KAWASAKI TWO CYLINDER CONDENSED SERVICE DATA T1A340F1

Size: px
Start display at page:

Download "KAWASAKI TWO CYLINDER CONDENSED SERVICE DATA T1A340F1"

Transcription

1 Kawasaki pulley. Release rope and allow recoil spring to unwind. Remove retaining nut (3) and components (6 thru 8). Carefully remove rope pulley so that recoil spring remains in cover. If necessary to remove recoil spring, guard against uncontrolled uncoiling of spring which may cause personal injury. To assemble starter, install recoil spring in cover so that spring is wound ENGINE MODEL Bore (mm) es ^ Stroke (mm) es No. of Cylinders Displacement (cc) Cubic es Horsepower (c RPM Cooling Number Used Point Gap (mm) Timing BTDC (mm) Electrode Gap (mm) Fuel/Oil Ratio in counterclockwise direction and outer hook of spring contacts lug of cover. Install rope pulley and rope so that lug of pulley engages with inner hook of recoil spring. Install washer (8), pawls (7), spring (6) and pawl return spring (5). Install retainer cover (4) so that end of return spring (5) protrudes through retainer cover (4) and turn retainer cover one-third turn clockwise to pre-load spring. Install washers and ENGINES retaining nut. If rope handle was not removed during disassembly, position rope in notch of rope pulley and turn pulley two turns counter-clockwise to pre-load recoil spring. If handle was removed, turn rope pulley counterclockwise two or three turns and insert end of rope through rope outlet in cover. Tension on rope should be apparent. Tie a temporary knot to hold rope and install rope handle. KAWASAKI TWO CYLINDER CONDENSED SERVICE DATA TA340F (w 7500 HR : TA340S (a : TA400F (il : => May be equipped with Capacitor Discharge Ignition; all data is for Energy Transfer models. TA400S (ii) : *TA44OF : TA440S : ENGINE MODEL TB340S Bore (mm) es.36 Stroke (mm) es.36 No. of Cylinders Displacement (cc) Cubic es 0.7 Horsepower RPM Cooling Number Used Point Gap (mm) Timing BTDC 0.4 mm Electrode Gap (mm) Fuel/Oil Ratio 0: TB400S mm : TB440S mm : TC340SA WFIA rni Electronic 5^ 00 rpm 0: TC440SA WFIA GDI Electronic 5 00 rpm 0: TD50F ET 0.0-O.Oie 5 BR8ESA : 38

2 ENGINES CONDENSED ENGINE MODEL TD340F Bore (mm) es.36 Stroke (mm) es.36 No. of Cylinders Displacement (cc) Cubic es 0.7 Horsepower RPM Cooling Number Used ET Point Gap (mm) Timing BTDC 5 BR8ESA Electrode Gap (mm) Fuel/Oil Ratio 0: SERVICE DATA CONT. TD340AA WF7 CDI 5 00 rpm 0: TD440AA WF7 CDI 5 00 rpm 0: T7C340FR Dual CDI 4 00 rpm BR9EVA 0: Kawasaki T7C440FR Dual CDI 7 00 rpm BR9EVA 0: MAINTENANCE SPARK PLUG. The recommended plug for normal service is given in CONDENSED SERVICE DATA Table. A different heat range or type of plug may be needed for a particular application. Refer to ENGINE SERVICE FUNDAMENTALS Section when selecting a spark plug for other than normal usage. Some engines use a heat indicator thermo couple instead of a spark plug gasket. REMOVE GASKET if thermo couple is used. Thermo couple sensor (lead terminal) must be installed DOWNWIND from cooling air blast when spark plug is tightened; directly to rear on free air models or at 7-o'clock position on axial fan units. CARBURETOR. Mikuni, Tillotson or Walbro carburetors are used. Refer to the appropriate CARBURETOR SER- VICE Section for overhaul data. An external impulse line from engine crankcase is used to operate fuel pump. Be sure there are no vacuum or pressure leaks. IGNITION SYSTEM. Timing specifications for individual engines are given in CONDENSED SERVICE DATA Tables. Breaker point gap may be adjusted after removing recoil starter, starter pulley and inspection cover. To renew breaker points, the flywheel must be removed. On models having an energy transfer type ignition system, timing marks are found on fan cover and flywheel. Flywheel has two "F" marks which are 80 apart. To check timing, connect one lead of a light or buzzer to the black wire coming from either cylinder of the engine and ground the other lead on the engine. Timing is correct if points separate when one of the "F** marks is aligned with the stationary mark on the fan cover. Check timing of other cylinder using corresponding black wire and second "F" mark on flywheel. On models with capacitor discharge system, ignition timing is checked using an automobile type timing light with engine running. To check the timing, remove recoil starter and install a suitable power timing light. Solidly support rear of machine with a hoist so track can turn freely without danger of accident. Start and run engine at 00 rpm. With timing light directed at flywheel rim the scribed *T" mark on flywheel should align with cast timing boss on fan housing. If "T" mark is clockwise from stationary mark, timing is retarded; if counterclockwise, timing is advanced. Because timing is electronic, it should not change once properly adjusted. The first step in adjustment, therefore, would be to check for loose flywheel nut, sheared flywheel key, or loose mounting screws on stator base plate. To adjust the timing, stop engine and remove the three screws retaining emergency starter pulley and belt pulley. Remove the pulleys and, working through holes in flywheel, loosen the two stator base plate mounting screws. Move stator plate clockwise to retard the timing or counter-clockwise to advance the timing. Tighten screws securely then recheck running timing. LUBRICATION. The engine is lubricated by mixing oil with fuel. A good quality two-cycle oil designed for aircooled engines is recommended. Recommended fuel oil ratio for all engines is 0:. Mix fuel and oil thoroughly in a separate container before pouring mixture into fuel tank. For cold weather blending, pre-mix the oil with a small amount of gasoline and shake thoroughly until the mixture is liquid, then blend with remainder of fuel. Do not use kerosene or fuel oil for pre-mixing. REPAIRS TIGHTENING TORQUES. Recom mended tightening torques are as follows: Cylinder head 6 ft.-lbs. (. kg-m) Crankcase nuts 6 ft.-lbs. (. kg-m) Crankcase bolts 5 ft.-lbs. (0.7 kg-m) Flywheel nut ft.-lbs. (8.3 kg-m) Recoil starter mounting bolts 5 ft.-lbs. (0.7 kg-m) Spark plug 0 ft.-lbs. (.8 kg-m) DISASSEMBLY AND REASSEM- BLY. Remove carburetor, muffler, drive sheave and recoil starter. On models with axial fans, remove fan belt and fan assembly. Remove cooling shrouds. Remove starter cup, flywheel and ignition coils. Mark position of magneto base assembly and remove the two retaining screws from slotted holes; wiring loom fits in a grommet in crankcase parting line and magneto assembly cannot be lifted out until crankcase is split. Remove cylinder heads, cylinders and pistons and mark so that they will be installed in their original positions. Remove ten nuts and one bolt and separate crankcase halves. Refer to appropriate section to service components. To reassemble, reverse disassembly procedure. Tighten crankcase nuts to 6 ft.-lbs. and crankcase bolt to 5 39

3 Kawasaki ft.-lbs. Refer to Fig. for tightening sequence. PISTON, RINGS & CYLINDER. Piston pins are fully floating. Piston rings are pinned in place as shown in Fig.. Bottom ring is equipped with an expander. Top ring is identified by " NPR'* stamped on upper surface of ring. Bottom ring is stamped " NPR". Notches of ring ends must be up when ring is installed as shown in Fig.. Piston ring end gap for 50 and 340 cc models should be inch ( 0.35 mm). Piston ring end gap for 440 cc models should be inch ( mm). Top ring side clearance should be inch (0.- mm) and lower ring side clearance should be inch ( mm) for all models. Piston pin and piston pin bearing are available only as a matched pair and must be renewed as a set. It may be necessary to heat piston to install piston pin. Piston crown is marked with an arrow as shown in Fig. 3 to indicate piston position in cylinder. Arrow must point towards exhaust port. Piston skirt to cylinder wall clearance should be inch ( mm) for all engines. Cylinder has a chrome bore. Small deposits of aluminum from piston on cylinder wall may be removed by very careful sanding. Cylinder should be inspected for cracking, flaking or other deterioration of the chrome lining. Also check for appearance of underlying base metal through chrome which indicates excessive wear. CRANKSHAFT & CONNECTING ROD ASSEMBLY. The crankshaft and connecting rod are available only as an assembled unit and should not be disassembled. Crankshaft main bearings are a press fit on crankshaft. Support crankshaft between counterweights»as shown in Fig. 4 when pressing bearings on shaft. Crankshaft runout should not exceed 0.00 in. (0.03mm). Radial play of connecting rod big end should not exceed in. (0.03mni). Crankshaft end play should not exceed in. (0.77mm). If crankshaft, bearings or crankcase are renewed, crankshaft must be centered in crankcase by measuring the clearance between counterweight and crankcase wall at each end; then varying the thickness of selective washers (S Fig. 5). It is suggested, therefore, that if shaft bearings are removed the washers be properly identified and reinstalled on correct end of shaft. If crankcase is the item ENGINES renewed, make a trial installation in the new crankcase before bearings are removed; then install thicker or thinner washers as required to center the shaft. Factory recommended method of centering is to use dummy bearings which are the same dimensions as regular bearings but a slip fit on shaft journals. Washers (S) are available in thicknesses of 0.004, 0.008, 0.0, 0.06, 0.00 and 0.04 inch (0., 0., and 0.6 mm). ELECTRICAL SYSTEM. Fig. 7 shows an exploded view of flywheel magneto and CD ignition system used on most models. Ignition timing should be correct when timing scribe line (T) aligns with timing boss on crankcase. Timing can only be checked with a power timing light as outlined in MAINTENANCE Section, but can be adjusted without major disassembly by reaching through holes in flywheel (), loosening the two slotted head screws retaining base plate (5) to crankcase. and moving base plate in slotted holes. The condition of coils (, 3 and 4) can be checked with an ohmmeter without removal of flywheel or major disassembly. Disconnect the two individual plugs and multi-plug leading to wire loom (8). Check the pulser coil () by connecting the two ohmmeter leads to the individually connected (RED) and (WHITE) leads; reading should be 3.5 ohms. Check the exciter coil (3) by connecting ohmmeter leads to the individual (RED) lead and a suitable engine ground; reading should be 95 Fig, 3 instaii piston so that arrow on piston crown points towards exhaust port. Fig. Follow the above tightening sequence when installing crankcase nuts and boit. Refer to text for tightening torque. Fig. S View of engine crankshaft with end bearings expioded. Shims (5) control end piay and center shaft in crankcase. Fig. Piston rings are pinned as shown {arrow). Note that upper ring is installed so that notches in ring ends are up. 30 Fig. 4 A support shouid be placed between crankshaft counterweights when pressing bearings on shaft. Fig. e Crankshaft unit instaiied in crankcase upper haif. Counterweights must center in crankcase within inch {0.3 mm). Refer to Fig. 5.

4 ENGINES ohms. Check the lighting coil (4) by connecting ohmmeter probes to the TWO YELLOW leads in multi-plug; reading should be 0.8 ohms. Some models are equipped with a temperature indicator light which connects to a thermal switch threaded into right cylinder head. Heat indicator light should test 4 ohms when checked between the terminals on back of light bulb. Heat indicator thermal switch which is threaded into cylinder head should test at infinity when test probes are connected to terminal wire and threaded end and unit is at normal room temperature. When unit is heated to 500 degrees F. and retested, resistance should be at zero ohms. Some models are equipped with individual temperature gages which operate from thermocouples which substitute for the regular spark plug gasket for each cylinder. The gage is calibrated to register from COLD at a sensor temperature of 50 degrees F. or below, to HOT at a temperature of 475 degrees F. or above; with intermediate readings between the two extremes. Gage unit can be considered satisfactory if it registers '*COLD*' when engine is first started; and "HOT" when a jumper wire is touched to sensor wire and a suitable ground. Sensor units are affected by cooling air blast and should be installed "downwind" from the direction of cooling air flow; directly to the rear (six-o'clock) on free air models or at seven-o'clock on axial fan units. Sensor unit should register,000 ohms at -70 degrees F. and resistance should lower as temperature rises. Resistance should be approximately 6 ohms at 455 degrees F. RECOIL STARTER. Refer to ex ploded view of starter in Fig. 8. To disassemble starter, remove starter from engine and remove waterproofing plate. Pull rope out until it is possible to position rope in notch of rope pulley. Release rope and allow recoil spring to unwind. Remove retaining nut (3) and components (6 thru 8). Carefully remove rope pulley so that recoil spring remains in cover. If necessary to remove recoil spring, guard against uncontrolled uncoiling of spring which may cause personal injury. To assemble starter, install recoil spring in cover so that spring is wound in counterclockwise direction and outer hook of spring contacts lug of cover. Install rope pulley and rope so that lug of pulley engages with inner hook of recoil spring. Install washer (8), pawls (7), spring (6) and pawl return spring Fig. 7 Exploded view of typical engine electrical system used on models with CD ignition system.. Flywheel. Pulser coil 3. Exciter coil 4. Lighting coil 5. Base plate 6. CD unit 7. Ignition coil 8. Wiring harness T. Timing mark Kawasaki Fig. 8 Expioded wiew of recoii starter.. Starter cup 3. Nut 4. Retainer 5. Return spring 6. Spring 7. Pawls 8. Washer 9. Rope pulley 0. Recoil spring. Rope. Cover 3. Handle 4. Retainer Fig. 9 Exploded view of cooling fan and housing unit.. Cover. Nut 3. Lockwasher 4. PuUey half 5. Shims 6. Pulley half 7. Belt 8. Bearing 9. Shim 0. Snap ring. Housing. Bearing 3. Key 4. Fan (5). Install retainer cover (4) so that end of return spring (5) protrudes through retainer cover (4) and turn retainer cover one-third turn clockwise to pre-load spring. Install washers and retaining nut. If rope handle was not removed during disassembly, position rope in notch of rope pulley and turn pulley two turns counterclockwise to pre-load recoil spring. If handle was removed, turn rope pulley counterclockwise two or three turns and insert end of rope through rope outlet in cover. Tension on rope should be apparent. Tie a temporary knot to hold tope and install rope handle. 3

5

TIGHTENING TORQUES. Recommended tightening torques are as follows: Fanwheel Cap Screw ft.-lbs.

TIGHTENING TORQUES. Recommended tightening torques are as follows: Fanwheel Cap Screw ft.-lbs. OVERHAUL Refer to Fig. 8 for exploded view of crankshaft, crankcase and associated parts. Cylinder is closed end type, install with exhaust ports to bottom. Crankshaft and center main bearing housing are

More information

HUSQVARNA. Stroke mm (in.) 32.0 (1.26) 32 (1.26) optimum performance under cutting

HUSQVARNA. Stroke mm (in.) 32.0 (1.26) 32 (1.26) optimum performance under cutting CHAIN SAW Model Bore mm (in.) 40 Rancher, 140S, 240 S, 240 SE, 240 SG, 340 SE, 340 SG 40.0 (1.575) 44, 44 CB, 44 Rancher, 444 CB, 444 SE, 444 SG 42 (1.654) Stroke mm (in.) 32.0 (1.26) 32 (1.26) Displacement

More information

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES TEST AND ADJUSTMENT Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking (Minimum).......................... 28 kpa (4 psi) Oil Pressure.....................................

More information

McCULLOCH. Stroke. 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.)

McCULLOCH. Stroke. 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) SERVICE MANUAL Model Eager Beaver 2010, Mac 3210 Silver Eagle 2012 Eager Beaver 2014, Mac 3214, Silver Eagle 2014 Eager Beaver 2016, Mac 3216, Silver Eagle 2016 Bore Stroke DispL (2.1 cu. in.) (2.1CU.

More information

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES

SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking

More information

00-33A-01 CS-330T, CS-360T 1

00-33A-01 CS-330T, CS-360T 1 00-33A-01 CS-330T, CS-360T 1 0 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice.

More information

80-52A-00 EA Reference No A-00 ISSUED:

80-52A-00 EA Reference No A-00 ISSUED: 80-52A-00 EA-500 1 lntroduction We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications,

More information

10-25J-00 SRM-261T 1 INTRODUCTION. Reference No J-00 ISSUED:

10-25J-00 SRM-261T 1 INTRODUCTION. Reference No J-00 ISSUED: 10-25J-00 SRM-261T 1 1 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications

More information

01-36D-02 CS INTRODUCTION. Reference No D-02 ISSUED:

01-36D-02 CS INTRODUCTION. Reference No D-02 ISSUED: 01-36D-02 CS-370 1 0 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications,

More information

SERVICE MANUAL SUPPLEMENT

SERVICE MANUAL SUPPLEMENT 21-63H-01 PB-770H, PB-770T 1 SERVICE MANUAL SUPPLEMENT 2 ECHO: PB-770H ECHO: PB-770T INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment

More information

440 & 443 Skid Steer

440 & 443 Skid Steer Bobcat 440 & 443 Skid Steer THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF BOBCAT OR IT S SUCCESSORS. BOBCAT AND IT S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY OR ACCURACY

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 0GC Gas Concrete Saw Effective January, 09 0 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject to change

More information

Not for Reproduction ADVANCE PRODUCT SERVICE INFORMATION APSI NO: 101 DATE: AUGUST SERIES UTILITY ENGINE 130G00 OHV HORIZONTAL SHAFT

Not for Reproduction ADVANCE PRODUCT SERVICE INFORMATION APSI NO: 101 DATE: AUGUST SERIES UTILITY ENGINE 130G00 OHV HORIZONTAL SHAFT ADVANCE PRODUCT SERVICE INFORMATION APSI NO: 101 DATE: AUGUST 2014 SUBJECT: MODELS: 950 SERIES UTILITY ENGINE 130G00 OHV HORIZONTAL SHAFT This APSI provides basic servicing information in advance of the

More information

PISTON AND CONNECTING ROD

PISTON AND CONNECTING ROD 42 02 PISTON AND CONNECTING ROD 1. No.1 compression ring 2. No.2 compression ring 3. Oil ring Description Cylinder bore diameter Piston outer diameter (D1) Clearance between bore and piston Piston cooling

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List RZ60/603GC Gas Concrete Saw Effective January 1, 2018 2017 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List RZ60/603GC Gas Concrete Saw Effective January 1, 2016 2016 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List RZ60/603GC Gas Concrete Saw Effective January 1, 2016 2016 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject

More information

1.6L 4-CYL - VIN [E]

1.6L 4-CYL - VIN [E] 1.6L 4-CYL - VIN [E] 1993 Nissan Sentra 1993 NISSAN ENGINES 1.6L 4-Cylinder NX, Sentra * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES

More information

I. TWO-STROKE MECHANICAL EN- GINE PARTS

I. TWO-STROKE MECHANICAL EN- GINE PARTS I. TWO-STROKE MECHANICAL EN- GINE PARTS 1. UNIBLOCK ENGINES (AV520-600-750-125) a) INTRODUCTION Fig. 1 shows the short block. Fig. 2 shows an exploded view of the engine. As may be seen the momoblock is

More information

SERVICE DATA. CS-310 (Serial number : ) (Serial number : ) CHAIN SAW 01-30A-00 CS CONTENTS INTRODUCTION

SERVICE DATA. CS-310 (Serial number : ) (Serial number : ) CHAIN SAW 01-30A-00 CS CONTENTS INTRODUCTION 01-30A-00 CS-310 1 0 SERVICE DATA CHAIN SAW CS-310 (Serial number : 11000001-11999999) (Serial number : 12000001-12999999) INTRODUCTION We are constantly working on technical improvement of our products.

More information

G44B G40B G34B G29B G44BSS G40BSS G34BSS TWO (2) CYLINDER, AIR COOLED (AXIAL FAN) TWO (2) STROKE ENGINE RECOIL STARTER AVAILABLE)

G44B G40B G34B G29B G44BSS G40BSS G34BSS TWO (2) CYLINDER, AIR COOLED (AXIAL FAN) TWO (2) STROKE ENGINE RECOIL STARTER AVAILABLE) SPECIFICATIONS G44B G40B G34B G29B G44BSS G40BSS G34BSS MODEL ST ANDARD MODEL SS MODEL TYPE TWO (2) CYLINDER, AIR COOLED (AXIAL FAN) TWO (2) STROKE ENGINE DISPLACEMENT (ee) 432 394 338 292 432 394 338

More information

World Formula TECH MANUAL

World Formula TECH MANUAL World Formula TECH MANUAL Section 1 General Rules 1. Only stock Briggs & Stratton World Formula Model # 124435-8101 will be used in this class except as provided in this Tech manual. All parts will be

More information

SERVICE DATA TRIMMER/BRUSHCUTTER KIORITZ CORPORATION F-00 SRM-260 SRM-261 Series 1

SERVICE DATA TRIMMER/BRUSHCUTTER KIORITZ CORPORATION F-00 SRM-260 SRM-261 Series 1 10-25F-00 SRM-260 SRM-261 Series 1 1 SERVICE DATA TRIMMER/BRUSHCUTTER SRM-260 (Serial number : 05001001~05999999) SRM-260S (Serial number : 05001001~05999999) SRM-260U (Serial number : 05001001~05999999)

More information

TWO STAGE SNOW ENGINE SERVICE MANUAL

TWO STAGE SNOW ENGINE SERVICE MANUAL RESIDENTIAL PRODUCTS TWO STAGE SNOW ENGINE SERVICE MANUAL LC175FDS (265cc) LC180FDS (302cc) About this Manual This service manual was written expressly for Toro service technicians. The Toro Company has

More information

SERVICE MANUAL SUPPLEMENT

SERVICE MANUAL SUPPLEMENT 01-34C-00 CS-352 1 0 SERVICE MANUAL SUPPLEMENT CHAIN SAW ECHO: CS-352 (Serial number : 11000001-11999999) (Serial number : 12000001-12999999) (Serial number : 13000001-13999999) INTRODUCTION We are constantly

More information

Chapter 5 Part B: Ignition system - transistorised type

Chapter 5 Part B: Ignition system - transistorised type 5B 1 Chapter 5 Part B: Ignition system - transistorised type Contents Coil - testing........................................... 9 Distributor - overhaul..................................... 7 Distributor

More information

Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS

Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS connecting rods are marked for reassembly. 3. Thoroughly clean and inspect all components. Coat pin with engine oil and heat piston to 158-176 F (70-80 C). Pin should push fit with thumb pressure through

More information

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical)

2001 Chevrolet Metro LSi ENGINES 1.3L 4-Cylinder - Metro & Firefly (Canadian) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 3: Exploded View Of Timing Belt & Components (Typical) Fig. 4: Aligning Timing Marks 6. Loosen the timing belt tensioner bolt and the stud. 7. After pushing up the tensioner plate completely with

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 613GC Gas Concrete Saw Effective January 1, 2010 SERVICE ITEMS 613GC Gas Concrete Saw Above 71700 Gas Saw Service Tool Kit, includes all items shown above $668.00

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 680GC Petrol Concrete Saw Serial numbers starting with 967 & 977 Effective January 1, 2011 TABLE OF CONTENTS 680GC Petrol Concrete Saw ITEM DESCRIPTION KEY PAGE

More information

SERVICE DATA CHAIN SAW ECHO: CS-500ES STAGE MODEL. (Serial number : and after) CONTENTS INTRODUCTION

SERVICE DATA CHAIN SAW ECHO: CS-500ES STAGE MODEL. (Serial number : and after) CONTENTS INTRODUCTION 01-50D-01 1 0 SERVICE DATA CHAIN SAW ECHO: STAGE MODEL (Serial number : 37000001 and after) INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data,

More information

AJV8 Engine Assembly. AJV8 Engine Assembly

AJV8 Engine Assembly. AJV8 Engine Assembly AJV8 Engine Assembly Contents Cylinder Block Dowels, Plugs and Pipes 2 4 Crankshaft Bearing and Cylinder Bore Dimensions 5 9 Bearing Measuring 6 Engine Dimensions and Codes 6 7 Main Bearing Selection Chart

More information

SERVICE DATA PPF-2100 PPT-2100 PPT-2400 PPFD-2400 POWER PRUNER 17-21C-00 INDEX. with new gear case INTRODUCTION CONTENTS

SERVICE DATA PPF-2100 PPT-2100 PPT-2400 PPFD-2400 POWER PRUNER 17-21C-00 INDEX. with new gear case INTRODUCTION CONTENTS 17-21C-00 1 1 SERVICE DATA POWER PRUNER with new gear case INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject

More information

1999 Acura SLX. Fig. 6: Identifying Piston & Connecting Rod Size Courtesy of ISUZU MOTOR CO.

1999 Acura SLX. Fig. 6: Identifying Piston & Connecting Rod Size Courtesy of ISUZU MOTOR CO. 3. Check cylinder bore to determine piston-to-cylinder clearance. Clearance should be within specification. See PISTONS, PIN & RINGS table under ENGINE SPECIFICATIONS. Fig. 6: Identifying Piston & Connecting

More information

2.2L 4-CYL - VIN [S]

2.2L 4-CYL - VIN [S] 2.2L 4-CYL - VIN [S] 1994 Toyota Celica 1994 ENGINES Toyota 2.2L 4-Cylinder Celica NOTE: For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article

More information

HKS 700E. Service Manual June Ver. 2.04

HKS 700E. Service Manual June Ver. 2.04 HKS 700E Service Manual 009 June Ver..04 HKS CO.,LTD 78 KITAYAMA FUJINOMIYA SHIZUOKA JAPAN 48-09 TEL +8(0)544-54-78 FAX +8(0)544-54-40 hks_aviation@hks-power.co.jp http://www.hks-power.co.jp/hks_aviation/

More information

D - ADJUSTMENTS - 4-CYL

D - ADJUSTMENTS - 4-CYL D - ADJUSTMENTS - 4-CYL 1993 Toyota Celica 1993 ENGINE PERFORMANCE Toyota 4-Cylinder On-Vehicle Adjustments Celica ENGINE MECHANICAL Before performing any on-vehicle adjustments to fuel or ignition systems,

More information

660GC SERVICE MANUAL

660GC SERVICE MANUAL 660GC SERVICE MANUAL SECTION SECTION TITLE PAGE NUMBER SERVICE MANUAL USE 2 1 TOOLS 3 2 SAW SPECIFICATIONS 4 3 SERIAL NUMBER LOCATION 5 4 SPARE PARTS DIAGRAMS (TORQUE SPECS & LOCTITE APPLICATION) 6 5 AIR

More information

INTRODUCTION. Reference No S-01 REVISED:

INTRODUCTION. Reference No S-01 REVISED: 10-21S-01 GT-225, SRM-225 1 1 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice.

More information

COLT 2310, 2510, AND 2712 COM PACT TRACTORS CHAPTER 9 TROUBLESHOOTING AND ANALYSIS

COLT 2310, 2510, AND 2712 COM PACT TRACTORS CHAPTER 9 TROUBLESHOOTING AND ANALYSIS COLT 2310, 2510, AND 2712 COM PACT TRACTORS CHAPTER 9 TROUBLESHOOTING AND ANALYSIS 9-A-1 UPON RECEIVING ANENGINE FORRE- PAIR. Learn the history of the unit from the customer. While the customer is present

More information

680ES SERVICE MANUAL

680ES SERVICE MANUAL 680ES SERVICE MANUAL 1 TABLE OF CONTENTS 680ES SERVICE MANUAL SECTION SECTION TITLE PAGE NUMBER SERVICE MANUAL USE 2 1 TOOLS 5 2 POWER CUTTER SPECIFICATIONS 6 3 SERIAL NUMBER LOCATION 7 4 SPARE PARTS DIAGRAM

More information

SERVICE DATA. SRM-230U (Serial number : ~ ) SRM-231U (Serial number : ~ ) TRIMMER/BRUSHCUTTER KIORITZ CORPORATION

SERVICE DATA. SRM-230U (Serial number : ~ ) SRM-231U (Serial number : ~ ) TRIMMER/BRUSHCUTTER KIORITZ CORPORATION 10-22E-00 SRM-230 SRM-231 Series 1 1 SERVICE DATA TRIMMER/BRUSHCUTTER SRM-230 (Serial number : 05001001~05999999) SRM-230S (Serial number : 05001001~05999999) SRM-230U (Serial number : 05001001~05999999)

More information

F SERIES STARTER. thrust washer. STARTER DISASSEMBLY. to the starter motor. Remove cup. Remove starter pulley and spring. USE

F SERIES STARTER. thrust washer. STARTER DISASSEMBLY. to the starter motor. Remove cup. Remove starter pulley and spring. USE STARTER DISASSEMBLY Remove retainer ring, pinion stop washer, pinion spring and pinion gear from helix. Remove starter pulley and spring. USE CAUTION WHEN REMOVING SPRING. Remove three screws holding the

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 680ES Gas Concrete Saw Effective July, 0 I TABLE OF CONTENTS 680ES Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC Gas Saw Service Items n/a Starter Assembly

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 613GC Gas Concrete Saw Effective January 1, 2011 TABLE OF CONTENTS 613GC Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 613GC Gas Saw Service Items n/a ii Starter

More information

This file is available for free download at

This file is available for free download at This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing

More information

BOTTOM END SERVICE TOOLS SERVICE PRODUCTS ENGINE, CVT AND GEARBOX Subsection 10 (BOTTOM END)

BOTTOM END SERVICE TOOLS SERVICE PRODUCTS ENGINE, CVT AND GEARBOX Subsection 10 (BOTTOM END) BOTTOM END SERVICE TOOLS Description Part Number Page CRANKCASE SUPPORT MAG/PTO... 529 036 031... 151 CRANKSHAFT LOCKING BOLT... 529 035 617... 154 DRIVE SHAFT OIL SEAL INSTALLER... 529 036 028... 143

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 680ES Gas Concrete Saw Effective July 1, 2015 I TABLE OF CONTENTS 680ES Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC Gas Saw Service Items n/a 1 Starter Assembly

More information

OWNER S MANUAL G620PU-1 MODEL: G620PU WARNING 848H4893A3 (704)

OWNER S MANUAL G620PU-1 MODEL: G620PU WARNING 848H4893A3 (704) 848H4893A3 (704) OWNER S MANUAL MODEL: G620PU G620PU-1 WARNING Do not modify any parts of the engine. This engine is designed to be used to Radio controlled products. In case any modification by customer,

More information

Performer Series Carburetor Rebuild Kit Catalog #1477 Models

Performer Series Carburetor Rebuild Kit Catalog #1477 Models Please read these instructions carefully before attempting to rebuild your carburetor. Make sure to refer to your carburetor Owner s Manual for further information if need be. If you have any questions

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 680ES Gas Concrete Saw Effective January 1, 2017 I TABLE OF CONTENTS 680ES Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC Gas Saw Service Items n/a 1 Starter

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 680GC Gas Concrete Saw Serial numbers starting with 967 & 977 Effective July 1, 2015 I TABLE OF CONTENTS 680GC Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 680GC Petrol Concrete Saw Serial numbers starting with 967 & 977 Effective January 1, 2013 I TABLE OF CONTENTS 680GC Petrol Concrete Saw ITEM DESCRIPTION KEY

More information

SINGLE STAGE SNOW ENGINE SERVICE MANUAL

SINGLE STAGE SNOW ENGINE SERVICE MANUAL RESIDENTIAL PRODUCTS SINGLE STAGE SNOW ENGINE SERVICE MANUAL LC154FS / LC154FDS (87cc) About this Manual This service manual was written expressly for Toro service technicians. The Toro Company has made

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 633GC / 633F4 Gas Concrete Saws Effective January 1, 20167 TABLE OF CONTENTS 633GC / 633F4 Gas Saws ITEM DESCRIPTION KEY PAGE 633GC / 633F4 Gas Saw Service Items

More information

680GC SERVICE MANUAL ICS- Blount Inc Specifications and pricing are subject to change without notice. P/N REV12Sep2012

680GC SERVICE MANUAL ICS- Blount Inc Specifications and pricing are subject to change without notice. P/N REV12Sep2012 680GC SERVICE MANUAL i TABLE OF CONTENTS SECTION SECTION TITLE PAGE NUMBER SERVICE MANUAL USE 2 1 TOOLS 3 2 SAW SPECIFICATIONS 4 3 SERIAL NUMBER LOCATION 5 4 SPARE PARTS DIAGRAM (TORQUE AND LOCTITE ) 6

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 680GC Gas Concrete Saw Serial numbers starting with 967 & 977 Effective January 1, 2019 I TABLE OF CONTENTS 680GC Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC

More information

MANUAL INDEX. Page 1. LEOPARD 125cc ENGINE DISASSEMBLY CRANKSHAFT DISASSEMBLY/ ASSEMBLY CRANKSHAFT DISASSEMBLY 8

MANUAL INDEX. Page 1. LEOPARD 125cc ENGINE DISASSEMBLY CRANKSHAFT DISASSEMBLY/ ASSEMBLY CRANKSHAFT DISASSEMBLY 8 MANUAL INDEX Page 1. LEOPARD 125cc ENGINE DISASSEMBLY 1 2. - CRANKSHAFT DISASSEMBLY/ ASSEMBLY 8 2.1- CRANKSHAFT DISASSEMBLY 8 2.2- CRANKSHAFT ASSEMBLY 10 3. LEOPARD 125cc ASSEMBLY 13 4. - CHECK CYLINDER

More information

Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical condition is okay.

Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical condition is okay. Page 1 of 11 ARTICLE BEGINNING INTRODUCTION Introduction information not applicable. ENGINE MECHANICAL Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical

More information

3. INSPECTION/ADJUSTMENT

3. INSPECTION/ADJUSTMENT 3 SERVICE INFORMATION...3-0 FINAL REDUCTION GEAR OIL...3-7 MAINTENANCE SCHEDULE...3-2 DRIVE BELT...3-7 FUEL FILTER...3-3 BRAKE SHOE...3-8 THROTTLE OPERATION...3-3 BRAKE ADJUSTING NUT...3-8 AIR CLEANER...3-4

More information

Briggs & Stratton Animal TECH MANUAL Version 1.6 Section 1 General Rules cannot Section 2 Required Modifications Section 3 Allowable Modifications

Briggs & Stratton Animal TECH MANUAL Version 1.6 Section 1 General Rules cannot Section 2 Required Modifications Section 3 Allowable Modifications Briggs & Stratton Animal TECH MANUAL Version 1.6 updated 2/ 7 / 2011 Section 1 General Rules 1. Only stock Briggs & Stratton Animal # 124332-8201and 124332-8203 - 01engine will be allowed in this class.

More information

lbs sq. Camshaft bush ID 0.5 ± Clearance bush to camshaft ±

lbs sq. Camshaft bush ID 0.5 ± Clearance bush to camshaft ± GENERAL Cubic capacity 347 C.C. Stroke 93 mm. / 3.6614 Cylinder bore Compression ratio Max compression at kick starter speed 2 23 /32 = 2.7187 ± 0.0005 (Re-bore to + 0.02 when wear exceeds 0.008 ). Note:

More information

90 Y-12 Youth. Model Number A2005H4B2BUSR (Red) Model Number A2005H4B2BUSZ (Cat Green) Illustrated Parts Manual

90 Y-12 Youth. Model Number A2005H4B2BUSR (Red) Model Number A2005H4B2BUSZ (Cat Green) Illustrated Parts Manual 90 Y-12 Youth Model Number A2005H4B2BUSR (Red) Model Number A2005H4B2BUSZ (Cat Green) Illustrated Parts Manual 2005 TABLE OF CONTENTS 2005 ATV 90 Y-12 Youth Red (Model No. A2005H4B2BUSR) Cat Green (Model

More information

SERVICE DATA CHAIN SAW ECHO: CS-280WES STAGE MODEL. (Serial number : and after) CONTENTS INTRODUCTION. Reference No B-00 ISSUED:

SERVICE DATA CHAIN SAW ECHO: CS-280WES STAGE MODEL. (Serial number : and after) CONTENTS INTRODUCTION. Reference No B-00 ISSUED: 00-27B-00 1 0 SERVICE DATA CHAIN SAW ECHO: STAGE MODEL (Serial number : 37000001 and after) INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data,

More information

Operation and Maintenance Instructions for the RAPTOR 178

Operation and Maintenance Instructions for the RAPTOR 178 WWW.SKYTOY.COM Operation and Maintenance Instructions for the RAPTOR 178 See www.skytoy.com for updates and service bulletins. 2/1/2011 1. Parts Schematic:... 3 2. Muffler Assembly Diagram:... 4 3. Muffler

More information

ILLUSTRATED PARTS BOOK Walk Behind Mower MODEL: SM2010

ILLUSTRATED PARTS BOOK Walk Behind Mower MODEL: SM2010 ILLUSTRATED PARTS BOOK Walk Behind Mower MODEL: SM2010 Table of Contents Top Level Assembly...3 Engine Top Level Assembly..4 Handle Assembly 5 Frame Assembly.6 Blade Assembly...7 Wheel Assembly.8 Warning

More information

00-36A-04 CS-350T, CS-350TES, CS-350WES 1

00-36A-04 CS-350T, CS-350TES, CS-350WES 1 00-36A-04,, 1 0 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications,

More information

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13)

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13) 13 Engine-Crankshaft, Cylinder block (Page GR-13) Engine, disassembly and assembly 10-222 A/21 guide from 10-222 A support tool, modifying Ribbed belt, removing and installing Semi-automatic toothed belt

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 680ES Petrol Concrete Saw Effective January, 08 I TABLE OF CONTENTS 680ES Petrol Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC Petrol Saw Service Items n/a Starter

More information

OWNER S MANUAL G620PU-1 MODEL: G620PU WARNING 848H5693A3 (208)

OWNER S MANUAL G620PU-1 MODEL: G620PU WARNING 848H5693A3 (208) 848H5693A3 (208) OWNER S MANUAL MODEL: G620PU G620PU-1 WARNING Do not modify any parts of the engine. This engine is designed to be used to Radio controlled products. In case any modification by customer,

More information

21-21H-00 PB-2100,PB-2155,PB-2200SI 1

21-21H-00 PB-2100,PB-2155,PB-2200SI 1 21-21H-00 PB-2100,,PB-2200SI 1 2 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice.

More information

Drawing A Crankcase 041 AV SCS

Drawing A Crankcase 041 AV SCS Drawing A Crankcase 1 Drawing A Crankcase Reference Item number Qty Description 1 1110 020 2105 1 Crankcase 2-5, 9, 10, 12 2 9371 470 3120 2 Cylindrical pin 6x20 3 9048 216 1010 8 Pan head screw M5x18

More information

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE

MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE 1. Disconnect negative battery cable. Drain cooling system. Remove front strut bar and strut brackets, if equipped. 2. Disconnect Intake Air Temperature (IAT) sensor harness connector. Remove air cleaner

More information

OVERHAUL MANUAL 28/09/05 mod. A 1 MAN-044 ING

OVERHAUL MANUAL 28/09/05 mod. A 1 MAN-044 ING OVERHAUL MANUAL 28/09/05 mod. A 1 INDEX Page 1. - PARILLA X30 125cc RL TaG ENGINE DISASSEMBY 1 2. - CRANKSHAFT DISASSEMBLY/ ASSEMBLY 10 2.1- CRANKSHAFT DISASSEMBLY 10 2.2- CRANKSHAFT ASSEMBLY 12 3. - PARILLA

More information

Illustrated Parts List

Illustrated Parts List FORM MS 4183 10/31/2006 REPLACES FORM MS 9748 7/1997 FILE IN SECT. 2 OF SERVICE MANUAL 290700 Illustrated Parts List Model Series 290700 TYPE NUMBERS 0100, 0102, 0106, 0107, 0108, 0333, 0402, 0410. TO

More information

365-SUB Engine : Engine Assembly 365-SUB [1/1] Page 1 of 5

365-SUB Engine : Engine Assembly 365-SUB [1/1] Page 1 of 5 Page 1 of 5 1 951-11012 Bolt 2 951-11054 Valve Cover 2 951-11054 1 Valve Cover 3 731-07059 Breather Hose 4 726-04101 Hose Clamp 6 N/A 1 Intake Valve Spring Seat 7 751-11124 Pivot Locking Nut 7 751-11124

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 680GC Gas Concrete Saw Serial numbers starting with 967 & 977 Effective January 1, 2018 I TABLE OF CONTENTS 680GC Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC

More information

ENGINE MECHANICAL EM SECTION CONTENTS

ENGINE MECHANICAL EM SECTION CONTENTS ENGINE MECHANICAL EM SECTION CONTENTS INTAKE MANIFOLD...EM-2 Component Parts Location...EM-2 Removal and Installation...EM-3 Inspection...EM-3 EXHAUST MANIFOLD...EM-4 Component Parts Location...EM-4 Removal

More information

SXLAO Chain Saw UT Page 1 of 21 Carburetor Chamber

SXLAO Chain Saw UT Page 1 of 21 Carburetor Chamber SXLAO Chain Saw UT-10045 Page 1 of 21 Carburetor Chamber SXLAO Chain Saw UT-10045 Page 2 of 21 Carburetor Chamber 1 59274 1 GASKET- Spacer 2 59718 1 SPACER 3 63260A 1 RETAINER- Reed valve 4 63253 1 SEAT-

More information

XL12 Chain Saw UT Page 1 of 21 Carburetor Chamber

XL12 Chain Saw UT Page 1 of 21 Carburetor Chamber XL12 Chain Saw UT-10080 Page 1 of 21 Carburetor Chamber XL12 Chain Saw UT-10080 Page 2 of 21 Carburetor Chamber 1 59274 1 GASKET- Spacer 2 59718 1 SPACER 3 63260A 1 RETAINER- Reed valve 4 63253 1 SEAT-

More information

Illustrated Parts List

Illustrated Parts List FORM MS 0670 3C 8/2001 REPLACES FORM MS 0670 2Q 11/2000 FILE IN SECT. 2 OF SERVICE MANUAL Illustrated Parts List Model Series TYPE NUMBERS 0042 through 1256. For Use On Engines Built Before Date Code 01070100.

More information

RIDING PRODUCT ENGINE SERVICE MANUAL

RIDING PRODUCT ENGINE SERVICE MANUAL RESIDENTIAL PRODUCTS RIDING PRODUCT ENGINE SERVICE MANUAL LC1P92F (452cc) About this Manual This service manual was written expressly for Toro service technicians. The Toro Company has made every effort

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION Page 1 of 11 REMOVAL & INSTALLATION TIMING BELT Tips Click a link to view tip Tech1 Question: Timing problems P0340 Tech1 Question: 2.2 TIMING PROBLEMS - RESOLVED Removal Tips Click a link to view tip

More information

REEDSTER 125cc. versions: F1 - F2 - F3 - F4 OVERHAULING MANUAL

REEDSTER 125cc. versions: F1 - F2 - F3 - F4 OVERHAULING MANUAL REEDSTER 125cc versions: F1 - F2 - F3 - F4 OVERHAULING MANUAL 07/11/07 21/01/2009 1 INDEX Page 1. - REEDSTER 125cc ENGINE DISASSEMBLY 1 2. - CRANKSHAFT DISASSEMBLY / ASSEMBLY 13 2.1 - CRANKSHAFT DISASSEMBLY

More information

Illustrated Parts List to

Illustrated Parts List to Illustrated Parts List Model Series TYPE NUMBERS 0111 through 0199, 0200 through 0213, 0300 through 0353, 1345,1353, 2035 through 2073, 2135 through 2174, 4001 through 4090, 5001, 5005, 5006, 5035 through

More information

Transmission/Crankshaft/Crank Case

Transmission/Crankshaft/Crank Case R.Crank Case Crankshaft L.Crank Case 11-0 11. Transmission/Crankshaft/Crank Case Transmission/Crankshaft/Crank Case Service Information 11-1 Troubleshooting 11-2 Transmission 11-3 Crank Case Disassembly

More information

Replacement Parts & Accessories Price List

Replacement Parts & Accessories Price List Replacement Parts & Accessories Price List 613GC Petrol Concrete Saw Effective January 1, 2013 TABLE OF CONTENTS 613GC Petrol Concrete Saw ITEM DESCRIPTION KEY PAGE 613GC Petrol Saw Service Items n/a

More information

SERVICE DATA CHAIN SAW ECHO: CS-352ES STAGE MODEL. (Serial number : and after) CONTENTS INTRODUCTION

SERVICE DATA CHAIN SAW ECHO: CS-352ES STAGE MODEL. (Serial number : and after) CONTENTS INTRODUCTION 01-34D-01 1 0 SERVICE DATA CHAIN SAW ECHO: STAGE MODEL (Serial number : 37000001 and after) INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data,

More information

21-25F-00 PB-251, PB-255ES, ES-255ES 1

21-25F-00 PB-251, PB-255ES, ES-255ES 1 21-25F-00 PB-251,, ES-255ES 1 2 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice.

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before

More information

SERVICE DATA CHAIN SAW CS-450. (Serial number : and after) CONTENTS INTRODUCTION. Reference No B-01 REVISED: ISSUED:

SERVICE DATA CHAIN SAW CS-450. (Serial number : and after) CONTENTS INTRODUCTION. Reference No B-01 REVISED: ISSUED: 01-45B-01 1 0 SERVICE DATA CHAIN SAW (Serial number : 36000001 and after) INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower

More information

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza

1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza 1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST

More information

Illustrated Parts List

Illustrated Parts List FORM MS 2432 10/05/2004 REPLACES FORM MS 2432 4C 5/2002 FILE IN SECT. 2 OF SERVICE MANUAL Illustrated Parts List Model Series TYPE NUMBERS 0101 through 4516. TABLE OF CONTENTS Air Cleaner.........................

More information

Kid Sprint Engine Rules Briggs World Formula

Kid Sprint Engine Rules Briggs World Formula Kid Sprint Engine Rules Briggs World Formula 2017 Jr Sprint Engine Rules Briggs World Formula effective 2/1/2017. All parts must bebriggs & Stratton factory production parts unless otherwise noted in these

More information

695XL SERVICE MANUAL

695XL SERVICE MANUAL 695XL SERVICE MANUAL TABLE OF CONTENTS SECTION SECTION TITLE PAGE NUMBER SERVICE MANUAL USE... 3 1 TOOLS... 4 2 POWER CUTTER SPECIFICATIONS... 5 3 SERIAL NUMBER LOCATION... 6 4 SPARE PARTS DIAGRAM... 7

More information

3. INSPECTION/ADJUSTMENT

3. INSPECTION/ADJUSTMENT 3 3 INSPECTION/ADJUSTMENT SERVICE INFORMATION -------------------------------------------- 3-1 MAINTENANCE SCHEDULE ---------------------------------------- 3-2 FUEL LINE/FUEL FILTER -------------------------------------------

More information

INDEX INTRODUCTION. Reference No L-01 REVISED:

INDEX INTRODUCTION. Reference No L-01 REVISED: 12-21L-01 1 1 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications

More information

Illustrated Parts List

Illustrated Parts List FORM MS 2247 11/29/2004 REPLACES FORM MS 2247 10/05/2004 FILE IN SECT. 2 OF SERVICE MANUAL 286700 Illustrated Parts List Model Series 286700 TYPE NUMBERS 0102 through 4529. TABLE OF CONTENTS Air Cleaner.........................

More information

TECHNICAL DATA. COMPRESSION RATUI 9,5/1 WEIGHT ready to fly CONSUMPTION at 5400RPM 5,6litres/h POWER at 6200RPM

TECHNICAL DATA. COMPRESSION RATUI 9,5/1 WEIGHT ready to fly CONSUMPTION at 5400RPM 5,6litres/h POWER at 6200RPM VICTOR 1 SUPER This handbook aims to bring to the attention of key technical, functional and maintenance of your motor VICTOR 1. Read carefully the following pages, will be synonymous with safety, reliability

More information