Installation Guide M9000. M9000 Controllers. Installation GUIDE M By Youngshin Electronics Co., Ltd.

Transcription

1 # Installation Guide M9000 Controllers M Installation GUIDE M9000 By Youngshin Electronics Co., Ltd.

2 1 2 TABLE OF CONTENTS M9000 Installation GUIDE 1. Installation Tips & Recommendations 2. M-9000 Wiring Digram 3. CN 1 4.CN2 5. CN 3 6. CN 4 7. CN 5 8.CN6 9.CN7 10. CN Transmitter Learning Routine 12. Option programming for Four Button Remotes 13. Option programming for Six Button(ONE WAY) Remotes 14. Diagnosing Problems with Auto-Start

3 3 4 Installation Tips & Recommendations 1-1. Please be careful not to lock yourself out. Pleaselowertheglasswindowsbeforeyoustartingtheinstallationincasethe doorlockswiththekeyinside.also,learntheremotetothebrainmoduleafter theinstallationhasbeencompleted Use Digital Multimeter for testing Usea Digital Multimeter foralltestingofwiresinthevehicle. Thisshouldbedoneonallwiresevenifyoufeelthatyouknowexactlywhatthey are and how they should test. Use of lamp tester may damage the electrical circuitofthevehicle Find Good Ground One of the most important wire connection is the connection to the ground. Pleasefindaspotthatdoesnothaveanyresistancetothebatteryground. Impropergroundwillresultinmalfunctionofthesystem. Organizing wiring after the installation Improper wiring organization will result in making noisy, connection problems, safety hazards. User s familiarity with operating manual Installershouldexplaintheuserthoroughlyaboutthesystemoperation Vehicle check-up prior to and after the installation. Foryourprotection,checkthevehicleinsideandoutincludingallofthe vehicle operating conditions and various factory systems to make sure they workproperlyafterinstallationinthesamemanneraspriortotheinstallation Make sure your installation does not become a driving hazard later to the driver. During installation process, please try to foresee there are any potential problemstothedriverlater. Potential Driving Hazards There should be no wiring around the brake. Connection problem or Insulation problem Please make sure all the connections are done by soldering and properlyinsulatedbytheelectricaltapes. Will any of your installation be affected by the vibration and engine heat during driving? Tiesecurelyeverycomponentsofyourinstallationbyuseofboltsor cabletie.becarefulnottodamageanywiringinsideofthe engine compartment by the engine heat.

4 5 6 M9000 Wiring Diagram

5 7 8 CN1 No 1 (White) : (+12V)Accessory Output Thiswirewillread (using your digital multi-meter) 0Vwiththekeyoff, and12vwiththekeyintheaccessoryor ON position. TheAccessorywirewillusuallydropoutduringcranking. Thiswiresupplies12Vtoclimatecontrolandotheraccessoriesinthevehicle andiscapableofsupplyingupto30a. Some vehicles do not have accessory wire - the ignition wire of such vehicles supply power to the accessories. Sodon tconnectthiswireforsuchvehicles. No 5 (Red) : (+)12V Constant Solderthiswiretothevehicle s12vconstant. This wire must be supplied power all of the time and must be able to with stand highcurrentdraw. No 6 (Violet) : (-)Ignition Output 1. Installation of the solenoid valve for Benz Engines Benz Vehicle has a vacuum hose underneath of the key ignition harness. The hose is vacuumed when engine starts with a key. To simulate this, asolenoidhastobeinstalledtocreatevacuumforremotestart. No 2 (Yellow) : (+12V)Start Motor Output Thiswirewillread(usingyourdigitalmulti-meter)12Vwhenthekeyisinthe crankposition.thiswiresuppliespowertothestartermotor. No 3 (Green) : (+12V)Ignition Output Thiswirewilltest(usingyourdigitalmulti-meter)0Vwiththekeyoff,and12V withthekeyinthe ON or RUN position. Theignitionwirewillnotdropoutduringcrankingofthevehicle. This wire supplies 12V to the ignition coil and other electrical systems needed forthevehicletorunproperly. No 4 (Black) : Chassis Ground Thiswillbetheoneofthemostimportantconnection. Connectthiswiretobaremetalofthevehicle. We do not recommend using the steering column for a grounding point. Makesureyoustripbackthepaintoruseafactorygroundingpoint. Badgroundingonthiswirewillbethebeginningoffuturetroubles. 2. Propane Gas Powered Vehicles Thereisagasvalveswitchforsuchvehicles.Forremotestart,thisswitchhas tobeturnedon.therearetwodifferenttypesofswitch.

6 9 10 Method1 : ParallelConnectionwiththe switch Method1 : Negative Trigger Door Lock System (W/O Actuator) Relay +12V power Door Switch 85 87a CN1-3 Diode CN Method2 : SerialConnectionwiththeswitch Gas Valve Gas Valve SW CN2-3(-) Ulock CN2-4(-) Lock Ulock Lock Factory Relay Door Connection EXT. (Positive) INT. (Negative) CN2 CN1-3 CN1-6 Relay No 1, No 2 (Violet) : Positive Signal Light Output 85 Connectthiswiretothe(+)signallightwireonthevehicle. Thiswirewillread (usingyourdigitalmulti-meter)eitheropenorgroundbeforethesignallight circuit is turned on and then it will read (+)12V after the signal light circuit is turnedon. No 3(Yellow) : Door Unlock Output No 4(Green) : Door Lock Output The following three door lock systems are the most common systems a Gas Valve SW Gas Valve Cut Method2 : Positive Trigger Door Lock System (W/O Actuator) CN2-3(+) Ulock CN2-4(+) Lock Method3 : ExternalActuator CN2-3 Ulock CN2-4 Lock Diode Door Switch Ulock Factory Relay External Actuator Lock (+)12V Door Connection EXT. (Positive) Door Connection EXT. (Positive) INT. (Negative) INT. (Negative)

7 11 12 No 5 (White) : (+)12V Siren Output TheBlackwireatthesirenistobechassisgrounded. The siren volume can be reduced by cutting the volume wire attached to the siren. No 6 (Black) : (+)12V Trunk Output Ifthevehicleisequippedwithelectricaltrunkrelease,thetrunkoutisconnected totriggerthetrunksolenoid.... Anti Jacking... (Ignition-Kill) Relay 85 CN a CN OFF ACC ON START Key Holder IgnitionWire CN1-3 Cut Engine trunk Release Switch CN2-6 trunk Solenoid No 2 (Yellow/Black) : Alternator sensing to monitor the engine running Thiswireistomonitorenginerunning. Locateasmallgaugewirefrom the alternator. When tested with your meter, it should show you about 2V when thekeyisonbutthevehicleisnotstarted. When the vehicle is started using the key, the wire should read about 14V. CN3... What is Noisy sensing... No 1 (Blue) : Negative Starter-Kill output Pleaseusethepre-wiredstarterkillrelay.... Anti Grinding... (Starter-Kill) Relay 85 CN1-3 CN a OFF ACC Cut ON START Key Holder StartWire CN1-2 A. Noisy Sensing When it is running, the engine generates sound and electrical noisy. Human ears recognize the engine running by sound but Magicar can recognize by electricalnoisy.ifyouselectthenoisysetting,youdonothavetoconnectthe alternatorsensingwire.thefactorydefaultsettingisnoisysensing withhighsensitivity- Switch1OffandSwitch2On. StartMotor

8 13 14 B. Potential Problem with Noisy Sensing Everyvehiclegeneratesdifferentlevelofelectricalnoisyandasamevehicle maygeneratesdifferentlevelofelectricalnoisyunderdifferentcircumstances. Insomecases,therefore,itwillbepossiblethatMagicarthinkstheengineis runningeventhoughonlyheaterfanisrunning. C. Dip Switch Setting Dip Switch #1 ON:Foravehiclethatgenerateshighlevelofelectricalnoisy. ThissettingwillreducethesensitivityofMagicar. OFF: Foravehiclethatgenerateslowlevelofelectricalnoisywhenengine isrunning FactorySetting. Dip Switch #2 O N : Noisy Sensing FactorySetting OFF: AlternatorSensing D. Noisy Sensing LED Please find the LED inside of the cover. The LED will come on when it senses electricalnoisybeyondpresetlevel. a. The LED should stay off until the starter cranks and come on steady when engine is running. Wait 2-3 minutes. If the LED stays on steady without any blinking,youaredone. b. IftheLEDcomesonbeforetheengineisrunning, shutofftheremote starting, turnonheswitch#1andtryremotestartingagain. TheLEDshould stayoffuntilthestartercranksandcomeonsteadyforthenext2-3minutes when engine is running. However, if the LED comes on again before the engine isrunning,ortheleddoesnotcomeonatall,ortheledlightblinkstimeto time while the engine is running, elect Alternator Sensing. Noisy Sensing does notworkforthisvehicle. Note 1 : For any diesel vehicles, we recommend you using Alternator Sensing. In case you are using Noisy Sensing for a diesel vehicle, please make sure you connect the glow plug wire. Note 2 : NoisySensingwillnotworkforavehiclethathasan alternatorproblem. No 3 (Red/Black) : Negative Trigger Door Open Sense E. Verifying Noisy Sensing IfyouareselectingNoisySensing,pleaseverifyifitworksproperlyasfollows No 4 (Red) : Positive Trigger Door Open Sense Step1.Disconnectthesirenwire. Step 2. Maximize the heater fan volume. Also, turn on radio and wind shield Dome Light Dome Light wipers Step 3. Leave the switch #1 Off, and #2 On. Step4.Tryremotestarting. +12V Door Trigger SW Door Trigger SW +12V CN3-3(-) Door Trigger CN3-4(+) Door Trigger Please make sure you have found a correct door sensing wire that monitors all doors.

9 15 16 No 5 (White/Black) : Negative Glow Plug Input No 6 (White) : Positive Glow Plug Input Ifyoudoníftconnectoneofthesewires(negativeorpositiveGlowsensing), thesystemwillactasgasolinevehicles. Only when one of these wires are connected, your system will know the diesel engine. The differences between gasoline and diesel engine are pre-heating time and the running time (15minutes for gasoline engine, 25minutes for diesel engines) when remote starting. No 9 (Black) : (-)Trunk Trigger Input Connect this wire to the trunk lamp wire as shown below. Trunk Lamp +12V CN 3-9 (-)TrunkTriggerInput +12V Glow Plug Lamp Engine Control Module Glow Plug Lamp Engine Control Module No 1 (Black) : (-) No 2 (Black/White) : (+) Temperature Sensor CN4 CN3-5 (-)Glow Plug Input CN3-6 (+)Glow Plug Input CN5 No 7 (Orange/Black) : Negative Parking Light Input No 8 (Orange) : Positive Parking Light Input No 1 (Black) : (-) No 2 (Blue) : Sense No 3 (Red) : (+) Shock sensor ParkingLight ParkingLight CN6 No 1 (Black) : (-) +12V CN 3-7 (-)ParkingLightInput ParkingLight controlrelay CN 3-8 (+)ParkingLightInput ParkingLight controlrelay No 2 (White) : Sense No 3 (Red) : (+) No 4 (Yellow) : LED Remote Pager sensor

10 17 18 Pager Location Transmitter Learning Routine CN7 No 1 (Yellow) : RX No 2 (White) : TX No 3 (Red) : (+) No 4 (Net wire) : (-) Antenna Ass y 1. Most vehicles Step #1: Cycletheignitionkeyfromtheoff positiontotheonpositionandback3times WITHIN 3 SECONDS thus giving the Green wire(harness#1) 12V3times. Whenthisprocedureisdonethesignallightswillflashonetimetoconfirm that you are in the valet/programming mode. Step #2: Once in the valet/programming mode and within 6 seconds, press Button I fora second.theparkinglightswillflashonce(andtherelayinside thecontrollerwillclickonce)toconfirmthatstep#2wascompleted. The antenna have been calibrated for horizontalinstallationatthetopcornerof thewindshield.differentinstallationmay affectthetransmittingdistancequiteseriously. CN8 No 1 (Yellow) : AUX 1 Antenna Location No 2 (Yellow/White) : AUX 2 AUX Output Step #3: Pressbutton I onthenewremotetoteachittotheunitwithin3seconds ofstep#2. Theunitwillacceptupto3remotes. Eachtimewhentheunit haslearnedaremote,theparkinglightswillflashonce(andtherelay insidethecontrollerwillclickonce)toconfirmtheprogrammingofthe remotes. Ifyoulearnonly1remote,Pressbutton I ofoneremoteforthreetimesso thatanyofthepreviouslearningisdeleted. Ifyoulearn2remotes, pressbutton I ofthefirstremotetwotimesand pressbutton I of the second remote one time. Theparkinglightswillflashtwice(andtherelayinsidewillclicktwice)to confirm the completion of the programming. The Various exterior devices are controlled by using of AUX output. A selection of four output types is available with option 2-4 & 2-5.

11 Benz types of vehicles that have vacuum hose underneath the ignition key box. Follow the same steps of the above 1, except that you use button I I I instead ofbutton I. The vehicle has a programming of automatic self-unlock when you turn off the engine with a key. So, in this case you have to choose this Bentz type option programmed locks doors upon remote-running end. The controller generates a negative relay output fortherelaythatcontrolsthevacuumhose. 3. Propane Gas Powered Vehicles Follow the same steps of the above 1, except that you use button IV instead ofbutton I. Option Programming for Four Button Remotes Step1 : For Programming menu 1: Key on,engine off, then Press Buttons (I+II) for2seconds. For Programming menu 2: Key on,engine off, then Press Buttons (I+IV) for2seconds. Thecarwillchirponceindicatingthatyou are in programming mode. Step2 : Within a 4 seconds afterpressing (I+II) or (I+IV),pressButton IV the number of times to go to the option number you want to change. You have to hear a chirp and see the parking light flash each time when you press Button IV. Step3 : Wait a few seconds. You will hear a number of chirps and see a number of parking light flashes corresponding to the option number youwanttochange. Ifthenumberofchirpsorflashesisnotwhat youwant, gobacktostep1. Step4 : Press Button I forthedefaultfactorysettingsandyourcarwill respond by one chirp and one flash. Press Button II forthe optionalsettingandyourcarwillrespondbytwochirpsandtwo parkingflashes. If you hear a long chirp, you are going out of programming mode, please go back to Step1. If you want to change more options, go back to Step1. Resetting all of Menu #1 or Menu #2 of Programming Options to the factory default settings - if you are not sure about current programming, change everything to the factory settings and start again. 1. Resetting all of Menu #1 to the factory setting Step1: Press buttons (I+II) simultaneouslyfor2seconds. Thiswillbe confirmedby asirenchirpandaone-timeflashingoftheparkinglight. Step2: Pressbutton III once. Thiswillbeconfirmedbyacarchirpand parkinglightflash.pressbutton III again. Youwillbeconfirmedbya carchirpandparkinglightflashagain. Pressbutton III thirdtime. Youwillbeconfirmedbyacarchirpandparkinglightflashthirdtime. Afewsecondlater,yourcarwillchirpandparkinglightflashthree timesrapidlytoconfirmtheresetting. 2. Resetting all of Menu #2 to the factory setting. Follow the same steps above except that you press buttons (I+IV) for2 seconds at the Step 1 instead of buttons (I+II).

12 21 22 Option Programming for Six Button(ONE WAY) Remotes The procedures will be same as the 4 button remotes except the use of the different buttons. Programming Programming Menu 1 Programming Menu 2 Option Selection Factory Setting Option Selection Default Setting Selection 6 Button Remote (Trunk+Start)- (Trunk+Stop)- (Stop)- Lock Unlock (Start)- 4 Button Remote (I+II)- (I+IV)- (IV) ( I ) ( II ) ( III ) Note : 1-2 Signal Light Flashing : Withthisoption,thesignalwillflashif any door remains open while the vehicle is disarmed. 1-4 Anti-Grinding (Starter-Kill) : The #1 wire of CN3 can be programmedtosendasignaltoarelaytodisconnectsthestarterwireof the vehicle upon arming and upon remote-start to prevents you from recranking the starter on a remote - started vehicle. Anti-Jacking (Ignition-Kill) : The #1 wire of CN3 can be programmed tosendasignaltoarelaytodisconnecttheignitionwireofthevehicle uponanytimethevehicleisarmedsothatthevehiclecannotstartorrun byaremoteorakey. Andtherunningofvehiclecanbeshutoffby remote s panic command. Programming Menu #2 Programming Menu #1 Option Feature Starter Delay for Diesel vehicle Signal-light flash when door remains open Duration of Door Lock Output Application of Pre-wired Kill Relay Ignition Unlock Remote Start Reservation Cranking Time (Factory Default) Button I 4sec N/A 0.8sec Anti-Grinding (Starter-Kill) ON Automatic Manual Button II 10 sec Activated 4sec Anti-jacking (Ignition-Kill) OFF Reservation is not available when any door remains open Button III For Manual only Standard Standard+ Min Standard+ Max Option Feature Turbo Hour Timer Start Remote Start Engine Running Time AUX 1 AUX 2 (Factory Default) Button I Utilization Utilization 15 Minutes 0.5 sec 0.5 sec Button II Button III Button IV N/U N/U 25 Minutes 45 Minutes 5 Minutes 20 sec 20 sec 60 sec Latch 60 sec Latch Note : 2-1, 2-2 If you want to utilize the Turbo mode and 24 Hr mode with your remote control unit, you need to program the main module at the time of installation.

13 23 Diagnosing Problems with Auto-Start Ifthereisaprobleminauto-startingyourcar,youwillhearthreechirpswhen youattempttoauto-startthecar. Waitfor2secondsandthecausefortheerrorwillbeindicatedbythenumber of timesparkinglightsflash Error Number (# of times parking lights flash) Error Reason Engine On Key On Door Open Trunk Open Reservation Off (Manual Transmission Only)