ALR output Powerfull PROGRAMMABLE POWER SUPPLY 640 WATTS 0-32V 0-20A POWERFUL. Specifications

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "ALR output Powerfull PROGRAMMABLE POWER SUPPLY 640 WATTS 0-32V 0-20A POWERFUL. Specifications"

Transcription

1 $ PROGRAMMABLE POWER SUPPLY EAN CODE : output Powerfull POWERFUL ALR3220 VISUAL : Large graphic display SOFT-TOUCH : Sensitiv keypad CONNECTED : USB, RS232, RS485 & 0-10V isolated LabVIEW as a standard PERFORMANCE : output in the rear-panel,used for remote-sensing FUNCTIONS : square, positive and negative ramp, rise or fall time ELEGANT : New design and feathery SPACE-SAVING : vertical & COMPACT BOX / 640W PRACTICAL : Lightweight with built-in handle and cord storage area. QUIET : Silent temperature-controlled fan cooling. LOCKING : configuration & stand-by 640 WATTS 0-32V 0-20A LabVIEW ULTRA-COMPACT!!! C Voltage Floating outputs : on 4mm safety terminals in the front-panel, and on screw terminal block for 2.5mm² on the rear-panel. Automatic constant voltage operation. Adjustable from 0 to Volts (0 to ±10mV) ; resolution : 10mV. Setting accuracy : < 0,03% that to say ±10 mv. Regulation : < 50mV for a load change from 10 to 90%. < 1mV for a ±10% line change. Ripple : < 1mV rms including : < 3 mv peak to peak of noise (BP 20 MHz) < 15mV peak to peak of switching spikes Internal resistance : < 4mΩ. Display : 4 digits on graphic LCD. Accuracy measurement : < 0,03% that to say ±10 mv. Automatic constant current operation. Adjustable from 0 to Amps ; resolution : 10mA. Setting accuracy : < 0,05% that to say ±10 ma. Regulation : < 10mA for a load charge from 10 to 90%. < 1mA for a ±10% line charge. Ondulation : < 6mA peak to peak or 2mA rms. Display : 4 digits on graphic LCD. Accuracy measurement : < 0,05% that to say ±10 ma. s Against short-circuits, by current regulation. Against overtemperature by fan and thermal circuit-breaker. Against overcurrent on main input, by internal fuses. Various and functions Dispaly : Graphic LCD 128 x 64 pixels with white backlight. Visualization of all parameters CV (Constant Voltage) mode or CC (Constant ) Memories : 16 including 15 configurable. OVP/OCP : Against overvoltage and overcurrent, adjustable from 0 to maxi. Functions : 6 available on U or I (Arbitrary, square, rising and falling periodically ramp, rise or fall time single shot). Time adjustement from 10ms to 60mn. Remote sensing : automatic function on the front side output. 4 wires mode on the back-side's terminal blocks. Correction of the voltage drop in the wires : 2V Standby : output, enable / disabled and standby of the power supply. Interfaces All the interfaces are insulated of the output (150V max). USB, RS232 and RS485 as a standard. LabVIEW's drivers as a standard. Controller 0 10V : for U and I by direct input 0-10V or potentiometer 10K or adjustable resistance 10K. In the back side on disconnect scribe terminal blocks. : Class I, enhanced safety between mains input and outputs. Complies with EN , CAT II. CEM : Complies with EN and EN Input voltage : Volts ±10%, 50 / 60Hz. Mains input : Socket CE14 with C13, 2 poles + earth cable removable Power consumption : 770W maxi. Efficiency : > 84% of the maxi powerful. Operating temperature : +5 to +40 C. Coefficient of temperature / C : 0.01% for the voltage ; 0.05% for the current. Voltage on the earth : 100V Max. Presentation : Front-panel with sensitiv keypad, rear-panel with handle and cord storage area, metallic case with epoxy finish. 3

2 PROGRAMMABLE POWER SUPPLY EAN CODE : outputs Powerfull DOUBLE ALR3206D VISUAL : Large graphic display SOFT-TOUCH : Sensitiv keypad CONNECTED : USB, RS485 & 0-10V isolated LabVIEW as a standard PERFORMANCE : output in the rear-panel,used for remote-sensing COUPLING : Auto mode : Series, Parallel, Tracking FUNCTIONS : square, positive and negative ramp, rise or fall time ELEGANT : New design and feathery SPACE-SAVING : vertical & COMPACT BOX / 390W PRACTICAL : Lightweight with built-in handle and cord storage area. QUIET : Silent temperature-controlled fan cooling. LOCKING : configuration & stand-by 390 WATTS 2 x 0-32 V 0-6 A or 1 x ± 0-32 V 0-6 A or 1 x 0-64 V 0-6 A or 1 x 0-32 V 0-12 A LabVIEW ULTRA-COMPACT!! $ ' C Floating outputs : on 4mm safety terminals in the front-panel, and on spring terminal block with levers for 2mm² on the rear-panel. Automatic constant voltage and current operation. Channel 1 and 2 MASTER AND SLAVE Independent Tracking Series Parallel Output voltage 2 x 0-32 V ± 0-32 V 0-64 V 0-32 V Minimum voltage ± 10 mv ± 10 mv ± 20 mv ± 10 mv Adjustement accuracy 0.03% or ±10 mv (20 mv in series) Ripple (mv rms) < 0.7 mv < 0.7 mv < 1.5 mv < 1 mv Pics of commutation (BP 20 MHz) < 15 mvpp < 15 mvpp < 30 mvpp < 30 mvpp Regulation / load 0 to 100% 12 mv 12 mv 24 mv 40 mv Regulation / source ±10% 1 mv 1 mv 2 mv 1 mv Time of answer load 10 to 90% 2 ms 2 ms 2 ms 5 ms Display resolution 10mV 10mV 20mV 10mV Accuracy measurement 0.03% or ±10 mv (20 mv in series) Display 4 digits + parameters on graphic LCD Output current 2 x 0-6 A ± 0-6 A 0-6 A 0-12 A Minimum current 2 ma 2 ma 2 ma 10 ma Adjustement accuracy 0.03% or ±2 ma (10 ma in series) Ripple (marms) <1 ma <1 ma <1 ma <1 ma Regulation / load 0 to 100% 1 ma 1 ma 2 ma 2 ma Regulation / source ±10% 1 ma 1 ma 1 ma 1 ma Display resolution 2 ma 2 ma 2 ma 10 ma Accuracy measurement 0.03% or ±2 ma (10 ma in series) Display 4 digits + parameters on graphic LCD s Against short-circuits, by current regulation. Against overtemperature by fan and thermal circuit-breaker. Against overcurrent on main input, by internal fuses. Various and functions Dispaly : Graphic LCD 128 x 64 pixels with white backlight. Visualization of all parameters (CV, CC, RMT, etc...) Memory : 16, including 15 configurable. OVP/OCP : Against overvoltage and overcurrent, adjustable from 0 to maxi. Functions : 6 available on U or I (Arbitrary, square, rising and falling periodically ramp, rise or fall time single shot). Time adjustement from 10ms to 60mn. Remote sensing : 4 wires mode on the back-side's terminal blocks. Correction of the voltage drop in the wires : 2V Standby : output, enable / disabled and standby of the power supply. Interfaces All the interfaces are insulated of the output (150V max). USB and RS485 are standard. LabVIEW's drivers as a standard. Controller 0 10V : by direct input 0-10V for U for each channel or for U & I for channel 1 or potentiometer 10K or adjustable resistance 10K. In the back side on disconnect scribe terminal blocks. : Class I, enhanced safety between mains input and outputs. Complies with EN , CAT II. CEM : Complies with EN and EN Input voltage : Volts ±10%, 50 / 60Hz. Mains input : socket C14 with C13 2 poles + earth cable removable Power consumption : 475W maxi. Efficiency : > 81% of the maxi powerful. Operating temperature : +5 to +40 C. Coefficient of temperature / C : 0.01% for the voltage and the current. Voltage on the earth : 100V Max. Presentation : Front-panel with sensitiv keypad, rear-panel with handle and cord storage area, metallic case with epoxy finish. 5

3 ADJUSTABLE POWER SUPPLY EAN CODE : TRIPLE AL 936N EASY : Direct digital display of voltage and current, even in the series or parallel mode. SURE : Automatic disconnection each time the master and slave channel configuration is changed. COMPLETE : Third channel with fixed or variable position and voltage or current display. EFFECTIVE : Idc adjustment independent of load. QUIET : Silent temperature-controlled fan cooling. 200 WATTS 2 X 0-30V 0-3A or 1 X ± 0-30V 0-3A or 1 X 0-60V 0-3A or 1 X 0-30V 0-6A + 1 X 2-5,5V 3A or 1 X 5,5-15V 1A % C &! % $ C! $ CHANNELS MASTER AND SLAVE AUXILIARY Configuration Independent Tracking Series Parallel Variable Variable Output voltage 2x 0-30V ± 0-30V 0-60V 0-30V 2-5,5V 5,5-15V Minimum voltage ± 10mV ± 10mV ± 20mV ± 10mV < 2V - Ripple (mv rms) 1mV 1mV 1mV 1mV 1mV 1mV Load regulation from 0 to 100% 12mV 12mV 50mV 24mV 12mV 10mV Line regulation from -6 to +7% 5mV 5mV 5mV 5mV 5mV 1mV Internal resistance 4mΩ 4mΩ 16mΩ 4mΩ 4mΩ 4mΩ Resp. for 10 to 90% load change 30µs 30µs 30µs 30µs 100µs 60µs Display resolution 100mV 100mV 100mV 100mV 10mV 100mV Display 14 mm 3 digit LED digital voltmeter Output current 2x 0-3A ± 0-3A 0-3A 0-6A 3A 1A Minimum current 10mA 10mA 10mA 20mA - - Ripple (ma rms) 1mA 1mA 1mA 4mA - - Load regulation from 0 to 100% 2mA 2mA 4mA 8mA - - Line regulation from -6 to +7% 1mA 1mA 1mA 5mA - - Display resolution 10mA 10mA 10mA 10mA 10mA 10mA Display 14 mm 3 digit LED digital ammeter Power supplies A and B (master and slave) The Standby mode disconnects the output terminals. It is automatic upon a change of mode. The Idc push-button shorts the output in the standby mode. It is used for setting Imax. I ndicators : green LED for voltage regulation red LED for current regulation. Display : automatic display switching depending on selected configuration. AUXILIARY power supply The Display button switches the display between voltage and current. The voltage is continuously adjustable from 2 to 15V. The max current goes from 3A to 1A after 5,5V. Short circuit protection, by current regulation. Overtemperature protection, by temperature-controlled fan, thermal circuit-breaker and relay. T ransformer primary overcurrent protection, by fuse. : Class I, enhanced safety between mains input and outputs. Complies with EN , overvoltage category II, pollution degree 2. Toroidal transformer, class II, complies with EN EMC : Complies with EN , performance criteria B, and EN 55011, ISM Group I, Class B. Mains input : Socket C14 with C13 removable cable (2 poles + earth). Power consumption : 410 VA. Dielectric strength : 2300V between input, output and chassis. Outputs : safety terminals (VDE 0110 standard and BG certified), and safety inverted earth terminal. Presentation : screen-printed polycarbonate front panel, metalcase, epoxy finish. 7

4 ADJUSTABLE POWER SUPPLY EAN CODE : DOUBLE ALR3003D PRATICAL : Digital display of voltage and current. EASY : Automatic mode select button : separate, tracking and series. PRECISE : Fine voltage adjustment. QUIET : Silent temperature-controlled fan cooling. 180 WATTS 2 X 0-30V 0-3A or 1 X ± 0-30V 0-3A or 1 X 0-60V 0-3A or 1 X 0-30V 0-6A* & $ C! $ & C! $ CHANNELS MASTER AND SLAVE Independent Tracking Series Output Voltage 2x0-30V ± 0-30V 0-60V Minimum Voltage ± 10mV ± 10mV ± 20mV Ripple (mv rms.) 1mV 1mV 1mV Load regulation from 0 to 100% 12mV 12mV 50mV Line regulation from -6 to +7% 5mV 5mV 5mV Internal resistance 4mΩ 4mΩ 16mΩ Resp. for 10 to 90% load charge 30µs 30µs 30µs Dispaly resolution 100mV 100mV 100mV Display 14mm 3 digit LED Voltmeter Output current 2x0-3A ± 0-3A 0-3A Minimum current 10mA 10mA 10mA Ripple (ma rms.) 1mA 1mA 1mA Load regulation from 0 to 100% 2mA 2mA 4mA Line regulation from -6 to +7% 1mA 1mA 1mA Dispaly resolution 10mA 10mA 10mA Display 14mm 3 digis LED Ammeter : Class I, enhanced safety between mains input and outputs. Complies with EN , overvoltage category II, pollution degree 2. Toroidal isolation transformer, class II, complies with EN EMC : Complies with EN , performance criteria B, and Power Supplies A and B (master and slave) The "Tracking/Series" mode internally connects the - terminals of the master and + terminals of the slave (mid point). All adjustments are made from the slave power supply. The parallel mode* (external connection) provides up to 6 amperes. Indicators : green LED for voltage regulation red LED for current regulation. Display of voltage and current on 14 mm 3 digit red LED displays. Short circuit protection, by current regulation. Overtemperature protection, by temperature-controlled fan, thermal circuit-breaker and relay. T ransformer primary overcurrent protection, by fuse. Mains input : Socket C14 with C13 removable cable (2 poles + earth). Power consumption : 400 VA. Dielectric strength : 2300V between input, output and chassis. Outputs : Presentation : safety sockets and safety inverted earth socket. screen-printed polycarbonate front panel, meta case, epoxy finish. 8

5 ADJUSTABLE POWER SUPPLY EAN CODE : SIMPLE AL 924A PRACTICAL : Digital display of voltage and current. PRECISE : Coarse and fine voltage adjustment. - Adjustable current from 0 to 10A or 0 to 1A. USEFUL : Automatic constant voltage or current operation. PROTECTED : Short circuit protection. ' &!! $ 300 WATTS 0-30V 0-10A & C $ C Voltage Floating outputs on 4 mm safety terminals. Automatic constant voltage operation. Adjustable from 0 to 30V (0 to + or -5mV) with fine adjustment (about 2 Volts). Regulation : < 40mV for a load variation from 0 to 100%. < 25mV for a 10% line variation. Ripple : < 3 mv peak to peak or 1 mv rms. Internal resistance: < 4 mω. Indicator : green LED for voltage regulation. Display : 14mm 3 digit LED digital voltmeter. Resolution : 100 mv. Automatic constant current operation. Two selectable current ranges : 10A or 1A. Adjustable from 0 to 10A or from 0 to 1A, depending on the selected range. Regulation : < 10 ma for a 10% line charge. < 20 ma for a load change from 0 to 100%. Ripple : < 10 ma peak to peak or 3,5 ma rms. Indicators : red LED for current regulation. Display : 14 mm 3 digit LED digital ammeter. Resolution : 10 ma on 1A range, 100 ma on 10A range : Class I, enhanced safety between mains input and outputs. Complies with EN , overvoltage category II, pollution degree 2. EMC : Complies with EN , performance criteria B, and Mains input : Socket C14 with C13 removable cable (2 poles + earth). Power consumption : 620 VA. Dielectric strength : 2300V from input to output, 1350V from input to chassis. Outputs : safety terminals (VDE 0110 standard and BG certified), and safety inverted earth terminal. Presentation : screen-printed polycarbonate front panel, metal case, epoxy finish. Short circuit protection, by current regulation. Overtemperature protection, by fan, by thermal circuit-breaker and by relay on the transformer. Transformer primary overcurrent protection, by fuse. 9

6 ADJUSTABLE POWER SUPPLY EAN CODE : SIMPLE AL 781NX PRACTICAL : Digital display of voltage and current. PRECISE : Coarse and fine voltage adjustment. - Adjustable current from 0 to 5A or 0 to 1A. USEFUL : Automatic constant voltage or current operation. PROTECTED : Short circuit protection. ' &!! $ 150 WATTS 0-30V 0-5A & " C ' C Voltage Floating outputs on 4 mm safety terminals. Automatic constant voltage operation. Adjustable from 0 to 30V (0 to + or -5mV) with fine adjustment (about 2,5 Volts). Regulation : < 20mV for a load variation from 0 to 100%. < 15mV for a 10% line variation. Ripple : < 3 mv peak to peak or 1 mv rms. Internal resistance : < 4 mω. Indicators : green LED for voltage regulation. Display : 14mm 3 digit LED digital voltmeter. Resolution : 100 mv. Automatic constant current operation. Two selectable current ranges : 5A or 1A. Adjustable from 0 to 5A or from 0 to 1A, depending on the selected range. Regulation : < 10 ma for a 10% line charge. < 15 ma for a load change from 0 to 100%. Ripple : < 6 ma peak to peak or 2,1 ma rms. Indicators : red LED for current regulation. Display : 14mm 3 digit LED digital ammeter. Resolution : 10 ma. : Class I, enhanced safety between mains input and outputs. Complies with EN , overvoltage category II, pollution degree 2. EMC : Complies with EN , performance criteria B, and Mains input : Socket C14 with C13 removable cable (2 poles + earth). Power consumption : 315 VA. Dielectric strength : 2300V from input to output, 1350V from input to chassis. Outputs : safety terminals (VDE 0110 standard and BG certified), and safety inverted earth terminal. Presentation : screen-printed polycarbonate front panel, metal case, epoxy finish. Short circuit protection, by current regulation. Overtemperature protection, by thermal circuit-breaker and by relay on the transformer. Transformer primary overcurrent protection, by fuse. 10

7 ADJUSTABLE POWER SUPPLY EAN CODE : SIMPLE ALR3003 PRACTICAL : Digital display of voltage and current. - Cord housing. PRECISE : Coarse and fine voltage adjustment. USEFUL : Automatic constant voltage or current operation. PROTECTED : Short-circuit protection. QUIET : Controlled fan cooling.!!! & & 90 WATTS 0-30V 0-3A '! C! ' Voltage Automatic constant voltage operation. Adjustable from 0 to 30 Volts (0 to ± 10 mv) with fine adjustment (about 2 Volts). Regulation : < 12 mv for a load variation from 0 to 100%. < 5 mv for a line variation of 10%. Ripple : < 3 mv peak to peak or 1 mv rms. Internal resistance : < 4 mω. Display : 14 mm 3 digits LED digital voltmeter. Resolution : 100 mv Automatic constant current operation. Adjustable from 0 to 3 Amps. Regulation : < 1 ma for a line charge of 10 %. < 2 ma for a load charge from 0 to 100%. Ripple : < 1 ma rms. Display : 14 mm 3 digits LED digital ammeter. Resolution : 10 ma : Class II, Safety Extra Low Voltage (SELV) outputs with insulation enhanced transformer. Complies with EN , overvoltage category II, pollution degree 2. EMC : Complies with EN , performance criteria B, and level : IP 21. Input voltage : 230 V ±10%, 50 / 60 Hz. Main input : Cord with 2 poles immovable. Power consumption : 176 VA max. Dielectric strength : 3000 V between the input and the output. Presentation : screen-printed polycarbonate front panel, metal case with cord housing, epoxy finish. s Short-circuit protection by current regulation. Overtemperature protection by temperature-controlled fan, relay and thermal circuit-breaker. Transformer primary and secondary overcurrent protection by fuse. 11

8 ADJUSTABLE POWER SUPPLY EAN CODE : TRIPLE + INTERFACES AL 991S COMPLETE : Three outputs available simultaneously. PRATICAL : Digital voltage display. USEFUL : Setting memory. COMPATIBLE : RS232, USB* and LABVIEW interfaces. PROTECTED : Short circuit protection. 48 WATTS RS232 + LABVIEW + USB* 0 to ± 15V 1A or 0 to 30V 1A and 2 to 5,5V 3A and -15 to +15V 0,2A LabVIEW ' $! C *OPTION : USBRS232! $ Voltage Three outputs available simultaneously : - Power supply A : adjustable from 0 to ±15 Volts balanced. or 0 to 30V with the -15V terminal as reference. - Power supply B: adjustable from + 2 to + 5,5 Volts. - Power supply C: adjustable from - 15 to + 15Volts. Voltage adjustment : push-button selection of output A, B or C. Voltage incremented and decremented by four push-buttons : -1 V + 1 V - 0,1 V + 0,1V Automatic storage of the three voltage settings. Regulation : < 20mV for a load variation from 0 to 100%. < 10mV for a 10% line variation. Ripple : < 3 mv peak to peak or 1 mv rms. I ndicators : Three red LEDs showing the selected output for display and adjustment. Display : 14 mm 3 digit LED digital voltmeter for the three outputs. Resolution : 100 mv. EMC : Class I, enhanced safety between mains input and outputs. Complies with EN , overvoltage category II, pollution degree 2. : Complies with EN , performance criteria B, and Mains input : Socket C14 with C13 removable cable (2 poles + earth). s Max I : 1A on output A. 3A to 5,5 Volts and 1,5A to 2 Volts on output B. 0,2A on output C. Display : limiting on one output causes the display to blink ; it shows : Ic.A, Ic.b, Ic.C or +Ic, depending on the overloaded output(s). Short circuit protection, by current limit. Transformer primary overcurrent protection, by fuse. Chassis ground output on 4 mm inverted safety socket. Interface RS-232 link, 9-way male SUB-D plug. USB option: Kit includes an adaptator null modem und RS232 cable Software LG991S for Windows95* or + LG991S LV and base VI under LabVIEW** Softwares are available for download on website (*is a registered trademark of Microsoft Co.) (** (*is a registered trademark of National Instruments.) Power consumption : 100 VA max. Dielectric strength : 2300V from input to output, 1350V from input to chassis. Presentation : screen-printed polycarbonate front panel, metal case, epoxy finish. 12

9 ADJUSTABLE & MULTIPLE POWER SUPPLY EAN CODE : DOUBLE AC/DC ALR3002M COMPLETE : DC and AC voltages available simultaneously. POWERFUL : generator. PRACTICAL: No common reference. - Cord housing. PROTECTED : The DC output is protected by current regulation. - The AC outputs are protected by auto reset thermal circuit-breakers. 120 WATTS 0-5, 6, 12 or 30V 0-25mA, 250mA or 2,5A DC and 6 or 12 or 24V 5A AC! & &!! ' " " C DC outputs Automatic constant voltage operation. Four choices of voltage ranges with adjustement by trimer from 0 to max : 0 to 5V, 0 to 6V, 0 to 12V or 0 to 30V. Regulation : < 10 mv for a load variation from 0 to 100%. < 5 mv for a line variation from -6 +7%. Ripple : < 3 mv peak to peak or 1mV rms. Internal resistance : < 5 mω. Display : 14mm 3 digits LED digital voltmeter. Resolution : 10mV for 5 and 6V and 100 mv for 12 and 30V. Automatic constant current operation. Three choices of current ranges with adjustement by trimer from 0 to max : 0 to 25mA ; 0 to 250mA ; 0 to 2,5 Amps. Regulation : < 2 % for a load change from 0 to 100%. Ripple : < 1 ma rms. Display : 14mm 3 digits LED digital ammeter. Resolution : 100µA on 25mA range, 1mA on 250mA range, 10mA on 2,5A range. s Short circuit protections by current regulation. Overtemperature protection by transformer secondary switching relay and thermal circuit-breakers. Transformer primary overcurrent protections by fuse. AC outputs Three outputs with common point. Voltages : 6 Volts, 12 Volts and 24 Volts. No-load voltage 5% maximum above rated voltage. Max I : 5 Amps on 6,12, or 24V. s Secondary overcurrent protection by auto-reset thermal circuit-breakers. Precautions The AC and DC circuits can be used simultaneously but with a max power of 120W. EMC : Class II, Safety Extra Low Voltage (SELV) outputs with insulation enhanced transformer. Complies with EN , overvoltage category II, pollution degree 2. : Complies with EN , performance criteria B, and level : IP 21. : Transformer primary overcurrent protection, by fuse. Main input : 2 poles cable immovable. Power consumption : 250 VA max. Dielectric strength : 3000V from input to output. Presentation : screen-printed polycarbonate front panel, metal case with cord housing, epoxy finish. 13

10 MULTIPLE POWER SUPPLY EAN CODE : DOUBLE AC/DC AL 843A COMPLETE : DC and AC voltages available simultaneously. PRACTICAL : No common reference. PROTECTED : The DC output is protected by fold-back current limiting. The AC outputs are protected by auto-reset thermal circuit-breakers. 120 WATTS 6 or 12V 10A or 24V 5A DC and AC $ & % " C! & C! $ DC outputs Three switchable outputs : 6V, 12V or 24V. Accuracy : ± 1% Regulation : < 40 mv at 6 and 12 V outputs for a load variation from 0 to 100%. < 20 mv at 24 V output for a load variation from 0 to 100%. Ripple : < 5 mv peak to peak or 1,8 mv rms. Internal resistance : < 4 mω. Max I : 10A at 6 or 12V output. 5A at 24V output. Short circuit protection by fold-back current limit, allowing continuous short circuit without overheating. AC outputs Three outputs with common point. Voltages : 6 Volts, 12 Volts and 24 Volts ± 10%. No-load voltage 5% maximum. Max I : 10A at 6 and 12V outputs. 5A at 24V output. Secondary overcurrent protection by auto-reset thermal circuit-breakers. Precautions The AC and DC circuits can be used simultaneously but with a max power of 120W. EMC : Class I, enhanced safety between mains input and outputs. Complies with EN , overvoltage category II, pollution degree 2. : Complies with EN , performance criteria B, and Transformer primary overcurrent protection, by fuse. Mains input : Socket C14 with C13 removable cable (2 poles + earth). Power consumption : 250 VA max. Dielectric strength : 3700V from input to output, 2200V from input to chassis. Presentation : screen-printed polycarbonate front panel, metal case, epoxy finish. 14

11 MULTIPLE POWER SUPPLY EAN CODE : DOUBLE AC/DC AM COMPLETE : DC and AC voltages available simultaneously. PRACTICAL : No common reference. - AC and DC power-on indicators. PROTECTED : The DC output is protected by current regulation. - The AC outputs are protected by auto-reset thermal circuit-breakers. 120 WATTS 6 or 12V 5A DC and AC C $ ' " C $ DC outputs Two switchable outputs : 6 Volts or 12 Volts. Accuracy : ± 1% Regulation : < 20mV for a load variation from 0 to 100%. < 5mV for a 10% line variation. Ripple : < 3 mv rms including : <3mV peak to peak of the signal at 100 KHz <4mV peak to peak of the signal at 100 Hz <12mV peak to peak of switching peak Hold up time : 25ms at half load and 12ms at full load (190V line input). Indicator : green power-on LED indicator. Max I Idc : 5A at 6 or 12V output. : 5,5A. Short circuit protection by current limiting, Overcurrent protection on source by fuse on main input AC outputs Two outputs with common point. Voltages : 6 Volts and 12 Volts + or - 5%. No-load voltage 10% maximum. Indicator: green power-on LED indicator. Max I : 5A at 6V or 12V output. Short circuit and overcurrent protection by auto-reset thermal circuit-breakers. Precautions Power supply max. power is of 120 Watts The AC and DC circuits can be used simultaneously. EMC Input voltage Mains input : Class II, double insulation Complies with EN , overvoltage category II, pollution degree 2. : Complies with EN , performance criteria B, and : 230V ±10%, 50 / 60 Hz. : C8 socket with CEI320 C7 removable cable (2 poles double insulation). Power consumption : 145 VA max. : against overcurrent at the input by fuse level : IP 30 Dielectric strength : 3000V between input to output. Presentation : Metal case with epoxy finish 15

12 AC POWER SUPPLY & DC RECTIFIER EAN CODE : DOUBLE AC/DC AM COMPLETE : DC rectified and AC voltages available simultaneously. PRACTICAL : AC and DC power-on indicators. PROTECTED : The DC rectifier output and the AC outputs are protected by auto-reset thermal circuit-breakers. 120 WATTS 6V 20A 12V 10A DC and AC " C "! C ' $ DC outputs Two switchable outputs : 6 Volts or 12 Volts. Voltage rectified only Indicator : green power-on LED indicator. Max I : 20A at 6V output. : 10A at 12V output Short circuit protection by current limiting, Overcurrent protection on source by fuse on main input AC outputs Two outputs with common point. Voltages : 6 Volts and 12 Volts + or - 5%. No-load voltage 10% maximum. Indicator: green power-on LED indicator. Max I : 20A at 6V output. or 10A at 12V output Short circuit and overcurrent protection by auto-reset thermal circuit-breakers. Precautions Power supply max. power is of 120 Watts The AC and DC outputs can be used simultaneously on circuits without common refrence. EMC Input voltage Mains input : Class II, double insulation Complies with EN , overvoltage category II, pollution degree 2. : Complies with EN , performance criteria B, and : 230V ±10%, 50 / 60 Hz. : double insulation cord with 2 poles immovable. Power consumption : 145 VA max. : against overcurrent at the input by fuse level : IP 30 Dielectric strength : 3000V between input to output. Presentation : Metal case with epoxy finish 16

13 UNIVERSELLE BENCH POWER SUPPLY EAN CODE : UNIVERSAL AL 841C UNIVERSAL : Choice of six voltages. PRACTICAL : ON/OFF switch. - Power-on indicator. PROTECTED : Short circuit protection. RESISTANT TO SHOCK : Polycarbonate case 12 WATTS 3 / 4,5 / 6 / 7,5 / 9 or 12V 1A ' ' $ % C &! & Voltage Output voltage : 3 V or 4,5 V or 6 V or 7,5 V or 9 V or 12 V selectable Accuracy : ± 4%. Regulation : < 20mV for a load variation from 0 to 100%. < 15mV for a 10% line variation. Ripple : 5 mv peak to peak or 1,8 mv rms. Internal resistance : < 20 mω. The max current is constant and independent of the selected output. Max I : 1 A. Indicator Green power-on LED indicator. : Class II - Safety Extra Low Voltage (SELV) output Complies with EN , overvoltage category II, pollution degree 2. EMC : Complies with EN , performance criteria B, and Mains input : C8 socket with CEI320 C7 removable cable (2 poles double insulation). ON/OFF control : toggle switch. Power consumption : 30 VA max. Dielectric strength : 3000Vac from input to output. Presentation : Polycarbonate case screen-printed. Short circuit protection, by current limit. Transformer primary overcurrent protection, by fuse. 27

14 SYMMETRIC BENCH POWER SUPPLY EAN CODE : V or 12V or 24V ALF1501D PRATICAL : ON/OFF switch. - Power-on indicator W available on the positive output alone. PRECISE : Output ripple < 3mV rms. - Output voltage adjustable from ±10 to ±15V. PROTECTED : against Short circuit. RESISTANT TO SHOCK 30 WATTS +/- 10 to 15V 1A or 12V 2,5A or 24V 1A ' ' $ C &!! ' Balanced-output power supply with common 0V. Floating outputs on 4-mm safety sockets. Ajustable output voltages : from ±10 to ±15V +15V output Regulation : < 15mV for a load variation from 0 to 100%. < 2mV for a line variation from 198 to 264 V. Ripple : < 3mV rms including : < 3mV peak to peak of switching signal < 8mV peak to peak of the signal at 100Hz < 10mV peak to peak of switching spikes -15V output Regulation : < 10mV for a load charge from 0 to 100%. < 2mV for a line charge from 198 to 264 V. Ripple : < 3mV rms including : < 2mV peak to peak of switching signal < 4mV peak to peak of the signal at 100Hz < 15 mv peak to peak of switching spikes 24V Output (Adjustable from 20 to 30V) Available between output + and - Regulation : < 15mV for a load charge from 0 to 100% < 2mV for a line charge from 198 to 264V Ondulation : < 5mV rms including: < 3mV peak to peak of the switching signal < 12mV peak to peak of the signal at 100Hz < 30mV peak to peak of switching spikes Indicators 2 Green +15V and -15V power-on LED indicator. +15V (alone) I max : 3A at 10V 2,5A at 12V 2A at 15V -15V (alone) I max : 1,1A in short-circuit condition 1A from 10 to 15V 24V (Adjustable from 20 to 30V) I max : 1A from 20 to 30V Power Max output power : 30W. I max ±15V : 1A s Against short-circuits by current limit and disjunction. Against overcurrent on source by fuse. : Class II, Safety Extra Low Voltage (SELV) Complies with EN , overvoltage category II, pollution degree 2. EMC : Complies with EN , performance criteria B, and level : IP30. Operating temperature : 5 to 40 C Input voltage : 198 to 264 V, 50 / 60 Hz. Mains input : C8 socket with CEI320 C7 removable cable (2 poles double insulation). Power consumption : 40W max. ON/OFF control : toggle switch Dielectric strength : 3000 V between input to output. Presentation : polycarbonate case screenprinted. 29

15 SYMMETRIC POWER SUPPLY EAN CODE : V or 12V or 24V ALF1502D PRATICAL : ON/OFF switch. - Power-on indicator W available on the positive output alone. PRECISE : Output ripple < 3mV rms. - Output voltage adjustable from ±10 to ±15V. PROTECTED : against Short circuit. RESISTANT TO SHOCK 60 WATTS +/- 10 to 15V 2A or 12V 5A or 24V 1A ' ' $! C &! " $ Balanced-output power supply with common 0V. Floating outputs on 4-mm safety sockets. Ajustable output voltages : from ±10 to ±15V. +15V output Regulation : < 15mV for a load variation from 0 to 100%. < 2mV for a line variation from 198 to 264 V. Ripple : < 3mV rms including : < 3mV peak to peak of switching signal < 5mV peak to peak of the signal at 100Hz < 15mV peak to peak of switching spikes -15V output Regulation : < 30mV for a load variation from 0 to 100%. < 2mV for a line variation from 198 to 264 V. Ripple : < 3mV rms including : < 4mV peak to peak of switching signal < 4mV peak to peak of the signal at 100Hz < 15 mv peak to peak of switching spikes 24V Output (Adjustable from 20 to 30V) Available between output + and - Regulation : < 15mV for a load variation from 0 to 100% < 2mV for a line variation from 198 to 264V Ondulation : < 3mV rms including: < 5mV peak to peak of the switching signal < 8mV peak to peak of the signal at 100Hz < 25mV peak to peak of switching spikes Indicators Green power-on LED indicator. Overheat or overcurent red LED "status" indicator. +15V (alone) I max : 5,5A on the short-circuit 5A from 10 to 12V 4A at 15V -15V (alone) I max : 2,1A in short-circuit condition 2A from 10 to 15V 24V (Adjustable from 20 to 30V) I max : 2,1A at the short circuit 2A from 20 to 30V Power Max output power : 60W. I max ±15V : 2A s Against short-circuits by current limit. Against overcurrent on source by fuse. Overtemperature protection by thermal circuit-breaker : Class II, Safety Extra Low Voltage (SELV) Complies with EN , overvoltage category II, pollution degree 2. EMC : Complies with EN , performance criteria B, and level : IP30. Operating temperature : 5 to 40 C Input voltage : 198 to 264 V, 50 / 60 Hz. Mains input : C8 socket with CEI320 C7 removable cable (2 poles double insulation). Power consumption : 78W max. ON/OFF control : toggle switch Dielectric strength : 3000 V between input to output. Presentation : polycarbonate case screenprinted. 31

Sorensen XG 1700 Series 1700 W A Watt, 1U Programmable DC Power Supplies V. Key Features. Key Modes

Sorensen XG 1700 Series 1700 W A Watt, 1U Programmable DC Power Supplies V. Key Features. Key Modes Sorensen XG 1700 Series 1700 W 1700 Watt, 1U Programmable DC Power Supplies 6 600 V Industry Leading Power Density Up to 1700 Watts in 1U Standard Digital Interfaces USB&RS232/485 LXI Ethernet and Isolated

More information

& HIGH CURRENT DC POWER SUPPLIES INSTRUCTION MANUAL

& HIGH CURRENT DC POWER SUPPLIES INSTRUCTION MANUAL 72-6850 & 72-6852 HIGH CURRENT DC POWER SUPPLIES INSTRUCTION MANUAL Table of Contents Introduction 2 Specification 2 Safety 4 EMC 5 Installation 6 Connections 6 Operation 7 Maintenance and Repair 8 www.tenma.com

More information

Sorensen XG Series / XTR Series W A. 850 W, 1U Half Rack Programmable DC Power Supplies V

Sorensen XG Series / XTR Series W A. 850 W, 1U Half Rack Programmable DC Power Supplies V Sorensen XG Series / XTR Series 670 850 W 850 W, 1U Half Rack Programmable DC Power Supplies 6 600 V Highest Power Density Comprehensive Digital and Analog Interface Options Scalable, Multi-Unit Design

More information

The 3 kw Models will accept 200*/230 VAC single phase and 200*/208 VAC three phase input power.

The 3 kw Models will accept 200*/230 VAC single phase and 200*/208 VAC three phase input power. Sorensen DLM 3 & 4 kw Series DC Power Supply High Power Density : 3 kw and 4 kw models, 2U (3½ high), (19 wide); no top or bottom clearance spacing required Preview Push-button : Overvoltage protection

More information

EPS/ELA-Series User Manual EPS/ELA 250W

EPS/ELA-Series User Manual EPS/ELA 250W EPS/ELA-Series User Manual EPS/ELA 250W EPS Stromversorgung GmbH Tel: +49 (0)821 570451 0 Index 3 Page: 1 Table of contents: Page 1. Features of ELA-Series... 3 1.1 Basic Functions... 3 1.2 Options...

More information

PROGRAMMABLE DC POWER SUPPLY MODEL 62000P SERIES

PROGRAMMABLE DC POWER SUPPLY MODEL 62000P SERIES MODEL 62000P PROGRAMMABLE DC POWER SUPPLY MODEL 62000P SERIES : 0 ~ 600V ; : 0 ~ 120A ; : 600W, 1200W, 2400W, 5000W 0.95 / / : (5ms~99hours) 10 100 / / 8 bit TTL 5V APG (Analog Programmable Interface)

More information

DUAL 60V 20A POWER FLEX POWER SUPPLY INSTRUCTION MANUAL

DUAL 60V 20A POWER FLEX POWER SUPPLY INSTRUCTION MANUAL 72-7570 DUAL 60V 20A POWER FLEX POWER SUPPLY INSTRUCTION MANUAL Table of Contents Specification 1 Safety 3 EMC 4 Installation 5 Connections 5 Operation 6 Maintenance 8 Specification General specifications

More information

BENCHTOP INSTRUMENT. Single Channel DC Power Supply SL Series Operation Manual V1.0

BENCHTOP INSTRUMENT. Single Channel DC Power Supply SL Series Operation Manual V1.0 BENCHTOP INSTRUMENT Single Channel DC Power Supply SL Series Operation Manual V1.0 CONTENTS 1. INTRODUCTION... - 1-2. PRODUCTION MODELS... - 1-3. SPECIFICATIONS... - 2-4. PANEL CONTROLS AND INDICATORS...

More information

DC POWER SUPPLY ALIMENTATION C.C.

DC POWER SUPPLY ALIMENTATION C.C. DC POWER SUPPLY ALIMENTATION C.C. ISO-TECH IPS 303A 201-3424 ISO-TECH IPS 601A 201-3446 SAFETY TERMS AND SYMBOLS These terms may appear in this manual or on the product: WARNING. Warning statements identify

More information

90W DC Power Supply. User Manual. 99 Washington Street Melrose, MA Phone Toll Free

90W DC Power Supply. User Manual. 99 Washington Street Melrose, MA Phone Toll Free 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com 1410 90W DC Power Supply User Manual Safety Summary The following safety precautions

More information

ISO-TECH IPS1810H and IPS1603D DC power supply ISO-TECH IPS 1810H et IPS 1603D Alimentation électrique c.c.

ISO-TECH IPS1810H and IPS1603D DC power supply ISO-TECH IPS 1810H et IPS 1603D Alimentation électrique c.c. ISO-TECH IPS1810H and IPS1603D DC power supply ISO-TECH IPS 1810H et IPS 1603D Alimentation électrique c.c. ISO-TECH IPS 1810H 204-713 ISO-TECH IPS 1603D 204-729 82IP-1810HME Ei Statement of Compliance

More information

DC REGULATED POWER SUPPLY

DC REGULATED POWER SUPPLY INSTRUCTION MANUAL Models 1620A/ 1621A/ 1622A/ 1623A/ 1626A/ 1627A DC REGULATED POWER SUPPLY Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com TABLE OF CONTENTS

More information

BENCHTOP INSTRUMENT. Multi-channel DC Power Supply TP2000N/TP2000PU/TP4000N Series Operation Manual V1.0

BENCHTOP INSTRUMENT. Multi-channel DC Power Supply TP2000N/TP2000PU/TP4000N Series Operation Manual V1.0 BENCHTOP INSTRUMENT Multi-channel DC Power Supply TP2000N/TP2000PU/TP4000N Series Operation Manual V1.0 CONTENTS 1. INTRODUCTION... - 1-2. PRODUCTION MODELS... - 2-3. SPECIFICATIONS... - 3-4. PANEL CONTROLS

More information

SSP-7080 USER MANUAL. 80W Constant Power Switching Mode Power Supply with Master & Slave Remote Sensing. Rev /

SSP-7080 USER MANUAL. 80W Constant Power Switching Mode Power Supply with Master & Slave Remote Sensing. Rev / SSP-7080 80W Constant Power Switching Mode Power Supply with Master & Slave Remote Sensing USER MANUAL Rev.1.1 2007/04 7673-7080-0000 CONTENTS Warning, Cautions and Operating Conditions P.1 Introduction

More information

Variable Regulated Voltage Power Supply Instruction Manual Model XP-605 / XP-752A

Variable Regulated Voltage Power Supply Instruction Manual Model XP-605 / XP-752A Variable Regulated Voltage Power Supply Instruction Manual Model XP-605 / XP-752A Copyright Elenco Electronics, Inc. REV-D DC POWER SUPPLY 1 2 4 5 CURRENT VOLTAGE 13 3 6 C.C. C.V. 7 FINE COARSE FINE COARSE

More information

DC REGULATED POWER SUPPLY

DC REGULATED POWER SUPPLY INSTRUCTION MANUAL Models 1620A/ 1621A/ 1622A/ 1623A/ 1626A/ 1627A MANUAL DE INSTRUCCIONES DC REGULATED POWER SUPPLY TABLE OF CONTENTS 1. INTRODUCTION... 3 2. FEATURES... 3 3. SPECIFICATIONS... 4 4. PRCAUTIONS

More information

Digital-Control and Programmable DC Power Supply Models: , , , & User Manual

Digital-Control and Programmable DC Power Supply Models: , , , & User Manual Digital-Control and Programmable DC Power Supply Models: 72-2535, 72-2540, 72-2545, 72-2550 & 72-10480 User Manual Page 19/05/16 V1.0 Safety Symbols This chapter contains important safety instructions

More information

3000 Series Operation Manual

3000 Series Operation Manual Operation Manual Copyright Copyright 1995 by this company. All rights reserved. No part of this publication may be reproduced in any form or by any means without the written permission of this company.

More information

99 Washington Street Melrose, MA Fax TestEquipmentDepot.com. Instruction Manual. Model 1672 Triple Output Power Supply

99 Washington Street Melrose, MA Fax TestEquipmentDepot.com. Instruction Manual. Model 1672 Triple Output Power Supply 99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com Instruction Manual Model 1672 Triple Output Power Supply Contents Section Description Page No. CONTENTS 1 1 TEST INSTRUMENT

More information

Powerful Solutions DHP - Introduction

Powerful Solutions DHP - Introduction Powerful Solutions DHP - ntroduction DHP - DC High Power Programmable Supply he DHP Family contains over 140 Tmodels ranging in output power from 2 kw to 30 kw in a single chassis. The 2 kw and 3 kw models

More information

Low and High Voltage Power Supplies

Low and High Voltage Power Supplies Low and High Voltage Power Supplies We work according to ISO 9001: 2008 Since 1994 Fug works according to the quality assurance system ISO 9001. All shipped units are checked and documented in our testing

More information

Ordering Information. Switching Power Supply S82F. Industrial-Grade Power Supply for General or Peak Load Applications SWITCHING POWER SUPPLIES

Ordering Information. Switching Power Supply S82F. Industrial-Grade Power Supply for General or Peak Load Applications SWITCHING POWER SUPPLIES Switching Power Supply S82F Industrial-Grade Power Supply for General or Peak Load Applications Correct input voltage range is automatically selected: 1 VAC or 2 VAC. Model S82F-P is suitable for peak

More information

Technical Specifications. Sentinel PRO 700 VA up to 3000 VA 1000 VA ER-2200 VA ER-3300 VA ER

Technical Specifications. Sentinel PRO 700 VA up to 3000 VA 1000 VA ER-2200 VA ER-3300 VA ER Technical Specifications Sentinel PRO 700 VA up to 3000 VA 1000 VA ER-2200 VA ER-3300 VA ER Sentinel PRO CONTENTS 1. GENERAL DESCRIPTION... 2 1.1. Main features of the UPS unit... 3 1.2. Standard Versions...

More information

LDX-U20 is a microprocessor controlled DC-UPS rated 20 A usable in 12 V or 24 V systems.

LDX-U20 is a microprocessor controlled DC-UPS rated 20 A usable in 12 V or 24 V systems. LDX-U20 is a microprocessor controlled DC-UPS rated 20 A usable in 12 V or 24 V systems. LDX-U20 monitors the voltage supplied by a DC source and in case of power failure a backup battery is connected

More information

SECTION DC POWER SUPPLY/BATTERY CHARGER

SECTION DC POWER SUPPLY/BATTERY CHARGER SECTION 26 33 05 PART 1 - GENERAL 1.1 THE REQUIREMENT A. The CONTRACTOR shall provide the single-phase heavy-duty industrial battery charger and all accessories required, complete and operable, in accordance

More information

KEPCO Will Point You In The Right Direction!

KEPCO Will Point You In The Right Direction! Looking For A High Power, Low Profile Power Supply? KEPCO Will Point You In The Right Direction! -9 AN ISO 900 COMPANY You'll Always Find What You Need At Kepco KLN Series Programmable Power Supply: 0W

More information

CIRCUIT-TEST OPERATION MANUAL. Switching Mode Power Supply with Remote Sensing PSC V 5A / 0-27V 3A / 0-36V 2.2A (80W)

CIRCUIT-TEST OPERATION MANUAL. Switching Mode Power Supply with Remote Sensing PSC V 5A / 0-27V 3A / 0-36V 2.2A (80W) CIRCUIT-TEST Switching Mode Power Supply with Remote Sensing PSC-9800 0-16V 5A / 0-27V 3A / 0-36V 2.2A (80W) OPERATION MANUAL 1 2 PSC-9800 08R14 Contents Safety Precautions...page 4 Introduction... 5 Controls

More information

HT3003PB HT3005PB MULTI-OUTPUT DC REGULATED POWER SUPPLY

HT3003PB HT3005PB MULTI-OUTPUT DC REGULATED POWER SUPPLY HT3003PB HT3005PB MULTI-OUTPUT DC REGULATED POWER SUPPLY This series include two-way and three-way DC regulated power supply. Three-way have high accuracy output of which two way are adjustable and one

More information

DC POWER SUPPLY (Switching mode)

DC POWER SUPPLY (Switching mode) DC POWER SUPPLY (Switching mode) ISO-TECH IPS1820D RS Stock No. 357-0760 ISO-TECH IPS3610D RS Stock No. 357-0776 ISO-TECH IPS606D RS Stock No. 357-0782 82IP-3610DMB Ei SAFETY TERMS AND SYMBOLS These terms

More information

OPERATING AND MAINTENANCE MANUAL. Primary Current Injection Test Set. 750ADM-H mk2

OPERATING AND MAINTENANCE MANUAL. Primary Current Injection Test Set. 750ADM-H mk2 OPERATING AND MAINTENANCE MANUAL Product: Type: Primary Current Injection Test Set 750ADM mk2 750ADM-H mk2 DESIGNED AND MANUFACTURED BY: T & R Test Equipment Limited 15-16 Woodbridge Meadows, Guildford,

More information

Phoenix Inverter

Phoenix Inverter Manual EN Handleiding NL Manuel FR Anleitung DE Manual ES Appendix Phoenix Inverter 12 250 12 375 12 500 12 800 24 250 24 375 24 500 24 800 48 250 48 375 48 500 48 800 1. Safety instructions WARNING: ELECTRIC

More information

Switching DC Power Supply

Switching DC Power Supply 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Model 1693, 1694 Switching DC Power Supply INSTRUCTION MANUAL 1 Safety Summary

More information

B BASIC HEAT TREATMENT CONSOLE

B BASIC HEAT TREATMENT CONSOLE Maritime Stress PO Box 2898, 30 Estates Road Dartmouth, NS, B2W 4Y2, Canada Toll Free: 1-877-468-1781 Phone: (902) 468-7873 Fax: (902) 468-2304 Website: E-mail: info@maritimestress.com OPERATION MANUAL

More information

BBC-3140 USER MANUAL DC-DC CHARGER / BATTERY EQUALIZER / VOLTAGE REDUCER

BBC-3140 USER MANUAL DC-DC CHARGER / BATTERY EQUALIZER / VOLTAGE REDUCER BBC-3140 USER MANUAL DC-DC CHARGER / BATTERY EQUALIZER / VOLTAGE REDUCER Important The BBC -3140 must be used according to the local safety standards with the particular application. All wiring and connections

More information

Low Profile DC Power Supply with Zero Voltage Soft Switching

Low Profile DC Power Supply with Zero Voltage Soft Switching Sorensen XFR Series Low Profile DC Power Supply with Zero Voltage Soft Switching Analog programming Zero voltage soft switching Constant voltage or constant current operation with automatic crossover and

More information

2.1 Warnings & Agency Approvals Electrical Connections - Specifications Standard Wiring Configurations...2 4

2.1 Warnings & Agency Approvals Electrical Connections - Specifications Standard Wiring Configurations...2 4 CHAPTER ELECTRICAL 2 INSTALLATION Contents of this Chapter... 2.1 Warnings & Agency Approvals..................2 2 2.1.1 Isolation..............................................2 2 2.1.2 Electrical Power

More information

Switching Power Supply

Switching Power Supply Switching Power Supply Easy-to-use Industrial Power Supply with Versatile Functions (); Power Supply Suitable for Peak Loads such as Motors and Solenoids (-P) Remote control function incorporated. Remote

More information

Technical Datasheet. Compact DC Energy Meter. Multi-Function DC Energy Meter

Technical Datasheet. Compact DC Energy Meter. Multi-Function DC Energy Meter Preliminary Datasheet Technical Datasheet Compact DC Energy Meter RISH EM DC series is specially designed to measure, display and communicate DC Voltage, Current, Power and Energy to monitor and control

More information

World Class Power Solutions. Rectifiers. For Stationary Battery Systems in Nuclear Power Plants

World Class Power Solutions. Rectifiers. For Stationary Battery Systems in Nuclear Power Plants World Class Power Solutions Rectifiers For Stationary Battery Systems in Nuclear Power Plants General 2 1.1 Application Electronically controlled rectifier assemblies are used in conjunction with suitable

More information

VSD Series II Variable Speed Micro Drives

VSD Series II Variable Speed Micro Drives VSD Series II Variable Speed Micro Drives Product Bulletin Code No. LIT-12011813 Issued March 26, 2013 Refer to the QuickLIT website for the most up-to-date version of this document. Johnson Controls VSD

More information

SECTION MICROPROCESSOR TRIP UNITS FOR LV CIRCUIT BREAKERS. This section is organized as indicated below. Select desired Paragraphs.

SECTION MICROPROCESSOR TRIP UNITS FOR LV CIRCUIT BREAKERS. This section is organized as indicated below. Select desired Paragraphs. SECTION 16904 MICROPROCESSOR TRIP UNITS FOR LV CIRCUIT BREAKERS PART 2 PRODUCTS 01 MANUFACTURERS A. B. C. Eaton * * The listing of specific manufacturers above does not imply acceptance of their products

More information

INSTRUCTION MANUAL Model 1743B

INSTRUCTION MANUAL Model 1743B Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com INSTRUCTION MANUAL Model 1743B 0-35 V, 0-6 A DC POWER SUPPLY With Dual 4-Digit LED Displays TEST INSTRUMENT

More information

SPECIFICATIONS UPS Triple Output 13.6VDC/213W, 48VDC/153W, 48VDC/39W

SPECIFICATIONS UPS Triple Output 13.6VDC/213W, 48VDC/153W, 48VDC/39W Page 1 / 7 Full operation without need of battery Two independent 48Vdc outputs for switching and control Local monitoring with 8 LEDs Remote monitoring with 4 alarm relays Monitoring and configuration

More information

PRODUCTS: POWER SUPPLY

PRODUCTS: POWER SUPPLY PRODUCTS: POWER SUPPLY Impact Lighting Inc. All rights reserved. Impact Lighting Inc. Reserves the right to change specifications without notice. 138 POWER SUPPLY 15W AC-DC [12V/1.25A] UNIVERSAL POWER

More information

TECHNICAL DESCRIPTION

TECHNICAL DESCRIPTION Electrical Energy Storage Tester EEST-511-S Semi-Automatic Charge-Discharge Battery Bench 1 channel 50 V / 100A (Ni-CD, Pb, Ni-Mh, Li-ion...) TECHNICAL DESCRIPTION To buy, sell, rent or trade-in this product

More information

Equipment model: auxiliary control. Pack Cat.Nos 10/16 A V± P + T shuttered module module

Equipment model: auxiliary control. Pack Cat.Nos 10/16 A V± P + T shuttered module module transformers and buzzers and bells socket outlets and special supports 042 25 042 52 041 07 042 80 042 85 Pack Cat.Nos Bell transformers dconform to IEC / EN 61558-2-8 Protected against overloads and short

More information

Technical Specification SENTINEL PRO

Technical Specification SENTINEL PRO Technical Specification SENTINEL PRO Contents 1 GENERAL DESCRIPTION... 3 1.1 Main features of the UPS unit... 4 1.2 Standard Versions... 4 1.3 ER Versions for extended autonomy... 4 2 SENTINEL PRO SERIES

More information

Triple Output Power Supply

Triple Output Power Supply Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com Model 1672, 1673 Triple Output Power Supply INSTRUCTION MANUAL 1 Safety Summary The following safety precautions

More information

Control Power V AC, 50/60 Hz 150-C30NBD 150-C30FHD

Control Power V AC, 50/60 Hz 150-C30NBD 150-C30FHD Bulletin Product Selection Open Type and Non-Combination Enclosed (IP, NEMA /) Controllers For use with Line-Connected Motors Rated Voltage [V AC] / Motor Current [A]...... Max. kw, Hz Max. Hp, Hz Control

More information

BLU SERIES Battery Load Units

BLU SERIES Battery Load Units BLU SERIES Battery Load Units Lightweight starting from 12,8 kg (28.2 lbs) Powerful discharge power of up to 28,4 kw Voltage measurement range: 5,25-500 V DC Discharge current up to 340 A DC Easily expandable

More information

LAVOLTA DC REGULATED POWER SUPPLY BPS-305

LAVOLTA DC REGULATED POWER SUPPLY BPS-305 LAVOLTA DC REGULATED POWER SUPPLY BPS-305 USER MANUAL 1 In order to use the power supply better, please read the user manual carefully before using and keeping it properly. Warning: Do not connect any

More information

DC POWER SUPPLY SYSTEMS

DC POWER SUPPLY SYSTEMS DC POWER SUPPLY SYSTEMS double branch Rectifier - SCR type TITANIUM 2R-SCR PLUS SERIES TITANIUM 2R-SCR rectifier series belongs to the Double Branch category thus provided with two independent AC / DC

More information

Burden Fuse Rating Resistor SAF / SAK6 1NM 10mm M8 12NM SAF / SAK10 2NM 16mm M8 12NM

Burden Fuse Rating Resistor SAF / SAK6 1NM 10mm M8 12NM SAF / SAK10 2NM 16mm M8 12NM Contents Section Page 1.0 Introduction 1 2.0 Specification 1-4 3.0 Installation 5-8 4.0 Programming 9-10 5.0 Menus 10-12 6.0 Fault Finding/Diagnostics 12-13 7.0 Communication 13 8.0 Setting Up 13-16 1.0

More information

LV Capacitor Bank APC

LV Capacitor Bank APC LV Capacitor Bank APC The ABB comprehensive solution for automatic power factor correction: APC standard, reinforced and de-tuned automatic capacitor banks The ABB comprehensive solution for automatic

More information

Safety Precautions. Damages resulting from failure to observe these safety precautions are exempt from any legal claims whatever.

Safety Precautions. Damages resulting from failure to observe these safety precautions are exempt from any legal claims whatever. Safety Precautions This product complies with the requirements of the following European Community Directives: 2004/108/EC (Electromagnetic Compatibility) and 2006/95/EC (Low Voltage) as amended by 2004/22/EC

More information

150 B180 N B D A 8L. Enclosure Type. Input Line Voltage Open Type V AC, 3-phase, 50 and 60 Hz V AC, 3-phase, 50 and 60 Hz

150 B180 N B D A 8L. Enclosure Type. Input Line Voltage Open Type V AC, 3-phase, 50 and 60 Hz V AC, 3-phase, 50 and 60 Hz Catalog Number Explanation Open Controllers a Bulletin Number Solid-State Controller B H H B B B B B B B B B B B B B Solid-State Controller and Isolation Contactor (enclosed only) b Controller Ratings

More information

Power Conversion Systems 2005/2006. Schaefer the Power to make it happen.

Power Conversion Systems 2005/2006. Schaefer the Power to make it happen. Power Conversion Systems 2005/2006 Schaefer the Power to make it happen. Company profile workforce experience customer orientation flexibility reliability Schaefer Elektronik, founded in 1969, has grown

More information

Industrial Chargers and

Industrial Chargers and Industrial Chargers and DC Systems SPR - Single Phase Rectifier TPR - Three Phase Rectifier 12V 250V 5A 1000A Designed for all Industrial applications Oil & Gas, Petrochemicals Offshore, Onshore, Pipelines

More information

USER MANUAL. IPS home inverters with UPS function. IPS home inverter manual

USER MANUAL. IPS home inverters with UPS function. IPS home inverter manual USER MANUAL IPS home inverters with UPS function Suitable for UPS: - IPS300-SIN - IPS300-SIN-WM - IPS300-SIN-DC - IPS600-SIN - IPS600-SIN-WM - IPS600-SIN-DC - IPS1000-SIN - IPS1000-SIN-DC - IPS1600-SIN

More information

CI-tronic Soft Start Motor Controller Type MCI 25B with Brake

CI-tronic Soft Start Motor Controller Type MCI 25B with Brake Data sheet CI-tronic Soft Start Motor Controller Type MCI 25B with Brake MCI 25B motor controller with brake is designed for soft starting and braking of 3 phase AC motors. The digital controlled soft

More information

LV Capacitor Bank APC

LV Capacitor Bank APC LV Capacitor Bank APC The ABB comprehensive solution for automatic power factor correction: APC standard, reinforced and de-tuned automatic capacitor banks The ABB comprehensive solution for automatic

More information

SST-ST75F-ESS The essential silver standard

SST-ST75F-ESS The essential silver standard STRIDER ESSENTIAL SERIES SST-ST75F-ESS The essential silver standard High efficiency with 80 PLUS Silver certification 24/7 continuous power output with 40 operating temperature Class-leading single +12V

More information

10 20KVA 3Ph/1Ph KVA 3Ph / 3Ph

10 20KVA 3Ph/1Ph KVA 3Ph / 3Ph VEGA INDUSTRIAL UNINTERRUPTIBLE POWER SUPPLY 10 20KVA 3Ph/1Ph 10 120KVA 3Ph / 3Ph - 6 pulse SCR rectifier - IGBT inverter - Power output transformer - Low and stable ripple on battery for the highest battery

More information

Models. Output current max.* Output Power max. Low Line : VAC High Line: VAC 24 VDC / 12 A 240 W. Back up battery

Models. Output current max.* Output Power max. Low Line : VAC High Line: VAC 24 VDC / 12 A 240 W. Back up battery AC/DC Battery Controller Power Supply TSPC-240UPS Series Compact universal 24 VDC power supply with integrated battery controller module Battery protection for over voltage, deep discharge, short circuit

More information

The Complete System Solution! Highest Grade Electronic Components RoHS Compliant.

The Complete System Solution! Highest Grade Electronic Components RoHS Compliant. Advantages of the 72 Alternating Relay The Complete System Solution! Highest Grade Electronic Components RoHS Compliant. The Model 72 series Alternating Relay is designed for duplex pumping systems where

More information

Induction Power Supplies

Induction Power Supplies Induction Power Supplies 7.5kW; 135 400kHz 480V version (Integral Heat Station) User s Guide Model 7.5-135/400-3-480 SMD Control Brds Rev. D 5/08 Table of Contents 1. Specifications and features...3 2.

More information

Remote on/off switch Connector for remote on/off switch available on all models. DIP switch for 50/60Hz selection (48/350 model only)

Remote on/off switch Connector for remote on/off switch available on all models. DIP switch for 50/60Hz selection (48/350 model only) SinusMax Superior engineering Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave

More information

IRT 4000 AT-S/M/L. Technical Manual. quality IN MOTION. quality IN MOTION

IRT 4000 AT-S/M/L. Technical Manual. quality IN MOTION.   quality IN MOTION IRT quality IN MOTION www.irtsa.com 4000 AT-S/M/L Technical Manual IRT quality IN MOTION E2 0 8 4 1 5 September 2013-Rev. 5 UL Requirements Drives Series 2000 / 4000 AT 1. Field wiring terminal to use

More information

1 Phase electronic contactor (SC 1)

1 Phase electronic contactor (SC 1) 1 Phase electronic contactor (SC 1) - Rated operational voltage up to 600VAC 50/60 Hz - Rated operational current up to 15/30A/50/63A AC-1 - Control voltage from or - Compact modular design 22.5, 45, or

More information

Alpha EM DC Multi-Function DC Energy Meter. Technical Datasheet. Compact DC Energy Meter

Alpha EM DC Multi-Function DC Energy Meter. Technical Datasheet. Compact DC Energy Meter Alpha EM DC Technical Datasheet Compact DC Energy Meter ALPHA EM DC series is specially designed to measure, display and communicate DC Voltage, Current, Power and Energy to monitor and control the target

More information

MCD 200 Series Soft Starters

MCD 200 Series Soft Starters MCD 200 Series Soft Starters AC motors often cause one or more serious problems during startup acceleration. MCD 200 Series electronic soft starters control motor current to provide a smooth start. When

More information

TECHNICAL DATA SHEET KVA UPS Systemss

TECHNICAL DATA SHEET KVA UPS Systemss Återförsäljare: Tre Röda AB TillingeHagby 7-745 94 ENKÖPING Tel: 08-560 200 22 e-post: info@treroda.nu http: www.treroda.nu When the INSIDE is important make the OUTSIDE Cannon TECHNICAL DATA SHEET 400-500-600-800

More information

Technical brochure. The Vector series The ABB comprehensive solution for automatic power factor correction

Technical brochure. The Vector series The ABB comprehensive solution for automatic power factor correction Technical brochure The Vector series The ABB comprehensive solution for automatic power factor correction 2 Applications The Vector series The Vector series The Vector series is a powerful and compact

More information

SINAMICS GM150 IGCT version

SINAMICS GM150 IGCT version /2 Overview /2 Benefits /2 Design /6 Function /8 Selection and ordering data /8 Options Technical data /14 General technical data /15 Control properties /15 Ambient conditions /16 Installation conditions

More information

ELECTRICAL PANELS. Chap.

ELECTRICAL PANELS. Chap. ELECTRICAL PANELS 360 Panel System Electrical Panels 360 Panel System Modular Panels DC Electric Panels AC Electric Panels AC/DC Electric Panels Aber Marine Panels IP 67 Watertight Panels Rotary Switch

More information

150 WATT HEW SINGLE SERIES DC/DC CONVERTERS

150 WATT HEW SINGLE SERIES DC/DC CONVERTERS Features Description The 4:1 Input Voltage 150 W single HEW Series of DC/DC converters provide precisely regulated dc outputs. The output voltage is fully isolated from the input, allowing the output to

More information

Emergency lighting units EM powerled

Emergency lighting units EM powerled BASIC FX SR 50 W Combined emergency lighting LED Driver Product description Independent fixed output LED Driver for mains operation with integrated Simple CORRIDOR FUNCTION (CF) Emergency lighting function

More information

MJÖLNER 200 Microhmmeter

MJÖLNER 200 Microhmmeter Fully automatic testing Micro processor controlled Safe test DualGround and Remote control True DC ripple free current Lightweight suitcase withstands the impact of water, dust or sand Built in thermal

More information

Electronic Ballast EVG 2000-T

Electronic Ballast EVG 2000-T Electronic Ballast EVG 2000-T Operating Manual Table of contents 1 Description 1.1 Advantages of this ballast... 3 1.2 Functional principle... 3 1.3 Energization... 4 1.4 Visualization... 5 1.5 Indications

More information

Power Switching Devices

Power Switching Devices Watlow has manufactured solid state power controllers for over forty years. Watlow s is a microprocessor-based product that features application flexibility unmatched by any other silicon controlled rectifier

More information

The Z Series. SCR Power controllers for resistance heating applications. Zero-Fired SCR Power Controllers AMPS VAC

The Z Series. SCR Power controllers for resistance heating applications. Zero-Fired SCR Power Controllers AMPS VAC The Z Series Zero-Fired SCR Power Controllers 60-1200 AMPS 120-600 VAC SCR Power controllers for resistance heating applications. ROBICON 1996 Rev. 7/96 Applications Robicon s Z series power controls are

More information

Open Frame Power Supplies

Open Frame Power Supplies , 0 300 Watt Features Small and compact PCB Construction Optional with Chassis and Cover Universal Input 8 264 VAC, Output Voltage adjustable Compliance to E 6000-3-2 (PFC) EMI meets E022, Class B and

More information

J1000. Compact Inverter Series.

J1000. Compact Inverter Series. J1000 Compact Inverter Series www.yaskawa.eu.com Focus on Application Customer orientation and application focus two attributes of machine equipment YASKAWA offers with its J1000 compact inverter drive

More information

Product Guide AC Voltage Control Devices. Guide Guide. Popular Variable Transformers and AC Power Supplies.

Product Guide AC Voltage Control Devices. Guide Guide. Popular Variable Transformers and AC Power Supplies. Popular Variable Transformers and AC Power Supplies Product Guide AC Voltage Control Devices Guide Guide Your Tailored Power Solutions Provider TM Staco Energy Products Co. has been a leading manufacturer

More information

BC-2014 ULTRA COMPACT 4-BAY SMART BATTERY CHARGER (Military Grade)

BC-2014 ULTRA COMPACT 4-BAY SMART BATTERY CHARGER (Military Grade) BC-2014 ULTRA COMPACT 4-BAY SMART BATTERY CHARGER (Military Grade) Especially suitable for Naval use, 19 Rack Type, with IP- 67 protection class. Made to H: 125 mm W: 275 mm D: 250 mm Up to 4 batteries

More information

Technical Data Sheets

Technical Data Sheets GE Consumer & Industrial Technical Data Sheets Digital Energy Uninterruptible Power Supply SG-CE Series 160 200 250 300 kva PurePulse TM 400 Vac CE Series 1 Date of issue: 15.02.2007 SGSE160-200S1UPS01

More information

TC-500PD8. Switching Power Supply ( PS2 A T X 500W 8 0+ ) SPECIFICATION. Revision: 2.0

TC-500PD8. Switching Power Supply ( PS2 A T X 500W 8 0+ ) SPECIFICATION. Revision: 2.0 TC-500PD8 TC-500PD8 Switching Power Supply ( PS2 A T X 500W 8 0+ ) SPECIFICATION Revision: 2.0 727,. Phillips Drive City of Industry. CA 91748. USA http:// www.xeal.com.tw TEL: 626-303-8885 FAX: 626-301-0588

More information

BLU SERIES Battery Load Units

BLU SERIES Battery Load Units BLU SERIES Battery Load Units Lightweight starting from 12,8 kg (28.2 lbs) Powerful discharge power of up to 28,4 kw Voltage measurement range: 5,25-500 V DC Discharge current up to 340 A DC Easily expandable

More information

EM DC Multi-Function DC Energy Meter

EM DC Multi-Function DC Energy Meter Analogue Meters With Moving - Iron Movement EM DC Compact DC Energy Meter Ziegler EM DC series is specially designed to measure, display and communicate DC Voltage, Current, Power and Energy to monitor

More information

SSW07. Soft Starters. Applications. Standard Features

SSW07. Soft Starters. Applications. Standard Features General Information CFW10 CFW100 CFW08 CFW500 CFW700 CFW701 CFW11 EDP11 CFW11M SSW05 SSW06 GPH2 TPH2 are static starting devices, designed for the acceleration, deceleration and protection of the three

More information

DEVICE STATE/BYPASSED FAILURE OVERLOAD

DEVICE STATE/BYPASSED FAILURE OVERLOAD Technical specifications Type 5. 7. Control electronics Rated values Terminal Rated control supply voltage A1A2 V AC 115 230 115 230 Tolerance % -15+10-15+10 Rated control supply STANDBY ma 15 15 Rated

More information

Switching Power Supplies

Switching Power Supplies Features Boxed Power Supplies with Screw Terminal Block Single- and Triple Output Models EMI Compliance with EN 55022 and FCC Part 15, Level B Short Cirquit Protection Overvoltage Protection High Efficiency

More information

Low voltage AC drives. ABB micro drives ACS to 3 hp/0.18 to 2.2 kw Catalog

Low voltage AC drives. ABB micro drives ACS to 3 hp/0.18 to 2.2 kw Catalog Low voltage AC drives ABB micro drives ACS55 0.25 to 3 hp/0.18 to 2.2 kw Catalog ACS55 IP20 Overview ACS55 micro drives are designed for use in a wide variety of simple machinery applications where only

More information