MODEL: G-25 WITH METALLIC PUMP HEAD
|
|
- Britton Park
- 6 years ago
- Views:
Transcription
1 PARTS MANUAL G B MODEL: G-25 WITH METALLIC PUMP HEAD IMPORTANT Record your pump model number and serial number here for easy reference: Model No. Serial No. Date of Purchase When ordering parts or making inquiries about this pump, please mention the model and serial numbers. W0192A WANNER ENGINEERING, INC Chestnut Avenue, Minneapolis, MN TEL: (612) FAX: (612) TOLL-FREE FAX [US only]: (800)
2 G-25 Fluid End (with metallic pump head) Not included with brass pump heads Note: Contact factory for pumps with Serial Numbers or below. 1 G Cap Screw, socket head, M12 x 1.25 x 114 mm G Washer, 13 cm, flat D O-ring, centerbolt, Buna D O-ring, centerbolt, Viton D O-ring, centerbolt, Neoprene D O-ring, centerbolt, EPDM D O-ring, centerbolt, Teflon D Plug, Hastelloy C...1 D Plug, 316 SST G Cap Screw, socket-head, M10 x 1.5 x 120 mm G Washer, split-lock, M D Manifold, brass...1 D Manifold, 316 SST...1 D Manifold, cast iron...1 D Manifold, nickel alloy, Hastelloy CW12MW D O-ring, center manifold, Buna D O-ring, center manifold, Viton D O-ring, center manifold, Neoprene 1..1 D O-ring, center manifold, EPDM D O-ring, center manifold, Teflon G B
3 G-25 Fluid End (with metallic pump head) 9 D Oring, inner manifold, Buna...1 D O-ring, inner manifold, Viton...1 D O-ring, inner manifold, Neoprene...1 D O-ring, inner manifold EPDM...1 D O-ring, inner manifold, Teflon D O-ring, outer manifold, Buna D O-ring, outer manifold, Viton D O-ring, outer manifold Neoprene D O-ring, outer manifold EPDM D O-ring, outer manifold, Teflon D O-ring, valve seat, Buna...6 D O-ring, valve seat, Viton...6 D O-ring, valve seat, Neoprene...6 D O-ring, valve seat, EPDM...6 D O-ring valve seat, Teflon D Valve Seat, 17-4 HT SST...6 D Valve Seat, Nitronic D Valve Seat, tungsten carbide...6 D Valve Seat, Hastelloy C...6 D Valve Seat, ceramic D Valve, 17-7 HT SST. stamped...6 D Valve, Nitronic D Valve, 17-4 HT SST, machined...6 D Valve, tungsten carbide...6 D Valve, Hastelloy C...6 D Valve, ceramic D Valve Spring, 17-7 HT SST...6 D Valve Spring, Elgiloy...6 D Valve Spring, Hastelloy C D Tetra Seal, Buna...6 D Tetra Seal, Viton...6 D Tetra Seal, Neoprene...6 D Tetra Seal, EPDM...6 D O-ring, Teflon ( not a Tetra Seal ) D Retainer, valve spring, 17-7 HT SST...6 D Retainer, valve spring, Hastelloy C...6 D Retainer, valve spring, Celcon...6 D Retainer, valve spring, Nylon...6 D Retainer, valve spring, polypropylene 6 D Retainer, valve spring, Kynar D O-ring, outlet valve, Buna D O-ring, outlet valve, Viton D O-ring, outlet valve, Neoprene D O-ring, outlet valve, EPDM D O-ring, outlet valve, Teflon D Valve Plate, brass...1 D Valve Plate, 316 SST...1 D Valve Plate, cast iron...1 D Valve Plate, nickel alloy C series D Screw, flat-head, 5/8, 316 SST...3 D Screw, flat-head, 5/8, Hastelloy C D O-ring, follower, Buna...3 D O-ring, follower, Viton...3 D O-ring, follower, Neoprene...3 D O-ring, follower, EPDM...3 D O-ring, follower, Teflon D Follower, 316 SST...3 D Follower, Hastelloy C D Diaphragm, Neoprene...3 D Diaphragm, EPDM...3 D Diaphragm, Viton-XT...3 D Diaphragm, Teflon...3 D Diaphragm, Buna-N-XS D Plunger G Set Screw, M6 x 1 x 16 mm G Cylinder Housing...1 G Cylinder Housing Assembly 3... K Cylinder Housing, Kel-Cell...1 K Cylinder Housing Assembly, Kel-Cell G Cap Screw, socket-hd, M10 x 1.5 x 30 mm D O-ring, oil fill, Buna D Cap with O-ring, oil fill D Name Plate G Pump Housing Assembly 4... G Pump Housing G Nut, hex, M D Elbow, 3/ D Pipe, 3/ D Cap, 3/ D Base G Washer, shakeproof, M G Cap Screw, hex-hd, M10 x 1.5 x 25 mm D Washer, dampening, 316 SST D Washer, dampening, Hastelloy C D Washer, dampening, Celcon (Delrin) D Washer, dampening, Nylon D Washer, dampening, polypropylene 5 6 D Washer, dampening, Kynar G Cap Screw, socket-hd, M6 x 1x 45 mm G Gasket, cover H Cover, housing G Cap Screw, hex-head With brass external-centerbolt models, use Ref #8; with all other models, use Ref #3. 2 With cast iron pump heads, use Ref #17 and not Ref #10; with all other models, use Ref #10 and not Ref # Cylinder Housing Assembly includes housing (25), bearing adjusting plate (61), O-ring (60), screws (24), and bearing cup (62A). 4 Pump Housing Assembly includes housing (30), gasket (40), cover (41), screws (42), oil drain (32, 33, 34), and bearing cup (62B). 5 Not required on all pumps. 3 G B
4 G-25 Hydraulic End (with metallic pump head) W0197A 4 G B
5 G-25 Hydraulic End (with metallic pump head) 50 D Spring, piston return D Retainer, piston return spring D O-ring, valve cylinder, Buna D Spring, sleeve valve...3 K Spring, sleeve valve, Kel-Cell D Valve Plunger...3 K Valve Plunger, Kel-Cell D Cylinder, valve...3 K Cylinder, valve, Kel-Cell D O-ring, Buna D Washer, ball retainer D Ball, 1/ D Piston, with foot and retainer...3 D Piston Assembly 1... K Piston Assembly, Kel-Cell D O-ring, bearing adjusting plate, Buna.1 61 D Bearing Adjusting Plate H (X) Cam Assembly, RPM H (I) Cam Assembly, RPM H (S) Cam Assembly, RPM H (E) Cam Assembly, RPM D Key, shaft H Seal, Buna, 1-1/ H O-ring, pump housing, Buna, Ser. No & above...1 D Label, caution Piston Assembly includes cylinder, foot, valve plunger, O- rings, spring retainer, and springs (50-59). 2 Cam Assembly includes cam, shaft, wobble plate, bearings, and cups. It is only available as an assembly. 5 G B
6 G-25 Series Replacement Parts Kits (with metallic pump head) ORDERING INFORMATION: A Replacement Parts Kit contains 11 digits corresponding to customer-specified design options Order Digit Code Description 1-3 Pump Configuration G25 For all G-25 Pumps 4 Kit Designator K Complete Fluid End Kit D Diaphragm Kit V Valve Kit (diaphragm not included) 5-6 Pump Head Version 52 Metallic Pump Head Version 7 Diaphragm & O-ring Material E EPDM G Viton-XT J Teflon P Neoprene T Buna-N-XS 8 Valve Seat Material C Ceramic D Tungsten Carbide H 17-4 PH Stainless Steel N Nitronic 50 9 Valve Material C Ceramic D Tungsten Carbide F 17-7 PH Stainless Steel Machined H 17-7 PH Stainless Steel Stamped N Nitronic Valve Springs E Elgiloy H 17-7 PH Stainless Steel 11 Valve Spring Retainers C Celcon H 17-7 PH Stainless Steel M Kynar P Polypropylene Y Nylon (Zytel) Kit Contents Kit Designator Part Number* Description Qty K D V D Diaphragm 3 D O-ring, follower 3 D O-ring, outlet valve 3 D O-ring, outer manifold 1 D O-ring, inner manifold 1 D O-ring, center manifold 1 1 D O-ring, center bolt 2 1 D O-ring, valve seat 6 D Valve seat 6 D Valve 6 D Valve spring 6 D Tetra seal 3 6 D Retainer, valve spring 6 A Threadlocker 1 * Last four digits of part numbers with refer to specific material of construction. 1 D is provided for brass head only. 2 D is provided for head other than brass. 3 Not included with metal spring retainers. WANNER ENGINEERING, INC Chestnut Avenue, Minneapolis, MN TEL: (612) FAX: (612) TOLL-FREE FAX [US only]: (800) sales@wannereng.com Wanner Engineering, Inc. Printed in USA G B 5/2004, Revised 11/2006
Models: G-25, H-25 With Non-Metallic Pump Head
Parts Manual G25-991-2403B Models: G-25, H-25 With Non-Metallic Pump Head WANNER ENGINEERING, INC. W0193B 1204 Chestnut Avenue, Minneapolis, MN 55403 TEL: (12) 332-581 FAX: (12) 332-937 TOLL-FREE FAX [US
More informationModels: G-25, H-25 With Metallic Pump Head
Parts Manual G5-99-40C Models: G-5, H-5 With Metallic Pump Head W09B WANNER ENGINEERING, INC. 04 Chestnut Avenue, Minneapolis, MN 55403 TEL: () 33-58 FAX: () 33-937 TOLL-FREE FAX [US only]: (800) 33-8
More informationModel: D-10. Parts Manual D B. with non-metallic pump head WANNER ENGINEERING, INC. IMPORTANT
Parts Manual D10-991-2403B Model: D-10 with non-metallic pump head IMPORTANT Record your pump model number and serial number here for easy reference: Model No. Serial No. Date of Purchase When ordering
More informationModels: D-12, G-12. Parts Manual D D WANNER ENGINEERING, INC.
Parts Manual D12-991-2402D Models: D-12, G-12 IMPORTANT Record your pump model number and serial number here for easy reference: Model No. Serial No. Date of Purchase When ordering parts or making inquiries
More informationINDUSTRIAL PUMPS MODEL: D-35 PARTS MANUAL WANNER ENGINEERING, INC. IMPORTANT
PARTS MANUAL INDUSTRIAL PUMPS IMPORTANT Record your pump model number and serial number here for easy reference: MODEL: D-35 Model No. Serial No. Date of Purchase When ordering parts or making inquiries
More informationMODELS: G-20, G-21, G-22
PARTS MANUAL G20-991-2402A IMPORTANT Record your pump model number and serial number here for easy reference: Model No. MODELS: G-20, G-21, G-22 Serial No. Date of Purchase When ordering parts or making
More informationINDUSTRIAL PUMPS PARTS MANUAL MODELS: M-03 D-03 M-23 M-24 G-03 G-13 WANNER ENGINEERING, INC. IMPORTANT
PARTS MANUAL IMPORTANT Record your pump model number and serial number here for easy reference: INDUSTRIAL PUMPS MODELS: M-03 D-03 M-23 M-24 G-03 G-13 Model No. Serial No. Date of Purchase When ordering
More informationHydracel High Pressure Pump
Hydracel High Pressure Pump Mfg: Hydracell Model: D10 SL SE SHEHC Stock No. HDPH038.5a Serial No. 99260 Hydracell High pressure Pump. Model D10 SL SE SHEHC, S/N 99260. Inlet (1) 1-1/2 in., Outlet (1) 1
More informationModels: D-03, G-03, G-13 and M-03
Parts Manual D03-991-2402C Models: D-03, G-03, G-13 and M-03 Kel-Cell and Standard Versions IMPORTANT Record your pump model number and serial number here for easy reference: Model No. Serial No. Date
More informationINDUSTRIAL PUMPS MODEL: D-35-SD PARTS MANUAL SLURRY DUTY PUMP WANNER ENGINEERING, INC. IMPORTANT
PARTS MANUAL INDUSTRIAL PUMPS IMPORTANT Record your pump model number and serial number here for easy reference: Model No. MODEL: D-35-SD SLURRY DUTY PUMP Serial No. Date of Purchase When ordering parts
More informationINDUSTRIAL PUMPS PARTS MANUAL. MODELS: C-22, C-23, C-24 Bypass Pressure Regulating Valves WANNER ENGINEERING, INC. IMPORTANT
PARTS MANUAL IMPORTANT Record your pump model number and serial number here for easy reference: Model No. Serial No. Date of Purchase When ordering parts or making inquiries about this pump, please mention
More informationModels: D-03, G-03, G-13, M-03 and M-23 Mono-Block Kel-Cell Versions
Parts Manual D03-991-2406 Models: D-03, G-03, G-13, M-03 and M-23 Mono-Block Kel-Cell Versions IMPORTANT Record your pump model number and serial number here for easy reference: Model No. Serial No. Date
More informationH/G-25 Series. Up to 20 gpm (75.7/min) H/g-25 hydra-cell diaphragm pump. H/G-25 Specialized Designs
H/g-25 hydra-cell diaphragm pump H/G-25 Series Up to 2 gpm (75.7/min) H/G-25 Specialized Designs Hydra-Cell Slurry Duty pumps are specifically designed for abrasive slurry applications. See page 8 for
More informationH/G-25 Series. Up to 20 gpm (75.7/min) H/G-25 Specialized Designs
H/G-25 Series Up to 2 gpm (75.7/min) H/G-25 Specialized Designs Hydra-Cell Slurry Duty pumps are specifically designed for abrasive slurry applications. See page 8 for complete specifications. The H-25
More informationD/G-10 Series. Up to 8 gpm (30.3 l/min) D/g-10 hydra-cell diaphragm pump. D/G-10 Specialized Designs
D/g-1 hydra-cell diaphragm pump D/G-1 Series Up to 8 gpm (3.3 l/min) D/G-1 Specialized Designs Hydra-Cell Slurry Duty pumps are specifically designed for abrasive slurry applications. See page 8 for complete
More informationD/G-35 Series. Up to 37gpm (140 l/min) D/g-35 hydra-cell diaphragm pump. D/G-35 Specialized Designs
D/g-35 hydra-cell diaphragm pump D/G-35 Series Up to 37gpm (14 l/min) D/G-35 Specialized Designs Hydra-Cell Slurry Duty pumps are specifically designed for abrasive slurry applications. See page 8 for
More informationD/G-12 Series. Up to 8 gpm (30.3 l/min)
D/G-12 Series Up to 8 gpm (3.3 l/min) D/G-12 Vertical Applications The D/G-12 is specifically designed for vertical pumping installations such as machine tool cooling applications. D/G-12 shown with Hydra-Cell
More informationVersatile, Reliable Pumps for a Wide Range of Applications H25 Series
Versatile, Reliable Pumps for a Wide Range of Applications H25 Series Pumps the full spectrum of low-to-high viscosity fluids. Features a seal-less design and horizontal disk check valves that enable the
More informationVersatile, Reliable Pumps for a Wide Range of Applications D10 Series
Versatile, Reliable Pumps for a Wide Range of Applications D10 Series Pumps the full spectrum of low-to-high viscosity fluids. Features a seal-less design and horizontal disk check valves that enable the
More informationVersatile, Reliable Pumps for a Wide Range of Applications D35 Series
Versatile, Reliable Pumps for a Wide Range of Applications D35 Series Pumps the full spectrum of low-to-high viscosity fluids. Features a seal-less design and horizontal disk check valves that enable the
More informationF/G-20 Series. Up to 1.0 gpm (3.8 l/min) f/g-20 hydra-cell diaphragm pump
f/g-20 hydra-cell diaphragm pump F/G-20 Series Up to 1.0 gpm (3.8 l/min) F/G-22 with Pump/Motor Adapter for coupling to NEMA C-Face and IEC B5 Flange motors F/G-20 hollow shaft for close coupling with
More informationG10 Series API bar (350 psi) for Non-metallic Pump Heads. G10 with Cast Iron pump head
G10 Series Maximum Flow Rate: Maximum Pressure: 33.4 l/min (8.8 gpm) 103 bar (1500 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads API 674 ATEX G10 with Cast Iron pump head G10
More informationG25 Series API bar (350 psi) for Non-metallic Pump Heads. G25 with Cast Iron pump head
G25 Series Maximum Flow Rate: Maximum Pressure: 76 l/min (20.0 gpm) 69 bar (1000 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads API 674 ATEX G25 with Cast Iron pump head G25
More information69 bar (1000 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads
G25 Series Maximum Flow Rate: Maximum Pressure: 76 l/min (20.0 gpm) 69 bar (1000 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads API 674 ATEX G25 with Cast Iron pump head G25
More information103 bar (1500 psi) for Metallic Pump Heads
G35 Series Maximum Flow Rate: Maximum Pressure: 138 l/min (36.5 gpm) 13 bar (15 psi) for Metallic Pump Heads API 674 ATEX G35 with Stainless Steel pump head and SAE flanges G35 with Brass pump head G35
More informationG10 Series API bar (350 psi) for Non-metallic Pump Heads. G10 with Cast Iron pump head
G10 Series Maximum Flow Rate: Maximum Pressure: 33.4 l/min (8.8 gpm) 103 bar (1500 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads API 674 ATEX G10 with Cast Iron pump head G10
More informationModels: C22D, C23D, C24D
Installation & Service C22-991-2401A Models: C22D, C23D, C24D Bypass Pressure Regulating Valves with BSPT Threaded Ports IMPORTANT Record your pump model number and serial number here for easy reference:
More informationD/G-04 Series. Up to 3.0 gpm (11.3 l/min)
D/G-4 Series Up to 3. gpm (11.3 l/min) 42 United States Instant Information: United Kingdom D/G-4 Series Performance flow max max flow input model gpm l/min rpm D/G-4-X 2.9 11. 175 D/G-4-E 2.1 7.8 175
More informationG35 Series API bar (1500 psi) for Metallic Pump Heads. G35 with Stainless Steel pump head and SAE flanges. G35 with Brass pump head
G35 Series Maximum Flow Rate: Maximum Pressure: 138 l/min (36.5 gpm) 103 bar (1500 psi) for Metallic Pump Heads API 674 ATEX G35 with Stainless Steel pump head and SAE flanges G35 with Cast Iron pump head
More informationG10 Series API bar (350 psi) for Non-metallic Pump Heads. G10 with Cast Iron pump head
G1 Series Maximum Flow Rate: Maximum Pressure: 33.4 l/min (8.8 gpm) 13 bar (15 psi) for Metallic Pump Heads 24 bar (35 psi) for Non-metallic Pump Heads API 674 ATEX G1 with Cast Iron pump head G1 with
More informationVersatile, Reliable Pumps for a Wide Range of Applications M03 Series
Versatile, Reliable Pumps for a Wide Range of Applications M03 Series Pumps the full spectrum of low-to-high viscosity fluids. Features a seal-less design and horizontal disk check valves that enable the
More informationVersatile, Reliable Pumps for a Wide Range of Applications M03 Series
Versatile, Reliable Pumps for a Wide Range of Applications M03 Series Pumps the full spectrum of low-to-high viscosity fluids. Features a seal-less design and horizontal disk check valves that enable the
More informationP200 Metering Pump. Installation & Service P A WANNER ENGINEERING, INC. Metallic Pump shown (Motor Optional)
P200 Metering Pump Installation & Service P200-991-2400A WANNER ENGINEERING, INC. Metallic Pump shown (Motor Optional) 1204 Chestnut Avenue, Minneapolis, MN 55403 TEL: (612) 332-5681 FAX: (612) 332-6937
More informationT100 Series High Pressure
T100 Series High Pressure Maximum Flow Rate: 26 gpm (98.4 l/min) Maximum Pressure: T100 Series high pressure model with Nickel Aluminum Bronze pump head Available to Meet API 674! Seal-less design eliminates
More informationC Series Valves C24 1-1/4 NPT C23 1 NPT C22 3/4 NPT. C22/C23/C24 Series. Stainless Steel Off-Line Brass Off-Line. Brass In-Line.
C Series Valves Accurate, repeatable Minimal pressure surge Smooth, chatter-free bypass Adjustable Easy to service No external springs or moving parts Various seal material Stainless steel or brass bodies
More informationT100 Series Medium Pressure Models T100K & T100M
T100 Series Medium Pressure Models T100K & T100M Maximum Flow Rate: 45 gpm (170.4 l/min) Maximum Pressure: 3500 psi (241 bar) T100 Series medium pressure model with Nickel Aluminum Bronze pump head Available
More informationP400 Metering Pump. Installation, Operation & Maintenance P C. Metallic pump shown W0014B
TM P400 Metering Pump Installation, Operation & Maintenance P400-991-2400C W0014B Metallic pump shown 1204 Chestnut Avenue, Minneapolis, MN 55403 Tel: (612) 332-5681 Fax: (612) 332-6937 Toll-free fax [US
More informationG03 Series. 24 bar (350 psi) for Non-metallic Pump Heads. G03 Shaft-driven with Stainless Steel pump head
G03 Series Maximum Flow Rate: Maximum Pressure: 11.7 l/min (3.1 gpm) 103 bar (1500 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads ATEX G03 Shaft-driven with Stainless Steel pump
More informationVersatile, Reliable Pumps for a Wide Range of Applications D66 Series
Versatile, Reliable Pumps for a Wide Range of Applications D66 Series Pumps the full spectrum of low-to-high viscosity fluids. Features a seal-less design and horizontal disk check valves that enable the
More informationT100 Series Medium Pressure Models T100K & T100M
T100 Series Medium Pressure Models T100K & T100M Maximum Flow Rate: Maximum Pressure: 45 gpm (170.4 l/min) 1543 BPD 3500 psi (241 bar) T100 Series medium-pressure model with Nickel Aluminum Bronze pump
More informationT100 Series Low Pressure Models T100E, T100F & T100H
T100 Series Low Pressure Models T100E, T100F & T100H Maximum Flow Rate: Maximum Pressure: 96 gpm (366.1 l/min) 3292 BPD 2100 psi (145 bar) T100 Series low-pressure model with Nickel Aluminum Bronze (NAB)
More informationG03 Series Dosing Range
G03 Series Dosing Range Maximum Flow Rate: Maximum Pressure: up to 462 l/hr (122 gph) up to 103 bar (1500 psi) for Metallic Pump Heads up to 24 bar (350 psi) for Non-metallic Pump Heads AEX G13-M2M with
More informationG15 Series API bar (2500 psi) for Metallic Pump Heads. G15 for horizontal installations shown with Stainless Steel pump head.
G15 Series Maximum Flow Rate: Maximum Pressure: 58.7 l/min (15.5 gpm) 172 bar (2500 psi) for Metallic Pump Heads API 674 ATEX G15 for horizontal installations shown with Stainless Steel pump head. G15
More informationVersatile, Reliable Pumps for a Wide Range of Applications M03 Mono-Block Series
Versatile, Reliable Pumps for a Wide Range of Applications M03 Mono-Block Series Pumps the full spectrum of low-to-high viscosity fluids. Features a seal-less design and horizontal disk check valves that
More informationP100 Metering Pump. Installation & Service P A WANNER ENGINEERING, INC. Metallic Pump shown (Motor Optional)
P100 Metering Pump Installation & Service P100-991-2400A WANNER ENGINEERING, INC. Metallic Pump shown (Motor Optional) 1204 Chestnut Avenue, Minneapolis, MN 55403 TEL: (612) 332-5681 FAX: (612) 332-6937
More informationG20 Series. 24 bar (350 psi) for Non-metallic Pump Heads. G20 Close-coupled with Brass pump head ATEX. G20 Version 5 10/16
G20 Series Maximum Flow Rate: Maximum Pressure: 3.8 l/min (1.0 gpm) 103 bar (1500 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads ATEX G20 Close-coupled with Brass pump head G21
More informationF20 Series. Maximum Flow Rate: 1.0 gpm (3.8 l/min) Maximum Pressure: 1500 psi (103 bar) for Metallic Pump Heads
F2 Series Maximum Flow Rate: 1. gpm (3.8 l/min) Maximum Pressure: 15 psi (13 bar) for Metallic Pump Heads F2 Series Performance Capacities Max. Max. Flow Input @ 1 psi (69 bar) Model rpm gpm l/min F2-E
More informationG66 Series API bar (250 psi) for Non-metallic Pump Heads. G66 with Ductile Iron pump head. G66 with Polypropylene pump head.
G66 Series Maximum Flow Rate: Maximum Pressure: 248.7 l/min (65.7 gpm) 48 bar (7 psi) for Metallic Pump Heads 17 bar (25 psi) for Non-metallic Pump Heads API 674 ATEX G66 with Ductile Iron pump head www.hydra-cell.eu
More informationM03 Series. Maximum Flow Rate: 3.1 gpm (11.7 l/min) Maximum Pressure: 1200 psi (83 bar) for Metallic Pump Heads
M3 eries Maximum Flow Rate: 3.1 gpm (11.7 l/min) Maximum Pressure: 12 psi (83 bar) for Metallic Pump Heads M3 eries Performance Capacities Max. Max. Flow Input @ 1 psi (69 bar) Maximum Inlet Pressure Model
More informationG04 Series. Maximum Flow Rate: 11.2 l/min (2.9 gpm) Maximum Pressure: 200 bar (2900 psi) for Metallic Pump Heads. G04 with Stainless Steel pump head
G04 Series Maximum Flow Rate: 11.2 l/min (2.9 gpm) Maximum Pressure: 200 bar (2900 psi) for Metallic Pump Heads ATEX G04 with Stainless Steel pump head G04 with Brass pump head G04 with Stainless Steel
More informationC22A Parts. Brass Body. C22AA, C22AB, and C22AC. No. Part Number Description Pump
C22A Parts C22AA, C22AB, and C22AC 1 C22-004-1005 Adjusting bolt, Pressure range A...1 C22-004-1006 Adjusting bolt, Pressure range B, C...1 2 C22-005-1000 Jam nut...1 3 C22-015-2000 Screw, Cap, 5/16 x
More informationWANNER ENGINEERING INC
Industrial Pumps WANNER ENGINEERING INC Durability, performance and simplicity of design make Hydra-Cell pumps the optimum choice for the widest range of pump applications. When we say Simply Built to
More informationT100 Series Low Pressure Models T100E, T100F & T100H
T100 Series Low Pressure Models T100E, T100F & T100H Maximum Flow Rate: Maximum Pressure: 366 l/min (96 gpm) 145 bar (2100 psi) API 674 T100 Series low pressure model with Stainless Steel pump head Available
More informationModels: D35, G35. Installation, Operation & Maintenance D B
Installation, Operation & Maintenance D35-991-2400B Models: D35, G35 W0172B 1204 Chestnut Avenue, Minneapolis, MN 55403 Tel: (612) 332-5681 Fax: (612) 332-6937 Toll-free fax [US only]: (800) 332-6812 www.hydra-cell.com/metering
More informationP300 Metering Pump. Installation & Service P A WANNER ENGINEERING, INC.
P300 Metering Pump Installation & Service P300-991-2400A WANNER ENGINEERING, INC. 1204 Chestnut Avenue, Minneapolis, MN 55403 TEL: (612) 332-5681 FAX: (612) 332-6937 TOLL-FREE FAX [US only]: (800) 332-6812
More informationG20 Series. G20 Close-coupled with Brass pump head ATEX. G20 Version 1 01/15
G20 Series Maximum Flow Rate: 3.8 l/min (1.0 gpm) Maximum Pressure: 103 bar (1500 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads AEX G20 Close-coupled with Brass pump head G21
More informationT100 Series Medium Pressure Models T100K & T100M
T100 Series Medium Pressure Models T100K & T100M Maximum Flow Rate: Maximum Pressure: 170 l/min (45 gpm) 241 bar (3500 psi) API 674 ATEX T100 Series medium pressure model with Stainless Steel pump head
More informationT100 Series Medium Pressure Models T100K & T100M
T100 Series Medium Pressure Models T100K & T100M Maximum Flow Rate: Maximum Pressure: 170 l/min (45 gpm) 1543 BPD 241 bar (3500 psi) API 674 ATEX T100 Series medium pressure model with Stainless Steel
More informationG03 Mono-Block Series
G03 Mono-Block Series Maximum Flow Rate: 11.7 l/min (3.1 gpm) Maximum Pressure: 103 bar (1500 psi) for Metallic Pump Heads ATEX Mono-Block (G03) Shaft-driven with Stainless Steel pump head Mono-Block (G03)
More informationDI PUMP PARTS PRICE LIST
ITEM 1 2 2A PUMP 5040 Pump Body, 1-1/2" NPT Mech. Seal 1 40058 1 5040 Pump Body, 1-1/2" NPT, Packing 1 40057 1 5040 Pump Body, 1-1/2" 150# Flg., Mech. Seal 1 40787 1 5040 Pump Body, 1-1/2" 150# Flg., Packing
More informationC Series Valves C24 1-1/4 NPT/BSPT C23 1 NPT/BSPT C22 3/4 NPT/BSPT. C22/C23/C24 Series (See page 88)
C Series Valves Accurate, repeatable Minimal pressure surge Smooth, chatter-free bypass Adjustable Easy to service No external springs or moving parts Various seal material Stainless steel or brass bodies
More information220-UL PUMP PARTS PRICE LIST
ITEM 1 PUMP Pump Body 1 See Note 1 1 Pump Body with Flush 1 See Note 1 1 7 Drive Shaft (Replaces 103227) 1 108425 8 Short Shaft (Replaces 103228) 1 108426 9 10 220-UL PUMP PARTS PRICE LIST DESCRIPTION
More informationPulsation Dampeners NEW! Wanner Engineering Inc
Pulsation Dampeners NEW! Wanner Engineering Inc Pulsation Dampeners Positive Displacement (PD) pumps create pulsation and hydraulic shock due to the reciprocating nature of their stroking action, potentially
More informationD15/D17 Series psi (172 bar) for Metallic Pump Heads
15/17 Series Maximum Flow Rate: Maximum Pressure: 15.5 gpm (58.7 l/min) 25 psi (172 bar) for Metallic Pump Heads 15/17 Series Performance Capacities Flow Pressure Model Max. Input rpm gpm l/min Max. Inlet
More informationModels 9202C, 9203C, 9252C-C, and 9253C-C
Models 0C, 03C, C-C, and 3C-C 3 0 3 consists of () Ref. O-ring, () Ref. Mechanical Seal (Viton) and () Ref. Gasket. NOTE: When ordering parts, give quantity, part number, decription, and complete model
More informationS Series PACER Pumps. PACER Pumps 5/91 Page 1 of 5. Dultmeier Sales for Omaha, NE or for Davenport, IA
PACER Pumps 5/91 Page 1 of 5 Item# Part No. Description Qty. 4 58-0721 NUT, BODY, Plated steel, 1/4-20 Hex... 10 58-0721 10 NUT, BODY, Stainless steel, 1/4-20 Hex... 10 6 58-0703 30 Bracket, polyester...
More informationValve Accessories NEW! Wanner Engineering Inc
Valve Accessories NEW! Wanner Engineering Inc Back Pressure Valves Diaphragm Back Pressure Valves enhance the performance of precision metering systems by applying a continuous back pressure to the EPM
More informationCondensed Catalog. Seal-less Pumps
Condensed Catalog Seal-less Pumps Hydra-Cell F/M/D/H Series Seal-less Pumps Hydra-Cell T and Q Series Pumps Hydra-Cell P Series Seal-less Metering Pumps Due to the Wanner Engineering Continuous Improvement
More informationU2 PUMP PARTS PRICE LIST
ITEM 1 7 8 9 PUMP 180-U2 Pump Body 1 See Note 1 1 180-U2 Pump Body with Flush 1 See Note 1 1 184-U2 Pump Body 1 See Note 1 1 184-U2 Pump Body with Flush 1 See Note 1 1 220-U2 Pump Body 1 See Note 1 1 220-U2
More informationU1 PUMP PARTS PRICE LIST
ITEM 1 7 8 9 PUMP 030-U1 Pump Body 1 See Note 1 1 030-U1 Pump Body with Flush 1 See Note 1 1 034-U1 Rectangular Flange Inlet Body 1 See Note 1 1 034-U1 Rect. Flange Inlet Body with Flush 1 See Note 1 1
More informationModels: G25, H25. Installation, Operation & Maintenance G C W0452
Installation, Operation & Maintenance G25-991-2400C Models: G25, H25 W0452 1204 Chestnut Avenue, Minneapolis, MN 55403 Tel: (612) 332-5681 Fax: (612) 332-6937 Toll-free fax [US only]: (800) 332-6812 www.hydra-cell.com/metering
More informationDI DI PUMP PARTS PRICE LIST
ITEM 1 2 2A 5050 Pump Body, 2" NPT Mech. Seal 1 40091 1 5050 Pump Body, 2" 150# RF Flg. Mech. Seal 1 40791 1 5050 Pump Body, 2" NPT, Packing 1 40088 1 5050 Pump Body, 2" 150# RF Flg., Packing 1 40793 1
More informationModels: D66. Installation, Operation & Maintenance A1
Installation, Operation & Maintenance 210-800A1 Models: D66 W0577A 1204 Chestnut Avenue, Minneapolis, MN 55403 Tel: (612) 332-5681 Fax: (612) 332-6937 Toll-free fax [US only]: (800) 332-6812 www.hydra-cell.com/metering
More informationSeal-less Pump Technology. Oil and Gas. Robust design - Reliability
Seal-less Pump Technology Oil and Gas Robust design - Reliability Hydra-Cell Oil & Gas Industry Pumps - High reliability, Gas Extraction Produced water injection Produced water disposal Well dewatering
More informationAuto Air Valve Parts List
Auto Air Valve Parts List 1 Cap 1 2 O Ring 1 3 Cover 1 4 Lock Nut 5/16 UNF 1 5 Flat Washer 8mm 2 6 Flat Washer 2 7 Diaphragm 1 8 Guide bush 1 9 O Ring 1 10 O Ring 1 11 Shaft 1 12 Flat Washer 1 13 Seat
More informationU1 PUMP PARTS PRICE LIST
006-014 - 015-018 - 024-U1 PUMP PARTS PRICE LIST ITEM 1 7 8 9 DESCRIPTION QTY. PER PART PUMP 006-U1 Pump Body 1 See Note 1 1 006-U1 Pump Body with Flush 1 See Note 1 1 015-U1 Pump Body 1 See Note 1 1 015-U1
More informationU1 PUMP PARTS PRICE LIST
ITEM 1 7 8 9 060-064 - 130-134 - 133-U1 PUMP PARTS PRICE LIST DESCRIPTION QTY. PER PUMP 060-U1 Pump Body 1 See Note 1 1 060-U1 Pump Body with Flush 1 See Note 1 1 064-U1 Rectangular Flange Inlet Body 1
More informationEXPLODED VIEW & PARTS LIST
SECTION 8 EXPLODED VIEW & PARTS LIST ALUMINUM, A300-*AA-****-*** 10 20 30 352 40 322 40 OPTIONAL 311 342 360 323 381 312 321 61 62 70 385 341 383 80 90 100 110 120 130 140 150 160 353 170 355 372 384 330
More informationPneumatic Chemical Metering Pump
Timberline s was designed with the well pumper and the chemical man in mind. Each pump has a simple but rugged design that can be repaired in the field within minutes on the tailgate of a pickup truck.
More informationModel SB1 1 /2-H Type 1
SERVICE AND OPERATING MANUAL Model SB1 1 /2-H Type 1 PLEASE NOTE! The photos shown in this manual are for general instruction only. Your specific model may not be shown. Always refer to the parts list
More informationMT8 Pump. Triplex Metering Pump with Pulse-Free Linear Flow
Maximum Flow Rate: Minimum Flow Rate: Maximum Pressure: 8.00 gph (30.28 lph) 0.06 gph (0.227 lph) 3500 psi (241 bar) MT8 with Stainless Steel pump head Hydra-Cell Metering Solutions pumps exceed API 675
More informationD 25 POLYPROPYLENE (BOLTED)
www.tablapump.com A COMPLETE RANGE OF AIR DIAPHRAGM PUMPS CONGRATULATIONS ON PURCHASING YOUR NEW TABLA PUMP! IMPORTANT: Please read all the installation and safety information carefully before you start
More informationWater and Waste Water Treatment
Seal-less Pump Technology Water and Waste Water Treatment Economy through Technology Hydra-Cell Water Treatment Pumps Compact, seal-less, Disinfection Sodium Hypochlorite Chlorine Dioxide Hydrogen Peroxide
More informationINDUSTRIAL PUMPS. Models: D-10, G-10 INSTALLATION & SERVICE WANNER ENGINEERING, INC.
INSTALLATION & SERVICE INDUSTRIAL PUMPS Models: D-10, G-10 WANNER ENGINEERING, INC. 1204 Chestnut Avenue, Minneapolis, MN 55403 TEL: (612) 332-5681 FAX: (612) 332-6937 TOLL-FREE FAX [US only]: (800) 332-6812
More informationD 40 ALUMINIUM (CLAMPED)
www.tablapump.com A COMPLETE RANGE OF AIR DIAPHRAGM PUMPS CONGRATULATIONS ON PURCHASING YOUR NEW TABLA PUMP! IMPORTANT: Please read all the installation and safety information carefully before you start
More informationHusky 515 / 716 Air-Operated Diaphragm Pumps
First choice when quality counts. Husky 515 / 716 Air-Operated Diaphragm Pumps 515 1/2 in. non-metallic pumps in acetal, polypropylene, and kynar 716 3/4 in. metal pumps in SST, aluminum No seals to leak
More informationINDUSTRIAL PUMPS INSTALLATION & SERVICE MODELS: D-12 G-12 WANNER ENGINEERING, INC.
INSTALLATION & SERVICE INDUSTRIAL PUMPS MODELS: D-12 G-12 WANNER ENGINEERING, INC. 1204 Chestnut Avenue, Minneapolis, MN 55403 TEL: (612) 332-5681 FAX: (612) 332-6937 TOLL-FREE FAX [US only]: (800) 332-6812
More informationMaintenance. Daily. Shutdown Procedure. Periodically. During Freezing Temperatures
Maintenance Daily Check the oil level and the condition of the oil. When the pump is operating, the oil in the pump housing gets warm and expands, filling into the oil reservoir. Depending on the type
More informationSST Series Sand Media Filtration Systems
SST Series Sand Media Filtration Systems Kits and Spare Parts Listing LS-695 (Rev. 6 / 07) Page 1 SST SAND FILTERS Installation Profile Automatic Systems WLS-594B(REV.11/03) Installation Configurations
More informationHydra-Cell T80 Series Pumps Design Advantages
Hydra-Cell T80 Series Pumps Design Advantages An Economical and Environmental Choice Hydra-Cell is a positive displacement, multiple-diaphragm pump featuring a seal-less design that provides full containment
More informationD/G-03 Maintenance. Shutdown Procedure During Freezing Temperatures. Daily. Periodically
D/G-03 Maintenance NOTE: The numbers in parentheses are the Ref. Nos. on the illustrations in the Parts Manual. Daily Check the oil level and the condition of the oil. The oil level should be 3/4 in. (20
More informationSelection Guide for P Series Pump Accessories & Options
Selection Guide for P Series Pump Accessories & Options Contents Page Calibration Cylinders...2 Back Pressure & Pressure Relief Valves...3 Pulsation Dampeners...6 Motors & Controllers...9 Calibration Cylinders
More informationH25 Series. Maximum Flow Rate: 20.0 gpm (75.9 l/min) Maximum Pressure: 1000 psi (69 bar) for Metallic Pump Heads
25 Series Maximum Flow Rate: 2. gpm (75.9 l/min) Maximum Pressure: 1 psi (69 bar) for Metallic Pump eads 25 Series Performance apacities Max. Max. Flow Input @ 1 psi (69 bar) Model rpm gpm l/min 25-115
More informationWe put the work in work trucks. Termite Control. Manufactured for Terminix
Termite Control Manufactured for Terminix WWW.AUTOTRUCK.COM ORDERING To order parts, please call our toll-free Parts Department number: 877-284-4440 To expedite your order, please have the following information
More informationModels: D-04, G-04 INSTALLATION & SERVICE D A WANNER ENGINEERING, INC.
INSTALLATION & SERVICE D04-991-2400A Models: D-04, G-04 W0069A WANNER ENGINEERING, INC. 1204 Chestnut Avenue, Minneapolis, MN 55403 TEL: (612) 332-5681 FAX: (612) 332-6937 TOLL-FREE FAX [US only]: (800)
More informationF-20/G-20 Maintenance
F-20/G-20 Maintenance NOTE: The numbers in parentheses are the Ref. Nos. on the illustrations in the Parts Manual. Periodically Change the oil after the first 100 hours of operation, and every 1000 operating
More informationParts Lists UII Pump Parts
Parts Lists Parts Lists Waukesha Cherry-Burrell 006-04-05-08-UII Pump Parts Page 48 95-0305 September 009 006-04-05-08-UII Pump Parts PART NOTES 006-U Pump Body See Note 006-U Pump Body with Flush See
More informationSD Series. Slurry Duty Pumps. sd - Slurry duty hydra-cell diaphragm pump
sd - Slurry duty hydra-cell diaphragm pump SD Series Slurry Duty Pumps Hydra-Cell Slurry Duty pumps are specifically designed for abrasive duty applications in order to: Increase flow Reduce and simplify
More informationD/G-10 Maintenance. Daily. Shutdown Procedure During Freezing Temperatures. Periodically
D/G-10 Maintenance NOTE: The numbers in parentheses are the Reference Numbers on the exploded view illustrations found in this manual and in the Parts Manual. Daily Check oil level and condition of oil.
More informationUII Pump Parts
Parts Lists 030-034-040-UII Pump Parts Waukesha Cherry-Burrell. Page 54 95-03015 September 2009 030-034-040-UII Pump Parts 1 7 8 9 10 : 1. 2. 12. 12A. 13. PART 030-U2 Pump Body 1 See Note 1 1 030-U2 Pump
More information