ROLLER SHADING SYSTEMS

Transcription

1 ROLLER SHADING SYSTEMS

2 ROLLER SHADES A WORLD OF USES Roller shading systems provide an excellent way to control light and glare. Modern, sleek, high performance, and cost effective, our shading systems are aimed to directly address the needs of your clientele. Meeting Spaces Exterior Elevations Guest Rooms

3 ROLLER SHADES FABRICS Fabric selection is key! Fabtex offers a wide range of top notch fabrics with a color story that will amaze. Earth tones to vibrant hues, sheer to blackout, Fabtex has a fresh fabric solution for your unique spaces.

4 FEATURES AND BENEFITS OPTIMUM SOLAR CONTROL Features: Manual, motorized or crank operation Maintenance-free clutch system Lightweight fiberglass core yarns Polyester-core material yarns Wide range of openness capabilities Heat-sealed enclosed hem pocket Hidden aluminum hem bar Vinyl interconnect welded to fabric to attach fabric to tube Full range of systems options State-of-art motorized control systems Wide range of Specialty Products: Bottom up shades Arch & Triangle tops Stationary Screens & Panels Skylights Greenhouse Shapes Roman Shades Panel Glides Vertical Solar Vanes Benefits: Convenient one stop operation regardless of shade size Easy installation, no expensive adjustments required Reduced pull force, excellent stability, inherent fire-resistance Excellent value, competitively priced contemporary colors Excellent light and glare control Superb styling Decorative styling Allows for easy removal or replacement of materials-press-fit design Ceiling closures, fascias, pocket enclosures, side and sill channel Operate shade with maximum energy efficiency and flexibility Meet customer requirement for offering solutions for unusual window installations

5 FEATURES AND BENEFITS MANUAL AND MOTORIZED The Manual Shade 3 Sizes of clutch mechanisms for all window sizes and uses Lift and assist available Geared clutches lift with 30 lbs. with 6 lbs. pull force Non-Slip mechanism never needs adjustment Chain-driven steel standard (optionalplastic) Left & right control inside and outside mounting Without fascia standard (optional 3 or 4 fascia) Hembar heat-welded into hem pocket on 3 sides Vinyl fabric to tube interconnect The Motorized Shade 110 volt AC- Tubular thermal protected and UL listed. Motors are designed for constant torque and speed. 12V & 24V (low voltage) motors for shades up to 40 lbs Individual motor control by rocker switch. Toggle & Paddle styles available. White standard. Ivory is optional Motor Controls: Light, sun, temperature, and timer controls for interior applications. Wind sensors for exterior systems. Individual and multi shade group controls for groups and subgroups. Remote controls for up to 60 motors. Smart Line Systems for Computer Interface for complete systems control of groups and sub-groups of motors. Wall, ceiling, or side mount brackets

6 ROLLER SHADE DETAILS MANUAL SHADING 101 Let s go back to basics: a manual roller shade is a very simple affair when executed correctly. When structured in such a way where the components complement each other instead of fight one another, you have a solar shading system that is functional, beautiful, and will stand the test of time. You have shade that adds to the whole room package without detracting from it. The Clutch At the heart of every manual shade lies a clutched control mechanism. A proper roller shade clutch allows the shade to be positioned and held in place automatically as soon as the user releases the control chain. Our clutch system utilizes six heavy duty tension springs encased in specially formulated high density plastic to effect this automatic braking. The drive housing interlocks into the aluminum tube and covers the springs that rest on the inner core. Rotational force from the user is transferred through the chain drive, to the spring cams, releasing the spring tension and allowing the drive housing to rotate; thus moving the shade up or down. This design method is very simple, strong, and effective.

7 ROLLER SHADE DETAILS MANUAL CLUTCHES Design Our clutch systems come in two different forms. The first is rated for small to medium shades and the second is rated for medium to large shades. Both clutch systems utilize the same brackets, endcaps, fascia, and with even the same tubes. The biggest difference between the two clutches is design- the larger 30 pound clutch uses a larger chain drive gear to increase the leverage, and thus lessen the pull force required, to move shades of higher mass. PS20 Clutch A PS20 Clutch is a manual clutch rated at 20 pounds of lifting force. Designed to fit a 1.5 tube or a 2 tube using an adaptor, and used with 4 fascia this clutch is very versatile and can accommodate small to medium sized shading systems. PS30 Clutch A PS30 Clutch is a manual clutch rated at 30 pounds of lifting force. Designed to fit a 2 tube or a 2.5 tube using an adaptor, and used with 4 fascia, this clutch is very versatile and can accommodate medium to large sized shading systems. The HD version of this clutch accommodates a Pure Balance Mechanism for very large and heavy shades.

8 SHADE COMPONENTS TUBES Pure Shade tubes for manual clutch systems come in three sizes to accommodate shading systems of varying weights and sizes. 1.5 Aluminum Tube Used with PS20 Manual Clutch Systems for shades smaller than 72 wide, the 1.5 tube is made of T6 aluminum and has a wall thickness. 2 Aluminum Tube Used with PS20 Manual Clutch Systems for shades from 72 wide to about 120 wide, and as standard for a motorized shade system. The 2.0 tube is made of T6 aluminum with internal ribs for additional strength and rigidity. 2.5 Aluminum Tube This 2.5-inch tube is used with the PS30 Manual for large shades and the standard motorized shade system. It is made of T6 aluminum and has a inch wall thickness. For manual shades, it can be used with the Pure Balance mechanism. There is a spline opening built-in for attaching fabric.

9 ROLLER SHADE DETAILS MOUNTING AND BRACKETS Without Fascia Pure Shade brackets are universal and interchangeable; each bracket can be used on the clutch side or the idle side. Additionally, each bracket can be mounted inside the window frame (side mount), to the wall, or to the ceiling. Shown below are the mounting methods for non-fascia brackets. With Fascia A fascia or valance may be desired to give the manual roller shade installation a sleek finished look to compliment the decor. Pure Shade fascia is a snap-on aluminum valance that covers the shade and mounting hardware. The valances are available in an array of designer colors: white, bone, bronze and clear anodized. There also is a selection of custom colors. The fascia is designed to attach securely to the Pure Shade bracket system and are easy to maintain. The fascia brackets, like our standard brackets, are universal and interchangeable. Each can be used on the clutch side or the idle side. Each can be mounted inside the window frame (the side mount), to the wall or to the ceiling. Ceiling mount is shown below:

10 ROLLER SHADE DETAILS SHADE COMPONENTS FASCIA Fascia is an aluminum valance that is designed to cleanly snap onto specially designed shade mounting brackets. Designed to cover the shade roll and mounting hardware, shade fascia provides a sleek finished look. 4 box brackets mount to side, ceiling, or rear wall. Fascia is available in 3, 4, 5 and 7 extrusions for different shade systems: manual, motorized, dual tube, and dual motorized. Designed for medium to large shades and thicker tube diameters, the 4 square fascia, our most popular is shown at the right. The 4 fascia is available in: White, Bone, Bronze, Black and Brushed Aluminum. Available in custom colors and as fabric wrapped; we custom wrap the fabric in the same fabric as is used in the shade band. SIDE AND SILL CHANNEL Channels are a way to capture the edge of the fabric, and guide it along a wall of window mullion. Mainly used in installations requiring blackout conditions, side and sill channels can also be used on a door to keep a shade in place while maintaining its ability to operate easily. Our two piece design snap together to create a clean finish absent of any screw heads or button cap covers. These channels can be mounted to the face of a wall or window mullion, or along the inside edge of the window frame. Dimensions are 2.25 inches by 1 inch. Standard designer finishes are white, bone, bronze, black and clear anodized. Custom colors also are available for an additional charge.

11 ROLLER SHADE DETAILS 5 INCH FASCIA SYSTEM Able to accommodate dual shades or a single large shade, our new 5 fascia system offers the ultimate in flexibility by allowing a single size fascia to cover more than one shade type. Its durable elegance offers robust hardware with clean aesthetics. This versatile fascia system provides for reverse roll conditions and the ability to use a matching length of fascia along the back side of the shade to further reduce light penetration when blackout is desired. Single Shade Configuration Used for large shades, generally motorized, the single shade configuration shown enable much longer shade band drops. Maximum shade widths can reach 192 wide, and with proper fabric selection, maximum drop lengths can get to 300 long. Manual components are shown, but to utilize the full capacity of this 5 inch system, motorization is required. Brackets allow ceiling, wall, or side mount capabilities. Bracket end caps are optional Dual Shade Configuration A step beyond the capabilities of our Dual Lite system, the 5 inch fascia system can handle a larger shade tubes and can therefore fit large windows and large shade band requirements. Band length will be more limited in the dual configuration as compared to the single detailed above. Maximum shade widths can reach 120 wide, and with proper fabric selection, maximum drop lengths can get to 120 long. components are shown, but to utilize the full capacity of this 5 inch system, motorization is required. Brackets allow ceiling, wall, or side mount capabilities. Bracket end caps are optional

12 ROLLER SHADE DETAILS THE SHADE GUARDIAN Invented and Patented by an industry veteran, the Shade Guardian is a revolutionary device designed to protect manual chain operated roller shading systems from general misuse/abuse and prolong their lifespan. Torn fabric, broken clutches, snapped idle ends; all signs of mistreated shades and something facility maintenance professionals are all too familiar with and something they spend a great deal of time repairing. The Shade Guardian attaches to the clutch side of the shade and drastically decreases room unavailability due to shade maintenance issues. Able to be easily installed with new shade or retrofitted to existing, the Shade Guardian is a simple and cost effective way to save the shades in any high traffic facility. DEFENSE BY DESIGN The number one cause of damaged and broken roller shading systems is user abuse. In a commercial environment, window treatments are used by people who are either not familiar with the operation of a roller shade, or let s face it, just plain don t care. These users will grab the control chain and give it a yank expecting the shade to run up or down the window in one fell swoop. This action is all fine and good until the upper or lower limits of the shade are reached and instead of gently fitting into place and coming to a stop, the stop ball slams into the clutch. Depending upon the design of the clutch and size of the shade, this repeated abuse can be withstood for a time, but at some point the ball stop breaks the lower guard of the clutch and rams up into the geared mechanism. Usually this results in the shade jamming into a useless a fixed position. Thus resulting in a call to maintenance; and a room out of service which can cost hundreds of dollars! The Shade Guardian changes this scenario by giving that stop ball a cushioned place to be captured. Breakage happens when all the mass of a quickly rotating shade is required to come to an immediate halt. We ve fixed this by building a patented spring loaded pocket where the ball can be captured, brought to a gentle halt, and returned to a resting spot. Available in White, Black, and soon Grey, the Shade Guardian will change the way your maintenance crews look at window shading forever. Call your Fabtex Concierge today for more details and a demonstration.

13 ROLLER SHADE DETAILS MOTORIZED OPTIONS Motorized Roller Shades are the most advanced and cost effective way to control interior environments for optimum energy efficiency and occupant comfort. In addition to eliminating the need to manually adjust heavy or hard-to-reach window coverings Motorized Shades provide privacy while controlling sunlight, glare and UV rays. Another benefit of motorization in a public setting is the minimization of maintenance. Manual shades require a physical touch and can therefore be operated improperly and even abused, leading to greater levels of wear and tear. On the other hand, a motorized shade is never touched by the user as its operation occurs across the room by pressing a button on a wall or a remote. It is because of this simple dynamic, motorized shades tend to last two to three times longer than their manual counterparts. Taken to a greater degree, motorized shades connected to a central system not only reduce loads on HVAC and increase building efficiency, but add a touch of elegance and luxury to your guest s experience. Imagine a non-occupied guest room: freshly cleaned, lights are off, thermostat is set to minimum levels, and windows coverings are closed to both thermally insulate and protect the room from harsh UV rays. Now, as a guest checks in, a button at the main desk is pressed that prepares the room for guest entry; lights come up, window coverings open to provide optimum views, and air conditioning comes on as the thermostat brings the room up to optimum comfort levels. Every space has different needs, requirements, and goals. For that reason alone, there is no one size fits all motor, but there is a motor to fit your specific application Standard AC Hardwired Motor The basic workhorse of the line, our standard motor boasts a 5 wire configuration and built in parallel wiring capability. Best suited to new construction this motor runs and is switched purely off 110VAC. All switches are hardwired directly to the motor or group of motors they control. Pros: Economically priced for motors and switches. Smooth, quiet operation. Great choice for new building projects seeking basic, no-frills motorized shading systems. Cons: Requires all connections to be hardwired. All wiring is high voltage; 110VAC. Plug-in AC Motor with Wireless Controls Perhaps the most versatile and popular in the line, our RTM motor series combines simple, plug-in capability, with the versatility of wireless, place anywhere controls. A good choice when power (a wall outlet) is easily obtained or already existing. Pros: Smooth, quiet operation. Utilizes a standard 110VAC plug. Wireless controls- remotes and wall switches available. Good choice for retrofitting existing windows. Cons: Control range, feet. Not a good choice for large groups of motors. Requires 110VAC power.

14 ROLLER SHADE DETAILS MOTORIZED OPTIONS Battery Motor with Wireless Controls A popular variant of the RTM line, our battery powered motors are designed to be completely stand-alone devices. Each features a Lithium-ion Battery pack built into the motor itself. Simply install the shade into the window pocket with the motor, and the controls are 100% wireless. Charge the battery via a wall charger (similar to a cell phone) or via a small solar panel installed into the window between the shade header and the glass. Pros: Zero wiring required! Excellent choice for retrofitting existing windows in existing buildings. The solar option provides for true off-the-grid technology with zero wiring required! Cons: Control range, feet. AC Motor with Low Voltage Wired Controls An excellent choice for new projects with a bit of preplanning for wiring. These are smooth, quiet, and powerful motors. Can be setup to be plug-in or hardwired to a junction box with a switch for master power cutoff. Separate low voltage cable can be run from motor to any low voltage switch location. One switch can control any number of motors grouped together. Pros: Smooth, quiet operation, and powerful. Great choice for new building projects. Control wiring is low voltage. Cons: Requires AC power to each motor and low voltage wire runs to all controls. AC Motor with Digital System Integration The premier choice for full building automation controls and system integration. From full sun and daylight management to integrated wall switches and sun sensors. These are smooth, quiet, and powerful motors. Can be setup to be plug-in or hardwired to a junction box with a switch for master power cutoff. Separate low voltage cable can be run from motor to any low voltage switch location. One switch can control any number of motors grouped together. Pros: Full building control is achieved using our own Digital Interface, or through any robust building management system, back net controls, or lighting control system via RS-232, RS-485, and dry contact. Increases occupant comfort and building environmental efficiency. Cons: Requires 110VAC power to each motor and a low voltage CAT-5 network across the motor system.

15 ROLLER SHADE DETAILS MEASURING AND INSTALLATION Standard Deductions Fabric deductions are necessary to allow room for the clutch, idle end and brackets. Fabric deductions will vary based on the shade options selected and the mounting brackets used. Standard Fabric Deductions: Left Side 3/4 Right Side 3/4" An additional 1/8 inch overall deduction is made from the fascia on an inside mounted shade. This small deduction ensures the fascia will fit into place smoothly and not gouge the inside edges of the window pocket Preventing Light Gap Normally there is a light gap between the fabric edge and the side wall of the window opening but in most installations not requiring total blackout, the light leakage is not significant. However, the gap between the edge of the fabric band and side wall of the window opening can become an issue when it is larger than the depth of the window frame itself, thus allowing direct sunlight to pass. The way to eliminate this light gap is to install side channels or switching to an outside mount configuration and increasing the width of the shade by 2 inches on both sides. Speak with a Fabtex expert to determine the best solution for your specific needs. Installation Utilizing all of the proper safety gear; gloves, goggles, boots, and proper clothing, review the shade package contacts. Next, select the proper fastener type based upon the structure and composition of the mounting surface. Once selected, mount the shade brackets. Ensure they are secure and slide the roller shade into place, idle end first. Compress the idle end, lift up the clutch end, and set into the bracket, allowing it to set and catch the clutch tabs. If fascia is included, snap it securely into the brackets. Finally install the chain holddown and evaluate for proper operation. For more detailed instaructions on the specific details of your project s product, contact the Fabtex Installation Department. Or visit us online at

16 ROLLER SHADE DETAILS CARE AND CLEANING Operational Care Roller shades are durable window treatments but are still susceptible to breakage from abuse. Always exercise care when raising or lowering manual shades. Larger shades will require more effort and smaller ones less so. Always raise and lower in a smooth continuous fashion. Jerking on the chain in hard hurried motion will lead to damage and eventually breakage of the roller mechanisms. If the lift chain suddenly become more difficult than usual to pull, stop immediately and inspect the mechanism located at the top of the window. Ensure it is free of any obstructions, including dislodged fascia, foreign objects, or fabric that has telescoped across the width of the shade. Maintenance Shading components are made to withstand a lifetime of use with proper care and use. A regular inspection and light maintenance schedule is recommended. Schedule inspections more frequently for heavily used shades. Fabtex, your shading professionals can recommend specific spare parts to support a maintenance routine. On larger and motorized shade, there may be heavy duty coupling and bearings that should be inspected and lightly lubed from time to time. Take care when using any lubricants to use very small amounts as the oils can quickly and permanently stain some of the lighter decorative fabrics. Cleaning The most effective cleaning is accomplished with a light vacuuming. Use a vacuum hose extension coupled to a soft bristle brush. Ensure the bristle brush is clean and the vacuum motor is on low. Gently brush the surface of the fabric with the brush to loosen and suck up any dust. Where a vacuum is not available, a regular feather dusting can perform the same cleaning. In heavily soiled areas, a damp microfiber towel can be used to remove excess debris. Harsh cleaning chemicals should never be used as they can damage the surface of the fabric, destroying the UV protectants. It is also recommended the header area containing the roll mechanism is vacuumed to remove and accumulated cobwebs and dust bunnies. In areas where air flow is present, the window pockets will over time accumulate a layer of dirt and debris that can negatively affect shade performance.

17 ROLLER SHADE DETAILS LIMITED WARRANTY Fabtex, Inc. ( Fabtex ) warrants its shades and products from the date of shipment to be free from defects in materials and workmanship under normal and proper use as follows: Hardware: Warranted for 10 years from date of shipment. Bead chain is not warranted Shade Cloth: Warranted to be fit for its intended use. Interior is 10 years. Exterior is 5 years Motors: Warranted for 5 years from date of shipment Electronics and Electrical Accessories: Warranted for 1 year from date of shipment Fabtex s only obligation shall be to repair or replace defective equipment, which does not conform to the warranty. Fabtex shall not be liable for any injury, loss or damage, direct or consequential, arising out of the use of, or the inability to use the equipment. Before using, Buyer and/or the ultimate User shall determine the suitability of the project for its intended use, and User assumes all risks and liability in connection therewith. The articles that are replaced pursuant to the terms of this warranty shall be retained by Fabtex, and the User is responsible for any freight costs related to the repair or replacement. The foregoing warranty is excusive and in lieu of all other warranties of quality, whether written, oral or implied (including any other warranty of merchantability or fitness or purchase). The following are exclusions from warranty: If the product has been opened, dismantled or returned with clear evidence of abuse or other damage. If usage, adaptation or installation are not in accordance with our installation and operating instructions. If our written specifications are not properly applied by the Buyer when selecting the equipment. If hardware and/or equipment has been improperly or inadequately installed. If our equipment has been used to perform function other than the function it was designed to handle or exceeds its rated capacity. If our written instructions for installation and wiring or the electrical connections have not been followed. If our equipment is used with electrical accessories (switches, relays, etc.) that have not been previously approved in writing by Fabtex. If electrical accessories and other components have been used in disregard of the basic wiring diagram for which they were designed. All costs related to installation and reinstallation of the Fabtex equipment covered by this warranty are not the responsibility of Fabtex. Fabtex will not be responsible for any consequential damages during or following installation procedures. If the buyer resells any Fabtex products to another Buyer or End-user, it shall include all of the terms and provisions of this warranty in such resale. Fabtex s responsibility to any such Third Party shall be no greater than Fabtex s responsibility under the warranty to the original Buyer. No returns will be accepted without prior written authorization by Fabtex. All returns must be accompanied by a Return Authorization Number issued. To contact customer service, call toll free (800)

18 ROLLER SHADE SPECIFICATIONS MANUAL SHADES SECTION Part 1 General 1.1 Scope A. Furnish and install roller shades provided by Fabtex Inc., (800) B. Substitutions: Not Permitted C. Related work specified elsewhere 1.2 Quality Assurance A. Installer qualifications: 1. The installer shall be a firm approved by Fabtex, Inc. 2. The installer shall be qualified to install the product specified, as demonstrated by prior experience. B. Job mock-up: A sample shade may be installed on the jobsite prior to the beginning of the project. 1.3 Submittals A. Product information: Submit Fabtex product literature and installation instructions. B. Shop drawings: Indicate field-measured dimensions of opening which are to receive shades, details on mounting surface and sill conditions, and details of corners and conditions between adjacent shades. C. Color samples: Submit a sample of each type and color of material specified. 1.4 Delivery, Storage, and Handling A. Packing and shipping: 1. Materials shall be delivered to the Project in the Fabtex original unopened packaging with labels intact. B. Storage: 1. Materials shall be stored in a clean area, which is free of corrosive fumes, dust, and away from construction activities. 2. Materials shall be stacked horizontally using plastic or wood shims such that drainage and ventilation are provided for, and such that water cannot accumulate in, about or upon containers. 3. Stacks shall be covered with tarpaulins or plastic such that ventilation is provided for, and such that contaminants are prevented from contacting surfaces. 1.5 Project/Site Conditions (Before Product Installation Begins) A. Roof must be tight, windows and frames installed and glazed, and interior doors hung. B. Wet work including concrete, masonry, plaster, stucco, terrazzo, sheetrock, spackling, and taping (including sanding) shall be complete and dry. C. Ceilings, window pockets, electrical, and mechanical work above the product shall be complete. D. Electrical power (110 volt AC) shall be available for installer s tools within 500 ft. of product installation areas. E. Flooring materials such as carpet, tile, etc. must be completed. 1.6 Warranty A. Lifetime limited warranty: Fabtex, Inc. shall repair or replace for the ten year expected life of the roller shade, at its option, without charge, any part found defective in workmanship or material as long as the roller shade remains in the same window for which it was purchased. Part 2 Products 2.1 Manufacturer and Product Description A. Product: 1. Manual Roller Shades B. Acceptable manufacturer 1. Fabtex Inc., (800) in accordance with specifications, drawings, and contract documents.

19 ROLLER SHADE SPECIFICATIONS MANUAL SHADES SECTION Part 2 Products (continued) C. Substitutions: Not Permitted D. Materials 1. Fabric a. Selected from the Fabtex Roller Shade Collection. Available in a variety of solar screen, light filtering, and room darkening fabrics. b. Dual shade systems require two fabric selections. Typically one blackout and one solar screen. 2. Clutch Mechanism a. Shall be made in corrosion resistant plastic and internal mechanisms of Nylon 6 construction. Shall consist of a heavy duty single wrap spring that creates a positive mechanical relationship between the roller shade tube unit and the universal installation brackets to ensure stationary positioning in the static state. When activated the wrap spring releases and permits the clutch to turn while reducing friction on the clutch. The clutch will be press fit into the tube with ribs that engage with the tube s internal locking channels. The chain control will be available on either the right or the left side of the shade. i. Clutch End Locking System: The clutch shall have a locking system which prevents the shade from coming out of its brackets if the shade is operated incorrectly. b. Dual shade systems utilize two clutches. Chain controls can be positioned both right, both left, or one right and one left. 3. Idle End Cap a. Shall be made of nylon with a spring steel loaded center pin for smooth and quiet operation. The idle end spring shall be made of zinc plated spring steel and will be press fit into the tube with ribs that engage with the tube s internal locking channels. The idle end of clutch shall be spring loaded for ease of installation and security of fixing. 4. Lift Chain a. Stainless steel #10 bead chain is standard. b. Polyester cord with nylon bead is available. 5. Tube Mechanism a. All tubes shall be 100% extruded T6 aluminum with a diameter and a wall thickness required to support shade fabric without excessive deflection. Four tube extrusions shall be used depending upon the size of the shade and the weight of the fabric selected. Each tube shall have at least one internal raised rib to increase the rigidity of the tube and thus enabling shades to span wider openings without the risk of the tube sagging when the shade is operated. 6. Hembars a. Standard i. An aluminum extrusion 1 in height held inside a fabric bottom-pocket. The bottompocket shall be created by folding a 1 1/4 section of fabric behind the bottom of the shade and RF welding the fabric to itself. After the aluminum weight is inserted into the bottom-pocket, the edges will be sealed by again RF welding the fabric edges to itself. b. External optional i. An aluminum extrusion in clear anodized, white, alabaster, black, or dark bronze attached to the bottom edge of the fabric ii. Available with Edge Seal stripping along the bottom edge to aid in creating a tight light gap. Typically only used for blackout bands. 7. Installation Brackets a. Without Fascia

20 ROLLER SHADE SPECIFICATIONS MANUAL SHADES SECTION Part 2 Products (continued) i. Standard Brackets: Shall be universal. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white or black painted finish. ii. Dual Lite Brackets: required for dual shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white painted finish. b. Installation Brackets with Fascia i. Standard Box Brackets: Shall be universal. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white, bone, bronze or black painted finish. ii. Dual Lite Box Brackets: used for dual shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white, bone, bronze or black painted finish. iii. 5 Inch Fascia Brackets: Shall be universal. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a zinc, white, bronze or black painted finish. iv. 7 Inch Standard Box Brackets: used for dual shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white, bone, bronze or black painted finish. 8. Valance Options: a. Fascia i. 3 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with small to medium size standard shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bone, bronze, and black. Matching fabric wrapped and custom paint available. ii. 4 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with medium to large size standard shade systems and small to medium dual lite shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bone, bronze, and black. Matching fabric wrapped and custom paint available. iii. 3 Inch Round Fascia Valance: Shall be a contoured shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with small to medium size standard shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bone, bronze, and black. Matching fabric wrapped and custom paint available. iv. 4 Inch Round Fascia Valance: Shall be a contoured shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with medium to large size standard shade systems and small to medium dual lite shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bone, bronze, and black. Matching fabric wrapped and custom paint available. v. 5 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Can be inverted for reverse roll applications and used as back fascia for aesthetics and light leakage prevention. Designed for use with large to very-large size standard shade systems and medium to large size dual shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bronze, and black. Matching fabric wrapped and custom paint available.

21 ROLLER SHADE SPECIFICATIONS MANUAL SHADES SECTION Part 2 Products (continued) vi. 7 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with very-large size standard shade systems and large size dual shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bronze, and black. Matching fabric wrapped and custom paint available. b. Headbox i. Standard Shade Pocket (5.5 x 5 Headbox): Shall be a one-piece U shaped aluminum extrusion with optional removable bottom closure plate. The shade pocket will encase and conceal the roller shade tube mechanism. It is designed to be installed either in a ceiling pocket, to the ceiling, or to the wall. Aluminum end caps are available and may be fixed at both ends of the extrusion. Available as white. Custom colors available upon request. ii. Single Shade Pocket with Tile Clip (5.5 x 5 Headbox): Shall be a one-piece U shaped aluminum extrusion with front lip extension and optional removable bottom closure plate. The shade pocket will encase and conceal the roller shade tube mechanism. It is designed to be installed flush with a T-Bar type ceiling. Aluminum end caps are available and may be fixed at both ends of the extrusion. Available as white. Custom colors available upon request. iii. Dual Shade Pocket (7 x 9 Headbox): Shall be a one-piece U shaped aluminum extrusion with optional removable bottom closure plate. Designed for use with very large single roller shades and dual shade systems. The shade pocket will encase and conceal the roller shade tube mechanism. It is designed to be installed either in a ceiling pocket, to the ceiling, or to the wall. Aluminum end caps are available and may be fixed at both ends of the extrusion. Available as white. Custom colors available upon request. 9. Side & Sill Channels: a. Shall be a one-piece U shaped aluminum extrusion that may be installed at each side and/or to the window sill to eliminate left, right, and bottom edge light gaps. b. Note! Side and Sill Channels are typically only used on the blackout band. 10. Shade Guardian a. Shall provide in a single piece a dual mechanism for controlling the stopping speed and position of a chain mounted ball stop. b. By the action of this mechanism the shade shall be protected from user abuse where by the ball stop would impact and damage the manual clutch mechanism. 2.2 Fabrication A. Prior to fabrication, verify actual opening dimensions by on-site measurement. Calculate roller shade dimensions to fit within specified tolerances. B. Fabricate roller shades to fill openings from head to sill and jamb to jamb. The minimum clearance shade-to-shade shall be 1/4. Locate shade divisions at mullions. Part 3 Execution 3.1 Inspection A. Verify that the work area in which the roller shades will be installed is free of conditions that interfere with roller shade installations and operations. Begin shade installation only when unsatisfactory conditions have been corrected. 1. General: The shade shall be free of sharp edges, burrs or other defects which might be harmful. When other materials result in improved specifications, they may be adopted.

22 ROLLER SHADE SPECIFICATIONS MANUAL SHADES SECTION Part 3 Execution (continued) 2. Size Limitations: a. Maximum width: To be determined depending upon the size of the shade tube. Multiple band shade panels connected with intermediate brackets are also available. b. Maximum drop: To be determined depending upon the size of the shade tube. 3.2 Installation A. Install shades in accordance with Fabtex, Inc. procedures except as otherwise specified herein. B. Install shades with adequate clearance to permit smooth operation of shades and any sash operators. Hold roller shades 1/4 clear from each side of window opening on inside mount unless other clearance is indicated. 3.3 Cleaning A. Clean soiled shades surfaces with a mild soap solution. Do not use steam, hot water, bleach or any abrasive or solvent-based cleaners. Do not machine wash. To ensure proper drying, provide adequate ventilation for shades.

23 ROLLER SHADE SPECIFICATIONS MOTORIZED SHADES SECTION Part 1 General 1.1 Scope A. Furnish and install roller shades provided by Fabtex Inc., (800) B. Substitutions: Not Permitted C. Related work specified elsewhere 1.2 Quality Assurance A. Installer qualifications: 1. The installer shall be a firm approved by Fabtex, Inc. 2. The installer shall be qualified to install the product specified, as demonstrated by prior experience. B. Job mock-up: A sample shade may be installed on the jobsite prior to the beginning of the project. 1.3 Submittals A. Product information: Submit Fabtex product literature and installation instructions. B. Shop drawings 1. Indicate field-measured dimensions of opening which are to receive shades, details on mounting surface and sill conditions, and details of corners and conditions between adjacent shades. 2. Provide system wiring diagrams. C. Color samples: Submit a sample of each type and color of material specified. 1.4 Delivery, Storage, and Handling A. Packing and shipping: 1. Materials shall be delivered to the Project in the Fabtex original unopened packaging with labels intact. B. Storage: 1. Materials shall be stored in a clean area, which is free of corrosive fumes, dust, and away from construction activities. 2. Materials shall be stacked horizontally using plastic or wood shims such that drainage and ventilation are provided for, and such that water cannot accumulate in, about or upon containers. 3. Stacks shall be covered with tarpaulins or plastic such that ventilation is provided for, and such that contaminants are prevented from contacting surfaces. 1.5 Project/Site Conditions (Before Product Installation Begins) A. Roof must be tight, windows and frames installed and glazed, and interior doors hung. B. Wet work including concrete, masonry, plaster, stucco, terrazzo, sheetrock, spackling, and taping (including sanding) shall be complete and dry. C. Ceilings, window pockets, electrical, and mechanical work above the product shall be complete. D. Electrical power (110 volt AC) shall be available for installer s tools within 500 ft. of product installation areas. E. Flooring materials such as carpet, tile, etc. must be completed. 1.6 Warranty A. Lifetime limited warranty: Fabtex, Inc. shall repair or replace for the ten year expected life of the roller shade, at its option, without charge, any part found defective in workmanship or material as long as the roller shade remains in the same window for which it was purchased. Part 2 Products 2.1 Manufacturer and Product Description A. Acceptable product: Fabtex motorized roller shades manufactured by Fabtex, Inc. B. Motor Selection 1. PS45 Standard Drive Unit

24 ROLLER SHADE SPECIFICATIONS MOTORIZED SHADES SECTION Part 2 Products (continued) a. Tubular, asynchronous operator, built in reversible capacitor, brushless 110V AC (60 Hz) single phase motor, thermally protected, permanently lubricated gearbox, maintenance free. b. Built in, digital control system, delivers automatic alignment with a +/ 2mm accuracy, programmable configuration via motor mounted push buttons. Systems using a time function for positioning are not acceptable. c. Upper and lower limits are preset by shade manufacturer and adjustable on site. d. 100 degrees of resolution: motor can be positioned at full-up, full-down or any position between 0-100% in 1 percent increments. e. Each drive unit has a whisper quiet sound output (this can vary based on installation environment and shade manufacturer hardware). f. Wiring i. Motors can be parallel wired together to a single circuit. Total load not to exceed circuit or switch capacity. Consult a certified electrical contractor for recommended power layout. g. Programming i. Motors can be individually programmed at any time; in single or parallel wired configurations h. Power cord (5 conductor - high voltage) i. 6 feet (2m) standard 2. Plugin RTM Radio Controlled Drive Unit a. Tubular, asynchronous operator, built in reversible capacitor, brushless 110V AC (60 Hz) single phase motor, thermally protected, permanently lubricated gearbox, maintenance free. b. Built in, digital control system, delivers automatic alignment with a +/ 2mm accuracy, programmable configuration via wireless remote. Systems using a time function for positioning are not acceptable. c. Upper and lower limits are preset by shade manufacturer and adjustable on site via hand held device. d. 100 degrees of resolution: motor can be positioned at full-up, full-down or any position between 0-100% in 1 percent increments. e. Controlling device stores the unique ID code of the motor(s) to which it is programmed. f. Each drive unit has a whisper quiet sound output (this can vary based on installation environment, mounting conditions, and selected hardware). g. Power cord (high voltage) with built in C13/C14 quick disconnect i. 1.5 feet (0.5m) ii. 3 feet (1m) iii. 6 feet (2m) standard iv. 13 feet (4m) standard v. 19 feet (6m) vi. 26 feet (8m) 3. Battery RTM Radio Controlled Drive Unit a. Tubular, asynchronous operator, internal lithium-ion battery, thermally protected, permanently lubricated gearbox, maintenance free. b. Battery is to be continuously trickle charged via i. Solar panel ii. Wall charger c. Built in, digital control system, delivers automatic alignment with a +/ 2mm accuracy, programmable configuration via wireless remote. Systems using a time function for positioning are not acceptable.

25 ROLLER SHADE SPECIFICATIONS MOTORIZED SHADES SECTION Part 2 Products (continued) d. Upper and lower limits are preset by shade manufacturer and adjustable on site via hand held device. e. 100 degrees of resolution: motor can be positioned at full-up, full-down or any position between 0-100% in 1 percent increments. f. Each drive unit has a quiet sound output (this can vary based on installation environment, mounting conditions, and selected hardware). 4. ILT Intelligent Drive Unit a. Tubular, asynchronous operator, built in reversible capacitor, brushless 110V AC (60 Hz) single phase motor, thermally protected, permanently lubricated gearbox, maintenance free. b. Built in, digital control system, delivers automatic alignment with a +/ 2mm accuracy, programmable configuration via PC. Systems using a time function for positioning are not acceptable. c. Upper and lower limits are preset by shade manufacturer and adjustable on site via hand held device, no need to access the roller assembly. No external, mechanical limit wheels or buttons are involved. d. Up to sixteen intermediate stopping points are electronically precision set and locked into non-volatile memory. e. 100 degrees of resolution: motor can be positioned at full-up, full-down or any position between 0-100% in 1 percent increments. f. Motor can be a member of up to 16 groups; the system can have an unlimited number of groups. g. Each unit is capable of automatically aligning itself to a referenced shade position upon receiving a command from the SVI control software. h. Each drive unit has a whisper quiet sound output (this can vary based on installation environment, mounting conditions, and selected hardware). i. Power cord (high voltage) i. 6 (2m) standard ii. 12 (4m) optional iii. 18 (6m) optional iv. 24 (8m) optional j. Control Cord (low voltage) i. 6 (2m) of four conductor flat control cable with an RJ-9 modular connector. k. Testing i. Motors are UL recognized and meet CSA standards. ii. All internal electrical components are tested to withstand a 15kV electrostatic discharge without damage or loss of memory. C. Materials: 1. Fabric a. Selected from the Fabtex Roller Shade Collection. Available in a variety of solar screen, light filtering, and room darkening fabrics. b. Dual shade systems require two fabric selections. Typically one blackout and one solar screen. 2. Tube Mechanism a. All tubes shall be 100% extruded T6 aluminum with a diameter and a wall thickness required to support shade fabric without excessive deflection. Four tube extrusions shall be used depending upon the size of the shade and the weight of the fabric selected. Each tube shall have at least one internal raised rib to increase the rigidity of the tube and thus enabling shades to span wider openings without the risk of the tube sagging when the shade is operated.

26 ROLLER SHADE SPECIFICATIONS MOTORIZED SHADES SECTION Part 2 Products (continued) 3. Hembars: a. Standard i. An aluminum extrusion 1 in height held inside a fabric bottom-pocket. The bottompocket shall be created by folding a 1 1/4 section of fabric behind the bottom of the shade and RF welding the fabric to itself. After the aluminum weight is inserted into the bottom-pocket, the edges will be sealed by again RF welding the fabric edges to itself. b. External optional i. An aluminum extrusion in clear anodized, white, alabaster, black, or dark bronze attached to the bottom edge of the fabric ii. Available with Edge Seal stripping along the bottom edge to aid in creating a tight light gap. Typically only used for blackout bands. 4. Installation Brackets a. Without Fascia i. Standard Brackets: Shall be universal. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a zinc or white painted finish. ii. Dual Lite Brackets: required for dual shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white painted finish. b. Installation Brackets with Fascia i. Standard Box Brackets: Shall be universal. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white, bone, bronze or black painted finish. ii. Dual Lite Box Brackets: required for dual shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white, bone, bronze or black painted finish. iii. 5 Inch Box Brackets: required for 5 Inch Fascia shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a zinc, white, bronze, or black painted finish. iv. Dual Standard Box Brackets: required for dual shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white, bone, bronze or black painted finish. 5. Valance Options a. Fascia i. 4 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with medium to large size standard shade systems and small to medium dual lite shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bone, bronze, and black. Matching fabric wrapped and custom paint available. ii. 4 Inch Round Fascia Valance: Shall be a contoured shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with medium to large size standard shade systems and small to medium dual lite shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bone, bronze, and black. Matching fabric wrapped and custom paint available.

27 ROLLER SHADE SPECIFICATIONS MOTORIZED SHADES SECTION Part 2 Products (continued) iii. 5 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Can be inverted for reverse roll applications and used as back fascia for aesthetics and light leakage prevention. Designed for use with large to very-large size standard shade systems and medium to large size dual shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bronze, and black. Matching fabric wrapped and custom paint available. iv. 7 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with very-large size standard shade systems and large size dual shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bronze, and black. Matching fabric wrapped and custom paint available. b. Headbox i. Standard Shade Pocket (5.5 x 5 Headbox): Shall be a one-piece U shaped aluminum extrusion with optional removable bottom closure plate. The shade pocket will encase and conceal the roller shade tube mechanism. It is designed to be installed either in a ceiling pocket, to the ceiling, or to the wall. Aluminum end caps are available and may be fixed at both ends of the extrusion. Available as white. Custom colors available upon request. ii. Single Shade Pocket with Tile Clip (5.5 x 5 Headbox): Shall be a one-piece U shaped aluminum extrusion with front lip extension and optional removable bottom closure plate. The shade pocket will encase and conceal the roller shade tube mechanism. It is designed to be installed flush with a T-Bar type ceiling. Aluminum end caps are available and may be fixed at both ends of the extrusion. Available as white. Custom colors available upon request. iii. Dual Shade Pocket (7 x 9 Headbox): Shall be a one-piece U shaped aluminum extrusion with optional removable bottom closure plate. Designed for use with very large single roller shades and dual shade systems. The shade pocket will encase and conceal the roller shade tube mechanism. It is designed to be installed either in a ceiling pocket, to the ceiling, or to the wall. Aluminum end caps are available and may be fixed at both ends of the extrusion. Available as white. Custom colors available upon request. 6. Side & Sill Channels a. Shall be a one-piece U shaped aluminum extrusion that may be installed at each side and/or to the window sill to eliminate left, right, and bottom edge light gaps. b. Note! Side and Sill Channels are typically only used on the blackout band. 2.2 Controls A. Non-Intelligent 1. Standard Motors a. Utilizing standard switches, run shades individually or in groups. 2. RTM Motors a. Utilizing battery powered switches and remotes, run shades individually, in groups, or configure into zones. Each wireless device to have a range of 50 ft. without obstructions. 3. ILT Motors a. Utilizing low voltage switches, run shades individually, in groups, or configure into zones. Each switch directly controls the motor, group, or zone to which it is physically connected. B. Intelligent 1. ILT Motors