Standard cylinders DNC, ISO 15552

Transcription

1

2 Key features At a glance DIN Standards-based cylinders to ISO15552 (corresponds to the withdrawn standards ISO 6431, DIN ISO 6431, VDMA24562, NFE and UNI 10290) The modern design and construction save up to 11% on fitting space compared to ordinary standard cylinders, thus permitting a considerably more compact system design An extensive range of accessories makes it possible to install the cylinder virtually anywhere The widest range of variants on the market provides the right DNC cylinder for every application Cylinder with clamping units DNC-KP DNCKE Piston rod can be held or clamped in any position Piston rod can be held in position for long periods even with alternating loads, fluctuating operating pressure or leaks in the system Suitable for use in safety-related control systems in compliance with EN 954-1, EN 1050, EN 292 and EN 983 Fail-safe Piston rod can be clamped in any position Cylinder with end-position locking DNC- -EL Cylinder/valve combination DNC-V1 V6 Mechanical locking when the end position is reached Lock is only automatically released when pressure is supplied to the cylinder End-position locking at one or both ends The cylinder/valve combination is assembled and fitted with tubing ready for connection Particularly suitable for decentralised use in larger systems Tandem cylinder DNCT Connection of 2 cylinders with the same piston diameter and stroke in series Double the thrust and return force in comparison to a standard cylinder Longer service life thanks to the bellows kit DADB 1 The bellows protects the piston rod, the seal and the bearing from the effects of a wide range of media, which has a positive impact on the service life of these components. The bellows kit is a leak-free system. To prevent unwanted media being drawn in, the supply and exhaust air must be ducted via a pressure compensation hole in the connection part 1. The kit protects the piston rod, seal and bearings from a wide range of media, for example: dust, chips, oil, grease, fuel. 2 Internet: Subject to change 2017/11

3 Key features Variants from the modular product system Symbol Key features Description S2 Through piston rod For working at both ends with the same force in the forward and return stroke, for attaching external stops S6 Heat-resistant seals Temperature resistance up to max. 120 C S10 Constant motion (slow speed) at low piston speeds Suitable for slow stroke movements at a constant, stick-slip-free speed over the full stroke of the cylinder. Seal contains silicone grease (not free of paint-wetting impairment substances) S11 Low friction Special seals considerably reduce system wear. This means a considerably lower response pressure. Seal contains silicone grease (not free of paint-wetting impairment substances) S20 Through, hollow piston rod For supplying vacuum, small parts, media, etc. K2 Extended male piston rod thread K3 Female piston rod thread K5 Special piston rod thread Metric standard thread to ISO K7 Piston rod with external hexagon Special spanner flats K8 Extended piston rod K10 Smooth anodised aluminium piston rod Ideal for use in welding environments: Protection against welding spatter Small working loads Harder surface compared to steel Long service life KP With clamping unit Integrated clamping unit on the piston rod EL With end-position locking Positive locking in the end position as a drop guard. If there is a drop in pressure, the piston rod is secured in its end position to prevent it from dropping Q Square piston rod Protection against rotation. For correctly oriented feeding ÓÓÓÓÓÓ R3 High corrosion protection All external cylinder surfaces comply with corrosion resistance class 3 to Festo standard The piston rod is made from corrosion and acid-resistant steel R8 Dust protection (wiper seal) The cylinder is equipped with a hard-chrome plated piston rod and a rigid wiper seal, which protects against dry, dusty media Software tools Configuration of Festo modular products /11 Subject to change Internet: 3

4 Product range overview Function Design Type Piston Stroke Position sensing Protection against rotation Through/hollow piston rod Extended male piston rod thread Female piston rod thread Special piston rod thread [mm] [mm] A Q S2/S20 K2 K3 K5 Doubleacting Basic version DNC 32, 40, 50, 63, 80, 100, , 25, 30, 40, 50, 60, 70, 80, 100, 125, 150, 160, 200, 250, 300, 320, 400, Standard hole pattern, with clamping unit DNC-KP 32, 40, , 63, 80, 100, 125 DNCKE 40, 63, S2 Standard hole pattern, with end-position locking DNC- -EL 32, 40, , 63, 80, 100 S2 Standard hole pattern, cylinder/valve combination DNC-V1 V6 32, 40, , 63, 80, 100 Standard hole pattern, tandem cylinder DNCT 32, 40, , 80, , Internet: Subject to change 2017/11

5 Product range overview Type Page/Internet Special spanner flats Extended piston rod Smooth anodised piston rod Heat-resistant seals to max. 120 C Slow speed (constant motion) Low friction High corrosion protection Dust protection Cylinder/valve combination Basic version DNC K7 K8 K10 S6 S10 S11 R3 R8 V1 V6 9 Standard hole pattern, with clamping unit DNC-KP 25 DNCKE 2 Standard hole pattern, with end-position locking DNC- -EL 33 Standard hole pattern, cylinder/valve combination DNC-V1 V6 40 Standard hole pattern, tandem cylinder DNCT /11 Subject to change Internet: 5

6 Peripherals overview aj 9 6 bi bg bh 9 aa ab ac ad aa ab 5 af ae bf ag ai ah bj be aj ba bb 2 bd DNC- -S2 bc Mounting attachments and accessories Description DNC Page/ Basic version KP EL V1 V6 Internet 1 Multi-position kit DPNC 2 Foot mounting HNC/CRHNC 3 Flange mounting FNC/CRFNG 4 Trunnion flange ZNCF/CRZNG 5 Trunnion support LNZG/CRLNZG 6 Swivel flange SNC 7 Clevis foot LSNG 8 Clevis foot LSNSG For connecting two cylinders with identical piston diameters to form a multi-position cylinder For bearing or end caps For bearing or end caps Cannot be used on the bearing cap in combination with bellows kit DADB For bearing or end caps Cannot be used on the bearing cap in combination with bellows kit DADB For end caps With spherical bearing Weld-on, with spherical bearing 1) 1) ) 1) 1) 55 1) 1) 1) 59 1) 1) 1) 59 6 Internet: Subject to change 2017/11

7 Peripherals overview Mounting attachments and accessories Description DNC Page/ Basic version KP EL V1 V6 Internet 9 Swivel flange SNCS/CRNCS/SNCS- -R3 aj Clevis foot LBG/LBG- -R3 aa Swivel flange SNCL ab Swivel flange SNCB/SNCB- -R3 ac Clevis foot LNG/CRLNG ad Clevis foot LSN ae Trunnion mounting kit DAMT af Rod eye SGS/CRSGS ag Right-angle clevis foot LQG ah Rod clevis SGA ai Coupling piece KSG Coupling piece KSZ bj Rod clevis SG/CRSG ba Self-aligning rod coupler FK/CRFK bb Adapter AD bc Guide unit FENG bd be bf bg bh bi Mounting kit SMB-8-FENG Slot cover ABP-5-S Proximity sensor SME/SMT-8 One-way flow control valve GRLA Push-in fitting QS Bellows kit DADB With spherical bearing for end caps For end caps For end caps With spherical bearing For mounting anywhere along the cylinder profile barrel With spherical bearing With male thread To compensate for radial deviations For cylinders with a non-rotating piston rod to compensate for radial deviations Permits a swivelling movement of the cylinder in one plane For compensating radial and angular deviations For fitting a suction cup on a hollow cylinder piston rod For protecting standard cylinders against rotation at high torque loads 1) 1) 1) 57 1) 1) 59 1) 1) 1) 57 1) 1) 1) 56 1) 1) 1) 59 1) 1) 1) and above For attaching proximity sensor SMT-8 to cylinders in combination with guide unit FENG 2) 50 and above For protecting the sensor cables and keeping dirt out of the sensor slots Can be integrated in the cylinder profile barrel For regulating speed For connecting compressed air tubing with standard outside diameter Protects the cylinder (piston rod, seal and bearings) against a wide range of media and thus prevents premature wear The kit can only be used in combination with an extended piston rod (K8) qs 61 1) Not with variant S2 or S20 2) For piston 32, 40 mm only with variant R3 2017/11 Subject to change Internet: 7

8 Type codes u DNC PPV A Type Double-acting DNC Standard cylinder Piston [mm] Stroke [mm] Cushioning P PPV Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Position sensing A Without position sensing Via proximity sensor -H- Note The standard cylinder DNC can be ordered using either a fixed part number and type designation or via the modular product system. The type code listed above only applies to the DNC standard cylinder with fixed part number and type designation. Variants can only be ordered using the modular product system. 8 Internet: Subject to change 2017/11

9 Technical data Function DNC- Without position sensing -N- Diameter mm -T- Stroke length mm -W- DNC- -A- With position sensing Wearing parts kits page 24 Standards-based cylinders to ISO15552 (corresponds to the withdrawn standards ISO 6431, DIN ISO 6431, VDMA24562, NFE and UNI 10290) DIN General technical data Piston Pneumatic connection G1/8 G1/4 G1/4 G3/8 G3/8 G1/2 G1/2 Piston rod thread M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5 M27x2 K3 M6 M8 M10 M10 M12 M12 M16 K5 M10 M12 M16 M16 M20 M20 M27 Constructional design Piston Piston rod Profile barrel Max. torsional backlash of piston rod [ ] Q ±0.65 ±0.6 ±0.45 ±0.45 ±0.45 ±0.45 Cushioning Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Cushioning length PPV [mm] Position sensing Via proximity sensor Type of mounting Via female thread Via accessories Mounting position Any -H- Note: This product conforms to ISO and to ISO /11 Subject to change Internet: 9

10 Technical data Operating and environmental conditions Piston Operating medium Compressed air in accordance with ISO :2010 [7:4:4] Note on operating/pilot medium Operation with lubricated medium possible (in which case lubricated operation will always be required) Operating pressure [bar] Ambient temperature 1) [ C] R S11 After 10 strokes After 24 hours S Corrosion resistance class 2 CRC 2) R3 3 Maritime classification 3) See certificate ATEX Specified types 1) Note operating range of proximity sensors 2) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Corrosion resistance class CRC 3 to Festo standard FN High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial environment. 3) Additional information Certificates. Force [N] and impact energy [J] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting S2/S S2/S Max. impact energy at the end positions 1) 1) The permissible impact energy is reduced by approx. 10% for variants K10 and S20 Permissible impact velocity: Maximum permissible load: 2xE perm. v perm. mdead m load m load 2xE perm. v 2 m dead v perm. Permissible impact velocity E perm. Max. impact energy m Intrinsic Moving load (drive) m Load Moving effective load -H- Note This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed. 10 Internet: Subject to change 2017/11

11 Technical data Lateral force Fq as a function of stroke length l Basic version Fq /63 80/ /11 Subject to change Internet: 11

12 Technical data Lateral force Fq as a function of stroke length l and lever arm s Q Square piston rod Max. torque = 800 Nmm / Max. stroke = 300 mm Max. torque = 1100 Nmm / Max. stroke = 400 mm s [mm] Fq [N] s [mm] Fq [N] l [mm] l [mm] 50/63 80/100 Max. torque = 1500 Nmm / Max. stroke = 500 mm Max. torque = 3000 Nmm / Max. stroke = 600 mm s [mm] Fq [N] s [mm] Fq [N] l [mm] l [mm] Examples for piston 32 mm Example 1: Stroke length l = 150 mm Result: permissible Lateral force Fq = 9.5 N Lever arm s = 84 mm Example 2: Lateral force Fq = 40 N Result: permissible Stroke length l = 28 mm Lever arm s = 20 mm Example 3: Stroke length l = 150 mm Lever arm s = 100 mm Max. torque 800 Nmm Fq = Lever arm 100 mm = 8 N Result: permissible Fq = 8 N Fq max. = 9.5 N Fq 12 Internet: Subject to change 2017/11

13 Technical data Weight [g] Piston Basic version Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke Q Square piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke S2 Through piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke K10 Smooth anodised piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke S2-K10 Through, smooth anodised piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load with 0 mm stroke Additional load per 10 mm stroke /11 Subject to change Internet: 13

14 Technical data Materials Sectional view Standard cylinder Basic version K10 R3 1 Profile barrel Wrought aluminium alloy, smooth anodised 2 Bearing and end caps Die-cast aluminium 3 Piston rod High-alloy steel Wrought aluminium alloy, anodised High-alloy stainless steel Seals Polyurethane, nitrile rubber Note on materials RoHS compliant Standard cylinder R8 S6 S10 S11 1 Profile barrel Wrought aluminium alloy, smooth anodised 2 Bearing and end caps Die-cast aluminium 3 Piston rod Tempered steel, High-alloy steel hard-chromium plated Seals Polyurethane, nitrile rubber Fluoro rubber Note on materials RoHS compliant Contains PWIS (paint-wetting impairment substances) 14 Internet: Subject to change 2017/11

15 Technical data Dimensions Basic version Download CAD data 1 For mounting attachments: : Socket head screw with female thread 125: Thread in the end cap 2 Regulating screw for adjustable end-position cushioning 3 Slot for proximity sensor SME/SMT-8 + = plus stroke length AM B BG E EE J2 J3 KK L1 L2 [mm] d G1/ M10x G1/4 8 6 M12x G1/ M16x G3/ M16x G3/ M20x G1/ M20x G1/ M27x L7 MM [mm] PL RT TG VA VD WH ZJ ß1 ß2 ß M M M M M M M H- Note: This product conforms to ISO and to ISO /11 Subject to change Internet: 15

16 Technical data Dimensions Variants Q Square piston rod Download CAD data S2 Through piston rod + = plus stroke length ++ = plus 2x stroke length S20 Through hollow piston rod + = plus stroke length ++ = plus 2x stroke length B1 D8 ZJ ZM [mm] ) ) Internal narrowing to 5.5 mm 2) Internal narrowing to 10.2 mm 16 Internet: Subject to change 2017/11

17 Technical data Dimensions Variants K2 Extended male piston rod thread K3 Female piston rod thread Download CAD data K5 Special piston rod thread K7 Piston rod with external hexagon K8 Extended piston rod -H- Note In combination with variant S2/S20, the piston rod is extended at one end. In combination with variant Q, the square piston rod is extended. A1 A2 AF AM KF KK T4 WH ß1 max. max. Basic thread Special [mm] thread 1) M6 M10x1.25 M M8 M12x1.25 M M10 M16x1.5 M M10 M16x1.5 M M12 M20x1.5 M M12 M20x1.5 M M16 M27x2 M ) The special threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery 2017/11 Subject to change Internet: 17

18 Technical data Ordering data Without position sensing Piston Stroke Part No. Type 1) Piston Stroke Part No. Type 1) [mm] [mm] [mm] [mm] DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV DNC PPV 1) The mounting nut on the piston rod thread is included in the scope of delivery 18 Internet: Subject to change 2017/11

19 Technical data Ordering data With position sensing Piston Stroke Part No. Type 1) Piston Stroke Part No. Type 1) [mm] [mm] [mm] [mm] DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A 1) The mounting nut on the piston rod thread is included in the scope of delivery 2017/11 Subject to change Internet: 19

20 Technical data Ordering data With position sensing Piston Stroke Part No. Type 1) [mm] [mm] DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A DNC PPV-A 1) The mounting nut on the piston rod thread is included in the scope of delivery 20 Internet: Subject to change 2017/11

21 Technical data Ordering data Variable stroke Piston Stroke Without position sensing [mm] [mm] Part No. Type 1) DNC-32- -PPV DNC-40- -PPV DNC-50- -PPV DNC-63- -PPV DNC-80- -PPV DNC PPV DNC PPV 1) The mounting nut on the piston rod thread is included in the scope of delivery Ordering data Variable stroke Piston Stroke With position sensing [mm] [mm] Part No. Type 1) DNC-32- -PPV-A DNC-40- -PPV-A DNC-50- -PPV-A DNC-63- -PPV-A DNC-80- -PPV-A DNC PPV-A DNC PPV-A 1) The mounting nut on the piston rod thread is included in the scope of delivery 2017/11 Subject to change Internet: 21

22 Ordering data Modular products Ordering table Size Conditions 0M Module No Function Standard cylinder, double-acting, based on ISO DNC DNC Piston [mm] Stroke [mm] Cushioning Flexible cushioning rings/pads at both ends -P Pneumatic cushioning, adjustable at both ends ae -PPV 0O Position sensing Via proximity sensor -A Protection against rotation Square piston rod 2 -Q Type of piston rod Through piston rod 3 -S2 Through, hollow piston rod 4 -S20 Extended male thread Piston rod with extended male thread [mm] K2 Female thread Piston rod with female thread (M6) (M8) (M10) (M10) (M12) (M12) (M16) 6 -K3 Special thread Piston rod with special thread M10 M12 M16 M16 M20 M20 M K5 Code Enter code ae PPV For piston 125 not with S11 2 Q Max. stroke: mm. In combination with S2: square piston rod at bearing cap end only. Not with S20, K7, K10, S10, S11, R8 3 S2 In combination with K2: thread extended at both ends. In combination with K3: female thread at both ends. In combination with K5: special thread at both ends. In combination with K8: piston rod extended at bearing cap end only. Not with K7, S10, S11 4 S20 Max. stroke: 850 mm. Not with K2, K3, K5, K8, K10, S6, S10, S11, R8 5 K2 Not with K3, K10 6 K3 With K5: on request. Not with K7 7 K5 Not with K10 Transfer order code DNC 22 Internet: Subject to change 2017/11

23 Ordering data Modular products Ordering table Size Conditions Code Special spanner flats Piston rod with external hexagon 8 -K7 0O Extended piston rod Extended piston rod [mm] K8 Improved running performance Smooth anodised aluminium coated piston rod 9 -K10 Temperature resistance Heat-resistant seals for temperatures up to 120 C aj -S6 Slow speed (constant motion) Slow speed (constant motion at low piston speeds) ab -S10 Running characteristics Low friction ac -S11 Corrosion protection High corrosion protection ad -R3 Wiper seal Dust protection -R8 Enter code 8 K7 Not with Q, S2, K10 9 K10 Max. stroke: 1,000 mm. Not with S6, R3, R8 aj S6 Not with S10, S11, R8 ab S10 Max. stroke: 500 mm; additional strokes on request. Not with S11, R3, R8 ac S11 Max. stroke: 500 mm; additional strokes on request. Not with R3, R8 ad CT, R3 Not with R8 Transfer order code 2017/11 Subject to change Internet: 23

24 Ordering data Wearing parts kits Part No. Type Part No. Type Piston Basic version S6 Heat-resistant seals up to max. 120 C DNC-32- -PPV-(A) DNC-32- -PPV-(A)-S DNC-40- -PPV-(A) DNC-40- -PPV-(A)-S DNC-50- -PPV-(A) DNC-50- -PPV-(A)-S DNC-63- -PPV-(A) DNC-63- -PPV-(A)-S DNC-80- -PPV-(A) DNC-80- -PPV-(A)-S DNC PPV-(A) DNC PPV-(A)-S DNC PPV-(A) DNC PPV-(A)-S6 24 Internet: Subject to change 2017/11

25 Standard cylinders DNC-KP, standard hole pattern, with clamping unit Technical data Function DNC- -KP Without position sensing -N- Diameter mm -T- Stroke length mm -W- DNC- -A- -KP With position sensing Wearing parts kits page 32 -H- Note Additional measures are required for use in safety-related applications; in Europe, for example, the standards listed under the EC Machinery Directive must be observed. Without additional measures in accordance with statutory minimum requirements, the product is not suitable for use in safety-related sections of control systems. General technical data Piston Pneumatic connection Cylinder G1/8 G1/4 G1/4 G3/8 G3/8 G1/2 G1/2 KP M5 G1/8 G1/8 G1/8 G1/8 G1/8 G1/8 Piston rod thread M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5 M27x2 K3 M6 M8 M10 M10 M12 M12 M16 K5 M10 M12 M16 M16 M20 M20 M27 Axial play under load [mm] Constructional design Piston Piston rod Profile barrel Clamping unit Cushioning Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Cushioning length PPV [mm] Position sensing Via proximity sensor Type of mounting Via female thread Via accessories Mounting position Any Clamping type with effective direction At both ends -H- Note: This product conforms to ISO and to ISO Operating and environmental conditions Operating medium Compressed air in accordance with ISO :2010 [7:4:4] Note on operating/pilot medium Operation with lubricated medium possible (in which case lubricated operation will always be required) Operating pressure [bar] Min. release pressure [bar] 3 Ambient temperature 1) [ C] Corrosion resistance class CRC 2) 2 Maritime classification 3) See certificate 1) Note operating range of proximity sensors 2) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. 3) Additional information Certificates. 2017/11 Subject to change Internet: 25

26 Standard cylinders DNC-KP, standard hole pattern, with clamping unit Technical data Impact energy [J] Piston Max. impact energy at the end positions Permissible impact velocity: Maximum permissible load: 2xE perm. v perm. mdead m load m load 2xE perm. v 2 m dead v perm. Permissible impact velocity E perm. Max. impact energy m Intrinsic Moving load (drive) m Load Moving effective load -H- Note This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed. Forces [N] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting S S Static holding force H- Note The specified holding force refers to a static load. If this value is exceeded, slippage may occur. Dynamic forces occurring during operation must not exceed the static holding force. The clamping unit is not backlash-free in the clamped condition if varying loads are applied to the piston rod. Activation: The clamping unit may only be released if the forces at the piston have reached equilibrium. Otherwise, there is a risk of accidents due to sudden movement of the piston rod. Blocking off the air supply at both ends (e.g. with a 5/3-way valve) does not provide any safety. 26 Internet: Subject to change 2017/11

27 Standard cylinders DNC-KP, standard hole pattern, with clamping unit Technical data Max. lateral force Fq as a function of stroke length l Fq /63 80/ Materials Sectional view Standard cylinder 1 Profile barrel Wrought aluminium alloy, smooth anodised 2 Bearing and end caps Die-cast aluminium 3 Piston rod High-alloy steel 4 Housing, clamping unit Wrought aluminium alloy, anodised 5 Clamping jaws Brass 6 Spring Spring steel 7 Piston Polyacetal Seals Polyurethane, nitrile rubber Note on materials RoHS compliant 2017/11 Subject to change Internet: 27

28 Standard cylinders DNC-KP, standard hole pattern, with clamping unit Technical data Dimensions Basic version Download CAD data 1 For mounting attachments: : Socket head screw with female thread 125: Thread in the end cap 2 Regulating screw for adjustable end-position cushioning 3 Slot for proximity sensor SME/SMT-8 + = plus stroke length [mm] AM B d11 BG D1 f9 D2 E EE H1 J2 J3 KK L2 L M5 45 G1/ M10x G1/8 54 G1/ M12x G1/8 64 G1/ M16x G1/8 75 G3/ M16x G1/8 93 G3/ M20x G1/8 110 G1/ M20x G1/8 134 G1/ M27x [mm] L5 L7 MM PL RT TG VA VD WH ZJ ß1 ß2 ß M M M M M M M H- Note: This product conforms to ISO and to ISO H- Note The dimensions for the cylinder/ valve combination are on page page Internet: Subject to change 2017/11

29 Standard cylinders DNC-KP, standard hole pattern, with clamping unit Technical data Dimensions Variants Q Square piston rod Download CAD data -H- Note Clamping unit and variant Q only in combination with S2. S2 Through piston rod + = plus stroke length ++ = plus 2x stroke length -H- Note The thread types at both piston rod ends are identical. In combination with variant Q, the left-hand piston rod is round, the right-hand piston rod square. The clamping unit is mounted on the left-hand, round piston rod. K2 Extended male piston rod thread K3 Female piston rod thread K5 Special piston rod thread K7 Piston rod with external hexagon K8 Extended piston rod -H- Note In combination with variant S2, the piston rod is extended at one end. The clamping unit is mounted on the side of the piston rod that is not extended. If variant Q is also required, the extension will only be added to the square piston rod. A1 A2 AF AM B1 KF KK T4 WH ZJ ZM ß1 [mm] max. max. Basic thread Special thread 1) M6 M10x1.25 M M8 M12x1.25 M M10 M16x1.5 M M10 M16x1.5 M M12 M20x1.5 M M12 M20x1.5 M M16 M27x2 M ) The special threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery 2017/11 Subject to change Internet: 29

30 Standard cylinders DNC-KP, standard hole pattern, with clamping unit Ordering data Modular products Ordering table Size Conditions 0M Module No Function Standard cylinder, double-acting, standard hole pattern, with clamping unit DNC DNC Piston [mm] Stroke [mm] Cushioning Flexible cushioning rings/pads at both ends -P Pneumatic cushioning, adjustable at both ends -PPV 0O Position sensing Via proximity sensor -A Protection against rotation Square piston rod 1 -Q Type of piston rod Through piston rod 2 -S2 Code Enter code 1 Q Max. stroke: mm In combination with S2: square piston rod at bearing cap end only In combination with KP: only supplied with S2 Not with K7 2 S2 In combination with K2: extended thread at both ends In combination with K3: female thread at both ends In combination with K5: special thread at both ends In combination with K8: piston rod extended at bearing cap end only In combination with KP: clamping unit at end cap Not with K7 Transfer order code DNC 30 Internet: Subject to change 2017/11

31 Standard cylinders DNC-KP, standard hole pattern, with clamping unit Ordering data Modular products Ordering table Size Conditions Code Enter code Extended male thread Piston rod with extended male thread 0O [mm] K2 Female thread Piston rod with female thread (M6) (M8) (M10) (M10) (M12) (M12) (M16) 4 -K3 Special thread Piston rod with special thread M10 M12 M16 M16 M20 M20 M27 - K5 Special spanner flats Piston rod with external hexagon -K7 Extended piston rod Extended piston rod [mm] K8 0M Clamping unit Attached 5 -KP -KP 0O Cylinder/valve combination Single solenoid valve, fitted on right, piston rod retracted when unactuated 6 -V1 Single solenoid valve, fitted on right, piston rod advanced when unactuated 6 -V2 Double solenoid valve, fitted on right 6 -V3 Single solenoid valve, fitted on left, piston rod retracted when unactuated 6 -V4 Single solenoid valve, fitted on left, piston rod advanced when unactuated 6 -V5 Double solenoid valve, fitted on left 6 -V6 3 K2 Not with K3 4 K3 With K5: on request Not with K7 5 KP Without S2: position of the clamping unit at the bearing cap 6 V Min. stroke: 100 mm Transfer order code KP 2017/11 Subject to change Internet: 31

32 Standard cylinders DNC-KP, standard hole pattern, with clamping unit Ordering data Wearing parts kits Part No. Type Piston Basic version DNC-32- -PPV-(A) DNC-40- -PPV-(A) DNC-50- -PPV-(A) DNC-63- -PPV-(A) DNC-80- -PPV-(A) DNC PPV-(A) DNC PPV-(A) 32 Internet: Subject to change 2017/11

33 Standard cylinders DNC-EL, standard hole pattern, with end-position locking Technical data Function DNC- -A- -EL With position sensing -W- Wearing parts kits page 24 -N- Diameter mm -T- Stroke length mm -H- Note Additional measures are required for use in safety-related applications; in Europe, for example, the standards listed under the EC Machinery Directive must be observed. Without additional measures in accordance with statutory minimum requirements, the product is not suitable for use in safety-related sections of control systems. General technical data Piston Pneumatic connection G1/8 G1/4 G1/4 G3/8 G3/8 G1/2 Piston rod thread M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5 Max. axial backlash with [mm] end position locked Constructional design Piston Piston rod Profile barrel End-position locking ELB At both ends ELV At front ELH At rear Cushioning Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Cushioning length PPV [mm] Position sensing Type of mounting Mounting position EL Via proximity sensor Via female thread Via accessories Any -H- Note: This product conforms to ISO and to ISO H- Note End-position locking should only be operated in conjunction with double-acting cylinders with exhaust air flow control in order to ensure that the lock is always completely released prior to starting the drive movement. No screws with a head or similar may be used in place of endposition locking, as there is a risk that the function will be impaired if they are screwed in too deeply. The exhaust hole must not be closed. Locking can be performed from any stroke position once the drive is brought mechanically into its end position. End-position locking has been designed to prevent the load dropping in case of pressure failure. An excessive end-position cushioning setting (more than 50% closed) can result in the locking bolt not engaging reliably, resulting in premature wear. 2017/11 Subject to change Internet: 33

34 Standard cylinders DNC-EL, standard hole pattern, with end-position locking Technical data Operating and environmental conditions Piston Operating medium Compressed air in accordance with ISO :2010 [7:4:4] Note on operating/pilot medium Operation with lubricated medium possible (in which case lubricated operation will always be required) Operating pressure [bar] Ambient temperature 1) [ C] Corrosion resistance class CRC 2) 2 Maritime classification 3) See certificate 1) Note operating range of proximity sensors 2) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. 3) Additional information Certificates. Impact energy [J] Piston Max. impact energy at the end positions Permissible impact velocity: Maximum permissible load: 2xE perm. v perm. mdead m load m load 2xE perm. v 2 m dead v perm. Permissible impact velocity E perm. Max. impact energy m Intrinsic Moving load (drive) m Load Moving effective load -H- Note This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed. Forces [N] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting Static holding force Sizing example -H- Note When sizing pneumatic cylinders it is recommended as a basic principle that only 50% of the indicated theoretical forces (see above) be used. Given: Installation position = Vertical Workpiece load = 44 kg F = m x g = 44 kg x 9.81 m/s 2 = N To be calculated: Suitable piston Example with 32 mm piston : Theoretical force at 6 bar, advancing = 483 N 50% of the theoretical force = N Static holding force with 32 mm piston = 500 N The static holding force of end-position locking is within the permissible range (max. 500 N) with a workpiece load of 44 kg (431.6 N), however the cylinder would be at 89% capacity. Result: A cylinder with a piston of 40 mm is therefore recommended for this application. 34 Internet: Subject to change 2017/11

35 Standard cylinders DNC-EL, standard hole pattern, with end-position locking Technical data Max. lateral force Fq as a function of stroke length l Fq /63 80/100 Weight [g] Piston Basic version Product weight with 0 mm stroke Additional weight per 10 mm stroke S2 Through piston rod Product weight with 0 mm stroke Additional weight per 10 mm stroke Materials Sectional view Standard cylinder 1 Profile barrel Wrought aluminium alloy, smooth anodised 2 Bearing and end caps Die-cast aluminium 3 Piston rod High-alloy steel Seals Polyurethane, nitrile rubber Note on materials RoHS compliant 2017/11 Subject to change Internet: 35

36 Standard cylinders DNC-EL, standard hole pattern, with end-position locking Technical data Dimensions Basic version Download CAD data 1 Socket head screw with female thread for mounting attachments 2 Regulating screw for adjustable end-position cushioning 3 Slot for proximity sensor + = plus stroke length Dimensions Variants S2 Through piston rod Download CAD data + = plus stroke length ++ = plus 2x stroke length [mm] AM B d11 BG D1 f8 D2 E EE G H1 H2 J1 J2 J3 KK L M3 45 G1/ M10x M3 54 G1/ M12x M5 64 G1/ M16x M5 75 G3/ M16x M5 93 G3/ M20x M5 110 G1/ M20x L2 L3 L4 L7 MM PL RT TG VA VD WH ZM ZJ ß1 ß2 ß3 [mm] ± M M M M M M H- Note: This product conforms to ISO and to ISO Internet: Subject to change 2017/11

37 Standard cylinders DNC-EL, standard hole pattern, with end-position locking Technical data Dimensions Variants K2 Extended male piston rod thread Download CAD data K3 Female piston rod thread K5 Special piston rod thread K8 Extended piston rod -H- Note In combination with variant S2, the piston rod is extended at one end. A1 A2 AF AM KF KK T4 WH ß1 max. max. Basic thread Special [mm] thread 1) M6 M10x1.25 M M8 M12x1.25 M M10 M16x1.5 M M10 M16x1.5 M M12 M20x1.5 M M12 M20x1.5 M ) The special threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery 2017/11 Subject to change Internet: 37

38 Standard cylinders DNC-EL, standard hole pattern, with end-position locking Ordering data Modular products Ordering table Size Conditions 0M Module No Function Standard cylinder, double-acting, standard hole pattern, with end-position locking DNC DNC Piston [mm] Stroke [mm] Cushioning Flexible cushioning rings/pads at both ends -P Pneumatic cushioning, adjustable at both ends -PPV 0O Position sensing Via proximity sensor -A Type of piston rod Through piston rod 1 -S2 Code Enter code 1 S2 In combination with K2: extended thread at both ends In combination with K3: female thread at both ends In combination with K5: special thread at both ends Transfer order code DNC 38 Internet: Subject to change 2017/11

39 Standard cylinders DNC-EL, standard hole pattern, with end-position locking Ordering data Modular products Ordering table Size Conditions Code Enter code Extended male thread Piston rod with extended male thread 0O [mm] K2 Female thread Piston rod with female thread (M6) (M8) (M10) (M10) (M12) (M12) 3 -K3 Special thread Piston rod with special thread M10 M12 M16 M16 M20 M20 - K5 Extended piston rod Extended piston rod [mm] K8 0M End-position locking At both ends 4 -ELB At front 4 -ELV At rear 4 -ELH 2 K2 Not with K3 3 K3 With K5: on request 4 ELB, ELV, ELH In combination with K8 and S2: on request only Transfer order code 2017/11 Subject to change Internet: 39

40 Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combination Technical data Function DNC- Without position sensing -N- Diameter mm -T- Stroke length mm -W- DNC- -A- With position sensing Wearing parts kits page 32 Valve variants Single solenoid valve unactuated, piston rod retracted Double solenoid valve unactuated, piston rod retracted DNC- -V1 fitted on right DNC- -V3 fitted on right DNC- -V4 fitted on left DNC- -V6 fitted on left Single solenoid valve unactuated, piston rod advanced DNC- -V2 fitted on right -H- Note As viewed from the front of the cylinder (piston rod end) with valve fitted on left or right. In this example, the valve is fitted on the right. DNC- -V5 fitted on left 40 Internet: Subject to change 2017/11

41 Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combination Technical data General technical data Piston Cylinder Pneumatic connection G1/8 G1/4 G1/4 G3/8 G3/8 G1/2 Piston rod thread M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5 K3 M6 M8 M10 M10 M12 M12 K5 M10 M12 M16 M16 M20 M20 Constructional design Piston Piston rod Profile barrel Cushioning Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Cushioning length PPV [mm] Position sensing Via proximity sensor Type of mounting Via female thread Via accessories Mounting position Any Valve Ordering data Valves and accessories page 48 Valve used single CPE14-M1BH-5L-1/8 CPE18-M1H-5L-1/4 CPE24-M1H-5L-3/8 solenoid double CPE14-M1BH-5J-1/8 CPE18-M1H-5J-1/4 CPE24-M1H-5J-3/8 solenoid Pneumatic connection G1/8 G1/4 G3/8 Constructional design Piston spool valve Type of mounting Via mounting kit Operating voltage [V DC] / 15% Power consumption [W] Duty cycle 100% Protection class with plug socket IP65 -H- Note: This product conforms to ISO and to ISO Operating and environmental conditions Piston Operating medium Compressed air in accordance with ISO :2010 [7:4:4] Note on operating/pilot medium Operation with lubricated medium possible (in which case lubricated operation will always be required) Operating pressure [bar] Ambient temperature 1) [ C] Corrosion resistance class CRC 2) 2 Maritime classification 3) See certificate 1) Note operating range of proximity sensors 2) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. 3) Additional information Certificates. 2017/11 Subject to change Internet: 41

42 Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combination Technical data Force [N] and impact energy [J] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting S2/S S2/S Max. impact energy at the end positions 1) 1) The permissible impact energy is reduced by approx. 10% for variants K10 and S20 Permissible impact velocity: Maximum permissible load: 2xE perm. v perm. mdead m load m load 2xE perm. v 2 m dead v perm. Permissible impact velocity E perm. Max. impact energy m Intrinsic Moving load (drive) m Load Moving effective load -H- Note This data represents the maximum values that can be achieved. The maximum permissible impact energy must be observed. Max. lateral force Fq as a function of stroke length l Fq /63 80/ Internet: Subject to change 2017/11

43 Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combination Technical data Materials Sectional view Standard cylinder Basic version R8 S10 S11 K10 1 Profile barrel Wrought aluminium alloy, smooth anodised 2 Bearing and end caps Die-cast aluminium 3 Piston rod High-alloy steel Tempered steel High-alloy steel Wrought aluminium alloy, anodised Seals, cylinder Polyurethane, nitrile rubber Fluoro rubber Polyurethane, nitrile rubber 4 Housing, valve Die-cast aluminium, polyamide, steel Seals, valve Nitrile rubber Note on materials RoHS compliant 2017/11 Subject to change Internet: 43

44 Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combination Technical data Dimensions Download CAD data 1 Connecting cable not included in scope of delivery +1/2 = plus half stroke length 44 Internet: Subject to change 2017/11

45 Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combination Technical data [mm] B1 B2 E1 H1 H2 L1 max. L2 ±3 L3 L4 L5 ß1 ß G1/ G1/ G1/ G1/ G3/ G3/ H- Note: This product conforms to ISO and to ISO H- Note Additional dimensions relating to the basic version and its variants are provided on page 15, with clamping unit on page /11 Subject to change Internet: 45

46 Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combination Ordering data Modular products Ordering table Size Conditions 0M Module No Function Standard cylinder, double-acting, standard hole pattern, cylinder/valve combination DNC DNC Piston [mm] Stroke [mm] Cushioning Flexible cushioning rings/pads at both ends -P Pneumatic cushioning, adjustable at both ends -PPV 0O Position sensing Via proximity sensor -A Protection against rotation Square piston rod 1 -Q Type of piston rod Through piston rod 2 -S2 Through, hollow piston rod 3 -S20 Code Enter code 1 Q Max. stroke: mm In combination with S2: square piston rod at bearing cap end only In combination with KP: only supplied with S2 Not with S20, K7, K10, S10, S11 2 S2 In combination with K2: extended thread at both ends In combination with K3: female thread at both ends In combination with K5: special thread at both ends In combination with K8: piston rod extended at bearing cap end only In combination with KP: clamping unit at end cap Not with S20, K7, S10, S11 3 S20 Max. stroke: 850 mm Not with K2, K3, K5, K8, K10, KP, S10, S11 Transfer order code DNC 46 Internet: Subject to change 2017/11

47 Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combination Ordering data Modular products Ordering table Size Conditions Code Enter code Extended male thread Piston rod with extended male thread 0O [mm] K2 Female thread Piston rod with female thread (M6) (M8) (M10) (M10) (M12) (M12) 5 -K3 Special thread Piston rod with special thread M10 M12 M16 M16 M20 M K5 Special spanner flats Piston rod with external hexagon 7 -K7 Extended piston rod Extended piston rod [mm] K8 Improved running performance Smooth anodised aluminium coated piston rod 8 -K10 Clamping unit Attached 9 -KP Slow speed (constant motion) Slow speed (constant motion at low piston speeds) aj -S10 Running characteristics Low friction aa -S11 0M Cylinder/valve combination Single solenoid valve, fitted on right, piston rod retracted when unactuated -V1 Single solenoid valve, fitted on right, piston rod advanced when unactuated -V2 Double solenoid valve, fitted on right -V3 Single solenoid valve, fitted on left, piston rod retracted when unactuated -V4 Single solenoid valve, fitted on left, piston rod advanced when unactuated -V5 Double solenoid valve, fitted on left -V6 4 K2 Not with K3, K10 5 K3 With K5: on request Not with K7 6 K5 Not with K10 7 K7 Not with Q, S2, K10 8 K10 Max. stroke: 1000 mm Not with KP 9 KP Without S2: position of the clamping unit at the bearing cap Not with S10, S11 aj S10 Max. stroke: 500 mm; additional strokes on request Not with S11 aa S11 Max. stroke: 500 mm; additional strokes on request Transfer order code 2017/11 Subject to change Internet: 47

48 Standard cylinders DNC-V1 V6, standard hole pattern, cyl./valve combination Accessories Ordering data Valves For [mm] Pneumatic connection Protection class Part No. Type Technical data Internet: cpe Single solenoid 32 G1/8 IP CPE14-M1BH-5L-1/ G1/4 IP CPE18-M1H-5L-1/ G3/8 IP CPE24-M1H-5L-3/8 100 Double solenoid 32 G1/8 IP CPE14-M1BH-5J-1/ G1/4 IP CPE18-M1H-5J-1/ G3/8 IP CPE24-M1H-5J-3/8 100 Ordering data Valve accessories Push-in fitting QS For valve Part No. Type PU 1) Technical data Internet: qs CPE QS-1/8-8-I 10 CPE QS-1/4-10-I 10 CPE QS-3/8-12-I 10 Connecting cable NEBV/KMEB Technical data Internet: nebv CPE14 Cable length: 2.5 m NEBV-Z4WA2L-R-E-2.5-N-LE2-S1 1 Cable length: 5 m NEBV-Z4WA2L-R-E-5-N-LE2-S1 CPE18 Cable length: 2.5 m KMEB ,5-LED 1 CPE24 Cable length: 5 m KMEB LED Cable length: 10 m KMEB LED Mounting kit ZVB CPE ZVB-8-14/18 CPE18 CPE ZVB ) Packaging unit quantity 48 Internet: Subject to change 2017/11

49 Accessories Multi-position kit DPNC Material: Flange: Wrought aluminium alloy Threaded studs, hex nuts: Galvanised steel Free of copper and PTFE RoHS-compliant + = plus stroke length -H- Note The maximum overall stroke length must not be exceeded when combining cylinders and multi-position kits. Dimensions and ordering data For F1 ZJ Max. overall stroke length Weight Part No. Type [mm] Basic version KP [mm] [g] DPNC DPNC DPNC DPNC DPNC DPNC DPNC-125 Connecting two cylinders with identical piston diameter as a 3 or 4-position cylinder A 3 or 4-position cylinder consists of two separate cylinders whose piston rods advance in opposing directions. This means that depending on actuation and stroke division, this type of cylinder can assume up to four positions. In each case the cylinder is driven precisely against a stop. Note that when one end of the piston rod is fixed, the cylinder barrel executes the movement. The cylinder s connections must be flexible. To achieve 3 positions Two cylinders with identical stroke length must be connected together. To achieve 4 positions Two cylinders with different stroke lengths must be connected together. 2017/11 Subject to change Internet: 49

50 Accessories Foot mounting HNC/CRHNC Material: HNC: Galvanised steel CRHNC: High-alloy steel Free of copper and PTFE + = plus stroke length Dimensions and ordering data For AB AH AO AT AU SA TR US XA XS [mm] Basic version KP Basic version KP For Basic version High corrosion protection CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] HNC CRHNC HNC CRHNC HNC CRHNC HNC CRHNC HNC CRHNC HNC CRHNC HNC CRHNC-125 1) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Corrosion resistance class CRC 4 to Festo standard FN Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be supported by special tests ( also FN ) using appropriate media. 50 Internet: Subject to change 2017/11

51 Accessories Flange mounting FNC/CRFNG + = plus stroke length Material: FNC: Galvanised steel CRFNG: High-alloy steel Free of copper and PTFE RoHS-compliant Cannot be used on the bearing cap in combination with the bellows kit DADB Dimensions and ordering data For E FB MF R TF UF W ZF [mm] H13 DNC- DNC- -KP For Basic version Corrosion resistant CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] FNC CRFNG FNC CRFNG FNC CRFNG FNC CRFNG FNC CRFNG FNC CRFNG FNC CRFNG-125 1) Corrosion resistance class CRC 1 to Festo standard FN Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions). Corrosion resistance class CRC 4 to Festo standard FN Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be supported by special tests ( also FN ) using appropriate media. 2017/11 Subject to change Internet: 51

52 Accessories Trunnion flange ZNCF/CRZNG Material: ZNCF: Special steel casting CRZNG: Electrolytically polished special steel casting Free of copper and PTFE RoHS-compliant Cannot be used on the bearing cap in combination with the bellows kit DADB + = plus stroke length Dimensions and ordering data For C2 C3 TD TK TL TM US XH XL [mm] e9 DNC- DNC- -KP For Basic version Corrosion resistant CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] ZNCF CRZNG ZNCF CRZNG ZNCF CRZNG ZNCF CRZNG ZNCF CRZNG ZNCF CRZNG ZNCF CRZNG-125 1) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Corrosion resistance class CRC 4 to Festo standard FN Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be supported by special tests ( also FN ) using appropriate media. 52 Internet: Subject to change 2017/11

53 Accessories Trunnion mounting kit DAMT for basic version DNC The mounting kit can be attached at any position along the profile barrel of a cylinder. Material: Tempered steel Free of copper and PTFE + = plus stroke length +½ = plus half stroke length 1 Max. tightening torque for DNC-KP + = plus stroke length +½ = plus half stroke length 1 Max. tightening torque Dimensions and ordering data For B1 C2 C3 TD TL TM UW XG [mm] e9 DNC- DNC- -KP For XJ XV Max. tightening torque CRC 1) Weight Part No. Type [mm] DNC- DNC- -KP DNC- DNC- -KP [Nm] [g] DAMT-V1-32-A DAMT-V1-40-A DAMT-V1-50-A DAMT-V1-63-A DAMT-V1-80-A DAMT-V1-100-A DAMT-V7-125-A 1) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. 2017/11 Subject to change Internet: 53

54 Accessories Trunnion support LNZG Material: Trunnion support: Anodised aluminium Plain bearing: Polymer Free of copper and PTFE RoHS-compliant Dimensions and ordering data For CR DA FK FN FS H1 HB KE NH TH UL CRC 1) Weight Part No. Type [mm] D11 H13 ±0.1 H13 ±0.2 [g] LNZG-32 40, LNZG-40/50 63, LNZG-63/80 100, LNZG-100/125 1) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Trunnion support CRLNZG Material: High-alloy steel Free of copper and PTFE RoHS-compliant Dimensions and ordering data For CR FK FN FS H1 HB NH TH UL CRC 1) Weight Part No. Type [mm] D11 ±0.1 H13 ±0.2 [g] CRLNZG-32 40, CRLNZG-40/50 63, CRLNZG-63/80 100, CRLNZG-100 1) Corrosion resistance class CRC 4 to Festo standard FN Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be supported by special tests ( also FN ) using appropriate media. 54 Internet: Subject to change 2017/11

55 Accessories Swivel flange SNC Material: Die-cast aluminium Free of copper and PTFE RoHS-compliant + = plus stroke length 1 The pivot pin is protected against rotation with a dowel pin. Dimensions and ordering data For CG CP E EK FL L SR [mm] H14 h14 H9 ± / / For TG XC CRC 1) Weight Part No. Type [mm] DNC- DNC- -KP [g] SNC SNC SNC SNC SNC SNC SNC-125 1) Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. 2017/11 Subject to change Internet: 55

56 Accessories Swivel flange SNCB/SNCB- -R3 Material: SNCB: Die-cast aluminium SNCB- -R3: Die-cast aluminium with protective coating Free of copper and PTFE RoHS-compliant + = plus stroke length Dimensions and ordering data For CB E EK FL L MR TG UB XC [mm] H14 H9/e8 e8 ±0.2 h14 DNC- DNC- -KP / / For Basic version R3 High corrosion protection CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] SNCB SNCB-32-R SNCB SNCB-40-R SNCB SNCB-50-R SNCB SNCB-63-R SNCB SNCB-80-R SNCB SNCB-100-R SNCB SNCB-125-R3 1) Corrosion resistance class CRC 1 to Festo standard FN Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions). Corrosion resistance class CRC 3 to Festo standard FN High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial environment. 56 Internet: Subject to change 2017/11

57 Accessories Swivel flange SNCS/CRSNCS/SNCS- -R3 Material: SNCS 32 50: Die-cast aluminium SNCS : Wrought aluminium alloy CRSNCS 32 80: High-alloy stainless steel SNCS- -R : Wrought aluminium alloy with protective coating RoHS-compliant + = plus stroke length Dimensions and ordering data For CN E EP EX FL LT [mm] DNC- DNC- -R3 DNC- DNC- -R3 ±0.2 ± / / / / / ,5± / ,2± / / / / / / For MS RA TG XC DNC- DNC- -R3 DNC- DNC- -R3 DNC- DNC- -KP [mm] ±0.5 30± ±0.5 39± For Basic version High corrosion protection CRC 1) Weight Part No. Type CRC 1) Weight Part No. Type [mm] [g] [g] SNCS CRSNCS SNCS CRSNCS SNCS CRSNCS SNCS CRSNCS SNCS CRSNCS SNCS SNCS-100-R SNCS SNCS-125-R3 1) Corrosion resistance class CRC 1 to Festo standard FN Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive trunnions). Corrosion resistance class CRC 2 to Festo standard FN Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmosphere typical for industrial applications. Corrosion resistance class CRC 3 to Festo standard FN High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial environment. Corrosion resistance class CRC 4 to Festo standard FN Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be supported by special tests ( also FN ) using appropriate media. 2017/11 Subject to change Internet: 57