Points Conversion. Optical Trigger Conversion. Specifications. Applications. Optical Trigger - Installation Kits CRANECAMS.
|
|
- Shana Bond
- 6 years ago
- Views:
Transcription
1 Points Conversion Optical Trigger Conversion Easy to install in less than 1 hour! Converts points-type distributor to precision optically triggered system! No maintenance! Drives HI-6, HI-6S and most aftermarket ignitions with points/module input. Stable timing with precise settings! Eliminates spark scatter for greater energy No more tune-ups due to worn points! Installation kit is required; not included. Now you can use a high output CD ignition on your older points-type vehicle! Optical Trigger Conversion Unit (Installation Kit Required) Trigger output 6 to 18 volts, reverse polarity protected, negative ground only. Not compatible with 6 volt electrical systems. Points/module type (12 volt square wave). Triggers spark on rising edge. 1/4 amp maximum load. Short circuit protected. NOTE: Output cannot directly drive any coil or tach adapter. Optical Trigger - Installation Kits IGNITION Includes shutters and brackets for installation of optical trigger on domestic 4, 6 and 8 cylinder and VW/Bosch 009 breaker point distributor applications Includes shutters and brackets for installation of optical trigger on most import 4, 6 and 8 cylinder breaker point applications. Also used as universal installation kit for many other breaker point applications Includes shutters and brackets for installation of optical trigger on imports with 4 and 6 cylinder engines equipped with certain Bosch, Hitachi, or Nippondenso OE Electronic Ignition Modules. For applications where the OE module has failed and must be eliminated Includes shutters and brackets for installation of optical trigger on British imports with 4, 6, and 8 cylinder engines equipped with Lucas OPUS distributors. For applications where the OPUS module has failed and must be eliminated. Note that the HI-6S is not compatible with 12 cylinder engines Includes shutters and brackets for installation of optical trigger on Mallory YL Dual Point and Unilite 8 cylinder distributor applications CRANECAMS.COM
2 Points Conversion Ignition XR-i Points To Electronic Ignition Easy 2 wire hook-up. Improved fuel mileage. Faster, more reliable engine starts. Industry s 1st and only with rev limiter. Adjustable rev limiter from RPM. Fully digital and maintenance free. Timing picked up from distributor cam lobe. Pinpoint accurate ignition timing. Complete under cap restoration perfect. Never replace or adjust points again! Fully sealed from moisture and dirt. High temperature protection won t leave you stranded! CARB E.O. D state legal. Current draw 6-18 v. reverse polarity protection, negative ground 3 amps 5,500 RPM XR-i Only RPM operating range RPM limiter range 8,000 RPM 4,000 to 8,000 RPM Ford V Chevy V (most) Pontiac V Up Oldsmobile V XR-i & PS20 Coil Kit Ford V Primary voltage output Primary energy output Peak spark gap current Spark duration 400 volts (inductive discharge) 45 millijoules with PS20 coil and 1.65L ballast resistor 50 milliamps with PS20 coil and 1.65L ballast resistor ,000 RPM Chevy V (most) Pontiac V Up Oldsmobile V A. Recommended Coils A. PS20, Black, Canister Style B. PS40, Chrome, Canister Style B FAX 403
3 IGNITION Points Conversion Ignitions XR700 Points-To-Electronic Ignition Converts points type distributors to electronic ignition! Increased timing accuracy. Replaces many Bosch, Lucas, Hitachi and ND units. All new status LED light for easy diagnostics. Fully potted for protection from dirt, moisture and vibration. Optical trigger for precise ignition timing! More powerful signal than points type Most reliable of its type 6th generation of reliability Short circuit proof Positive ground compatible 50 State Legal XR700 System For Domestic 4, 6 and 8 Cylinder and VW/Bosch 009 Distributor. 12 Volt Negative or Positive Ground. For 1975 and earlier vehicles. CARB E.O. D For Import and Universal 4, 6 and 8 Cylinder. 12 Volt Negative or Positive Ground. For 1975 and earlier vehicles. CARB E.O. D For Imports with 4 and 6 cylinder engines equipped with Bosch, Hitachi, or Nippondenso OE Electronic Ignition Modules. For applications where the OE module has failed and must be eliminated. See applications chart for details. CARB E.O. D For British imports with 4, 6 and 8 cylinder engines equipped with Lucas OPUS distributors. For applications where the OPUS module has failed and must be eliminated. OPUS system has three wires on OE pickup. If pickup has two wires, you have a conventional magnetic pickup distributor and cannot install an optical trigger. You must use an HI-6R (Pt. No ) connected directly to the magnetic pickup in the Lucas distributor. CARB E.O. D For Mallory YL Dual Point and Unilite Distributor applications only. For 1975 and earlier vehicles. CARB E.O. D to 18 volts, reverse polarity protected, negative or positive ground. Not compatible with 6 volt electrical systems as these may drop below 4 volts during cranking. Coil current limit 4.5 amps (externally limited by ballast resistor on XR700). Internal short circuit protection limit set at 7 amps. RPM range 6,000 RPM (RPM range higher for 4 and 6 cylinder engines). Primary voltage output 400 volts (inductive discharge) Primary energy output 60 millijoules with PS20/40 coil. Peak spark gap current 60 milliamps with PS20/40 coil. Spark duration 300 microseconds at 6,000 RPM Dimensions 3-1/2 L x 3 W x 1-1/2 H, 1 lb. Recommended Coils PS20, Black, Canister Style PS40, Chrome, Canister Style CRANECAMS.COM
4 Points Conversion Ignition XR700 Replacement Parts And Optional Accessories A. XR700 Ignition Module For 12 Volt Negative or Positive Ground (does not include optical trigger or required installation kit) B. Optical Trigger For XR700 (requires installation kit sold separately) C. XR700 Ignition Module and Optical Trigger For 12 Volt Negative or Positive Ground (requires installation kit sold separately) D. Installation Kits Includes shutters and brackets for installation of optical trigger on domestic 4, 6 and 8 cylinder and VW/Bosch 009 breaker point distributor applications Includes shutters and brackets for installation of optical trigger on most import 4, 6 and 8 cylinder breaker point applications. Also used as universal installation kit for many other breaker point applications Includes shutters and brackets for installation of optical trigger on imports with 4 and 6 cylinder engines equipped with certain Bosch, Hitachi, or Nippondenso OE Electronic Ignition Modules. For applications where the OE module has failed and must be eliminated Includes shutters and brackets for installation of optical trigger on British imports with 4, 6 and 8 cylinder engines equipped with Lucas OPUS distributors. For applications where the OPUS module has failed and must be eliminated. Note that the HI-6S is not compatible with 12 cylinder engines. A. B. C. D Includes shutters and brackets for installation of optical trigger on Mallory YL Dual Point and unilite 8 cylinder distributor applications. TECH TIPS: BALLAST RESISTANCE How can I tell if my vehicle has ballast resistance? Here s a quick test for ballast resistance. run the engine at fast idle and measure battery voltage using a volt meter. It should be about 14 volts. Then measure the voltage at the COIL+ terminal. If there is a difference of more than 3 volts, a ballast resistor is present. When is a ballast resistor required? A ballast resistor is required only with XR700 systems. Without proper ballast resistance, the XR700 and coil will overheat and fail. All vehicles with original equipment points ignition are factory equipped with ballast resistance. This can be in the form of a ceramic ballast resistor or a resistance wire between the ignition key and COIL- terminal. It can also be in the form of internal resistance within the coil, such as Bosch blue coils (typical on VW) and Lucas coils found on older British vehicles. What do I need to do about ballast resistance when installing an XR700? If the vehicle had points and you are keeping the original coil, you do not need to do anything else. If you are changing coils and your vehicle has a ceramic ballast resistor or resistance wire, everything should still be OK. follow the coil installation instructions. If you are changing coils and your original coil had internal ballast resistance, you must add a ballast resistor (usually supplied with the coil). Use a volt-ohmmeter to check the original coil. Coils with internal ballast resistance will read at 3 ohms or more FAX 405
5 Points Conversion Ignitions XR3000 Points-To-Electronic Ignition All new status LED light for easy diagnostics. 150% greater spark gap energy over stock points ignition. Uses high output coil without ballast resistor. Optical trigger for precise ignition timing accuracy. Converts points type distributor to electronic ignition. Fully sealed for protection from dirt, moisture and vibration. SMT = Surface Mount Technology for reduced size and greater reliability. Short circuit protection. XR3000 is the high performance version of the XR States Legal XR3000 System 6 to 18 volts, reverse polarity protected, negative ground. Not compatible with 6 volt electrical systems as these may drop below 4 volts during cranking. For Domestic 4, 6 and 8 Cylinder and VW/Bosch 009 Distributor. 12 Volt Negative Ground Only and earlier noncomputer controlled vehicles. CARB E.O. D Coil current limit RPM range 4.5 amps internal short circuit protection limit set at 7 amps. 6,500 RPM For Import and Universal 4, 6 and 8 Cylinder. 12 Volt Negative Ground Only. CARB E.O. D Primary voltage output Primary energy output 400 volts (inductive discharge) 90 millijoules with PS91 coil. IGNITION For Replacement of Bosch, Hitachi, and Nippondenso 4 and 6 Cylinder OE Electronic Ignition Modules vehicles. CARB E.O. D Recommended Coils Peak spark gap current Spark duration Dimensions 100 milliamps with PS91 coil microseconds at 2,000 RPM 5 L x 3 W x 1-1/2 H, 1-1/2 lbs. PS50, Black,Canister Style PS60, Chrome, Canister Style PS91, E-Core Coil with Plated-Steel Bracket LX91 E-Core Coil with Aluminum Bracket CRANECAMS.COM
6 Points Conversion Ignition XR3000 Replacement Parts And Optional Accessories A. XR3000 Ignition Module For 12 Volt Negative Ground Only (does not include optical trigger or required installation kit) B. Optical Trigger For XR3000 (requires installation kit sold separately) A. C. XR3000 Ignition Module and Optical Trigger For 12 Volt Negative Ground Only (requires installation kit sold separately) D. Installation Kits Includes shutters and brackets for installation of optical trigger on domestic 4, 6 and 8 cylinder and VW/Bosch 009 breaker point distributor applications Includes shutters and brackets for installation of optical trigger on most import 4, 6 and 8 cylinder breaker point applications. Also used as universal installation kit for many other breaker point applications Includes shutters and brackets for installation of optical trigger on imports with 4 and 6 cylinder engines equipped with certain Bosch, Hitachi, or Nippondenso OE Electronic Ignition Modules. For applications where the OE module has failed and must be elminated. B. C. D FAX 407
Spark. FUEL. AIR. TECHNOLOGY.
FUEL. AIR. Spark. TECHNOLOGY. As you can see with the FAST Ignition Catalog, we are working hard to put a lot more SPARK into Fuel Air Spark Technology! We ve always had the ability to control the spark
More informationIGNITION INSPECTION DISTRIBUTOR ALIGNMENT AND DISASSEMBLY
INSTALLATION INSTRUCTIONS for XR700 and XR3000 LY ED SYSTEM Part Numbers 700-0226, 700-0231, 700-0292, 700-0300, 700-0309, 3000-0226, 3000-0231, and 3000-0292 CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE
More information12-Volt Negative Ground Installation Instructions
12-Volt Negative Ground Installation Instructions For Part Number: 1183 CAUTION!!! Before installing, please read the following important information... 1. The Ignitor is designed for 12-Volt negative
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRM34418 (REV. B) 09/17 UNILITE DISTRIBUTOR This product is applicabl e to pre-1966 California and pre-1968 federally certified passenger cars. It is also applicable to non-emission
More informationINSTALLATION INSTRUCTIONS for. FC 2000 Series
INSTALLATION INSTRUCTIONS for Fire Control (FC) Ignition System FC 2000 Series Owners Manual Introduction...2 Specifications...2 Coil Compatibilities...2 Wire Functions...2 Connections...3-6 Connections
More informationMallory HyFire Electronic Ignition Control
Mallory HyFire Electronic Ignition Control PN 690 Parts Included: 1 - Ignition 1 - Harness, Mag Pickup 1-18" Ground Wire 1-100V/1A Diode 4 - Mounting Screws WARNING: During installation, disconnect the
More informationOFF-ROAD ELECTRONIC IGNITION CONTROL
INSTALLATION INSTRUCTIONS FORM 1678M 05/07 OFF-ROAD ELECTRONIC IGNITION CONTROL GENERAL INFORMATION This ignition includes a single stage RPM limiter. You can set various settings using the switches that
More informationWiring Diagram 7 Amp 2 Step (7642MC) Ignition Box - No Booster ENGINE BLOCK LOWER LIMIT ARMING WIRE ORANGE GREEN BLACK DISTRIBUTOR LOOM (PRE-MADE)
Wiring Diagram 7 Amp 2 Step (7642MC) Ignition Box - No Booster IGNITION SWITCH 7 AMP 2 STEP TO TACH 7642MC LOWER LIMIT ARMING WIRE WHITE ENGINE BLOCK DISTRIBUTOR LOOM (PRE-MADE) DISTRIBUTOR COIL BATTERY
More informationMSD 7AL-2 Plus Ignition PN 7222
MSD 7AL-2 Plus Ignition PN 7222 Note: Solid Core spark plug wires cannot be used with an MSD Ignition. Note: An MSD cannot be used on vehicles with CD ignitions or distributorless ignition systems. Parts
More informationBefore performing spark test, ensure ignitor is properly grounded.
Page 1 of 10 IGNITION CHECKS SPARK TEST NOTE: Before performing spark test, ensure ignitor is properly grounded. 1. Disconnect high tension coil wire from distributor. Hold coil wire approximately 1/2"
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 275+ & 300+ STREET / STRIP DIGITAL MULTI-STRIKE CD IGNITION CONTROLLER GENERAL INFORMATION The features of the 275+ and 300+ Ignitions are the same, with one exception: the 300+
More informationACCEL SUPER BOX P/N 61212
FRM 34395 INSTALLATION INSTRUCTIONS ACCEL SUPER BOX P/N 61212 PARTS INCLUDED: (x1) Ignition (x1) 18 Ground Wire (x4) Mounting Screws (x1) Harness (x1) 100V/1A Diode WARNING! During installation, disconnect
More informationMallory HyFire Electronic Ignition Control
Mallory HyFire Electronic Ignition Control PN 690 Parts Included: 1 - Ignition 1 - Harness, Mag Pickup 1-18" Ground Wire 1-100V/1A Diode 4 - Mounting Screws WARNING: During installation, disconnect the
More informationSTREET/RACE DISTRIBUTOR
Installation Instructions for STREET/RACE DISTRIBUTOR CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION INTRODUCTION The Crane Cams street/race distributor is a high precision system intended
More information1.0 Installation Wiring
1.0 Installation Wiring DX Firebox is designed to be an electronic replacement for Pontiac & Ford buzz coils when operated on DC. Installation may be positive or negative ground. Simply observe the RED
More informationINTRODUCTION BASIC OPERATION FINAL CHECK OPERATION TEST CONNECTIONS BASIC IGNITION TESTS. For more information, see
OPERATING INSTRUCTIS for IGNITI ER AND CALIBRATOR Part Number 1-1 or more information, see www.cranecams.com CAUTI: READ INSTRUCTIS CAREULLY BEORE STARTING INSTALLATI. INTRODUCTI The Crane Ignition Tester
More informationACCEL/DFI 6A Sportsman Electronic Ignition Control Module for Distributor Equipped Engines
INSTALLATION INSTRUCTIONS FORM 1522D 3/08 REV. 13 ACCEL/DFI 6A Sportsman Electronic Ignition Control Module for Distributor Equipped Engines PARTS INCLUDED: PART NO. 75606 1 Ignition Control Module 5 1/4"
More informationP l u g n p l a y b i l l e t D i s t r i b u t o r s
PLUG n play billet distributors P l u g n p l a y b i l l e t D i s t r i b u t o r s Plug n Play billet distributors are designed for maximum ignition performance at a price you can afford. Our distributors
More informationMSD Digital 6M-3L Marine Ignition PN 6564
MSD Digital 6M-3L Marine Ignition PN 6564 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps
More informationHYFIRE 6AL2 ELECTRONIC IGNITION CONTROL
INSTALLATION INSTRUCTIONS FORM 1643 HYFIRE 6AL2 ELECTRONIC IGNITION CONTROL PART NO 6861M PARTS INCLUDED: 1 HYFIRE 6AL2 Ignition Control 4 #10 Sheet Metal Screws 2 Wire Ties 2 Ring Terminals, Insulated
More informationBSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines
BSR BSR Magic Box Digital ignition control for 4, 6, or 8 cylinder engines Features Digital Advance The main feature of the Magic Box is the digital advance that replaces conventional weights and springs.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FORM 1026 (REV. C) 06/03 MULTI STAGE (REMOTE / ADJUSTABLE IGNITION TIMING CONTROL) Part No. The Multi Stage High Speed Retard Part No. is not legal for sale or use in California
More informationStreet Fire CDI PN 5520
Street Fire CDI ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if
More informationMAX-FIRE AND E-FIRE ELECTRONIC DISTRIBUTORS
INSTALLATION INSTRUCTIONS MAX-FIRE AND E-FIRE ELECTRONIC DISTRIBUTORS NOTE: This product is applicable to pre-1966 California and pre-1968 federally certified passenger cars. It is also applicable to non-emission
More informationSTRIP ANNIHILATOR Ignition System Part Number
STRIP ANNIHILATOR Ignition System Part Number 800-200 Installation Instructions and Troubleshooting Manual One or more of the following items may be required to complete the installation of this kit. 820-200
More informationAUTOMOTIVE MAINTENANCE TECHNOLOGY SUBJECT: AUTOTRONIC 2 TITLE: BREAKER-TRIGGERED TRANSISTORISED IGNITION TI-B
Breaker-triggered transistorized ignition TI-B The ignition distributor of the breaker- triggered transistorized ignition system (TI-B) is identical to the ignition distributor of the breaker-triggered
More informationMSD Marine Ignitions 6M-2L, PN 6560
MSD Marine Ignitions 6M-2L, PN 6560 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD
More informationMSD Circle Track Ignition PN 6427
MSD Circle Track Ignition PN 6427 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD
More informationHYFIRE VI SERIES OF ELECTRONIC IGNITION CONTROLS HYFIRE VI Ignition System Part No. 685, Advanced HYFIRE VI Ignition System Part No.
FORM 1478 (REV. D) 09/2008 INSTALLATION INSTRUCTIONS HYFIRE VI SERIES OF ELECTRONIC IGNITION CONTROLS HYFIRE VI Ignition System Part No. 685, Advanced HYFIRE VI Ignition System Part No. 6851, Basic For
More informationMSD Blaster Ignition PN 5900
MSD Blaster Ignition PN 5900 Note: Read these instructions completely before attempting any installation. Parts Included: 1 - Blaster Ignition, PN 5900 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground
More informationMAGNETOS SUPER MAG SERIES MAGNETOS
SUPER MAG SERIES MAGNETOS 3536544 28900A SUPER-MAG III and SUPER MAG IV Designed specifically for use in Monster Trucks, Tractor Pulling, drag racing and other short duration motorsports applications,
More informationHYFIRE 6.6 SERIES OF ELECTRONIC IGNITION CONTROL
FORM 1486M 03/05 INSTALLATION INSTRUCTIONS HYFIRE 6.6 SERIES OF ELECTRONIC IGNITION CONTROL HYFIRE 6.6 IGNITION SYSTEM PART NO. 686M FOR APPLICATIONS TRIGGERED BY POINTS, MALLORY ELECTRONIC IGNITION DISTRIBUTOR
More informationPERTRONIX DIGITAL HP INSTALLATION INSTRUCTIONS
PERTRONIX DIGITAL HP INSTALLATION INSTRUCTIONS TABLE OF CONTENTS Specifications... 4 General Information... 5 Coil Compatibility... 6 Mounting the Digital HP... 7 Wiring... 8 User Interface... 12 Programming...
More informationMSD Digital 6 Plus Ignition Control, PN 6520
MSD Digital 6 Plus Ignition Control, PN 6520 Parts Included: 1 - MSD Ignition 2 - Violet Jumpers 4-45 Faston Terminals 1 - Harness, PN 8860 4 - Vibration Mounts and Hardware 2 - Wire Caps 1 - Harness,
More informationAccuSpark. Fitting and Information Guide For. Modules Distributors coils Tools. Modern Ignition for Classic cars
AccuSpark Modern Ignition for Classic cars Fitting and Information Guide For Modules Distributors coils Tools www.accuspark.co.uk 1 Before fitting AccuSpark Distributors AccuSpark electronic ignition kit.
More informationLadies and Gentlemen... We Have Ignition!
FEATURE Ladies and Gentlemen... We Have Ignition! The coordination of ignition, fuel delivery and basic engine function is required before internal combustion can take place. Here, we'll look at the ignition
More informationMSD 7AL-2 Plus Ignition
MSD 7AL-2 Plus Ignition PN 7222/72223 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the
More informationSensors & Controls. Everything you wanted to know about gas engine ignition technology but were too afraid to ask.
Everything you wanted to know about gas engine ignition technology but were too afraid to ask. Contents 1. Introducing Electronic Ignition 2. Inductive Ignition 3. Capacitor Discharge Ignition 4. CDI vs
More informationHow Does A Dc Cdi Ignition System Work >>>CLICK HERE<<<
How Does A Dc Cdi Ignition System Work Was hoping some poor KLR rider's CDI mounting bolts would vibrate off and I'd Our Guar-rontee: "If it doesn't look bad from a mile away, we'll drive you closer till
More informationHI-6 CD IGNITION With Rev Limiter and Timing Retard
Installation Instructions for CD With Rev Limiter and Timing Retard For more information, see www.cranecams.com CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. READ THIS BEFORE YOU BEGIN!
More informationAUTOMOTIVE MAINTENANCE TECHNOLOGY SUBJECT : AUTOTRONIC 2 TITLE: TRANSISTORISED IGNITION WITH HALL GENERATOR TI-H
Transistorized ignition with Hall generator TI-H In addition to the breaker-triggered transistorized ignition system (TI-B), there are two other versions of transistorized ignition with Hall triggering
More information75 SERIES BILLET HEI DISTRIBUTORS
INSTALLATION INSTRUCTIONS 75 SERIES BILLET HEI DISTRIBUTORS GENERAL INFORMATION Mallory 75 Series Distributors are similar to GM HEI distributors, but with many advantages over the OEM design, including:
More informationContents. DX Ignition Page 2
Contents 1.0 Intent 2.0 Specifications 3.0 Installation 4.0 Operation Precautions 5.0 Repair 6.0 Parts List 7.0 Glossary of Terms 8.0 Contact Information DX Ignition Page 2 1.0 Intent The purpose of this
More informationHYFIRE VII Series Electronic Ignition Controls Instruction Manual Part#: 667C
HYFIRE VII Series Electronic Ignition ontrols Instruction Manual Part#: 667 FORM 1460 (REV. ) 5/00 INSTALLATION INSTRUTIONS HYFIRE VII PRO D IGNITION SYSTEM Part No. 667 4-12 ylinder 6 ylinder Odd-Fire
More informationIgnition Installation Troubleshooting Tips/Frequently-Asked Questions
Ignition Installation Troubleshooting Tips/Frequently-Asked Questions Warning: Reversing the red and black ignition wires will destroy the ignition module and void the warranty. The Hot-Spark module s
More informationMSD 7AL-3, Ignition Control PN 7230
MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,
More informationProMaster Ignition Coil PN 29440
ProMaster Ignition Coil PN 29440 Parts Included: 1 - Ignition Coil 1 - Ignition Coil Bracket 1 - Screw, #10 x 1" 1 - Coil Wire Boot 1 - Coil Wire Terminal 2 - Ring Terminals 3 - Screws, #10 x 3/4" GENERAL
More information1984 Jeep CJ7. IGNITION SYSTEM - SOLID STATE' 'Distributors & Ignition Systems MOTORCRAFT SOLID STATE IGNITION (SSI)
TESTING SECONDARY CIRCUIT CHECK CAUTION: When checking secondary voltage, do not remove spark plug wires from spark plugs No. 3 on 4-cylinder, No. 1 or 5 on 6-cylinder and No. 3 or 4 on V8 Engines. 1.
More informationOPERATING INSTRUCTIONS
2 7 5 OPERATING INSTRUCTIONS PORTABLE PART NO. 28357 By functioning as a triggering device, Mallory's Portable Ignition Tester allows you to check the operation of a car s ignition system without starting
More informationAUTOMOTIVE ENGINEERING SECTION
PURPOSE OF IGNITION SYSTEM The ignition system supplies high-voltage surges as high as 47,000 volts (in some electronic systems) to the spark plugs in the engine cylinders. These surges produce electric
More informationMSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020
INSTALLATION INSTRUCTIONS 1 MSD Stacker-4 (4-Channel), PN 7010 Stacker-8 (8-Channel), PN 7020 Important: Read these instructions before attempting this installation! Parts Included: 1 - MSD Stacker Ignition
More informationMSD 6 Series Installation Instructions 6A, 6AL, 6T, 6BTM, 6TN, 6ALN
MSD 6 Series Installation Instructions 6A, 6AL, 6T, 6BTM, 6TN, 6ALN Parts Included: 1 - MSD 6 Series Ignition 1-100V/1A Diode 1 - Harness, PN 8860 4 - Wire Splicers 1 - Harness, PN 8861 2 - Wire Ties 1-18"
More informationMODULE TEST UNIT. Part No: MTU-12 V2.1
MODULE TEST UNIT Part No: MTU-12 WHITE YEL ORANGE VEHICLE RED 150 Fused + 12 Volt BLACK 150 RED + 12 Volt Out BLACK Out WHITE Pulse ( adjustable by pot) Left High LED will light over 4.5 V Left Low LED
More informationMSD-8 Plus Ignition PN 7805
MSD-8 Plus Ignition PN 7805 Note: Solid Core spark plug wires cannot be used with an MSD Ignition. Parts Included: 1 - MSD-8 Plus Ignition 1 - Mag Pickup Extension Harness, PN 8860 4 - Vibration Mounts
More informationOMC STERNDRIVE/COBRA I/O. Ignition System
18-5001➀ 18-5001N➁ AP# 13339 Replaces: 172525 18-5157 580290 Contact Set 18-5200 580256 Condenser 18-5250 AP# 21001 Replaces: 172527 18-5311 380538 Contact Set 18-5345 380537 Condenser 18-5418 384735 Rotor
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for WEGO II Wide-Band Exhaust Gas Oxygen Sensor Interface Methanol Version CAUTION: CAREFULLY READ INSTRUCTIONS
More informationCAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION
V-Twin MFG. VT No. 32-9500 V-TECH 1 IGNITION KIT, SINGLE FIRE FITS EV SHOVEL, XL THRU 1997 VT No. 32-9503 V-TECH 1 IGNITION KIT, SINGLE FIRE FITS EV, SHOVEL, XL, WITH COIL AND WIRES This is a custom application
More informationP/N 646 MODE L LOW RPM H HIGH RPM C CYLINDER SELECT P/N 646 H HIGH RPM C CYLINDER SELECT WINDOW RPM SWITCH L LOW RPM VALUE MODE MODE DOWN RED GREEN
INSTALLATION INSTRUCTIONS FORM 1008 (REV A) 01/02 WINDOW RPM ACTIVATED SWITCH PART NO 646 Parts Included in this kit: 1 RPM Activated Switch Part No 646 1 U shaped crimp-on wire terminal 1 #6 x 1/4" sheet
More informationMSD Digital-7 Plus Ignition Control PN 7520
INSTALLATION INSTRUCTIONS MSD Digital-7 Plus Ignition Control PN 7520 Parts Included: 1 - MSD Ignition 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground Wire 1 - White Jumper 1 - Red Jumper 2 - Violet
More informationMSD Pro-Billet Digital E-Curve Distributor PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor PN 8394 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue
More informationELEC4 ELECTRONIC IGNITION KIT FITTING INSTRUCTIONS
ELEC4 ELECTRONIC IGNITION KIT FITTING INSTRUCTIONS This Ignitor electronic ignition kit is designed to be used on Silver Shadow and Bentley T models from VIN8742 to 22117 (approximately) fitted with a
More informationINSTALLATION INSTRUCTIONS for HI-1 and HI-2 MOTORCYCLE IGNITIONS. Part Numbers and INTRODUCTION COIL AND SPARK PLUG CABLE CONSIDERATIONS
INSTALLATION INSTRUCTIONS for HI- and HI- MOTORCYCLE S Part Numbers 8-000 and 8-000 CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION INTRODUCTION Crane HI- and HI- ignition systems are
More informationAsynchronous Restriking CDI 2 channel
Asynchronous Restriking CDI 2 channel Parts List ARC-2 module Decals Power Cable Fuse Specifications Operating Voltage: 8-20V Operating Current: Max Operating RPM: Ambient Temp range: Ignition inputs:
More informationELECTRICAL. CDTA Technical Training Center
ELECTRICAL ATOMIC STRUCTURE Protons positive charge Electron negative charge Neutron - neutral Electricity is the movement of electrons from atom to atom ELECTRON FLOW CONDUCTOR - Materials which have
More informationMSD Pro Mag Information
MSD 44 Amp Pro Mag Generator Clockwise Rotation - PN 8130, PN 81303, PN 81305, PN 81307 Counterclockwise Rotation PN 8140, PN 81403, PN 81405, PN 81407 Parts Included In This Kit: 1 44 Amp Pro Mag Generator
More informationINSTALLATION INSTRUCTIONS for HI-4 DUAL FIRE MOTORCYCLE IGNITION. Part Number INTRODUCTION REMOVAL OF POINTS IGNITION TO 1977 MODELS
INSTALLATION INSTRUCTIONS for HI- DUAL FIRE MOTORCYCLE IGNITION Part Number -00 CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION INTRODUCTION The HI- ignition system is intended for use
More informationMSD Digital SCI+ Ignition Control, PN 6350
MSD Digital SCI Ignition Control, PN 6350 Parts Included: 1 - MSD Ignition 1 - Harness, PN 8860 1 - Parts Bag, ASY19864 WARNING: During installation, disconnect the battery cables. When disconnecting the
More informationMSD 40th Anniversary 6AL Ignition Control
MSD 40th Anniversary 6AL Ignition Control PN 6440 Congratulations on the purchase of your MSD 40th Anniversary 6AL Ignition Control! Not only is this limited edition (one of 4,000) Ignition Control going
More informationChrysler Electronic Ignition System
1 of 11 1/6/2010 11:02 PM Chrysler Electronic Ignition System Classic Winnebago's Post by: DaveVA78Chieftain on August 13, 2009, 10:15 PM Components The Chrysler Electronic Ignition System consists of
More informationMARINE OMC STERNDRIVE/OMC COBRA I/O. Ignition System NEW NEW NEW NEW NEW NEW
OMC STERNDRIVE/OMC COBRA MARINE 18-5001 Replaces: 172525 18-5157 580290 Contact Set 18-5200 580256 Condenser Replaces: 172527 18-5311 380538 Contact Set 18-5345 380537 Condenser 18-5418 384735 Rotor Delco
More informationELECTRONIC IGNITION CONVERSION KIT 1957-1974 General Motors V8 Single and Dual Point Distributors* - Part No. 38131 *Legal for use on emission controlled vehicles per CARB EO D-275-1 PRODUCT DESCRIPTION
More informationCHAPTER 6 IGNITION SYSTEM
CHAPTER 6 CHAPTER 6 IGNITION SYSTEM CONTENTS PAGE Faraday s Law 02 The magneto System 04 Dynamo/Alternator System 06 Distributor 08 Electronic System 10 Spark Plugs 12 IGNITION SYSTEM Faraday s Law The
More informationMSD Digital 6 Plus Ignition Control PN 6520
INSTALLATION INSTRUCTIONS 1 MSD Digital 6 Plus Ignition Control PN 6520 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark Plug
More informationMSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN 8503 - U.S. Patent 6820602 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor
More informationMSD Digital 6A and 6AL Ignition Control 6A - PN 6201/62013, 6AL - PN 6425/64253
INSTALLATION INSTRUCTIONS 1 MSD Digital 6A and 6AL Ignition Control 6A - PN 6201/62013, 6AL - PN 6425/64253 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will
More information1984 Toyota Pickup. IGNITION SYSTEM - NIPPONDENSO ELECTRONIC' '1984 ELECTRICAL Toyota Ignition System - Nippondenso Electronic Ignition
ADJUSTMENTS 1984 Toyota Pickup PICK-UP COIL-TO-SIGNAL ROTOR (RELUCTOR) AIR GAP 1. Using a flat, non-magnetic feeler gauge, check air gap between pick-up coil pole piece and each reluctor tooth. Gaps should
More information6EFI UNIVERSAL EFI IGNITION BOX PN 6415
6EFI UNIVERSAL EFI IGNITION BOX PN 6415 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issued with your product and helps
More informationWEIAND X-CELerator Intake Manifold P/N 7516
WEIAND X-CELerator Intake Manifold P/N 7516 351C FORD, 2V CYLINDER HEADS INSTALLATION INSTRUCTIONS APPLICATIONS: The P/N 7516 X-CELerator intake manifold is designed for square-bore carburetor applications
More informationE-STREET 2 EFI IGNITION CONTROL KIT Part #3674, 3675, 3676, 3679, 3680 INSTALLATION INSTRUCTIONS
E-STREET 2 EFI IGNITION CONTROL KIT Part #3674, 3675, 3676, 3679, 3680 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations can be
More informationMSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425
INSTALLATION INSTRUCTIONS 1 MSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm
More informationMSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425
INSTALLATION INSTRUCTIONS 1 MSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm
More informationMSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN U.S. Patent
MSD Pro-Billet Digital E-Curve Distributor Ford 289/302 PN 8503 - U.S. Patent 6820602 Important: Read these Instructions before attempting the installation. Parts Included: 1 - Digital E-Curve Distributor
More informationDISTRIBUTORLESS IGNITION SYSTEM Installation and Adjustment Instructions
DISTRIBUTORLESS IGNITION SYSTEM Installation and Adjustment Instructions 1.0 INTRODUCTION: Congratulations on your purchase of a Holley Distributorless Ignition System! Holley cannot and will not be responsible
More informationUnit AE01K Knowledge of Locating and Correcting Simple Electrical Faults in the Automotive Workplace
Assessment Requirements Unit AE01K Knowledge of Locating and Correcting Simple Electrical Faults in the Automotive Workplace Content: Basic electrical principles a. Explain the direction of current flow
More informationCAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for Wide-Band Exhaust Gas Oxygen Sensor Interface CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW
More informationMSD-8 Plus Ignition PN 7805
MSD-8 Plus Ignition PN 7805 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the MSD R&D team
More informationMSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425
INSTALLATION INSTRUCTIONS 1 MSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm
More informationATASA 5 th. ATASA 5 TH Study Guide Chapter 27 Pages Ignition Systems 68 Points. Please Read the Summary
ATASA 5 TH Study Guide Chapter 27 Pages 810 835 68 Points Please Read the Summary Before We Begin Keeping in mind the Career Cluster of Transportation, Distribution & Logistics Ask yourself: What careers
More informationSTROMBERG e-fire OWNER S MANUAL MODELS 11A/21A
STROMBERG e-fire OWNER S MANUAL MODELS 11A/21A THANK YOU for choosing a Genuine Stromberg e-fire Electronic Distributor for your Flathead Ford. This Owner s Manual will make installation and adjustment
More informationTUNE-UP - 4-CYL Jeep Cherokee IDENTIFICATION ENGINE IDENTIFICATION TUNE-UP NOTES TESTING ENGINE COMPRESSION SPARK PLUGS
TUNE-UP - 4-CYL 1988 Jeep Cherokee 1988 Jeep 4 Tune-Up TUNE-UP All Models IDENTIFICATION ENGINE IDENTIFICATION Engine can be identified by the 4th character of the Vehicle Identification Number (VIN).
More informationMSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302
MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your
More informationMSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595
MSD Pro-Billet Ready to Run Distributor Ford Y-Block, PN 8383 Ford FE, PN 8595 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you ll be entered in our monthly 8.5mm Super Conductor Spark
More informationInstallation Instructions for LED Timing Light
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW The P/N 120001 includes a versatile controller
More informationMSD SCI Series PN 6300 & PN 6320
MSD SCI Series PN 6300 & PN 6320 IMPORTANT: Read these instructions before attempting this installation! Parts Included: 1 - MSD SCI Series Ignition 1 - Harness, PN 8860 1 - Parts Bag, ASY 10506, SCI Only
More informationHOWELL INSTALLATION MANUAL. Throttle Body Fuel Injection Harness
HOWELL ENGINE DEVELOPMENTS, INC. FUEL INJECTION APPLICATIONS INSTALLATION MANUAL Throttle Body Fuel Injection Harness Howell Engine Developments, Inc. 6201 Industrial Way Marine City, MI 48039 Phone: 810-765-5100
More informationInstallation Guide for the Electronic Ignition Distributor
Installation Guide for the Electronic Ignition Distributor Remanufactured By East Coast Roadster East Coast Roadster: Ignition systems and accessories for Datsun Roadster fanatics! PLEASE, Call with any
More informationElectronic Dynamo Regulator INSTRUCTION MANUAL. COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved
DRM TM DRM-HP TM Electronic Dynamo Regulator INSTRUCTION MANUAL COPYRIGHT 2014 CLOVER SYSTEMS All Rights Reserved INTRODUCTION The Clover Systems DRM is a state-of-the art all-electronic voltage and current
More informationACCEL Distributor Model #A557
FORM 1627 REV1 INSTALLATION INSTRUCTIONS ACCEL Distributor Model #A557 CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING. NOT LEGAL FOR USE OR SALE ON POLLUTION CONTROLLED VECHICLES OVERVIEW ACCEL
More informationALTERNATOR & REGULATOR - NIPPONDENSO
ALTERNATOR & REGULATOR - NIPPONDENSO 1988 Toyota Celica 1988 ELECTRICAL Alternators & Regulators - Nippondenso Camry, Celica, Corolla, Cressida, Land Cruiser, MR2, Pickup, Supra, Tercel, Van, 4Runner DESCRIPTION
More informationIgnition System Fundamentals
Ignition System Fundamentals Chapter 37 Objectives Describe the functions of ignition system parts Explain the operation of points, electronic, and computer ignition systems Give an overview of the different
More information