1ZSC ABJ EN, REV. 1. Gas insulated wall bushings type GGFL Technical guide

Size: px
Start display at page:

Download "1ZSC ABJ EN, REV. 1. Gas insulated wall bushings type GGFL Technical guide"

Transcription

1 1ZSC ABJ EN, REV. 1 Gas insulated wall bushings type GGFL Technical guide

2 Original instruction The information provided in this document is intended to be general and does not cover all possible applications. Any specific application not covered should be referred directly to ABB, or its authorized representative. We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsibility whatsoever for potential errors or possible lack of information in this document. We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its contents in whole or in parts is forbidden without prior written consent of ABB.

3 Table of contents Design 5 Shed form 8 Transportation and storage 8 Long term storage 8 Testing 9 Standards 9 Routine testing 9 Type tests 9 Test tap 9 Dimensions and data 10 Electrical data 11 Dielectric losses 11 Connection details 12 Outer terminal 12 End-shields 13 Insulation gas 14 Shipping 14 Gas monitoring 15 Mechanical loading 17 Seismic tests 17 Short-time current 18 Ordering particulars 19

4

5 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE 5 Design The GGFL type wall bushing is an SF6 gasinsulated bushing intended for use in HVDC valve halls. It can also be used in AC applications. Having no oil and no condenser core gives a lightweight, yet rigid, design. The bushing was first introduced in Sylmar Converter station in Southern California It experienced and performed well during the 1994 Northridge earthquake. Later, seismic requirements were enhanced and the design improved even further by introducing a flexible bellow. The bellow stabilizes the conductor and is primarily used on larger bushings above 400 kv DC. The design is suitable for horizontal (wall bushing) as well as vertical mounting (roof bushing) and any intermediate angle. The bushing consists of an aluminum intermediate flange fitted with two composite insulators. The insulators consist of a glass fiber reinforced epoxy tube fitted with silicone rubber sheds for excellent electrical properties, also in rain and pollution conditions. The flanges of the insulators, which connect to the intermediate flange and to the cover of each high voltage end, are made of aluminum and are fastened with screws and nuts and provided with O-ring seals. The current is carried from the outdoor outer terminal through the cover via a firmly attached multiple contact or welded to a tubular aluminum conductor. There is a corresponding arrangement at the indoor end to carry the current to the indoor outer terminal. Several different studs are available for the air side connections and may be selected to properly interface to the relevant current clamp. The standard color of the composite insulator is ANSI 70 light gray. Compared to other designs with conventional condenser cores, this design gives a bushing easy to handle due to its relatively low weight. The reduced number of different materials also gives an electrically stable solution. The main gas sealing interfaces are obtained from known and proven designs from gas-insulated substations. The bushing, being of a non-condenser core type, does not demand a capacitive test tap. For applications where on-line voltage divider is requested, a capacitive test tap can be provided by introducing an isolated floating shield in the wall flange.

6 G A S I N S U L AT E D WA L L B U S H I N G S T Y P E G G F L T E C H N I C A L G U I D E 6 01 Example no. 1 of GGFL bushing design. 02 Example no. 2 of GGFL bushing design. Terminal Outdoor corona shield Cover Silicone rubber sheds Outdoor insulator Intermediate flange Fastening plane Indoor insulator Drain holes Indoor corona shield Cover Terminal Density guards Flexible bellow Rating plate Corona shield with support, only on GGFL 400 and 420, 1ZSC AAH and -AAL Rupture disc unit M12 for grounding 01 Outer terminal Cover Intermediate flange Gas valve Insulator Bursting disc 02 Rating plate

7 G A S I N S U L AT E D WA L L B U S H I N G S T Y P E G G F L T E C H N I C A L G U I D E 7 03 Example no. 3 of GGFL bushing design, with measuring tap. 04 Example no. 4 of GGFL bushing design, with mounting plane of the intermediate flange perpendicular to the bushing center axis and outer terminal with hexagon mounting surface. 03 Terminal Outdoor corona shield Cover Silicone rubber sheds Outdoor insulator Intermediate flange Indoor insulator Drain holes Cover Terminal Rupture disc unit Fastening plate Flexible bellow Indoor corona shield Rating plate 04 M20 for grounding Density guards

8 8 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE 05 Example of shed form. Shed form The standard shed form for GGFL bushings is the anti-fog type with alternating long and short sheds. The specific creepage distance, and thus the total creepage for a given flashover distance may be tailored by altering the shed profile. This is fairly easy using the extrusion method to apply silicone sheds in a helical form. ABB GGFL bushings are usually provided with one of the standard profiles giving a creepage to flashover ratio in the range of 3.3 to 3.6. Some outdoor applications have been provided with a profile exceeding ratio R R8 The specific creepage distance have ranged from 23 mm/ kv DC in the Sylmar reference installation to about mm/kv DC for some of the coastal installations. In general, silicone rubber performs better than porcelain, and the need to apply silicone grease, as has been the case for many DC installations with porcelain, is not required with silicone rubber sheds. For special customer demands regarding creepage distance, other shed forms may be used. Transportation and storage The bushing must be protected from penetrating water if stored outdoors. This means that it must not be stored in areas where it can be predicted that the ground will become wet and muddy during heavy rain. Shelter the bushing from rain and snow with a tarpaulin or roofing. The bushing is supplied with the gas volume filled with nitrogen gas (N 2 ) at a pressure of 25 kpa. This pressure should be maintained during shipping and storage. The bushings are normally delivered from ABB in boxes with the bushing supported by blocks and fiber boards. The boxed are marked with Top end. This information can be important and shows how the bushing is oriented inside the box. Care must be taken when storing the bushings so that the silicone rubber sheds are not damaged. For instance, rodents, insects or birds can destroy the sheds. The largest bushings are delivered with shipping supports to secure the conductor during transport and storage. The supports must be removed, see the installation and maintenance for each GGFL type for further instructions. Long term storage Bushings for long term storage (>1 year) should be kept indoors with controlled temperature and low humidity. Table 1. General specifications Application: Classification: Ambient temperature: Altitude of site: Type of insulating media: Markings: Wall bushing SF 6 gas insulated bushing +60 C to -30 C, for use in valve halls or equivalent environments, other temperatures can be evaluated on request. < 1000 m. Bushings for other altitudes can be provided on request. SF 6 gas at 5.7 bar absolute pressure at 20 C Conforming to IEC/IEEE

9 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE 9 Testing 06 Test tap. All manufactured parts are individually pressure tested during manufacturing. Pressure testing of each individual bushing is carried out at 900 kpa (9 bar) overpressure and tightness test is carried out at 600 kpa (6 bar) overpressure according to IEC and IEC/IEEE The bushing is protected from overpressures by a bursting disc installed on the intermediate flange or at the end cover depending on the design. 06 Standards The GGFL bushing is designed and tested according to IEC 60137, IEC/IEEE , and IEEE C For applications that call for different specifications, please contact ABB. Routine testing The bushing is routine tested according to applicable standards IEC 60137, IEEE C and IEC/IEEE for DC applications. The tests include measurement of partial discharge quantity, tan δ, capacitance, dry power frequency withstand, and if applicable DC voltage withstand, polarity reversal test and insulation of test tap. Visual inspection and tightness/ pressure tests of gas insulated bushings are performed and an individual routine test report is issued with each bushing. Type tests Complete type tests have been performed and reports are available on request. Test tap The GGFL bushings provided with capacitive test taps have designs that comply with the standard ANSI/IEEE C Type A Normally grounded tap. The test tap is positioned on the intermediate flange. For bushings without measuring tap, the capacitance of the bushing may be measured between the wall flange and the high voltage end.

10 10 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE Dimensions and data The design of the GGFL type wall bushing is highly flexible, and parameters can be selected within a wide range. Tables 2 and 3 are given as examples of applications previously installed. Table 2. Mechanical data and dimensions. Cantilever test load Nx1 min Total length (m) Creepage distance (mm) A-side/B-side Bushing Catalog number Dimension drawing Mass with SF 6 gas (kg) Test tap Bellow GGFL 450 1ZSC AAA 1ZSC AAA /3600 No No GGFL 450 1ZSC AAB 1ZSC AAB /3600 No No GGFL 450 1ZSC AAC 1ZSC AAC /3600 No No GGFL 530 1ZSC AAA 1ZSC AAA /5215 No No GGFL 378 1ZSC AAB 1ZSC AAB /5215 No No GGFL 325 1ZSC AAC 1ZSC AAC /3445 No No GGFL 530 1ZSC AAD 1ZSC AAD /5215 No No GGFL 650 1ZSC AAE 1ZSC AAE /5746 No No GGFL 650 1ZSC AAF 1ZSC AAF /5746 No No GGFL 550 1ZSC AAG 1ZSC AAG /5215 No No GGFL 857 1ZSC AAA 1ZSC AAA /10348 Yes No GGFL 787 1ZSC AAB 1ZSC AAB /7516 Yes No GGFL 782 1ZSC AAC 1ZSC AAC /7516 No No GGFL 1050/420/3150 1ZSC AAA 1ZSC AAA /10650 No No GGFL 1050/420/3150 LC 1ZSC AAB 1ZSC AAB /13250 No No GGFL 1460 LF E /14400 Yes Yes GGFL 1300 LF L /5850 Yes Yes GGFL 1425 LF P /15900 Yes Yes GGFL 1425 LF R /15900 Yes Yes GGFL 400 1ZSC AAA 1ZSC AAA /13500 No Yes GGFL 600 1ZSC AAA 1ZSC AAA /17100 No Yes GGFL 800 1ZSC AAA 1ZSC AAB /11430 No Yes GGFL 150HC 1ZSC AAF 1ZSC AAF /7200 No No GGFL 400HC 1ZSC AAB 1ZSC AAB /13000 No Yes GGFL 800HCL 1ZSC AAB 1ZSC AAB /23200 No Yes GGFL 550 1ZSC AAE 1ZSC AAE /17100 No Yes GGFL ZSC AAA 1ZSC AAA /32500 No Yes

11 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE 11 Electrical data Typical rated order specific values for installed bushings are shown in the table below. These ratings are in many cases not the limit for each specific bushing and other combinations may be provided. Dielectric losses Due to the low dielectric loss of SF 6, in theory close to zero loss for ideal pure gas, the bushing has an extremely low dissipation factor (tan δ). For DC voltages this is of less concern, but for alternating voltages the bushing displays extremely low dielectric losses. This feature of the GGFL bushing has given an application in the ABB HVDC Light projects, connecting the phase reactor to the HVDC valve. Due to the switching of bipolar transistors in HVDC Light, a large amount of harmonics at high frequency are produced. Any other types of bushing with solid or liquid insulation easily overheat in this position, due to dielectric loss. The GGFL can handle these harmonics due to both the low capacitance as well as the inherent low loss properties of the gas. Table 3. Electrical data. Bushing Catalog number Rated voltage (kv DC/kV AC) Rated current (A DC/A AC) GGFL 450 1ZSC AAA 175/ GGFL 450 1ZSC AAB 175/ GGFL 450 1ZSC AAC 175/ Lightning impulse (kv) Switching impulse Dry/wet (kv) 200/ tested 200/ tested 200/ tested 2h DC (kv) tested tested tested GGFL 530 1ZSC AAA 210/ / / GGFL 378 1ZSC AAB 210/ tested / GGFL 325 1ZSC AAC 210/ tested 219 Polarity reversal (kv) Dry power frequency (kv) Capacitance C/C 1 /C 2 (pf) tested /N.A/N.A tested /N.A/N.A tested /N.A/N.A tested /N.A/N.A tested /N.A/N.A tested /N.A/N.A GGFL 530 1ZSC AAD 210/ / tested /N.A/N.A GGFL 650 1ZSC AAE 210/ / tested /N.A/N.A GGFL 650 1ZSC AAF 210/ / (Wet) 100/N.A/N.A GGFL 550 1ZSC AAG 210/ / (Wet) 145/N.A/N.A GGFL 857 1ZSC AAA 320/ GGFL 787 1ZSC AAB 320/ GGFL 782 1ZSC AAC 320/ GGFL 1050/420/3150 1ZSC AAA 320/ / tested 552 tested /80/ / tested /70/ / tested 450 tested /N.A/N.A 950/ tested /N.A/N.A GGFL 1050/420/3150 LC 1ZSC AAB 320/ / /N.A/N.A GGFL 1460 LF E 515/ / /140/230 GGFL 1300 LF L 500/ / /155/230 GGFL 1425 LF P 515/ / /155/230 GGFL 1425 LF R 500/ / /155/390 GGFL 400 1ZSC AAA 400/ / /N.A/N.A GGFL 600 1ZSC AAA 600/ / /N.A/N.A GGFL 800 1ZSC AAA 800/ / /N.A/N.A GGFL 150HC 1ZSC AAF 150/ / /172/N.A GGFL 400HC 1ZSC AAB 400/ / N.A/209.7/N.A GGFL 800HCL 1ZSC AAB 800/ / N.A/341/N.A GGFL 550 1ZSC AAE 550/ / N.A/206/N.A GGFL ZSC AAA 1100/ / N.A/371/N.A

12 12 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE Connection details 07 Terminal GGFL 400, 600 and Terminal GGFL Terminal stud cover. Outer terminal The outer terminal is available in any design requested. Typically, an aluminum terminal stud with stud length 140 mm and diameter 60 mm is specified for currents up to and including 2500 A. Current demands over 2500 A have a terminal switch stud length of 140 mm and diameter of 80/130mm, made of copper. The outer terminal contact force is achieved with six M10 screws. The contact area is protected by an O-ring gasket assembly. Terminal Torque 40 Nm Conical spring washer Large washer O-ring The outer terminals for GGFL 150HC, 400HC, 800HCL, 550 and 1100 are equipped with built-in stud covers. The covers are screwed and sealed with O-rings to the end covers of the bushings. 07 The contact surfaces of the terminal studs are silver coated, and withstand currents over 2500 A. Terminal Torque 40 Nm Washer O-ring 08 Terminal Torque 40 Nm Conical spring washer Large washer O-ring 09

13 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE 13 End-shields End-shields are necessary for corona-free operation at voltages exceeding approximately 200 kv DC or 170 kv AC rms phase-to-ground (300 kv system). The end shields are attached to existing screws at both ends of the bushing. For retrofitting, the bushing can be made to fit existing building and yard hardware. Table 4. End shields. Bushing Dimension drawing Corona shield outdoor Corona shield indoor GGFL 450 1ZSC AAA No corona shields are needed No corona shields are needed GGFL 450 1ZSC AAB No corona shields are needed No corona shields are needed GGFL 450 1ZSC AAC No corona shields are needed No corona shields are needed GGFL 530 1ZSC AAA 1ZSC AAB 1ZSC AAB GGFL 378 1ZSC AAB 1ZSC AAB 1ZSC AAB GGFL 325 1ZSC AAC 1ZSC AAB 1ZSC AAB GGFL 530 1ZSC AAD 1ZSC AAB 1ZSC AAB GGFL 650 1ZSC AAE 1ZSC AAB 1ZSC AAB GGFL 650 1ZSC AAF 1ZSC AAB 1ZSC AAB GGFL 550 1ZSC AAG 1ZSC AAB 1ZSC AAB GGFL 857 1ZSC AAA 1ZSC AAA 1ZSC AAA GGFL 787 1ZSC AAB 1ZSC AAA 1ZSC AAA GGFL 782 1ZSC AAC 1ZSC AAA 1ZSC AAA GGFL 1050/420/3150 1ZSC AAA 1ZSC AAR 1ZSC AAR GGFL 1050/420/3150 LC 1ZSC AAB 1ZSC AAR 1ZSC AAR GGFL ZSC AAM Required, usually provided by customer. Coordinated with bus-work. GGFL ZSC AAM Required, usually provided by customer. Coordinated with bus-work. GGFL ZSC AAM Required, usually provided by customer. Coordinated with bus-work GGFL ZSC AAM Required, usually provided by customer. Coordinated with bus-work. GGFL 400 1ZSC AAA 1ZSC AAG 1ZSC AAH GGFL 600 1ZSC AAA 1ZSC AAK 1ZSC AAK GGFL 800 1ZSC AAB 1ZSC AAJ 1ZSC AAB GGFL 150HC 1ZSC AAF 1ZSC AAE 1ZSC AAE GGFL 400HC 1ZSC AAB 1ZSC ABC 1ZSC ABC GGFL 800HCL 1ZSC AAB 1ZSC ABE 1ZSC ABE GGFL 550 1ZSC AAE 1ZSC AAJ 1ZSC AAB GGFL ZSC AAA 1ZSC AAW 1ZSC AAV

14 14 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE Insulation gas The main insulation consists of pure compressed SF 6 gas (sulfur hexafluoride). A N 2 + SF 6 mixture is used in extremely cold climates (below -30 C). The two purposes of the compressed gas are to cool the tubular conductor and to provide insulation from ground. Its capacity for doing so depends on the density of the gas. The bushing is normally filled with gas at a pressure of 570 kpa (5.7 bar) absolute at 20 C. The filling is made through a gas connection valve on the intermediate flange. This valve can be connected through tubing to ground level to enable emergency topping up during service. Shipping The bushing is shipped at a slight overpressure of 0.25 bar, with nitrogen gas. After installation and prior to operation a vacuum must be drawn so that air and humidity are removed and after that SF 6 gas is added to the operating pressure (570 kpa abs. at 20 C). The pressure gauge, if used, is intended to give a locally visible check of the internal pressure of the bushing, roughly indicating whether the bushing has the correct gas density or not. The SF 6 gas density monitor may be set to give signals at a number of different levels, either for warning or to trip at low gas density. The quality of the SF 6 gas should comply with standards IEC and 60796b Specifications and acceptance of new sulfur hexafluoride. Gas and gas handling equipment are not included in the delivery from ABB. We refer to suppliers like Dilo and Svenska Transforfilter AB (Malmqvist) for purchase of gas handling equipment and gas.

15 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE 15 Gas monitoring 10 Density guard. Since the late 1990 s, each gas insulated bushing for HVDC projects has been supplied with two independent three-stage density switches. The devices are sometimes called density monitors, pressure monitors etc., but should more correctly be labeled density switches. The function is to activate one of three independent switching contacts, each one for a different density level of the insulating gas. The first is activated at a pressure of 530 kpa (5.3 bar) abs. at 20 C to indicate low gas density. The devices only activate the internal switches, and it is up to the user to connect and interpret the position of the switches in their alarm and monitoring system. Furthermore, alarm settings, trip settings etc. are often requested, but the devices themselves do not differentiate between alarms and trips, it is up to the user to decode, and perhaps at the third level, corresponding to the lowest density-pressure setting, the user may wish to trip or block the energized equipment for investigation. The second signal level is activated at 520 kpa (5.2 bar) abs. at 20 C to indicate very low gas density. Once again, sometimes the three levels are referred to as alarm level 1 and alarm level 2 and the third level considered a trip level. The third level gives an alarm at 500 kpa (5 bar) abs. at 20 C, which is the dimensioning density of the bushing. At gas densities below 500 kpa the type test levels for dielectric strength do not apply. The ability of the bushing to conduct current declines progressively with falling gas density. It is important to remember that each of the three contacts is merely switching at each respective level, and whether each step is regarded as alarm or trip is defined by the user and should be adapted by the owner to the local procedures at each station. The units do not provide an active signal, and referring to items such as alarm or trip signals from the density monitor may lead to erroneous conclusions. 10

16 16 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE 11 Circuit diagram example. The user is to connect a voltage control signal to a connection block for each switching step. The interpretation of the switch position is then made by checking which of the contacts is carrying the voltage, indicating if the gas density is above or below the pre-set level of engagement for switch action. The recommendation from ABB is to not operate the bushings at levels below the third stage, since the bushings are type and routine tested with a level three condition of the insulating gas. This implies the insulating characteristics of the bushings are guaranteed down to the lowest level of the density switch. The third stage may thus in practice be regarded as a trip level but this is decided and programmed into the user's alarm system. This is the background to the devices being labeled as density switches, but for simplicity the pressure of the gas at a temperature of 20 C is commonly used. This can be seen in the descriptions below where a pressure level is related to a temperature. If dealing with density only, the temperature reference could be removed. Thus, the nominal filling condition the density giving a pressure of 570 kpa absolute at 20 C is the correct interpretation. The same density gives a higher pressure at higher temperatures, and a lower at lower temperatures. All references to pressure in the following description are referred to at 20 C. When dealing with gas insulation it is preferred to deal with the concept of density. The insulating properties of SF6 are dependent on the density, the number of molecules in the enclosed space, and not directly the pressure, which could be compared to how active the molecules are. Switch number D3 D2 D1 P/T = nominal Ground Terminal block number

17 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE 17 Mechanical loading The cantilever operational and test loads are given in Table 5. The force is applied at the center of the outer terminal of the bushing. For extraordinary requirements which include earthquakes, extreme environmental conditions and heavy equipment, consult the supplier. The tests are performed in accordance with IEC and IEEE C Seismic tests The GGFL1300 designed for severe seismic requirements for southern California has been verified by a full-scale shake table test. This test is used as a reference for similar bushings. Table 5. Mechanical loading. Bushing Dimension drawing Max. cantilever operating load Max. cantilever test load GGFL 450 1ZSC AAA GGFL 450 1ZSC AAB GGFL 450 1ZSC AAC GGFL 530 1ZSC AAA GGFL 378 1ZSC AAB GGFL 325 1ZSC AAC GGFL 530 1ZSC AAD GGFL 650 1ZSC AAE GGFL 650 1ZSC AAF GGFL 550 1ZSC AAG GGFL 857 1ZSC AAA GGFL 787 1ZSC AAB GGFL 782 1ZSC AAC GGFL 1050/420/3150 1ZSC AAA GGFL 1050/420/3150 LC 1ZSC AAB GGFL GGFL GGFL GGFL GGFL 400 1ZSC AAA GGFL 600 1ZSC AAA GGFL 800 1ZSC AAB GGFL 150HC 1ZSC AAF GGFL 400HC 1ZSC AAB GGFL 800HCL 1ZSC AAB GGFL 550 1ZSC AAE GGFL ZSC AAA

18 18 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE Short-time current The rated thermal short-time current (Ith) is calculated according to IEC The rated dynamic current (Id) is 2.5 times the 1 second short-time current. Table 6. Short-time current. Bushing Dimension drawing Rated current Short-time current I th ka, rms, 1s Dynamic current Id ka, peak GGFL 450 1ZSC AAA GGFL 450 1ZSC AAB GGFL 450 1ZSC AAC GGFL 530 1ZSC AAA GGFL 378 1ZSC AAB GGFL 325 1ZSC AAC GGFL 530 1ZSC AAD GGFL 650 1ZSC AAE GGFL 650 1ZSC AAF GGFL 550 1ZSC AAG GGFL 857 1ZSC AAA GGFL 787 1ZSC AAB GGFL 782 1ZSC AAC GGFL 1050/420/3150 1ZSC AAA GGFL 1050/420/3150 LC 1ZSC AAB GGFL GGFL GGFL GGFL GGFL 400 1ZSC AAA GGFL 600 1ZSC AAA GGFL 800 1ZSC AAB GGFL 150HC 1ZSC AAF GGFL 400HC 1ZSC AAB GGFL 800HCL 1ZSC AAB GGFL 550 1ZSC AAE GGFL ZSC AAA

19 GAS INSULATED WALL BUSHINGS TYPE GGFL TECHNICAL GUIDE 19 Ordering particulars When ordering, please state: Type and catalog number for bushing. Catalog number for outer terminal. Additional accessories or modifications. Test required, in addition to the normal routine tests. Ordering example: Bushing: GGFL1050/420/3150 1ZSC AAA Outer terminal: Cu/Ag, D = 80 mm 1ZSC AAC

20 ABB AB, Components SE Ludvika Sweden Copyright 2017 ABB. All rights reserved. Specifications subject to change without notice. 1ZSC ABJ en, Rev. 1,

1ZSE EN, REV. 4. Wall bushings type GSA-AA Technical guide

1ZSE EN, REV. 4. Wall bushings type GSA-AA Technical guide 1ZSE 2750-112 EN, REV. 4 Wall bushings type GSA-AA Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

1ZSC AAA EN, REV. 7. Transformer bushings type GSBK Technical guide

1ZSC AAA EN, REV. 7. Transformer bushings type GSBK Technical guide 1ZSC563-AAA EN, REV. 7 Transformer bushings type GSBK Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

Resin Impregnated Paper Bushing, Oil to Air, Type GSB Technical guide

Resin Impregnated Paper Bushing, Oil to Air, Type GSB Technical guide 1ZSC000563-AAC en, Rev. 2 Resin Impregnated Paper Bushing, Oil to Air, Type GSB Technical guide This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers,

More information

1ZSE EN, REV. 7. Oil SF 6. bushings type GOEK Technical guide

1ZSE EN, REV. 7. Oil SF 6. bushings type GOEK Technical guide 1ZSE 2750-106 EN, REV. 7 Oil SF 6 bushings type GOEK Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

1ZSC AAA en, Rev. 6. Resin impregnated paper bushing, oil to SF 6., type GSBK Technical guide

1ZSC AAA en, Rev. 6. Resin impregnated paper bushing, oil to SF 6., type GSBK Technical guide 1ZSC563-AAA en, Rev. 6 Resin impregnated paper bushing, oil to SF 6, type GSBK Technical guide Original instruction The information provided in this document is intended to be general and does not cover

More information

Transformer bushings, type GOH. Technical guide

Transformer bushings, type GOH. Technical guide Transformer bushings, type GOH Technical guide This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers, access to all the technical information required

More information

Resin Impregnated Paper Bushing, Oil to SF 6. , Type GSBK

Resin Impregnated Paper Bushing, Oil to SF 6. , Type GSBK 1ZSC563-AAA en, Rev. 2 Resin Impregnated Paper Bushing, Oil to SF 6, Type GSBK Technical guide This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers,

More information

1ZSE en, Rev. 3. Wall bushings, type GSA-AA Technical guide

1ZSE en, Rev. 3. Wall bushings, type GSA-AA Technical guide 1ZSE 2750-112 en, Rev. 3 Wall bushings, type GSA-AA Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

Bushings for High Voltage AC Applications

Bushings for High Voltage AC Applications Bushings for High Voltage AC Applications Selection guide 1ZSE 2750-100 en, Rev. 3, 2006-03-15 During selection of for high voltage applications several important factors have to be considered to ensure

More information

1ZSE en, Rev. 7. Transformer bushings, type GOB Technical guide

1ZSE en, Rev. 7. Transformer bushings, type GOB Technical guide 1ZSE 2750-102 en, Rev. 7 Transformer bushings, type GOB Technical guide This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers, access to all the technical

More information

1ZSE en, Rev. 9. Transformer bushings, type GOB Technical guide

1ZSE en, Rev. 9. Transformer bushings, type GOB Technical guide 1ZSE 2750-102 en, Rev. 9 Transformer bushings, type GOB Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

Transformer bushings, type GOA 250. Installation and maintenance guide

Transformer bushings, type GOA 250. Installation and maintenance guide Transformer bushings, type GOA 250 Installation and maintenance guide This document must not be copied without our written permission, and the contents thereof must not be imparted to a third party nor

More information

1ZSE en, Rev. 9. Transformer bushings, type GSA-OA Technical guide

1ZSE en, Rev. 9. Transformer bushings, type GSA-OA Technical guide 1ZSE 2750-111 en, Rev. 9 Transformer bushings, type GSA-OA Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

Micafil transformer oil-sf 6 bushings GARIP / RTKG kv. Power and productivity for a better world TM ABB

Micafil transformer oil-sf 6 bushings GARIP / RTKG kv. Power and productivity for a better world TM ABB Micafil transformer oil-sf 6 bushings GARIP / RTKG 72.5 55 kv Power and productivity for a better world TM ABB Design and accessories The design of the main RIP insulating body includes a solid, non-removable

More information

Product presentation CPT tech Jason Evershed, ABB Transformer Components, May 21st New RIS transformer bushings The paper-free solution

Product presentation CPT tech Jason Evershed, ABB Transformer Components, May 21st New RIS transformer bushings The paper-free solution Product presentation CPT tech Jason Evershed, ABB Transformer Components, May 21st 2014 New RIS transformer bushings The paper-free solution Transformer condenser bushings Why a new technology? To preserve

More information

Outdoor live tank SF6 circuit breaker EDT with integrated current transformer up to 72.5 kv

Outdoor live tank SF6 circuit breaker EDT with integrated current transformer up to 72.5 kv Outdoor live tank SF6 circuit breaker EDT with integrated current transformer up to 72.5 kv SF6 circuit breaker EDT with integrated current transformer ABB is a world leader in live tank circuit breaker

More information

Surge arrester POLIM-H..SD

Surge arrester POLIM-H..SD Data sheet Surge arrester POLIM-H..SD Technical data Classification according to EN 50526-1 and IEC 62848-1 Nominal discharge current I n (8/20 µs) 10 ka peak Class DC-B High current impulse I hc (4/10

More information

1ZSC ABE en, Rev. 1. HVDC bushing, type GSD Installation and maintenance guide

1ZSC ABE en, Rev. 1. HVDC bushing, type GSD Installation and maintenance guide 1ZSC000563-ABE en, Rev. 1 HVDC bushing, type GSD Installation and maintenance guide Original instruction The information provided in this document is intended to be general and does not cover all possible

More information

Surge arrester POLIM-C.. HD

Surge arrester POLIM-C.. HD DATA SHEET Surge arrester POLIM-C.. HD Technical data Classification according to EN 50526-1 and IEC 62848-1 Nominal discharge current I n (8/20 µs) 10 ka peak Class DC-A High current impulse I hc (4/10

More information

Surge arrester POLIM-H.. ND

Surge arrester POLIM-H.. ND DATA SHEET Surge arrester POLIM-H.. ND Technical data Classification according to EN 50526-1 and IEC 62848-1 Nominal discharge current I n (8/20 µs) 10 ka peak Class DC-B High current impulse I hc (4/10

More information

dfdf 34.5 kv and 69 kv, Type O Plus C II Condenser Bushings Technical Guide

dfdf 34.5 kv and 69 kv, Type O Plus C II Condenser Bushings Technical Guide dfdf 34.5 kv and 69 kv, Type O Plus C II Condenser Bushings Technical Guide Table of contents 1 Introduction... 3 1.1 Style Number... 3 1.1.1 Style Number Examples... 3 2 Basic Characteristics... 4 2.1

More information

Transformer bushings, type GSA-OA Technical guide

Transformer bushings, type GSA-OA Technical guide Transformer bushings, type GSA-OA Technical guide ZSE 2750- en, Rev. 5, 2005-05-5 This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers, access to

More information

PABS. AIR-TO-SF 6 - Gas-insulated bushing IEC STANDARDS ANSI STANDARDS AN ALSTOM COMPANY

PABS. AIR-TO-SF 6 - Gas-insulated bushing IEC STANDARDS ANSI STANDARDS AN ALSTOM COMPANY PABS Air-to-SF 6 Bushings 7.5-800 kv BUSHINGS AIR-TO-SF 6 - Gas-insulated bushing IEC STANDARDS 7 - ANSI STANDARDS AN ALSTOM COMPANY PABS bushings are gas-insulated types that meet IEC 7, ANSI/IEEE or

More information

MICAFIL RIP Transformer Bushings AirRIP / RTKF kv

MICAFIL RIP Transformer Bushings AirRIP / RTKF kv INSULATION AND COMPONENTS MICAFIL RIP Transformer Bushings AirRIP / RTKF kv MICAFIL AirRIP bushings offer an extended service life combined with enhanced reliability and safety to ensure the maximum availability

More information

Voltage limiting device HVL

Voltage limiting device HVL Datasheet Voltage limiting device HVL 120-0.3 1 2 3 3 Equivalent circuit of voltage limiting device Type HVL 120-0.3 1 MO-surge arrester 2 Trigger electronics 3 Thyristor Product Description The HVL 120-0.3

More information

Voltage limiting device HVL

Voltage limiting device HVL Datasheet Voltage limiting device HVL 60-0.3 1 2 3 3 Equivalent circuit of voltage limiting device Type HVL 60-0.3 1 MO-surge arrester 2 Trigger electronics 3 Thyristor Product Description The HVL 60-0.3

More information

Current transformers. Outdoor operation SF 6 -gas insulated. JGF ( ) kv

Current transformers. Outdoor operation SF 6 -gas insulated. JGF ( ) kv Current transformers Outdoor operation SF 6 -gas insulated JGF (245 550) kv General description Current transformers type JGF are used in high voltage switchgear within the 245 550 kv range. They transform

More information

HVDC bushing without oil side porcelain Type GOF, for outdoor mounting. Installation and maintenance guide

HVDC bushing without oil side porcelain Type GOF, for outdoor mounting. Installation and maintenance guide HVDC bushing without oil side porcelain Type GOF, for outdoor mounting Installation and maintenance guide This document must not be copied without our written permission, and the contents thereof must

More information

ACCESSORIES FOR LPOF, HPPT AND XLPE HIGH VOLTAGE CABLE SYSTEMS PRODUCT CATALOGUE

ACCESSORIES FOR LPOF, HPPT AND XLPE HIGH VOLTAGE CABLE SYSTEMS PRODUCT CATALOGUE ACCESSORIES FOR LPOF, HPPT AND XLPE HIGH VOLTAGE CABLE SYSTEMS PRODUCT CATALOGUE hvgrid-tech designs and manufactures high voltage cable accessories for all types of cable systems, ranging from 69 kv to

More information

ZX2 Gas-insulated medium voltage switchgear

ZX2 Gas-insulated medium voltage switchgear Gas-insulated medium voltage switchgear Double busbar 13 8 10 12 11 10 9 8 7 2 1 3 4 5 6 2 Versatile Partitioned single or double busbar system for all applications even with the most demanding parameters

More information

Dead Tank Circuit Breaker 145PM40-C Compact design with enhanced reliability

Dead Tank Circuit Breaker 145PM40-C Compact design with enhanced reliability Dead Tank Circuit Breaker 145PM40-C Compact design with enhanced reliability ABB innovations for changing demands ABB (www.abb.com) is a leader in power and automation technologies that enables utility

More information

Transformer High Current Bushings Type CFPT & CFCT 36kV up to 40kA IEC

Transformer High Current Bushings Type CFPT & CFCT 36kV up to 40kA IEC Transformer High Current Bushings Type CFPT & CFCT 36kV up to 40kA IEC 60137-2008 High current bushings for transformer Features Bushing Type CFPT version Porcelain Insulator Trench RIG technology for

More information

en, Rev. 10. Transformer bushings, type GOH Installation and maintenance guide

en, Rev. 10. Transformer bushings, type GOH Installation and maintenance guide 2750 515-85 en, Rev. 10 Transformer bushings, type GOH Installation and maintenance guide Original instruction The information provided in this document is intended to be general and does not cover all

More information

Low voltage bushings for pad-mounted distribution transformers Technical information guide

Low voltage bushings for pad-mounted distribution transformers Technical information guide Transformer components Low voltage bushings for pad-mounted distribution transformers Technical information guide ABB low voltage bushings terminate a transformer s internal low voltage leads at the tank

More information

en, Transformer bushing, type GSA-OA Installation and maintenance guide...

en, Transformer bushing, type GSA-OA Installation and maintenance guide... Transformer bushing, type GSA-OA Installation and maintenance guide... The information contained in this document may be subject to change without prior warning and should not be considered as binding

More information

en, Rev. 7. Transformer bushings, type GOM Installation and maintenance guide

en, Rev. 7. Transformer bushings, type GOM Installation and maintenance guide 2750 515-41 en, Rev. 7 Transformer bushings, type GOM Installation and maintenance guide Original instruction The information provided in this document is intended to be general and does not cover all

More information

DM Condenser bushings, kV DURESCA

DM Condenser bushings, kV DURESCA DM Condenser bushings, 36 DURESCA Through wall bushings for indoor and outdoor applications, Resin Impregnated Paper IEC 601378 and IEEE C57.19.01.004 DURESCA Wall bushings Swiss quality combined with

More information

OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) kV to 550kV up to 5000A IEC

OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) kV to 550kV up to 5000A IEC OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) 1800 24kV to 550kV up to 5000A IEC 60137-2008 Features If you need any transformer bushing proven in operation conditions around the world, Trench

More information

MEDIUM VOLTAGE PRODUCTS. Fault Current Limiters I S. -limiter and FC-Protector The worldʼs fastest switching devices

MEDIUM VOLTAGE PRODUCTS. Fault Current Limiters I S. -limiter and FC-Protector The worldʼs fastest switching devices MEDIUM VOLTAGE PRODUCTS The worldʼs fastest switching devices 2 FAULT CURRENT LIMITERS THE WORLDʼ S FASTETST SWITCHING DEVICES The worldʼs fastest switching devices ABBʼs fault current limiters disconnect

More information

EMPAC Metal enclosed capacitor bank for wind applications

EMPAC Metal enclosed capacitor bank for wind applications EMPAC Metal enclosed capacitor bank for wind applications Introduction The EMPAC is a Metal Enclosed Capacitor Bank suitable for voltages between 1 kv and 36 kv for reactive compensation in MV networks

More information

Fuse-links type CEF-VT Rated voltages 3/7.2 kv - 10/24 kv Rated current 0.5 A 6.3 A

Fuse-links type CEF-VT Rated voltages 3/7.2 kv - 10/24 kv Rated current 0.5 A 6.3 A DISTRIBUTION SOLUTIONS Fuse-links type CEF-VT Rated voltages 3/7.2 kv - 10/24 kv Rated current 0.5 A 6.3 A Efficient protection of voltage transformer circuits Extending the lifetime of installed electrical

More information

INSTRUCTION MANUAL CRS Combined insulation bushing

INSTRUCTION MANUAL CRS Combined insulation bushing INSTRUCTION MANUAL CRS Combined insulation bushing 5COH020200 CRS REV03 2 TABLE OF CONTENTS 1 SAFETY... 5 1.1 SAFETY INSTRUCTION... 5 1.2 SPECIFIED APPLICATION... 5 1.3 SAFETY NOTES ON THE EQUIPMENT OPERATION...

More information

ZX-Family Gas-insulated medium voltage switchgear

ZX-Family Gas-insulated medium voltage switchgear ZX-Family Gas-insulated medium voltage switchgear Minimum overall costs ZX offers maximum economy The compact design of the panels reduces the space required and therefore the size of the station. Freedom

More information

Product Brochure. Generator Circuit-Breaker HVR-EBCB For hydro or pump storage power plant

Product Brochure. Generator Circuit-Breaker HVR-EBCB For hydro or pump storage power plant Product Brochure Generator Circuit-Breaker HVR-EBCB For hydro or pump storage power plant Introduction General The braking switch serves the purpose of electrical braking a machine in a hydro or pumped

More information

Bus bar Bushings up to 1.1kV and from 1.6kA to 4kA for Liquid Filled Transformers:

Bus bar Bushings up to 1.1kV and from 1.6kA to 4kA for Liquid Filled Transformers: 4 (Four) Pole Monoblock: Bus bar Bushings up to 1.1kV and from 1.6kA to 4kA for Liquid Filled Transformers: Designed and manufactured in accordance with EN 50336:2002 and BS 2562: 1979 1 Introduction:

More information

Technical Specification For Outdoor Substation Harmonic Filter Banks

Technical Specification For Outdoor Substation Harmonic Filter Banks Technical Specification For Outdoor Substation Harmonic Filter Banks One of Three 5th, 11th & 23rd, 34.5 kv, Rated Harmonic Filter Assemblies Provided for a Central Venezuela Heavy Oil Production Field

More information

43-SDMS-04 REV. 00 SPECIFICATIONS FOR

43-SDMS-04 REV. 00 SPECIFICATIONS FOR 43-SDMS-04 REV. 00 SPECIFICATIONS FOR SHUNT CAPACITOR BANK 13.8 kv THROUGH 69 kv FOR PRIMARY DISTRIBUTION SUBSTATIONS This specification is property of SEC and subject to change or modification without

More information

Low voltage capacitors CLMD Improving power factor and enhancing power quality of your network

Low voltage capacitors CLMD Improving power factor and enhancing power quality of your network PRODUCT BROCHURE Low voltage capacitors CLMD Improving power factor and enhancing power quality of your network s.a. ABB n.v. Power Quality Products Allée Centrale 10 Z.I. Jumet B-6040 Charleroi (Jumet)

More information

Surge arrester POLIM-H..N

Surge arrester POLIM-H..N Data sheet Surge arrester POLIMH..N Technical data Arrester class SH, Station High Line discharge class (LD) 4 Nominal discharge current I n (8/20 µs) 20 ka peak Repetitive charge transfer rating Q rs

More information

Combined instrument transformers

Combined instrument transformers Combined instrument transformers Outdoor operation SF 6 -gas insulated EJGF (245 550) kv General description Type EJGF combined transformers are used in high-voltage substations within the 245 550 kv range.

More information

MEDIUM VOLTAGE PRODUCT. TJC 4 Indoor voltage transformers

MEDIUM VOLTAGE PRODUCT. TJC 4 Indoor voltage transformers MEDIUM VOLTAGE PRODUCT TJC 4 Indoor voltage transformers 2 TJC 4 INDOOR VOLTAGE TRANSFORMERS Parameters Highest voltage for equipment Power frequency test voltage, 1 min. Lightning impulse test voltage

More information

OTCF. Grid Solutions. Capacitor Voltage Transformers 72.5 kv to 800 kv. Quality Product Design. Seismic Withstand Capability.

OTCF. Grid Solutions. Capacitor Voltage Transformers 72.5 kv to 800 kv. Quality Product Design. Seismic Withstand Capability. GE Grid Solutions OTCF Capacitor Voltage Transformers 72.5 kv to 800 kv In high and extra high voltage transmission systems, capacitor voltage transformers (CVTs) are used to provide potential outputs

More information

A manufacturer s view of bushing reliability, testing and analysis. Lars Jonsson Håkan Rudegard

A manufacturer s view of bushing reliability, testing and analysis. Lars Jonsson Håkan Rudegard A manufacturer s view of bushing reliability, testing and analysis By Lars Jonsson Håkan Rudegard 1 A manufacturer s view of bushing reliability, testing and analysis Lars Jonsson Håkan Rudegard ABB Sweden

More information

35-kV Thru-Bushings F Series (bolt-in) for Air-Insulated to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp

35-kV Thru-Bushings F Series (bolt-in) for Air-Insulated to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp Page 1 2018 Equipment Connection Bus Bar, or Grounded Metal Equipment Plate F Series Mounting Holes ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric

More information

Brochure. Modular Systems wind portfolio Power Collection and Grid Connection products

Brochure. Modular Systems wind portfolio Power Collection and Grid Connection products Brochure Modular Systems wind portfolio Power Collection and Grid Connection products Wind portfolio Background ABB is one of the few suppliers that has been deeply involved in wind power segment development,

More information

1ZSC AAX EN, Transformer bushing, type GSC Installation and maintenance guide

1ZSC AAX EN, Transformer bushing, type GSC Installation and maintenance guide 1ZSC000563-AAX EN, 2018-01-16 Transformer bushing, type GSC Installation and maintenance guide The information contained in this document may be subject to change without prior warning and should not be

More information

Type HS PEXLIM-P Surge Arresters Maximum System Voltage 123 kv to 800 kv

Type HS PEXLIM-P Surge Arresters Maximum System Voltage 123 kv to 800 kv Type HS PEXLIM-P Surge Arresters Maximum System Voltage 123 kv to 800 kv HS PEXLIM-P Metal Oxide Surge Arrester HS PEXLIM-P Surge Arresters are used for the protection of switchgear, transformers and other

More information

Electronic overload relay EF65, EF96 and EF146

Electronic overload relay EF65, EF96 and EF146 Data sheet Electronic overload relay EF65, EF96 and EF146 Electronic overload relays are the alternative to the thermal overload relays. An electronic overload relay offers reliable and fast protection

More information

Inductive voltage transformers

Inductive voltage transformers Inductive voltage transformers Outdoor operation SF 6 -gas insulated EGF (245 550) kv General description Voltage transformers type EGF are used in high voltage substations within the 245 550 kv range.

More information

25-kV Apparatus Bushings A Series (clamp-in) for Elbow to Air-Insulated Service 200 Amp and 600 Amp

25-kV Apparatus Bushings A Series (clamp-in) for Elbow to Air-Insulated Service 200 Amp and 600 Amp Page 1 2018 Grounded Metal Equipment Plate Equipment Connection 15 kv or 25 kv Separable Insulated Connector (elbow) Grounded Metal Equipment Plate Equipment Connection Power Cable Power Cable ELRIM Cycloaliphatic

More information

B kv T&D GAS INSULATED SWITCHGEAR

B kv T&D GAS INSULATED SWITCHGEAR GAS INSULATED SWITCHGEAR B 105 170 300 kv The increasing demand for electrical power in cities and industrial centers necessitates the installation of a compact and efficient distribution and transmission

More information

25 kv Apparatus Bushings

25 kv Apparatus Bushings Page 1 2001 ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric strength, dielectric loss and power factor Choice of shapes allows design innovation

More information

Semi-pantograph disconnector type DSSP, up to 300 kv Maximum reliability and minimal maintenance

Semi-pantograph disconnector type DSSP, up to 300 kv Maximum reliability and minimal maintenance Semi-pantograph disconnector type DSSP, up to 300 kv Maximum reliability and minimal maintenance Semi-pantograph disconnector type DSSP, up to 300 kv Maximum reliability and minimal maintenance 2 Semi-pantograph

More information

SF6 GAS INSULATED METAL ENCLOSED SWITCHGEAR (GIS)

SF6 GAS INSULATED METAL ENCLOSED SWITCHGEAR (GIS) SF6 GAS INSULATED METAL ENCLOSED SWITCHGEAR (GIS) About company The «Elektroapparat» plant starts its operation in 1922 as a plant manufacturing high-voltage electrical equipment. During the first two

More information

Fuse-links type CEF-S Rated voltages: 6/12 kv 30/40.5 kv Rated currents: 6.3 A 63 A

Fuse-links type CEF-S Rated voltages: 6/12 kv 30/40.5 kv Rated currents: 6.3 A 63 A DISTRIBUTION SOLUTIONS Fuse-links type CEF-S Rated voltages: 6/12 kv 30/40.5 kv Rated currents: 6.3 A 63 A Superior performance versus standard fuses ensuring up to 40% faster protection in case of low

More information

15 kv and 25 kv Thru-Bushings

15 kv and 25 kv Thru-Bushings Page 1 2001 ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric strength, dielectric loss and power factor Choice of shapes allows design innovation

More information

MEDIUM VOLTAGE PRODUCT. KECA 80 C85 Current Sensor Instructions for installation, use and maintenance

MEDIUM VOLTAGE PRODUCT. KECA 80 C85 Current Sensor Instructions for installation, use and maintenance MEDIUM VOLTAGE PRODUCT KECA 80 C85 Current Sensor Instructions for installation, use and maintenance 2 KECA 80 C85 CURRENT SENSOR INSTRUCTIONS FOR INSTALLATION, USE AND MAINTENANCE Scope of Contents 2

More information

Solid Dielectric Load Break Switch SPECIFICATION. 25kV, 630A, 4 WAYS, 4 WAYS SWITCHED PADMOUNTED VACUUM LOAD INTERRUPTER

Solid Dielectric Load Break Switch SPECIFICATION. 25kV, 630A, 4 WAYS, 4 WAYS SWITCHED PADMOUNTED VACUUM LOAD INTERRUPTER Solid Dielectric Load Break Switch SPECIFICATION 25kV, 630A, 4 WAYS, 4 WAYS SWITCHED PADMOUNTED VACUUM LOAD INTERRUPTER MANUALLY OPERATED / REMOTELY OPERATED DEAD FRONT PADMOUNTED VACUUM LOAD INTERRUPTING

More information

Eaton s Cooper Power Systems

Eaton s Cooper Power Systems Page: 1 of CERTIFIED TEST REPORT Eaton s Cooper Power Systems 600 Amp - 35 kv Class Deadbreak Bushing With Internal Ground Screen Design Qualification Tests December 17, 2013 Supersedes 10/20 2013 Eaton

More information

Electronic overload relays EF205 and EF370

Electronic overload relays EF205 and EF370 Data sheet Electronic overload relays EF205 and EF370 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays. Motor

More information

OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) kV to 550kV up to 5000A IEC

OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) kV to 550kV up to 5000A IEC OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) 1800 24kV to 550kV up to 5000A IEC 60137-2008 Features If you need any transformer bushing proven in operation conditions around the world, Trench

More information

Protection and Connection Motorized and automatic transfer switches IEC Technical guide

Protection and Connection Motorized and automatic transfer switches IEC Technical guide Protection and Connection Motorized and automatic transfer switches IEC 61439 Technical guide Motorized change-over switches Uninterrupted power supply with motorized functionality ABB offers a wide variety

More information

PNO Condenser Bushings from 52 kv to 420 kv Oil-to-air - Oil-Impregnated Paper

PNO Condenser Bushings from 52 kv to 420 kv Oil-to-air - Oil-Impregnated Paper GE Grid Solutions PNO Condenser Bushings from 52 kv to 420 kv Oil-to-air - Oil-Impregnated Paper PNO bushings are capacitance graded bushings with an oil impregnated paper core. PNO bushings are conform

More information

25-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp

25-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp Page 1 2018 Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other Component 15 kv or 25 kv Separable Insulated Connector (elbow) Equipment Connection Power Cable Power Cable ELRIM Cycloaliphatic

More information

Live Tank Circuit Breakers Buyer s Guide - Section LTB family

Live Tank Circuit Breakers Buyer s Guide - Section LTB family Live Tank Circuit Breakers Buyer s Guide - Section LTB family Table of contents Page Introduction 3 Auto-Puffer 8 Design features and advantages: LTB circuit breaker family 10 Technical catalogue LTB circuit

More information

Guideline No.: E-07(201610) E-07 TRANSFORMERS. Issued date: October 28,2016. China Classification Society

Guideline No.: E-07(201610) E-07 TRANSFORMERS. Issued date: October 28,2016. China Classification Society Guideline No.: E-07(201610) E-07 TRANSFORMERS Issued date: October 28,2016 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection and

More information

High Voltage Technology & Testing

High Voltage Technology & Testing The Power of Trust. The Future of Energy. HIGH VOLTAGE TESTING Qualification testing, condition assessment, and forensic analysis Manufacturers and utility users of high-voltage electrical equipment face

More information

35-kV 200-kV BIL Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp

35-kV 200-kV BIL Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp Page 1 2018 Grounded Metal Equipment Plate Equipment Connection 35 kv Separable Insulated Connector (elbow) Bus Bar or Other Component Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other

More information

Medium Voltage Metal-Enclosed Switches

Medium Voltage Metal-Enclosed Switches Medium Voltage Metal-Enclosed Switches Outdoor Medium Voltage Switch.1 Introduction Product Selection Guide....................................2 Medium Voltage Switch MVS Product Description......................................

More information

Inductive voltage transformers

Inductive voltage transformers Inductive voltage transformers Outdoor operation SF 6 -gas insulated EGF (245 550) kv General description Voltage transformers type EGF are used in high voltage substations within the 245 550 kv range.

More information

Inductive voltage transformers

Inductive voltage transformers Inductive voltage transformers Outdoor operation SF 6 -gas insulated EGF (245 550) kv General description Voltage transformers type EGF are used in high voltage substations within the 245 550 kv range.

More information

ABB MEASUREMENT & ANALYTICS DATA SHEET. TEIP11 I/P signal converter for standard signals

ABB MEASUREMENT & ANALYTICS DATA SHEET. TEIP11 I/P signal converter for standard signals ABB MEASUREMENT & ANALYTICS DATA SHEET TEIP11 I/P signal converter for standard signals 2 TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS DS/TEIP11-EN REV. D Flow in air pressure Proven and reliable concept

More information

High Voltage Surge Arresters Buyer s Guide Section PEXLIM R

High Voltage Surge Arresters Buyer s Guide Section PEXLIM R High Voltage Surge Arresters Buyer s Guide Section PEXLIM R Zinc Oxide Surge Arrester PEXLIM R Protection of switchgear, transformers and other equipment in high systems against atmospheric and switching

More information

35-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp

35-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp Page 1 2018 Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other Component 35 kv Separable Insulated Connector (elbow) Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other

More information

Product Group Brochure. PS Range Capacitor Vacuum Switches

Product Group Brochure. PS Range Capacitor Vacuum Switches Product Group Brochure PS Range Capacitor Vacuum Switches Introduction ABB introduces the latest range of PS capacitor vacuum switches. Building on the proven PS switch design, new single phase and three

More information

MEDIUM VOLTAGE PRODUCT. KECA 250 B1 Current Sensor Instructions for installation, use and maintenance

MEDIUM VOLTAGE PRODUCT. KECA 250 B1 Current Sensor Instructions for installation, use and maintenance MEDIUM VOLTAGE PRODUCT KECA 250 B1 Current Sensor Instructions for installation, use and maintenance 2 KECA 80 C184; KECA 80 C216 CURRENT SENSORS INSTRUCTIONS FOR INSTALLATION, USE AND MAINTENANCE Scope

More information

Product Specification Guide. Title: Southern States 72 kv RLSwitcher Vertical Interrupter Style Reactor Switcher

Product Specification Guide. Title: Southern States 72 kv RLSwitcher Vertical Interrupter Style Reactor Switcher TABLE OF CONTENTS PAGE 1.0 SCOPE... 2 2.0 STANDARDS... 2 3.0 DESIGN REQUIREMENTS... 2 3.01 Service Conditions... 2 3.02 Ratings... 3 3.03 Interrupter... 3 3.04 SF6 Gas System... 4 3.05 Terminal Pads...

More information

Guideline No.: E-07(201501) E-07 TRANSFORMERS. Issued date: October 20,2015. China Classification Society

Guideline No.: E-07(201501) E-07 TRANSFORMERS. Issued date: October 20,2015. China Classification Society Guideline No.: E-07(201501) E-07 TRANSFORMERS Issued date: October 20,2015 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection and

More information

Product brochure. Gas-insulated switchgear ELK-04 C, 145 kv Modular and reliable

Product brochure. Gas-insulated switchgear ELK-04 C, 145 kv Modular and reliable Product brochure Gas-insulated switchgear ELK-04 C, 145 kv Modular and reliable ABB and 50 years of GIS innovation ABB is a leader in power and automation technologies that enable utility and industry

More information

MEDIUM VOLTAGE PRODUCT. KECA 80 D85 Current Sensor Instructions for installation, use and maintenance

MEDIUM VOLTAGE PRODUCT. KECA 80 D85 Current Sensor Instructions for installation, use and maintenance MEDIUM VOLTAGE PRODUCT KECA 80 D85 Current Sensor Instructions for installation, use and maintenance 2 KECA 80 D85 CURRENT SENSOR INSTRUCTIONS FOR INSTALLATION, USE AND MAINTENANCE Scope of Contents 2

More information

FIXED POWER FACTOR CORRECTION EQUIPMENT 5KV CLASS MEDIUM VOLTAGE SECTION Z

FIXED POWER FACTOR CORRECTION EQUIPMENT 5KV CLASS MEDIUM VOLTAGE SECTION Z PART 1 GENERAL 1.01 1.02 1.03 1.04 1.05 SCOPE The Contractor shall furnish and install fixed power factor correction equipment as specified herein and as shown on the contract drawings. This specification

More information

Thermal overload relay TF140DU and TF140DU-V1000

Thermal overload relay TF140DU and TF140DU-V1000 Data sheet Thermal overload relay TF140DU and TF140DU-V1000 Thermal overload relays are economic electromechanical protection devices for the main circuit. They are used mainly to protect motors against

More information

MEDIUM VOLTAGE AIR INSULATED ARC-RESISTANT LOAD BREAK AND DISCONNECT SWITCHES

MEDIUM VOLTAGE AIR INSULATED ARC-RESISTANT LOAD BREAK AND DISCONNECT SWITCHES MEDIUM VOLTAGE AIR INSULATED ARC-RESISTANT LOAD BREAK AND DISCONNECT SWITCHES Description JRS arc-resistant fused/non-fused load break and fused/non-fused disconnect switches are available for applications

More information

Outdoor live tank vacuum circuit breaker Type OVB-VBF for 24/36/40.5 kv applications

Outdoor live tank vacuum circuit breaker Type OVB-VBF for 24/36/40.5 kv applications Outdoor live tank vacuum circuit breaker Type OVB-VBF for 24/36/40.5 kv applications ABB a global leader ABB is a global leader in power and automation technologies that enable utility and industry customers

More information

Thermal overload relay TF65 and TF96

Thermal overload relay TF65 and TF96 Data sheet Thermal overload relay TF65 and TF96 Thermal overload relays are economic electromechanical protection devices for the main circuit. They are used mainly to protect motors against overload and

More information

Guideline No.: E-07(201712) E-07 TRANSFORMERS. Issued date: December 26, China Classification Society

Guideline No.: E-07(201712) E-07 TRANSFORMERS. Issued date: December 26, China Classification Society Guideline No.: E-07(201712) E-07 TRANSFORMERS Issued date: December 26, 2017 China Classification Society Foreword: This Guide is a part of CCS Rules, which contains technical requirements, inspection

More information

PORCELAIN INSULATORS

PORCELAIN INSULATORS Solid Core Station Post Insulator PORCELAIN INSULATORS It is an insulator of generally columnar shape, and it consists of one post insulator unit or an assembly of such units and is intended to give rigid

More information

Type SIMOPRIME A4, up to 24 kv, Air-Insulated Medium-Voltage Switchgear

Type SIMOPRIME A4, up to 24 kv, Air-Insulated Medium-Voltage Switchgear Circuit-Breaker www.siemens.com/energy Switchgear Type SIMOPRIME A4, up to 24 kv, Air-Insulated Medium-Voltage Switchgear s Technology Circuit-Breaker Switchgear Type SIMOPRIME, up to 17.5 kv, Air-Insulated

More information

Product Information. Neutral Wall Bushing GOFL

Product Information. Neutral Wall Bushing GOFL ABB Components Info-No. 2750 515-93en, Rev. 1 From / Date Product Information Neutral Wall Bushing GOFL Description Page Design 2 Voltage tap 2 Dimensions 2 Terminals 2 Mounting instruction Packing 4 Storing

More information

System pro M compact Supplementary protector S 200 PR for ring-tongue applications acc. to UL1077

System pro M compact Supplementary protector S 200 PR for ring-tongue applications acc. to UL1077 Data Sheet System pro M compact Supplementary protector S 200 PR for ring-tongue applications acc. to UL1077 2CDC021026S0011 2CDC021016S0012 The S 200 PR is a high-performance supplementary protector with

More information