MONOBLOCK DIRECTIONAL CONTROL VALVE

Transcription

1 MONOLOCK DIRECIONL CONROL VLVE

2 Features Simple, compact and heavy duty designed monoblock valves from to 6 sections for open and closed centre hydraulic systems. H Fitted with a main pressure relief valve and a load check valve. H vailable with parallel or series circuit. H Optional carry--over port (only for parallel circuit). H Diameter mm in interchangeable spools. H wide variety of service ports and circuit valves. H vailable manual, pneumatic, hydraulic, electro--hydraulic and remote with flexible cables spool control kits. dditional information his catalogue shows the product in the most standard configurations. lease contact Sales Dpt. for more detailed information or special request. WRNING! ll specifications of this catalogue refer to the standard product at this date. Walvoil, oriented to a continuous improvement, reserves the right to discontinue, modify or revise the specifications, without notice. WLVOIL IS NO RESONSILE FOR NY DMGE CUSED Y N INCORREC USE OF HE RODUC. st edition June 6: Questa edizione aggiorna tutte le precedenti. D4E

3 Content Content Working conditions... 4 Dimensional data... 5 Hydraulic circuit... 6 erformance data... 7 Ordering codes... 8 Inlet relief options... Spools... 3 spool positioners... side options Complete controls... 4 Outlet port options Service and auxiliary valves ordering codes port relief valves anti--shock valves with cross return... 5 pilot check valves... 5 anti--shock and anti--cavitation valves Other executions SD/--N directional valve... 6 SD--S directional valve with series circuit... 6 Installation and maintenance ccessories D4E 3

4 Working conditions his catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm /s cst viscosity at 4 C temperature. Nominal flow rating 7 l/min Operating pressure (maximum) parallel circuit 35 bar 46 psi series circuit 5 bar 36 psi Max. back pressure on outlet 5 bar 36 psi Internal leakage () p= bar - 45 psi, fluid and valve at 4 C 3cm 3 /min.8 in 3 /min Fluid Mineral base oil Fluid temperature with NR seals from -- C to8 C with FM (VION) seals from -- C to C Viscosity campo di lavoro from 5 to 75 mm /s from 5 to 75 cst minima mm /s mm /s massima 4 mm /s 4 mm /s Max level of contamination 9/6 -- ISO 446 9/6 - ISO 446 mbient temperature for working conditions with mechanical control with hydraulic, pneumatic controls with electric controls NOE -- For different conditions please contact Sales Dept. from --4 C to6 C from --3 C to6 C from -- C to5 C Standard threads REFERENCE SNDRDS S UN -UNF MERIC NF HRED ISO 8/ ISO 63 ISO 6 NSI..3 CCORDING O S 779 NSI. unified CVIY ISO CCORDING O SE J96 J476a DIN shape X or Y shape X or Y ORS HRED MIN ORS S UN -UNF MERIC IInlet and carry--over C G/ 7/8--4 (SE ) M8x.5 orts and G/ 3/4--6 (SE 8) M8x.5 Outlet G3/4 7/8--4 (SE ) Mx.5 CONROL ILO ORS neumatic NF /8--7 NF /8--7 NF /8--7 Hydraulic G/4 9/6--8 (SE 6) G/4 4 D4E

5 Dimensional data (parallel circuit) E F Carry -over spool out M M spool in WLVOIL SD/- 6 4 MDE IN ILY WLVOIL SD/ MDE IN ILY Valve type roduction batch : 6 = production year (6) = progressive number Valve code YE E F Weight E F Weight YE mm in mm in kg lb mm in mm in kg lb SD/ SD/ SD/ SD/ SD/ SD/ D4E 5

6 Hydraulic circuit arallel Standard configuration with side inlet and open center circuit (E configuration). ositioner kit Load check valve llenwrench4 4 Nm / 7.7 lbft port line port line ressure line Outlet line Flow throught (LC) Main relief valve Open center plug llenwrench8 4 Nm / 7.7 lbft Lever box Standard configuration op inlet and outlet configuration 75 Description example: SD/--(JG3--)/8L/8L/E 75 Description example: SD/--(JG3--)/8L/8L/E-- S 6 D4E

7 erformance data (pressure drop vs. flow) Open center From side inlet to side outlet ressure 3 6 sections 4 sections sections Flow (l/min) Inlet to work port From side inlet to port (spool in position ) or port (spool in position ) ressure 3 6 ( 6 ) ( ) Flow (l/min) Work port to outlet From port (spool in position ) or port (spool in position ) to side outlet ressure 3 ( ) 6 ( 6 ) Flow (l/min) NOE -- Measured with spool type. D4E 7

8 Ordering codes5. Description example: st section following section SD / - (KG3 -) / 8 L / 8L. 3(G3 -) / E - SL * Main relief valve setting ort valve setting 4. I 6. Service valves page 48 ort relief valves, pilot check valves, antishock valves, anticavitation valves and combined II ody kit * YE CODE DESCRIION - 5KC43 arallel, section - 5KC43 arallel, sections 3-5KC443 arallel, 3 sections 4-5KC473 arallel, 4 sections 5-5KC53 arallel, 5 sections 6-5KC543 arallel, 6 sections Include body, seals, rings and load check valves. NOE (*) - Items are referred to S thread.. Inlet reliaf options page Standard setting is referred to l/min flow. YE CODE DESCRIION SV X5634 Valve blanking plug VMD/: direct differential pressure relief valve type K (standard) (KG -8) 5KI Range to 63 bar / 9 to 9 psi standard setting 4 bar / 58 psi (KG3 -) 5KI3 Range 63 to bar / 9 to 9 psi taratura standard bar / 75 psi (KG4 -) 5KI4 Range 8 to 35 bar / 6 to 46 psi standard setting bar / 3 psi VMD/: direct pressure relief valve type Y (YG -8) 3XCR Range 63 to 5 bar / 9 to 8 psi standard setting 8 bar / 5 psi (YG -5) 3XCR Range to 6 bar / 45 to 3 psi tandard setting 5 bar / 8 psi (YG3-75) 3XCR3 Range 5 to 5 / 8 to 36 psi standard setting 75 bar / 5 psi (YG4 -) 3XCR4 Range to 35 / 9 to 46 psi standard setting bar / 3 psi VM/: pilot pressure relief valve type X (XG -5) X6 Range 5 to 35 bar / 36 to 46 psi standard setting bar / 75 psi 8 D4E

9 Ordering codes 3. Spool options page 3 YE CODE DESCRIION 3CU43 Double acting, 3 positions, with and closed in neutral position 3CU43 Double acting, 3 positions, with open to tank in neutral position 3CU43 Double acting, 3 positions, with open to tank in neutral position 3CU453 Double acting, 3 positions, with and open to tank in neutral position 3 3CU433 Single acting on, 3 positions, plugged requires G3/8 plug (see part I ) 4 3CU4353 Single acting on, 3 positions, plugged requires G3/8 plug (see part I ) Special spools for particular positioner kits... page 6 5 3CU44 Double acting, 4 positions, floating circuit in 4 th position with spool in 5VR 3CU4436 Double acting, 4 positions, floating circuit in 4 th position with spool out, with check valve 8 3CU46 Doppio effetto, 4 pos., rigenerativo in 4 a posizione con cursore a entrare 8F 3CU46 Double acting, 4 positions, regenerative circuit in 4 th position with spool in Special spools for standard positioner kits... page 33 (9) 3CU43 Double acting, 3 positions, with and closed in neutral pos: for 9 positioner () 3CU43 Double acting, 3 positions, with and closed in neutral pos: for positioner 5. side options page 36 YE CODE DESCRIION L 5LEV Standard lever box LF 5LEV Lever box with adjustable flow limiter LS 5LEV Waterproof lever box L 5LEV3 Steel lever LE 5LEV6 Safety lever box SL 5CO Without lever box, with dust -proof plate Q 5EL CD flexible cable connection LC 5CLO Joystick lever for sections operation 7. Outlet port options page 45 YE CODE DESCRIION E 3X73 Open center plug EK 3X5345 Closed center plug E XGIU5347* G / carry -over sleeve E -EL 5CR43 With VDC electric control unloader valve; normally open circuit 5CR434 s previous 4VDC 8. Inlet and outlet selection * page 6 YE CODE DESCRIION SL 3X778 G/ plug for upper inlet (nr. request) 3X73 G3/4 plug for upper outlet (nr. request) S 3X778 G/ plug for side inlet (nr. request) 3X73 G3/4 plug for side outlet (nr. request) 9. Complete controls page 4 roportional hydraulic control type 8IM and rotative control type R. 4. side spool positioners page YE CODE DESCRIION 7FC 5V73 With friction and neutral position sensor 8 5V8 With spring return in neutral position 8D 5V8 With spring return in neutral position and pin with M6 female thread for dual control 8D 5V8 With spring return in neutral position and pin with 8mm (.3in) radial hole 8D 5V8 With spring return in neutral position and pin with M8 male thread for dual control 8L 5V83 Come tipo 8, per comando a cavo flessibile 8F 5V8 Come tipo 8 con limitatore di corsa regolabile 8M3 5V84 Come tipo 8 con perno uscente per comando microinterruttoreinposizionee 9 5V9 positions, with spring return in neutral position from position 5V9 positions, with spring return in neutral position from position 5V Detent in positions neutral, and 5V Detent in positions and 5 5V5 positions, detent in positions and neutral 6 5V6 positions, detent in positions and neutral 5V ggancio in pos. e ritorno a molla in pos. 9 5V9 With detent in position and spring return in neutral position 5V9 With detent in position and spring return in neutral position 5V Detent in positions and and spring return in neutral position 8MG3 5V85 s type 8 and microswitch in positions and 8K 5V87 s type 8 and VDC solenoid lock device 5V874 s previous, 4 VDC 8 5V87 ON/OFF pneumatic kit 8G 5V876 roportional pneumatic kit 8EG3 5V885 VDC ON/OFF electropneumatic kit 5V876 4 VDC ON/OFF electropneumatic kit 8ID3 5V88 roportional hydraulic kit 8EI3 5V835 VDC ON/OFF electrohydraulic kit 5V835 4 VDC ON/OFF electrohydraulic kit Special positioners for particular spools... page 7 9 5V95 With detent in position, automatic release in neutral position 5V5 With detent in position and, automatic release in neutral position articular positioner kits for special spools... pag V3 4 pos. with spring return in neutral pos. and detent in 4 th pos.: for spool 5 3C 5V3 4 pos. with spring return in neutral pos. and detent in 4 th pos.: for spool 5VR 8MCCR 5V8 Spring return in neutral position, with reduced spool stroke: for spool 8F 3FZ 5V36 4 pos. with spring return in neutral pos. and detent in nd pos.: for spool 8 I and ports plugs * YE CODE DESCRIION G/ 3X778 For single acting spools type 3 and 4 II Optional handlevers YE CODE DESCRIION L/Mx 7 For lever L: height mm / 7.87 in L8/Mx5 735 For joystick LC: height 5 mm / 9.84 in D4E 9

10 Inlet relief options Direct differential pressure relief vave VMD ( K G 3 - ) Standard setting in bar (for value see page 8) djustable spring type (,3,4). djustment type (G, H) djustment type G: with screw H: valve set and locked Wrenc 7-4 Nm / 3 lbft Wrench 3 4 Nm / 7.7 lbft llenwrench4 Cap code: 3CO76 max max..4.6 erformance data Spring nr. (green band) Spring nr. 3 (blue band) ressure 3 5 ressure Flow (l/min) Flow (l/min) 4 3 Spring nr. 4 (red band) 45 (% ) 5% ime response ressure 3 5 ressure 95% 9% bar 75 psi Flow (l/min) %, IME RESONSE ime ( ) D4E

11 Inlet relief options Direct pressure relief vave VMD ( Y G 3-75 ) Standard setting in bar (for value see page 8) djustable spring type (,3,4). djustment type (G, H) djustment type G: with screw H: valve set and locked Wrench 7 4 Nm / 3 lbft Wrench 3 4 Nm / 7.7 lbft Cap code: 3CO76 llenwrench4 max max erformance data Spring nr. (white band) Spring nr. (green band) Spring nr. 3 (blue band) ressure 3 5 ressure 3 5 ressure Flow (l/min) Flow (l/min) Flow (l/min) 4 3 Spring nr. 4 (red band) 45 (% ) 5% ime response resssure Flow (l/min) 3 5 ressure 95% 9% %,43 IME RESONSE 75 bar 5 psi ime ( ) D4E

12 Inlet relief options ilot pressure relief vave VM5 ( X G - ) Standard setting in bar (for value see page 8) djustment type (G, Z) 5µ m djustment type Wrench 7 4 Nm / 3 lbft G: with screw Z: with nylon tamper proof cap Wrench 4 4 Nm / 3 lbft Wrench 3 4 Nm / 7.7 lbft Cap code: 3CO8 llenwrench4 max max erformance data 4 3 Spring nr. 3 (blue band) 45 (% ) 5% ime response ressure 3 5 ressure 95% 9% bar 75 psi Flow (l/min) %,8 IME RESONSE ime ( ) SV: relief valve blanking plug llenwrench 4 Nm / 3 lbft D4E

13 Spool options ype " LC stroke: +7mm/.8 in LC closed, with flow through line (LC) open LC stroke: - 7 mm /.8 in erformance data 8 (l/min ) Spool metering () Spool metering ().. (in).. (in) 8 (l/min ) Flow 6 4 J F Y Stroke (mm) Qin = 7 l/min F (on ports) = 63bar/9psi Y (on ports) = bar/45psi J (on ports) = 5bar/36psi Flow 6 4 J F Y Stroke (mm) D4E 3

14 Spool options ype +7mm/+.8in () " () LC -- closed,, flow through line (LC) open () - 7 mm / -.8 in ype +7mm/+.8in () " () LC -- closed,, flow through line (LC) open () - 7 mm / -.8 in ype +7mm/+.8in () " () LC closed, --, with flow through line (LC) open () - 7 mm / -.8 in 4 D4E

15 Spool options ype 3 ort plugged llen wrench 8-4 Nm / 7.7 lbft +7mm/+.8in () " () LC ---- closed, with flow through line (LC) open () - 7 mm / -.8 in ype 4 ort plugged llen wrench 8-4 Nm / 7.7 lbft +7mm/+.8in () " () LC ---- closed, with flow through line (LC) open () - 7 mm / -.8 in D4E 5

16 Spool options ype 5 It needs special body with extra machining: for information please contact Sales Department. his spool must be coupled with positioner type 3 see page LC, " stroke: +5.5mm/. in 3 LC closed flow through line (LC) open 3 LC, stroke: - 5 mm /. in 3 LC -- (float in lock position) stroke: -.5 mm /.45 in erformance data 8 (l/min ) Flow Spool metering Qin=7l/min/ (on ports) = bar - 45 psi (in) ressure ressure drop in position 3 () (last section) Strole (mm) Flow (l/min) 6 D4E

17 Spool options ype 5VR It needs special body with extra machining: for information please contact Sales Department. his spool must be coupled with positioner type 3C see page LC -- (float in lock position) " " stroke: +mm/.47 in 3 LC, " stroke: +5.5mm/. in 3 LC closed flow through line (LC) open 3 LC, stroke: mm /. in erformance data 8 (l/min ) Spool metering Qin=7l/min/ (on ports) = bar - 45 psi.. (in) ressure drop in position 3 (last section) Flow 6 4 ressure Stroke (mm) Flow (l/min) D4E 7

18 Spool options ype 8F It needs special body with extra machining: for information please contact Sales Department. his spool must be coupled with positioner type 8CR see page 34. " LC stroke: +5mm/. in -- (regenerative) LC closed with flow through line (LC) open LC stroke: - 5 mm /. in, erformance data 8 (l/min ) Spool metering Qin=7l/min/ (on ports) = bar - 45 psi.. (in) ressure drop in position (in first section) Flow 6 4 ressure Stroke (mm) Flow (l/min) 8 D4E

19 Spool options ype 8 It needs special body with extra machining: for information please contact Sales Department. his spool must be coupled with positioner type 3FZ, see page " LC stroke: +6.mm/.4 in, 3 LC closed flow through line (LC) open 3 LC, stroke: mm /. in 3 LC stroke: - 9 mm /.35 in -- (regenerative) erformance data Spool metering Qin=7l/min/ (on ports) = bar - 45 psi.. (in) 8 (l/min ) ressure drop in position 3 (in first section) Flow 6 4 () ressure Stroke (mm) Flow (l/min) D4E 9

20 side spool positioners ipo 7FC with friction With sensor in neutral position llenwrench5 9.8 Nm / 7. lbft llenwrench6 4 Nm / 7.7 lbft 5. With spring return in neutral position 8kit It s supplied with standard spring type D (see force--stroke diagram) and available with lighter spring type C (8MC code:5v8) or heavier type E (8ME code: 5V84). llenwrench5 9.8 Nm / 7. lbft llenwrench6 4 Nm / 7.7 lbft (in) 4 (N) E (lbf) D 6 3 C C D E Stroke (mm) Force Force -stroke diagram 8D kit Spool end joint code XER385, is available on request in order to screw onto pin Wrench 3 4 Nm / 7.7 lbft 7.67 llenwrench5-9.8nm/7. lbft Spool end joint dimensions M8 M D4E

21 side spool positioners With spring return in neutral position 8D kit 8D kit Wrench 4 4 Nm / 7.7 lbft llenrench5-9.8nm/7. lbft Wrench 3 4 Nm / 7.7 lbft Wrench 3 4 Nm / 7.7 lbft llenrench5-9.8nm/7. lbft L kit H M ( ) Wrench 6 4 Nm / 7.7 lbft j 43 n. fori M6 prof. j.69 nr. M6 holes, depth.47 llenwrench5 9.8 Nm / 7.7 lbft 8F kit Spool stroke adjusting towards position (spool in). llenwrench5-9.8nm/7. lbft llenwrench6 4 Nm / 7.7 lbft llenwrench4 M8x Wrench3-4Nm/7.7 lbft D4E

22 side spool positioners With spring return in neutral position 8M3 kit With cams for microswitch operation. Wrench3-4Nm/7.7 lbft llen wrech Nm / 7. lbft Wrench3-4Nm/7.7 lbft llenwrench Nm / 4.9 lbft kit kit llenwrench5 9.8 Nm / 7. lbft llenwrench6 4 Nm / 7.7 lbft llenwrench5 9.8 Nm / 7. lbft llenwrench6 4 Nm / 7.7 lbft D4E

23 side spool positioners With detent Kit kit llenwrench5 9.8 Nm / 7. lbft llenwrench6 4 Nm / 7.7 lbft llenwrench5 9.8 Nm / 7. lbft llenwrench6 4 Nm / 7.7 lbft Operating features Locking and release force... : 8 N / 63 lbf ±% Operating features Locking and release force... : 8 N / 63 lbf ±% 5 kit 6 kit llenwrench5 9.8 Nm / 7. lbft llenwrench6 4 Nm / 7.7 lbft llenwrench5 9.8 Nm / 7. lbft llenwrench6 4 Nm / 7.7 lbft 5. Operating features Locking and release force... : 8 N / 63 lbf ±% 5. Operating features Locking and release force... : 8 N / 63 lbf ±% kit Special wrench Nm / 7.7 lbft llenwrench5 9.8 Nm / 7. lbft 76 Operating features Locking and release force... : N ±% D4E 3

24 side spool positioners With detent and spring return to neutral position from either directions 9 kit llenwrench5-9.8nm/7.7 lbft Special wrench 4 Nm / 7.7 lbft kit kit llenwrench5-9.8nm/7.7 lbft Special wrench 4 Nm / 7.7 lbft llenwrench5-9.8nm/7.7 lbft Special wrench 4 Nm / 7.7 lbft Force 4 (N) - Force -stroke diagram ort ort Detent area Stroke (mm) Detent force: 6 N / 58.4 lbf ±% / Release force: 5 N / lbf ±% 4 (N) Force - Force -stroke diagram ort ort 4.5 Detent area Stroke (mm) 4 (N) Force Force -stroke diagram ort ort 4.5 Detent area.. (in) Stroke (mm) osition : detent force 6 N / 58.4 lbf ±% / release force 5 N / lbf ±% osition : detent force 6 N / 58.4 lbf ±% / release force 5 N / lbf ±% (in) Detent force: 6 N / 58.4 lbf ±% / Release force: 5 N / lbf ±% (in) Detent area (lbf) (lbf) (lbf) D4E

25 side spool positioners With microswitch type 8MG3(NO) With spring return in neutral position and microswitch operated in both directions. lso available 8MG(NO) configuration (microswitch operated in position ) and 8MG(NO) configuration (microswitch operated in position ); dimensions are the same of 8MG3 configuration. Same configurations are available with normally closed (NC) contact. It s possible to obtain further control configurations, using positioners with detent type 9,, : for information contact Sales Department. Microswitch kit with connector Wrench -4Nm/3 lbft Kit 8MG3(NO) kit Wrench Nm / 7. lbft Other configurations llenn wrench 6 4 Nm / 7.7 lbft llenwrench5-9.8nm/7. lbft Kit 8MG(NO) kit Operating features MICROSWICH Mechanical life...: 5x 5 operations Electrical life (resistive load) : 5 operations - 7 / 3.5VDC :5x 4 operations - / VDC :5x 4 operations - 3 / 8VDC 8MG(NO) kit COMLEE CONROLS CODES CONROL YE Need Contact 8MG3 8MG 8MG connector type NO 5V85 5V87 5V86 C7 see NC 5V853 5V873 5V863 C7 page 65 SRE MICROSWICHES Microswitch kit with NO contact code: 4MIC73 Microswitch kit with NO contact code: 4MIC73 Microswitch kit with NC contact code: 4MIC74 87 CKRD W -CK female integrated connector with male end CKRD W -CK female connector with male end CKRD W -CK male connector with female end D4E 5

26 side spool positioners Solenoid lock device type 8K With spring return and spool electromechanical lock in neutral position; when coil is feeded the spool can be moved. It s possible to obtain further control configurations, using positioners with detent type 9,, : for information contact Sales Department. Wrench 6.6 Nm / 4.9 lbft llenwrench5 9.8 Nm / 7. lbft llenwrench6 4 Nm / 7.7 lbft Wench Nm / 7. lbft Operating features CUOR Lock stroke... : 3.5 mm /.4 in COIL Depending on model: see following features Coil with ISO44 connector Wrench Nm / 7. lbft Nominal voltage tolerance... : ±% ower rating... : 8 W Nominal current... :.58 - VDC :.8-4VDC Coil insulance... : Class F Weather protection... : I65 Duty cycle... : % Coil with Deutsch D connector COMLEE CONROLS CODES CONNECOR YE ISO44 Deutsch D ackard M -ack CONROL YE Voltage 8K 8K4 8K6 VDC 5V878 5V V VDC 5V8784 5V V87864 Need connector (page 65) C C9 C COIL CODES CONNECOR YE Voltage ISO44 Deutsch D ackard M -ack VDC X43 X434 YSOL34 4 VDC X434 X436 YSOL34 Nominal voltage tolerance... : ±% ower rating... : W Nominal current... :.9 - VDC :.95-4VDC Coil insulance... : Class H Weather protection... : I65 Duty cycle... : % Coil with ackard M -ack connector Nominal voltage tolerance... : ±% ower rating... : 8 W Nominal current... :.58 - VDC :.8-4VDC Coil insulance... : Class F Weather protection... : I65 Duty cycle... : % 6 D4E

27 side spool positioners ON/OFF pneumatic kit type 8 Wrench 3 4 Nm / 7.7 lbft Wrench 3 4 Nm / 7.7 lbft N /8 - nr. threads V 55.7 llenwrench5 9.8 Nm / 7. lbft V V 5.98 V Operating features ilot pressure...: min 5.5 bar / 8 psi max bar / 45 psi llen wrench Nm / 7. lbft roportional pneumatic kit type 8G N /8 - nr. threads Wrench 5 Wrench5-4Nm/7.7 lbft V V V V 5.98 Operating features ilot pressure...: min 6 bar / 87 psi max bar / 74 psi llenwrench4 9.8 Nm / 7. lbft Wrench 4 Nm / 7.7 lbft llenwrench5 9.8 Nm / 7. lbft 8 ilot pressure 6 4 ilot pressure - stroke diagram (with spool type ) ort ort (in) Stroke (mm) Spool overlap area Metering area D4E 7

28 side spool positioners ON/OFF electropneumatic kit type 8EG3 Symbol g9 Wrench 3.5 Nm /. lbft (+ / - %) Wrench 5 Respect the tolerance value. ightening too strongly can cause damages to the valve. V V Wrench Nm / 4.9 lbft Symbol ISO Ø6 Ø V V llenwrench4 9.8 Nm / 7. lbft Wrench 4 Nm / 7.7 lbft Wrench5-4Nm/7.7 lbft llenwrench5-9.8nm/7. lbft COMLEE CONROL CODES CONNECION YE ISO695 CONROL YE Flying leads Voltage 8EG3 8EG35 VDC 5V875 5V877 4 VDC 5V876 5V878 Need connector type (page 65) C (included) / Operating features CONROL ilot pressure... : 6 bar / 87 psi : (max. bar / 74 psi) COIL Nominal voltage tolerance... : ±% ower rating... : 8 W Nominal current... :.67 - VDC :.33-4VDC Coil insulation... : Class H Weather protection... : I65 Duty cycle... : % COILS CODES CONNECION YE Voltage ISO695 Flying leads * VDC X X 4 VDC X4 X4 * Several type of connectors can be wired on request: contact Sales Department Coil with ISO695 connector Coil with flying leads D4E

29 side spool positioner roportional hydraulic control type 8ID G/4 - nr. threads llenwrench5 9.8 Nm / 7. lbft V V V V Operating features ilot pressure... : max. 5 bar / 75 psi Wrench4-4Nm/3 lbft llenwrench4-6.6nm/4.9 lbft Wrench8-4Nm/7.7 lbft 5 ilot pressure 5 ilot pressure - stroke diagram (with spool type ) ort ort (in) Stroke (mm) Spool overlap area Metering area D4E 9

30 side spool positioners ON/OFF electrohydraulic kit type 8EI3 External pilot and drain Wrench 6.6 Nm / 4.9 lbft Symbol L V 43,5 llen wrench 3 Coil Solenoid valve: wrench Nm / 7. lbft llenwrench5 9.8 Nm / 7. lbft Symbol ISO 9 65 Collector V L llenwrench5 9.8 Nm / 7. lbft Wrench 9 Wrench3-4Nm/7.7 lbft Special wrench - 4 Nm / 7.7 lbft Operating features CONROL ilotpressure... :min.bar/45 psi : max. 5 bar / 75 psi Max backpressure on drain L... : 5 bar / 36 psi COIL Nominal voltage tolerance... : ±% ower rating... : W Nominal current... :.75 - VDC /.87-4VDC Coil insulation... : Class F Weather protection... : depending on coil model: see next page Duty cycle... : % ISO44 COMLEE CONROLS CODES CONNECION YE without diode M J CONROL YE with diode Deutsch D Voltage 8EI3 8EI3 8EI3D 8EI34 VDC 5V835 5V837 5V8374 5V VDC 5V835 5V8373 5V8375 5V8377 Need connector type (page 65) C C8 C8 C9 3 D4E

31 side spool positioners ON/OFF electrohydraulic kit type 8EI3 COIL CODES CONNECION YE M J Voltage ISO44 without diode with diode Deutsch D VDC X4 X4 X4 X44 4 VDC X44 X44 X44 X444 Coil with ISO44 connection (weather protection I65) Coil with M J connection (weather protection I65) Coil with Deutsch D connection (weather protection I67) Collector kit for external pilot and drain llenwrench6 4 Nm / 7.7 lbft V L V L bar 9 psi Collector OLLECOR KI CODES Description example: SD/--(JG3--)/8ED3L/8ED3L/E--KES -4VDC ype Code * Description KES 5KES3 For one section KES 5KES43 For sections KE3S 5KE3S43 For 3 sections KE4S 5KE4S43 For 4 sections KE5S 5KE5S43 For 5 sections KE6S 5KE6S43 For 6 sections (*) codes are referred to S thread D4E 3

32 side spool positioners ON/OFF electrohydraulic kit type 8EI3 Collector with pilot and drain he kit consists of a collector with VR pressure reducing valve and relative pipes Collector llenwrench6 4 Nm / 7.7 lbft VR valve code: S88VL Wrench 7 ilot line Wrench 9 4 Nm / 7.7 lbft Drain line Wrench 3 4 Nm / 3 lbft VR Wrench 7 4 Nm / 7.7 lbft VRC backpressure valve (not included in the kit) 75 COLLECOR KI CODES VRC Description example: SD/--(JG3--)/8EI3L/8EI3L/VRC -KER3-4VDC Operating features VR VLVE Output pressure... : bar / 9 psi Max flow... : 8 l/min Filtering... : 8 µ ype Code * Description KER3 5KER343 For one section KER3 5KER343 For sections KE3R3 5KE3R343 For 3 sections KE4R3 5KE4R343 For 4 sections KE5R3 5KE5R343 For 5 sections KE6R3 5KE6R343 For 6 sections (*) Codes are referred to S thread VRC backpressure valve: code 3XGIU5349 Valve assembled on flow through passage provides pilot pressure to the actuator Wrench 3 4 Nm / 3 lbft ressure 4 3 ressure drop Flow (l/min) 3 D4E

33 side spool positioners With detent and automatic release in neutral position 9 kit Detent in position whith automatic release when pressure towards ports exceeds setting: standard setting bar / 45 psi, range from 4 to bar / from 58 to 75 psi. his kit needs spool type (9) code 3CU43 and special body with extra machining: for information please contact Sales Department. Wrench7-4Nm/3 lbft llenwrench5 llenwrench5 9.8 Nm / 7. lbft +6.7mm/+.6in () " () Spool type (9) () mm / -.6 in llenwrench5-9.8nm/7. lbft Kit Detent in positions and with automatic release when pressure towards ports exceeds setting: standard setting bar / 45 psi, range from 4 to bar / from 58 to 75 psi. his kit needs spool type () code 3CU43 and special body with extra machining: for information please contact Sales Department. llen wrench 3 Notchmm/.79 in - 4 Nm / 7.7 lbft llenwrench5-9.8nm/7. lbft +6.7mm/+.6in () " () Spool type () () mm / -.6 in Wrench Nm / 7. lbft Wrench Nm / 7. lbft D4E 33

34 side spool positioners articular positioner kits for special spools 3 kit Detent in position 3 and spring return in neutral position; to be only couple to floating circuit spool type 5 (see page 6). llenwrench6 4 Nm / 7.7 lbft 3C kit Wrench Nm / 7. lbft llenwrench5-9.8nm/7. lbft 3 4 (N) Force Stroke (mm) Floating -.3 Force -stroke diagram ort ort (in) Detent area. Detent force: 57 N / 8 lbf ±% / Release force: 9 N / 65. lbf ±% 5.5 (lbf) Detent in position 3 and spring return in neutral position; to be only couple to floating circuit spool type 5VR (see page 7). 3 Wrench Nm / 7. lbft llenwrench5 9.8 Nm / 7. lbft 8 (N) 6 Force 4 ort Force -stroke diagram ort (in) Floating 3 (lbf) llenwrench5-9.8nm/7. lbft - Detent area Stroke (mm) - 5,5 Detent force: 6 N / 39 lbf ±% / Release force: 3 N / 67.4 lbf ±% 5,5 8CR kit With spring return to neutral position and reduced stroke ± 5mm/±.97 in. o be couple to generative circuit spool type 8F (see page 8). llenwrench5-9.8nm/7. lbft llenwrench6 4 Nm / 7.7 lbft D4E

35 side spool positioners articular positioner kits for special spools 3FZ kit Detent in position and spring return to neutral position. o be couple to generative circuit spool type 8 (see page 9). (in) Wrench 6 4 Nm / 7.7 lbft llenwrench5 9.8 Nm / 7. lbft (N) Force 3 Regenerative -.3 Force -stroke diagram ort ort Detent area Stroke (mm) Detent force: N / 45 lbf ±% / Release force: N / 49.5 lbf ±%.4 6. (lbf) 6 3 D4E 35

36 side options Lever control ype L lluminium box with protection boot lever pivot box; it can be rotated 8 (configuration L8) (*) (**) Vertical handlever assembly Horizontal handlever assembly Configuration L8 M NOE (*) - With spool type 5VR (see page 7) (**) -With spool type 5 (see page 6) llenwrench5 9.8 Nm / 7. lbft ype LF With spool stroke adjusting in position. ype LS Waterproof execution. M O -ring seal llen wrench ,5 Klinger seal llen wrench Nm / 7. lbft Wrench3-4Nm/7.7 lbft M8x llenwrench5-9.8nm/7. lbft 36 D4E

37 side options Lever control ype L Steel manufacture. ivot can be assembled below (L configuration) or above (L3 configuration). Configuration L Vertical handlever assembly Horizontal handlever assembly Configuration L3 M threads j j llenwrench5 9.8 Nm / 7. lbft D4E 37

38 side spool options Safety lever type LE Safety levers with lock in neutral complete with handlever; lift handlever knob to operate. Locking bush 5 Wrench 6 4 Nm / 7.7 lbft llenwrench5-9.8nm/7. lbft Controls prearrangement ype SL Mechanical control with dust--proof plate kit. ype SLC rotection cap usable with pneumatic 8--8G, electro--pneumatic 8EG3, hydraulic 8ID endand electro--hydraulic 8EI3 spool positioners. Dust proof seal H llenwrench8 -.8Nm/.59 lbft llenwrench5-9.8nm/7. lbft Stroke for lock release.4 ( ) 3.5 llenwrench5 9.8 Nm / 7. lbf D4E

39 side options Q cable remote control kit Waterproof cap prearranged for remote control with flexible cable. llenwrench5-9.8nm/7. lbft Wrench Nm / 7. lbft Wrench4-4Nm/7.7 lbft Flexible cable NOE - For further information about remote cable control, require related documentation. Example of cable control SCF3 remote control Q kit Cavi flessibili tipocd SD/ directional control valve without lever boxes D4E 39

40 side options LC mechanical joystick nd section spool llenwrench5-9.8nm/7. lbft Wrench 4 st section spool Wrench7-4Nm/3 lbft Wrench ivot Wrench 3 Wrench3-4Nm/7.7 lbft Wrench -4Nm/7.7 lbft llen wrench 6-4 Nm / 7.7 lbft Configuration LC4 NOE - he handlever must be ordered separately (see page 9). Dimensions and movement scheme Configuration LC pivot placed down on the left Configuration LC pivot placed down on the right st section axis nd section axis spool axis M Configuration LC3 pivot placed above on the left Cofiguration LC4 pivot placed above on the right NOE - Don t use with spool type 5DY D4E

41 7.Complete controls roportional hydraulic control type 8IM It can be used on valve with dedicated spools and body. Description example: SD / - (KG3 -) / C 8IM. 3(G3 -) / E - SL * Main relief valve setting 7. ort valve setting ody kit * Include body and load check valve. YE CODE DESCRIION - 5KC434 arallel, section - 5KC43 arallel, sections For further body kits contact Sales Department.. Inlet reliaf options For codes see page Spool options YE CODE DESCRIION C 3CU44 Double acting, 3 positions, with and closed in neutral position C 3CU454 Double acting, 3 positions, with and open to tank in neutral position NOE (*) - Items are referred to S thread. 4. Control * YE CODE DESCRIION 8IM 5IDR ilateral proportional hydraulic control with spring return 5. Service valves For types and codes see page Outlet port options * YE CODE DESCRIION E 3X73 appo per centro aperto EK 3X5345 appo per centro chiuso E XGIU5347 Giunzione carry -over G /* 7. Inlet and outlet selection * YE CODE DESCRIION SL 3X778 G/ plug for upper inlet (nr. request) 3X73 G3/4 plug for upper outlet (nr. request) S 3X778 G/ plug for side inlet (nr. request) 3X73 G3/4 plug for side outlet (nr. request) D4E 4

42 Complete controls roportional hydraulic control type 8IM Operating features Max. pilot pressure. : 5 bar / 75 psi V V G/4 V 7.83 V llenwrench6 4 Nm / 7.7 lbft ,4.4 Wrench7-4Nm/7.7 lbft llenwrench5-9.8nm/7. lbft (mm).3 (in) Stroke ilot pressure - stroke diagram / (without flow) ilot pressure.. Spools opening area C type spools metering area C type spools metering area Spools overlap area Connection example V V Hydraulic pilot control valve series SVM4 with spool control curve 88 Spool control curve type 88 with step V V 3 7 ilot pressure (in) Stroke (mm) D4E

43 Complete controls Rotative control type R It can be used on valve with dedicated spools and standard body. Description example: SD / - (KG3 -) / R SL. 3(G3 -) / E - SL * Main relief valve setting ort valve setting II. Inlet relief options For codes see page 8.. Spool options YE CODE DESCRIION R 3CU455 Double acting, 3 positions, with and closed in neutral position R 3CU4555 Double acting, 3 positions, with and open to tank in neutral position 3. side spool positioners YE CODE DESCRIION R 5RO 3 positions rotative control with neutral position sensor 4. side options YE CODE DESCRIION SL 5CO Without lever box, with dust -proof plate NOE (*) - Items are referred to S thread. 5. Service valves For types and code see page Outlet port options YE CODE DESCRIION E 3X73 Open center plug EK 3X5345 Closed center plug E XGIU5347* G / carry -over sleeve 7. Inlet and outlet selection * YE CODE DESCRIION SL 3X778 G/ plug for upper inlet (nr. request) 3X73 G3/4 plug for upper outlet (nr. request) S 3X778 G/ plug for side inlet (nr. request) 3X73 G3/4 plug for side outlet (nr. request) I CODE 3XGIU46 3XGIU499 Optional handlever with joint DESCRIION Standard model Lengthened model D4E 43

44 Complete control Rotative control type R Wrench Nm / 7. lbft llenwrench5 9.8 Nm / 7. lbft Wrench Nm / 7. lbft 3.5 llenwrench5 9.8 Nm / 7. lbft stroke Hydraulic circuit (mm / in) Description 8 / 3.9 Dimension with standard handlever 3 / 5.6 Dimension with lengthened handlever D4E

45 E: open center (standard) See page 6 SD Outlet port options It s possible to have open center, closed center and carry--over. Unloader valves are available: these valves need special bodies with appropriate cavity on lateral outlet port, the tank connection must be on top. E: with carry -over sleeve EK: closed center C G/ Wrench 3 4 Nm / 3 lbft llenwrench 4 Nm / 3 lbft C Description example: SD/--(KG3--)/8L/8L/E Description example: SD/--(KG3--)/8L/8L/EK D4E 45

46 Outlet port options Solenoid pilot unloader valves Emergency with push button and spring return; for detent position turn the button after press it: ENZIONEthe manual override option is intended for emergency use, not for continuous duty operation. Codes show at page are referred to valves with ISO44 coil, for complete valves with different electric connection contact Sales Department. Spare coils with several connectors are available, with and without diode. Directional valve body with extra--machining is requested: contact Sales Department Wrench36-4Nm/3 lbft OU ush and twist push -button for manual override Operating features VLVE Internal leakage (excited position) : max. 5 cm 3 /min at bar max..3 in 3 /min at 45 psi COIL Depending on model: see following page Hydraulic circuit 5 ressure drop 3 ressure Flow (l/min) Description example: SD/--(KG3--)/8L/8L/E--EL -VDC 46 D4E

47 Outlet port options Solenoid pilot unloader valves Voltage ISO44 COIL CODES CONNECION YE without diode M J with diode Deutsch D VDC X43 X435 X43 X434 4 VDC X434 X435 X434 X4344 Need connector (page 65) C C8 C8 C9 Coil with ISO44 connector Coil with M J connector Coil with Deutsch D connector Connector side Connector side Connector side Nom. voltage tolerance. : ±% ower rating...: 7 W Nominal current...:.58 - VDC :.8-4VDC Coil insulation...: Class F Weather protection...: I65 Duty cycle...: % Nom. voltage tolerance. : ±% ower rating...: 7 W Nominal current...:.3 - VDC :.74-4VDC Coil insulation...: Class F Weather protection...: I65 Duty cycle...: % NOE: circuit with and without bidirectional diode Nom. voltage tolerance. : ±% ower rating...: W Nominal current...:.76 - VDC :.9-4VDC Coil insulation...: Class H Weather protection...: I67 Duty cycle...: % NOE: circuit with bidirectional diode D4E 47

48 Service and auxiliary valves9. ll service and auxiliary valves need special body: contact Sales Department.. Relief valves page 49 YE CODE DESCRIION VS(G3 -) 3XCR53 Range 8 a 7 bar / 5 to 45 psi standard setting bar / 45 psi. VS S 3... antishock valves page 5 Cross return type, supplied with mounting block YE CODE DESCRIION (G3 -) 64* lock with valve on port (G3 -) 64* lock with valve on port 3(G3 -) 64* lock with valve on ports and (G -6) 5CR Single valve: range 8 to bar / 5 to75 psi, std setting 8 bar / 5 psi (G3 -) 5CR3 Single valve: range to 8 bar / 75 to 6 psi, std setting bar / 45 psi (G4 -) 5CR3 Single valve: range 6 to 35 bar / 3 to 46 psi, std setting bar / 9 psi X5643 Valve blanking plug (for configuration, ) 3. ilot check valves page 5 V VU VC V Kit V 4. Kit V V VU VC V With pre -opening, supplied with mounting block YE CODE DESCRIION S 643* lock with valve on port S 643* lock with valve on port S3 643* lock with valves on ports and S XCR66 Single valve X3336 S valves blanking plug 4. nti -schock+anti -cavitation valve page 54 hey are flange mounted on the opposite side of working ports connected in parallel with and ports, with outlet on port. YE CODE DESCRIION Kit V 5CO84 Mounting block kit 5583 Valve blanking plug VC 5KI4 nti -cavitation valve nti -shock valves V(G) 5KI Range 5 to bar / 75 to 45 psi standard setting 6 bar / 87 psi V(G3) 5KI3 Range 8 to 5 bar / 5 to 36 psi standard setting bar / 45 psi V(G4) 5KI4 Range 6 to 35 bar / 3 to 46 psi standard setting bar / 9 psi nti -shock + anti -cavitation valves VU(G) 5KI3 Range 5 to bar / 75 to 45 psi standard setting 6 bar / 87 psi VU(G3) 5KI33 ange 8 to bar / 5 to 9 psi standard setting bar / 45 psi VU(G4) 5KI34 Range 6 to 8 bar / 3 to 4 psi standard setting bar / 9 psi NOE -- Valve settings at points -4 are referred to l/min flow. NOE -- (*) Codes are referred to S threads. 48 D4E

49 Service and auxiliary valves VS relief valve it s mounted on parallel body to limitate the pressure, at lower value than main relief valve (min. gap bar / 9 psi ), on downstream section. It s in parallel with flow trough and it works only with single operation. VS ( D 3 - ) ressure setting in bar (standard bar / 45 psi) amper proof execution with blind nut C-C Wrench 4 Nm / 7.7 lbft Wrench 7 4 Nm / 7.7 lbft Wrench 4 Nm / 7.7 lbft Chiave 4 Nm / 7.7 lbft C C erformance data Spring nr. 3 (blue band) ressure 3 5 Hydraulic circuit Flow (l/min) (% ) 5% ime response ressure 95% 9% % bar 45 psi Desctription example: SD/--(KG3--)/8L/VS(D3 -)/8L/E--S,8 IME RESONSE ime ( ) D4E 49

50 Valvole secondarie anti -shock valves with cross return Cast iron block with antishock valves; for dimensions and assembling see page 5. ( D 3 - ) Standard setting in bar (for value see page 48). Spring type (,3,4). djustment with blind nut (D). mounted on port. rmounted on port. 3 mounted on ports and configuration Example of pressure on port and port to tank 3 configuration Example of pressure on port and port to tank llenwrench8 4 Nm / 3 lbft Wrench 7 4 Nm / 3 lbft llenwrench5 Wrench 4 Nm / 7.7 lbft erformance data Spring nr. (green band) Spring nr. 3 (blue band) ressure 3 5 ressure Flow (l/min) Flow (l/min) 4 3 Spring nr. 4 (red band) 45 (% ) 5% ime response ressure 3 5 ressure 95% 9% bar 75 psi Flow (l/min) %, IME RESONSE ime ( ) 5 D4E

51 Service and auxiliary valves S pilot check valves with pre -opening Cast iron block with pilot check valves; for dimensions abd assembling see page 5. S S S S3 mounted on port. mounted on port. 3 mounted on ports and. Valve type S configuration Example of pressure on port and port to tank Wrench 3 4 Nm / 3 lbft Wrench 3 4 Nm / 3 lbft Wrench 4 Nm / 7.7 lbft S3 configuration Example of pressure on port and port to tank Example of pressure on port and port to tank Example of pressure on port and port to tank erformance data ressure drop ressure Flow (l/min) ilot ratio ype With Main pre--opening S :6 :3 D4E 5

52 Service and auxiliary valves ype and S valves assembling example 3 configuration valve block S3 configuration valve block , configuration S3 configuration Standard lever box If valve block is assembled on last section, directional valve can be only supplied in SL configuration, with side inlet and outlet ports. Description example: SD/--(KG3--)/8L/8L.3(D3 -)/E--SL 5 D4E

53 Service and auxiliary valves ype and S valves assembling example Extra machining on directional valve body he same extra machining allows assembling of either valve blocks ( and S) Milled surface with fixing threaded holes C C-C M C (scale :) D4E 53

54 Service and auxiliary valves nti -shock and anti -cavitation hey need a dedicated body with extra machining: for production requirements, the blocks () are flanged on body () before the final honing of spool hole, while the valves (3) are mounted during final assembling phase. For information contact Sales Department. Valveonport Valveonport D Dimension D value (mm / in) V VU VC V 8 /.7 max. 8 /.7 max. 4 /.55 5/ D4E

55 Service and auxiliary valves V anti -shock valve V ( G 3 - ) Standard setting in bar (for value see page 43). Spring type (,3,4). djustment type (G, H). mounted on port. rmounted on port. 3 mounted on ports and. V 45 V V djustment type G: with screw H: valve set and locked erformance data Notch.5 /.59 Wrench3-4Nm/3 lbft llenwrench5-9.8nm/7. lbft Spring nr. (green band) Spring nr. 3 (blue band) ressure 3 5 ressure Flow (l/min) Flow (l/min) Spring nr. 4 (red band) ime response (% ) 5% ressure Flow (l/min) ressure 95% 9% %,5 IME RESONSE 5 bar 8 psi ime ( ) D4E 55

56 Service and auxiliary valves VU anti -shock and anti -cavitation valves VU ( G 3 - ) Standard setting in bar (for value see page 43). Spring type (,3,4). djustment type (G, H). mounted on port. rmounted on port. 3 mounted on ports and. VU 45 VU VU djustment type G: with screw H: valve set and locked erformance data Notch.5 /.59 Wrench3-4Nm/3 lbft llenwrench5-9.8nm/7. lbft Spring nr. (green band) Spring nr. 3 (blue band) Spring nr. 4 (red band) ressure 3 5 ressure 3 5 ressure Flow (l/min) Flow (l/min) Flow (l/min) ressure ressure drop Flow (l/min) 3 (% ) 5% ressure 95% 9% %.7 IME RESONSE ime response bar OVERSHOO 74 psi bar 75 psi.3 ime ( ) RNSIEN RECOVERY IME 56 D4E

57 Service and auxiliary valves VC anti -cavitation valves VC VU VU VU3 mounted on port. rmounted on port. 3 mounted on ports and. ressure drop 6 ressure Wrench3-4Nm/3 lbft llenwrench5-9.8nm/7. lbft Flow (l/min) V valve blanking plug V V V V3 mounted on port. rmounted on port. 3 mounted on ports and. llenwrench -4Nm/3 lbft llen wernch Nm / 7. lbft D4E 57

58 58 D4E

59 Other executions SD/ -N... page 6 It s available only with one working section and it can be used in hydraulic circuits where carry--over doesn t required. H For controls, spool positioning and valves, refer to directional valve with parallel circuit. SD -S: con circuito in serie... page 6 vailable from to 6 sections, it can be used in systems wich one downstream section from series connection must work with upstream ones at the same time. H Carry--over circuit is not available H On the same body are possible more than one connection. H For controls, spool positioning and valves, refer to directional valve with parallel circuit. D4E 59

60 / -N Dimensional data spool out 3 M spool in Standard threads ORS S (ISO8/) UN -UNF (ISO 96 -) MERIC (ISO 6) Inlet G / 7/8--4 UNF-- (SE ) M8x.5 orts and G/ 3/4--6 UNF-- (SE 8) M8x.5 Outlet G3/4 7/8--4 UNF-- (SE ) Mx.5 Hydraulic circuit erformance data ressure drop 5 75 Description axample: SD/--N(KG3--)/8L -- Code: 4 ressure 5 () 5 5 () Flow (l/min) 6 D4E

61 -S Dimensional data F.47 E S spool out 3 M spool in YE E F Weight E F Weight YE mm in mm in kg lb mm in mm in kg lb SD/ -S SD/5 -S SD/3 -S SD/6 -S SD/4 -S Standard threads ORS S (ISO 8/) UN -UNF (ISO 96 -) MERIC (ISO 6) Inlet G / 7/8--4 UNF-- (SE ) M8x.5 orts and G/ 3/4--6 UNF-- (SE 8) M8x.5 Outlet G3/4 7/8--4 UNF-- (SE ) Mx.5 D4E 6

62 -S Hydraulic circuit he description of SD valve with series circuit is marked with letter S and one figure wich indicate the downstream sections from series connection vailable body kits * 75 CODE DESCRIION 5KC433 SD/ -S 5KC463 SD/3 -S 5KC453 SD/3 -S 5KC53 SD/4 -S 5KC483 SD/4 -S3 5KC533 SD/5 -S 5KC563 SD/6 -S Include body, seals, rings and load check valves. Es.: SD/4--S(KG3--)/8L/8L/8L/8L Codice: 448 NOE (*) - Codes are referred to S thread. erformance data 4 erdita di carico 4 ressure drop () on 6 sections directional valve 3 6 sections ressure 4 sections sections 3 ressure 6 ( 6 ) ( ) Flow ressure drop () on 6 sections directional valve (l/min) Flow ressure drop between port () before series connection and port () after (l/min) 45 ressure ( ) 6 ( 6 ) 3 5 ressure Flow (l/min) Flow (l/min) 6 D4E

63 Installation and maintenance he SD valve is assembled and tested as per the technical specification of this catalogue. efore the final installation on your equipment, follow the below recommendations: -- the valve can be assembled in any position, in order to prevent body deformation and spool sticking mount the product on a flat surface; -- in order to prevent the possibility of water entering the lever box and spool control kit, do not use high pressure wash down directly on the valve; -- prior to painting, ensure plastic port plugs are tightly in place. C Directional valve with carry -over configuration Fittings tightening torque - Nm / lbft HREDS YE and C ports and ports port S (ISO 8/) G/ G/ G3/4 With O--Ring seal 5 / 37 5 / 37 7 / 5.6 With copper washer 6 / / / 5.6 With steel and rubber washer 6 / / / 5.6 UN--UNF (ISO 96--) 7/8--4 UNF-- (SE ) 3/4--6 UNF-- (SE 8) 7/8--4 UNF-- (SE ) With O--Ring seal 6 / / 37 6 / 44.3 MERIC (ISO 6) M8x.5 M8x.5 Mx.5 With O--Ring seal 35 / / / 37 With copper washer 4 / / / 44.3 With steel and rubber washer 4 / / / 44.3 NOE -- hese torque are recommended. ssembly tightening torque depends on many factors, including lubrication, coating and surface finish. he manufacturer shall be consulted. D4E 63

64 Installation and maintenance Sealing edge Ring chamfer Item list ) Directional valve body ) Main relief valve 3) Spool: normally the spools are inter - changeable. Verify the smoothness during the assembly 4) Lever box 5) Side spool positioner 6) Load check valve 7) Holding O -Ring bushing 8) O -Ring seal 8x,5 code: 4GU35 NOE -- ll articulated parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI Malfunction Cause Remedy External leakage pivot box lever or control kit side. Excessive internal leakage on and ports. Dropping load during transition while raising. Worn spool seal due to mechanical actuation or high back pressure. Increase clearance between spools and body due to high wear. High leakage on the load check valve Locate the leakage and replace the seal. Check back pressure level. Replace the directional control valve and check the oil contamination level. Remove the load check valve and clean the seat, verifing it s not dented. Inability to build pressure on and ressure relief valve blocked open. Remove and clean or replace the valve. ports. Low pump pressure and flow. Check the pump and circuit. 64 D4E

65 ccessories Connectors ype C code: X + according to EN ype C code: X + according to ISO44 / EN ype C7 code: 5CON male case with female end type CKRD Weather ack ype C8 code: 5CON3 female case with female end type M Junior--ower--imer ype C7 code: 5CON5 female case with male end type CKRD Weather ack ype C9 code: 5CON7 male case with female end type Deutsch D6--S ype C code: 5CON7 male case with female end type CKRD Metri--ack ype C4 code: 5CON3 male case with female end type M Superseal G9 G ype oles Nominal voltage Nominal current ermitted conductor section range ermitted cable diameter range Weather protection C + 5 VC / 3 VDC max..5 mm / max..3 in 6-8 mm / in I65 C + 5 VC / 3 VDC max..5 mm / max..3 in 6-8 mm / in I65 C7 / - mm / in mm /. -.4 in I67 C8 5 VC.5 - mm / in mm / in I65 C7 / - mm / in mm / in I67 C9 / 3 -. mm / in mm / in I67 C / mm / in mm / in I65 C4 / mm / in mm / in I67 D4E 65