Vehicle Security / Remote Start / Remote Access System Installation
|
|
- Angelica Cunningham
- 1 years ago
- Views:
Transcription
1 MKC Vehicle Security/Remote Start/Remote Access Vehicle Security / Remote Start / Remote Access System Installation CONTENTS VSS Module Installation Security Indicator LED Mounting RMST Kit Antenna Installation RMU Module Installation GENERAL PROCEDURES Shock Sensor Sensitivity Adjustment RMU Activation Contents SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
2 MKC Vehicle Security/Remote Start/Remote Access 1 INSTALLATION Vehicle Security / Remote Start / Remote Access - MKC VSS System Components Security Indicator LED (19D596) "Optional" MKC 1. Verify correct kit number. Review VSS Kit Contents Kits are vehicle specific and are not interchangeable. 2. Review the VSS kit contents. Vehicle Security System (VSS) Kit QUANTITY DESCRIPTION 1 VSS Module 1 T-harness Page 1 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
3 MKC Vehicle Security/Remote Start/Remote Access 2 Vehicle Security System (VSS) Kit(Continued) 6 Tie-straps Security Indicator LED Kit Contents "Optional" 3. Review the Security Indicator LED kit contents. Security Indicator LED Kit 1 Owner's Manual QUANTITY I. VSS System Installation DESCRIPTION 1 Security Indicator LED CAUTION: Carefully route and secure module and harnesses so that they do not interfere with moving parts or linkages. If the VSS kit was installed previously and the vehicle is being upgraded, proceed to the "RMST" or "RMU" upgrade section(s). 4. If the vehicle is equipped with factory remote start, test its operation by pressing the Lock button one time and the Remote Start button two times. If the vehicle remote starts, stop the engine by pressing the Remote Start button one time. If the vehicle does not remote start, diagnose the concern. 5. Disconnect the vehicle battery negative terminal. For additional information, refer to Workshop Manual (WSM) Section Remove the LH lower Instrument Panel (IP) insulator. Page 2 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
4 MKC Vehicle Security/Remote Start/Remote Access 3 7. Disconnect the electrical connector from the back of the gateway module. 8. Connect the T-harness to the gateway module electrical connector. Page 3 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
5 MKC Vehicle Security/Remote Start/Remote Access 4 9. Connect T-harness to the back of the gateway module. 10. Position the T-harness inside the IP being careful to avoid sharp edges and moving parts. Secure with zip-ties. 11. Position the VSS module on the driver side of the vehicle and secure it to the hood release cable and adjacent wire harness. Ensure the VSS module is positioned so the shock sensor adjustment knob can be accessed for later use. Ensure the tie-strap is routed through the VSS module loops at opposite corners. Page 4 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
6 MKC Vehicle Security/Remote Start/Remote Access Connect the T-harness to the VSS module. Secure the VSS harness with tie-straps. 13. Connect the vehicle battery negative terminal. For additional information, refer to WSM Section Optional Security Indicator LED Mounting CAUTION: Carefully route and secure module and harnesses so that they do not interfere with moving parts or linkages. 14. Keep the following points in mind when routing or positioning the LED for mounting: Have at least 3/4" clearance behind trim panels for the wiring harness to be routed. The LED should be clearly visible from the driver's side window when mounted. Do not mount the LED on trim panels that cover air bags. 15. Mount the LED at an appropriate location on the upper steering column shroud, using the guidelines listed above. Drill a 9/32" hole into the selected location, for the LED to mount in. 16. Route the LED wire harness to the VSS module. Page 5 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
7 MKC Vehicle Security/Remote Start/Remote Access Connect the LED wire harness to the VSS module 2-pin white connector. Secure the LED wire harness with tie-straps. 18. If the vehicle is equipped with factory remote start, test its operation by pressing the Lock button one time and the Remote Start button two times. If the vehicle remote starts, stop the engine by pressing the Remote Start button one time. If the vehicle does not remote start, disconnect the vehicle battery negative terminal, wait five minutes and then reconnect the battery negative terminal. For additional information, refer to Workshop Manual (WSM) Section Retest the factory remote start. If the vehicle does not remote start, diagnose the concern. Shock Sensor Sensitivity Adjustment The VSS module is equipped with an internal dual zone Shock Sensor. The VSS system will activate a single horn honk/single light flash anytime a light to moderate impact is detected, and a "panic" type 30 second horn honk/light flash sequence when a heavy impact is detected while the VSS system is armed. Adjustment of both zones is accomplished through a single adjustment knob on the VSS module. Rotating the knob clockwise will increase sensitivity and rotating the knob counter-clockwise will decrease sensitivity. Sensitivity adjustment must be completed with the module securely mounted and the adjustment knob accessible. Page 6 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
8 MKC Vehicle Security/Remote Start/Remote Access Starting with the adjustment knob in approximately the halfway position, lower the driver's window and exit the vehicle. 20. Press the LOCK button on the vehicle's RKE fob to arm the VSS system. The LED will light solid for 20 seconds and then begin to flash a steady on/off sequence to indicate the system is armed. 21. Using a closed fist, impact the steering wheel with moderate force to simulate a light impact on the vehicle. If the impact is detected, the horn will honk and the lights will flash 1 time to indicate the warning impact was detected. 22. Using a closed fist, impact the steering wheel with heavy force to simulate a hard impact (i.e. glass breakage) on the vehicle. If the impact is detected, the horn will honk and the lights will flash a steady on off sequence to indicate the heavy or full shock trigger was detected. 23. Increase (rotate clockwise) or decrease (rotate counter-clockwise) the adjustment knob as necessary to achieve desired sensitivity, repeat the previous steps to test, and verify adjustment. VSS Functional Test If installed, observe the LED while performing these tests. 24. Lower the driver's door window, then close all doors, hood, and trunk/hatch and press lock on the keyfob. The LED should stay lit for 20 seconds while the VSS system pre-arms, after which it will flash every 3-4 seconds in fully armed mode. 25. Reach inside the window hit the door unlock trim switch. The LED should continue to flash, indicating that the vehicle is still armed. Use the inside driver's door handle to open the door. The alarm should sound, indicating perimeter breach. Turn the alarm off by turning the ignition to "On". If equipped with OE perimeter security, there will be a 12 second interior chime prior to alarm sounding. For vehicles not equipped with OE perimeter security, there will be a 12 second delay with no interior chime prior to alarm sounding. For push button start vehicles, the Intelligent Access (IA) key must be away from the vehicle, otherwise the security system may disarm immediately upon trigger. Page 7 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
9 MKC Vehicle Security/Remote Start/Remote Access Exit the vehicle and arm it again, this time leaving the driver's door open. The vehicle should arm itself, ignoring the open door but monitoring the rest. Once the vehicle is armed, shut the driver's door and reopen it after a few seconds. The alarm should sound. Turn the alarm off by hitting unlock on the keyfob. For push button start vehicles, the Intelligent Access (IA) key must be away from the vehicle, otherwise the security system may disarm immediately upon trigger. 27. Test all other vehicle doors, the hood and the trunk in the same manner, by setting off the alarm and disarming with the keyfob. 28. If the VSS kit will not be upgraded to RMST/RMU functions at this time, install the LH lower IP insulator. Please contact FORD-KEY with any issues regarding hardware or kit contents. II. Remote Start (RMST) Upgrade - Antenna Kit "Sold Separately" CAUTION: Carefully route and secure module and harnesses so that they do not interfere with moving parts or linkages. Page 8 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
10 MKC Vehicle Security/Remote Start/Remote Access 9 Standard Key Fob (15K601) "Sold Separately" Bi-directional Key Fob (15K601) "Sold Separately" Optional RMST Upgrade Components "Sold Separately" 29. Review the RMST Upgrade components. Remote Start (RMST) Upgrade - Antenna Kit "Sold Separately" QUANTITY DESCRIPTION 1 Bi-directional Antenna (15603) 1 Security Jumper (15603) Standard Key Fob (15K601) "Sold Separately" QUANTITY DESCRIPTION 1 Standard Key Fob (15K601) Page 9 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
11 MKC Vehicle Security/Remote Start/Remote Access 10 Bi-directional Key Fob (15K601) "Sold Separately" QUANTITY DESCRIPTION 1 Bi-directional Key Fob (15K601) RMST Kit Antenna Installation 30. If previously installed, remove the LH lower IP insulator. 31. Position the top portion of the LH kick panel aside to allow for removal of the IP side finish panel. 32. Remove the LH IP side finish panel. 33. Clean the antenna mounting surface using an alcohol base solution and a clean cloth. 34. Do not touch the adhesive, reduced adhesion may result. Make sure that the long wire on the antenna is pointing towards the top of the windshield since this wire will be routed along the headliner. The wire will be attached to the control module later in this procedure. Remove the protective backing from the adhesive on the antenna and firmly press the body of the antenna onto the mounting surface. Page 10 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
12 MKC Vehicle Security/Remote Start/Remote Access If necessary, position the A-pillar trim slightly outward to provide access to route the antenna wire. Do not route the antenna wire over the top of air bags. 36. Route the antenna cable along the headliner and down the A-pillar towards the floor. Continue routing the wire into the IP towards the VSS module. Secure with tie-straps. 37. Connect the antenna connector to the VSS module. 38. Reposition the A-pillar trim panel back, if necessary. 39. Install the LH IP side finish panel. Position the weatherstrip and LH kick panel back. VSS Module - Optional Vehicle Security Features 40. Enable/Disable Vehicle Security Features: Locate the security jumper supplied in the kit. Install the jumper to the VSS module if the vehicle security features are to be disabled. Not installing and/or removing the jumper from the VSS module will keep the vehicle security features enabled. Page 11 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
13 MKC Vehicle Security/Remote Start/Remote Access 12 Programming Key Fobs 41. These steps must be performed with the VSS module security jumper removed if previously installed. For additional information refer to "VSS Module - Optional Vehicle Security Features". The following steps must be performed with the driver door open. 1 Enter the vehicle with the vehicle key(s) and key fobs you wish to program. 2 Depress and hold brake pedal. 3 Press the start/stop button. 4 After the vehicle starts press the start/stop button to shut down. 5 Repeat steps 3 and 4 an additional four times, ending in ignition on, engine off. 6 Press the vehicle start/stop button twice to turn ignition on. The horn will honk 3 times to indicate transmitter learn mode access. 7 Press the start stop button on each fob you wish to program. 8 Cycle ignition to the OFF position to exit transmitter learn mode. 9 If the security jumper is installed the vehicle security features are disabled. If previously removed, reinstall the VSS module security jumper. For additional information, refer to "VSS Module - Optional Vehicle Security Features". Page 12 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
14 MKC Vehicle Security/Remote Start/Remote Access If the RMST kit will not be upgraded to RMU functions at this time, install the LH lower IP insulator. RMST Functional Test Do not put a key in the ignition for the following steps. 43. Make sure the shift lever is in PARK and the ignition is in the OFF position. Remove all keys from the vehicle. 44. Close the hood. 45. Close all of the vehicle doors. 46. Start the vehicle by pressing the remote start button twice on the remote start key fob. 47. Confirm the remote start works with the vehicle in park and with the hood and doors closed. 48. Open the hood. 49. Vehicle doors should be closed while performing this step. Confirm that the vehicle will not start with the hood open. Please contact FORD-KEY with any issues regarding hardware or kit contents. 50. See the Scalable Remote Start System Diagnosis Guide to resolve issues identified by the functional test. III. Remote Access (RMU) Upgrade "Sold Separately" 51. Review the RMU upgrade components. Optional Components Remote Access (RMU) Upgrade "Sold Separately" QUANTITY DESCRIPTION 1 Remote Messaging Unit (RMU) 1 SIM Card Carrier Page 13 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
15 MKC Vehicle Security/Remote Start/Remote Access 14 Optional Components Remote Access (RMU) Upgrade "Sold Separately"(Continued) 1 Security Jumper 52. If previously installed, remove the LH lower IP insulator. CAUTION: Carefully route and secure module and harnesses so that they do not interfere with moving parts or linkages. For proper range of operation, the RMU must be installed as shown in the diagram below. 53. Using tie-straps, secure the RMU to the previously installed VSS module. 54. Connect the RMU electrical connector to the VSS module. Secure the harness with tie-straps. Page 14 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
16 MKC Vehicle Security/Remote Start/Remote Access 15 VSS Module - Optional Vehicle Security Features 55. Enable/Disable Vehicle Security Features: Locate the security jumper supplied in the kit. Install the jumper to the VSS module if the vehicle security features are to be disabled. Not installing and/or removing the jumper from the VSS module will keep the vehicle security features enabled. 56. Install the LH lower IP insulator. RMU Activation Please note that the Remote Access application that is used to start the vehicle for this RMST kit will only work with iphone and Android phones. 57. For RMU activation the following information from the customer is recommended to provide them with electronic notification for app retrieval: 1 Address 2 Cell Phone Number 3 Cell Phone Carrier Company 58. Log on to your Professional Technician Society (PTS) account and enter the vehicle information. 1 Select "Vehicle Id". 2 Select "By Year & Model" 3 Choose the year & model of the vehicle and then select "GO". 4 Hover over the "Workshop" tab. 5 Select the "Accessory Installation" menu item. 6 Under the "Electrical" heading, select the "Remote Access Activation" link (first time users will need to agree to terms & conditions). 7 Select the "Install or Diagnose" link. Page 15 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
17 MKC Vehicle Security/Remote Start/Remote Access 16 If you are not directed to the screen shown below (or user agreement screen for first time users), make sure your internet browser zone settings are set to medium. This setting can be found in your browsers "internet options" under the "privacy" tab. 59. Once on the "Install" page, enter the SIM ID code that was provided with the RMST kit. Select "Begin or Continue Installation". Page 16 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
18 MKC Vehicle Security/Remote Start/Remote Access Click on the "On screen steps 1-6", and follow the on screen instructions to complete the installation. Page 17 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
19 MKC Vehicle Security/Remote Start/Remote Access 18 The following step will complete the activation process, when you are directed to a screen similar to the one below ensure the correct vehicle brand is selected and that all applicable features are enabled. The "perimeter" and "shock" settings below are optional features and should only be selected when security features are enabled. Page 18 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
20 MKC Vehicle Security/Remote Start/Remote Access Perform a functional check of the system by testing each of the available features. Start/Stop function Lock/Unlock function Car finder Signal (for troubleshooting only) All tests above must be completed in order to move to the next step. If any of the listed functions fail, move the vehicle to an outside location and retest. 62. Once the hardware installation and RMU activation process is complete, record the 4-digit PIN on the SIM card carrier. Provide the SIM card carrier to the customer so they can add this system to their Remote Access Account. Customer must have both the 4-digit PIN and SIM ID to activate/add their vehicle to their Remote Access Account. 63. If the customer agrees, you may push the mobile application to the customer. You will need the customer's phone number and cellular carrier. If the customer opts to install the application themselves, they can locate it in their mobile app store. Please contact FORD-KEY with any issues regarding hardware or kit contents. Page 19 of 19 SK9L2J-19G364-AA Copyright Ford 2016 FoMoCo
Remote Access System Installation
2013 Taurus Remote Access Remote Access System Installation CONTENTS VEHICLE PREPARATION Hood Switch Installation RMST Module Installation RMU Module Installation GENERAL PROCEDURES Remote Start Activation
LH POWER LOCK SYSTEMS 8P - 1 POWER LOCK SYSTEMS TABLE OF CONTENTS POWER DOOR LOCKS... 1 REMOTE KEYLESS ENTRY... 4 POWER DOOR LOCKS TABLE OF CONTENTS
LH POWER LOCK SYSTEMS 8P - 1 POWER LOCK SYSTEMS TABLE OF CONTENTS POWER DOOR LOCKS... 1 REMOTE KEYLESS ENTRY... 4 POWER DOOR LOCKS TABLE OF CONTENTS AND POWER DOOR LOCK SYSTEM...1 CENTRAL LOCKING SYSTEM...2
MM1 Installation Instructions
MM1 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or
TOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation
Section I Installation Preparation Part Number: 08586 47840 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 3 1 ECU Mounting Bracket Hardware Bag
READ ME FIRST. TECHNICAL SUPPORT FORD-KEY FRENCH TECHNICAL SUPPORT Rock Hebert (514)
READ ME FIRST TECHNICAL SUPPORT 1-800-FORD-KEY FRENCH TECHNICAL SUPPORT Rock Hebert (514) 973-2846 For convenience this document uses short names when referring to a particular system or kit. The list
CS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM
INTRODUCTION: CS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Remote Keyless Entry System by Crimestopper Security Products Inc.
User Guide 1 WAY FM MANUAL TRANSMISSION REMOTE STARTER. Table of Contents. Introduction
1 WAY FM MANUAL TRANSMISSION REMOTE STARTER User Guide Table of Contents... 1 Introduction... 1 Using the Remote Control... 2 Multi-Level Features (default state)... 2 Remote-Starting Your Vehicle... 3
Ford Accessory Vehicle Security, Keyless Entry and Remote Start Warranty Return Procedures DO NOT CLAIM PARTS WARRANTY ON FORM 1863 Parts Warranty Pro
READ ME FIRST TECHNICAL SUPPORT 1-800-FORD-KEY CANADIAN DEALERS BILINGUAL FRENCH/ENGLISH TECHNICAL SUPPORT (514)973-2846 For convenience this document uses short names when referring to a particular system
TOYOTA TACOMA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-35052 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 1 T-tap Connectors,
Vehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions
Model PRO 9842 Installation Manual Vehicle Alarm System With Channel 2 Auxiliary Output Installation Instructions This Unit Is Intended For Installation In Vehicles With 12 Volt Negative Ground Electrical
TOYOTA 4Runner Keyless Entry Upgrade Alarm
TOYOTA 4Runner 2013 - Keyless Entry Upgrade Alarm Part Number: 00016-32910 Accessory Code: QSNS10 Conflicts Note: NOT FOR INSTALLATION ON VEHICLES EQUIPPED WITH SMART KEY General Applicability Used on
TOYOTA TACOMA TVIP V5
Preparation Part Number: PT398-35090 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Security ECU 3 1 GBS ECU 4 1 Status Monitor/Microphone 5 2 Warning Labels (English) 6 2 Warning
INSTALLATION GUIDE. FCC ID NOTICE
REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This
Vehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED
100755-2 Installation Instructions PC 4200 PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
SCION xb 2004 SECURITY (V5) Section I Installation Preparation. Part Number:
Section I Installation Preparation Part Number: 08586 52960 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Mounting Bracket 3 1 GBS ECU 4 1 Security
AUTOMATIC TRANSMISSION ONLY! Technical Support: ext 1 Warning!!
REV.2006.04 INSTALL GUIDE AUTOMATIC TRANSMISSION ONLY! www.ultrastarters.com Technical Support: 877-598-2100 ext 1 support@ultrastarters.com Warning!! The system must be placed into Service Mode before
SCION tc SECURITY (V5) Preparation
Preparation Part Number: PT398-21070 Kit Contents Item # Quantity Reqd. Description 1 1 2 1 GBS ECU Hardware Bag Contents Item # Quantity Reqd. Description 1 1 V5 Security ECU 2 1 ECU Mounting Bracket
TWO-WAY LED MANUAL TRANSMISSION REMOTE STARTER. User Guide WARNING
TWO-WAY LED MANUAL TRANSMISSION REMOTE STARTER User Guide WARNING It is the responsibility of the vehicle operator to ensure their vehicle is parked in a safe and responsible manner. 1. When leaving the
12V PROGRAMMABLE POWER OUT
Page 1 ACCESSORIES STARTER IGNITION BATTERY WIRES SIDE VIEW BLUE RED YELLOW 30 A 10 A BLUE / WHITE YELLOW WHITE / BLUE WHITE / DOOR TRIGGER See opt. 16 DOOR TRIGGER (input positive) See opt. 16 PARKING
TOYOTA TACOMA TVIP V5
Preparation Part Number: PT398-35121 Conflicts Note: Must not be installed in Vehicles with Factory Alarm System and 2013- Vehicles with (4WD Double Cab 6MT and Off-Road Package). Kit Contents Item # Quantity
2-Way Remote Start and Door Lock Transmitter Package Installation (AP3)
Document ID: 2197450 http://gsi.xw.gm.com/si/showdoc.do?docsyskey=2197450&pubcellsyskey=176302&pu... Page 1 of 5 11/12/2009 Accessories Document ID: 2197450 2-Way Remote Start and Door Lock Transmitter
TOYOTA COROLLA 2010 TVIP V4 PREPARATION
PREPARATION Part #: PT398-02080 or PT398-02100 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: Do not install into Manual Transmission Vehicles or Vehicles
TOYOTA VENZA w/smart 2009 TVIP V4 PREPARATION
PREPARATION Part #: PT398-0T110 Conflicts: Will not program with Techstream Lite. Kit Contents RES ECU RES ECU Bracket RES Harness M6 Screw Wire Tie Splicing Connector Remote Label x1 x1 x1 x1 x5 x1 x2
TOYOTA COROLLA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
MY F150 CrewCab 1. Tools Required 10X. Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo
2013-2014MY F150 CrewCab 1 Tools Required A B C D E F G 4X H I J K 3X L 3X 2X 10X 2X Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo 2013-2014MY F150 CrewCab 2 Vehicles with selector lever in floor
Owner s manual for the AVS S-Series car alarm range Models: AVS S5 AVS S4 AVS S3 Owner s manual version: Generation 2, V4
www.avscarsecurity.com Owner s manual for the AVS S-Series car alarm range Models: AVS S5 AVS S4 AVS S3 Owner s manual version: Generation 2, V4 Thank you for choosing an AVS S-Series car security system.
P8U-FM FEATURES AND OPERATIONS REMOTE STARTER ANTI-START SYSTEM SECURITY SYSTEM
P8U-FM FEATURES AND OPERATIONS REMOTE STARTER ANTI-START SYSTEM SECURITY SYSTEM TRANSMITTER OPERATIONS Button Function Arm & Lock the Doors Disarm & Unlock the Doors Start / Stop the Engine Description
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2013 ACCORD 2 AND 4-DOOR Publications No. AII 13039 Issue Date AUG 2012 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E54-100 Transmitter
AS-1414/ AS-1424 Installation Guide
A U T O M A T I C T R A N S M I S S I O N M U L T I - C H A N N E L R E M O T E S T A R T E R S Y S T E M Installation Guide Introduction...2 Included in the Package...2 Before You Get Started...3 Harness
*(reglar key vehicles ONLY)* Read the entire installation manual. There are several safety tips in there to know before you start
Installation Tips for RS4 + EVO-RIDE + SPDT TIP SHEET T2519 2009-2011 Ford Crown Victoria 2009-2012 Ford E-150 2009 Ford E-150 Econoline Club Wagon 2008-2010 Ford E-250 2010 Ford E-250 Econoline 2010 Ford
AK-105B. ADVANCED KEYS Smart Keyless Entry + Push Start Ignition System USER MANUAL. Product Features:
AK-105B REV: A05-15-0901 ADVANCED KEYS Smart Keyless Entry + Push Start Ignition System USER MANUAL Product Features: Smart Keyless Locking/Unlocking Compact Sized Smart Keys Dual-Antenna Setup Bypass
GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION: 2 APPLICATION: 3 PART NUMBER(S) REQUIRED FOR INSTALLATION: Fog Lamp Kit Rogue w/ AL 999F1 G2000 (Fog Lamp Kit) 4 KIT CONTENTS: Item Qty. Part Description
TOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
AS-1414/ AS User Guide
AUTOMATIC TRANSMISSION MULTI-CHANNEL REMOTE STARTER SYSTEM AS-1414/ AS-1424 User Guide Introduction...2 Basic Remote Operation...2 Remote-starting Your Vehicle...2 Vehicle Presets...2 Driving Off...3 Idle
2004 Directed Electronics, Inc. Vista, CA N740T 09-04
Model 740T Installation Guide 2004 Directed Electronics, Inc. Vista, CA N740T 09-04 table of contents what is included................................................................ 3 primary harness
ALL MODELS 2002 Use Caution -
INSTALLATION AND TECHNICAL REFERENCE MANUAL WARNING! REMOTE START SYSTEMS ARE ONLY APPLICABLE TO VEHICLES WITH AUTOMATIC TRANSMISSION! BOTH ORIGINAL KEYS ARE REQUIRED FOR ALL REMOTE START SYSTEMS ON VEHICLES
FOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES
#STARTC2003-TW TWO-WAY FM/FM REMOTE CONTROL VEHICLE STARTER & ALARM SYSTEM INSTALLATION GUIDE FOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES THIS UNIT MUST BE INSTALLED BY AN AUTHORIZED MICRO ALARM
INSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE SECURITY SYSTEM PRO-SERIES 7002 CONTENTS System Features... 1-2 System Components... 2 Technical Assistance... 2 Before You Begin... 2 Precautions... 3 Making Connections...
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application Publications No. 2009 ACCORD AII 39977-40931 4-DOOR Issue Date (A/T ONLY) NOV 2008 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100A
Installation Tips for your Remote Start w/ Keyless Entry (Toyota Vehicles) v3.2 Updated 3/14/13
Installation Tips for your Remote Start w/ Keyless Entry (Toyota Vehicles) v3.2 Updated 3/14/13 Thank you for purchasing your remote start from MyPushcart.com an industry leader in providing remote starts
SCION im PREMIUM AUDIO Preparation
SCION im 2016 - PREMIUM AU Preparation Part Number: PT296-12160 (Extension Module w/ AHA) Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna
PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED
Installation Instructions CPL Master Module PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
RS-340-EDP+ / RS-450-EDP+
RS-340-EDP+ / RS-450-EDP+ Deluxe Keyless Entry & Remote Start Installation Guide July 11, 2012 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin
OWNER S GUIDE REMOTE START. Part Number: REV A 2010 HYUNDAI MOTOR AMERICA
OWNER S GUIDE Part Number: 4280279 REV A 2010 HYUNDAI MOTOR AMERICA REMOTE START REMOTE START OWNER S GUIDE INTRODUCTION Congratulations on your purchase of a Hyundai Remote Start System with Deluxe Vehicle
ELECTRONIC POSITIVE AIR SHUTOFF
12 January 2015 103675X Electronic positive air shutdown (I-00336) 1 ELECTRONIC POSITIVE AIR SHUTOFF 1036750 2007-2009 Dodge 6.7L 1036751 2010-2015 Dodge 6.7L 1036754 2008-2010 Ford 6.4L 1036755 2011-2014
Responder 350. Installation Guide
Responder 350 Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may
TOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
Operation & Installation Manual (V8.3) Keyless. Model # GTS 2 Keyless RFID Push Button Start & Security System
www.gallotech.com Operation & Installation Manual (V8.3) Keyless Model # GTS 2 Keyless RFID Push Button Start & Security System FCC Compliance This device complies with Part 15 of the FCC Rules. Operation
TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
Scion xb EC Rearview Mirror w/ Shift Light Preparation
2008 - Preparation Part Number: 00016-79800 Accessory Code: YM10 Kit Contents Item # Quantity Reqd. Description 1 1 Mirror Assembly w/ PRNDL 2 1 Hardware bag 3 1 Installation Manual Hardware Bag Contents
Remote Vehicle Control System CA-150. Owner's Manual. Vehicle Security System With Remote Keyless Entry
Remote Vehicle Control System CA-150 Owner's Manual Vehicle Security System With Remote Keyless Entry IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
TOYOTA CAMRY LE / SE / XLE DUAL SEAT HEATER KIT Section I Pre-Installation Check
Section I Pre-Installation Check Kit Part Number: 250-1897 3 General Applicability Camry LE / SE / XLE 5 4 1 Recommended Sequence of Application Item # Accessory 1 Wiring 2 Elements 3 2 Kit Contents Item
Installation Manual: Hyundai Tucson Power Lift Gate System
Installation Manual: Hyundai Tucson Power Lift Gate System Page 1 of 12 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused by improper
Scion xd EC Rearview Mirror Preparation
Scion xd 2010 - EC Rearview Mirror Preparation Part Number: 00016-09101 Code: CM9 Kit Contents Item # Quantity Reqd. Description 1 1 Mirror Assembly w/ Compass and Homelink 2 1 Hardware bag Hardware Bag
Components. Options Accessory Harness USB Charger. Quick Connector. Hook & Loop / Cable-ties. RFID Antenna. Module. Main Harness.
SRX SERIES Table of Contents - Components - Planning The Install - Mounting - Switched Power - Attach Accessory Harness - Plug In Module - Back-Up Battery - Remote Encoding - 2-Way RFID Remote User Instructions
ACD-PRO Install in 2008 EvoX
Turning in a counter clockwise direction, unscrew ift knob ACD-PRO Install in 2008 EvoX Slide back and remove the floor console panel assembly Pull up to remove the center console tray Disconnect the plug
OWNER'S MANUAL OWNER'S MANUAL MODEL: K9-FIVE C COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT 1997 AL-100-H AL-100-H
LIMITED LIFETIME WARRANTY Products manufactured and sold by Omega Research & Development, Inc. (the Company), are warranted to be free from defects in materials and workmanship under normal use. If a product
TOYOTA PRIUS XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-4700 Tuner Assy 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item # Quantity
TOYOTA VENZA 2009 TVIP V2 PREPARATION
PREPARATION Part #: PT398-0T092 Conflicts: Kit Contents Do not install into Vehicles without Factory Alarm System. GBS ECU GBS ECU Bracket GBS Harness GBS Microphone Wire Tie Foam Tape M6 Tapping Screw
TOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
Rostselmash Torum 740
Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part Number 740 Combine Kit Torum 740 4100762 1 Threaded Arm Assembly 2000311-2 1 Header
Remote Start Keyless Entry Model 1.3X Owner s Guide
Remote Start Keyless Entry Model 1.3X Owner s Guide 2011 Directed Electronics, Vista, CA G4202X 2011-03 Contents Government regulations... iii Warning! Safety first... v What s included...1 Important
2005 Directed Electronics, Inc. Vista, CA N426V 07-05
350HV Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result
OPERATING INSTRUCTIONS
EZ-1 ONE BUTTON REMOTE START SYSTEM OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Cool Start Remote Engine Starter and Keyless Entry with DP Technology by Crimestopper Security Products Inc.
GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. DESCRIPTION: APPLICATION: PART NUMBER: Accent light Kit Cube (MY2013+) 999F3 AW000 - Universal Accent Lighting Kit. 4. KIT CONTENTS: Item QTY Description
Part Number: PT
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
SUNROOF - SERVICE INFORMATION ADJUSTMENTS
SUNROOF - SERVICE INFORMATION DESCRIPTION OPERATION DIAGNOSIS AND TESTING POWER TOP - SUNROOF SUNROOF ASSEMBLY-MODULE REMOVAL INSTALLATION CHANNEL-DRAIN REMOVAL INSTALLATION COVER-GUIDE MECHANISM REMOVAL
Aftermarket Interface Module
An ISO 9001:2008 Registered Company Aftermarket Interface Module (2015-2018 Ford Transit) AIM514-B High Side Solenoid type Coolant Valve Control AIM515-B Motor Reversing type Coolant Valve Control Introduction
SECURITY CONTROL SYSTEM
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY SECTION SEC A SECURITY CONTROL SYSTEM B C D CONTENTS E BASIC INSPECTION... 3 DIAGNOSIS AND REPAIR WORKFLOW... 3 Work Flow...3 INSPECTION AND ADJUSTMENT...
FEB/20/2003 COMMANDO EZ-2500 REMOTE ENGINE STARTER WITH KEYLESS ENTRY SYSTEM INSTALLATION MANUAL 550A 1
COMMANDO EZ-2500 REMOTE ENGINE STARTER WITH KEYLESS ENTRY SYSTEM INSTALLATION MANUAL 550A 1 INTRODUCTION FEB/20/2003 INSTALLER WARNINGS This Remote Starter with Alarm System is designed to be installed
Part Number:
General Applicability This cruise control was tested and verified on: 2009-2010 Ford F-150 / E-150 2010 Ford Escape 2009-2010 Mazda Tribute This cruise control may not function correctly on unverified
Installation Tips for your Excalibur Remote Start (for Honda and Acura Vehicles) rev 11/28/2012
Installation Tips for your Excalibur Remote Start (for Honda and Acura Vehicles) rev 11/28/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts
QUICK INSTALLATION GUIDE
TWO-WAY LED MANUAL / AUTOMATIC TRANSMISSION REMOTE STARTER WITH VIRTUAL TACH SYSTEM (AS PRG-000 COMPATIBLE) QUICK INSTALLATION GUIDE TableofContents Bypass 3 Testing 3 4 4 5 6 6 Manual or Automatic Transmission
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 38163 XM SATELLITE RADIO SYSTEM 2008 ODYSSEY Issue Date OCT 2007 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SHJ-100A
Ford Escape. Installation Manual: Ford Escape. Power Lift Gate System. Page 1 of 12
Ford Escape Installation Manual: Ford Escape Power Lift Gate System Page 1 of 12 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused
TOYOTA FJ CRUISER AIR DAM/LIGHT BAR Preparation
Preparation Part Number: PT278-35071 Kit Contents Item # Quantity Reqd. Description 1 1 Air Dam / Light Bar Hardware Bag 1 Contents Item # Quantity Reqd. Description 1 2 Screw, M6x33mm, Wafer Head 2 2
CT-3471 TW. Installation Guide TWO-WAY LCD AUTOMATIC/MANUAL WITH VIRTUAL TACH SYSTEM TRANSMISSION REMOTE STARTER (AS PRG-1000 COMPATIBLE)
TWO-WAY LCD AUTOMATIC/MANUAL TRANSMISSION REMOTE STARTER WITH VIRTUAL TACH SYSTEM (AS PRG-1000 COMPATIBLE) CT-3471 TW Installation Guide Notice The manufacturer will accept no responsibility for any electrical
AS-1414/ AS-1424 User Guide
AUTOMATIC TRANSMISSION MULTI-CHANNEL REMOTE STARTER SYSTEM AS-1414/ AS-1424 User Guide Transmitter Part Number and Module Serial Number...2 Introduction...2 Basic Remote Operation...2 Remote-starting Your
Toyota Sienna. Installation Manual: Toyota Sienna. Power Lift Gate System. Page 1 of 12
Toyota Sienna Installation Manual: Toyota Sienna Power Lift Gate System Page 1 of 12 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage
PRODUCT GUIDE FT-DC2-S DOCUMENT NUMBER REVISION DATE
PRODUCT GUIDE DOCUMENT NUMBER REVISION DATE 20161025 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either
TOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
Conflicts: Toyota Tundra CrewMax w/non Sunroof Overhead Video. Part Number: Accessory Code: ED80.
Toyota Tundra CrewMax w/non Sunroof 2011-8.5 Overhead Video Part Number: 00016-00125-07 Accessory Code: ED80 Conflicts: 1.) Third Passenger Front Seating 2.) Sunroof General Applicability: Non Sunroof
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27996 ATTACHMENT KIT 2005 CIVIC HYBRID Issue Date AUG 2004 PARTS LIST Changer Attachment Kit: P/N 08B26-S5B-100 4 Washer-screws, 4 x
Installation Manual: Honda CRV Power Lift Gate System
Installation Manual: Honda CRV Power Lift Gate System Page 1 of 18 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused by improper
Mitsubishi ETACS - Smart Wiring System (SWS)
Mitsubishi ETACS - Smart Wiring System (SWS) Webpage Contents, click to jump to the location... Adjustment function - User Mode - These settings can be changed by the user, without a dealer. Adjustment
RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY)
RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY) THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY 1 BLUE...TRUNK/HOOD TRIGGER (-) INPUT BLACK/BLUE...4TH
Model 700T Installation Guide
Model 700T Installation Guide 2001 Directed Electronics, Inc. Vista, CA N700T 8-01 Rev. E 1.1 table of contents What Is Included...................... 3 Installation Points to Remember............ 3 Before
FEB.20, 2003 COMMANDO MODEL FM-870 REMOTE ENGINE STARTER WITH ALARM SYSTEM INSTALLATION MANUAL RST872 1
COMMANDO MODEL FM-0 REMOTE ENGINE STARTER WITH ALARM SYSTEM INSTALLATION MANUAL RST2 1 HJKL TABLE OF CONTENTS: INSTALLATION DIAGRAM..... 4 H1: 6 PIN HEAVY GAUGE WIRING CONNECTION.... 6 H1/1 Violet Wire
GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror with Compass and Homelink 2. APPLICATION: Juke (2011) 3. PART NUMBER: 999L1 VW002 4. KIT CONTENTS: Item Qty Description Service
TOYOTA VENZA HANDS FREE BLU LOGIC Preparation
TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
CM4200 and CM1000S Starter Control Module Installation Manual
Version Final - VF CM4200 and CM1000S Starter Control Module Installation Manual This manual is for authorized CompuStar dealers. Please thoroughly review this manual before beginning installation. If
KEYLESS ENTRY SYSTEM for TOYOTA SEQUOIA SR5
KEYLESS ENTRY SYSTEM for 2003-2007 TOYOTA SEQUOIA SR5 DEALER SERVICE AND INSTALLATION MANUAL KIT NO. 00016-0C060 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
KIA Genuine Accessories Vehicle Model Sorento (Push Button) Accessory Remote Engine Start Model Year 2011~ Difficulty ( B ) KMA Part No.
KIA Genuine Accessories Vehicle Model Sorento (Push Button) Accessory Remote ngine Start Model Year 2011~ Difficulty ( B ) KMA Part o. U8560 1U010 ote: Difficulty stated above reflects the minimum level
Owner's Manual. Remote Security and Convenience System INS0866 8/98
Remote Security and Convenience System Owner's Manual IMPORTANT NOTE: The operation of the SURESTART as described in this manual is applicable to most vehicles. However, due to the engine type and configuration
User Guide. Battery Low Voltage Warning
TWO- W A Y 5 - B U T T O N S S T L C D A U T O M A T I C / M A N U A L T R A N S M I S S I O N D I G I T A L R E M O T E S T A R T E R User Guide WARNING It is the responsibility of the vehicle operator
GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER(S) REQUIRED FOR INSTALLATION: KIT CONTENTS: Wireless Charging Kit Maxima 999F7 V4000 999Q9-AY001 (Accessory Service Connector)
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM (EXCEPT LX) 2006 ODYSSEY All 30392 Issue Date AUG 2005 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SHJ-100
Remote Starter Integration for the 2007 Toyota Camry equipped with the Smart Key System with Push Button Start
Remote Starter Integration for the 2007 Toyota Camry equipped with the Smart Key System with Push Button Start 1.0 Material required: - Remote Car Starter - Xpresskit : XK05-PKT2 or Bypasskit :PKT2 - One
Conflicts. Toyota Tacoma 2016 Frameless EC Mirror w/ Compass and HomeLink. Part Number: Accessory Code: ME4000
Toyota Tacoma 2016 Frameless EC Mirror w/ Compass and HomeLink Part Number: 00016-05463 Accessory Code: ME4000 Conflicts Note: NONE Item # Quantity Reqd. Description 1 1 Frameless Mirror w/compass 2 1