ROLLER SHADE SPECIFICATIONS

Size: px
Start display at page:

Download "ROLLER SHADE SPECIFICATIONS"

Transcription

1 Part 1 General 1.1 Scope A. Furnish and install roller shades provided by Fabtex Inc., (800) B. Substitutions: Not Permitted C. Related work specified elsewhere 1.2 Quality Assurance A. Installer qualifications: 1. The installer shall be a firm approved by Fabtex, Inc. 2. The installer shall be qualified to install the product specified, as demonstrated by prior experience. B. Job mock-up: A sample shade may be installed on the jobsite prior to the beginning of the project. 1.3 Submittals A. Product information: Submit Fabtex product literature and installation instructions. B. Shop drawings 1. Indicate field-measured dimensions of opening which are to receive shades, details on mounting surface and sill conditions, and details of corners and conditions between adjacent shades. 2. Provide system wiring diagrams. C. Color samples: Submit a sample of each type and color of material specified. 1.4 Delivery, Storage, and Handling A. Packing and shipping: 1. Materials shall be delivered to the Project in the Fabtex original unopened packaging with labels intact. B. Storage: 1. Materials shall be stored in a clean area, which is free of corrosive fumes, dust, and away from construction activities. 2. Materials shall be stacked horizontally using plastic or wood shims such that drainage and ventilation are provided for, and such that water cannot accumulate in, about or upon containers. 3. Stacks shall be covered with tarpaulins or plastic such that ventilation is provided for, and such that contaminants are prevented from contacting surfaces. 1.5 Project/Site Conditions (Before Product Installation Begins) A. Roof must be tight, windows and frames installed and glazed, and interior doors hung. B. Wet work including concrete, masonry, plaster, stucco, terrazzo, sheetrock, spackling, and taping (including sanding) shall be complete and dry. C. Ceilings, window pockets, electrical, and mechanical work above the product shall be complete. D. Electrical power (110 volt AC) shall be available for installer s tools within 500 ft. of product installation areas. E. Flooring materials such as carpet, tile, etc. must be completed. 1.6 Warranty A. Lifetime limited warranty: Fabtex, Inc. shall repair or replace for the ten year expected life of the roller shade, at its option, without charge, any part found defective in workmanship or material as long as the roller shade remains in the same window for which it was purchased. Part 2 Products 2.1 Manufacturer and Product Description A. Acceptable product: Fabtex motorized roller shades manufactured by Fabtex, Inc. B. Motor Selection 1. PS45 Standard Drive Unit

2 a. Tubular, asynchronous operator, built in reversible capacitor, brushless 110V AC (60 Hz) single phase motor, thermally protected, permanently lubricated gearbox, maintenance free. b. Built in, digital control system, delivers automatic alignment with a +/ 2mm accuracy, programmable configuration via motor mounted push buttons. Systems using a time function for positioning are not acceptable. c. Upper and lower limits are preset by shade manufacturer and adjustable on site. d. 100 degrees of resolution: motor can be positioned at full-up, full-down or any position e. Each drive unit has a whisper quiet sound output (this can vary based on installation environment and shade manufacturer hardware). f. Wiring i. Motors can be parallel wired together to a single circuit. Total load not to exceed circuit or switch capacity. Consult a certified electrical contractor for recommended power layout. g. Programming i. Motors can be individually programmed at any time; in single or parallel wired configurations h. Power cord (5 conductor - high voltage) i. 6 feet (2m) standard 2. Plugin RTM Radio Controlled Drive Unit a. Tubular, asynchronous operator, built in reversible capacitor, brushless 110V AC (60 Hz) single phase motor, thermally protected, permanently lubricated gearbox, maintenance free. b. Built in, digital control system, delivers automatic alignment with a +/ 2mm accuracy, programmable configuration via wireless remote. Systems using a time function for positioning are not acceptable. c. Upper and lower limits are preset by shade manufacturer and adjustable on site via hand held device. d. 100 degrees of resolution: motor can be positioned at full-up, full-down or any position e. Controlling device stores the unique ID code of the motor(s) to which it is programmed. f. Each drive unit has a whisper quiet sound output (this can vary based on installation environment, mounting conditions, and selected hardware). g. Power cord (high voltage) with built in C13/C14 quick disconnect i. 1.5 feet (0.5m) ii. 3 feet (1m) iii. 6 feet (2m) standard iv. 13 feet (4m) standard v. 19 feet (6m) vi. 26 feet (8m) 3. Battery RTM Radio Controlled Drive Unit a. Tubular, asynchronous operator, internal lithium-ion battery, thermally protected, permanently lubricated gearbox, maintenance free. b. Battery is to be continuously trickle charged via i. Solar panel ii. Wall charger c. Built in, digital control system, delivers automatic alignment with a +/ 2mm accuracy, programmable configuration via wireless remote. Systems using a time function for positioning are not acceptable.

3 d. Upper and lower limits are preset by shade manufacturer and adjustable on site via hand held device. e. 100 degrees of resolution: motor can be positioned at full-up, full-down or any position f. Each drive unit has a quiet sound output (this can vary based on installation environment, mounting conditions, and selected hardware). 4. ILT Intelligent Drive Unit a. Tubular, asynchronous operator, built in reversible capacitor, brushless 110V AC (60 Hz) single phase motor, thermally protected, permanently lubricated gearbox, maintenance free. b. Built in, digital control system, delivers automatic alignment with a +/ 2mm accuracy, programmable configuration via PC. Systems using a time function for positioning are not acceptable. c. Upper and lower limits are preset by shade manufacturer and adjustable on site via hand held device, no need to access the roller assembly. No external, mechanical limit wheels or buttons are involved. d. Up to sixteen intermediate stopping points are electronically precision set and locked into non-volatile memory. e. 100 degrees of resolution: motor can be positioned at full-up, full-down or any position f. Motor can be a member of up to 16 groups; the system can have an unlimited number of groups. g. Each unit is capable of automatically aligning itself to a referenced shade position upon receiving a command from the SVI control software. h. Each drive unit has a whisper quiet sound output (this can vary based on installation environment, mounting conditions, and selected hardware). i. Power cord (high voltage) i. 6 (2m) standard ii. 12 (4m) optional iii. 18 (6m) optional iv. 24 (8m) optional j. Control Cord (low voltage) i. 6 (2m) of four conductor flat control cable with an RJ-9 modular connector. k. Testing i. Motors are UL recognized and meet CSA standards. ii. All internal electrical components are tested to withstand a 15kV electrostatic discharge without damage or loss of memory. C. Materials: 1. Fabric a. Selected from the Fabtex Roller Shade Collection. Available in a variety of solar screen, light filtering, and room darkening fabrics. b. Dual shade systems require two fabric selections. Typically one blackout and one solar screen. 2. Tube Mechanism a. All tubes shall be 100% extruded T6 aluminum with a diameter and a wall thickness required to support shade fabric without excessive deflection. Four tube extrusions shall be used depending upon the size of the shade and the weight of the fabric selected. Each tube shall have at least one internal raised rib to increase the rigidity of the tube and thus enabling shades to span wider openings without the risk of the tube sagging when the shade is operated.

4 3. Hembars: a. Standard i. An aluminum extrusion 1 in height held inside a fabric bottom-pocket. The bottompocket shall be created by folding a 1 1/4 section of fabric behind the bottom of the shade and RF welding the fabric to itself. After the aluminum weight is inserted into the bottom-pocket, the edges will be sealed by again RF welding the fabric edges to itself. b. External optional i. An aluminum extrusion in clear anodized, white, alabaster, black, or dark bronze attached to the bottom edge of the fabric ii. Available with Edge Seal stripping along the bottom edge to aid in creating a tight light gap. Typically only used for blackout bands. 4. Installation Brackets a. Without Fascia i. Standard Brackets: Shall be universal. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a zinc or white painted finish. ii. Dual Lite Brackets: required for dual shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white painted finish. b. Installation Brackets with Fascia i. Standard Box Brackets: Shall be universal. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white, bone, bronze or black painted finish. ii. Dual Lite Box Brackets: required for dual shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white, bone, bronze or black painted finish. iii. 5 Inch Box Brackets: required for 5 Inch Fascia shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a zinc, white, bronze, or black painted finish. iv. Dual Standard Box Brackets: required for dual shading systems. Brackets may be installed top, face, or side fixed and can be used for shades with both left hand and right hand controls. Brackets shall be available in a white, bone, bronze or black painted finish. 5. Valance Options a. Fascia i. 4 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with medium to large size standard shade systems and small to medium dual lite shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bone, bronze, and black. Matching fabric wrapped and custom paint available. ii. 4 Inch Round Fascia Valance: Shall be a contoured shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with medium to large size standard shade systems and small to medium dual lite shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bone, bronze, and black. Matching fabric wrapped and custom paint available.

5 iii. 5 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Can be inverted for reverse roll applications and used as back fascia for aesthetics and light leakage prevention. Designed for use with large to very-large size standard shade systems and medium to large size dual shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bronze, and black. Matching fabric wrapped and custom paint available. iv. 7 Inch Square Fascia Valance: Shall be an L shaped aluminum extrusion that covers the front and bottom of the roller. Designed for use with very-large size standard shade systems and large size dual shade systems. The fascia shall lock into its brackets with snap-in fittings. Available as clear anodized, white, bronze, and black. Matching fabric wrapped and custom paint available. b. Headbox i. Standard Shade Pocket (5.5 x 5 Headbox): Shall be a one-piece U shaped aluminum extrusion with optional removable bottom closure plate. The shade pocket will encase and conceal the roller shade tube mechanism. It is designed to be installed either in a ceiling pocket, to the ceiling, or to the wall. Aluminum end caps are available and may be fixed at both ends of the extrusion. Available as white. Custom colors available upon request. ii. Single Shade Pocket with Tile Clip (5.5 x 5 Headbox): Shall be a one-piece U shaped aluminum extrusion with front lip extension and optional removable bottom closure plate. The shade pocket will encase and conceal the roller shade tube mechanism. It is designed to be installed flush with a T-Bar type ceiling. Aluminum end caps are available and may be fixed at both ends of the extrusion. Available as white. Custom colors available upon request. iii. Dual Shade Pocket (7 x 9 Headbox): Shall be a one-piece U shaped aluminum extrusion with optional removable bottom closure plate. Designed for use with very large single roller shades and dual shade systems. The shade pocket will encase and conceal the roller shade tube mechanism. It is designed to be installed either in a ceiling pocket, to the ceiling, or to the wall. Aluminum end caps are available and may be fixed at both ends of the extrusion. Available as white. Custom colors available upon request. 6. Side & Sill Channels a. Shall be a one-piece U shaped aluminum extrusion that may be installed at each side and/or to the window sill to eliminate left, right, and bottom edge light gaps. b. Note! Side and Sill Channels are typically only used on the blackout band. 2.2 Controls A. Non-Intelligent 1. Standard Motors a. Utilizing standard switches, run shades individually or in groups. 2. RTM Motors a. Utilizing battery powered switches and remotes, run shades individually, in groups, or configure into zones. Each wireless device to have a range of 50 ft. without obstructions. 3. ILT Motors a. Utilizing low voltage switches, run shades individually, in groups, or configure into zones. Each switch directly controls the motor, group, or zone to which it is physically connected. B. Intelligent 1. ILT Motors

6 a. Control the shades using unique motor IP addresses through an RS-485 network with the ability to support up to 65,025 motors on a single control interface. b. Configurable and easily managed from any PC on the local area network. No dedicated PC is required. c. Master switch can be configured to provide a manual override for authorized personnel in specific areas. d. Optional connectivity with Building Management Systems (BMS) via RS-232 or RS-485. e. Local Control i. Virtual desktop switch ii. SVI Switch (wired). 3-6 buttons, fully programmable to single shades, groups, or desired zones. f. Sun Scheduled i. Provide active shade control based upon position of the building in relation to the sun. ii. Direct unfiltered sunlight shall not penetrate further than 6 into building interior to increase occupant comfort and reduce the load on the building s cooling system. iii. After sunset, all shades shall be lowered to increase thermal efficiency and reduce the load on the building s HVAC system. iv. System will automatically make seasonal adjustments as the sun s azimuth changes throughout the year. g. Sun Sensor i. Provide sun sensors to accommodate for cloudy days and shadows or reflections cast by surrounding buildings h. Smart Scheduling i. Shades can be set to position themselves at desired heights throughout the building based upon preset days and times. 2.3 Fabrication A. Prior to fabrication, verify actual opening dimensions by on-site measurement. Calculate roller shade dimensions to fit within specified tolerances. B. Fabricate roller shades to fill openings from head to sill and jamb to jamb. The minimum clearance shade-to-shade shall be 1/4. Locate shade divisions at mullions. Part 3 Execution 3.1 Inspection A. Verify that the work area in which the roller shades will be installed is free of conditions that interfere with roller shade installations and operations. Begin shade installation only when unsatisfactory conditions have been corrected. 1. General: The shade shall be free of sharp edges, burrs or other defects which might be harmful. When other materials result in improved specifications, they may be adopted. 2. Size Limitations: a. Maximum width: To be determined depending upon the size of the shade tube. Multiple band shade panels connected with intermediate brackets are also available. b. Maximum drop: To be determined depending upon the size of the shade tube. 3.2 Installation A. Install shades in accordance with Fabtex, Inc. procedures except as otherwise specified herein. B. Install shades with adequate clearance to permit smooth operation of shades and any sash operators. Hold roller shades 1/4 clear from each side of window opening on inside mount unless other clearance is indicated. 3.3 Cleaning A. Clean soiled shades surfaces with a mild soap solution. Do not use steam, hot water, bleach or any abrasive or solvent-based cleaners. Do not machine wash. To ensure proper drying, provide adequate ventilation for shades.

ROLLER SHADE SPECIFICATIONS

ROLLER SHADE SPECIFICATIONS Part 1 General 1.1 Scope A. Furnish and install roller shades provided by Fabtex Inc., (800) 778-2791 B. Substitutions: Not Permitted C. Related work specified elsewhere 1.2 Quality Assurance A. Installer

More information

ROLLER SHADING SYSTEMS

ROLLER SHADING SYSTEMS ROLLER SHADING SYSTEMS ROLLER SHADES A WORLD OF USES Roller shading systems provide an excellent way to control light and glare. Modern, sleek, high performance, and cost effective, our shading systems

More information

SECTION ROLLER WINDOW SHADES

SECTION ROLLER WINDOW SHADES SECTION ROLLER WINDOW SHADES Specifier: The Specifier/Design Professional is responsible for the accuracy of all project specifications, including system application and coordination with related sections.

More information

Single Manual Roller Shades

Single Manual Roller Shades Single Manual Roller Shades 10 2 8 7 4 1 5 3 9 6 10 Roller Shade Components 1) Fabric 2) Roller Tube 3) Hem Bar- available in both sealed and exposed metal 4) Clutch 5) Bead Chain 6) Tension Device 7)

More information

Bottom-Up FlexShade Single Roller

Bottom-Up FlexShade Single Roller Bottom-Up FlexShade Single Roller Patent Pending Please check all appropriate selections and attach room schedule with verified dimensions. Select Fabric* Color name, no. & openness Draper GreenScreen

More information

AlumaView AV200. A. Section Metal Fabrications: Miscellaneous for steel supports.

AlumaView AV200. A. Section Metal Fabrications: Miscellaneous for steel supports. AlumaView AV200 PART 1 GENERAL 1.1 SECTION INCLUDES A. Commercial sectional doors. 1.2 RELATED SECTIONS A. Section 05500 - Metal Fabrications: Miscellaneous for steel supports. B. Section 08710 - Door

More information

SOMFY SYSTEMS, INC. MASTER SPECIFICATION Rev 06/2013

SOMFY SYSTEMS, INC. MASTER SPECIFICATION Rev 06/2013 SECTION 12 22 16 MASTER SPECIFICATION FOR SOMFY SYSTEMS PART 1 GENERAL 1.1 SUMMARY A. The Glydea motors are a product of years of industry experience and expertise. The reliable motor solution offers a

More information

EXTRUDED ALUMINUM TEMPERED GLASS BALANCED DOORS AND ENTRANCES

EXTRUDED ALUMINUM TEMPERED GLASS BALANCED DOORS AND ENTRANCES WIKK INDUSTRIES, INC. MasterFormat 95 SECTION 08480 MasterFormat 04 SECTION 08 42 36 EXTRUDED ALUMINUM TEMPERED GLASS BALANCED DOORS AND ENTRANCES PART I GENERAL 1.1 DESCRIPTION A. Work included: Entrance

More information

EXTRUDED ALUMINUM BALANCED DOORS AND ENTRANCES

EXTRUDED ALUMINUM BALANCED DOORS AND ENTRANCES WIKK INDUSTRIES, INC. MasterFormat 95 SECTION 08480 MasterFormat 04 SECTION 08 42 36 EXTRUDED ALUMINUM BALANCED DOORS AND ENTRANCES PART 1 GENERAL 1.1 DESCRIPTION A. Work included: Entrance and vestibule

More information

A. This Section includes the following types of sectional overhead doors:

A. This Section includes the following types of sectional overhead doors: SECTION 08361 - SECTIONAL OVERHEAD DOORS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION HYDRAULIC FOUR FOLD DOORS MODEL 48 LOUVERS

SECTION HYDRAULIC FOUR FOLD DOORS MODEL 48 LOUVERS SECTION 08350 HYDRAULIC FOUR FOLD DOORS MODEL 48 LOUVERS PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1

More information

Motorized Roller Shades

Motorized Roller Shades Motorized Roller Shades 00.. www.hunterdouglascontract.com/windowcoverings MOTORIZED ROLLER SHADE - SERIES MOTOR OPERATION Also Available Banded. Fabric. Sealed Hembar. Tube.0" 00xxxx Tape m. Crown and

More information

Motorized Systems for Interior Window Coverings 2005

Motorized Systems for Interior Window Coverings 2005 12498/SMA Buyline 5973 Motorized Systems for nterior Window Coverings 2005 C O M M E R C A L H O S P T A L T Y R E S D E N T A L Complete design support and fabrication services of motorized systems; for

More information

SECTION METAL ATHLETIC SPORT LOCKERS

SECTION METAL ATHLETIC SPORT LOCKERS SECTION 10 50 13 - METAL ATHLETIC SPORT LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified

More information

Motorized Systems for Interior Window Coverings 2014

Motorized Systems for Interior Window Coverings 2014 12 25 00/SMA Buyline 5973 ized Systems for nterior Window Coverings 2014 C O M M E R C A L H O S P T A L T Y R E S D E N T A L 3351 Jack Northrop Ave., CA 90250-4426 Phone: 310-220-2600 / 800-533-3040

More information

9900 SERIES SECTION LECTURE ROOM SEATING & TABLET ARM SPECIFICATIONS

9900 SERIES SECTION LECTURE ROOM SEATING & TABLET ARM SPECIFICATIONS Clarin by Hussey: Lecture Room Seating 9900 SERIES SECTION 12560 LECTURE ROOM SEATING & TABLET ARM SPECIFICATIONS PART 1 GENERAL 1.01 SUMMARY A. Section includes: Lecture room seating and tablet arm systems.

More information

ElectroShade Motorized Shade System Table of Contents

ElectroShade Motorized Shade System Table of Contents ElectroShade Motorized Shade System Table of Contents Table of Contents Introduction.................................. 3.02 Introducing QSS and QSX the Quiet Shade Systems............... 3.03 ElectroShade

More information

SteelForm S-24C SECTIONAL OVERHEAD DOORS

SteelForm S-24C SECTIONAL OVERHEAD DOORS SteelForm S-24C SECTIONAL OVERHEAD DOORS ** NOTE TO SPECIFIER ** Raynor; commercial sectional overhead doors. This section is based on the products of Raynor, which is located at: 1101 East River Rd. P.

More information

SECTION DUCTWORK ACCESSORIES

SECTION DUCTWORK ACCESSORIES SECTION 15910 DUCTWORK ACCESSORIES PART 1- GENERAL SCOPE This sections includes accessories used in the installation of duct systems. Included are the following topics: PART 1- GENERAL Related Work Reference

More information

SECTION VistaGard ROLLING GRILLES CLEAR PANEL DESIGN

SECTION VistaGard ROLLING GRILLES CLEAR PANEL DESIGN SECTION 08330 VistaGard ROLLING GRILLES CLEAR PANEL DESIGN GENERAL NOTES TO SPECIFIER: THIS SPECIFICATION SECTION HAS BEEN PREPARED TO ASSIST DESIGN PROFESSIONALS IN THE PREPARATION OF PROJECT OFFICE MASTER

More information

Palladiom Shading System

Palladiom Shading System Lutron Palladiom Motorized Roller Shades are ideal for exposed applications. Controlled by an ultra-quiet, precision Sivoia QS Palladiom drive, these shades are mounted on solid aluminum brackets that

More information

Room-Darkening Systems The Complete Program The Complete Program

Room-Darkening Systems The Complete Program The Complete Program Room-Darkening Systems The Complete Program Room-Darkening Systems The Complete Program The Complete Program As the leading manufacturer of sunscreen roller shades, MechoSystems offers the most complete

More information

Roller Shade Section Effective August 11, 2011

Roller Shade Section Effective August 11, 2011 Roller Shade Section Effective August 11, 2011 Save a life: "Install Safety Tension Device!" Roller Shade Measuring & Ordering Instructions Selecting the Type of Mounting: Determine whether the blind is

More information

ZMC Components. For Somfy Sonesse Ultra 50 AC/DC Motor Applications 2017 V1. The Innovation Specialist

ZMC Components. For Somfy Sonesse Ultra 50 AC/DC Motor Applications 2017 V1. The Innovation Specialist ZMC Components For Somfy Sonesse Ultra 50 AC/DC Motor Applications The Innovation Specialist 2017 V1 Sonesse Ultra 50 AC/DC Motor Motor End Brackets patent pending [2.54] 64.50 [4.4] 112 RS-911 DC RS-871

More information

Dual Roller Fascia Coupled FlexShades Assembly and Installation Instructions

Dual Roller Fascia Coupled FlexShades Assembly and Installation Instructions Dual Roller Fascia Coupled FlexShades Assembly and Installation Instructions 1 Upon receiving your Coupled FlexShades, open and inspect to make sure you have received the proper sizes, fabrics, and mounting

More information

SWFcontract SOLAR SHADE SYSTEMS COMPONENTS AND ACCESSORIES LIST

SWFcontract SOLAR SHADE SYSTEMS COMPONENTS AND ACCESSORIES LIST SWFcontract SYSTEMS COMPONENTS AND ACCESSORIES LIST SWFcontract TM TRUEPERFORMANCE TM Brackets & Accessories...3 Fascia...4 Idle Ends...5 R SERIES Brackets & Accessories...5 Fascia...7 Idle Ends...8 MOTORIZED

More information

ElectroShade Motorized Shade System Table of Contents

ElectroShade Motorized Shade System Table of Contents ElectroShade Motorized Shade System Table of Contents Table of Contents Introduction.................................. 3.02 QSS and QSX the Quiet Shade Systems............... 3.03 ElectroShade Capability........................

More information

INSTALLATION INSTRUCTIONS. - Spring Loaded Tube - Beaded Chain Loop - Cordless

INSTALLATION INSTRUCTIONS. - Spring Loaded Tube - Beaded Chain Loop - Cordless INSTALLATION INSTRUCTIONS ROLLER SHADES SPRING CLUTCH TOUCHLIFT REMOTELIFT - Spring Loaded Tube - Beaded Chain Loop - Cordless - Lift Motorization Thank you for your purchase. This shade has been custom

More information

FREE STANDING WORK STATION JIB CRANE

FREE STANDING WORK STATION JIB CRANE SECTION 14661 FREE STANDING WORK STATION JIB CRANE ***** Gorbel, Inc. manufacturers a broad range of material handling cranes including monorail, bridge, gantry, and jib cranes. Numerous work station and

More information

AUTOMATIC ENTRANCES SLIDING GILDOR, INC. SECTION [08460] MODEL SLM SERIES TYPE COM

AUTOMATIC ENTRANCES SLIDING GILDOR, INC. SECTION [08460] MODEL SLM SERIES TYPE COM PART 1 - GENERAL 1.01 SUMMARY A. This Section includes the following types of automatic entrance doors: 1. Exterior and interior, bi-parting, sliding automatic entrance doors. B. Related Sections: 1. Section

More information

Shangri-La SoftTones Sheer Shadings

Shangri-La SoftTones Sheer Shadings Comfortex Sheer Solutions featuring Shangri-La Sheer Horizontal Window Shadings, Shangri-La SoftTones Sheer Shadings and Ballet Performance Drapery Sheers Price List and Reference Guide Effective June

More information

SECTION METAL LOCKERS. A. ADAAG - Americans with Disabilities Act, Accessibility Guidelines.

SECTION METAL LOCKERS. A. ADAAG - Americans with Disabilities Act, Accessibility Guidelines. Section 10_51_13_MetalLockerPenco-ProTough_8-19-09 PART 1 GENERAL SECTION 10 51 13 METAL LOCKERS 1.01 SECTION INCLUDES A. Heavy Duty Welded Tubular Frame Lockers. B. Locker benches. 1.02 REFERENCES A.

More information

SOLAR HEATING SYSTEM

SOLAR HEATING SYSTEM SECTION 13600 SOLAR HEATING SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 07600 - Flashing and Sheet Metal. 2. 07900 - Joint Sealers. 3. 15260 - Thermal Insulation (Plumbing). 4. 15410 - Piping

More information

CEILING MOUNTED WORK STATION STEEL BRIDGE CRANE

CEILING MOUNTED WORK STATION STEEL BRIDGE CRANE SECTION 14636 CEILING MOUNTED WORK STATION STEEL BRIDGE CRANE ***** Gorbel, Inc. manufactures a broad range of material handling cranes including monorail, bridge, gantry, and jib cranes. Numerous work

More information

DORMA Automatics, Inc. 924 Sherwood Drive Lake Bluff, Illinois U.S.A. Toll Free: Fax:

DORMA Automatics, Inc. 924 Sherwood Drive Lake Bluff, Illinois U.S.A. Toll Free: Fax: ARCHITECTURAL SPECIFICATION ED-700 SECTION 08460 Automatic Entrance Doors DORMA Automatics, Inc. Series ED-700 (Surface Applied) LOW ENERGY OPERATING SYSTEM FOR SWINGING DOORS 1.01 SUMMARY: A. Section

More information

Full-featured operator with slim profile for moderate to high traffic applications LOW ENERGY OPERATOR CATALOG

Full-featured operator with slim profile for moderate to high traffic applications LOW ENERGY OPERATOR CATALOG Full-featured operator with slim profile for moderate to high traffic applications 6300 S E R I E S LOW ENERGY OPERATOR CATALOG INTRODUCTION The Norton 6300 Series Low Energy Operator offers a broad set

More information

One Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series

One Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and

More information

SECTION [ ] HIGH PERFORMANCE OVERHEAD HIGH SPEED DOORS. Display hidden notes to specifier. (Don't know how?

SECTION [ ] HIGH PERFORMANCE OVERHEAD HIGH SPEED DOORS. Display hidden notes to specifier. (Don't know how? SECTION 08337 [08 33 23.13] HIGH PERFORMANCE OVERHEAD HIGH SPEED DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1

More information

SECTION FIRST RESPONDER SERIES HEAVY DUTY PERSONNEL LOCKERS DEBOURGH MFG. CO. 10/15/2013

SECTION FIRST RESPONDER SERIES HEAVY DUTY PERSONNEL LOCKERS DEBOURGH MFG. CO. 10/15/2013 SECTION 10501 FIRST RESPONDER SERIES HEAVY DUTY PERSONNEL LOCKERS DEBOURGH MFG. CO. 10/15/2013 PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General

More information

Guide Specification SECTION VINYL WINDOWS

Guide Specification SECTION VINYL WINDOWS February 2018 3948 Townsfair Way, Suite 200 Columbus, Ohio 43219 Toll Free 800-746-6686 Website www.simonton.com Email archdetails@simonton.com Guide Specification Specifier Notes: This guide specification

More information

SECTION METAL LOCKERS

SECTION METAL LOCKERS SECTION 10 5113 METAL LOCKERS This section includes editing notes to assist the user in editing the section to suit project requirements. These notes are included as hidden text, and can be revealed or

More information

ROLLER SHADES. Operating Systems Brochure. Barberton, OH P: / F:

ROLLER SHADES. Operating Systems Brochure. Barberton, OH P: / F: Operating Systems Brochure Barberton, OH 44203 P: 330.983.0220 / F: 330.294.4121 OPERATING SYSTEMS STANDARD MANUAL SHADE A cord loop opens and closes the shade smoothly and evenly. A special clutch system

More information

Architectural Manual. Vinyl Windows & Patio Doors

Architectural Manual. Vinyl Windows & Patio Doors Architectural Manual Vinyl Windows & Patio Doors Style Line Series Vinyl Windows & Patio Doors Instructions on how to use this manual: This document has been designed for easy navigation and to quickly

More information

One Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series

One Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and

More information

Roller Shades CORD LOOP. Head Rail, Fascia and No Head Rail. Installation & Care Instructions

Roller Shades CORD LOOP. Head Rail, Fascia and No Head Rail. Installation & Care Instructions Roller Shades CORD LOOP Head Rail, Fascia and No Head Rail Installation & Care Instructions 152038 H 5/30/2017 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill, drill bits

More information

SECTION [ ] SECURITY GRILLES. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION [ ] SECURITY GRILLES. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 08333 [08 33 14] SECURITY GRILLES Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Upcoiling Security Grilles, manually operated. B. Upcoiling

More information

81870 Alside_24667 Alside 11/3/16 5:01 PM Page 2 80 Series

81870 Alside_24667 Alside 11/3/16 5:01 PM Page 2 80 Series 80 Series Alpine s 80 Series is the ultimate in vinyl window technology. Our heavy-duty vinyl frames combined with 1" insulated, Low-E glass, make these windows some of the most energy-efficient produced.

More information

SECTION METAL LOCKERS. A. ADAAG Americans with Disabilities Act, Accessibility Guidelines.

SECTION METAL LOCKERS. A. ADAAG Americans with Disabilities Act, Accessibility Guidelines. SECTION 10 51 13 METAL LOCKERS PART 1 GENERAL 1.01 SECTION INCLUDES A. Heavy Duty Welded Gear Lockers. B. Locker benches. 1.02 REFERENCES A. ADAAG Americans with Disabilities Act, Accessibility Guidelines.

More information

Installation Instructions Skylight FlexShades by Draper

Installation Instructions Skylight FlexShades by Draper Caution 1 Read entire procedure before installing. Keep instructions for future reference. 2 Tools needed for installation: Cordless drill/screwdriver, with flathead, phillips, and 1 /4" nut driver attachments

More information

Rollstar Shade Installation Instructions

Rollstar Shade Installation Instructions Rollstar Shade Installation Instructions All Lifting Systems Inside or Outside Mount Thank you for purchasing your new Rollstar shade. It has been custom-made from the highest quality materials to the

More information

University of Delaware

University of Delaware SECTION 23 36 00 _ SUMMARY PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Constant/Variable volume supply terminal units. 2. Fan powered terminal units. 3. Exhaust valves B. Related Sections: Section

More information

MechoShade Hardware Features and Specifications

MechoShade Hardware Features and Specifications MechoShade Hardware Features and Specifications MECHO /5 Standard Pocket Extended 1. Mounting Brackets The drive assembly, idle-end assembly, and center support systems are attached to an 1/8 in. (3mm)

More information

RIG-I-FLEX 140 SERIES CURTAIN TRACKS

RIG-I-FLEX 140 SERIES CURTAIN TRACKS RIG-I-FLEX 140 SERIES CURTAIN TRACKS Parts Included 140 RIG-I-FLEX CWANA code CORD OPERATED/MOTORIZED WALK-ALONG 140 (240) 140-R (240-R) 141 (241) 141-R (241-R) 142 (242) 142-R (242-R) STRAIGHT CURVED

More information

Clutch Operated FlexShade NEXD Window shade with heavy duty clutch and 3 hardware profile. Cassette option.

Clutch Operated FlexShade NEXD Window shade with heavy duty clutch and 3 hardware profile. Cassette option. INSTRUCTIONS INSTALLATION & OPERATION Overview - FlexShade Components Idler 1¼ Roller with Spline Atachment Clutch TOOLS REQUIRED Clutch PENCIL POWER DRILL Idler 1 Eliptical Hem Bar TAPE MEASURE LEVEL

More information

Aluminum Wood Double-Hung Windows

Aluminum Wood Double-Hung Windows Replacement Parts Table of Contents Exploded View... 38 Parts List... 39 Liners and Stops... 40 --- 41 Picture Glass Bead and Cutting Schedule... 41 Picture Glass... 42 --- 43 Sash Assembly... 44 --- 47

More information

ThermaSeal TM220 SECTIONAL OVERHEAD DOORS

ThermaSeal TM220 SECTIONAL OVERHEAD DOORS ThermaSeal TM220 SECTIONAL OVERHEAD DOORS ** NOTE TO SPECIFIER ** Raynor; commercial sectional overhead doors. This section is based on the products of Raynor, which is located at: 1101 East River Rd.

More information

SECTION COILING DOORS AND GRILLES

SECTION COILING DOORS AND GRILLES PART 1 - GENERAL 1.1 DESCRIPTION SECTION 08 33 00 1. Use this section only for NCA projects. 2. Delete between //---// if not applicable to project. Also delete any other item or paragraph not applicable

More information

Parking Control Equipment Vehicle Fare Collection Roadway Construction Roadway Equipment

Parking Control Equipment Vehicle Fare Collection Roadway Construction Roadway Equipment 11 12 00 Parking Control Equipment 11 12 33 Parking Gates 11 12 33.13 Lift Arm Parking Gates 34 52 00 Vehicle Fare Collection 34 52 33 Vehicle Fare Gates 34 71 00 Roadway Construction 34 71 13.19 Vehicle

More information

3948 Townsfair Way, Suite 200 July 2013 Columbus, Ohio Toll Free Website

3948 Townsfair Way, Suite 200 July 2013 Columbus, Ohio Toll Free Website 3948 Townsfair Way, Suite 200 July 2013 Columbus, Ohio 43219 Toll Free 800-746-6686 Website www.simonton.com E-Mail archdetails@simonton.com Product Guide Specification Specifier Notes: This product guide

More information

A. This Section includes ac, enclosed controllers rated 600 V and less, of the following types:

A. This Section includes ac, enclosed controllers rated 600 V and less, of the following types: SECTION 262913 600 VOLT ENCLOSED CONTROLLERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 0 Specification

More information

B. Fabricate in accordance with ASHRAE handbooks and SMACNA duct manuals. A. Submit in accordance with Division-1 and Section

B. Fabricate in accordance with ASHRAE handbooks and SMACNA duct manuals. A. Submit in accordance with Division-1 and Section SECTION 15910 DUCT ACCESSORIES PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract including General and Supplementary Conditions, Division-1 Specification Sections,

More information

SUGGESTED SPECIFICATIONS

SUGGESTED SPECIFICATIONS PART 1 - GENERAL 1.01 SCOPE A. Pumps to be supplied under this specification shall be of a severe duty, recessed cupped impeller design suitable for use in (SLUDGE, GRIT, ETC. APPLICATIONS) with a 20 year

More information

Ambassador ALUMINUM WINDOWS & DOORS FOR ALL SEASONS

Ambassador ALUMINUM WINDOWS & DOORS FOR ALL SEASONS Ambassador ALUMINUM WINDOWS & DOORS FOR ALL SEASONS THE REVOLUTION IS HERE. I N T E R N AT I O N A L W I N D O W CO R P O R AT I O N About Ambassador The name says it all. Representing International Window

More information

BUSWAY Low Voltage (Pow-R-Flex)

BUSWAY Low Voltage (Pow-R-Flex) BUSWAY LOW VOLTAGE (POW-R-FLEX) PART 1 GENERAL 1.01 1.02 SCOPE The Contractor shall furnish and install the busway system including all necessary fittings, hangers and accessories as specified herein and

More information

R. Manually Operated: Standard closure to be manually operated push up, pull down with removable retrieval rod as standard. The effort to raise or low

R. Manually Operated: Standard closure to be manually operated push up, pull down with removable retrieval rod as standard. The effort to raise or low 4.02 ROLLING SECURITY CLOSURE SYSTEM: Rolling Security Closure System: Curtain Design: Lexan Panel 2. Constructed of 3 on center extruded aluminum sections. Each section framed with continuous, double

More information

Solar & Roller Shades

Solar & Roller Shades STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades 1 2 3 4 5 Motivia Motorization Table of Contents Step 1 - Getting Started....3 Everything You Need A Smooth Set-Up We want you to love your

More information

Defender Mini Online Emergency Central Lighting Inverter (CLI) Technical Specifications

Defender Mini Online Emergency Central Lighting Inverter (CLI) Technical Specifications Defender Mini Online Emergency Central Lighting Inverter (CLI) Technical Specifications PART 1 GENERAL 1.1 SUMMARY A. The Defender Mini CLI specification describes a single phase, online, solid state Lighting

More information

HPFB. Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES.

HPFB. Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES. Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/ or putting undue pressure

More information

SECTION CENTRIFUGAL HVAC FANS

SECTION CENTRIFUGAL HVAC FANS SECTION 233416 - CENTRIFUGAL HVAC FANS 1. PART 1 GENERAL 1.1. RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SINGLE SLIDING WINDOW 1000 SERIES 4-1/2" FRAME SINGLE SLIDER LIFT OUT

SINGLE SLIDING WINDOW 1000 SERIES 4-1/2 FRAME SINGLE SLIDER LIFT OUT PERFORMANCE EVALUATION OF SINGLE SLIDING WINDOW 1000 SERIES 4-1/2" FRAME SINGLE SLIDER LIFT OUT For Dominion Doors & Windows Ltd. IN ACCORDANCE WITH: AAMA/WDMA/CSA 101/I.S.2/A440-11 AND A440S1-17 Report

More information

TRAC-LITES One Circuit Trac System TRAC SECTIONS & SYSTEM COMPONENTS R Series

TRAC-LITES One Circuit Trac System TRAC SECTIONS & SYSTEM COMPONENTS R Series Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Reduced-profile, single-circuit trac sections for surface or pendant mounting. Compatible with a full range of feed, connector

More information

Product Guide Specification

Product Guide Specification October 2011 3948 Townsfair Way, Suite 200 Columbus, Ohio 43219 Toll Free 800-746-6686 Website www.simonton.com E-Mail archdetails@simonton.com Product Guide Specification Specifier Notes: This product

More information

SECTION OVERHEAD COILING SERVICE DOORS

SECTION OVERHEAD COILING SERVICE DOORS SECTION 08330 OVERHEAD COILING SERVICE DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word click on round Windows logo in top left

More information

SECTION SECTIONAL OVERHEAD DOORS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION SECTIONAL OVERHEAD DOORS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 08360 SECTIONAL OVERHEAD DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2006-2017 ARCAT, Inc. - All rights reserved ** NOTE TO SPECIFIER ** Raynor; commercial sectional

More information

SECTION MOTORS AND CONTROLS FOR WINDOW COVERINGS. Logo Display hidden notes to specifier by using Tools / Options / View / Hidden Text.

SECTION MOTORS AND CONTROLS FOR WINDOW COVERINGS. Logo Display hidden notes to specifier by using Tools / Options / View / Hidden Text. SECTION 12496 MOTORS AND CONTROLS FOR WINDOW COVERINGS Logo Display hidden notes to specifier by using Tools / Options / View / Hidden Text. ** NOTE TO SPECIFIER ** Somfy Systems, Inc.; motors for interior

More information

Product Guide Specification

Product Guide Specification July 2013 3948 Townsfair Way, Suite 200 Columbus, Ohio 43219 Toll Free 800-746-6686 Website www.simonton.com E-Mail archdetails@simonton.com Product Guide Specification Specifier Notes: This product guide

More information

Basic Switching Control Terminology and Information Guide

Basic Switching Control Terminology and Information Guide Basic Switching Control Terminology and Information Guide Low Voltage Modular Switch (recessed wall installation) Available with drapery motors only. A specially designed three button switch, open-stop-close,

More information

600 SERIES STANDARD DUTY STRAIGHT TRACK INSTALLATION INSTRUCTIONS

600 SERIES STANDARD DUTY STRAIGHT TRACK INSTALLATION INSTRUCTIONS 600 SERIES STANDARD DUTY STRAIGHT TRACK INSTALLATION INSTRUCTIONS PLEASE READ INSTRUCTIONS THOROUGHLY BEFORE BEGINNING. A. BI-PARTING TRAVEL 1. Before raising track into position, determine location of

More information

Glydea Range. High Performance Motorization Solutions for Draperies

Glydea Range. High Performance Motorization Solutions for Draperies Glydea Range High Performance Motorization Solutions for Draperies G l y d e a E x p a n ds Y o u r Opp o r t u n i t i e s Today, drapery motorization is becoming the standard for hotel rooms, meeting

More information

AAMA/WDMA/CSA 101/I.S.2/A440-08

AAMA/WDMA/CSA 101/I.S.2/A440-08 PERFORMANCE TESTS IN ACCORDANCE WITH AAMA/WDMA/CSA 101/I.S.2/A440-08 Product Manufacturer: Report No.: AI-04016-U1 Rev.1 ACRYLON PLASTICS 122 PAQUIN ROAD WINNIPEG, MANITOBA R2J 3V4 204-669-2345 Report

More information

Roller Shade Installation Instructions

Roller Shade Installation Instructions Roller Shade Installation Instructions Standard Installation p - 2 - Cordless Installation p - 6 - Cassette Installation p - 10- Motorization Solar Panel Installation p - 12 - Motorization Remote Control

More information

** NOTE TO SPECIFIER ** Overhead Door Corporation; High performance overhead coiling door products.

** NOTE TO SPECIFIER ** Overhead Door Corporation; High performance overhead coiling door products. Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2016 ARCAT, Inc. All rights reserved ** NOTE TO SPECIFIER ** Overhead Door Corporation; High performance overhead coiling door

More information

5830 Skylight, Solar Smart Retrofit Installation

5830 Skylight, Solar Smart Retrofit Installation Introduction The Solar Smart has a mounting bracket that allows the operator to rotate slightly to reduce wear and tear on the chain drive system for greater performance and reliability. Because of this

More information

PDI PowerWave 2 Bus System

PDI PowerWave 2 Bus System 1 GENERAL 1.1 Summary This specification covers the electrical characteristics and general requirements for a continuous opening, low voltage, vertical or horizontal power busway distribution system. System

More information

SECTION AXIAL HVAC FANS

SECTION AXIAL HVAC FANS SECTION 233413 - AXIAL HVAC FANS 1. PART 1 GENERAL 1.1. RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

START HERE GRILLE REMOVAL. 1) Turn off engine and chalk tires with stop block. Open Hood. 1. Disconnect negative battery terminal.

START HERE GRILLE REMOVAL. 1) Turn off engine and chalk tires with stop block. Open Hood. 1. Disconnect negative battery terminal. GRILLE REMOVAL & Grille Installation Guide Parts included (1) LASER TORCH - Main Part #7315711 (1) LASER TORCH STEALTH - Main Part #7315711-BR (1) 30 LED Light Bar (1) Power Cable Wiring Harness Hardware

More information

Solar Roller & Classic Roller Shades

Solar Roller & Classic Roller Shades STEP BY STEP INSTALLATION INSTRUCTIONS Solar Roller & Classic Roller Shades 1 2 3 4 5 Motivia Motorization Table of Contents Step 1 - Getting Started....3 Everything You Need A Smooth Set-Up We want you

More information

SECTION HIGH-SPEED ROLLING DOORS. B. Wiring from electric circuit disconnect to operator to control station.

SECTION HIGH-SPEED ROLLING DOORS. B. Wiring from electric circuit disconnect to operator to control station. 08-03-16 Rytec Turbo-Seal Insulated Model Number TS6000-INS Architectural Specifications SECTION 083000 HIGH-SPEED ROLLING DOORS PART 1 GENERAL 1.01 SECTION INCLUDES A. High-speed roll up doors. B. Wiring

More information

F. VAV hoods shall have a restricted bypass plate.

F. VAV hoods shall have a restricted bypass plate. 1.01 SUMMARY A. Section Includes: 1. Laboratory fume hoods. B. Related Sections: 1. Section 6500 Laboratory casework 2. Section 15 Mechanical: Furnishing and installation of plumbing utilities and final

More information

Roller Shade Section Effective December 1, 2014

Roller Shade Section Effective December 1, 2014 Roller Shade Section Effective December 1, 2014 Save a life: "Install Safety Devices!" Roller Shade Measuring & Ordering Instructions Selecting the Type of Mounting: Determine whether the blind is going

More information

Sonoran Roller Shade

Sonoran Roller Shade Sonoran Roller Shade Retail Price List Effective March 1st, 2018 Product Information Product Specifications Pattern Listing Pricing Motorization Options Terms, Conditions and Warranty Page 2 Page 3 Page

More information

Juno Trac-Master Trac Lighting Systems. Comprehensive line and low voltage track systems

Juno Trac-Master Trac Lighting Systems. Comprehensive line and low voltage track systems Juno Trac-Master Trac Lighting Systems Comprehensive line and low voltage track systems Juno Trac-Master System Safe and simple installation is what you can expect from Juno one-circuit and two-circuit

More information

BTX Drapery Systems. General Overview

BTX Drapery Systems. General Overview BTX Drapery Systems General Overview BTX is THE supplier for drapery systems. Whether your clients are looking for large, curved, customized, or complicated products, or something that s extremely user-friendly,

More information

Caslan Roman Shade Section

Caslan Roman Shade Section Caslan Roman Shade Section Effective June 6, 2011 Patented Cords Free Roman Shade Now Available! Patent No. D 636.204 Save a life: "Install Tension Safety Devices!" Caslan Roman Shade Measuring Instructions

More information

PROJ. NO SECTION HYDRONIC PUMPS

PROJ. NO SECTION HYDRONIC PUMPS SECTION 23 21 23 HYDRONIC PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Cobra 3 Stand-By Emergency Central Lighting Inverter (CLI) Technical Specifications

Cobra 3 Stand-By Emergency Central Lighting Inverter (CLI) Technical Specifications Cobra 3 Stand-By Emergency Central Lighting Inverter (CLI) Technical Specifications PART 1 GENERAL 1.1 SUMMARY A. This specification describes a stand-by, three-phase, solid state Lighting Inverter System

More information

Fortress 1 Outdoor Emergency Central Lighting Inverter (CLI) Technical Specifications

Fortress 1 Outdoor Emergency Central Lighting Inverter (CLI) Technical Specifications Fortress 1 Outdoor Emergency Central Lighting Inverter (CLI) Technical Specifications PART 1 GENERAL 1.1 SUMMARY A. This specification describes a single phase, on-line, double conversion, solid state

More information

Two Circuit Trac System TRAC SECTION, JOINERS & FEEDS

Two Circuit Trac System TRAC SECTION, JOINERS & FEEDS Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single

More information

Solar & Roller Shades

Solar & Roller Shades STEP BY STEP INSTALLATION INSTRUCTIONS Solar & Roller Shades Loop Control, Loop Control with Cassette/2 on 1 Headrail & Loop Control with Metal Valance Table of Contents Step 1 - Getting Started....3 Everything

More information

START HERE GRILLE REMOVAL. 1) Turn off engine and chalk tires with stop block. Open Hood. 1. Disconnect negative battery terminal.

START HERE GRILLE REMOVAL. 1) Turn off engine and chalk tires with stop block. Open Hood. 1. Disconnect negative battery terminal. Parts included (1) X-Metal - Main Part #6715791 (1) Stealth X-Metal - Main Part #6715791-BR (1) Laser X-Metal - Main Part #7715891 (1) Laser Stealth X-Metal - Main Part #7715891-BR (1) Universal X-Metal

More information