INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2013 ACCORD 2 AND 4-DOOR Publications No. AII Issue Date AUG 2012 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E Transmitter 3 Relays Flange nut Control unit 18 Wire ties Antenna Wire tie with clip 6 Urethane tapes ID label Clip Remote Control Engine Starter Attachment Kit P/N 08E92-T2A-100A (With Keyless Access System) Engine starter harness Caution label Control unit bracket Fuse label 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 08E92-T2A-1A of 29

2 Accessory User s Information Manual 6 Urethane tapes Quick Start Guide Clip Remote Control Engine Starter Attachment Kit P/N 08E92-T2A-100B (Without Keyless Access System) Engine starter harness Caution label Fuse label Control unit bracket Accessory User s Information Manual 3 Relays Quick Start Guide Flange nut 18 Wire ties Wire tie with clip 2 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

3 TOOLS AND SUPPLIES REQUIRED Flat-tip screwdriver Phillips screwdriver Ratchet 10 mm Socket 10 mm Open end wrench Isopropyl alcohol Shop towel Tape measure Scissors HDS/MVCI Masking tape Diagonal cutters Ruler Tape Utility knife The following tools are available through the Honda Tool and Equipment Program. On the in, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under Search. Or, call Trim Tool Set (T/N SOJATP2014) Plastic Trim Tool (T/N SILTRIMTL10) Illustration of the Remote Control Engine Starter in the Vehicle INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Disconnect the negative cable from the battery. 2. Attach the ID label. Using isopropyl alcohol on a shop towel, clean the area where the ID label will attach. Attach the ID label to the transmitter in the area as shown. With Keyless Memory Settings NOTE: The remote is factory set for driver 1 remote control. To program the driver 2 remote, follow the REMOTE CONTROL TRANSMITTER REGISTRATION instructions on ISIS. ID LABEL TRANSMITTER Clean with isopropyl alcohol. QB20939DH ENGINE STARTER 3 RELAYS 3A, 20A or 40A FUSES CONTROL UNIT QB20940AH 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 3 of 29

4 Without Keyless Memory Settings ID LABEL TRANSMITTER 3. If equipped, remove the roof console. Using a plastic trim tool, pry out and remove the left and right lenses (four retaining tabs each). Open the sunglass holder. Remove four screws. Remove the roof console (unplug the vehicle connectors). With Moonroof S Clean with isopropyl alcohol. QB32111CH ROOF CONSOLE SUNGLASS HOLDER (Open.) RIGHT LENS 4 SCREWS LEFT LENS 4 RETAINING TABS 4 RETAINING TABS QB20901BX 4 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

5 Without Moonroof S 5. Wrap the end of a flat-tip screwdriver with tape. Locate the slot in the bracket cover, and insert the flat-tip screwdriver into the slot. Push the hook with the screwdriver. FLAT-TIP SCREWDRIVER BRACKET COVER TAPE HOOK ROOF CONSOLE (if equipped) DRIVER S SUNVISOR FRONT SUNGLASS HOLDER (Open.) 4 SCREWS LEFT LENS 4 RETAINING TABS RIGHT LENS 4 RETAINING TABS QB20902AX Make sure the hook slides into the bracket cover. 4. Remove two sunvisor holders by rotating them 90 counterclockwise. Push the hook. While pushing in on the hook, rotate the sunvisor backward about 45. QB32101AX 6. While pushing in on the hook, rotate the driver s sunvisor backward about 45. Make sure the hook slides into the bracket cover. NOTE: If the hook did not stay pushed in, return the driver s sunvisor to its original position and repeat steps 5 and 6. DRIVER S SUNVISOR HOLDER (Rotate.) PASSENGER S SUNVISOR HOLDER (Rotate.) QB20903AX 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 5 of 29

6 7. Remove the driver s sunvisor (unplug the vehicle connector). 10. Insert a shop towel in the opening between the driver s A-pillar trim and the dashboard to prevent dropping the A-pillar clips. Take care not to damage the driver s A-pillar trim. DRIVER S A-PILLAR DRIVER S A-PILLAR TRIM FRONT DRIVER S SUNVISOR QB20904AX 8. Pull away the driver s door opening seal in the area shown. SHOP TOWEL QB20906AX Pull the clip. 11. Slide up the driver s A-pillar trim to remove it from the upper clip. Carefully remove the shop towel and any clips that fell from the driver s A-pillar trim. NOTE: The upper clip will stay in the body. UPPER CLIP DRIVER S A-PILLAR TRIM DOOR OPENING SEAL (Pull away.) 2 CLIPS QB20905AX DRIVER S A-PILLAR TRIM 9. Pull out on the driver s A-pillar trim to release the clips. QB20907AX 6 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

7 12. Remove the remaining upper clip from the driver s A-pillar. 14. If equipped, remove the driver s dashboard under cover (turn the knob and two clips). 2 TABS (Push.) 2 CLIPS DRIVER S A-PILLAR UPPER CLIP (Discard.) QB20908AX 13. Install the new clip (supplied) to the driver s A-pillar trim, but do not reinstall the trim at this time. DRIVER S DASHBOARD UNDER COVER (if equipped) KNOB (Turn.) QB20201AB CLIP (supplied) 15. Remove the driver s dashboard lower cover (nine clips and unplug the vehicle connectors, if equipped). S (if equipped) 9 CLIPS DRIVER S A-PILLAR TRIM Q0N0533AH DRIVER S DASHBOARD LOWER COVER QB20202BB 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 7 of 29

8 16. Remove the cover (six retaining tabs). Using the ignition key, unlock the trunk lid/fuel fill door opener, then remove the key. 18. Remove the driver s door sill trim. 4-Door: Two retaining tabs and four clips. KEY SELF-TAPPING SCREW 6 RETAINING TABS 4 CLIPS 2 RETAINING TABS Unlock. COVER TRUNK LID/FUEL FILL DOOR OPENER DRIVER S DOOR SILL TRIM QB20804AB 2-Door: Two retaining tabs and six clips. 6 CLIPS DRIVER S DOOR SILL TRIM QB32110AH 17. Remove one self-tapping screw from the trunk lid/ fuel fill door opener cover. 2 RETAINING TABS DRIVER S DOOR SILL TRIM QB32112AH 8 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

9 19. Pull away the door opening seal, and remove the driver s kick panel (two clips). 21. Turn the steering wheel 90 clockwise. Using a plastic trim tool, release the retaining tab. UPPER COLUMN COVER DOOR OPENING SEAL (Pull away.) 2 CLIPS DRIVER S KICK PANEL QB20805AB 20. Lower the tilt lever, and release the column band (two clips). If the vehicle is equipped with keyless access system, reconnect the negative cable to the battery, then press the engine start/stop button to select the ON mode. STEERING WHEEL STEERING WHEEL 22. Turn the steering wheel 180 counterclockwise. Using a plastic trim tool, release the retaining tab. UPPER COLUMN COVER RETAINING TAB PLASTIC TRIM TOOL QB32114AH 2 CLIPS COLUMN BAND RETAINING TAB UPPER COLUMN COVER STEERING WHEEL STEERING WHEEL QB32113AH PLASTIC TRIM TOOL QB32115AH 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 9 of 29

10 23. Remove the upper column cover (two retaining tabs and two hooks). 2 RETAINING TABS 25. Turn the steering wheel 180 clockwise, and remove the other self-tapping screw from the lower column cover. 2 HOOKS UPPER COLUMN COVER SELF-TAPPING SCREW QB32116AH 24. Remove one self-tapping screw from the lower column cover. LOWER COLUMN COVER QB32118AH 26. Remove the lower column cover (one self-tapping screw). STEERING WHEEL LOWER COLUMN COVER SELF-TAPPING SCREW QB32117AH LOWER COLUMN COVER SELF-TAPPING SCREW QB32119AH 27. If the vehicle is equipped with keyless access system, press the engine start/stop button to select the OFF mode. Disconnect the negative cable from the battery. 10 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

11 Installing the Antenna 28. Using scissors, cut one urethane tape in half. Wrap two halves of urethane tape to the antenna cable as shown. 29. Starting near the antenna end of the cable, wrap one urethane tape around the antenna cable at the measurements shown. CABLE 60 mm (2.4 in.) 60 mm (2.4 in.) 220 mm (8.7 in.) CABLE URETHANE TAPE 560 mm (22.0 in.) CABLE URETHANE TAPE (Cut in half.) HALVES OF URETHANE TAPE QB62501BK (Do not fold the antenna cable.) 2 URETHANE TAPES (Cut in half.) HALVES OF URETHANE TAPE QB20901CH 30. Using scissors, cut two urethane tapes in half. Wrap four halves of urethane tape around the antenna cable at the measurements shown American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 11 of 29

12 31. Attach the antenna. Attach masking tape to the windshield at the measurement shown. Fold the adhesive backing of the antenna as shown. With Camera Cover MASKING TAPE 10 mm (0.4 in.) CAMERA COVER ADHESIVE BACKING HEADLINER Without Camera Cover QB51403BH QB51401CH Using isopropyl alcohol on a shop towel, clean the windshield where the antenna will attach. Attach the antenna with masking tape. Adjust the position of the antenna so there is equal spacing on both sides. MASKING TAPE Clean with isopropyl alcohol. HEADLINER 50 mm (2.0 in.) HEADLINER Equal spacing on both sides. MASKING TAPE QB51402BH QB51404CH 12 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

13 Carefully remove the adhesive backing from the antenna, and attach the antenna to the windshield. Press and hold the antenna firmly in place for 30 seconds. Remove the masking tape. 33. Route the antenna cable down the A-pillar as shown. Using five wire ties, secure the antenna cable to the vehicle harness. CABLE 5 WIRE TIES ADHESIVE BACKING (Remove.) MASKING TAPE (Remove.) FRAME CABLE QB20905AH QB51405CH 32. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner. HEADLINER 34. Pull away the door opening seal. Route the antenna cable down next to the dashboard, and tuck the antenna cable between the driver s A-pillar and the dashboard. Reinstall the door opening seal. DRIVER S A-PILLAR DOOR OPENING SEAL (Pull away) CABLE DASHBOARD CABLE QB20906BH QB20904CH 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 13 of 29

14 Routing the Engine Starter Harness 35. Using isopropyl alcohol on a shop towel, clean the areas where the fuse labels will attach. 38. Using scissors, cut one urethane tape to the measurements shown. Wrap the cut urethane tape around the engine starter harness 5-pin connector. 20A or 40A FUSE LABEL Clean with isopropyl alcohol. VIEW FROM URETHANE SIDE 20 mm (0.8 in.) 5-PIN 3A FUSE LABEL 20A or 40A FUSE LABEL Clean with isopropyl alcohol. 25 mm (1.0 in.) 3A FUSE LABEL URETHANE TAPE RELAY BLOCK QB20907AH 36. Attach two 20A fuse labels (with keyless access system) or two 40A fuse labels (without keyless access system) and two 3A fuse labels to the engine starter harness relay block. QB20909AH 37. Install three relays to the engine starter harness relay blocks. 3 RELAYS ENGINE STARTER RELAY BLOCKS QB20908AH 14 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

15 39. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Plug the vehicle 5-pin connector into the engine starter harness 5-pin connector. NOTICE: Make sure the engine starter harness 5-pin connector is securely connected to the fuse box 5-pin connector. A loose connection can cause the engine to stall. 40. Using two wire ties, secure the engine starter harness to the vehicle harness. FUSE BOX Connector unlock 5-PIN Connector lock 1 Plug. 2 WIRE TIES ENGINE STARTER QB20911AH 41. Plug the engine starter harness 4-pin connector into the fuse box. 2 Pull. 1 Push. 3 Unplug. 2 Push. FUSE BOX 4-PIN 5-PIN 4-PIN QB20912AH 5-PIN S QB20910CH 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 15 of 29

16 42. Route the engine starter harness as shown. Remove the tape from the vehicle harness. Do not damage the vehicle harness. 44. Unplug the vehicle 28-pin connector, and plug it into the engine starter harness 28-pin connector. Plug the engine starter harness 28-pin connector into the vehicle 28-pin connector. FUSE BOX TAPE (Remove, if equipped.) 28-PIN S 28-PIN 28-PIN S QB20913CH 43. Attach the engine starter harness 28-pin connector to the vehicle connector. 28-PIN 28-PIN 28-PIN QB20914BH 16 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

17 With Keyless Access System 45. Remove the tape from the engine starter harness 2-pin connector. Unplug the vehicle 2-pin connector, and plug it into the engine starter harness 2-pin connector. Plug the engine starter harness 2-pin connector into the vehicle 2-pin connector. Without driver s dashboard under cover 46. Using a utility knife, cut the dashboard insulator as shown. Go to step 48. SLIT TAPE (Remove.) FUSE BOX Cut. If equipped, do not connect. 2-PIN 2-PIN DASHBOARD INSULATOR (Cut.) BRAKE PEDAL QB20916AH With driver s dashboard under cover 47. Remove the cap from the vehicle bolt. 2-PIN 2-PIN S QB20915CH CAP BOLT QB20917AH 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 17 of 29

18 48. Using a utility knife, cut the dashboard insulator to the measurements shown. Do not damage the vehicle panel. 51. Plug the antenna cable connector and engine starter harness 28-pin connector into the control unit. FUSE BOX 15 mm (0.6in.) 15 mm (0.6in.) CONTROL UNIT Cut. CABLE DASHBOARD INSULATOR BOLT QB20918AH 49. Using isopropyl alcohol on a shop towel, clean the control unit where the urethane tape will attach. URETHANE TAPE (Cut in half.) 52. Install the control unit bracket to the control unit. CONTROL UNIT BRACKET 28-PIN QB20920AH CONTROL UNIT Align. URETHANE TAPE Clean with isopropyl alcohol. CONTROL UNIT QB20921AH QB20919BH 50. Using scissors, cut the urethane tape in half, then wrap the urethane tape around the control unit. 18 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

19 53. Secure the engine starter harness clip to the control bracket. 55. Using one flange nut, secure the control unit bracket to the vehicle panel as shown. CLIP CONTROL UNIT CONTROL UNIT BRACKET FLANGE NUT PANEL CONTROL UNIT BRACKET QB20922AH 54. Using two wire ties, secure the antenna cable to the engine starter harness. CABLE 56. Secure the engine starter harness clip to the vehicle bolt. CLIP CONTROL UNIT BRACKET QB20924AH 2 WIRE TIES BOLT CONTROL UNIT BRACKET QB20923AH QB20925AH 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 19 of 29

20 57. Using isopropyl alcohol on a shop towel, clean the control unit bracket where the urethane tape will attach. URETHANE TAPE (Cut.) URETHANE TAPE 60. Attach the engine starter harness relay blocks to the control unit bracket. CONTROL UNIT BRACKET RELAY BLOCKS Cut in step 50. Clean with isopropyl alcohol. CONTROL UNIT BRACKET QB20926AH 58. Using scissors, cut the urethane tape in half as shown, then attach the urethane tape to the control unit bracket. With driver s dashboard under cover 59. Reinstall the cap to the vehicle bolt. CONTROL UNIT BRACKET 61. Remove the vehicle ground bolt. QB20928AH CAP (reused) GROUND BOLT (reused) GROUND TERMINAL GROUND TERMINAL QB20929CH CONTROL UNIT BRACKET BOLT QB20927AH 62. Attach the engine starter harness ground terminal to the vehicle ground terminal, and reinstall the vehicle ground bolt. 20 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

21 63. Using one wire tie, secure the antenna cable and engine starter harness to the vehicle harness. WIRE TIE FUSE BOX 2-PIN (if equipped) 65. Secure the engine starter harness to the hole in the vehicle frame with one wire tie with clip at the white tape on the engine starter harness. NOTE: If another accessory harness is already attached, align the white tape on the engine starter harness with the clip on the other harness. Using one wire tie with clip, secure the engine starter harness to the other accessory harness. WHITE TAPE WIRE TIE WITH CLIP ENGINE STARTER CABLE QB20930CH 64. Bundle up the excess antenna cable as shown. Using two wire ties, secure the antenna cable and engine starter harness to the vehicle harness. WIRE TIE WITH CLIP 20 mm (0.8 in.) or above. OTHER ACCESSORY CLIP WHITE TAPE WITH OTHER ACCESSORY QB20932AH ENGINE STARTER 2 WIRE TIES CABLE (Bundle.) QB20931DH 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 21 of 29

22 66. Route the 12-pin/10-pin connector ends of the engine starter harness as shown. 69. Route the engine starter harness as shown. Unplug the vehicle 10-pin connector, and plug it into the engine starter harness 10-pin connector. Plug the remaining engine starter harness 10-pin connector into the wiper switch. Inside ENGINE STARTER CLIP WHITE TAPE 10-PIN 2 WIRE TIES QB20933AH 67. Align the white tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness using one wire tie. 68. Using one wire tie, secure the engine starter harness to the vehicle harness. WIPER SWITCH 10-PIN 10-PIN QB20934AH 22 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

23 70. Using one wire tie, secure the 10-pin connector and the engine starter harness to the vehicle harness. Do not undue strain to the 10-pin connector cord. 71. Route the engine starter harness as shown. Unplug the vehicle 12-pin connector, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the combination light switch. IGNITION SWITCH WIRE TIE ENGINE STARTER 12-PIN 10-PIN 12-PIN QB20935BH 12-PIN COMBINATION LIGHT SWITCH QB20936AH 2012 American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 23 of 29

24 72. Using three wire ties, secure the engine starter harness to the vehicle harness. Do not secure it to the SRS harness. NOTE: Make sure that the connectors and harness are not pinched, or are not interfering with the steering wheel when it is moved for adjustment. Do not pull the 12-pin connector cord wire too tight. 73. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will attach. Clean with isopropyl alcohol. 2 WIRE TIES WIRE TIE CAUTION LABEL QB20938AH 74. Attach the caution label to the hood in the area shown. QB20937BH 75. Check that all wire harnesses are routed properly and all connectors are plugged in. 76. Check the overlap between the headliner and the driver s A-pillar trim. Refer to the Service Manual. If necessary, adjust the overlap. 77. Reinstall all removed parts. 78. Reconnect the negative cable to the battery. 79. Press and hold the radio power button for two seconds to restore the radio and navi (if equipped) system functions. 80. Reset the clock. 81. Perform the REMOTE REGISTRATION and the FUNCTION CHECK. 24 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

25 REMOTE REGISTRATION 1. Acquire the PCM Code from the Interactive Network. Select Honda Systems. CAR ICON CHECK BUTTON QB32103AH QB40150AH 2. Connect the HDS/MVCI tester to the OBD II data link connector, then turn the ignition switch to the on (II) position. 3. Start the HDS, and click the car icon. 4. Input the VIN and other required information into the HDS, then click the check button. 6. Select R/C ENG STARTER and click the check button. Select R/C ENG STARTER. CHECK BUTTON QB32104AH Input the VIN and other required information. CHECK BUTTON QB32102BH 5. Select Honda Systems, then click the check button American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 25 of 29

26 7. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT. 9. Input the PCM-code, then click the check button. NOTE: To ensure security, the PCM-code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM-code acquisition and registration are different. The date of the HDS/MVCI tester should also be the same. Input the PCM-Code. CHECK BUTTON QB32105BH 8. The following message will display: Obtain PCMcode (IMMOBILIZER PCM CODE) from in. This vehicle s VIN will be required to obtain the password. (USA) Click the check button. Obtain PCM-code message. CHECK BUTTON QB32107BH 10. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Turn the ignition switch off. CHECK BUTTON QB32106AH 26 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

27 The registration of the Remote Control Engine Starter Unit has been completed. QB32108CH 11. The following message will display: Check that engine can be started by the Transmitter. Click the check button American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 27 of 29

28 Check that engine can be started by the Transmitter. CHECK BUTTON QB32109CH 12. Perform the FUNCTION CHECK on page 28, then disconnect the HDS/MVCI. FUNCTION CHECK Operating Conditions The hood is closed The shift lever is in park Turn the ignition switch off and the key is outside the vehicle All doors and trunk lid closed and locked Inspection 1. Press the engine/command button on the transmitter and release, within 2 seconds, press the lock/start button on the transmitter. The engine should start if all operating conditions are met. Does the engine start? Yes - Operation is normal. No: Make sure all Operating Conditions are met. Check the engine starter harness connections. Connect the HDS/MVCI and check for an indicated failure. (Refer to the appropriate Service Manual for details.) 28 of 29 AII (1208) 2012 American Honda Motor Co., Inc. All Rights Reserved.

29 2. Press the engine/command button on the transmitter and release, within 2 seconds, press the unlock/stop button. The engine should stop. Does the engine stop? ENGINE START OPERATION RECEPTION INDICATOR CHECKING INDICATOR Yes - Operation is normal. No - Check the engine starter harness connections. 3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions: NOTE: After each test the ignition key must be cycled, or the driver s door must be opened and closed. Move the shift lever out of the P position. Unlock or open the doors or the trunk lid. Open the hood. Insert the key in the ignition. If the vehicle is equipped the keyless access system, press the engine start/stop button. Press on the brake pedal. Does the engine stop after each of these tests? Yes - Operation is normal. No - Check the engine starter harness connections. ENGINE/ COMMAND BUTTON UNLOCK/ STOP BUTTON LOCK/ START BUTTON B127121H IN-CAR TEMPERATURE *1 Blinking ENGINE RUNNING INDICATOR REMAINING IDLING TIME *1 Only on vehicles equipped with the automatic climate control. This indicator is displayed for some vehicles among them. 4. Check that the power windows and the moonroof do not function, and the shift lever does not move to any position when the engine is started with the transmitter. 5. If the vehicle is equipped with the keyless access system, check that the engine does not start under Operating Conditions with the key left inside the vehicle. 6. Start the engine again, press the engine/command button on the transmitter two times, and check the vehicle condition on the display. 7. Check the operation of the transmitter when the vehicle is 120 m (400 ft.) away and in direct sight. 8. Press the unlock/stop button on the transmitter and verify that the doors unlock. Press the lock/start button, and verify that the doors lock. For the vehicle equipped with the memory seat, make sure to shift the seat position of driver s seat to Driver 1 by unlock of transmitter. 9. Check that the engine can start by the vehicle key and that the wiper and the headlight can be operated normally. * American Honda Motor Co., Inc. All Rights Reserved. AII (1208) 29 of 29