASH SD24.0 SHARAN P/D EMS SD16.3 VENTO P/D MOTOMETER DASH SD16.3 VENTO P/D VDO DASH SD24.0 VENTO P/D EMS SD16.3 Citroen KEYCODING KEYS BERLINGO P/D All Immo SD24.0 DISPATCH P/D All Immo SD24.0 SAXO P/D All Immo SD24.0 XANTIA P/D All Immo SD24.0 Peugeot KEYCODING KEYS 206 P/D All Immo SD P/D All Immo SD24.0

109

110

111

112 PO BOX 3467, Chippenham, Wiltshire, SN15 9FH, UK Sales & Customer Services: + 44 (0) Facsimile: + 44 (0) sales@spdiagnostics.com support@spdiagnostics.com