Bitumen and Petroleum Testing Equipment

Size: px
Start display at page:

Download "Bitumen and Petroleum Testing Equipment"

Transcription

1 GATHA Enterprises A n I SO Company Bitumen and Petroleum Testing Equipment Penetrometer with Transfer Dish PENETROMETER WITH BATH FOR BITUMEN & TAR(Analog Version) Penetrometer with bath for Bitumen &Tar Test : As per IS: 1203/1978 Use: Used for the determination of penetration of asphaltic bitumen and fluxed asphalt and blown type bitumen, Petroleum wax & jelly. Description: Bath Unit consists of container of 20cm (H) x20cm (W) x35cm (L) Argon welded, needle, SS Cup 55mmdiax35mm (H) 8No. Transfer dish4no., Water bath Inner of SS304 and outer powder coated finish with motorized stirrer cum pump and a flange type hot+cold zone immersion SS304 heater of 1.5 Kw rating to maintain desired temp. Temp. Range: 0 C-95 C, having cooling & heating arrangement controlled by a Digital Temperature controller cum indicator with PT-100 Sensor, Continuous duty Kirloskar compressor for cooling, electrically operated DC 230V plunger, penetration indicator between 225&350, Needle with 50 gms. and 100 gms. weights and timing device. Digital penetrometer for direct readout of penetration having Encoder & Decoder arrangement with digital timer 9.9 sec Max. The whole unit is mounted on castor wheels for easy movability. Microprocessor based unit provides automatically timed operator programmable penetration measurements Conforms to all ASTM, IP, ISO 9001 and related specifications Unit tests the consistency of lubricating greases, petroleum waxes, bitumens, pastes, creams and other solid to semisolid products, including a variety of food products. Microprocessor control provides a full range of measurement and reporting options The penetrometer defaults to the standard ASTM interval of 5 seconds, or the operator may program a different interval in the range between 0.1 and seconds. All selected parameters are retained in memory and automatically repeated in subsequent tests until changed by the operator. Penetration measurements in the full range of in 1/10 mm scale are reported in either 1/10 mm or 1/100 mm increments at the operator s option. If a test result falls outside of the programmed range, an audible signal and visual error message alert the user of a failed sample. Results can be communicated to a printer or computer via a built in interface. Illumination with magnifying glass is also provided. Fine adjustment of the tip of the needle is also provided. Leveling indicator is also given. Built in DC operated Plunger is also incorporated with UNIT.Power:230V50Hz BASIC MANUAL (DIAL TYPE) PENETROMETER(With all standard accessories)(standard accessories includes Needle, Cone with Needle,50/100gms wts,plates, Cylindrical Container, Sample Container) SS Bath (with Heating/cooling) digital temp. controller PT-100 Sensor for bath, transfer dish(8nos),pump cum Stirrer-( Only Dig PID Microprocessor Controller with AUTOTuned type for Bath Temp Control, Range +2*C to 98*C ) BASIC Manual PENETROMETER WITH BATH (heating) digital temp. controllerpt-100 Sensor for bath, transfer dish(8nos),pump cum Stirrer and Spring loaded needle & std accessories)( Only Dig PID Microprocessor Controller with AUTO Tuned type for Bath Temp Control ) DIGITAL PENETROMETER WITHOUT BATH but with Electrically Operated DC Plunger& All std accessories,illumination, Magnifying glass, Leveling tube DIGITAL PENETROMETER (with Electrically Operated DC Plunger& All std accessories,illumination, Magnifying glass, Leveling Tube) WITH BATH (heating/cooling), digital temp. controller PT-100 Sensor for bath, transfer dish(8nos),pump cum Stirrer. OPTION: Communication port with PC/PRINTER interface & DATA-LOGGER

2 Manual Penetrometer: As per IS: 1448[P 93]:1979 / IS: 1203:1978 / ASTM D / ASTM D 217. The Universal Penetrometer is employed for testing a wide variety of materials as measured by penetration of weighted needles or cones. Main applications are for bituminous materials, but waxes, greases, foods, and pharmaceuticals are among other products tested. Penetration is read from a 5" (127mm) diameter indicator dial of divisions, each representing 0.1mm of penetration. Global offers heavy-duty units for manual and automatic use and a lighter, portable model for field work or for users with limited work load or limited budget. All meet ASTM and IS standards when fitted with proper needle or cone. The unit is ruggedly constructed for accurate, sensitive measurements. The aluminum base has a machined, grooved table with leveling screws for fine adjustments of tips of needles, cones and a spirit level. A robust stainless steel rod act as a support guides for a cast aluminum head with coarse adjustments & a movable table with rotating knob for fine adjustments to level the meniscus of specimen and a calibrated friction-free plunger mechanism. Indicator dial has instant zero reset. Any needle or cone with standard 1/8" (3mm) diameter stem may be mounted to the 47.5g plunger assembly. A standard 2.5g needle and two additional loading weights (50g, 100g) are included. Needles or cones for other tests can be provided separately as needed. Overall dimensions are 10.5x13x22" (267x330x559), (W x D x H) approx. The Automatic model is the same as the manual unit, but has a button release mechanism with digital timer & DIGITAL read out for penetration to automatically stop the plunger when the preset time from 0.1 to 9.9 sec. expires with audible buzzer sound. The penetration needle for bituminous materials is smooth, hardened, tempered stainless steel with brass ferrule and weighs 2.5g to give 50g total when mounted. Stainless steel wax penetration needle is also 2.5g but has truncated coneshaped tip with approx. 4mm maximum diameter tapered to 0.15mm diameter end. several types of 102.5g grease cones as having polished 90 cone with 30 removable hardened steel tip are available. Standard accessories includes: 1no spring loaded Plunger, 1no each wts of 50 & 100gm, 1no of Needle, 1no Sample Container (Manual Unit including all standard accessories) & Calibretion Extra for Electrically operated Plunger for release of needle/cone. Extra for Digital Timer. POWER: 230V,50 Hz(If opted for Electrical Plunger & Dig.Timer with Buzzer Alarm) CONES, NEEDLES AND ACCESSORIES: Use with Digital/Manual Pentrometer to determine the consistency of petroleum products, wide range of penetration types are available ( also for non-petroleum samples,see below). (For Grease) (For Bitumen) (For Grease) (For Wax) Optional: (If required additional) 1. Weights of 50/100 gms, duly chrome plated and slotted for loading. 2. Hardened needle as per IS standard, GC 2131 per needle. For GC 2121 (HOLLOW CONE of BRASS duly Nichal/Chrome Plated weighing 2.5gms) per needle 3. Brass solid cone as per IS standard. (Used only for Wax/Grease penetration GC 2141/2142)) 4. SS container As per IS STD (35 mm Ht. x 56 mm Dia.) for bituminous sample. 5. SS /Brass Chrome Plated Cylindrical Container As per IS STD with inside thread for Wax 6. SS/Brass Base Plate Chrome plated As per IS STD for Wax 6. Provision for Illumination with magnifying glass 7.. SS Standard Block for Calibration Purpose of Penetrometer (5mm,10mm,15mm,20mm) 8... Dimensional Calibration Charges extra for accessories For Cone, For rest

3 Cloud and Pour Point Apparatus: As per IS: 1448 and ASTM D97/66-IP 15/67 and ASTM D 2500/66-IP 219/67. The unit is designed to meet the test method as per above standards. It is used to carry tests of any petroleum oils as per above test methods. The bath is triple walled in construction with inner chamber made up of stainless steel and exterior of GI sheet with epoxy powder coated finish with PUF insulation in between. The unit has four compartments four different temperature ranges as follows: 1st Compartment: -1 C to +2 C. 2nd Compartment: -17 C to +18 C. 3rd Compartment: -35 C to +32 C. 4th Compartment: -47 C to +51 C. The top surface of unit is of Bakelite thick sheet for easy cleaning. Each compartment has 4 test jackets made up of cylindrical flat bottomed glass/copper of 45 mm diameter x 115 mm height. Test jar made up of clear cylindrical glass with flat bottom ( mm diameter x mm height). All the four compartments have individual cooling system which includes hermetically sealed Kirloskar compressor; 4- digital microprocessor based digital temperature controllers with PT-100 sensors. Power Input: 230 V, 50 Hz, 1-phase supply. Note: 1. Single compartment unit is available (for 4 Cup) Temperature. -35 C to +32 C 2. Double compartment unit is available (for 8 Cup) Temperature -17 C to +18 C & -47 C to +51 C, 3. Triple compartment unit is available (for 12 Cup) Temperature -1 C to +2 C -35 C to +32 C & -47 C to +51 C Temperature range of up to -74 C is available (Price on request). Kinematic Viscosity Bath ASTM D 445 ; IP 71 ; DIN ; ISO 3104 ; IS1206 Highly stable viscosity bath temperatures. Digital measurement and display. The Viscosity Bath is designed to simplify ASTM D 445; IS-1206 kinematic viscosity testing. A top-mounted controller keypad permits quick entry of bath set point temperature while a sophisticated microprocessor PID Auto tuned controller controls the bath heating and stirring through flange top mounted motorized pump cum stirrer. To further enhance the input, the unit accommodates up to a maximum of six individual capillaries. The HVB features a measuring range of 5ºC to 200ºC and can be used with mineral oil, silicone oil, or water as the bath base media. Bath temperature is displayed on a bright, easy-to-read digital display. In addition, the unit features a built-in over-temperature circuit protection Features: Accommodates up to six capillary tubes; optional Cannon-Fenske or Canon- Menin tube holders available Measures kinematic viscosity of petroleum products/any oils at temperatures from 20ºC to 150ºC, according to ASTM D 445; IP 71 ; DIN ; ISO 3104 ; IS-1206 Controls bath temperature with ±0.01ºC stability & resolution of ±o.1 C Digital bath temperature measurement and display Large capacity bath with built-in stirrer cum PUMP, & illumination by Daylight CFL fluorescent tube Integral over-temperature protection through SSR. SS Ball Valve provided for ease of Drain.

4 The unit has a double walled construction with outer GI /MS powder coat finish & argon welded inner of SS 304, having glass wool insulation between the walls. A motorized Pump with Stirrer is provided for better temperature uniformity. Toughened glass window from both sides with fluorescent tube for easy visualization. The SS immersion heater (Hot + COLD Zone Type) does the heating. PID Auto tuned Microprocessor based Digital temperature controller cum indicator controls the process temperature. Cooling of bath is achieved by CFC free hermetically sealed Compressor & direct copper tubing inside the inner area for fast & accurate cooling. Internal dimensions(lxwxd) Capacity Ltrs. Heating: 1. 45x20x30 cms for 5 C above ambient to C. 4VM 25 Ltrs x20x30 cms for 5 C above ambient to C 6VM 35 Ltrs. Cooling: 3. 45x20x30 cms for 5 C to 95 C 4VM 25 Ltrs x20x30 cms for 5 C to 95 C 6VM 35 Ltrs. Note: The above price is without Clamp, U Tube & Bath media. OPTIONAL: 1. Auto Heater Cut-off with Liquid Level Solid State Audio-Visual Watch Dog Electronic Circuit with Free potential SS304Magnetic Float Valve 2. U tube clamp made up of acrylic polycarbonate material; 3. Glass U tube of any type; (with our calibration certificates) 4. On demand Software based Microprocessor programmable PID controller with Time proportionate bands, data logger & cyclic timer, real clock battery backup, RAM memory, printer & PC interface Modbus RTU Compatible can be provided with the unit at Extra cost. Our technology is fully controlled, easy to handle, user friendly, intelligent and reliable. (We are coming out shortly with AUTO VISCO BATH to Measure & Display DIRECT READING of viscosity in centipoises for the loaded specimen. The price-band includes as below) Particle Charge Apparatus Particle charge apparatus As per IS 8887, Anex:'E": Use: For measuring the cationic or anionic nature of the bituminous products. Description: Unit consists of battery, rheostat, milliammeter, 2 - SS electrode plates, glass container, illumination for the chamber, timer device (all provided in required / specified dimensions and parameters). Mains / battery operated. The instrument is well illuminated with fluorescent lamp for better view of sample &deposition on SS plate. It operates on 12vsupply either on mains or battery through ON/OFF switch. Digital power supply gives current greater than 4mA. A mechanical timer of 30Minutes Rating helps to set Time duration of deposit. Particle Charge Apparatusfor Cationic/Anionic ONE SPECIAL DIGITAL LED TO JUDGE ANIONIC/CATIONIC WITH OUT CLEANING/OBSERVATION OF SS PLATES

5 Frass Breaking Point Apparatus for CRMB Test Fraass Breaking point Apparatus : As per IS: Use: This apparatus is used for the determination of fraass breaking point of solid and semisolid bitumen. Description: The Unit consists of mould press, bending apparatus (made of brass as per required / specified dimensions), plaque (as per required / specified dimensions), cooling apparatus only (made of glass without cooling compressor), digital temp indicator with PT100 sensor, and plate and stand. Fraass breaking point is the temperature at which bitumen first becomes brittle as indicated by the appearance of cracks when a thin film of the bitumen on a metal plaque is cooled & flexed in accordance with the specified conditions. The apparatus consists of bending apparatus, plaque specimen made up of spring steel 41 mm long x20mm width & 0.15 mm thick, cooling apparatus (as per detail) made up of glass jars as per given specification(no external cooling device),digital temp. Indicator and mould press for uniform thickness of bitumen specimen on plaque.the whole instrument is fixed on a CRCA powder coated plate. DUCTILITY APPARATUS AS PER IS (DIGITAL DUCTILE READ-OUT) Ductility apparatus: As per IS : (Only Heating Version, Ambient to 95*C) Use: Used for the determination of ductility of distillation residue of cut back bitumen, blown type bitumen and other bituminous products. Description: Unit consists of inner SS304 argon welded water bath & outer CRCA duly epoxy power coated finish with heating arrangement controlled Ductility Apparatus by digital temp. Controller with PT100 sensor to maintain desired temp.the pump is used as agitator arrangement for uniformity of water temperature. The cold water can be poured / drained by drain valve with additional intake. The IS specified CRMB test is carried by this m/c.the special feature of this m/c are: The Two speeds of displacement viz.50 mm/min & 10 mm/min can be achieved by 3 positions Toggle switch only. Auto forward / Zero set start / Reverse displacement is done by single switch. The displacement can be read directly from digital displacement indicator in mm. (OPTION:In Dig Ductility) Digital timer & displacement drive with digital displacement indicator is coupled as per demand of test. (OPTION:In Dig Ductility) C.R.M.B. IS Specified Brass Mould. NOTE: The above prices are for HEATING type only above ambient temperature. For COOLING cum HEATING PRICE ON REQUEST C.R.M.B IS SPECIFIED BRASS MOULD - (For 3 set) DIGITAL DUCTILITY M/C Microcesor Software Based(With Direct Dutility Reading, Reverse or Forward Measure): MANUAL ANALOG DUCTILITY M/C WITH SCALE/THERMOSTASTIC TEMP. CONTROL FOR WATER-BATH/MOTOR.

6 RING & BALL SOFTENING POINT APPARATUS: Ring and Ball softening point apparatus: As per IS: Use: Used for the determination of softening point of asphaltic bitumen and fluxed native asphalt, road tar, coal tar pitch and blown type bitumen. Suitable for bitumen & bituminous binders, filler aggregates used in bituminous mixtures, binders for paints and varnishes and resins derived from naval stores. Description: Unit consists of steel balls and brass rings as per IS specified dimensions, ball guide for ball centering, support for the ring(2no), all Ring & Ball Softening point mounted in a beaker which is provided with magnetic stirrer and a Immersion apparatus heater to heat the liquid inside. Temperature is maintained with the help of a programmable digital temp. Controller provided with PT100 sensor to achieve 5 degree C/min. temperature rise, by ramp rate setting. The whole assembly is fitted on a powder coated plate for better accessibility. (With 600ml Borosilicate Beaker Bath for preconditioning) (Semi Auto Model) Fully Auto Detection (by locking the Softening Point Temperature) & Display it on Alphanumeric LCD Display with Microprocessor Program Controller {with Pc operation/printer interface VISCOSITY BY SAYBOLT FUROL AS PER IS 3117:1965 Use: Used for the determination of viscosity of the bitumen/asphalt specimen. Description: Unit consists of oil tube (as per specified / required dimensions and made of corrosion resistant metal), water bath and manual stirring apparatus, digital Auto tuned PID temp. controller cum indicator, with PT100 sensor for accurate measurement of temperature(resoklution of 0.01*C, timing device (digital timer circuit) and graduated glass receiver. The instrument is basically used to cover the standard of physical & chemical requirements of bitumen emulsion (Anionic type) for roads. The apparatus consists of oil tubes made entirely of brass material as per specified dimension.the oil tube is housed in a cylindrical SS bath with electrical heating coil & manual stirring arrangement & timer.a receiver flask of 60ml is kept at bottom just below Drain of oil tube.a sprit level is given along with the apparatus to maintain the perfect level of whole instrument.the instrument is mounted on a powder coated CRCA platform for easy accessibility & the base is illuminated to have clear vision of receiver flask..by following the test procedure laid down in above standard gives perfect result.for measuring viscosity by say bolt furol method. Calibrated Auto Tuned PID controller with PT-100 sensor & resolution of 0.01*C - Extra. DIGITAL TIMER WITH BUZZER - Extra. RECEIVER 60ML FOR ABOVE - Extra. Spare Plated Brass Oil Tube(Without Heater) Spare Heater

7 LOSS ON HEATING APPARATUS:AS PER IS: Loss on heating apparatus: As per IS: Use: Used for the determination of loss on heating of asphaltic bitumen's. Description: Unit consists of inner SS chamber & outer MS powder coated finish with heating SS finned U type arrangement controlled by digital temperature controller cum indicator with PT100 sensor for maintaining desired temp. One perforated metal shelf made of aluminum with rotating shaft rotating at constant speed 5rpm, Digital timing device coupled with the digital temp controller cum indicator, and cylindrical metal container with flat bottom in specified dimensions. Air circulation with motorized blower for uniformity of temperature inside the chamber. Loss on Heating Temp range: Ambient to 199.9*C Automatic Flash & Fire point Apparatus: Determination of the Flash- and Fire-Point with Open Cup - Cleveland Method (automatic) AS PER IS 1448( P-69 ) :1969, ASTM D 92/66, IP 6/57 Scope The flash point is the lowest liquid temperature at which application of the flame causes the vapors of the test specimen of the sample to ignite. To determine the fire-point, the test is continued until the application of the test flame causes the test specimen to ignite and sustain burning for a minimum of 5s. This flash point and fire-point test method is a dynamic method and depends on definite rates of temperature increases to control the precision of the method. Its primary use is for viscous materials having a flash point below79 C (175 F) except fuel oils, to define the hazards of flammable and combustible materials used in shipping and safety regulations. The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash point is approached. At specified intervals a test flame is passed across the cup, to measure the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions. It is an automatic flash and fire-point tester used to examine liquid as well as highly viscous samples in the same instrument without any additional equipment for temperature range up to 400*C. For substances with unknown flash points, the APPARATUS has a special search mode program. During the entire heating period, the test flame is moved across the sample at suitable intervals. The expected flash point of a specimen can thereby be found in a time saving and economical manner. Optional On demand: When examining highly viscous specimens, a preheating time and temperature are set, in order to warm-up and liquefy the sample & to insert temperature sensor probe without problem. Further a skimmer is provided for removing the surface skin from bituminous samples. The UNIT is equipped with: Standard Cup: with handle, made of brass Temperature Probe Pt-100: for sample temperature Battery operated (1.5V pencil type cell) Gas Igniter: for LPG gas ignition (Manually operated) Flame Detection Unit: for the detection of flash- and fire-points by UVsensor. Heating: By electrical SS Tubular Cartridge Heater of suitable rating to maintain ramp rate & easily replaceable. Flame Arrest Cover for extinguishing the fire in the cup DC Motors: Flame movement, LID Open/Close, Assembly of sensor RTD(Pt-100 thermocouple) Up/Down mechanism

8 PC Interface Programmed Controller The Unit is incorporated with MODBUS RTU PC interface Microprocessor based PID Programmable controller user friendly features. (PC operated system through RS232 cable connection as option at extra cost) Specification & Features: Automatic Flash and Fire point apparatus (By Cleveland Open Cup Method). Temp.Range: Ambient to 400 C with RTD sensor as Thermocouple. Flame-Detector: UV based flame-detector sensor & Controller. DC motors: Flame movement, LID Open/Close, Assembly of sensors Up/Down mechanism. Controller: Microprocessor based Programe process controller cum indicator with 3-wire RTD temperature sensor, free potential flame detector sensor as i/p and DC V SSR as o/p. Equipment Overall Size (LxWxH): 24 x14 x31 Equipment Gross Weight: 21 Kg. Supply: 230 V, 1-ø, 50 Hz supply with proper earthing system for Controller. Flash- and Fire-Point with Open Cup - Cleveland Method (manual) AS PER IS 1209:1978 COC FLASH & FIRE POINT TEST APP. Product - Flash Point For Bitumen User: Bitumen, Insulating Oil, Lube Oil, Power Plant, Engine Oil, Hydraulic Fluid, Turbine Oil, Jet Lube, Regulatory Authorities This flash-point and fire-point test method is a dynamic method and depends on definite rates of temperature increases to control the precision of the method. Its primary use is for viscous materials having a flash-point between 79 C (175 F) and 400 C (752 F) except fuel oils, to define the hazards of flammable and combustible materials used in shipping and safety regulations. The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash-point is approached. At specified intervals a test flame is passed across the cup, to measure the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions. The flash-point is the lowest liquid temperature at which application of the flame causes the vapors of the test specimen of the sample to ignite. To determine the fire-point, the test is continued until the application of the test flame causes the test specimen to ignite and sustain burning for a minimum of 5s. Manual Flash- & Fire-Point Tester, Cleveland Method Consisting of: special tripod stand, heating collar, insulating board, spl rubber tubing, hose connection, universal gas merker burner, thermometer holder Technical Data: Temperature range: +79 C to +400 C Supplied with: 1 cup with handle, 1 thermometer

9 Flash- and Fire-Point with Open Cup - Cleveland Method (semiautomatic AS PER IS 1448 (P:69)-1997, ASTM D-92/66, IP 6/67 Product: Flash Point for Petroleum Products Users: Petroleum Product mfgrer except fuel oils This flash-point and fire-point test method is a dynamic method and depends on definite rates of temperature increases to control the precision of the method. Its primary use is for viscous materials having a flash-point below79 C (175 F) except fuel oils, to define the hazards of flammable and combustible materials used in shipping and safety regulations. The temperature of the approximately 70 ml test specimen is increased rapidly at first and then at a slower constant rate as the flash-point is approached. At specified intervals a test flame is passed across the cupmanualy, to measure the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions. The flash-point is the lowest liquid temperature at which application of the flame causes the vapors of the test specimen of the sample to ignite. To determine the fire-point, the test is continued until the application of the test flame causes the test specimen to ignite and sustain burning for a minimum of 5s. Semi-Automatic Flash- & Fire-Point Tester, Cleveland Method Consisting of: stainless steel housing, electric heater, Digital Auto tuned Single Ramp rate Temp controlled with PT-100 Thermocouple and hose connection, spl rubber tubing for LPG Gas, Burner Nozzle with Hand operating System, Sample cup Technical Data: Temperature range: Ambient to 400 C Supplied with: 1 cup with handle, 1 spare Heater, Power supply: 230 V, 50Hz Flash-Point with Closed Cup/Open Cup - Pensky-Martens Method - (manual) AS PER IS ( Method A ), IP-34, ASTM D-93, IS 1448 (P-21 ) Product: Flash Point for Bitumen Application: Testing of Bitumen, Biodiesel, Fuel, Lube Oil, Power Plant, Jet Fuel, Turbine Fuel, Engine Oil, Turbine Oil, Solvent, Regulatory Authorities, Paint, Varnish, Mastics Flash-point determination of petroleum products using: Method A: for fuel oils, lubricating oils and other homogeneous liquids. (For Temp Range: -10*C to +60*C)( MANUALLY OPERATED) Method B: for non-homogeneous materials like mixtures of liquids & solids, cutback bitumen s, surface-film building liquids or liquids with a viscosity above 5.5 cst at 40*C. (Ambient to +110*C) (SEMI AUTOMATIC Electrically Heated with PID AUTO TUNED MICROPROCESSOR Digital Temp Controller) Method C: for Open type Pensky Martens with higher Flash/Fire temp range like biodiesel oils, mineral oils, silicon oils escaroles. (Ambient to + 350*C) Manual Flash-Point Tester, Pensky Martens Method (A): Features: - easy to manipulate Supplied with: 1 cup with Handle 1 cover with spring operated Rotating Shutter 1 Tripod Stand with Doom as Air-bath 1 thermometer 1 Hand Operated Stirrer with Flexible shaft 1 Pilot Gas Jet for Flame 1 Gas Burner

10 Technical Data: Temperature range: approx. -10 to +60 C(Method A) Semi-Automatic METHOD B Pensky-Martens Close Cup:Electrically Heating Model & concealed FHP Stirrer for Uniform Heating & Stirring & with Built-in Microprocessor based AUTO TUNNED PID DIGITAL Temperature Indicator cum Controller coupled with PT-100 Sensor as thermocouple, Supplied with: Brass Test Cup with insulated Handle, Tripod Stand with Doom as Air- bath, Electrical heating with concealed FHP Stirrer for cup coupled with Dig PID Auto Tuned Microprocessor Temp Controller cum Indicator, Pilot Gas test Jet Assembly for introduction of LPG test Gas jet manually. (Method B Semi Automatic without Flame Sensor & LPG Flame Auto Sampling / movement) Method C : Automatic version for Open type Pensky Martens with higher Flash/Fire For Temperature range- Ambient to + 350*C, use of COC (Cleveland Open Cup) AUTOMATIC Version is recommended, as the rest of the version is same. Double wall Hot Air Ovens: Construction: The unit is Laboratory type, with a double walled construction. The Inner Chamber is made of Stainless Steel (SS-304) 22G. The outer chamber is made of GI/CRCA, with powder coated finish in two tone color (Stainless Steel Buffed finished outer chamber can also be provided on request). Glass wool insulation of 65mm is present in between the walls to avoid heat dissipation. The Control panel is located at the top of oven.the heater compartment is at the bottom & is made up of Long lasting SS304Tubular Heater with HOT+COLD Zone junction & the Lead wire is taken out of Oven coupled with cover for safety. A Flush door fitting coupled with virgin silicon square rubber gasket of 15mm & special lock and handle arrangement for locking the door is provided for perfect sealing of chamber. The Tray is made of GI mesh, Crimped and of size ¾ x12g wire thickness with stainless steel Border. The spacing between the shelves is 4.16 A,3 pin molded power cord for 230V,50Hz supply is provided. Temp.Range: 5 C above ambient to 250 C. Heating process Controls: The unit is controlled by a Auto tuned Micro-processor based ON/Off PID; Single set point temperature controller cum indicator with built in digital timer ( As option ) and PT-100 sensor. An Audio-Visual Alarm to indicate the End of cycle is included in the system( If TIMER is provided with UNIT ). A 15A, 4Pole heavy duty Contactor/SSR output is also provided. Optional: a. A Motorized Forced Air Circulation by blower motor arrangement on back wall of oven for uniformity of temp of the inside chamber. b. On demand Software based Microprocessor programmable PID controller with Time proportionate bands, data logger & cyclic timer, real clock battery backup, RAM memory, printer & PC interface controller with PT- 100 sensor can be provided with the unit at Extra cost. Our technology is fully controlled, easy to handle, user friendly, intelligent and reliable. c. Digital Timer for above(either built-in OR separate) Size(DxWxH) No. oftrays Rating KW x12 x x14 x x18 x x18 x X24 X x24 x

11 GMP-GC-15: Laboratory Hot-Plate Rectangular: Construction: The heating plates are rectangular in shape and made up of MS Cast Iron plates with Groves for Heating Coil (SS Plate can also be provided on request).the top plates overhang by supporting MS pillar which allows air insulation between plate and control Compartment to keep it cool. Long lasting Nicrome Heating wire with ceramic Beads are used for the heating process. A choice of Energy Regulator / Digital Temperature controller/thermostat is provided. Max Temp: 350 C. Thermostatic control for above Digital temperature controller with Fe-Con Thermocouple Sensor for above Muffle Furnace of up to 1200 C: Laboratory muffle Furnace of Max temp: 1200 C. Working temp: 1150 ºC. Construction: The unit has an outer body made up of MS with epoxy powder coat finish & a door with a heat resistant handle. The unit has a double walled type construction with the muffles body at centre of the furnace & the control box at top with 1"solid spacer in between. A coil type Heater of Kanthal/Nichrothal wire wound on the muffle with cerewool blanket serves as the heating element. A brick insulation+ ceramicwool +high density mineral wool insulation of 4" is also given to have skin temp.of furnace less than 50 C. The door is provided with heavy-duty hinges and latch-catch lock system to open/close the furnace. Control panel: It is located at the top of furnace and includes a Auto tuned PID Microprocessor based temperature controller cum indicator with Cr/Al Thermocouples controls heating process.power:230v or 440V, 50 Hz as per requirements. Control will be SSR output type. Safety Fuse with MCB for power is also provided. Muffle size Size Rating Kw DxWxH 1. 9 x4 x x5 x x6 x x9 x9 6.5 OPTION : On demand Software based Microprocessor programmable PID controller with Time proportionate bands, data logger & cyclic timer, real clock battery backup, RAM memory, printer & PC interface controller with Cr-Al thermocouple sensor can be provided with the unit at Extra cost. Our technology is fully controlled, easy to handle, user friendly, intelligent and reliable. We can also supply Universal Testing Machines, Compression Testing Machines, Tensile Testing Machines, Chain and Rope Testing Machines, Spring Testing Machines, Vickers / Brinell / Rockwell Hardness Testing Machines, Dynamic Balancing Machines, Dynamic Hardness Testers, Impact Testing Machines, Torsion & Fatigue Testing Machines & Special purpose Material Testing Machines, etc. We reserve the rights to change the above specifications without any notice due to constant improvements in design GATHA Enterprises An ISO Company 3,Snehdeep Apts, Chintamaninagar, Sahakarnagar No.2,Pune INDIA Tel : Mobile : Fax: gatha@vsnl.net, gathaent@dataone.in, gathaent@gmail.com

Penetration. Test Methods

Penetration.   Test Methods Test Methods Penetration of Bituminous Materials ASTM D5; IP 49; DIN 52010 Cone Penetration of Lubricating Grease ASTM D217; IP 50; ISO 2137; DIN 51804; FTM 791-311, FTM 791-313 Cone Penetration of Petrolatum

More information

U tube viscometer. Kinematic viscosity bath RASAYAN

U tube viscometer. Kinematic viscosity bath RASAYAN Viscosity The viscosity of a fluid is a measure of its resistance to gradual deformation by shear stress or tensile stress. For liquids, it corresponds to the informal notion of "thickness". For example,

More information

PMA 5. Pensky-Martens Flash Point Tester. ::: Volatility... Flammability

PMA 5. Pensky-Martens Flash Point Tester. ::: Volatility... Flammability PMA 5 Pensky-Martens Flash Point Tester ::: Volatility... Flammability A Tradition of Competence 140 years of developing, producing and supporting excellent flammability instruments. 140 years of technology

More information

Instruments for Chemical and Petroleum Products. Flash Point

Instruments for Chemical and Petroleum Products. Flash Point Instruments for Chemical and Petroleum Products Flash Point A Tradition of Competence 140 years of technological advances lie between the first flash point tester and today s Anton Paar product line of

More information

Environmental/Analytical LabCivil Engineering Lab Equipment

Environmental/Analytical LabCivil Engineering Lab Equipment DIGITAL PH METER Display : 3.5 Digit LED. Range : ph 0 to 14.00, mv 0 to ± 1999. Resolution : ph 0.01, mv 1. : ph ± 0.01, mv ± 1 mv. Temp. Compensation : Auto 0 to 100 deg. C., Manual 0 to 100 deg. C.

More information

ASTM D4. Bitumen Content Qty. Model Description. Related Standards: ASTM D370, E177

ASTM D4. Bitumen Content Qty. Model Description. Related Standards: ASTM D370, E177 ASTM D4 Related Standards: ASTM D370, E77 Bitumen Content H-550 Bitumen soluble in organic solvents set H-550. Gooch crucible H-550.2 Crucible holder H-550.3 Buchner funnel H-550.8 Glass fiber filter H-255

More information

Foaming of Lubricating Oils (manual)

Foaming of Lubricating Oils (manual) Foaming of Lubricating Oils (manual) ASTM D 892, ASTM D 6082 sequence IV, ISO 6247, DIN 51566, IP 146, JIS K2518, BS 5092 (obs.) Product group(s): User group(s): Scope: Lubricant Testing Automotive, Engine

More information

ASTM D4. Bitumen Content Qty. Model Description. Related Standards: ASTM D370, E177

ASTM D4. Bitumen Content Qty. Model Description. Related Standards: ASTM D370, E177 ASTM D4 Related Standards: ASTM D370, E77 Bitumen Content H-550 Bitumen soluble in organic solvents set H-550. Gooch crucible H-550.2 Crucible holder H-550.3 Buchner funnel H-550.8 Glass fiber filter H-255

More information

Safety drying ovens. Advantages: Areas of application: FDL series 115

Safety drying ovens. Advantages: Areas of application: FDL series 115 FDL series 115 Safety drying ovens Safety drying ovens The BINDER FDL with silicone and dust-free inner chamber, as well as symmetric airflow dries specimens containing solvents perfectly and thus meets

More information

GLASSCO LABORATORY EQUIPMENTS PVT. LTD.

GLASSCO LABORATORY EQUIPMENTS PVT. LTD. PROGRAMMED FOR PRECISIO N GLASSCO LABORATORY EQUIPMENTS PVT. LTD. STAINLESS STEEL TOP Magnetic Stirrer with Hotplate - Analog Aluminium Moulded Construction Easy temperature & Stir controls Installed with

More information

Manual Kinematic Viscosity Bath Tamson TV12

Manual Kinematic Viscosity Bath Tamson TV12 Manual Kinematic Viscosity Bath Tamson Rev 1.05 1 Viscosity Business Today Testing kerosene Testing diesel Testing lubricants Testing fuel oils Testing residues Testing bituminous or asphalt samples Testing

More information

Cassia Siamia BLOOD BANK REFRIGERATED CENTRIFUGE MP 6000 R. Technical Data (MP 6000 R)

Cassia Siamia BLOOD BANK REFRIGERATED CENTRIFUGE MP 6000 R. Technical Data (MP 6000 R) BLOOD BANK REFRIGERATED CENTRIFUGE The range of Blood component separation equipment and Hi-Volume Centrifuges are designed for Blood bags, large capacity centrifuge tubes and bottles. These centrifuges

More information

product manual H-1240 & H F Electric Penetrometer with Digital Automatic Timer

product manual H-1240 & H F Electric Penetrometer with Digital Automatic Timer 07.09 product manual H-1240 & H-1240.4F Electric Penetrometer with Digital Automatic Timer Introduction The Humboldt Electric Automatic Penetrometer is of rugged construction, but requires careful handling

More information

Safety drying ovens with expanded temperature range

Safety drying ovens with expanded temperature range MDL series 115 Safety drying ovens Safety drying ovens with expanded temperature range The BINDER MDL, with enhanced control function, works at temperatures up to 350 C (662 F). It is it perfectly suited

More information

Safety drying oven with expended temperature range

Safety drying oven with expended temperature range MDL series 115 Safety drying ovens Safety drying oven with expended temperature range The BINDER MDL 115 with enhanced control function works at temperatures up to 350 C. This safety drying oven meets

More information

Instruments for the Analysis of Petroleum Products. Oxidation Stability

Instruments for the Analysis of Petroleum Products. Oxidation Stability Instruments for the Analysis of Petroleum Products Oxidation Stability What is Oxidation Stability? Oxidation stability describes the resistance of a material towards oxygen. This is a basic requirement

More information

ISO 9001, ISO1400, ISO13485, CE and WHO-GMP certified.

ISO 9001, ISO1400, ISO13485, CE and WHO-GMP certified. ISO 9001, ISO1400, ISO13485, CE and WHO-GMP certified. Environmentally friendly Ultra Deep Freezer, -40 degree powered by Meditech Technology for safe storage. Stable Temperature Control Temperature is

More information

Heating chamber with mechanical convection

Heating chamber with mechanical convection FED series 240 Drying ovens / Heating ovens Heating chamber with mechanical convection The multi-talented BINDER heating chamber of the FED series provides almost unlimited capacity and is particularly

More information

Heating chamber with mechanical convection

Heating chamber with mechanical convection FED series 720 Drying ovens / Heating ovens Heating chamber with mechanical convection The multi-talented BINDER heating chamber of the FED series provides almost unlimited capacity and is particularly

More information

Special Provision No. 111S12 July 2017

Special Provision No. 111S12 July 2017 AMENDMENT TO OPSS 1103, NOVEMBER 16 Special Provision No. 111S12 July 17 OPSS 1103, November 16, Material Specification for Emulsified Asphalt, is deleted in its entirety and replaced with the following:

More information

Instatherm ACE. The Safest Heating Method! Eliminate the need for heating tapes, immersion heaters and heating mantles.

Instatherm ACE. The Safest Heating Method! Eliminate the need for heating tapes, immersion heaters and heating mantles. ACE For Glass Vessels Borosilicate Glass Fused-to-Glass Conductive Heating Film Integral Outer Insulation Instatherm The Safest Heating Method! Eliminate the need for heating tapes, immersion heaters and

More information

Integrated temperature test and calibration bench Model CBS-SC4000

Integrated temperature test and calibration bench Model CBS-SC4000 Calibration technology Integrated temperature test and calibration bench Model CBS-SC4000 WIKA data sheet CT 92.33 Applications Testing and calibration of temperature measuring instruments such as: - Mercury

More information

Instatherm ACE. The Safest Heating Method! Eliminate the need for heating tapes, immersion heaters and heating mantles P.

Instatherm ACE. The Safest Heating Method! Eliminate the need for heating tapes, immersion heaters and heating mantles P. ACE For Glass Vessels Borosilicate Glass Fused-to-Glass Conductive Heating Film Integral Outer Insulation Instatherm The Safest Heating Method! Eliminate the need for heating tapes, immersion heaters and

More information

Refrigerated incubator with Peltier technology

Refrigerated incubator with Peltier technology KT series 53 Incubators and cooling incubators Refrigerated incubator with Peltier technology The KT series combines outstanding performance with impressive energy efficiency and environmental friendliness.

More information

For the fastest possible service, you can now reach Koehler via the Internet. On our website, you can:

For the fastest possible service, you can now reach Koehler via the Internet. On our website, you can: For the fastest possible service, you can now reach Koehler via the Internet. On our website, you can: Locate the test instrument you need based on your desired ASTM method. Download product information.

More information

Heating oven with mechanical control

Heating oven with mechanical control ED series 23 Drying ovens / Heating ovens Heating oven with mechanical control The strength of the BINDER ED series heating oven: routine drying and sterilization applications up to 300 C. Thanks to the

More information

Heating chamber with mechanical convection

Heating chamber with mechanical convection FED series 53 Drying ovens / Heating ovens Heating chamber with mechanical convection The multi-talented BINDER heating chamber of the FED series provides almost unlimited capacity and is particularly

More information

TESIGNG OF FUELS: VISCOSITY OF LIQUID FUELS

TESIGNG OF FUELS: VISCOSITY OF LIQUID FUELS Department of Mechanical Engineering Indian Institute of Technology New Delhi II Semester -- 2017 2018 MCL 241 Energy systems and Technologies TESIGNG OF FUELS: VISCOSITY OF LIQUID FUELS 1. Introduction

More information

Heating chamber with mechanical convection

Heating chamber with mechanical convection FED series 53 Drying ovens / Heating ovens Heating chamber with mechanical convection The multi-talented BINDER heating chamber of the FED series provides almost unlimited capacity and is particularly

More information

MDL series Safety drying ovens with first class safety features and an expanded temperature range

MDL series Safety drying ovens with first class safety features and an expanded temperature range Safety drying ovens MDL series Safety drying ovens with first class safety features and an expanded temperature range The MDL series operates at temperatures up to 350 ºC at an airflow of 400l/min, ideal

More information

The Safest Heating Method!

The Safest Heating Method! ACE Instatherm For Glass Vessels The Safest Heating Method! Borosilicate Glass Eliminate the need for heating tapes, immersion heaters and heating mantles. Instatherm is a safer, more precise heating method

More information

LAB EQUIPMENTS. Manufacturing & Servicing of:

LAB EQUIPMENTS. Manufacturing & Servicing of: Manufacturing & Servicing of: LAB EQUIPMENTS OVERHEAD STIRRER MAGNETIC STIRRER LAB OIL BATH LAB OIL BATH WITH MAG. STIRRER TEMPERATURE CONTROLLER MULTI CHANNEL TEMP. INDICATOR LAB CENTRIFUGE We Service

More information

Petroleum Testing Equipment

Petroleum Testing Equipment Petroleum Testing Equipment www.koehlerinstrument.com BOHEMIA, NEW YORK HOUSTON, TEXAS Worldwide Support Providing quality testing instrumentation and technical support services for research and testing

More information

PETROLEUM TESTING EQUIPMENT N-WISSEN 2016

PETROLEUM TESTING EQUIPMENT N-WISSEN 2016 ` PETROLEUM TESTING EQUIPMENT N-WISSEN 2016 N-Wissen products range includes the following petroleum testing and measuring equipment: ASTM D 5 - D 217 Digital penetrometer for bitumens; ASTM D 5 - D 217

More information

Technosys Blood Bank Refrigerator

Technosys Blood Bank Refrigerator Technosys Blood Bank Refrigerator BBR-350 Bags BBR-250 300 Bags Shelves of BBR Handle of BBR The chamber is to be constructed in double wall. The interior of the chamber is to be made of Stainless Steel

More information

DEPARTMENT OF CHEMICAL ENGINEERING University of Engineering & Technology, Lahore. Energy Engineering Lab

DEPARTMENT OF CHEMICAL ENGINEERING University of Engineering & Technology, Lahore. Energy Engineering Lab DEPARTMENT OF CHEMICAL ENGINEERING University of Engineering & Technology, Lahore Energy Engineering Lab Introduction Energy is often defined as the capacity to do work. Several different forms of energy,

More information

DMS-9202, Asphaltic Concrete Patching Material (Stockpile Storage)

DMS-9202, Asphaltic Concrete Patching Material (Stockpile Storage) Overview Effective Date: July 1999 July 2004 This specification shall govern for an asphaltic concrete mixture intended primarily as a cool to cold weather stockpile patching mix for maintenance. It shall

More information

Geotechnical Testing Equipment

Geotechnical Testing Equipment asphalt equipment production Asphalt is a sticky, black and highly viscous liquid or semi-solid that is present in most crude petroleum. It is most commonly used in road construction. The material consists

More information

POWER. Switch opening. Enter/Exit Menu Menu Scroll Increase/Decrease Setpoint GCE SERIES MODEL 10AFE MODEL 20AFE

POWER. Switch opening. Enter/Exit Menu Menu Scroll Increase/Decrease Setpoint GCE SERIES MODEL 10AFE MODEL 20AFE CMW MANU STOP TUNE Quincy Lab, Inc. Model AFE Digital Series Lab Ovens With Microprocessor Control & Digital Display OPERATING MANUAL Standard Contents (1) AFE Series Lab Oven (2) Adjustable chrome wire

More information

MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT

MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 1103 NOVEMBER 16 MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT TABLE OF CONTENTS 1103.01 SCOPE 1103.02 REFERENCES 1103.03 DEFINITIONS 1103.04

More information

fax

fax INDUSTRIAL THERMOMETERS Industrial thermometers Selecting the correct thermometer for an application is by definition very important, to achieve the maximum accuracy and repeatability of the temperature

More information

Heating oven with natural convection

Heating oven with natural convection ED series 23 Drying ovens / Heating ovens Heating oven with natural convection The strength of the BINDER ED series heating oven: routine drying and sterilization applications up to 300 C. Thanks to the

More information

Climate chamber with illumination

Climate chamber with illumination KBW series (E5.1) Climate chambers with illumination Climate chamber with illumination The BINDER climate chamber with illumination of the KBW series achieves homogeneous light distribution with its natural

More information

TESTING OF FUELS : FLASH AND FIRE POINT

TESTING OF FUELS : FLASH AND FIRE POINT Department of Mechanical Engineering Indian Institute of Technology New Delhi II Semester -- 2017 2018 MCL 241 Energy systems and Technologies TESTING OF FUELS : FLASH AND FIRE POINT 1. Introduction The

More information

Closed Cup Flash Point Tester

Closed Cup Flash Point Tester www.labtron.com info@labtron.com We have distinguished ranges of Closed Cup Flash Point Tester especially designed to offer highest level of accuracy and quality giving a versatility in the capacity and

More information

Heating oven with mechanical convection

Heating oven with mechanical convection FD series 53 Drying ovens / Heating ovens Heating oven with mechanical convection A BINDER FD series heating oven is always used when fast drying and sterilization is required. Thanks to its fully homogeneous

More information

Climate chambers with illumination

Climate chambers with illumination KBW series (E5.1) Climate chambers with illumination Climate chambers with illumination The BINDER KBW series climate chamber with illumination achieves homogeneous light distribution and ensures consistent

More information

Water Baths & Shaking Water Baths. Quality Technology for Routine Applications

Water Baths & Shaking Water Baths. Quality Technology for Routine Applications Water Baths & Shaking Water Baths Quality Technology for Routine Applications 94 Water Baths and Shaking Water Baths The TW and SW Water Bath Series are microprocessor-controlled, durable, and long-lasting

More information

Incubators. Incubators

Incubators. Incubators Incubators Stuart has a number of incubators specially designed for accurate and reproducible temperature controlled applications. All incubators have state of the art microprocessor detection, setting

More information

SECTION B ASPHALT BITUMEN PAVETEST

SECTION B ASPHALT BITUMEN PAVETEST SECTION B ASPHALT BITUMEN PAVETEST Bituminous mixture, also known as asphalt mixture, is mainly composed by aggregates and bitumen, an infinite variety of mixtures being possible. This section is divided

More information

ISO-9001:2008 HOT PLATES CATALOG. Phone: Fax: Web:

ISO-9001:2008 HOT PLATES CATALOG. Phone: Fax: Web: ISO-9001:2008 HOT PLATES CATALOG Phone: 281 496 0900 Fax: 281 496 0400 Email: sales@expotechusa.com Web: www.expotechusa.com 32 Digital Feature international symbols for easy recognition by all operators

More information

AKVdiesel. Automated kinematic Viscometer key features. Fully complies with ASTM D445. Two measuring positions. Remove cap and pour in sample

AKVdiesel. Automated kinematic Viscometer key features. Fully complies with ASTM D445. Two measuring positions. Remove cap and pour in sample Suitable for measuring gas oils, distillate fuels and diesel fuels, as specified in ASTM D975, EN590 and ISO 8217 (marine fuels). The RHEOTEK AKV-diesel is a fully automated viscometer system suitable

More information

Shaking Incubators & Shakers

Shaking Incubators & Shakers Shaking Incubators & Shakers Bench Top Shaking Incubator LBSI Series Bench Top Shaking Incubator provides a controlled environment for continuous growth of biological organisms. LBSI Series has a wide

More information

L U B R I C A N T S & MATERIALS

L U B R I C A N T S & MATERIALS PRODUCT GUIDE L U B R I C A N T S & MATERIALS TRUSTED BRANDS ERACHECK CFC-Free Oil-in-Water Testing by QCL-IR Technology Ultimate high-speed, precision solution for low, and sub- ppm concentrations of

More information

FECR. World Class Testing Equipments An ISO 9001 Certified co. Paper & Packaging Equipments

FECR. World Class Testing Equipments An ISO 9001 Certified co. Paper & Packaging Equipments FECR World Class Testing Equipments An ISO 9001 Certified co. Paper & Packaging Equipments Bursting Strength Testing Humidity Chamber / Conditioning Chamber Bursting Strength is reliable index of the strength

More information

General Apparatus. Petroleum Products Timers Clamps Frames Laboratory Jacks Set-up Frame Set.

General Apparatus. Petroleum Products Timers Clamps Frames Laboratory Jacks Set-up Frame Set. Set-up Frame Set Lab-Chron Timer Lab-Line presents a wide variety of high quality general laboratory apparatus to compliment our line of constant temperature products. Choose corrosion-resistant alloy

More information

PETROLEUM WAX & VASELINE PLANT

PETROLEUM WAX & VASELINE PLANT PETROLEUM WAX & VASELINE PLANT Seoul, Korea Q_iso s Activities OPTIMUM SOLUTION PROJECT MANAGEMENT FRONT-END ENGINEERING PROCESS & MECHANICAL ENGINEERING INSTALLATION & CONSTRUCTION OPERATION & MAINTENANCE

More information

HA Thickness Gauge IS:2386 (part 1)- 1963

HA Thickness Gauge IS:2386 (part 1)- 1963 AGGREGATE TESTING HA50.05 Mechanical Rotating Sample Divider (Motorised) IS : 1607-1960 For obtaining representative sample for sieve analysis. It is suitable for dry sands, fine powders, ores, refractory

More information

CEMENT TEST EQUIPMENTS

CEMENT TEST EQUIPMENTS CONTENTS CONTENTS Cement Compress on&flexural Test ng Mach ne 114 Jolt ng Table 123 Compress on J g Assembly 115 V brat ng Mach ne for 70.7 Cube Moulds 123 Flexure J g Assembly 115 Pluger Penetrat on Apparatus

More information

DMS-9203, Asphaltic Concrete Patching Material (Containerized)

DMS-9203, Asphaltic Concrete Patching Material (Containerized) Overview Effective Date: July 1999 July 2004 This specification shall govern for containerized asphaltic concrete mixture intended primarily for cool to cold, wet weather repair of small pavement areas.

More information

Date and Time of Pre Bid Meeting November 22, 2016 at a.m

Date and Time of Pre Bid Meeting November 22, 2016 at a.m Addendum No. 0 TENDER FOR SUPPLY, DELIVERY, INSTALLATION AND COMMISSIONING OF EQUIPMENT FOR LATEX TECHNOLOGY LABORATORY OF FACULTY OF ANIMAL SCIENCE AND EXPORT AGRICULTURE Tender No - UWU/B/C/6/09 Date

More information

MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT

MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 1103 NOVEMBER 07 MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT TABLE OF CONTENTS 1103.01 SCOPE 1103.02 REFERENCES 1103.03 DEFINITIONS 1103.04 DESIGN

More information

LUBRICATING GREASES. Test Methods

LUBRICATING GREASES.  Test Methods LUBRICATING GREASES s Page Evaporation Loss of Lubricating Greases and Oils ASTM D972, D2878; IP 183; FTM 791-351...148 Evaporation Loss of Lubricating Grease Over Wide Temperature Range ASTM D2595, D2878...149

More information

Products for Asphalt Testing

Products for Asphalt Testing Products for Asphalt Testing For over 50 years, CANNON Instrument Company has provided asphalt testing labs with critical testing equipment and reagents including viscometers, flash point testers, constant

More information

Section 4 DMS-9203, Asphaltic Concrete Patching Material (Containerized)

Section 4 DMS-9203, Asphaltic Concrete Patching Material (Containerized) Section 4 DMS-9203, Asphaltic Concrete Patching Overview Effective Date: August 2004 - December 2005. This Specification governs for rapid curing containerized asphaltic concrete mixture intended primarily

More information

PCU-200 Laboratory Viscometer

PCU-200 Laboratory Viscometer PCU-200 Laboratory Viscometer SIMPLE START-UP 1. Turn power on. Power switch is located on lower rear panel. Press door to open. 2. Using the SENSOR UP/DOWN controller, move sensor all the way up. 3. Slide

More information

industrial thermometers INDUSTRIAL THERMOMETERS

industrial thermometers INDUSTRIAL THERMOMETERS INDUSTRIAL THERMOMETERS industrial thermometers Selecting the correct thermometer for an application is by definition very important, to achieve the maximum and repeatability of the temperature reading.

More information

DMS ASPHALTIC CONCRETE PATCHING MATERIAL (STOCKPILE STORAGE)

DMS ASPHALTIC CONCRETE PATCHING MATERIAL (STOCKPILE STORAGE) DMS - 9202 (STOCKPILE STORAGE) EFFECTIVE DATES: AUGUST 2004 APRIL 2010. 9202.1. Description. This Specification governs for an asphaltic concrete mixture intended primarily as a cool to cold weather stockpile

More information

Stabinger Viscometer SVM 3001

Stabinger Viscometer SVM 3001 Stabinger Viscometer SVM 3001 Expect More Welcome to New Viscometry Measuring the viscosity of oils and fuels is all about certainty and compliance. Two approaches get you there: the traditional glass

More information

Flash Point Process Analyzer

Flash Point Process Analyzer Norms and standards ASTM D 56 ASTM D 93; DIN EN ISO 2719; IP 34 DIN EN ISO 13736; IP170 DIN 51755 Application The BARTEC BENKE Flash Point Process Analyzer (FPA-4) is a continuously measuring analyzer,

More information

Tender No. CL1 GEOTECHNICAL ENGINEERING LAB. CIVIL ENGINEERING DEPT.

Tender No. CL1 GEOTECHNICAL ENGINEERING LAB. CIVIL ENGINEERING DEPT. Tender No. CL1 GEOTECHNICAL ENGINEERING LAB. CIVIL ENGINEERING DEPT. I. EQUIPMENT/ASSESSORIES/GOODS FOR GEOTECHNICAL ENGINEERING LABORATORY A. LIST OF ITEMS &APPROVED MANUFACTURERS/SUPPLIERS Sr. No Equipment/Apparatus/Accessories/Goods

More information

Refrigerators/Freezers

Refrigerators/Freezers Explosion-Proof, Corrosion-Resistant Refrigerator Flammable Material Storage Refrigerator/Freezer Laboratory Freezer Lab-Line offers a complete line of refrigerators and freezers to accommodate virtually

More information

Tex-614-J, Testing Epoxy Materials

Tex-614-J, Testing Epoxy Materials Overview Effective: August 1999 May 2000. This method covers various test procedures for epoxy materials specified under the TxDOT Material Specification DMS-6100, Epoxies and Adhesives. The test to be

More information

SECTION 118 ASPHALT MATERIAL

SECTION 118 ASPHALT MATERIAL SECTION 118 ASPHALT MATERIAL 118.1 GENERAL REQUIREMENTS Transporting conveyances for asphalt material shall be free of contaminating material. A record of material hauled the previous load in truck transport

More information

Model 30GCE Low-Temp Oven POWER. Switch opening. View Setpoint Increase Setpoint Decrease Setpoint (3 sec.) Enter/Exit Menu Levels GCE SERIES

Model 30GCE Low-Temp Oven POWER. Switch opening. View Setpoint Increase Setpoint Decrease Setpoint (3 sec.) Enter/Exit Menu Levels GCE SERIES Model AFE - LT Low-Temp Series Ovens With Microprocessor Control & Digital Display OPERATING MANUAL Standard Contents (1) AFE Series Low-Temp Oven (2) Adjustable chrome wire shelf (4) Shelf brackets Model

More information

ISTEC MAGNETIC METERS

ISTEC MAGNETIC METERS ISTEC MAGNETIC METERS MEASURE ANY CONDUCTIVE LIQUIDS OR SLURRIES (EVEN ABRASIVE OR CORROSIVE) WITH THE NEW MICROPROCESSOR-BASED MAGNETIC METER -- A QUALITY PRODUCT - SIMPLE - RELIABLE - AT AN AFFORDABLE

More information

TECHNICAL CHARACTERISTICS: Structure : upright type, realized in sheet steel epoxy coated white colour both in- and outside or in stainless steel

TECHNICAL CHARACTERISTICS: Structure : upright type, realized in sheet steel epoxy coated white colour both in- and outside or in stainless steel TECHNICAL CHARACTERISTICS: Structure : upright type, realized in sheet steel epoxy coated white colour both in- and outside or in stainless steel 18/10 AISI 304 both in- and outside. All the internal corners

More information

Index for Labs under Civil Engineering

Index for Labs under Civil Engineering Index for Labs under Civil Engineering Sr. No. Laboratory Name 1 Applied Mechanics Laboratory- 1 2 Transportation Engineering Laboratory 3 Surveying Laboratory 4 Environmental Engineering Laboratory-2

More information

Mixer/Temperature Control

Mixer/Temperature Control Mixer/Temperature Control Dry Bath, Incubator, Shaker, Stirring Water Bath Major Science designs and manufactures a comprehensive range of mixing and temperature control equipments for use in the fields

More information

Temperature multi-function calibrator Model CTM

Temperature multi-function calibrator Model CTM Calibration Temperature multi-function calibrator Model CTM9100-150 WIKA data sheet CT 41.40 for further approvals see page 3 Applications Testing and calibration of all types of temperature measuring

More information

MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT

MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 1103 FEBRUARY 1996 MATERIAL SPECIFICATION FOR EMULSIFIED ASPHALT 1103.01 SCOPE 1103.02 REFERENCES 1103.03 Not Used 1103.04 Not Used 1103.05 MATERIALS

More information

Oregon Department of Transportation Standard Specifications For Asphalt Materials 2004

Oregon Department of Transportation Standard Specifications For Asphalt Materials 2004 Oregon Department of Transportation Standard Specifications For Asphalt Materials 2004 Effective for contracts and purchase orders advertised after January 1, 2004 Revisions - Changes to the 2003 Asphalt

More information

Model ED 400 Drying and heating chambers Classic.Line with natural convection

Model ED 400 Drying and heating chambers Classic.Line with natural convection Model ED 400 Drying and heating chambers Classic.Line with natural convection The strengths of a BINDER ED series drying chamber include routine drying and sterilization tasks up to 300 C. Thanks to the

More information

DMS-9202 Asphaltic Concrete Patching Material (Stockpile Storage or Bagged)

DMS-9202 Asphaltic Concrete Patching Material (Stockpile Storage or Bagged) Asphaltic Concrete Patching Material (Stockpile Storage or Bagged) Effective Date: May 2017 1. DESCRIPTION This Specification governs for crushed stone asphaltic concrete intended primarily as a cool-

More information

Model ED 400 Drying and heating chambers Classic.Line with natural convection

Model ED 400 Drying and heating chambers Classic.Line with natural convection Model ED 400 Drying and heating chambers Classic.Line with natural convection The strengths of a BINDER ED series drying chamber include routine drying and sterilization tasks up to 300 C. Thanks to the

More information

Thermo Scientific Hot Plates, Stirrers and Stirring Hot Plates

Thermo Scientific Hot Plates, Stirrers and Stirring Hot Plates Thermo Scientific Hot Plates, Stirrers and Stirring Hot Plates >> Performance, technology and safety Dependable Performance. Unmatched Safety. Exceptional Value. The success of your work demands precision

More information

INDIAN INSTITUTE OF TECHNOLOGY KANPUR Kanpur , Uttar Pradesh, India Centre for Lasers and Photonics

INDIAN INSTITUTE OF TECHNOLOGY KANPUR Kanpur , Uttar Pradesh, India Centre for Lasers and Photonics INDIAN INSTITUTE OF TECHNOLOGY KANPUR Kanpur 208016, Uttar Pradesh, India Centre for Lasers and Photonics Enquiry no.: CELP/RV/EQP/MHR/2017/1 Enquiry date: 23/04/2018 Closing date: 17/05/2018 Sealed quotations

More information

IKA Mixing Magnetic stirrers with heating

IKA Mixing Magnetic stirrers with heating with heating RET basic safety control RET basic C safety control RET basic safety control IKAMAG, RET basic C safety control IKAMAG with new heating and stirring technology for fast, accurate temperature

More information

Mineral Insulated Resistance Thermometers (RTD)

Mineral Insulated Resistance Thermometers (RTD) Mineral Insulated Resistance Thermometers (RTD) Electronic Temperature Measurement Data sheet : MIRTD/2012 Contents Page RTD Element Type 2 Conductors & Number of Wires 2 Probe Diameter 3 Length Types

More information

SECTION 916 (Pages ) is deleted and the following substituted: SECTION 916 BITUMINOUS MATERIALS

SECTION 916 (Pages ) is deleted and the following substituted: SECTION 916 BITUMINOUS MATERIALS 916 BITUMINOUS MATERIALS. (REV 7-28-03) (FA 1-13-04) (7-04) SECTION 916 (Pages 785-797) is deleted and the following substituted: SECTION 916 BITUMINOUS MATERIALS 916-1 Superpave PG Asphalt Binder: 916-1.1

More information

Short Form Catalogue AJ Thermosensors

Short Form Catalogue AJ Thermosensors Thermocouples Short Form Catalogue AJ Thermosensors Resistance thermometers Head mounted Probe style Application specific Accessories See the individual datasheets for more detailed information on each

More information

Manual Kinematic Viscosity Bath Tamson TV2000 & TV4000 ASTM D445, IP71, ISO 3104

Manual Kinematic Viscosity Bath Tamson TV2000 & TV4000 ASTM D445, IP71, ISO 3104 Manual Kinematic Viscosity Bath Tamson ASTM D445, IP71, ISO 3104 Rev 1.04 Viscosity Business Today Testing kerosene Testing diesel Testing lubricants Testing fuel oils Testing residues Testing bituminous

More information

A SURVEY OF OUR KNOW-HOW : PETROLEUM GLASSWARE VISCOMETER TUBES

A SURVEY OF OUR KNOW-HOW : PETROLEUM GLASSWARE VISCOMETER TUBES N O R M A L A B A N A L I S A SURVEY OF OUR KNOW-HOW : PETROLEUM GLASSWARE VISCOMETER TUBES NORMALAB ANALIS FRANCE S.A. 14, rue des Lilas 76210 LINTOT - FRANCE Tel : (33) 02 35 38 59 59 Fax : (33) 02 35

More information

OSU Rate of Heat Release Apparatus

OSU Rate of Heat Release Apparatus OSU Rate of Heat Release Apparatus THE BENCHMARK IN FIRE TESTING OSU Rate of Heat Release Apparatus FAR 25.853 (a-1), FAA Fire Test Handbook Chapter 5, ASTM E 906 Configuration A Standard Test Method for

More information

Model ED 720 Drying and heating chambers Classic.Line with natural convection

Model ED 720 Drying and heating chambers Classic.Line with natural convection Model ED 720 Drying and heating chambers Classic.Line with natural convection The strengths of a BINDER ED series drying chamber include routine drying and sterilization tasks up to 300 C. Thanks to the

More information

ASTM D Standard Specification for Biodiesel Fuel (B 100) Blend Stock for Distillate Fuels

ASTM D Standard Specification for Biodiesel Fuel (B 100) Blend Stock for Distillate Fuels ASTM D 6751 02 Standard Specification for Biodiesel Fuel (B 100) Blend Stock for Distillate Fuels Summary This module describes the key elements in ASTM Specifications and Standard Test Methods ASTM Specification

More information

Vessels and Distillation Equipment

Vessels and Distillation Equipment Vessels and Distillation Equipment 147 A suitable solution for practically every application in well-known BOLA-quality and optimally adapted to your needs. PRODUCT TIPS BOLA Scrubber Columns Pressure:

More information

DRAFT Jamaican Standard Specification for Bituminous materials

DRAFT Jamaican Standard Specification for Bituminous materials DRAFT Jamaican Standard Specification for Bituminous materials BUREAU OF STANDARDS Notice This is a draft standard and shall be used or referred to as a Jamaican Standard. It is subject to change without

More information

EBARA Submersible Propeller Pumps Contents Project: Model: Chk d: Date: Model

EBARA Submersible Propeller Pumps Contents Project: Model: Chk d: Date: Model Contents Model A0553 C1125 V0494 A0713 C1285 V0554 A0843 C1455 V0754 A03 C15 V0854 C1915 V0974 C2185 V1154 C2905 Section Page Specifications 3-3 Model Designation 3-6 Impeller Data 3-8 Material Specifications

More information

Standard Test Method for Dropping Point of Lubricating Grease 1

Standard Test Method for Dropping Point of Lubricating Grease 1 Designation: D 566 02 An American National Standard British Standard 2877 Designation: 132/96 Standard Test Method for Dropping Point of Lubricating Grease 1 This standard is issued under the fixed designation

More information