Rev Serial# Current

Transcription

1 PRAIRIE CLIPPER ROTARY CUTTER Rev Serial# Current Part No P PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or M&W ( ) to obtain a Free copy before operating the equipment. MODEL PC828A M&W 1020 South Sangamon Ave. Gibson City, Illinois Alamo Group Inc.

2 TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.

3 Parts Section 1 PARTS SECTION

4 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Group Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: M&W 1020 South Sangamon Ave. Gibson City, Illinois Alamo Group Inc. Parts Section 2

5 PART NAME INDEX A-FRAME ASSEMBLY AXLE & CONTROL ROD ASSEMBLY - PULL TYPE AXLE ASSEMBLY - SEMI MOUNT BLADE PAN ASSEMBLY CASTER FORK & WHEEL ASSEMBLY S/N CURRENT CHAIN GUARD ASSEMBLY - FRONT CHAIN GUARD ASSEMBLY - REAR CUTTING HEAD ASSEMBLY Rev CYLINDER, HYDRAULIC LIFT P/N CYLINDER, HYDRAULIC LIFT P/N 8727A DEFLECTOR ASSEMBLY - FRONT DEFLECTOR ASSEMBLY - REAR DRIVELINE - LIFT TYPE & SEMI-MOUNT 540 RPM P/N DRIVELINE - LIFT TYPE 540 RPM P/N DRIVELINE - OUTER P/N S/N BELOW Pub DRIVELINE - PULL TYPE 1000 RPM P/N A... 7 DRIVELINE - PULL TYPE 540 RPM P/N A... 6 DRIVELINE -OUTER P/N S/N CURRENT Pub DRIVELINE PULL TYPE 540 RPM EQ ANGLE P/N GEARBOX ASSEMBLY DIVIDER P/N GEARBOX ASSEMBLY DIVIDER P/N Rev GEARBOX ASSEMBLY OUTER P/N GEARBOX ASSEMLBY OUTER P/N JACKSHAFT PULL TYPE P/N JACKSHAFT PULL TYPE P/N JACKSHAFT SUPPORT - PULL TYPE LIFT ARRANGEMENTS SAFETY DECAL LOCATION LIFT TYPE SAFETY DECAL LOCATION PULL TYPE SHIELD ASSEMBLY S/N Below Pub SHIELD ASSEMBLY S/N Current Pub SLIP CLUTCH ASSEMBLY P/N SLIP CLUTCH ASSEMBLY P/N SPRING SHOCK ASSEMBLY (OPTIONAL) TAIL WHEEL HUB ASSEMBLY S/N CURRENT TAILWHEEL ASSEMBLY - LIFT TYPE S/N BELOW TAILWHEEL ASSEMBLY - LIFT TYPE S/N CURRENT TIRE & WHEEL ASSEMBLY TONGUE ASSEMBLY Alamo Group Inc. Parts Section 3

6 DRIVELINE - LIFT TYPE & SEMI-MOUNT 540 RPM P/N DRIVELINE LG.X1-3/8 6OD HALF DRIVE SHAFT W/YOKE DRIVE SHAFT HALF W/CLUTCH CLUTCH & YOKE SERIES CROSS BEARING SERIES YOKE INNER # TUBE, HT INNER D/L-680MM LG GREASE FTG.ELBOW 8MMP TUBE-OUTER D/L 670MM LG PIN-ROLL #6 10MM X 75MM OUTER YOKE-OUTER TUBE # YOKE, SLIDE COLLAR KIT-SLIDE COLLAR REPAIR LOCKING COLLAR OUTER SHIELD LOCKING COLLAR INNER SHIELD BOLT, NYLON - SAFETY SHIELD] SHIELD KIT COMPL SHIELD KIT OUTER SHIELD KIT INNER BUSHING WITH GREASE NIPPLE 2005 Alamo Group Inc. Parts Section 4

7 DRIVELINE - LIFT TYPE 540 RPM P/N DRIVELINE 540 RPM SE YOKE 1-3/8-6 SPLINE ASGE 2 W279R 2 CROSS REPAIR KIT, CTR SPRING PIN 10MM X 90MM YOKE INBOARD 1B PROFILE INNER 780MM TUBE & SLEEVE YOKE INBOARD 2A FRICTION CLUTCH BEARING RING USE SUPPORT BEARING ZERK SHIELD, OUTER HALF SHIELD, INNER HALF YOKE.Q.D.KIT - PLASTIC FLANGE QD KIT 2005 Alamo Group Inc. Parts Section 5

8 DRIVELINE - PULL TYPE 540 RPM P/N A A D/L MAIN 540 EQ ANGLE COMPLETE COLLAR YOKE COLLAR KIT CROSS JOURNAL SET OUTER YOKE ROLL PIN FOR OUTER TUBE INNER TUBE ROLL PIN FOR INNER TUBE INNER YOKE COMPLETE CLAMP YOKE NUT & BOLT SET RETAINING COLLAR FOR INNER TUBE BOLT RETAINING COLLAR FOR OUTER TUBE OUTER SHIELD INNER SHIELD COMPLETE SHIELD 2005 Alamo Group Inc. Parts Section 6

9 DRIVELINE - PULL TYPE 1000 RPM P/N A A DRIVELINE 1000 MAIN EQ ANGLE YOKE, ASY, 1-3/8X21SPL KIT-SLIDE COLLAR REPAIR CROSS BEARING SERIES YOKE OUTER D/L A PIN-ROLL #6 10MM X 75MM OUTER TUBE INNER PIN-ROLL #6 10MM X 75MM OUTER YOKE INNER # USE BOLT & NUT,12-P1.25 X 55MM LOCKING COLLAR INNER SHIELD BOLT, NYLON - SAFETY SHIELD] LOCKING COLLAR OUTER SHIELD OUTER SHIELD HALF INNER SHIELD HALF SHIELD COMPLETE 2005 Alamo Group Inc. Parts Section 7

10 DRIVELINE PULL TYPE 540 RPM EQ ANGLE P/N DRIVELINE MAIN 540 EQ ANGLE YOKE 1-3/8-6 SPLINE ASGE 2 W279R 2 CROSS REPAIR KIT, CTR YOKE INBOARD 2A OUTER PROFILE 2A SPRING PIN 10MM X 90MM YOKE 1-3/4-20 SPL I.C SCREW 1/2 LG END BEARING RING BOLT P1.75 M12 X NUT P1.75 M OUTER SHIELD HALF INNER SHIELD HALF YOKE.Q.D.KIT - PLASTIC 2005 Alamo Group Inc. Parts Section 8

11 SLIP CLUTCH ASSEMBLY P/N CLUTCH & YOKE SERIES YOKE, FLANGED CLUTCH BODY PRESSURE PLATE PLATE WITH HOLES RING,CLUTCH LINING BUSHING SPRING CLUTCH BOLT M12 x 1.25 x 65 & NUT BOLT & NUT M10X95 SELF LK NUT INNER PLATE 2005 Alamo Group Inc. Parts Section 9

12 SLIP CLUTCH ASSEMBLY P/N FRICTION CLUTCH YOKE, FLANGE RING,CLUTCH LINING HUB 1 3/8-6-QD PLATE, THRUST SPRING, BELLEVILLE HEX BOLT M10 X HEX LOCKNUT M FLANGE QD KIT 2005 Alamo Group Inc. Parts Section 10

13 JACKSHAFT PULL TYPE P/N DRIVELINE, JACKSHAFT ASSY-OUTER HALF D/L W SHIELD & TUBE-OUTER D/L 715MM LG PIN-ROLL #6 10MM X 75MM OUTER YOKE-OUTER TUBE # CROSS BEARING SERIES CLUTCH & YOKE SERIES LOCKING COLLAR OUTER SHIELD BOLT, NYLON - SAFETY SHIELD] LOCKING COLLAR INNER SHIELD KIT- COMP. SHIELD TUBE, INNER W/1-3/4-20 STUB GREASE FITTING FOR TUBE SPRING,CENTERING GREASE FTG.ELBOW 8MMP Alamo Group Inc. Parts Section 11

14 JACKSHAFT PULL TYPE P/N DRIVELINE, 540 RPM SE8 1 W279R 1 CROSS REPAIR KIT, CTR SPRING PIN 10MM X 90MM PROFILE & SLEEVE YOKE INBOARD 2A FRICTION CLUTCH BEARING RING USE SUPPORT BEARING ZERK OUTER SHIELD HALF INNER SHIELD HALF FLANGE QD KIT 2005 Alamo Group Inc. Parts Section 12

15 JACKSHAFT SUPPORT - PULL TYPE WLDMT-JACKSHAFT BRG SUPT HEXB 1/2 NC 7 PL HEXB 5/8 NC 2 PL BEARING&HOUSING ASSY PIPE-SPACER BUSHING 7/8 X.635 X 21/ WASHER,5/8 HARDENED LOCKNUT LOCKNUT 2005 Alamo Group Inc. Parts Section 13

16 TONGUE ASSEMBLY 2005 Alamo Group Inc. Parts Section 14

17 TONGUE ASSEMBLY FLATWASHER LOCKNUT DRIVELINE JACKSHAFT WLDMT TONGUE WLDMT-JACKSHAFT BRG SUPT PIPE-SPACER BEARING&HOUSING ASSY WASHER,5/8 HARDENED HHCS 1 NC 4 GR NUT TOPLOCK 1 NC PLB WASHER-HITCH CLEVIS CLEVIS WELDMENT SPRING WASHER BOLT 1-8UNC-6 LG GRD BUSHING 7/8 X.635 X 21/ HEXB 5/8 NC 2 PL HEXB 1/2 NC 7 PL5 18 5JRC NUT TOPLOCK 7/8 NC PLB FLATWASHER 7/8 PL STD ORDER 580 MIN HT BUSHING HHCS 7/8-9UNC 2-1/2 GR BOLT HOSE HOLDER ASSY DRIVELINE 540 MAIN EQ ANGLE CHAIN-SAFETY TOW-6000 LB. CAP JACK PARKING 3000LB SIDEWIND LOCKNUT 2005 Alamo Group Inc. Parts Section 15

18 A-FRAME ASSEMBLY PIN WRIST HHCS,3/4NC X 2,ZP,GRD B12 1 PIN TOP LINK CAT 1(PLATED) BUSHING TOP LINK BAR,A-FRAME SHORT B13 1 CLIP-X HAIR PIN BAR TOP LINK BD BUSHING 1-1/4X7/32X3 A-FRAME BAR FRONT STRAP B 1 PIN-HINGE CAP HEXB 3/4 NC 6LG GR BOLT BAR,REAR SUPPORT LOCKNUT 2005 Alamo Group Inc. Parts Section 16

19 BLADE PAN ASSEMBLY BLADE PAN ASSEMBLY - LH BLADE PAN ASSEMBLY - RH BLADE PAN WELDMENT SUCTION BLADE CLOCKWISE - RH ASSY SUCTION BLADE COUNTER CLOCKWISE - LH ASSY BLADE BOLT WASHER TOPLOCK 2005 Alamo Group Inc. Parts Section 17

20 GEARBOX ASSEMLBY OUTER P/N Alamo Group Inc. Parts Section 18

21 GEARBOX ASSEMLBY OUTER P/N GEARBOX, 1-3/ W/LUBE SHIM HEX BOLT M8X22,T4A GEAR BOX PLUG,1/ COVER PLATE GEAR, CROW Z21 M BEARING GEARBOX CASTING AND MACHINING SNAP RING 72 UNI SEAL, INPUT SHAFT 35X72X SHAFT 1 3/8 Z NUT-METRIC OUTPUT SHAFT M30X GEAR, CONIC PIGNON Z14 M SHIM BEARING,TIMKEN OIL SEAL PROTECTIVE SHIELD PIN, COTTER OUTPUT SHAFT WASHER OD DX NUT PLUG,3/ BEARING CAP PLUG 72 X SHIM PLUG HUB, BUSHING GROOVED COTTER PIN PLUG,1/2 PRESSURIZED VENT USE ON MODEL SERIAL NUMBERS AND ABOVE 2005 Alamo Group Inc. Parts Section 19

22 GEARBOX ASSEMBLY OUTER P/N Alamo Group Inc. Parts Section 20

23 GEARBOX ASSEMBLY OUTER P/N ASSY,OUTER GEARBOX W/LUBE HOUSING,OUTER GEARBOX CAP,OUTPUT CAP,INPUT W/MOUNTING HOLES GEAR,INPUT (1:1.47) 22T PINION,OUTPUT (1:1.47) 15T SHAFT,INPUT 1-3/8-21 SPLINE BALL BEARING BALL BEARING BEARING CONE BEARING CUP TIMKEN #362A BEARING CUP SEAL,INPUT 3-LIP SEAL,OUTPUT 3-LIP var. GASKET,INPUT 0.30MM var. GASKET,INPUT 0.15MM var. GASKET,INPUT 0.10MM var. GASKET,OUTPUT O.30MM var. GASKET,OUTPUT 0.15MM var. GASKET,OUTPUT 0.10MM SPACER COTTER PIN BOLT NUT,1-14 FLANGED HEX SLOTTED LOCKWASHER,3/8,MEDIUM-ZP PIPE PLUG PLUG,1/2 PRESSURIZED VENT SNAP RING SNAP RING SNAP RING USE ON MODEL SERIAL NUMBERS AND BELOW 2005 Alamo Group Inc. Parts Section 21

24 GEARBOX ASSEMBLY DIVIDER P/N Alamo Group Inc. Parts Section 22

25 GEARBOX ASSEMBLY DIVIDER P/N ASSY,DIVIDER GEARBOX W/LUBE HOUSING,DIVIDER GEARBOX SE CAP-OUTPUT, W/SHIELD HOLES CAP-INPUT, W/SHIELD HOLES GEAR-17T GEAR-14T SHAFT-INPUT,1-3/8-6A SHAFT-CROSS, 1-3/ BEARING CONE BEARING CONE TIMKEN #LM BEARING CUP BEARING CUP TIMKEN #362A CUP BEARING OIL SEAL OIL SEAL var. GASKET-OUTPUT CAP, 0.30MM var. GASKET-OUTPUT CAP, 0.15MM var. GASKET-OUTPUT CAP, 0.10MM var. GASKET-INPUT CAP, 0.25MM var. GASKET-INPUT CAP, 0.15MM var. GASKET-INPUT CAP, 0.10MM SPACER var. SHIM-0.25MM HHCS 3/8-16X1.25 GR HHCS 1/2NC 1-1/ LOCKWASHER,3/8,MEDIUM-ZP LOCK WASHER SNAP RING PLUG, PIPE, SQ HD PLUG 1/8 NPT SQUARE HEAD PLUG,1/2 PRESSURIZED VENT USE ON MODEL SERIAL NUMBERS AND BELOW 2005 Alamo Group Inc. Parts Section 23

26 GEARBOX ASSEMBLY DIVIDER P/N Rev Alamo Group Inc. Parts Section 24

27 GEARBOX ASSEMBLY DIVIDER P/N Rev DIVIDERBOX, 1:1.21 SU 540 W/LU CASTING, DIVIDERBOX LOCKNUT&METRIC INPUT SHAFT M BOLT SHAFT, THROUGH 1-3/8 Z SHIM 45.3 X GEAR, PINION Z22.M GEAR-INPUT 28 TOOTH SHIM 40.3x51.5x PARALLEL KEY B 14 X 9 X DUST LIP 45x72x COVER PLATE ROLLER BEARING x85x SHAFT 1-3/8 Z EXTENSION BEARING OIL SEAL 52x85x SHIM PLUG GEAR, CROWN Z27 M VENT PLUG 3/8 USE ON MODEL SERIAL NUMBERS AND ABOVE 2005 Alamo Group Inc. Parts Section 25

28 CUTTING HEAD ASSEMBLY Rev Alamo Group Inc. Parts Section 26

29 CUTTING HEAD ASSEMBLY Rev WLDMT, DECK SE8A DIVIDERBOX, 1:1.21 SU 540 W/LU GEARBOX, 1-3/ W/LUBE ASY-DRIVELINE COUPLER 1-3/ SKID SHOE PLOW #3 3/8 NC 1 PL NUT, LOCK 3/8-16 FLG WHIZ WLDMT, BLADEPAN BLADE,SUCTION C/CW BLADE CLOCKWISE SUCTION BLADE BOLT 7/8 DIA X 3 LG WASHER-7/8 STR PLAIN NUT TOPLOCK 7/8 NF PLC NUT HEXB,5/8 NC X 2-1/4 GRD5 ZP HHCS 5/8-11UNC 1-1/2 PL SQSS 3/8-16NC 1 PL NUT 3/8 NC HEX JAMNUT LOCKWASHER FLATWASHER 2005 Alamo Group Inc. Parts Section 27

30 DRIVELINE -OUTER P/N S/N CURRENT Pub DRIVELINE OUTER DOUBLE FLEX YOKE & TUBE ASSEMBLY DISC,RUBBER (W/O BUSHINGS) A 24 WASHER,BEADED D/L COUPLER BUSHING,RUBBER DISK A 2 SPIDER, W/1-3/8-21 SPLINE SE HEXB,5/8NC X 2-1/2,ZP,GRD NUT MET TLE 16MM-P2.0 PL GREASE FITTING,8MMX1 STRAIGHT 2005 Alamo Group Inc. Parts Section 28

31 DRIVELINE - OUTER P/N S/N BELOW Pub ASY-DRIVELINE COUPLER 1-3/ WLDMT,SLEEVE D/L COUPLER SE DISC,RUBBER (W/O BUSHINGS) A 1 SPIDER, W/1-3/8-21 SPLINE SE NUT MET TLE 16MM-P2.0 PL HEXB METRIC 16-P2.0-65MM NUT METRIC 10MM-P1.5 PL HHCS, M10X1.5X A 12 WASHER,BEADED D/L COUPLER BUSHING,RUBBER DISK GREASE FITTING,8MMX1 STRAIGHT 2005 Alamo Group Inc. Parts Section 29

32 TAILWHEEL ASSEMBLY - LIFT TYPE S/N CURRENT WLDMT TAILWHEEL TUBE LOCKNUT TLM 1/2 NC PLB R 2 BRACKET WLDMT TAILWHEEL BRKT HHCS 1/2-13UNC 1-1/2 PL NUT,TOPLOCK 5/8 NC PLB HEXB,5/8NC X 3-1/2,ZP,GRD HHCS 1/2-13UNC 1-1/4 PL AG SE CASTER FORK WHEEL ASSY 2005 Alamo Group Inc. Parts Section 30

33 CASTER FORK & WHEEL ASSEMBLY S/N CURRENT AG SE CASTER FORK WHEEL ASSY H 1 WHEEL & TIRE ASSY HUB 4 BOLT WASHER FLAT 026 X 044 X 4 FLAT FORK CASTER ASSEMBLY PIN-COTTER 1/4 X 2-1/ B000 1 N/A 2005 Alamo Group Inc. Parts Section 31

34 TAIL WHEEL HUB ASSEMBLY S/N CURRENT PIN,COTTER 5/32X2-1/2 PL BUSHING SPINDLE STEP DUST CAP NIPPLE, GREASE M8X BOLT SPINDLE M24 X 2 X NUT SPINDLE M24 X BEARING LUG BOLT FLAT WASHER BOLT M12 X 1.5 X SEAL OIL 40 X 62 X Alamo Group Inc. Parts Section 32

35 TAILWHEEL ASSEMBLY - LIFT TYPE S/N BELOW WLDMT TAILWHEEL TUBE LOCKNUT R 2 BRACKET WLDMT TAILWHEEL BRKT HHCS 1/2-13UNC 1-1/2 PL LOCKNUT HEXB,5/8NC X 3-1/2,ZP,GRD HHCS 1/2-13UNC 1-1/4 PL WLDMT SPINDLE, SE TIRE & WHEEL ASSY SPACER 12 5JRC LOCKNUT 1-14 TLDT GC ZP COTTER PIN WLDMT CASTER FORK BUSHING 1-7/8 OD X 1-1/4 ID 2005 Alamo Group Inc. Parts Section 33

36 AXLE & CONTROL ROD ASSEMBLY - PULL TYPE TIRE & WHEEL ASSY SPACER 3 5JRC LOCKNUT 1-14 TLDT GC ZP WLDMT SPINDLE, SE WLDMT AXLE HEXB 3/4-10UNC 2 PL R 2 BUSHING 1 OD X.76 ID.45 LG 8 15B WASHER 3/4 P SAE LOCKNUT PIN-COTTER 3/16 X 1-1/2 PLATED PIN-DRILLED ROD,CONTROL 13 5C HEXNUT 7/8 JAM ZP DO NOT REORDER/DEPLETE STOCK CONTROL ROD WELD WLDMT TONGUE 2005 Alamo Group Inc. Parts Section 34

37 CYLINDER, HYDRAULIC LIFT P/N HYDRAULIC CYLINDER, T CAP (HYD. CYLINDER) HEAD PISTON 2-1/2 BORE PISTON ROD TUBE (HYD. CYLINDER) TIE ROD BOLT HEX NUT SEAL KIT ref PIN-HYD. CYLINDER ref COTTER PIN CLEVIS,OUTER NUT HEX 3/8 NF PL N/A-ADD M OR W BREATHER, CYLINDER ref HOSE #6-8MP - 8MP - 144LG ref ADAPTER, HYD, ELBOW SWIVEL 2005 Alamo Group Inc. Parts Section 35

38 CYLINDER, HYDRAULIC LIFT P/N 8727A 8727A COMPLETE ASSEMBLY CLEVIS CAP ROD CAP PISTON ROD TUBE TIE ROD SEAL KIT NYLON THREAD PROTECTOR ROD CLEVIS SET SCREW H5C 8 TIE ROD NUT 19 5JRC PISTON NUT PORT PLUG BREATHER ref HOSE (NOT SHOWN) ref ELBOW (NOT SHOWN) ref ADAPTER (NOT SHOWN) ref PIN (NOT SHOWN) ref COTTER PIN (NOT SHOWN) 2005 Alamo Group Inc. Parts Section 36

39 SPRING SHOCK ASSEMBLY (OPTIONAL) ASSY,SPRING SHOCK (BLACK) WLDMT SPRING SHOCK SR WLDMT ANGLE BKT L/H SR WLDMT ANGLE BKT R/H SR A 2 SPRING HHCS 1 NC 2-3/4 GR PIN-HYD. CYLINDER FLATWASHER 1 PL STD COTTER PIN NUT TOPLOCK 1 NC PLB HEXB,5/8NC X 2-1/2,ZP,GRD TUBE-SPACER LOCKNUT 2005 Alamo Group Inc. Parts Section 37

40 TIRE & WHEEL ASSEMBLY TIRE & WHEEL ASSY TIRE/WHL. W/CUPS(BREAK DOWN CUP, BEARING BEARING CONE SEAL 2005 Alamo Group Inc. Parts Section 38

41 DEFLECTOR ASSEMBLY - FRONT DEFLECTOR, ASY, FRT SHIELD DEFLECTOR FRONT BAR SHIELD SUPPORT SHIELD,FRONT DEFLECTOR FLAT, FRONT DEFLECTOR SUPPORT HHCS 1/2-13UNC 1-1/4 PL FLATWASHER NUT 2005 Alamo Group Inc. Parts Section 39

42 DEFLECTOR ASSEMBLY - REAR DEFLECTOR, ASY, RER SHIELD DEFLECTOR CENTER BAR SHIELD SUPPORT REAR CTR SHIELD DEFLECTOR OUTER BAR REAR SUPPORT HHCS 1/2-13UNC 1-1/4 PL FLATWASHER NUT HHCS 1/2-13UNC 1-1/2 PL Alamo Group Inc. Parts Section 40

43 CHAIN GUARD ASSEMBLY - FRONT ASY,GUARD ASY,FRT CHN GDS DEG HHCS 1/2-13UNC 1-1/4 PL FLATWASHER NUT 2005 Alamo Group Inc. Parts Section 41

44 CHAIN GUARD ASSEMBLY - REAR ASY,GUARD 30 LH ASY,GUARD 30RH ASY,GUARD HHCS 1/2-13UNC 1-1/4 PL FLATWASHER NUT HHCS 1/2-13UNC 1-1/2 PL Alamo Group Inc. Parts Section 42

45 SHIELD ASSEMBLY S/N Current Pub SHIELD HOOD NUT-PLASTIC KNOB 3/8 NC PL 3 7A C/S3/8 X 1 1/4 NC ZP FLATWASHER 3/8 PL STD PUSHNUT, BOLT RETAINER, 3/ CRG-BLT 3/8 X 1 GR SHIELD BRACKET SHIELD BRACKET NUT,TOPLOCK 3/8NC PLB LOCKWASHER 5/16 PL STD HHCS 5/16NC 1 PL DIVIDER SHEILD WELDMENT 2005 Alamo Group Inc. Parts Section 43

46 SHIELD ASSEMBLY S/N Below Pub SHIELD GEARBOX 2 5F /2 NC WING NUT FLATWASHER HEXB 5/8 NC 1-1/4GR LOCKWASHER FLATWASHER WLDMT CTR GEARBOX SHIELD SUPT PLATE, SHIELD SUPPORT BRKT-HOOD FLATWASHER LOCKWASHER HHCS 5/16NC 1 PL Alamo Group Inc. Parts Section 44

47 AXLE ASSEMBLY - SEMI MOUNT WELDMENT, AXLE(RHINO) HEXB 3/4-10UNC 2 PL R 2 BUSHING 1 OD X.76 ID.45 LG 4 15B WASHER 3/4 P SAE LOCKNUT WLDMT-GAUGE WHEEL FORK TIRE & WHEEL ASSY TIRE/WHL. W/CUPS(BREAK DOWN SPACER NUT TOPLOCK 1 NC PLB SEAL BEARING BUSHING 1-7/8 OD X 1-1/4 ID PIN,ROLL 1/4 X WLDMT-BOLT 2005 Alamo Group Inc. Parts Section 45

48 LIFT ARRANGEMENTS RATCHET JACK ASSEMBLY PIN-HYD. CYLINDER PIN-COTTER 3/16 X 1-1/2 PLATED FLATWASHER 1 PL STD A 1 CYLINDER HYD 2-1/ CONTROL SPACER KIT PIN-HYD. CYLINDER COTTER PIN HOSE #6-8MP - 8MP - 144LG ADAPTER, HYD, ELBOW SWIVEL ADP HYD STGHT 8MB - 8FP 2005 Alamo Group Inc. Parts Section 46

49 NOTES 2005 Alamo Group Inc. Parts Section - 46A

50 SAFETY DECAL LOCATION LIFT TYPE 2005 Alamo Group Inc. Parts Section 47

51 SAFETY DECAL LOCATION LIFT TYPE ITEM PART NO. QTY TYPE DESCRIPTION PELIGRO SPANISH TRANSLATION DANGER MULTIHAZARD DANGER SHIELD MISSING DANGER ROTATING DRIVELINE DANGER DANGER OIL LEAK DANGER DANGER DRIVELINE IMPORTANT GENUINE RHINO PARTS 7A PELIGRO SPANISH TRANSLATION (DRIVELINE) WARNING USE/REPAIR GUARDS DANGER BLADES/THROWN OBJECTS 10 D103 1 WARNING 540 RPM REFLECT SMV REFLECT RED REFLECTOR REFLECT AMBER REFLECTOR INSTRUCT SLIP CLUTCH INSTRUCT NOTICE TO OWNER 17 D132 1 INSTRUCT BLADE TIMING 18 D137 1 INSTRUCT CCW BLADE ROTATION 19 D138 1 INSTRUCT CW BLADE ROTATION 20 D302 2 LOGO RHINO LOGO 21 D303 3 L.NAME RHINO NAME SE8 23 NFS 1 SER. PLT. SE8 SERIAL # PLATE INSTRUCT OPERATORS MANUAL INSIDE CANISTER, OPERATORS MANUAL C OPERATORS MANUAL BOLT FLATWASHER LOCKNUT 2005 Alamo Group Inc. Parts Section 48

52 SAFETY DECAL LOCATION PULL TYPE 2005 Alamo Group Inc. Parts Section 49

53 SAFETY DECAL LOCATION PULL TYPE ITEM PART NO. QTY TYPE DESCRIPTION PELIGRO SPANISH TRANSLATION DANGER MULTIHAZARD DANGER SHIELD MISSING DANGER ROTATING DRIVELINE DANGER DANGER OIL LEAK DANGER DANGER DRIVELINE IMPORTANT GENUINE RHINO PARTS 7A PELIGRO SPANISH TRANSLATION (DRIVELINE) WARNING USE/REPAIR GUARDS DANGER BLADES/THROWN OBJECTS 10 D103 1 WARNING 540 RPM REFLECT SMV REFLECT RED REFLECTOR REFLECT AMBER REFLECTOR INSTRUCT SLIP CLUTCH INSTRUCT NOTICE TO OWNER 17 D132 1 INSTRUCT BLADE TIMING 18 D137 1 INSTRUCT CCW BLADE ROTATION 19 D138 1 INSTRUCT CW BLADE ROTATION 20 D302 2 LOGO RHINO LOGO 21 D303 3 L.NAME RHINO NAME SE8 23 NFS 1 SER. PLT. SE8 SERIAL # PLATE INSTRUCT OPERATORS MANUAL INSIDE CANISTER, OPERATORS MANUAL C OPERATORS MANUAL BOLT FLATWASHER LOCKNUT 2005 Alamo Group Inc. Parts Section 50

54

55 LIMITED WARRANTY 1. LIMITED WARRANTIES 1.01.M&W warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( Purchaser ) and warrants for six months to the original commercial or industrial purchaser ( Purchaser ) that the goods purchased are free from defects in material or workmanship Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator s Manual Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase Purchaser claims must be made in writing to the Authorized Dealer ( Dealer ) from whom Purchaser purchased the goods or an approved Authorized Dealer ( Dealer ) within 30 days after Purchaser learns of the facts on which the claim is based Purchaser is responsible for returning the goods in question to the Dealer If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) (b) Repair or replace the defective goods or part(s) or Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS M&W ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. M&W Implement Model Serial Number Date Purchased Dealer ATTENTION: READ YOUR OPERATOR'S MANUAL M&W An Alamo Group Company 1020 South Sangamon Ave. Gibson City, Illinois

56 TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT ( Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and 2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.

57 PC828A Pub 07/05 Printed U.S.A. P/N P