LONG TRAVEL SUSPENSION SALES GUIDE

Transcription

1 LONG TRAVEL SUSPENSION

2 LONG TRAVEL SUSPENSION SYSTEMS TOYOTA MODEL: TACOMA PRERUNNER / 4WD TACOMA 2WD 5-LUG TACOMA PRERUNNER / 4WD RUNNER RUNNER RUNNER FJ CRUISER FJ CRUISER TUNDRA TUNDRA T100/4RUNNER/PICKUP HILUX TRACK WIDTH OVER STOCK: RACE SERIES RACE SERIES RACE SERIES RACE SERIES RACE SERIES PAGE # TOTAL CHAOS Fabrication inc. provides its catalog, and any other printed materials or electronic media for your general guidance. TOTAL CHAOS Fabrication inc. does not guarantee that the information contained within, including, but not limited to, the contents of any page is up-to-date, complete and accurate, and individuals assume any risks associated with relying upon such information without checking other credible sources. In addition, a consumers reliance upon information contained within these sources when making purchasing decisions does not constitute, and should not be construed as, a contract with the TOTAL CHAOS Fabrication inc. Further, TOTAL CHAOS Fabrication inc. reserves the right to make changes to any pricing or information within these sources, at any time. Links or references to other materials and websites provided in the above-referenced sources are also for information purposes only and do not constitute TOTAL CHAOS Fabrication inc. s endorsement of products or services referenced.

3 TOYOTA TACOMA 3.5 LONG TRAVEL SYSTEM WD / PRERUNNER - 6 LUG TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86000 /// #86000F FRONT PART # [KING/RADFLO/ICON/SAW] /// #86000F [FOX ONLY] Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Part Coilover Shocks 3, Required Additional Parts for Installation TC Extended Axles (4WD MODELS ) Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Application Notes Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. Note: TC Hoop is required Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC This kit was not intended to use air bumps. WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES LIFT SPINDLES LT Bolt-on aluminum lower skid plates are designed to fit TC 3.5 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. 100% MADE 2 3

4 TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT 4WD TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86000 /// #86000F ACCESSORIES SPECIFIC TO PART #86000 /// #86000F PREP LT 4WD 4340 AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems heat treated 3.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly MID TRAVEL REAR - SPRING UNDER CONVERSION TOTAL CHAOS designed this kit to offer a light duty or heavy duty specific spring pack from Deaver Leaf Spring. (Springs are not included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock HD mounts built off the outer frame rail LD MID TRAVEL REAR - SPRING UNDER CONVERSION 1, REAR TOTAL CHAOS designed this kit to offer a light duty (LD) or heavy duty (HD) specific spring pack from Deaver Leaf Spring. (Springs included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING. Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock mounts built off the outer frame rail FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts. BOLT ON 2.0 REAR BUMP STOP KIT [FOX] F 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included. BOLT ON 2.0 REAR BUMP STOP KIT [KING] K 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included. 4 5

5 TOYOTA TACOMA 3.5 LONG TRAVEL SYSTEM W/HEIMS TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT FRONT WD / PRERUNNER - 6 LUG ACCESSORIES SPECIFIC TO PART #86000-H /// #86000F-H PART # H [KING/RADFLO/ICON/SAW] /// #86000F-H [FOX ONLY] Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Part Coilover Shocks 3, Required Additional Parts for Installation TC Extended Axles (4WD MODELS ) Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Boxed lower control arms include dual 2.5 shock tabs. Primary coil Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Application Notes Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. Note: TC Hoop is required over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. TC includes 3/4 chromoly lined heim joints for the pivots. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC This kit was not intended to use air bumps. WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES LIFT SPINDLES LT Bolt-on aluminum lower skid plates are designed to fit TC 3.5 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB DUAL SHOCK HOOPS - LONG TRAVEL ARMS Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. 100% MADE 6 7

6 TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86000-H /// #86000F-H 4WD TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86000-H /// #86000F-H PREP LT 4WD 4340 AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems heat treated 3.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly MID TRAVEL REAR - SPRING UNDER CONVERSION TOTAL CHAOS designed this kit to offer a light duty or heavy duty specific spring pack from Deaver Leaf Spring. (Springs are not included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock HD mounts built off the outer frame rail LD REAR MID TRAVEL REAR - SPRING UNDER CONVERSION 1, TOTAL CHAOS designed this kit to offer a light duty (LD) or heavy duty (HD) specific spring pack from Deaver Leaf Spring. (Springs included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING. Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock mounts built off the outer frame rail FK-REP KIT LOWER ARM URETHANE BUSHING KIT Complete TC long travel lower arm replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts. BOLT ON 2.0 REAR BUMP STOP KIT [FOX] F 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included. BOLT ON 2.0 REAR BUMP STOP KIT [KING] K 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included. 8 9

7 TOYOTA TACOMA 2 LONG TRAVEL SYSTEM TOYOTA TACOMA ACCESSORIES FOR 2 KIT FRONT WD / PRERUNNER - 6 LUG ACCESSORIES SPECIFIC TO PART #86002T /// #86002T-F PART # 86002T [KING/RADFLO/ICON/SAW] /// #86002T-F [FOX ONLY] Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Part Coilover Shocks 2, Required Additional Parts for Installation TC Extended Axles (4WD MODELS ) 86305T Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Application Notes Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. Note: TC Hoop is required Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC This kit was not intended to use air bumps. WELD - ON SPINDLE GUSSETS LT LOWER CONTROL ARM SKID PLATES Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS LIFT SPINDLES LT Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. Bolt-on aluminum lower skid plates are designed to fit TC 2 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. 100% MADE 10 11

8 TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002T /// #86002T-F 4WD TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002T /// #86002T-F PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly T MID TRAVEL REAR - SPRING UNDER CONVERSION TOTAL CHAOS designed this kit to offer a light duty or heavy duty specific spring pack from Deaver Leaf Spring. (Springs are not included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock HD mounts built off the outer frame rail LD REAR MID TRAVEL REAR - SPRING UNDER CONVERSION 1, TOTAL CHAOS designed this kit to offer a light duty (LD) or heavy duty (HD) specific spring pack from Deaver Leaf Spring. (Springs included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING. Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock mounts built off the outer frame rail FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts. BOLT ON 2.0 REAR BUMP STOP KIT [FOX] F 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included. BOLT ON 2.0 REAR BUMP STOP KIT [KING] K 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included

9 TOYOTA TACOMA 4WD / 2 PRERUNNER LONG TRAVEL - 6 LUG SYSTEM TOYOTA TACOMA ACCESSORIES FOR 2 KIT FRONT ACCESSORIES SPECIFIC TO PART #86002T-H /// #86002T-FH PART # 86002T-H [KING/RADFLO/ICON/SAW] /// #86002T-FH [FOX ONLY] Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Part Coilover Shocks 3, Required Additional Parts for Installation TC Extended Axles (4WD MODELS ) 86305T Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Boxed lower control arms include dual 2.5 shock tabs. Primary coil Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Application Notes Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. Note: TC Hoop is required over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. TC includes 3/4 chromoly lined heim joints for the pivots. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC This kit was not intended to use air bumps. WELD - ON SPINDLE GUSSETS LT LOWER CONTROL ARM SKID PLATES Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS LIFT SPINDLES LT Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. Bolt-on aluminum lower skid plates are designed to fit TC 2 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. 100% MADE 14 15

10 TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002T-H /// #86002T-FH 4WD TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002T-H /// #86002T-FH PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly T MID TRAVEL REAR - SPRING UNDER CONVERSION TOTAL CHAOS designed this kit to offer a light duty or heavy duty specific spring pack from Deaver Leaf Spring. (Springs are not included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock HD mounts built off the outer frame rail LD BOLT ON 2.0 REAR BUMP STOP KIT [FOX] F 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included REAR MID TRAVEL REAR - SPRING UNDER CONVERSION 1, TOTAL CHAOS designed this kit to offer a light duty (LD) or heavy duty (HD) specific spring pack from Deaver Leaf Spring. (Springs included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING. Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock mounts built off the outer frame rail. BOLT ON 2.0 REAR BUMP STOP KIT [KING] K 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel lower arm replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts

11 TOYOTA TACOMA 2 LONG TRAVEL RACE SERIES TOYOTA TACOMA ACCESSORIES FOR 2 KIT FRONT WD / PRERUNNER - 6 LUG ACCESSORIES SPECIFIC TO PART #86002T-R /// #86002T-R-F PART # 86002T-R [KING/RADFLO/ICON/SAW] /// #86002T-R-F [FOX ONLY] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 100% chromoly constructed Race System offers maximum ground clearance and weighs 16.8 pounds less than the standard TC +2 LT kit. 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS LIFT SPINDLES Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) 86305T Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE 18 19

12 TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002T-R /// #86002T-R-F 4WD TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002T-R /// #860002T-R-F PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly T MID TRAVEL REAR - SPRING UNDER CONVERSION TOTAL CHAOS designed this kit to offer a light duty or heavy duty specific spring pack from Deaver Leaf Spring. (Springs are not included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock HD mounts built off the outer frame rail LD REAR MID TRAVEL REAR - SPRING UNDER CONVERSION 1, TOTAL CHAOS designed this kit to offer a light duty (LD) or heavy duty (HD) specific spring pack from Deaver Leaf Spring. (Springs included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING. Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock mounts built off the outer frame rail FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT R Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts. BOLT ON 2.0 REAR BUMP STOP KIT [FOX] F 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included. BOLT ON 2.0 REAR BUMP STOP KIT [KING] K 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included

13 TOYOTA TACOMA 2 LONG TRAVEL RACE SERIES W/HEIMS TOYOTA TACOMA ACCESSORIES FOR 2 KIT FRONT WD / PRERUNNER - 6 LUG ACCESSORIES SPECIFIC TO PART #86002T-R-H /// #86002T-R-FH PART # 86002T-R-H [KING/RADFLO/ICON/SAW] /// #86002T-R-FH [FOX ONLY] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 100% chromoly constructed Race System offers maximum ground clearance and weighs16.8 pounds less than the standard TC +2 LT kit. 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim upper control arms are fully adjustable to allow maximum Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required tuning of caster and camber. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. TC WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS LIFT SPINDLES Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) 86305T Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE 22 23

14 TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002T-R-H /// #86002T-R-FH 4WD TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002T-R-H /// #86002T-R-FH PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly T MID TRAVEL REAR - SPRING UNDER CONVERSION TOTAL CHAOS designed this kit to offer a light duty or heavy duty specific spring pack from Deaver Leaf Spring. (Springs are not included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock HD mounts built off the outer frame rail LD BOLT ON 2.0 REAR BUMP STOP KIT [FOX] F 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included REAR MID TRAVEL REAR - SPRING UNDER CONVERSION 1, TOTAL CHAOS designed this kit to offer a light duty (LD) or heavy duty (HD) specific spring pack from Deaver Leaf Spring. (Springs included) Prerunner model Tacoma s will require drive line modifications. Adding a slip yoke on the front end is necessary. Welding is required for installation. Designed to work with factory rubber bump stops or the TOTAL CHAOS 2.0 bump stop system for FOX & KING. Wheel spacers must be installed to use stock wheels with the TC air bump or custom rear shock mounts built off the outer frame rail. BOLT ON 2.0 REAR BUMP STOP KIT [KING] K 100% bolt on bump stop bracket mounts to the factory bolt holes and replaces the factory bump stop. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT R Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts

15 TACOMA 2WD 3 LONG TRAVEL SYSTEM TACOMA 5-LUG TACOMA ACCESSORIES FOR 3 KIT ACCESSORIES SPECIFIC TO PART #88000S /// #88000F PREP PART # 88000S [KING/SAW/RADFLO/ICON] /// #88000F [FOX]RADFLO/ICON] Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. UNIBALL REMOVAL & RE-INSTALLATION TOOL Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly. PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE FK-REP KIT HI-MISALIGNMENT SPACERS LONG TRAVEL URETHANE BUSHING KIT ADDITIONAL REPLACEMENT PARTS ORDER DIRECT ONLY 3, Bolt On Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Features and Benefits 3 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Primary coil over shocks bolt into the factory coil bucket location. Tubular/plated lower control arms are designed with internal gussets and pre tabbed for a single 2.5 coil over shock that bolts to the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly. TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts. Recommended Tire & Wheel Combination Tire Wheel Backspace Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks Shock Manufacturer Fox Shocks Required Additional Parts for Installation Part Coilover Shocks Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders are required to run this kit. 100% MADE 26 27

16 TOYOTA TACOMA 3.5 LONG TRAVEL SYSTEM WD / PRERUNNER - 6 LUG TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S /// #96000K FRONT PART # 96000S [SAW] /// #96000K [KING/FOX] 2, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Tubular/plated lower control arms are designed with internal gussets and are pre tabbed for dual 2.5 shock capability. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Several spring rate options allow the ability to customize your ride for your specific application. Primary coil over shocks bolt into the factory coil bucket location. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) Race proven IFS equipment in China, Baja and South America! TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 7/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE 28 29

17 TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT 4WD TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S /// #96000K ACCESSORIES SPECIFIC TO PART #96000S /// #96000K PREP LT 4WD MODIFIED AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems. Includes remanufactured Tundra axles and CV joints that are custom modified by TC. High angle inner CV boots and clamps are installed. Fits Auto hub trucks only. Tired of tearing inner CV boots when aftermarket lift kits have been installed? Reduces inner CV angle by 2-3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly WELD ON 2.0 REAR BUMP STOP KIT [FOX] F REAR 2.0 SHOCK MOUNT KIT Weld on bump stop bracket indexes above and below the frame for maximum strength. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included wheel spacers must be installed. Provides +3 of additional droop wheel travel and better ride quality. Maximizes articulation while navigating over obstacles. Outboard shock mounting location provides additional dampening control. Utilizes a 2.0 emulsion, reservoir or bypass shock from FOX or KING. Compatible with the TOTAL CHAOS rear 2.0 bump stop kit. PT# 49623F/49623K 3/16 mild steel upper and lower laser cut shock mounts are included. Welding is required for installation wheel spacers must be installed. Grade 8 hardware included WELD ON 2.0 REAR BUMP STOP KIT [KING] K REAR Weld on bump stop bracket indexes above and below the frame for maximum strength. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included wheel spacers must be installed FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool

18 TOYOTA TACOMA 3.5 LONG TRAVEL SYSTEM W/HEIMS WD / PRERUNNER - 6 LUG TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S /// #96000K FRONT PART # 96000S-H [SAW] /// #96000K-H [KING/FOX] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Tubular/plated lower control arms are designed with internal gussets and are pre tabbed for dual 2.5 shock capability. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 7/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE 32 33

19 TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT 4WD TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S /// #96000K ACCESSORIES SPECIFIC TO PART #96000S /// #96000K PREP LT 4WD MODIFIED AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems. Includes remanufactured Tundra axles and CV joints that are custom modified by TC. High angle inner CV boots and clamps are installed. Fits Auto hub trucks only. Tired of tearing inner CV boots when aftermarket lift kits have been installed? Reduces inner CV angle by 2-3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly WELD ON 2.0 REAR BUMP STOP KIT [FOX] F REAR 2.0 SHOCK MOUNT KIT Weld on bump stop bracket indexes above and below the frame for maximum strength. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included wheel spacers must be installed. Provides +3 of additional droop wheel travel and better ride quality. Maximizes articulation while navigating over obstacles. Outboard shock mounting location provides additional dampening control. Utilizes a 2.0 emulsion, reservoir or bypass shock from FOX or KING. Compatible with the TOTAL CHAOS rear 2.0 bump stop kit. PT# 49623F/49623K 3/16 mild steel upper and lower laser cut shock mounts are included. Welding is required for installation wheel spacers must be installed. Grade 8 hardware included WELD ON 2.0 REAR BUMP STOP KIT [KING] K REAR Weld on bump stop bracket indexes above and below the frame for maximum strength. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included wheel spacers must be installed FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Lower control arm TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool

20 TOYOTA TACOMA 3.5 LONG TRAVEL SYSTEM WD / PRERUNNER - 6 LUG TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS /// #96000BK FRONT PART # 96000BS [SAW] /// #96000BK [KING/FOX] 2, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) Race proven IFS equipment in China, Baja and South America! TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 7/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE 36 37

21 TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS /// #96000BK 4WD TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS /// #96000BK PREP LT 4WD MODIFIED AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems. Includes remanufactured Tundra axles and CV joints that are custom modified by TC. High angle inner CV boots and clamps are installed. Fits Auto hub trucks only. Tired of tearing inner CV boots when aftermarket lift kits have been installed? Reduces inner CV angle by 2-3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly WELD ON 2.0 REAR BUMP STOP KIT [FOX] F REAR 2.0 SHOCK MOUNT KIT Weld on bump stop bracket indexes above and below the frame for maximum strength. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included wheel spacers must be installed. Provides +3 of additional droop wheel travel and better ride quality. Maximizes articulation while navigating over obstacles. Outboard shock mounting location provides additional dampening control. Utilizes a 2.0 emulsion, reservoir or bypass shock from FOX or KING. Compatible with the TOTAL CHAOS rear 2.0 bump stop kit. PT# 49623F/49623K 3/16 mild steel upper and lower laser cut shock mounts are included. Welding is required for installation wheel spacers must be installed. Grade 8 hardware included WELD ON 2.0 REAR BUMP STOP KIT [KING] K REAR Weld on bump stop bracket indexes above and below the frame for maximum strength. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included wheel spacers must be installed FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool

22 TOYOTA TACOMA 3.5 LONG TRAVEL SYSTEM WD / PRERUNNER - 6 LUG TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS-H /// #96000BK-H FRONT PART # 96000BS-H [SAW] /// #96000BK-H [KING/FOX] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Boxed lower control arms include dual 2.5 shock tabs. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 7/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE 40 41

23 TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS-H /// #96000BK-H 4WD TOYOTA TACOMA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS-H /// #96000BK-H PREP LT 4WD MODIFIED AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems. Includes remanufactured Tundra axles and CV joints that are custom modified by TC. High angle inner CV boots and clamps are installed. Fits Auto hub trucks only. Tired of tearing inner CV boots when aftermarket lift kits have been installed? Reduces inner CV angle by 2-3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly WELD ON 2.0 REAR BUMP STOP KIT [FOX] F REAR 2.0 SHOCK MOUNT KIT Weld on bump stop bracket indexes above and below the frame for maximum strength. Utilizes 2.5 travel FOX 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included wheel spacers must be installed. Provides +3 of additional droop wheel travel and better ride quality. Maximizes articulation while navigating over obstacles. Outboard shock mounting location provides additional dampening control. Utilizes a 2.0 emulsion, reservoir or bypass shock from FOX or KING. Compatible with the TOTAL CHAOS rear 2.0 bump stop kit. PT# 49623F/49623K 3/16 mild steel upper and lower laser cut shock mounts are included. Welding is required for installation wheel spacers must be installed. Grade 8 hardware included WELD ON 2.0 REAR BUMP STOP KIT [KING] K REAR Weld on bump stop bracket indexes above and below the frame for maximum strength. Utilizes 2 travel KING 2.0 diameter bump stops. Increases handling and performance on and off road when weight has been added to the bed of the truck. Cushions harsh bottom outs. Includes lower strike pad that bolts to the factory U bolt location. Grade 8 hardware is included wheel spacers must be installed FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Lower control arm TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool

24 4RUNNER / FJ 3.5 LONG TRAVEL SYSTEM RUNNER /// FJ CRUISER 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART # FJ /// #86004F-10FJ FRONT PART # FJ [KING/RADFLO/ICON/SAW] /// #86004F-10FJ [FOX 3, INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Travel Lift Track Increase Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. LT LOWER CONTROL ARM SKID PLATES LIFT SPINDLES LT Bolt-on aluminum lower skid plates are designed to fit TC 3.5 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS FJ Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders are required to run this kit. 100% MADE 44 45

25 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART # FJ /// #86004F-10FJ 4WD 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART # FJ /// #86004F-10FJ PREP LT 4WD 4340 AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems heat treated 3.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT FJ Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Contact our facility direct to order these items

26 4RUNNER / FJ 3.5 LONG TRAVEL SYSTEM W/HEIMS 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT FRONT RUNNER /// FJ CRUISER ACCESSORIES SPECIFIC TO PART #86004-H-10FJ /// #86004F-H-10FJ PART # H-10FJ [KING/RADFLO/ICON/SAW] /// #86004F-H-10FJ [FOX ONLY] 3, INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Travel Lift Track Increase Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Boxed lower control arms include dual 2.5 shock tabs. Primary coil Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. TC includes 3/4 chromoly lined heim joints for the pivots. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. LT LOWER CONTROL ARM SKID PLATES LIFT SPINDLES LT Bolt-on aluminum lower skid plates are designed to fit TC 3.5 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB DUAL SHOCK HOOPS - LONG TRAVEL ARMS Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS FJ Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders are required to run this kit. 100% MADE 48 49

27 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86004-H-10FJ /// #86004F-H-10FJ 4WD 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86004-H-10FJ /// #86004F-H-10FJ PREP LT 4WD 4340 AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems heat treated 3.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LOWER ARM URETHANE BUSHING KIT FJ Complete TC long travel lower arm replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Contact our facility direct to order these items

28 4RUNNER / FJ 2 LONG TRAVEL SYSTEM 4RUNNER / FJ ACCESSORIES FOR 2 KIT FRONT RUNNER /// FJ CRUISER ACCESSORIES SPECIFIC TO PART # FJ /// #86002F-10FJ PART # FJ [KING/RADFLO/ICON/SAW] /// #86002F-10FJ [FOX 2, INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Travel Lift Track Increase Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 2 extended upper and lower control arms bolt to factory mounting locations Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC WELD - ON SPINDLE GUSSETS LT LOWER CONTROL ARM SKID PLATES LIFT SPINDLES LT Eliminates the factory sway bar. Bolt-on aluminum lower skid plates are designed to fit TC 2 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS FJ Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders not required on FJ Cruisers. 4Runners are limited to 275/70R17 tires unless fiberglass is installed. Fiberglass fenders or extreme fender modifications/cutting required on Tacoma. 100% MADE 52 53

29 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART # FJ /// #86002F-10FJ 4WD 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART # FJ /// #86002F-10FJ PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT FJ Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Contact our facility direct to order these items

30 4RUNNER / FJ 4RUNNER 2 LONG /// TRAVEL SYSTEM FJ CRUISER W/HEIMS 4RUNNER / FJ ACCESSORIES FOR 2 KIT FRONT ACCESSORIES SPECIFIC TO PART #86002-H-10FJ /// #86002F-H-10FJ PART # H-10FJ [KING/RADFLO/ICON/SAW] /// #86002F-H-10FJ [FOX ONLY] 3, INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Travel Lift Track Increase Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 2 extended upper and lower control arms bolt to factory mounting locations Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks bucket location. Note: TC Hoop is required Several spring rate options allow the ability to customize your ride for your specific application. TC includes 3/4 chromoly lined heim joints for the pivots. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC WELD - ON SPINDLE GUSSETS LT LOWER CONTROL ARM SKID PLATES LIFT SPINDLES LT Eliminates the factory sway bar. Bolt-on aluminum lower skid plates are designed to fit TC 2 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS FJ Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders not required on FJ Cruisers. 4Runners are limited to 275/70R17 tires unless fiberglass is installed. Fiberglass fenders or extreme fender modifications/cutting required on Tacoma. 100% MADE 56 57

31 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-H-10FJ /// #86002F-H-10FJ 4WD 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-H-10FJ /// #86002F-H-10FJ PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT FJ Complete TC long travel lower arm replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Contact our facility direct to order these items

32 4RUNNER / FJ 2 LONG TRAVEL RACE SERIES 4RUNNER / FJ ACCESSORIES FOR 2 KIT FRONT RUNNER /// FJ CRUISER ACCESSORIES SPECIFIC TO PART #86002-R-10FJ /// #86002-R-10FJ-F PART # R-10FJ [KING/RADFLO/ICON/SAW] /// #86002-R-10FJ-F [FOX ONLY] 3, INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Travel Lift Track Increase Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 100% chromoly constructed Race System offers maximum ground clearance and weighs 16.8 pounds less than the standard TC +2 LT kit. 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC WELD - ON SPINDLE GUSSETS LIFT SPINDLES Eliminates the factory sway bar. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS FJ Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders not required on FJ Cruisers. 4Runners are limited to 275/70R17 tires unless fiberglass is installed. Fiberglass fenders or extreme fender modifications/cutting required on Tacoma. 100% MADE 60 61

33 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-R-10FJ /// #86002-R-10FJ-F 4WD 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-R-10FJ /// # R-10FJ-F PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT FJ Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Contact our facility direct to order these items

34 4RUNNER / FJ 2 LONG TRAVEL RACE SERIES W/HEIMS 4RUNNER / FJ ACCESSORIES FOR 2 KIT FRONT RUNNER /// FJ CRUISER ACCESSORIES SPECIFIC TO PART #86002-R-H-10FJ /// #86002-R-H-10FJ-F PART # R-H-10FJ [KING/RADFLO/ICON/SAW] /// #86002-R-FH [FOX ONLY] 3, INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Travel Lift Track Increase Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 100% chromoly constructed Race System offers maximum ground clearance and weighs16.8 pounds less than the standard TC +2 LT kit. 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim upper control arms are fully adjustable to allow maximum Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required tuning of caster and camber. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. TC WELD - ON SPINDLE GUSSETS LIFT SPINDLES Eliminates the factory sway bar. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS FJ Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders not required on FJ Cruisers. 4Runners are limited to 275/70R17 tires unless fiberglass is installed. Fiberglass fenders or extreme fender modifications/cutting required on Tacoma. 100% MADE 64 65

35 TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-R-H-10FJ /// #86002-R-H-10FJ-F 4WD TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-R-H-10FJ /// #86002-R-H-10FJ-F PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT FJ Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Contact our facility direct to order these items

36 4RUNNER / FJ 3.5 LONG TRAVEL SYSTEM RUNNER /// FJ CRUISER 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86004 /// #86004F FRONT PART # [KING/RADFLO/ICON/SAW] /// #86004F [FOX ONLY] Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Part Coilover Shocks 3, Required Additional Parts for Installation TC Extended Axles (4WD MODELS ) Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Application Notes Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. Note: TC Hoop is required Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC This kit was not intended to use air bumps. Fiberglass fenders are required to run this kit. WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES LIFT SPINDLES LT Bolt-on aluminum lower skid plates are designed to fit TC 3.5 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. 100% MADE 68 69

37 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT 4WD 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86004 /// #86004F ACCESSORIES SPECIFIC TO PART #86004 /// #86004F PREP LT 4WD 4340 AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems heat treated 3.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Customers should contact our facility directly to order these items

38 4RUNNER / FJ 3.5 LONG TRAVEL SYSTEM W/HEIMS 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT FRONT RUNNER /// FJ CRUISER ACCESSORIES SPECIFIC TO PART #86004-H /// #86004F-H PART # H [KING/RADFLO/ICON/SAW] /// #86004F-H [FOX ONLY] Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Part Coilover Shocks 3, Required Additional Parts for Installation TC Extended Axles (4WD MODELS ) Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Boxed lower control arms include dual 2.5 shock tabs. Primary coil Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Application Notes Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. Note: TC Hoop is required over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. TC includes 3/4 chromoly lined heim joints for the pivots. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC This kit was not intended to use air bumps. Fiberglass fenders are required to run this kit. WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES LIFT SPINDLES LT Bolt-on aluminum lower skid plates are designed to fit TC 3.5 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB DUAL SHOCK HOOPS - LONG TRAVEL ARMS Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. 100% MADE 72 73

39 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86004-H /// #86004F-H 4WD 4RUNNER / FJ ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #86004-H /// #86004F-H PREP LT 4WD 4340 AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems heat treated 3.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LOWER ARM URETHANE BUSHING KIT Complete TC long travel lower arm replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Customers should contact our facility directly to order these items

40 4RUNNER / FJ 2 LONG TRAVEL SYSTEM 4RUNNER / FJ ACCESSORIES FOR 2 KIT FRONT RUNNER /// FJ CRUISER ACCESSORIES SPECIFIC TO PART #86002 /// #86002-F PART # [KING/RADFLO/ICON/SAW] /// #86002-F [FOX ONLY] Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Part Coilover Shocks 2, Required Additional Parts for Installation TC Extended Axles (4WD MODELS ) Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS 2 extended upper and lower control arms bolt to factory mounting locations Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Application Notes Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Features and Benefits Note: TC Hoop is required the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC Fiberglass fenders not required on FJ Cruisers. 4Runners are limited to 275/70R17 tires unless fiberglass is installed. Fiberglass fenders or extreme fender modifications/cutting required on Tacoma. WELD - ON SPINDLE GUSSETS LT LOWER CONTROL ARM SKID PLATES Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS LIFT SPINDLES LT Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. Bolt-on aluminum lower skid plates are designed to fit TC 2 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. 100% MADE 76 77

41 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002 /// #86002-F 4WD 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002 /// #86002-F PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Customers should contact our facility directly to order these items

42 4RUNNER / FJ 4RUNNER 2 LONG /// TRAVEL SYSTEM FJ CRUISER W/HEIMS 4RUNNER / FJ ACCESSORIES FOR 2 KIT FRONT ACCESSORIES SPECIFIC TO PART #86002-H /// #86002-FH PART # H [KING/RADFLO/ICON/SAW] /// #86002F-H [FOX ONLY] Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Part Coilover Shocks 3, Required Additional Parts for Installation TC Extended Axles (4WD MODELS ) Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS 2 extended upper and lower control arms bolt to factory mounting locations Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Application Notes Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Features and Benefits bucket location. Note: TC Hoop is required Several spring rate options allow the ability to customize your ride for your specific application. TC includes 3/4 chromoly lined heim joints for the pivots. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC Fiberglass fenders not required on FJ Cruisers. 4Runners are limited to 275/70R17 tires unless fiberglass is installed. Fiberglass fenders or extreme fender modifications/cutting required on Tacoma. WELD - ON SPINDLE GUSSETS LT LOWER CONTROL ARM SKID PLATES Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS LIFT SPINDLES LT Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. Bolt-on aluminum lower skid plates are designed to fit TC 2 long travel system lower control arms. Slide over rocks with an angled approach front lip. Grade 8 mounting hardware is included. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. 100% MADE 80 81

43 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-H /// #86002-FH 4WD 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-H /// #86002-FH PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel lower arm replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Customers should contact our facility directly to order these items

44 4RUNNER / FJ 2 LONG TRAVEL RACE SERIES 4RUNNER / FJ ACCESSORIES FOR 2 KIT FRONT RUNNER /// FJ CRUISER ACCESSORIES SPECIFIC TO PART #86002-R /// #86002-R-F PART # R [KING/RADFLO/ICON/SAW] /// #86002-R-F [FOX ONLY] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 100% chromoly constructed Race System offers maximum ground clearance and weighs 16.8 pounds less than the standard TC +2 LT kit. 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! TC WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS LIFT SPINDLES Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders not required on FJ Cruisers. 4Runners are limited to 275/70R17 tires unless fiberglass is installed. Fiberglass fenders or extreme fender modifications/cutting required on Tacoma. 100% MADE 84 85

45 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-R /// #86002-R-F 4WD 4RUNNER / FJ ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-R /// # R-F PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT R Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Customers should contact our facility directly to order these items

46 4RUNNER / FJ 2 LONG TRAVEL RACE SERIES 4RUNNER / FJ ACCESSORIES FOR 2 KIT FRONT RUNNER /// FJ CRUISER ACCESSORIES SPECIFIC TO PART #86002-R-H /// #86002-R-FH PART # R-H [KING/RADFLO/ICON/SAW] /// #86002-R-FH [FOX ONLY] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS [FOX ONLY] LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 100% chromoly constructed Race System offers maximum ground clearance and weighs 16.8 pounds less than the standard TC +2 LT kit. 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim upper control arms are fully adjustable to allow maximum Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required tuning of caster and camber. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. TC WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS LIFT SPINDLES Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. Increases cross member ground clearance and adds 3.5 of lift. Designed to strengthen and reinforce known weak areas. Fully custom fabricated lift spindle uses CNC machined bearing housings and caliper tabs with custom CNC laser cut parts. Rugged boxed design for race or play applications. Includes semi gloss black powder coat. Extended D.O.T. stainless braided brake lines are included. *These will only fit Prerunner & 6-Lug 2WD vehicles. SPINDLE GUSSETS WITH SWAY BAR MOUNTS SB Retains the factory sway bar and includes an additional steering arm gusset. Trucks running factory back spacing wheels must run wheel spacers. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders not required on FJ Cruisers. 4Runners are limited to 275/70R17 tires unless fiberglass is installed. Fiberglass fenders or extreme fender modifications/cutting required on Tacoma. 100% MADE 88 89

47 TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-R-H /// #86002-R-FH 4WD TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-R-H /// #86002-R-FH PREP LT 4WD 4340 AXLES +2 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly CHROMOLY ADJUSTABLE REAR LINKS 1, Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Offers 1.5 more droop travel over stock when longer shocks are installed. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included LOWER LINK SKIDS REAR Grade 8-9/16 mounting hardware is included. Laser cut pre bent 3/16 mild steel brackets. Compatible only with TC or stock links. Can be welded on for maximum protection FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT R Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Customers should contact our facility directly to order these items

48 TOYOTA 4RUNNER 3.5 LONG TRAVEL SYSTEM WD / 2WD TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S-4 /// #96000K-4 FRONT PART # 96000S-4 [SAW] /// #96000K-4 [KING/FOX] 2, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Tubular/plated lower control arms are designed with internal gussets and are pre tabbed for dual 2.5 shock capability. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Several spring rate options allow the ability to customize your ride for your specific application. Primary coil over shocks bolt into the factory coil bucket location. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) Race proven IFS equipment in China, Baja and South America! TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 3/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE 92 93

49 TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S-4 /// #96000K-4 4WD TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S-4 /// #96000K-4 PREP LT 4WD MODIFIED AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems. Includes remanufactured Tundra axles and CV joints that are custom modified by TC. High angle inner CV boots and clamps are installed. Fits Auto hub trucks only. Tired of tearing inner CV boots when aftermarket lift kits have been installed? Reduces inner CV angle by 2-3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT CHROMOLY ADJUSTABLE REAR LINKS Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included. Reuses factory hardware. REAR LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts. BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool

50 TOYOTA 4RUNNER 3.5 LONG TRAVEL SYSTEM W/HEIMS WD / 2WD TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S-4H /// #96000K-4H FRONT PART # 96000S-4H [SAW] /// #96000K-4H [KING/FOX] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Tubular/plated lower control arms are designed with internal gussets and are pre tabbed for dual 2.5 shock capability. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 3/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE 96 97

51 TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S-4H /// #96000K-4H 4WD TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000S-4H /// #96000K-4H PREP LT 4WD MODIFIED AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems. Includes remanufactured Tundra axles and CV joints that are custom modified by TC. High angle inner CV boots and clamps are installed. Fits Auto hub trucks only. Tired of tearing inner CV boots when aftermarket lift kits have been installed? Reduces inner CV angle by 2-3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT CHROMOLY ADJUSTABLE REAR LINKS Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included. Reuses factory hardware. REAR LONG TRAVEL URETHANE BUSHING KIT Lower control arm TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts. BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool

52 TOYOTA 4RUNNER 3.5 LONG TRAVEL SYSTEM WD / 2WD TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS-4 /// #96000BK-4 FRONT PART # 96000BS-4 [SAW] /// #96000BK-4 [KING/FOX] 2, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) Race proven IFS equipment in China, Baja and South America! TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 3/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE

53 TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS-4 /// #96000BK-4 4WD TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS-4 /// #96000BK-4 PREP LT 4WD MODIFIED AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems. Includes remanufactured Tundra axles and CV joints that are custom modified by TC. High angle inner CV boots and clamps are installed. Fits Auto hub trucks only. Tired of tearing inner CV boots when aftermarket lift kits have been installed? Reduces inner CV angle by 2-3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT CHROMOLY ADJUSTABLE REAR LINKS Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included. Reuses factory hardware. REAR LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts

54 TOYOTA 4RUNNER 3.5 LONG TRAVEL SYSTEM W/HEIMS WD / 2WD TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS-4H /// #96000BK-4H FRONT PART # 96000BS-4H [SAW] /// #96000BK-4H [KING/FOX] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Boxed lower control arms include dual 2.5 shock tabs. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 3/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld-to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE

55 TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS-4H /// #96000BK-4H 4WD TOYOTA 4RUNNER ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #96000BS-4H /// #96000BK-4H PREP LT 4WD MODIFIED AXLES +3.5 EXTENDED 1 DIFF. DROP SPACER KIT 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC +3.5 long travel systems. Includes remanufactured Tundra axles and CV joints that are custom modified by TC. High angle inner CV boots and clamps are installed. Fits Auto hub trucks only. Tired of tearing inner CV boots when aftermarket lift kits have been installed? Reduces inner CV angle by 2-3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT CHROMOLY ADJUSTABLE REAR LINKS Constructed from 1 1/4.375 wall 4130 chromoly tubing for maximum strength. Includes urethane pivot bushings. Upper, lower and pan hard bars are designed to incorporate a heim joint making the entire rear link system length adjustable. Hi-misalignment spacers are included. Reuses factory hardware. REAR LONG TRAVEL URETHANE BUSHING KIT Lower control arm TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts. BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool

56 TUNDRA / SEQUOIA 2.5 LONG TRAVEL SYSTEM TUNDRA /// SEQUOIA TUNDRA / SEQUOIA ACCESSORIES FOR 2.5 KIT ACCESSORIES SPECIFIC TO PART #87000 FRONT PART # [FOX/KING/RADFLO/ICON] Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS WELD - ON SPINDLE GUSSETS Factory spindles are forged, not cast and gussets can be MIG or TIG welded directly to them. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS DUAL SHOCK HOOPS - LONG TRAVEL ARMS 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 35 /12.5/R17 17x /12.5/R17 17x CORE Bolt On Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks Shock Manufacturer Fox Shocks Features and Benefits 2.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 16 Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Primary coil over shocks bolt into the factory coil bucket location. TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required 4130 chromoly tubular/plated lower control arms are equipped with internal gussets and feature dual 2.5 lower shock tabs. Several spring rate options allow the ability to customize your ride for your specific application. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. A factory lower ball joint cradle CORE FEE applies. The TC kit includes an already modified set for easy installation. TC Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are pre welded in place to aid in secondary shock set up and installation. Includes grade 8 hardware. LT 4WD 4340 AXLES +2.5 EXTENDED Designed for use with TC +2.5 long travel systems heat treated 2.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. 1 DIFF. DROP SPACER KIT WD Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders are required to run this kit. 100% MADE

57 TUNDRA / SEQUOIA ACCESSORIES FOR 2.5 KIT ACCESSORIES SPECIFIC TO PART #87000 REAR TUNDRA / SEQUOIA ACCESSORIES FOR 2.5 KIT ACCESSORIES SPECIFIC TO PART # /4 LIFT SHACKLES REAR SHOCK MOUNT KIT & LEAF SPRING CONVERSION Laser cut 3/8 steel shackles lift the rear of the Tundra 3/4 over stock. Hardware included. Compatible with factory or aftermarket Deaver leaf springs Maximizes rear suspension wheel travel without drilling holes in the bed. Under the axle Deaver leaf spring conversion is designed to use tube bypass shocks. TC bolt on Jounce bump stop frame bracket replaces factory rubber bump stop mounts. Weld on lower strike pad is included. Cutting, welding and grinding is required to install. TC extended shackles, weld on upper shock mounts, weld on lower shock mounts, u-bolt plates, extended brake line, weld on strike pad for Jounce bump stops, TC bolt on Jounce bump stop mount, & hardware is included. PREP 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. UNIBALL REMOVAL & RE-INSTALLATION TOOL Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly. ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts

58 TUNDRA / SEQUOIA 2.5 LONG TRAVEL SYSTEM W/HEIMS TUNDRA /// SEQUOIA TUNDRA / SEQUOIA ACCESSORIES FOR 2.5 KIT ACCESSORIES SPECIFIC TO PART #87000-H FRONT PART # H [FOX/KING/RADFLO/ICON] Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS LIMIT STRAPS W/ ADJUSTERS & MOUNTS WELD - ON SPINDLE GUSSETS Factory spindles are forged, not cast and gussets can be MIG or TIG welded directly to them. LOWER CONTROL ARM CAM TAB GUSSETS Reinforces weak factory cam alignment tab plates that bend during bottom outs or hard front impacts. CNC laser cut 1/ chromoly replacement cam plates weld to the frame. 1/4 thick lower cam alignment tabs will not bend like factory tabs. Welding and grinding are required for installation. GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS DUAL SHOCK HOOPS - LONG TRAVEL ARMS 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 35 /12.5/R17 17x /12.5/R17 17x Bolt On +CORE Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks Shock Manufacturer Fox Shocks Features and Benefits 2.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 16 Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required Primary coil over shocks bolt into the factory coil bucket location chromoly tubular/plated lower control arms are equipped with internal gussets and feature dual 2.5 lower shock tabs. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. A factory lower ball joint cradle CORE FEE applies. The TC kit includes an already modified set for installation. TC Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are pre welded in place to aid in secondary shock set up and installation. Includes grade 8 hardware. LT 4WD 4340 AXLES +2.5 EXTENDED Designed for use with TC +2.5 long travel systems heat treated 2.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. 1 DIFF. DROP SPACER KIT WD Reduces inner CV angle by 3 degrees. Reduces friction wear and tear on stock length axle inner CV boots with auto locking hubs. 1 thick zinc plated steel spacers and grade 8 hardware are included. Some vehicles may require additional washers to reinstall the factory skid plate. Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. Fiberglass fenders are required to run this kit. 100% MADE

59 TUNDRA / SEQUOIA ACCESSORIES FOR 2.5 KIT ACCESSORIES SPECIFIC TO PART #87000-H REAR TUNDRA / SEQUOIA ACCESSORIES FOR 2.5 KIT ACCESSORIES SPECIFIC TO PART # /4 LIFT SHACKLES REAR SHOCK MOUNT KIT & LEAF SPRING CONVERSION Laser cut 3/8 steel shackles lift the rear of the Tundra 3/4 over stock. Hardware included. Compatible with factory or aftermarket Deaver leaf springs Maximizes rear suspension wheel travel without drilling holes in the bed. Under the axle Deaver leaf spring conversion is designed to use tube bypass shocks. TC bolt on Jounce bump stop frame bracket replaces factory rubber bump stop mounts. Weld on lower strike pad is included. Cutting, welding and grinding is required to install. TC extended shackles, weld on upper shock mounts, weld on lower shock mounts, u-bolt plates, extended brake line, weld on strike pad for Jounce bump stops, TC bolt on Jounce bump stop mount, & hardware is included. PREP 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. UNIBALL REMOVAL & RE-INSTALLATION TOOL Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly. ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts

60 TOYOTA TUNDRA 3.5 LONG TRAVEL SYSTEM WD / 4WD TOYOTA TUNDRA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #97000S /// #97000K /// 97004S /// #97004K FRONT PART # 97000S [SAW] /// #97000K [KING/FOX] # 97004S [SAW] /// #97004K [KING/FOX] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16x /70/R17 17x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Tubular/plated lower control arms are designed with internal gussets and are pre tabbed for dual 2.5 shock capability. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Several spring rate options allow the ability to customize your ride for your specific application. Primary coil over shocks bolt into the factory coil bucket location. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) Race proven IFS equipment in China, Baja and South America! TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 7/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE

61 TOYOTA TUNDRA ACCESSORIES FOR 3.5 KIT 4WD TOYOTA TUNDRA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #97000S /// #97000K /// 97004S /// #97004K ACCESSORIES SPECIFIC TO PART #97000S /// #97000K /// 97004S /// #97004K PREP LT 4WD MODIFIED AXLES +3.5 EXTENDED Designed for use with TC +3.5 long travel systems. High angle inner CV boots and clamps are included heat treated 3.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints. 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. UNIBALL REMOVAL & RE-INSTALLATION TOOL Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly TUNDRA REAR LOWERING SHACKLES Lowers rear suspension 3/4 & improves handling. Reuses factory hardware. Includes urethane bushings and inner sleeves. For use with stock or after market leaf springs. Required when doing a under axle leaf spring conversion. REAR FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool

62 TOYOTA TUNDRA 3.5 LONG TRAVEL SYSTEM WD / 4WD TOYOTA TUNDRA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #97000BS /// #97000BK /// 97004BS /// #97004BK FRONT PART # 97000BS [SAW] /// #97000BK [KING/FOX] # 97004BS [SAW] /// #97004BK [KING/FOX] 3, Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 285/70/R17 17 x Bolt On Shock Manufacturer Fox Shocks Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.5 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. Optional remanufactured Tundra axles and CV joints that are custom modified by TC to retain 4WD. (not included) Race proven IFS equipment in China, Baja and South America! TC Note: TC Hoop [SAW] or [FOX/KING] is required WELD - ON SPINDLE GUSSETS Eliminates the factory sway bar. WELD - ON UPPER COIL BUCKET TOWER GUSSETS Reduces upper coil bucket flex and double shears factory upper control arm bolt. Compatible only with TC UCA s or L/T kits, not intended for use with factory control arms. LT LOWER CONTROL ARM SKID PLATES Eliminates the rack movement caused by worn out rubber bushings. Replaces all 3 factory rubber bushings. LONG TRAVEL HEIM JOINT STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 7/ chromoly heim joints replace factory outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters are supplied. Designed to fit TC long travel systems ONLY. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up Includes grade 8 hardware [SAW] [FOX/KING] Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE

63 TOYOTA TUNDRA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #97000BS /// #97000BK /// 97004BS /// #97004BK 4WD TOYOTA TUNDRA ACCESSORIES FOR 3.5 KIT ACCESSORIES SPECIFIC TO PART #97000BS /// #97000BK /// 97004BS /// #97004BK PREP LT 4WD AXLES +3.5 EXTENDED Designed for use with TC +3.5 long travel systems. High angle inner CV boots and clamps are included heat treated 3.5 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints. 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. UNIBALL REMOVAL & RE-INSTALLATION TOOL Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly TUNDRA REAR LOWERING SHACKLES Lowers rear suspension 3/4 & improves handling. Reuses factory hardware. Includes urethane bushings and inner sleeves. For use with stock or after market leaf springs. Required when doing a under axle leaf spring conversion. REAR FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts BALL JOINT REMOVAL- SLUG ADAPTER INSTALL TOOLS Aids in the removal of the factory ball joint from the spindle. Also designed to assist in the TC slug adapter installation. Requires a large C clamp tool or press tool

64 TOYOTA T LONG TRAVEL SYSTEM WD TOYOTA T100 ACCESSORIES FOR 3.25 KIT ACCESSORIES SPECIFIC TO PART #95200 FRONT PART # Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS WELD-ON DROOP STOPS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS GRADE 8 HARDWARE HEIM-STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 3/ chromoly heim joints replace factory inner and outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters supplied. CADDY IDLER ARM Custom 100% bolt on idler arm eliminates sloppy steering and provides better steering response when larger tires are installed. Designed to handle extreme elements & perform under race conditions. Laser cut brackets bolt to the factory idler arm mounting location. Fully rebuild able idler arm features double stacked sealed roller bearings. 3/4 Grade 8 hardware includes an inner sleeve to prevent over tightening during maintenance. Idler arm comes pre assembled. HI-MISALIGNMENT SPACERS LOWER UNIBALL CONVERSION GEN 2 CADDY KIT WELD-ON SHOCK HOOP 2, Bolt On Travel Lift Track Increase 12 w/4wd INSTALLATION INSTRUCTIONS Features and Benefits 3.25 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. The Caddy Kit is designed to incorporate a coil over shock conversion that uses an 8 travel 2.5 coil over shock. (TC weld on shock hoop kit available separately) Several spring rate options allow the ability to customize your ride for your specific application. Tubular/plated lower control arms are designed with internal gussets and are pre tabbed for dual 2.5 shock capability. Maximize tune ability, overall articulation & performance. Custom 4340 axles must be installed to retain 4WD. (not included) Designed to add strength and replace factory lower ball joints that become worn or damaged during off road use CNC billet machined lower uniball adapters bolt to the factory spindle. Fits aftermarket suspension systems that retain factory ball joint & spindle. 1 uniballs are feature a stainless steel ball and race for added corrosion resistance. TC heat treated custom 17-4 stainless steel himisalignment spacers are included. Custom tapered head grade 8 hardware allows for maximum articulation and travel Pre-bent 4130 chromoly shock hoops are designed to install coil over shocks from FOX/KING/ Sway A Way. CNC laser cut cross shaft bolt on plates are used to construct the coil over shock mount tower that ties into main shock hoop. Extended cross shaft hardware is supplied. Included pre cut 4130 chromoly support tubes to maximize upper shock mount strength. Secondary shock tabs, weld on remote reservoir mounts and grade 8 hardware is included. Welding and grinding are required for installation. ADDITIONAL PRODUCT INFO & IMAGES Recommended Tire & Wheel Combination Tire Wheel Backspace 33 /R15 15 x Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks Shock Manufacturer Fox Shocks 8 Travel Travel 2.5 Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks 8 Travel Travel 2.5 Note: TC Hoop Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to install supplied droop stops. This kit was not intended to use air bumps. 100% MADE

65 TOYOTA T100 ACCESSORIES FOR 3.25 KIT 4WD TOYOTA T100 ACCESSORIES FOR 3.25 KIT ACCESSORIES SPECIFIC TO PART #95200 ACCESSORIES SPECIFIC TO PART #95200 PREP LONG TRAVEL 4WD 4340 AXLES 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC long travel system heat treated 3.5 extended axle shafts and high angle inner CV boots and clamps are included. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly. ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts

66 TOYOTA T LONG TRAVEL SYSTEM BOXED WD TOYOTA T100 ACCESSORIES FOR 3.25 KIT ACCESSORIES SPECIFIC TO PART #95200-B FRONT PART # B Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS WELD-ON DROOP STOPS D.O.T. BRAIDED BRAKE LINES LOWER 1 UNIBALL CONVERSION 1 UNIBALLS W/ RETAINING CLIPS BOLT-ON UPPER SHOCK MOUNTS HEIM-STEERING UPGRADE Maximize wheel travel and component strength while eliminating sloppy steering zinc plated extended chromoly tie-rods. 3/ chromoly heim joints replace factory inner and outer tie rod ends. Laser cut weld-on double shear steering arm gussets are included. Grade 8 hardware and tapered steering arm adapters supplied. CADDY IDLER ARM Custom 100% bolt on idler arm eliminates sloppy steering and provides better steering response when larger tires are installed. Designed to handle extreme elements & perform under race conditions. Laser cut brackets bolt to the factory idler arm mounting location. Fully rebuild able idler arm features double stacked sealed roller bearings. 3/4 Grade 8 hardware includes an inner sleeve to prevent over tightening during maintenance. Idler arm comes pre assembled. 2, Bolt On Travel Lift Track Increase 12 w/4wd INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS Features and Benefits 3.25 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required. 13 Travel. Upper ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. The Caddy Kit is designed to incorporate a coil over shock conversion that uses an 8 travel 2.5 coil over shock. (TC weld on shock hoop kit available separately) Boxed lower control arms include dual 2.5 shock tabs. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. Custom 4340 axles must be installed to retain 4WD. (not included) Lower Uniball Conversion is included. LOWER UNIBALL CONVERSION Designed to add strength and replace factory lower ball joints that become worn or damaged during off road use CNC billet machined lower uniball adapters bolt to the factory spindle. Fits aftermarket suspension systems that retain factory ball joint & spindle. 1 uniballs are feature a stainless steel ball and race for added corrosion resistance. TC heat treated custom 17-4 stainless steel himisalignment spacers are included. Custom tapered head grade 8 hardware allows for maximum articulation and travel. GEN 2 CADDY KIT WELD-ON SHOCK HOOP Pre-bent 4130 chromoly shock hoops are designed to install coil over shocks from FOX/KING/ Sway A Way. CNC laser cut cross shaft bolt on plates are used to construct the coil over shock mount tower that ties into main shock hoop. Extended cross shaft hardware is supplied. Included pre cut 4130 chromoly support tubes to maximize upper shock mount strength. Secondary shock tabs, weld on remote reservoir mounts and grade 8 hardware is included. Welding and grinding are required for installation. Recommended Tire & Wheel Combination Tire Wheel Backspace 33 /R15 15 x Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks Shock Manufacturer Fox Shocks 8 Travel Travel 2.5 Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks 8 Travel Travel 2.5 Note: TC Hoop Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) Application Notes Suspension travel varies on every vehicle. Welding is required to install supplied droop stops. This kit was not intended to use air bumps. 100% MADE

67 TOYOTA T100 ACCESSORIES FOR 3.25 KIT ACCESSORIES SPECIFIC TO PART #95200-B 4WD TOYOTA T100 ACCESSORIES FOR 3.25 KIT ACCESSORIES SPECIFIC TO PART #95200-B PREP LONG TRAVEL 4WD 4340 AXLES 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT UNIBALL REMOVAL & RE-INSTALLATION TOOL Designed for use with TC long travel system heat treated 3.5 extended axle shafts and high angle inner CV boots and clamps are included. 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly. ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts

68 TOYOTA HILUX 2 LONG TRAVEL SYSTEM TOYOTA HILUX ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002V-R FRONT PART # 86002V-R Kit Includes UPPER A-ARMS W/ BUSHINGS & ZERK FITTINGS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS PLATED A-ARM END WASHERS D.O.T. BRAIDED BRAKE LINES 1 UNIBALLS W/ RETAINING CLIPS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE WELD - ON SPINDLE GUSSETS V Eliminates the factory sway bar. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. HI-MISALIGNMENT SPACERS 4WD Features and Benefits 3, Bolt On Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength. Heim pivot upper control arms can be custom ordered for this kit. Boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. Maximize tune ability, overall articulation & performance. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! 100% chromoly dual shock race system. Legal for several different racing sanctions that have limited track width rules. LT 4WD 4340 AXLES +2 EXTENDED V Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks Shock Manufacturer Fox Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required TC Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) V Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE

69 TOYOTA HILUX ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002-V PREP 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. UNIBALL REMOVAL & RE-INSTALLATION TOOL Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly. ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts

70 TOYOTA HILUX 2 LONG TRAVEL SYSTEM TOYOTA HILUX ACCESSORIES FOR 2 KIT FRONT ACCESSORIES SPECIFIC TO PART #86002V-R-H PART # 86002V-R-H Kit Includes UPPER A-ARMS W/ HEIMS LOWER A-ARMS W/ BUSHINGS TIE-ROD EXTENSIONS 1 UNIBALLS W/ RETAINING CLIPS LIMIT STRAPS W/ ADJUSTERS & MOUNTS GRADE 8 HARDWARE HI-MISALIGNMENT SPACERS WELD - ON SPINDLE GUSSETS V Eliminates the factory sway bar. DUAL SHOCK HOOPS - LONG TRAVEL ARMS Maximize vehicle dampening control when you install a dual 2.5 shock mount system prebent chromoly shock hoops are designed to install secondary 2.5 smooth body or bypass shocks for maximum IFS dampening control. Reinforces the factory coil bucket and helps reduce flex. Upper shock tabs are tacked in place to aid in secondary shock location set up. Includes grade 8 hardware. 4WD Features and Benefits 4, Bolt On Travel Lift Track Increase INSTALLATION INSTRUCTIONS ADDITIONAL PRODUCT INFO & IMAGES 2 extended upper and lower control arms bolt to factory mounting locations. Fiberglass fenders are required Travel. Upper and lower ball joints are upgraded to 1 stainless steel uniballs for max travel and component strength chromoly tubing heim upper control arms are fully adjustable to allow maximum tuning of caster and camber. 100% chromoly boxed lower control arms include dual 2.5 shock tabs. Primary coil over shocks bolt into the factory coil bucket location. Several spring rate options allow the ability to customize your ride for your specific application. TC includes 3/4 chromoly lined heim joints for the pivots. TC custom extended 4340 axles insert into the factory inner and outer CV s to retain 4wd. Race proven IFS equipment in China, Baja and South America! LT 4WD 4340 AXLES +2 EXTENDED V Designed for use with TC +2 long travel systems heat treated 2 extended axle shafts and clamps are included. Re-uses factory Toyota inner and outer CV joints and boots. Recommended Tire & Wheel Combination Tire Wheel Backspace 285/75/R16 16 x /70/R17 17 x Recommended Primary Shock Setup 2.5 Diameter Extended Travel Coilover Shocks Shock Manufacturer Fox Shocks TC Recommended Secondary Shock Setup 2.5 External Bypass Shocks Shock Manufacturer Fox Shocks Note: TC Hoop is required TC Required Additional Parts for Installation Part Coilover Shocks TC Extended Axles (4WD MODELS ) V Application Notes Suspension travel varies on every vehicle. Welding is required to mount the limit strap mounts and bump stop spacer. This kit was not intended to use air bumps. 100% MADE

71 TOYOTA TACOMA ACCESSORIES FOR 2 KIT ACCESSORIES SPECIFIC TO PART #86002V-R-H PREP 1 STAINLESS STEEL UNIBALL REPLACEMENT KIT 1 I.D. uniballs feature a heat treated stainless steel ball & heat treated stainless steel race for maximum corrosion resistance and component longevity. These uniball s also features a military grade PTFE woven fabric liner that helps prevent noise. Snap rings included. UNIBALL REMOVAL & RE-INSTALLATION TOOL Aids in the removal and reinstallation of a 1 uniball from any uniball cup during vehicle prep. Designed to be used with any hydraulic press, shop press or a hammer. Prevents damage to new uniball during reassembly FK-REP KIT LONG TRAVEL URETHANE BUSHING KIT Complete TC long travel suspension system replacement urethane bushing kit. Performance parts will require periodic maintenance based on your driving habits & local conditions. Inspect bushings and other equipment regularly. ADDITIONAL REPLACEMENT PARTS TC stocks all replacement parts necessary to maintain your performance equipment. Tie-Rod Extensions Plated A-Arm End Washers D.O.T. Braided Brake Lines Bolt-On Upper Shock Mounts [Fox only] Limit Straps w/ Adjusters & Mounts Grade 8 Hardware Hi-Misalignment Spacers Please have your customers contact TC directly for any individual replacement parts