INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Esther Beasley
6 years ago
Views:

1 Accessory Application Publication No. INSTALLATION INSTRUCTIONS LED HEADLIGHT P/N 08V71-HL4-A00 SXS1000M3/M3P/M5P Honda Dealer: Please give a copy of these instructions to your customer. MII Issue Date September 2015 PARTS LIST (1) (4) INSTALLATION CAUTION To prevent burns, allow the engine, exhaust system, radiator, etc., to cool before installing the accessory. NOTE: Disconnect the battery negative (-) cable before installing this accessory. The memory of the clock will be erased when you disconnect the battery. Reset the clock after reconnecting the battery. (2) Reinstall the removed parts on the vehicle and make sure that the wires and harnesses are not pinched. No. Description Qty (3) 1. Loosen the band as shown. <Right side> (1) Installation Instructions URL 1 (2) Right LED headlight 1 (3) Left LED headlight 1 (4) Headlight cap 4 LED HEADLIGHT SUB HARNESS Sold separately (1) No. Description Qty (1) LED Headlight sub harness 1 Loosen. BAND TORQUE CHART Refer to the Service Manual for the torque values of the removed parts. DUCT 2015 American Honda Motor Co., Inc. - All Rights Reserved. 1 of HL4-A001

2 2. Remove the vehicle s parts as shown. 4. Remove the clips as shown. <Left side> 3. Remove the front bumper as shown. 5. Remove the left front door as shown. FRONT BUMPER LEFT FRONT DOOR Remove the bolts as shown. Repeat on the right side. 2 of 7

3 6. Remove the left front mud guard as shown. 10. Remove the battery stay as shown. LEFT FRONT MUD GUARD BATTERY STAY 7. Remove the bolt as shown. 11. Remove the battery and battery cushion as shown. Disconnect the negative (-) cable first. BATTERY BATTERY CUSHION 8. Repeat on the right side. 9. Remove the front hood as shown. FRONT HOOD 3 of 7

4 12. Remove the filter cover as shown. Cover the duct with a shop towel to prevent debris from entering the duct. 15. Remove the connectors as shown. 2-PIN WATERPROOF CONNECTOR (Black) FILTER DUCT 6-PIN WATERPROOF CONNECTOR (Black) 16. Remove the clips as shown. 13. Remove the relay and fuse box as shown. RELAY FUSE BOX BATTERY CABLE 14. Remove the fuse holder and starter relay switch as shown. FUSE HOLDER STARTER RELAY SWITCH 4 of 7

5 17. Remove the front fender as shown. Cover the duct with a shop towel or similar to prevent debris from entering the duct. 19. Remove the clip and connector as shown. 3-PIN WATER PROOF CONNECTOR (Green) HEADLIGHT HARNESS DUCT 20. Repeat Steps 18 and 19 on the right side. 21. Remove the headlight harness as shown. HEADLIGHT HARNESS (Save) 18. Remove the cap as shown. <Left side> (Under side) 22. Remove the left headlight cover as shown. CAP 5 of 7

6 23. Remove the left headlight as shown. (Save) 25. Install the left LED headlight as shown. LEFT LED HEADLIGHT SPRING SPRING NUT NUT 24. Install the headlight caps on the left LED headlight as shown. LEFT LED HEADLIGHT HEADLIGHT CAP LEFT LED HEADLIGHT HEADLIGHT CAP Align. 6 of 7

7 26. Install the assembled left headlight cover in the reverse order of removal. 29. Install the clip and connector as shown. Repeat on the right side. ASSEMBLED LEFT HEADLIGHT 3-PIN WATERPROOF CONNECTOR (Black) LED HEADLIGHT SUB HARNESS 30. Install the caps and front fender in the reverse order of removal. Remove the covered shop towel or similar. 27. Repeat Steps 23 through 26 on the right side. 28. Install the LED headlight sub harness as shown. TAPE (Black) TAPE (Red) 31. Install the vehicle s parts in the reverse order of removal. Confirm that any wire harness is not caught or too tight. 32. Connect the negative (-) cable to the battery and check each light for function. 33. Check the LED headlight aim and adjust if necessary. LED HEADLIGHT SUB HARNESS 7 of 7

INSTALLATION INSTRUCTIONS

Accessory Application Publication No. INSTALLATION INSTRUCTIONS HORN MOUNT P/N 08Z77-HL4-A00 SXS1000M3/M3P/M5D/M5P Honda Dealer: Please give a copy of these instructions to your customer. MII 15262 Issue