ROTOR RESISTANCE SPEED CONTROL OF WOUND ROTOR INDUCTION MOTOR

Size: px
Start display at page:

Download "ROTOR RESISTANCE SPEED CONTROL OF WOUND ROTOR INDUCTION MOTOR"

Transcription

1 1 Electrical Machines Lab Experiment-No. ROTOR RESISTANCE SPEED CONTROL OF WOUND ROTOR INDUCTION MOTOR AIM: To vary the speed of the wound rotor induction motor using rotor rheostat control. Theory The main advantage of wound rotor induction motor over the squirrel cage motor is that it offers one more degree of freedom to the Engineers for starting & speed control. Wound rotor Induction Motor is used where the load requirements are high starting toque & variable speed, or where the motor is to be started under heavy load. Typical applications of these motors are crane & hoist control. Resister controllers in the rotor circuit are used to achieve smooth start & speed control. Resent investigations have shown that certain desired torque speed characteristics can be achieved by insertion of relatively simple passive frequency sensitive networks. Careful selection of network parameters leads to highly reduced starting current & & improved torque/ current ratio. To understand the industrial systems incorporating the wound rotor Induction Motors it is therefore necessary to study the effect of rotor impedance on the performance of Induction Motors. In this method of speed control of three phase induction motor external resistance are added on rotor side. The equation of torque for three phase induction motor is The three phase induction motor operates in low slip region. In low slip region term (sx)2 becomes very small as compared to R2. So, it can be neglected. And also E2 is constant. So the equation of torque after simplification becomes,

2 2 Now if we increase rotor resistance, R2 torque decreases but to supply the same load torque must remain constant. So, we increase slip, which will further results in decrease in rotor speed. Thus by adding additional resistance in rotor circuit we can decrease the speed of three phase induction motor. The main advantage of this method is that with addition of external resistance starting torque increases but this method of speed control of three phase induction motor also suffers from some disadvantages: 1. The speed above the normal value is not possible. 2. Large speed change requires large value of resistance and if such large value of resistance is added in the circuit it will cause large copper loss and hence reduction in efficiency. 3. Presence of resistance causes more losses. 4. This method cannot be used for squirrel cage induction motor. From the figure 1 it is clear how does the speed vary with the change of rotor resistance.

3 3 The model used to simulate this experiment Figure 2 simulation the wound rotor induction motor Parameters of components 1- A synchronous machine block: a- Configuration: Preset model: No Mechanical input: Torque Tm Rotor type: wound rotor Reference frame: Rotor Mass units: SI b- Parameters:

4 4 Pn (VA): 2850 Vn (Vrms L-L): 380 f(hz): 50 Another data are remain constant c- Advanced: Sample time: -1 3 phase source: This block consists of three A.C. Voltage sources, as shown below: 1- Phase A: 2- V= K/ (sqrt (3)*sqrt(2)) 3- f= 50Hz 4- Phase= 0 degree 5- Sample time= Phase B: 7- V= K/ (sqrt (3)*sqrt(2)) 8- f= 50Hz 9- Phase= -120 degree 10- Sample time= Phase C: 12- V= K/ (sqrt (3)*sqrt(2)) 13- f= 50Hz 14- Phase= -240 degree 15- Sample time= -1

5 5 PROCEDURE: 1 - Open File ---> New---> Model. 2 - Open Simulink Library and browse the components. 3 - Connect the components as shown in the above circuit, figure Simulate the circuit to start motor with rotor resistance starter. 5 observe the waveforms of speed, torque, stator current and rotor current. 6 - The rotor resistance is varied and corresponding values of speed, voltage, currents and torque are noted down. Rotor Resistance Voltage (V) Stator current (A) Rotor current(a) Speed (rpm) Torque (N.m) Report 1- Plot the relation between the rotor resistances with speed. 2- As you added resistance externally to the rotor circuit, what happened to rotor speed? Why? 3- As rotor speed decreased, what happened to the torque output of the motor? Why? 4- As rotor speed decreased, what happened to the current being induced into the rotor circuit?

Lecture 20: Stator Control - Stator Voltage and Frequency Control

Lecture 20: Stator Control - Stator Voltage and Frequency Control Lecture 20: Stator Control - Stator Voltage and Frequency Control Speed Control from Stator Side 1. V / f control or frequency control - Whenever three phase supply is given to three phase induction motor

More information

DEPARTMENT OF EI ELECTRICAL MACHINE ASSIGNMENT 1

DEPARTMENT OF EI ELECTRICAL MACHINE ASSIGNMENT 1 It is the mark of an educated mind to be able to entertain a thought without accepting it. DEPARTMENT OF EI ELECTRICAL MACHINE ASSIGNMENT 1 1. Explain the Basic concepts of rotating machine. 2. With help

More information

VALLIAMMAI ENGINEERING COLLEGE MECHANICAL ENGINEERING ANNA UNIVERSITY CHENNAI II YEAR MECH / III SEMESTER EE6351 - ELECTRICAL DRIVES AND CONTROL (REGULATION 2013) UNIT I INTRODUCTION PART-A (2 MARKS) 1.

More information

The Wound-Rotor Induction Motor Part I

The Wound-Rotor Induction Motor Part I Experiment 1 The Wound-Rotor Induction Motor Part I OBJECTIVE To examine the construction of the three-phase wound-rotor induction motor. To understand exciting current, synchronous speed and slip in a

More information

Three-Phase Induction Motor With Frequency Inverter

Three-Phase Induction Motor With Frequency Inverter Objectives Experiment 9 Three-Phase Induction Motor With Frequency Inverter To be familiar with the 3-phase induction motor different configuration. To control the speed of the motor using a frequency

More information

Regulation: R16 Course & Branch: B.Tech EEE

Regulation: R16 Course & Branch: B.Tech EEE SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (Descriptive) Subject with Code : Electrical Machines-II (16EE215) Regulation: R16 Course & Branch: B.Tech

More information

R13 SET - 1. b) Describe different braking methods employed for electrical motors. [8M]

R13 SET - 1. b) Describe different braking methods employed for electrical motors. [8M] Code No:RT32026 R13 SET - 1 III B. Tech II Semester Regular Examinations, April - 2016 POWER SEMICONDUCTOR DRIVES (Electrical and Electronics Engineering) Time: 3 hours Maximum Marks: 70 Note: 1. Question

More information

FATIMA MICHAEL COLLEGE OF ENGINEERING & TECHNOLOGY Senkottai Village, Madurai Sivagangai Main Road, Madurai

FATIMA MICHAEL COLLEGE OF ENGINEERING & TECHNOLOGY Senkottai Village, Madurai Sivagangai Main Road, Madurai Department of Mechanical Engineering QUESTION BANK SUBJECT NAME: ELECTRICAL DRIVES AND CONTROL YEAR / SEM: II / III UNIT I INTRODUCTION PART-A (2 MARKS) 1. Define Drives 2. Define Electric Drives. 3. What

More information

Starting of Induction Motors

Starting of Induction Motors 1- Star Delta Starter The method achieved low starting current by first connecting the stator winding in star configuration, and then after the motor reaches a certain speed, throw switch changes the winding

More information

ESO 210 Introduction to Electrical Engineering

ESO 210 Introduction to Electrical Engineering ESO 210 Introduction to Electrical Engineering Lectures-37 Polyphase (3-phase) Induction Motor 2 Determination of Induction Machine Parameters Three tests are needed to determine the parameters in an induction

More information

CHAPTER 6 DESIGN AND DEVELOPMENT OF DOUBLE WINDING INDUCTION GENERATOR

CHAPTER 6 DESIGN AND DEVELOPMENT OF DOUBLE WINDING INDUCTION GENERATOR 100 CHAPTER 6 DESIGN AND DEVELOPMENT OF DOUBLE WINDING INDUCTION GENERATOR 6.1 INTRODUCTION Conventional energy resources are not sufficient to meet the increasing electrical power demand. The usages of

More information

694 Electric Machines

694 Electric Machines 694 Electric Machines 9.1 A 4-pole wound-rotor induction motor is used as a frequency changer. The stator is connected to a 50 Hz, 3-phase supply. The load is connected to the rotor slip rings. What are

More information

AC MOTOR TYPES. DESCRIBE how torque is produced in a single-phase AC motor. EXPLAIN why an AC synchronous motor does not have starting torque.

AC MOTOR TYPES. DESCRIBE how torque is produced in a single-phase AC motor. EXPLAIN why an AC synchronous motor does not have starting torque. Various types of AC motors are used for specific applications. By matching the type of motor to the appropriate application, increased equipment performance can be obtained. EO 1.5 EO 1.6 EO 1.7 EO 1.8

More information

Unit III-Three Phase Induction Motor:

Unit III-Three Phase Induction Motor: INTRODUCTION Unit III-Three Phase Induction Motor: The three phase induction motor runs on three phase AC supply. It is an ac motor. The power is transferred by means of induction. So it is also called

More information

Pretest Module 21 Units 1-3 AC Generators & Three-Phase Motors

Pretest Module 21 Units 1-3 AC Generators & Three-Phase Motors Pretest Module 21 Units 1-3 AC Generators & Three-Phase Motors 1. What are the two main parts of a three-phase 2. Which part of a three-phase squirrel-cage induction motor is a hollow core? 3. What are

More information

DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING

DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK 16EET41 SYNCHRONOUS AND INDUCTION MACHINES UNIT I SYNCHRONOUS GENERATOR 1. Why the stator core is laminated? 2. Define voltage regulation

More information

2014 ELECTRICAL TECHNOLOGY

2014 ELECTRICAL TECHNOLOGY SET - 1 II B. Tech I Semester Regular Examinations, March 2014 ELECTRICAL TECHNOLOGY (Com. to ECE, EIE, BME) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~~~~~

More information

VIII. Three-phase Induction Machines (Asynchronous Machines) Induction Machines

VIII. Three-phase Induction Machines (Asynchronous Machines) Induction Machines VIII. Three-phase Induction Machines (Asynchronous Machines) Induction Machines 1 Introduction Three-phase induction motors are the most common and frequently encountered machines in industry simple design,

More information

(d) None of the above.

(d) None of the above. Dr. Mahalingam College of Engineering and Technology, Pollachi-3 (An Autonomous Institution affiliated to Anna niversity) CCET II (2016 Regulation) Name of Programme: B.E. (EEE) Course Code & Course Title:

More information

Pretest Module 21 Units 1-4 AC Generators & Three-Phase Motors

Pretest Module 21 Units 1-4 AC Generators & Three-Phase Motors Pretest Module 21 Units 1-4 AC Generators & Three-Phase Motors 1. What are the two main parts of a three-phase motor? Stator and Rotor 2. Which part of a three-phase squirrel-cage induction motor is a

More information

Stator rheostat, Autotransformer Star to Delta starter and rotor resistance starter.

Stator rheostat, Autotransformer Star to Delta starter and rotor resistance starter. UNIT-IV 1.What are the types of starters? Stator rheostat, Autotransformer Star to Delta starter and rotor resistance starter. 2. List out the methods of speed control of cage type 3-phase induction motor?

More information

INSTITUTE OF AERONAUTICAL ENGINEERING Dundigal, Hyderabad

INSTITUTE OF AERONAUTICAL ENGINEERING Dundigal, Hyderabad INSTITUTE OF AERONAUTICAL ENGINEERING Dundigal, Hyderabad - 500 043 MECHANICAL ENGINEERING ASSIGNMENT Name : Electrical and Electronics Engineering Code : A40203 Class : II B. Tech I Semester Branch :

More information

EEE3441 Electrical Machines Department of Electrical Engineering. Lecture. Introduction to Electrical Machines

EEE3441 Electrical Machines Department of Electrical Engineering. Lecture. Introduction to Electrical Machines Department of Electrical Engineering Lecture Introduction to Electrical Machines 1 In this Lecture Induction motors and synchronous machines are introduced Production of rotating magnetic field Three-phase

More information

SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR

SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (DESCRIPTIVE) Subject with Code : ET(16EE212) Year & Sem: II-B.Tech & II-Sem UNIT I DC GENERATORS Course

More information

Iowa State University Electrical and Computer Engineering. E E 452. Electric Machines and Power Electronic Drives

Iowa State University Electrical and Computer Engineering. E E 452. Electric Machines and Power Electronic Drives Electrical and Computer Engineering E E 452. Electric Machines and Power Electronic Drives Laboratory #12 Induction Machine Parameter Identification Summary The squirrel-cage induction machine equivalent

More information

2. Draw the speed-torque characteristics of dc shunt motor and series motor. (May2013) (May 2014)

2. Draw the speed-torque characteristics of dc shunt motor and series motor. (May2013) (May 2014) UNIT 2 - DRIVE MOTOR CHARACTERISTICS PART A 1. What is meant by mechanical characteristics? A curve is drawn between speed-torque. This characteristic is called mechanical characteristics. 2. Draw the

More information

DHANALAKSHMI COLLEGE OF ENGINEERING MANIMANGALAM. TAMBARAM, CHENNAI B.E. ELECTRICAL AND ELECTRONICS ENGINEERING

DHANALAKSHMI COLLEGE OF ENGINEERING MANIMANGALAM. TAMBARAM, CHENNAI B.E. ELECTRICAL AND ELECTRONICS ENGINEERING DHANALAKSHMI COLLEGE OF ENGINEERING MANIMANGALAM. TAMBARAM, CHENNAI B.E. ELECTRICAL AND ELECTRONICS ENGINEERING V SEMESTER EE2305 ELECTRICAL MACHINES II LABORATORY LABORATORY MANUAL 1 CONTENT S. No. Name

More information

Performance Analysis of 3-Ø Self-Excited Induction Generator with Rectifier Load

Performance Analysis of 3-Ø Self-Excited Induction Generator with Rectifier Load Performance Analysis of 3-Ø Self-Excited Induction Generator with Rectifier Load,,, ABSTRACT- In this paper the steady-state analysis of self excited induction generator is presented and a method to calculate

More information

Dev Bhoomi Institute Of Technology LABORATORY Department of Electrical And Electronics Engg. Electro-mechanical Energy Conversion II

Dev Bhoomi Institute Of Technology LABORATORY Department of Electrical And Electronics Engg. Electro-mechanical Energy Conversion II REV. NO. : REV. DATE : PAGE: 1 Electro-mechanical Energy Conversion II 1. To perform no load and blocked rotor tests on a three phase squirrel cage induction motor and determine equivalent circuit. 2.

More information

SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road QUESTION BANK (DESCRIPTIVE)

SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road QUESTION BANK (DESCRIPTIVE) SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (DESCRIPTIVE) Subject with Code : PSD (16EE223) Year & Sem: III-B.Tech & II-Sem Course & Branch: B.Tech

More information

GROUP OF INSTITUTIONS :: PUTTUR UNIT I SINGLE PHASE TRANSFORMERS

GROUP OF INSTITUTIONS :: PUTTUR UNIT I SINGLE PHASE TRANSFORMERS SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (Descriptive) Subject with Code : Electrical Machines-II (16EE215) Course & Branch: B.Tech EEE Regulation:

More information

Chapter 3.2: Electric Motors

Chapter 3.2: Electric Motors Part I: Objective type questions and answers Chapter 3.2: Electric Motors 1. The synchronous speed of a motor with 6 poles and operating at 50 Hz frequency is. a) 1500 b) 1000 c) 3000 d) 750 2. The efficiency

More information

ELECTRICAL MAINTENANCE

ELECTRICAL MAINTENANCE ELECTRICAL MAINTENANCE II PRACTICAL JOURNAL DATA 1 EXPERIMENT NO. 1 AIM: TO FIND VOLTAGE RATIO OF A GIVEN TRANSFORMER. CIRCUIT DIAGRAM: OBSERVATION TABLE: Sr.No. 1 2 3 4 Primary Voltage (V 1 ) Secondary

More information

Circuit Diagram For Speed Control Of Slip Ring Induction Motor

Circuit Diagram For Speed Control Of Slip Ring Induction Motor Circuit Diagram For Speed Control Of Slip Ring Induction Motor A wound-rotor motor is a type of induction motor where the rotor windings are Compared to a squirrel-cage rotor, the rotor of the slip ring

More information

2-marks question bank UNIT I - TRANSFORMERS UNIT II: AC MACHINES

2-marks question bank UNIT I - TRANSFORMERS UNIT II: AC MACHINES 2-marks question bank UNIT I - TRANSFORMERS 1. What is all day efficiency? 2. What are the applications of auto transformers? 3. Why transformer rating is expressed in KVA? 4. Does transformer draw any

More information

CHAPTER 7 INDUCTION MOTOR

CHAPTER 7 INDUCTION MOTOR CHAPTE 7 INDUCTION MOTO Summary: 1. Induction Motor Construction. Basic Induction Motor Concepts - The Development of Induced Torque in an Induction Motor. - The Concept of otor Slip. - The Electrical

More information

Department of Electrical and Computer Engineering

Department of Electrical and Computer Engineering Page 1 of 1 Faculty of Engineering, Architecture and Science Department of Electrical and Computer Engineering Course Number EES 612 Course Title Electrical Machines and Actuators Semester/Year Instructor

More information

Fachpraktikum Elektrische Maschinen. Theory of Induction Machines

Fachpraktikum Elektrische Maschinen. Theory of Induction Machines Fachpraktikum Elektrische Maschinen Theory of Induction Machines Prepared by Arda Tüysüz January 2013 Fundamentals Induction machines (also known as asynchronous machines) are by far the most common type

More information

ELECTRIC MACHINES OPENLAB 0.2 kw

ELECTRIC MACHINES OPENLAB 0.2 kw THIS SYSTEM IS A COMPLETE SET OF COMPONENTS AND MODULES SUITABLE FOR ASSEMBLING THE ROTATING ELECTRIC MACHINES, BOTH FOR DIRECT CURRENT AND FOR ALTERNATING CURRENT. STUDENTS CAN PERFORM A CRITICAL AND

More information

Electrical Machines -II

Electrical Machines -II Objective Type Questions: 1. Basically induction machine was invented by (a) Thomas Alva Edison (b) Fleming (c) Nikola Tesla (d) Michel Faraday Electrical Machines -II 2. What will be the amplitude and

More information

SHRI ANGALAMMAN COLLEGE OF ENGINEERING AND TECHNOLOGY (An ISO 9001:2008 Certified Institution) SIRUGANOOR, TIRUCHIRAPPALLI

SHRI ANGALAMMAN COLLEGE OF ENGINEERING AND TECHNOLOGY (An ISO 9001:2008 Certified Institution) SIRUGANOOR, TIRUCHIRAPPALLI SHRI ANGALAMMAN COLLEGE OF ENGINEERING AND TECHNOLOGY (An ISO 9001:2008 Certified Institution) SIRUGANOOR, TIRUCHIRAPPALLI 621 105 DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING EE1205 - ELECTRICAL

More information

St.MARTIN S ENGINEERING COLLEGE Dhulapally, Secunderabad

St.MARTIN S ENGINEERING COLLEGE Dhulapally, Secunderabad St.MARTIN S ENGINEERING COLLEGE Dhulapally, Secunderabad-500 014 Subject: STATIC DRIVES Class : EEE III TUTORIAL QUESTION BANK Group I QUESTION BANK ON SHORT ANSWER QUESTION UNIT-I 1 What is meant by electrical

More information

Date: Name: ID: LABORATORY EXPERIMENT NO. 8 INDUCTION MOTOR/GENERATOR 8-1

Date: Name: ID: LABORATORY EXPERIMENT NO. 8 INDUCTION MOTOR/GENERATOR 8-1 Date: Name: ID: LABORATORY EXPERIMENT NO. 8 INDUCTION MOTOR/GENERATOR 8-1 OBJECT 1. To determine the general performance of a squirrel motors 2. To observe the characteristics of induction generators.

More information

General Purpose Permanent Magnet Motor Drive without Speed and Position Sensor

General Purpose Permanent Magnet Motor Drive without Speed and Position Sensor General Purpose Permanent Magnet Motor Drive without Speed and Position Sensor Jun Kang, PhD Yaskawa Electric America, Inc. 1. Power consumption by electric motors Fig.1 Yaskawa V1000 Drive and a PM motor

More information

PAC TRAINING PUMP MOTORS

PAC TRAINING PUMP MOTORS PAC TRAINING PUMP MOTORS 1 Basics Magnet supported from above N S N S Since unlike poles repel each other, the magnet will rotate Stationary Magnet 2 Basics N S Stationary Magnet 3 Basics N N S S Stationary

More information

Scheme - I. Sample Question Paper

Scheme - I. Sample Question Paper Program Name Program Code Course Title Sample Question Paper : Diploma in Industrial Electronics : IE : Electrical Machines and Transformers Max. Marks : 70 Time : 3 Hrs. Q1. ATTEMPT ANY FIVE OF THE FOLLOWING.

More information

ECE 325 Electric Energy System Components 6 Three Phase Induction Motors. Instructor: Kai Sun Fall 2016

ECE 325 Electric Energy System Components 6 Three Phase Induction Motors. Instructor: Kai Sun Fall 2016 ECE 325 Electric Energy System Components 6 Three Phase Induction Motors Instructor: Kai Sun Fall 2016 1 Content (Materials are from Chapters 13-15) Components and basic principles Selection and application

More information

EE6351 ELECTRIC DRIVES AND CONTROL UNIT-1 INTRODUTION

EE6351 ELECTRIC DRIVES AND CONTROL UNIT-1 INTRODUTION EE6351 ELECTRIC DRIVES AND CONTROL UNIT-1 INTRODUTION 1. What is meant by drive and electric drive? Machines employed for motion control are called drives and may employ any one of the prime movers for

More information

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING Course Name Course Code Class Branch INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad - 500 0 DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING : Static Drives : A60225 : III -

More information

Unit-II Synchronous Motor

Unit-II Synchronous Motor Unit-II Synchronous Motor CONSTRUCTION OF THREE PHASE SYNCHRONOUS MOTOR PRINCIPLE OF OPERATION Prepared By P.Priyadharshini Ap/EEE - 1 - Note: 1. The average torque exerted on the rotor of synchronous

More information

Load Test On 3 Phase Slip Ring Induction Motor Lab Manual

Load Test On 3 Phase Slip Ring Induction Motor Lab Manual Load Test On 3 Phase Slip Ring Induction Motor Lab Manual Electrical engineering machine lab manual. Brake test on three phase squirrel cage induction motor. No-load &, blocked rotor tests on three phase

More information

R07 SET - 1

R07 SET - 1 R07 SET - 1 II B. Tech II Semester Supplementary Examinations April/May 2013 ELECTRICAL MACHINES - II (Electrical and Electronics Engineering) Time: 3 hours Max. Marks: 80 Answer any FIVE Questions All

More information

AUCOM WHITE PAPER SERIES GET YOUR MOTOR RUNNING. An introduction to reduced voltage starting of three phase induction motors

AUCOM WHITE PAPER SERIES GET YOUR MOTOR RUNNING. An introduction to reduced voltage starting of three phase induction motors AUCOM WHITE PAPER SERIES GET YOUR MOTOR RUNNING An introduction to reduced voltage starting of three phase induction motors GET YOUR MOTOR RUNNING WHITE PAPER #1 Reduced voltage starting of three phase

More information

Motor Protection Fundamentals. Motor Protection - Agenda

Motor Protection Fundamentals. Motor Protection - Agenda Motor Protection Fundamentals IEEE SF Power and Energy Society May 29, 2015 Ali Kazemi, PE Regional Technical Manager Schweitzer Engineering Laboratories Irvine, CA Copyright SEL 2015 Motor Protection

More information

ST. ANNE S COLLEGE OF ENGINEERING AND TECHNOLOGY 9001:2015 CERTIFIED INSTITUTION) ANGUCHETTYPALAYAM, PANRUTI

ST. ANNE S COLLEGE OF ENGINEERING AND TECHNOLOGY 9001:2015 CERTIFIED INSTITUTION) ANGUCHETTYPALAYAM, PANRUTI ST. ANNE S COLLEGE OF ENGINEERING AND TECHNOLOGY (AN ISO 9001:2015 CERTIFIED INSTITUTION) ANGUCHETTYPALAYAM, PANRUTI 607 110. EE6504 ELECTRICAL MACHINES - II UNIT I SYNCHRONOUS GENERATOR PART A 1. What

More information

UNIT-I ALTERNATORS PART-A

UNIT-I ALTERNATORS PART-A UNIT-I ALTERNATORS 1. What principle is used in Alternators? 2. What are the requirements of an alternator? 3. Mention the types of alternator rotor. 4. What is hunting in alternators? 5. What are the

More information

The Wound-Rotor Induction Motor Part II

The Wound-Rotor Induction Motor Part II Experiment 2 The Wound-Rotor Induction Motor Part II OBJECTIVE To determine the starting characteristics of the wound-rotor induction motor. To observe the rotor and stator currents at different motor

More information

10. Starting Method for Induction Motors

10. Starting Method for Induction Motors 10. Starting Method for Induction Motors A 3-phase induction motor is theoretically self starting. The stator of an induction motor consists of 3-phase windings, which when connected to a 3-phase supply

More information

ELECTRICAL MACHINES-II LABORATORY MANUAL

ELECTRICAL MACHINES-II LABORATORY MANUAL ELECTRICAL MACHINES-II LABORATORY MANUAL T. ANIL KUMAR Associate Professor Department of Electrical and Electrical Engineering N. SINDHU Assistant Professor Department of Electrical and Electrical Engineering

More information

DHANALAKSHMI COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING ME 6351 ELECTRICAL DRIVES AND CONTROL UNIVERSITY QUESTIONS AND ANSWERS

DHANALAKSHMI COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING ME 6351 ELECTRICAL DRIVES AND CONTROL UNIVERSITY QUESTIONS AND ANSWERS DHANALAKSHMI COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING ME 6351 ELECTRICAL DRIVES AND CONTROL UNIVERSITY QUESTIONS AND ANSWERS 1) What is the Necessity of starter? UNIT 3 Two Marks Both

More information

ELECTRICAL AND ELECTRONICS LABORATROY MANUAL

ELECTRICAL AND ELECTRONICS LABORATROY MANUAL ELECTRICAL AND ELECTRONICS LABORATROY MANUAL K CHAITANYA Assistant Professor Department of Electrical and Electrical Engineering A. NARESH KUMAR Assistant Professor Department of Electrical and Electrical

More information

SIMULINK Based Model for Determination of Different Design Parameters of a Three Phase Delta Connected Squirrel Cage Induction Motor

SIMULINK Based Model for Determination of Different Design Parameters of a Three Phase Delta Connected Squirrel Cage Induction Motor IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 7, Issue 4 (Sep. - Oct. 2013), PP 25-32 SIMULINK Based Model for Determination of Different

More information

Synchronous Motor Drives

Synchronous Motor Drives UNIT V SYNCHRONOUS MOTOR DRIVES 5.1 Introduction Synchronous motor is an AC motor which rotates at synchronous speed at all loads. Construction of the stator of synchronous motor is similar to the stator

More information

Instructor. Payam Zarbakhsh. Department of electrical electronics engineering

Instructor. Payam Zarbakhsh. Department of electrical electronics engineering Instructor Payam Zarbakhsh Department of electrical electronics engineering Electrical Machines Induction Motors_Note(1) Comparing with synchronous motor No dc field current is required to run the machine.

More information

UNIT-1 Drive Characteristics

UNIT-1 Drive Characteristics UNIT-1 Drive Characteristics DEFINITION: Systems employed for motion control are called as DRIVES Drives may employ any of the prime movers such as diesel or petrol engine, gas or steam turbines, steam

More information

CHAPTER 5 FAULT AND HARMONIC ANALYSIS USING PV ARRAY BASED STATCOM

CHAPTER 5 FAULT AND HARMONIC ANALYSIS USING PV ARRAY BASED STATCOM 106 CHAPTER 5 FAULT AND HARMONIC ANALYSIS USING PV ARRAY BASED STATCOM 5.1 INTRODUCTION Inherent characteristics of renewable energy resources cause technical issues not encountered with conventional thermal,

More information

ROTATING MAGNETIC FIELD

ROTATING MAGNETIC FIELD Chapter 5 ROTATING MAGNETIC FIELD 1 A rotating magnetic field is the key to the operation of AC motors. The magnetic field of the stator is made to rotate electrically around and around in a circle. Stator

More information

Fall 1997 EE361: MIDTERM EXAM 2. This exam is open book and closed notes. Be sure to show all work clearly.

Fall 1997 EE361: MIDTERM EXAM 2. This exam is open book and closed notes. Be sure to show all work clearly. NAME: STUDENT NUMBER: Fall 1997 EE361: MIDTERM EXAM 2 This exam is open book and closed notes. Be sure to show all work clearly. 1. 10 points - Mechanical and Electrical Energy Relationships: A dc motor

More information

Electrical Machines-I (EE-241) For S.E (EE)

Electrical Machines-I (EE-241) For S.E (EE) PRACTICAL WORK BOOK For Academic Session 2013 Electrical Machines-I (EE-241) For S.E (EE) Name: Roll Number: Class: Batch: Department : Semester/Term: NED University of Engineer ing & Technology Electrical

More information

INDUCTION MOTOR. There is no physical electrical connection to the secondary winding, its current is induced

INDUCTION MOTOR. There is no physical electrical connection to the secondary winding, its current is induced INDUCTION MOTOR INTRODUCTION An induction motor is an alternating current motor in which the primary winding on one member (usually the stator) is connected to the power source and a secondary winding

More information

SRM Institute of Science and Technology (Deemed to be University)

SRM Institute of Science and Technology (Deemed to be University) 5EE0L-ELECTRICAL MACHINES LAB-II RECORD ACADEMIC YEAR: ODD SEMESTER 08-9 NAME : REG.NO. : DEPARTMENT OF ELECTRICAL & ELECTRONICS ENGINEERING FACULTY OF ENGINEERING & TECHNOLOGY SRM Institute of Science

More information

CHAPTER 4 MODELING OF PERMANENT MAGNET SYNCHRONOUS GENERATOR BASED WIND ENERGY CONVERSION SYSTEM

CHAPTER 4 MODELING OF PERMANENT MAGNET SYNCHRONOUS GENERATOR BASED WIND ENERGY CONVERSION SYSTEM 47 CHAPTER 4 MODELING OF PERMANENT MAGNET SYNCHRONOUS GENERATOR BASED WIND ENERGY CONVERSION SYSTEM 4.1 INTRODUCTION Wind energy has been the subject of much recent research and development. The only negative

More information

DC CIRCUITS ELECTROMAGNETISM

DC CIRCUITS ELECTROMAGNETISM DC CIRCUITS 1. State and Explain Ohm s Law. Write in brief about the limitations of Ohm s Law. 2. State and explain Kirchhoff s laws. 3. Write in brief about disadvantages of series circuit and advantages

More information

ELECTRICAL MACHINES I

ELECTRICAL MACHINES I PRACTICAL WORK BOOK ELECTRICAL MACHINES I EX-404 Name: Enrollment No: Branch: Semester: Batch: Department of Electrical Engineering Name of Laboratory : Electrical Machine - I Lab Subject Code : Ex 404

More information

Pretest Module 21 Unit 4 Single-Phase Motors

Pretest Module 21 Unit 4 Single-Phase Motors Pretest Module 21 Unit 4 Single-Phase Motors 1. What are the four main components of a single-phase motor? Rotor, stator, centrifugal switch, end bells and bearings 2. How is a rotating field created in

More information

The Wound-Rotor Induction Motor Part III

The Wound-Rotor Induction Motor Part III Experiment 5 The Wound-Rotor Induction Motor Part III OBJECTIVE To observe the characteristics of the wound-rotor induction motor at no-load and full-load. To observe speed control using an external variable

More information

POWER SUPPLY FOR ASYNCHRONOUS MOTORS

POWER SUPPLY FOR ASYNCHRONOUS MOTORS White Paper 07 2010 POWER SUPPLY FOR ASYNCHRONOUS MOTORS Author: Franck Weinbissinger GENERAL INFORMATION Three-phase asynchronous motors are very robust and low-maintenance electrical machines widely

More information

EXPERIMENT 2 THREE PHASE INDUCTION MOTOR, PART 1

EXPERIMENT 2 THREE PHASE INDUCTION MOTOR, PART 1 University f Jordan School of Engineering Department of Mechatronics Engineering Electrical Machines Lab Eng. Osama Fuad Eng. Nazmi Ashour EXPERIMENT 2 THREE PHASE INDUCTION MOTOR, PART 1 OBJECTIVES To

More information

Design and dimensions calculation of Inductive Rheostat as a Control Element of Synchronization Systems

Design and dimensions calculation of Inductive Rheostat as a Control Element of Synchronization Systems Australian Journal of Basic and Applied Sciences, 3(4): 3778-3785, 2009 ISSN 1991-8178 Design and dimensions calculation of Inductive Rheostat as a Control Element of Synchronization Systems Ali S. Akayleh

More information

Contents. Review of Electric Circuitd. Preface ;

Contents. Review of Electric Circuitd. Preface ; Preface ; Chapter 1 Review of Electric Circuitd 1.1 Introduction, 1 1.2 Direct Circuit Current, 1 1.2.1 Voltage, 3 1.2.2 Power, 3 1.2.3 Ohm's Law, 5 1.2.4 KirchhofTs Laws, 5 1.2.4.1 Kirchhoff s Current

More information

SRI VIDYA COLLEGE OF ENGINEERING & TECHNOLOGY QUESTION BANK UNIT III EC6352-ELECTRICAL ENGINEERING AND INSTRUMENTATION UNIT III PART A

SRI VIDYA COLLEGE OF ENGINEERING & TECHNOLOGY QUESTION BANK UNIT III EC6352-ELECTRICAL ENGINEERING AND INSTRUMENTATION UNIT III PART A SRI VIDYA COLLEGE OF ENGINEERING & TECHNOLOGY QUESTION BANK UNIT III EC6352-ELECTRICAL ENGINEERING AND INSTRUMENTATION UNIT III PART A INDUCTION MOTORS 1. What are the 2 types of 3phase induction motor?

More information

EXPERIMENT 19. Starting and Synchronizing Synchronous Machines PURPOSE: BRIEFING: To discover the method of starting synchronous motors.

EXPERIMENT 19. Starting and Synchronizing Synchronous Machines PURPOSE: BRIEFING: To discover the method of starting synchronous motors. EXPERIMENT 19 Starting and Synchronizing Synchronous Machines PURPOSE: To discover the method of starting synchronous motors. BRIEFING: When three-phase is applied to the stator of a three-phase motor,

More information

Types of Electric Motors

Types of Electric Motors Types of Electric Motors Electric Motors DC Motors AC Motors Other Motors Shunt motor Separately Excited motor Induction motor Stepper motor Brushless DC motor Series Motor Permanent Magnet DC (PMDC) Synchronous

More information

Motor Basics AGSM 325 Motors vs Engines

Motor Basics AGSM 325 Motors vs Engines Motor Basics AGSM 325 Motors vs Engines Motors convert electrical energy to mechanical energy. Engines convert chemical energy to mechanical energy. 1 Motors Advantages Low Initial Cost - $/Hp Simple &

More information

Electrical Machines II. Week 5-6: Induction Motor Construction, theory of operation, rotating magnetic field and equivalent circuit

Electrical Machines II. Week 5-6: Induction Motor Construction, theory of operation, rotating magnetic field and equivalent circuit Electrical Machines II Week 5-6: Induction Motor Construction, theory of operation, rotating magnetic field and equivalent circuit Asynchronous (Induction) Motor: industrial construction Two types of induction

More information

EMC Issues in Electric Drives

EMC Issues in Electric Drives EMC Due to: Control systems requirements. Motor operation. Physical constraints. Scaling of EMC Methods to Electric Drive Analysis. New Developments / Future Methods Why Use Electric Drives? Advances in

More information

5. The force required to bring an object weighing 65 lb from rest to a speed of 50 fps in 10 sec is approximately

5. The force required to bring an object weighing 65 lb from rest to a speed of 50 fps in 10 sec is approximately Student ID: 53703105 Exam: 4341RR - Industrial Motor Applications When you have completed your exam and reviewed your answers, click Submit Exam. Answers will not be recorded until you hit Submit Exam.

More information

Rotor Side Speed Control Methods Using MATLAB/Simulink for Wound Induction Motor

Rotor Side Speed Control Methods Using MATLAB/Simulink for Wound Induction Motor Rotor Side Speed Control Methods Using MATLAB/Simulink for Wound Induction Motor Rajesh Kumar, Roopali Dogra, Puneet Aggarwal Abstract In recent advancements in electric machine and drives, wound rotor

More information

Modeling and Simulation of a Large Chipper Drive

Modeling and Simulation of a Large Chipper Drive I I Modeling and Simulation of a Large Chipper Drive Modeling and Simulation of a Large Chipper Drive Hansjörg Kapeller Anton Haumer Christian Kral Gert Pascoli Franz Pirker arsenal research Giefinggasse

More information

INDUCTION MOTORS 1. OBJECTIVE 2. SAFETY

INDUCTION MOTORS 1. OBJECTIVE 2. SAFETY INDUCTION MOTORS 1. OBJECTIE To study a 3-phase induction motor, by using its experimentally developed equivalent circuit diagram and by obtaining its basic characteristics: torque/slip, current/slip and

More information

Lab 6: Wind Turbine Generators

Lab 6: Wind Turbine Generators Lab 6: Wind Turbine Generators Name: Pre Lab Tip speed ratio: Tip speed ratio (TSR) is defined as: Ω, where Ω=angular velocity of wind, and R=radius of rotor (blade length). If the rotational speed of

More information

To discover the factors affecting the direction of rotation and speed of three-phase motors.

To discover the factors affecting the direction of rotation and speed of three-phase motors. EXPERIMENT 12 Direction of Rotation of Three-Phase Motor PURPOSE: To discover the factors affecting the direction of rotation and speed of three-phase motors. BRIEFING: The stators of three-phase motors

More information

Single Phase Induction Motor. Dr. Sanjay Jain Department Of EE/EX

Single Phase Induction Motor. Dr. Sanjay Jain Department Of EE/EX Single Phase Induction Motor Dr. Sanjay Jain Department Of EE/EX Application :- The single-phase induction machine is the most frequently used motor for refrigerators, washing machines, clocks, drills,

More information

Investigation of the Operational Behavior of a Large Chipper Drive

Investigation of the Operational Behavior of a Large Chipper Drive Investigation of the Operational Behavior of a Large Chipper Drive H. Kapeller, A. Haumer, C. Kral, C. Grabner Abstract This paper presents two simulation models for two variants of a large chipper drive

More information

CHAPTER 1 INTRODUCTION

CHAPTER 1 INTRODUCTION 1 CHAPTER 1 INTRODUCTION 1.1 MOTIVATION OF THE RESEARCH Electrical Machinery is more than 100 years old. While new types of machines have emerged recently (for example stepper motor, switched reluctance

More information

Single Phase Induction Motors

Single Phase Induction Motors Single Phase Induction Motors Prof. T. H. Panchal Asst. Professor Department of Electrical Engineering Institute of Technology Nirma University, Ahmedabad Introduction As the name suggests, these motors

More information

Revised October 6, EEL 3211 ( 2008, H. Zmuda) 6. Induction Motors 1

Revised October 6, EEL 3211 ( 2008, H. Zmuda) 6. Induction Motors 1 Induction Motors Revised October 6, 008 EEL 311 ( 008, H. Zmuda) 6. Induction Motors 1 Induction Motors: We just learned how damper or amortisseur windings on a synchronous motor could develop a starting

More information

PHY 152 (ELECTRICITY AND MAGNETISM)

PHY 152 (ELECTRICITY AND MAGNETISM) PHY 152 (ELECTRICITY AND MAGNETISM) ELECTRIC MOTORS (AC & DC) ELECTRIC GENERATORS (AC & DC) AIMS Students should be able to Describe the principle of magnetic induction as it applies to DC and AC generators.

More information

A Dual Stator Winding-Mixed Pole Brushless Synchronous Generator (Design, Performance Analysis & Modeling)

A Dual Stator Winding-Mixed Pole Brushless Synchronous Generator (Design, Performance Analysis & Modeling) A Dual Stator Winding-Mixed Pole Brushless Synchronous Generator (Design, Performance Analysis & Modeling) M EL_SHANAWANY, SMR TAHOUN& M EZZAT Department (Electrical Engineering Department) University

More information

Question Bank. Write the relationship between speed and frequency for 3 phase induction 3 motor.

Question Bank. Write the relationship between speed and frequency for 3 phase induction 3 motor. Course B.E(EEE-Marine) Batch 17 Semester VII Subject code EE1706 subject Name Marine Electrical System Design & Layout PART-A Marks: 2 UNIT-1 Question Bank 1 Write the comparison of A.C. over D.C.? 2 Why

More information