Billet Fuel Filler Assemblies These billet fuel

Transcription

1 Replacement Gas Caps Fuel & Exhaust L Gas Caps OER reproduction gas caps for Camaro models. Standard gas caps come painted in a factory primer and are ready to be painted to your desired color. SS 350, SS and RS caps feature the correct semi-flat black trim with polished chrome exterior and include correct filler neck to rear body panel attachment cable. Note: The 1968 Camaro was not originally equipped with an SS-350 gas cap. However, this cap will fit on all 1968 models standard ea SS ea SS ea RS ea Bow Tie Locking Gas Cap Reproduction optional Bow Tie locking gas cap. Each cap is finished in a high quality polished chrome exterior with the correct semi flat back trim. The center includes the Chevrolet Bow Tie emblem in polished chrome. Also includes two pre-coded keys. K ea OE Style Vented Gas Cap This reproduction GM cap is meticulously reverse engineered from the OEM cap. Features correct shape, color, and markings. The quality and materials are manufactured to exact specification for the demanding restorer. Highquality representation of the original vented gas cap without EEC ea A A Camaro Billet Gas Caps These beautiful billet gas caps are CNC-machined to perfection. Available with either with a machined or polished finish. Your choice of SS, RS, or plain without logo. Plain Cap A machined finish ea A polished finish ea RS Engraved Cap A machined finish ea A polished finish ea SS Engraved Cap A machined finish ea A polished finish ea ST Replacement Gas Caps These service replacement fuel caps may differ from the original in appearance but will fit and function as original. A low cost replacement that is designed to operate correctly. Original GM Replacement Caps G w/o E.E.C ea G ea G ea G , w/fi, vin K ea G , w/fi, vin G ea G , w/fi, vin K ea G ea G ea Stant Replacement Caps Non-Locking Gas Caps ST exc Calif. models ea ST Cal. models only ea ST ea ST non vented ea ST vented ea ST non vented ea ST vented ea ST ea Locking Gas Caps ST vented ea ST exc Calif. models ea ST Calif. models only ea ST ea ST non vented ea ST vented ea ST ea ST ea Billet Fuel Filler Assemblies These billet fuel Fuel Pocket Original GM fuel pocket for all G6954 filler assemblies will add a custom look to any Camaro. Made from machined aluminum they offer OEM quality sealing and no modification installation. Assemblies include billet filler neck, custom billet locking cap with two keys, all necessary hoses, clamps and fasteners. Assemblies are available for direct fit and universal applications in both clear and black anodized finishes. An optional vent kit is also available for applications where venting is required. Note: Universal assemblies do not include hoses or clamps. Direct Fit clear anodized ea black anodized ea Universal Fit clear anodized ea black anodized ea vent kit ea Camaro models. This is a commonly damaged part due to excessive use. G ea Fuel Door Lock Protect your gas cap and fuel supply with this easyto-install key type fuel door lock. This lock can be installed on all Camaro models and can be used in addition to your factory installed remote fuel door lock! TK1029A chrome face ea TK1029B black face ea G Rear Fuel Tank Filler Doors Correct replacement bracket and hinge assembly which installs on the rear and covers the gas cap. The license plate attaches to the bracket reproduction ea B reproduction ea Fuel Door with Hinge Reproduction flush-mount fuel door for Camaro, Z28 and Berlinetta models. These exact reproductions feature the correct grain, appropriate holes to attach the rear emblem. The Berlinetta fuel door is properly finished with a chrome and black accent bar as shown standard and Z ea Berlinetta ea Fuel Doors Fuel tank filler door makes replacing the worn out or missing original easily OER repro ea G original GM ea Fuel Door Rubber Bumpers These fuel door bumpers attach directly to the rear body panel and eliminates contact between the fuel filler door and the body OER original style pr G mm, 2 required ea on fuel filler pocket ea 528 Gas Caps Toll Free Order Line

2 Replacement Fuel Tanks Now available in stainless steel R301 1 Gas Tank Tank to Filler Neck Hose Fuel Tank Upper Neck Filler Neck Sleeve Anti Squeak Kit Fuel Tank Straps Strap Mounting Bolt Kit Gas Tank Lock Ring Fuel Tank O-ring Gasket Camaro Fuel Tank Kits Replace all the necessary components for your Camaro with Classic Industries fuel tank kits. Each kit provides the individual components needed for a complete replacement. Fuel tank sending units are sold separately due to differences in engines, options, etc. Save over 10% off normal individual pricing! Note: Shipped double oversize. OS2 R zinc coating kit R stainless steel kit R zinc coating kit R stainless steel kit These reproduction fuel tanks are manufactured to factory specifications from stamped steel and are available in a variety of finishes to suit your build. Basic zinc coated steel tanks are a great value, offering strong corrosion resistance at a reasonable price. Ni-terne steel tanks provide an OE quality appearance for discerning restorers. For show quality builds, stainless steel tanks offer superior corrosion resistance with a spectacular polished finish. Zinc Coated Fuel Tanks Quality Replacement Tank Standard Corrosion Resistance Manufactured to Factory Specifications Ni-Terne Steel Fuel Tanks OE Quality Replacement Tank Exceptional Corrosion Resistance Manufactured to Factory Specifications Stainless Steel Fuel Injection Fuel Tanks Stainless steel gas tanks are a direct replacement for the OE tanks. Each tank is hand formed from 304 grade Stainless Steel and TIG welded. All tanks feature a unique baffle system. running front to rear, side to side, and around the fuel pickups to eliminate fuel starvation during acceleration and hard braking. All fittings and mounting flanges are CNC-machined from 304 Stainless steel stock to a thickness of 3/8" to ensure a proper seal. All tanks include an installed fuel pump, stainless mounting straps and hardware. All tanks have a brushed finish for easy up keep. Important: Fuel sending unit is not included with tank. Note: Shipped double oversize fuel tank ea fuel tank ea fuel tank ea Ohm fuel sending unit ea Aeromotive Fuel Tanks These tanks bring modern fuel system technology to your classic muscle car. By placing the fuel pump inside the tank, hot fuel issues such as vapor lock and cavitation are eliminated. We have all heard the stories of hot rodders being stuck on the side of the road with a fuel system or an engine that stumbles under braking, acceleration or hard cornering. These issues are related to fuel pump location, plumbing and lack of proper baffling. You can now have an in-tank fuel pump that is properly vented and submerged in fuel at all times. These new reproduction steel tanks feature a durable silver powder coat finish. In addition, they feature an internally baffled system with an in-tank performance fuel pump capable of supporting up to 1000 hp. Deep sump tanks include new fuel tank straps. Choose the bypass regulator that best serves your vehicle application. A stock capacity, 18 gallon ea A stock capacity, 18 gallon ea A " deeper than OEM, 21 1/2 gallon ea Stainless Steel Fuel Tanks Show Quality Replacement Tank Superior Corrosion Resistance Stainless Steel Polished Finish Manufactured to Factory Specifications OS Camaro Fuel Tanks A Correct reproduction fuel tanks for Camaro models. These reproduction gas tanks are manufactured to exact specifications and are available in zinc coated steel, ni-terne steel or stainless steel. Note: Shipped double oversize. OS2 Zinc Coated Steel FT1000A without fuel filler neck ea FT1001A 1969 attached fuel filler neck ea FT1002A 1970 without EEC ea FT1003A with EEC ea FT1004A all models ea FT1005A all models ea FT1006A with fuel pump on engine ea FT1007A with fuel pump in tank ea FT1008A all models ea Ni-Terne Coated Steel FT1000B without fuel filler neck ea FT1001B 1969 attached fuel filler neck ea FT1002B 1970 without EEC ea FT1003B with EEC ea FT1004B all models ea FT1005B all models ea FT1006B with fuel pump on engine ea FT1007B with fuel pump in tank ea FT1008B all models ea Stainless Steel FT1000C without fuel filler neck ea FT1001C 1969 attached fuel filler neck ea FT1002C 1970 without EEC ea FT1003C with EEC ea FT1004C all models ea FT1005C all models ea Fuel Tanks 529 Fuel & Exhaust L

3 Fuel Tank Components FT1100A FT1102A FT1104A Universal Fuel Tank Anti-Squeak Felt Universal Gas Tank Anti-Squeak inserts. These felts insert between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. Felts measure 36" long x 1-3/4" wide and are flat with no edges. Highly recommended when replacing your gas tank or mounting straps. UK915 universal fit set Fuel Neck Sleeve To Floor Clamp Reproduction of the original fuel neck sleeve clamp used to hold the sleeve to the trunk floor ea Fuel & Exhaust L FT1101B FT1103B Fuel Tank Mounting Straps Reproduction fuel tank mounting straps for models produced using heavy duty preformed steel for an original appearance or long lasting stainless steel for corrosion resistance. OE Material FT1100A pr FT1101A pr FT1102A pr FT1103A pr FT1104A pr Stainless Steel FT1100B pr FT1101B pr FT1102B pr FT1103B pr FT1104B pr Fuel Tank Strap Mounting Bolt Set It s easy to replace your fuel tank straps with fuel tank strap carriage bolts, nuts and washers. This set is recommended when replacing fuel tank straps. K piece kit set Fuel Tank Anti-Squeak Set Highest quality reproduction on the market! Includes precision die cut 1/2" sponge neoprene tank to floor cushion and 2 strap to tank inserts. Each sponge is inserted between the gas tank and the mounting straps or body. These sponges will eliminate any tank movement which may occur. Highly recommended when replacing your gas tank or mounting straps. K set C2056 C Fuel Tank Mounting Braces These correct reproduction fuel tank mounting braces are just what you need to properly and securely mount your fuel tank. Each is constructed from original gauge steel and stamped to fit as original. EDP coated for corrosion resistance. Gas tank straps will attach to these braces and securely hold the gas tank in place. EDP Coated C LH or RH (2 req.) ea C LH ea C RH ea C piece set set piece set set Weld-Thru TM Coated C2480W piece set set Fuel Tank Upper Neck Steel neck unit that runs from the gas cap down to the filler neck hose unit. Gas cap fits directly to outer portion of neck. K reproduction ea Gas Tank Filler Neck Sleeve Correct reproduction gas tank filler neck sleeve helps keep the gas tank neck from corroding as it passes through the trunk to the gas tank. The rubber sheath covers the gas tank filler neck tube which extends from the rear body tail panel to the trunk floor on its way to the gas tank. Highly recommended when replacing the gas tank neck or the gas tank assembly. Manufactured with correct molded rubber including predrilled holes for screws ea Tank To Filler Neck Hose Seals inlet filler neck to tank stub neck. This hose will eliminate gas fumes from entering in the interior or trunk area when properly installed. Each hose is produced with correct high quality neoprene and will last much longer than other hoses of inferior quality materials. K ea Fuel Sender Harness This is the correct power feed harness which activates the fuel tank float sending unit located in the gas tank. We recommend replacing this harness when installing a new gas tank sending unit to ensure an CA71184 accurate fuel gauge reading CA /2" grommet ea CA /4" grommet ea CA ea CA ea CA from 11/30/ ea CA ea Fuel Hose Pinch Clamp Reproduction style green pinch clamp for 3/8" gas hose. These clamps are found on the hose connecting the fuel tank float to the main fuel line leading to the engine. K ea Fuel Line Vapor Return Hose Line Clamp Reproduction style red pinch clamp for 1/4" gas hose. These clamps are commonly found on the fuel vapor return line connecting the fuel tank float to the fuel pump vapor return line. K ea Fuel Tank Vent Valve Reproduction plastic gas tank vent valve that mounts on the frame rail. One vapor line comes off of gas tank and goes to this valve. Originally, valve had cotton in it from the factory, this is a replacement and does not come with it. Put one cotton ball in the valve this will keep dirt from entering the gas tank ea 530 Fuel Tank Straps. Fuel Necks Toll Free Order Line

4 Fuel Tank Components Fuel Tank Sending Units Reproduction or Original GM fuel tank sending units for models. With 5/16" Fuel Lines OER Reproduction , ea V8 with 2 barrel ea cylinder ea With 3/8" Fuel Lines Note: *With 1/4" return line. OER Reproduction V8 with 4 barrel ea V ea V8 with 2 barrel ea with HP ea Z ea , 396 w/o HP ea * , ea * , ea ea * ea V ea with 1 line ea with 2 lines ea Original GM G V ea G V8 with 2 barrel ea G with HP ea G Z ea Fuel Tank Sending Unit After years of use, your fuel sending unit can corrode, its float can flood and it can simply stop working, causing your fuel gauge to read incorrectly or even not at all. This Delco Service Replacement will replace your original in both fit and function though it may differ cosmetically. Fits vehicle models with an in-tank fuel pump ea G Fuel Tank Sending Units Original GM fuel tank sending units for models. G all models ea G ea G cylinder ea FT Fuel Sender Lock Ring And Gasket Install the sending unit on your vehicle with a new reproduction sending unit lock ring and gasket set. Lock ring is manufactured from steel with zinc coating. Each set includes the lock ring and rubber o-ring gasket. Lock Ring and Gasket Sets FT set FT without EEC set FT with EEC set FT set FT fuel pump on engine set FT fuel pump in tank set FT set Lock Ring Only OER reproduction ea G GM ea OER reproduction ea G GM ea Gasket Only OER reproduction ea G GM ea OER reproduction ea G GM ea G GM ea G GM ea K404 G Fuel Tank Pickup Tube Filters Correct replacement fuel tank pickup tube strainer used to help keep contaminants in the fuel from entering into the fuel lines. This part attaches directly to the fuel tank pickup tube. OER Reproduction K /16" OEM style ea K /8" OEM style ea Original GM Replacement G /8" replacement ea G F ea G w/o fuel injection 5.99 ea G G ea G without 305 H ea G S, 5.0 F, ea G H ea G F, ea Fuel Sending Unit Float Is your fuel sending unit not reading correctly? Does your sending unit float have a crack or hole in it? Classic Industries offers a brass sending unit float that helps send accurate readings to your fuel gauge fuel sending unit float ea Fuel Tank Sender Lock Ring Tool A handy tool used to remove the fuel tank sending unit lock ring on Camaro models. CX ea A A A A A A GM Fuel Hose Stamps These stamps were used to identify hose size and placement. 1/4" hose was used for fuel return hose, 5/16" and 3/8" was used for main fuel lines. A GM 1/4 stamp ea A GM 5/16 stamp ea A GM 3/8 stamp ea This stamp was used by hose supplier SWAN on all rubber fuel hose that connected the main fuel line to the fuel sending unit and fuel pump. A SWAN GAS stamp ea This stamp was used to identify fuel hoses and was stamped about every inch. A GAS stamp ea These stamps were used to identify emissions hose size and placement. A EVAP 1/4 stamp ea A EVAP 5/16 stamp ea A EVAP 3/8 stamp ea This stamp were used to identify hose on GM vehicles with an in trunk fuel filler neck vapor system. A VAPOR ea No authentic restoration is complete without attention to every detail. These inspection stamps were placed on fuel tanks to show they had passed pressure safety testing and quality inspections. Each stamp is aesthetically accurate and includes a bottle of correct red paint. Note: Black ink was occasionally used in place of red ink. A Inspector 3 stamp ea A insp ok stamp ea Hose Marking Ink Pad This pre-inked ink pad is the correct frost white ink for marking hoses. The slow drying water based ink makes mistakes easy to correct before the ink becomes permanent. A white ink stamp pad ea Fuel & Exhaust L Fuel Tank Components 531

5 Fuel Pump Components Fuel & Exhaust L M4513 M Carter Replacement Fuel Pumps High-quality new replacement fuel pumps specifically designed for each year and engine size. Some fuel pumps may differ slightly in appearance from original but will fit and function correctly offering years of satisfactory service. Note: *Early **High Output. Mechanical and electric pump required. Inline 6 M ea M D ea M D ea V6 M K ea M A ea M ea V8 M4513 * , 5/16" outlet ea M4513 * , 5/16" outlet ea M , 3/8" outlet ea M , 3/8" outlet ea M ea M , 3/8" outlet ea M ea M ea M ea M with 4 barrel ea M H,K w/2 barrel ea M L,T w/2 barrel ea M F ea M H with Holley ea M K with Holley ea M L with Holley ea M H w/rochester ea M K w/rochester ea M L w/rochester ea M U ea M H,K,L w/4 bbl ea M Q,U ea M G,H ea M L AT with AC ea M L all without AC ea M L MT with AC ea M L AT with AC ea M J ea M J ea M H all w/o AC ea M H MT with AC ea M H AT with AC ea M L all w/o AC ea M L MT with AC ea M L AT with AC ea M H w/mech pump ea M w/mech pump ea M6626 ** G w/mech pump ea M H w/mech pump ea M6626 ** G w/mech pump ea M G ea M H without FI ea Fuel Pump Pushrod Reproduction fuel pump pushrod for all V8 engines ea G6987 G Delco Replacement Fuel Pumps Choose from a wide range of fuel pumps specifically designed for each year and engine size. Some fuel pumps may differ slightly in appearance from original but will fit and function correctly offering years of satisfactory service. Note: *Early V8 G6987 * , 5/16" outlet ea G6987 * , 5/16" outlet ea G , 3/8" outlet ea G , 3/8" outlet ea G ea G , w/3/8" outlet ea G ea G ea G ea G with 4 bbl ea G H,K with 2 bbl ea G L,T with 2 bbl ea G F ea G H with Holley ea G K with Holley ea G L with Holley ea G H w/rochester ea G K w/rochester ea G L w/rochester ea G U ea G with 2 bbl ea G H,K,L w/4 bbl ea G Q,U ea G G,H ea G L all w/o AC ea G L MT with AC ea G L AT with AC ea G J ea G J ea G H all w/o AC ea G H MT with AC ea G H AT with AC ea G L all w/o AC ea G L MT with AC ea G L AT with AC ea Holley Chrome Fuel Pumps Replace your original fuel pump with genuine Holley chrome fuel pumps. Each mechanical fuel pump is triple chrome-plated and flows 60 gallons per hour at 7-1/2 psi. Includes an adjustable lower housing allowing 360 degree rotation of fuel inlet-outlet fittings for custom installation small block ea big block ea Remanufactured Fuel Pumps These hard-to-find fuel pumps are just what your Camaro needs. Using original housings with the AC logo, factory correct markings and crimped inlet-outlet base, these are remanufactured with new components and will install and function to factory specifications , ea /325HP ea /350HP, 396/375HP ea , 327, ea /325HP (L35) ea pre-11/ ea after 11/ ea , ea /325HP, 396/350HP ea /375HP, 427/425HP ea /425HP (ZL1) ea , ea /350HP (L34) ea E1721 Performer RPM 110 GPH Fuel Pumps Designed for all Edelbrock carburetors used in Performer or Performer RPM applications. These highperformance street fuel pumps feature a high-quality three stage polished finish. The unique valve design improves flow quantity and quality, and will support engines up to 600 HP. High-volume, 3/8" NPT inlet and outlet surpasses the capacity of conventional models. Produces 6 psi and does not require a regulator. For gasoline only. Clockable lower housing can be rotated for best inlet/outlet alignment. E1721 small block ea E1722 big block ea Fuel Pump Pressure Tester Tests for fuel line pressure and vacuum leaks. Check for leaky valves, timing, fuel pump, vacuum, pressure and gas line leakage. Easy-to-read gauge with 3 foot hose and vacuum hose adapter fitting. Gauge measures vacuum from 0 to 28" HG in 1" increments. (0 to 700mm HG in 50mm increments). Measures pressure from 0 to 15 psi in 1/2 psi increments (0-1Kg/cm2 in.1 Kg/cm2 increments). Y ea 532 Fuel Pumps Toll Free Order Line

6 Fuel Pump Components Fuel Pump Bolt Sets Make sure that mechanical fuel pumps stay properly aligned by using ARP s durable black oxide finished chrome moly or rust-proof stainless bolts (both materials are rated at 170,000 psi and considerably stronger than Grade 8 hardware). Your choice of either conventional hex heads or 12 point head. Washers are included. Made in the USA. AR13162 black oxide hex head set AR13161 black oxide 12 point set AR43162 stainless hex head set AR43161 stainless 12 point set C Flames D Bow Tie E SS F RS G Fuel Pump Mounting Bolts Includes correct small head 3/8" bolts with lock washers. Fits all 8 cylinders small block pr big block pr AR43161 H Fuel Pump Bolt Sets Normal is so, well, normal. Stand apart with a set of designer hardware for your small block fuel pump. These bolts, available in either a chrome-plated or polished stainless steel finish, have traditional Chevy logos stamped directly into the head of the bolts. A great choice when the details really count! Note: Must specify logo suffi x: C Flames, D Bow Tie, E SS, F RS, G 350, H 454. Chrome 56460C small block set Stainless Steel 56460S small block set AK116A Fuel Pump Bolt Sets These are the original style hex-head bolts for all small block or big block Camaro fuel pumps. Includes a complete set for installation of one fuel pump. AK116A polished chrome set AK116B polished stainless set G6990 G Fuel Pump Mounting Plate Used to mount fuel pumps on Camaro models. Features 1 large slot and 4 mounting attachment holes. For all V8 small block engines. Includes chrome-plate to block gasket. Mounting Plate G all V8 SB ea Paper Type Gasket G SB or BB ea D Bow Tie Fuel Pump Block Off Plate Covers the hole on engine where fuel pump normally goes when using a tank mounted fuel pump. Available for big blocks and small blocks. Includes non-asbestos gasket. D small block ea D big block ea A A A Fuel Tank And Muffl er Stencils The steel sheets used to produce fuel tanks and mufflers featured manufacturer name and date code markings. These stencils make it possible to correctly mark mufflers and fuel tanks for an accurate restoration. Armco Steel A fuel tank or muffler ea A fuel tank or muffler ea A fuel tank or muffler ea A fuel tank or muffler ea A fuel tank or muffler ea Pittsburgh Steel A fuel tank or muffler ea A fuel tank or muffler ea A fuel tank or muffler ea A fuel tank or muffler ea A fuel tank or muffler ea USS Steel A fuel tank ea A fuel tank ea A fuel tank ea A fuel tank ea A fuel tank ea A fuel tank ea FPC Fuel Pump To Carburetor Lines These lines are the correct size line with original bends making installation easier. You can choose from the original style material or our upgraded stainless steel material. OEM Material FPC cyl, 5/16" ea FPC /210HP, to 4/ ea FPC /210HP, from 4/ ea FPC67ZZ bbl Z ea FPC /275HP, 5/16" ea FPC /275HP, 3/8" ea FPC /295HP, 5/16" ea FPC /295HP, 3/8" ea FPC /325HP, 3/8" ea FPC cyl, 5/16" ea FPC , bbl, 5/16" ea FPC bbl, 3/8" ea FPC /255 or 300HP set FPC / HP, 4 bbl set FPC /375HP, 4 bbl set FPC69ZZ , bbl Z set FPC69NN SB w/edelbrock carb ea FPC /300HP ea FPC BB Q-jet ea FPC BB Q-jet set FPC72ZZ Q-jet ea FPC barrel ea FPC V-8 2 barrel ea FPC Q-jet ea FPC Q-jet ea FPC barrel ea Stainless Steel FPC6701S cyl, 5/16" ea FPC6702S /210HP, to 4/ ea FPC6703S /210HP, from 4/ ea FPC67ZZS bbl Z ea FPC6705S /275HP, 5/16" ea FPC6707S /275HP, 3/8" ea FPC6705S /295HP, 5/16" ea FPC6707S /295HP, 3/8" ea FPC6709S /325HP, 3/8" ea FPC6801S cyl, 5/16" ea FPC6902S , bbl, 5/16" ea FPC6901S bbl, 3/8" ea FPC6905S /255 or 300HP set FPC6903S / HP, 4 bbl set FPC6975S /375HP, 4 bbl set FPC69ZZS , bbl Z set FPC69NNS SB w/edelbrock carb ea FPC7001S /300HP ea FPC7005S 1970 BB Q-jet ea FPC7203S BB Q-jet set FPC72ZZS Q-jet ea FPC7701S barrel ea FPC7801S 1978 V-8 2 barrel ea FPC7802S Q-jet ea FPC8001S Q-jet ea FPC8701S barrel ea FPC Pump To Carb Lines Reproduction fuel pump to carb lines and Y-block for HP models with Holley 4 barrel carbs. OEM Material FPC /8" on centers set Stainless Steel FPC6775S /8" on centers set Fuel & Exhaust L Fuel Pumps 533

7 Fuel Pump Components FPC67Y Dual Feed Holley Lines Reproduction of the dual feed fuel lines for Holley dual feed carbs. Includes 2 lines and Y-block. OEM Material FPC67Y /8" on centers ea FPC68Y /8" on centers ea Stainless Steel FPC67YS /8" on centers ea FPC68YS /8 on centers ea 1969 Fuel Filter Bracket Reproduction fuel filter bracket for all big block 1969 Camaro models with quadrajet carburetor. Produced from original material electro-plated and galvanized. K ea Fuel Line Support Bracket Reproduction fuel line support bracket for all Camaro models. C ea E Crossram Fuel Line Set Reproduction of the 5 piece fuel line set originally installed by the dealer on models equipped with the rare Crossram option. Y-block not included. E OE material set E206SS 1969 stainless steel set D65829 G Fuel Line Support Bracket This reproduction bracket was used on mid year 1969 Z28 Camaro models and 1970 Z28 (350) Camaro models. It attaches to the rear carburetor stud and loops around the fuel line. Each bracket includes the correct mounting screw. K ea T9212 Fuel & Exhaust L Single Line Fuel Hose Set Correct replacement fuel hose for all models equipped with 4 bbl. carburetors. Not for models with vapor return line. Includes correct 3/8" hose with 2 mounting clamps. K set Double Line Fuel Hose Set Correct replacement fuel hose for all models equipped with 4 barrel carburetors. For models equipped with vapor return lines. Includes correct 3/8" fuel line and 1/4" vapor return line hose with 4 mounting clamps. K set 1969 Z-28 Fuel Hose Set This set is designed to replace the fuel hoses on 1969 Z28s. Includes correct 12" forward fuel line hose (near fuel pump) and 5-1/4" rear fuel line hose (near fuel tank) with 4 clamps. K set T9245 T Replacement Fuel Filters Replace the dirty or clogged fuel filter on your classic vehicle with one of our AC Delco or aftermarket filters. We carry a variety of filters to meet your specific needs. AC Delco D for carb fuel inlet ea GM G L V8 with TBI ea G L, 5.0L 5.7L w/tbi11.99 ea G L V8 with TBI ea In-Line Fuel Filters Disposable T9177 chrome 3/8" inlet & outlet 6.99 ea T9212 chrome 5/16" inlet & outlet 4.99 ea T9245 glass 3/8" inlet & outlet 9.99 ea T9247 glass 5/16" inlet & outlet 9.99 ea In-Line Fuel Filters with Bronze Element T9407 chrome 3/8" inlet & outlet 9.99 ea Max-Clean Fuel System Cleaner Max-Clean targets and cleans deposit build up in the intake system and combustion chamber and is effective on the entire spectrum of engines on the road. Deposit build-up is a natural consequence of fuel combustion, but can have significant effects on the performance and reliability of your engine. Royal Purple s Max-Clean can restore internal engine surfaces, recovering lost fuel economy and performance. RP oz. can ea RP11723 case of 6 20 oz. cans cs 1969 Big Block Fuel Line Y-Block Excellent reproduction of the OEM style L and COPO 9560/ engine fuel line Y-block. This brass fitting mounts to the intake manifold where the two carburetor fuel inlet lines meet. Includes correct mounting bracket for correct installation. YB38B ea Big Block Fuel Line Bracket Reproduction fuel line bracket for Camaro models equipped with a big block engine. Attaches to the RH motor mount. KW RH big block ea Inline Fuel Pressure Gauge Set and monitor fuel pressure with these easy-to-use gauges! Simply splice into the existing carburetor line to with the anodized aluminum fuel block and 3/8" nipples. Each gauge measures 1-1/2" in diameter with a 0-15 psi range in 1/2 lb increments. Gauges are available in standard form or liquid filled for better vibration resistance and readability standard gauge ea liquid filled gauge ea 534 Fuel Hoses. Fuel Filters Toll Free Order Line

8 Fuel Pump Components P74006 P74050 S20192 S20194 S Electric Fuel Pumps The fit and form of a fuel pump is critical to getting the job done right. Our direct replacement electric fuel pumps feature cutting edge turbine technology, which makes them quiter, more tolerant of debris, and more efficient. They also exceed manufacturer s tolerances for the ethanol found in today s fuel blends. Buy with confidence, these fuel pumps are backed by a manufacturer s 12-month/12,000-mile warranty for defects a workmanship. Note: New strainers must be used on electric pumps for warranty compliance. Fuel pump strainers are included on electric pumps without notation. If a strainer is listed in the pump description, you must order it separately. Due to electrical requirements on certain fuel pumps, models denoted with one or two asterisks (* or **) require a strainer and wire harness adaptor for installation. *Use S20194 strainer and S88536 wire harness. **Use S20197 strainer and S88536 wire harness. Electric Pumps Inline 4 P /2.5-2 TBI without cruise control ea P /2.5-F ea P /2.5-2 except Canada ea P /2.5-2 use S20194 strainer ea P / ea V6 P74006* /2.8-S ea P74037 ** /3.1-T ea P /3.4-S ea P /3.8-K ea P74782M /3.8-K pump and sender assembly ea P74762M /3.8-K pump and sender assembly ea P74920M /3.8-K pump and sender assembly ea V8 P /5.0-7,S with electric pump ea P /5.0-G with electric pump ea P74006* /5.0-F OE replacement ea P74209HP* /5.0-F optional high-performance ea P /5.0-G high output with electric pump ea P /5.0-H without FI, use S20194 strainer ea P74006* / ea P74209HP* /5.7-8 optional high-performance ea P74006** / ea P74209HP** /5.7-8 optional high-performance ea P74000 * /5.0-E ea P74006** /5.0-F OE replacement ea P74209HP** /5.0-F optional high-performance ea P74000 ** /5.0-E ea P /5.7-P use S20197 strainer ea P /5.7-P use S20192 strainer ea P74782M /5.7-P pump and sender assembly ea P74783M /5.7-G pump and sender assembly ea P74921M /5.7-G pump and sender assembly ea Strainers and Harness New strainers must be used on electric pumps for warranty compliance. Due to electrical requirements on certain fuel pumps, models noted above with one or two asterisks (* or **) require a strainer and wire harness adaptor for installation. S20192 strainer ea S20194 strainer ea S20197 strainer ea S88536 wire harness ea Fuel Vapor Charcoal Canister Original GM or replacement fuel vapor charcoal canister used to help cut down or eliminate fuel vapor emissions. Mounts near firewall on LH side of engine compartment. 6 Cylinder G all GM ea G all GM ea VC all repro ea G all GM ea VC all repro ea 8 Cylinder G ea G ea G H CA. GM ea VC H CA. repro ea G all GM ea G all GM ea G all GM ea VC all repro ea G all GM ea VC all repro ea G4805 G6991 G Fuel Pump Relay A defective fuel pump relay can be the cause of starting problems in your Camaro. When you turn the key to the on position, you should hear the fuel pump whirr for a few moments as it pressurizes the system. If not, (and the pump is good) that may be an indication that you have a bad fuel pump relay. We now offer these original GM or reproduction fuel pump relays for models. G GM ea L (replacement) ea G GM ea S ea G ea GM ea F ea all (replacement) ea G GM ea all (replacement) ea G GM ea all 5 pin (black) ea all 4 pin (gray) ea Universal Fuel Pump Relay This universal fuel pump relay will ensure proper wiring which reduces the risk of damaging the fuel pump, and offers consistent fuel pressure. This relay is used with fuel pump part #E1791 or #E1792. E1795 universal fuel pump relay ea Fuel & Exhaust L Electric Fuel Pumps 535

9 Fuel & Exhaust L H Electric Fuel Components EFI Bypass Regulator Performance Holley Electric Fuel Pumps We offer externally mounted Holley electric fuel pumps. They all feature the proven rotor and vane design and are available in ratings from 97 gph to 140 gph. The 97 gph red pump is set at 7 psi and does not require a regulator. The 110 gph blue pump is set at 14 psi and includes a regulator. The 140 gph black pump is also set at 14 psi and can be used for gas or alcohol fuel. Red Pump H gph ea Blue Pump H gph ea Black Pump H gph ea Regulator H /2 to 9 psi ea Electric Fuel Pumps These externally mounted electric fuel pumps are ideal for most street and strip applications. Proven rotary vein technology provides high flow and stable pressures with minimal vibration and sound. Each pump features 3/8" NPT inlets and outlets along with an externally accessible pressure relief valve. Note: Not for fuel injected engines. Pumps that produce more than 7 psi should be used with a pressure regulator. Chrome Housing 100 gph 62531C 7 psi ea 120 gph 62541C 14 psi ea 140 gph 62561C 9 psi ea Cadmium Housing 100 gph psi ea 120 gph psi ea 140 gph psi ea In-Line Electric Fuel Pump This in-line electric fuel pump is continuous duty rated and is ideal for EFI applications that require additional pumping capabilities for upgraded modifications. Works superbly as either an in-line booster pump or as a stand alone unit. Use with EFI regulator part #E1728 for adjustability from 35 to 90 psi. 57 gph, 3/8" hose barb fittings. E ea Fuel Pump Safety Switch This safety feature is a must have for any electric fuel pump vehicle. This safety switch monitors the tach signal to limit when an electric pump can operate. When the key is first turned on, the fuel pump is allowed to run for three seconds, priming the fuel system. After that, it only operates if the engine is running. If the engine stops, so does the fuel pump. No plumbing into the oil lines or no extra priming button under the dash is required. RE ea E1791 Quiet-Flo Electric Fuel Pumps State-of-the-art electric fuel pumps offer maximum performance in a compact package for carbureted applications. Anodized aluminum housing and high-quality internals make it both strong and extremely durable. The E1791 electric fuel pump is factory set to 6.5 psi does not require a regulator. 3/8" inlet/outlet, 120 gph free-flow, up to 600 HP. The E1792 electric fuel pump is preset to 12 psi and requires an external regulator. 1/2" inlet-outlet, 160 gph free-flow, up to 1000 HP. Important: For proper installation and voltage requirements, use fuel pump relay E1795. E psi ea E psi ea Quiet-Flo Electric Fuel Pumps This anodized aluminum EFI fuel pump offers maximum performance in a compact package. Its rugged housing and high quality internals make it both strong and durable. The in-line design keeps the pump motor and components cool even under harsh conditions. Features -10AN inlet/outlet with a flow rate of up to 80 gph at 45 psi for high-hp fuel injected applications. This fuel pump supports 835 HP at 12 volts with a current draw of 12 amps at 45 psi. 10AN inlet/outlet 80 gph at 45 psi. Important: Dimensions: 6-7/8" x 3-1/4". E ea E1728 Fuel Pressure Regulators For those who want the best! These fuel pressure regulators are machined from aircraft quality aluminum and have fluorosilicone diaphragm material for high temperature protection and extended life. Compatible with all grades of gasoline and methanol fuels. Fully adjustable. 160 gph With 3/8" NPT Inlet/Dual Outlets E psi ea 180 gph With -6AN Inlet/Outlet/Bypass E psi ea With -10AM Dual Inlets/Outlet, -6AN Bypass E psi ea Micro Electric Fuel Pump This compact electric fuel pump is compatible with all gasoline fuels and additives. The solid state design has a low current draw of around one amp and makes a good stand alone pump or booster pump. Designed for carbureted vehicles with a 12 volt negative ground electrical system, this pump supports 4-7 psi at up to 35 gph. Includes: fittings, mounting hardware and instructions. Note: Not for diesel applications ea EFI regulator designed for medium to high horsepower applications. This regulators features Aeromotive s high-flow design, superb pressure control and legendary durability. Features base pressure adjustable from psi, gasoline and alcohol compatible, fuel pressure rises on a 1:1 ratio with boost, 1/8" National Pipe Thread taper (NPT) gauge port. Includes: two o-ring boss fittings (ORB-06) inlet ports and one o-ring boss fitting (ORB-06) return port. A adj. w/efi ea Universal Bypass Regulator A dual purpose, universal regulator for EFI or Carbureted street/ strip applications. Features pressure adjustable from 3 to 20 psi with standard spring, (installed) or from 20 to 60 psi with high pressure spring (included). Offers the full flow and rock steady fuel pressure that only a dynamic, Aeromotive bypass regulator provides. Capable of regulating any fuel pump between 100 and 250 gph, fuel pressure rises on a 1:1 ratio when referencing boost. All ports are 3/8" National Pipe Thread taper (NPT), with one inlet and three outlets on the main body and one return port on the bottom. Note: Requires a return line to be installed from the bottom of the regulator to the top of the tank. 3 Port 3/8" NPT A ea Carbureted Bypass Regulator For use when converting from fuel injection to carburetion using the EFI pump in a carbureted application. Perfect for naturally aspirated or blow-through supercharged engines. Features base fuel pressure adjustable from 3-15 psi, one o-ring boss fitting (ORB-10) inlet port and one o-ring boss fitting (ORB-08) return port, fuel pressure rises on a 1:1 ratio when referencing boost, bypass design provides the ultimate, dynamic fuel delivery system, ideal for converting from fuel injection to carburetion using the stock, in-tank pump, EFI conversions will require a larger-than-stock return line for proper low pressure control. Includes: two o-ring boss fittings (ORB-06) outlet ports and 1/8" National Pipe Thread taper (NPT) gauge port. Note: Requires Army/Navy fi tting (AN-08) return line from bottom of regulator back to top of the tank. A port ea 536 Electric Fuel Pumps Toll Free Order Line

10 Fuel Lines FGL6909 FGL7001 FGL Front-to-Rear Lines Reproduction fuel feed lines for models. Extends from the fuel tank to the fuel pump and features the correct bends. Choose between OEM material or stainless steel lines. 1 piece lines. OEM Material 6 Cylinder FGL /16" feed line ea FGL /16" feed line ea Small Block FGL /16" feed line ea FGL /8" feed line ea FGL /8" feed line ea FGL /8" feed line ea Big Block FGL /8" feed line ea FGL /8" feed line ea FGL /8" feed line ea Stainless Steel 6 Cylinder FGL6701S /16" feed line ea FGL6905S /16" feed line ea Small Block FGL6701S /16" feed line ea FGL6703S /8" feed line ea FGL6803S /8" feed line ea FGL6907S /8" feed line ea Big Block FGL6704S /8" feed line ea FGL6805S /8" feed line ea FGL6907S /8" feed line ea FGL Front-to-Rear Lines Reproduction fuel feed lines for models. Extends from the fuel tank to the fuel pump and features the correct bends. Choose between OEM material or stainless steel lines. 2 piece lines unless noted. Note: *1 piece line. OEM Material FGL /8", V6 only set FGL /8" set FGL /8", 396 only set FGL /8" set FGL7705 * /16", crossover ea FGL /8" set FGL /8", exc. Z set FGL /8", Z set Stainless Steel FGL7001S /8" set FGL7006S /8", V6 only set FGL7201S /8", 396 only set FGL7506S /8" set FGL7705S /16", crossover ea FGL7801S /8" set FGL8001S /8", exc. Z set FGL8005S /8", Z set FGL Front-to-Rear Lines Reproduction fuel feed lines for models. Extends from the fuel tank to the fuel pump and features the correct bends. Choose between OEM material or stainless steel lines. Each is guaranteed to fit perfectly. 1 piece lines. OEM Material With Carbureted Engine FGL /8", LH ea With Fuel Injected Engine FGL /8", RH ea FGL /8", filter to tank ea FGL /8", filter to hose ea FGL /8", hose to rail ea FGL /8", feed to filter ea Stainless Steel With Carbureted Engine FGL8503S /8", LH ea With Fuel Injected Engine FGL8203S /8", RH ea FGL8507S /8", filter to tank ea FGL8506S /8", filter to hose ea FGL8508S /8", hose to rail ea FGL9301S /8", feed to filter ea K0093 K Fuel Line Clip Sets Reproduction clips used to mount the steel fuel lines to the frame on various GM models. Available for single 3/8" fuel line applications and for a 3/8" line with a 1/4" return line. Note: *6 piece set. **7 piece set. Small Block K0093 * w/single 3/8" line set K0094 ** w/3/8" & 1/4" set Big Block K0093 * w/single 3/8" line set K0094 ** w/3/8" & 1/4" set Individual Clips K w/3/8" & 1/4" ea Fuel Pump Safety Switch This fuel pump safety switch shuts off fuel flow whenever oil pressure drops below 15 psi. This adds a safety factor in case of an accident or engine stall. Designed for 12 volt electrical systems and can be teed into the oil pressure sending unit with an 1/8" NPT tee ea FGL Fuel Return Lines These fuel return lines are designed to replace the original lines exactly. Includes original size line with correct bends for ease of installation. Choose from original style material or upgrade to stainless steel. All lines are 1/4" unless noted. Check below for the correct application for your year and model. Note: *5/16" tubing. Shipped double oversize. OEM Material OS2 FGL pc V ea FGL pc set FGL pc set FGL pc set FGL pc set FGL pc exc Z set FGL pc Z set FGL pc LH ea FGL8205 * pc RH ea FGL8505 * pc LH w/carb ea FGL pc RH ea FGL9302 * pc V ea Stainless Steel FGL6909S pc ea FGL7002S pc set FGL7204S pc set FGL7504S pc set FGL7802S pc set FGL8002S pc exc Z set FGL8006S pc Z set FGL8204S pc LH ea FGL8205S * pc RH ea FGL8505S * pc LH w/carb ea FGL8512S pc RH ea FGL9302S * pc V ea Fuel Vapor Lines These fuel vapor lines are designed to replace the original lines exactly. Includes original size line with correct bends for ease of installation. Choose from original style material or upgrade to stainless steel. All lines except some smaller pieces of sets are 5/16" unless noted. Check below for the correct application. Note: *1/4" tubing. Shipped double oversize. OEM Material OS2 FEM pc set FEM pc 6 cyl ea FGL7202 * pc 396 only set FEM pc set FEM pc ea FGL pc set FGL pc ea FEM pc set FEM pc set FGL pc LH ea FGL pc LH ea FGL pc RH ea FGL8504 * pc LH w/carb ea Stainless Steel FEM04S pc set FEM03S pc 6 cyl ea FGL7202S * pc 396 only set FEM74S pc set FEM05S pc ea FGL7603S pc set FGL7704S pc ea FEM08S pc set FEM10S pc set FGL8206S pc LH ea FGL8510S pc LH ea FGL8509S pc RH ea FGL8504S * pc LH w/carb ea Fuel & Exhaust L Fuel Lines 537

11 Carburetors 2523 E203 Fuel & Exhaust L Small Block 2 Barrel Carburetors These 2 barrel carburetors are excellent replacements for your Camaro. These Rochester carburetors are manufactured to original specifications and have a remote, or climatic style choke. These are replacement carburetors which include a current production date , 307, ea ea , ea 2539A ea ea ea 2538A ea ea ea ea 2574A ea ea ea , ea Federal ea California ea Federal ea California ea ea Small Block 4 Barrel Carburetors These 4 barrel Rochester carburetors are manufactured to original specifications and have a remote, or climatic style choke. These are replacement carburetors which include a current production date. Note: 4324 and 4333 must use G6999 heat shield , ea , ea ea ea ea ea ea ea ea , ea CA emission ea ea all clsd loop choke ea all ea all ea Big Block 4 Barrel Carburetors These 4 barrel Rochester carburetors are manufactured to original specifications and have a remote, or climatic style choke. These are replacement carburetors which include a current production date ea , ea 4362A , ea 4363A ea 4372A ea E208 E207 HC Cross Ram Induction Systems And Components The ultimate Camaro induction system is available as a reproduction. This system is correct in every detail and includes a GM licensed intake manifold, cast from the original tooling with correct part number and Winters Foundry markings, twin Holley carburetors with correct list and part numbers, Heim-jointed throttle linkage and throttle cable, throttle cable bracket, cable type throttle pedal arm, gaskets, all fuel lines and Y-block, oil filler tube, air cleaner elbow, complete oval or wide base style air cleaner with hood seal, heater hose fittings, throttle return spring and bracket. This is a perfect recreation of the original Cross Ram intake set up manufactured in original detail. Assembly required. Note: Cross Ram hood is available separately. See hood section for details. Complete Cross Ram Induction Sets HC with oval base air cleaner set HC with wide base air cleaner set Cross Ram Induction Components E /4" air cleaner and base assembly ea E /4" air cleaner element set CR /2" air cleaner element ea HC air cleaner seal ea E return spring bracket ea E throttle cable ea E carburetor linkage ea accelerator pedal throttle rod ea CR air cleaner elbow and nut ea TB Performance Throttle Bodies With larger ports in the throttle body your engine will receive a greater volume of air which will allow it to make more potential horsepower and less likely to be a restriction in the system. This is why we offer the 52mm and 58mm high-flow throttle bodies. Designed for outstanding throttle response and wheel spinning torque, these throttle bodies have been meticulously cast and flow bench tested for optimum airflow. It provides supreme power when mated with highflow intake systems, exhaust systems, headers, or superchargers. 50 state legal. Note: No Core Required. TB mm ea TB mm ea TB mm ea TB mm ea E204 CR101 JG1340 E202 Driven Carb Defender Driven Carb Defender fuel additive has been formulated to protect against harmful ethanol deposits and corrosion in fuel and the induction system. Special inhibitors resist expensive damage and reduced performance from moisture accumulation from modern ethanol blended gasoline. This additive controls combustion chamber residue, cleaning and protecting fuel system and intake tract surfaces to keep carburetors functioning properly. Fuel Defender is ideal for everyday drivers or classics that spend time in storage between cruises and special events. One bottle treats up to 25 gallons of ethanol blended fuel. JG oz. bottle ea JG1341 case of oz. bottles cs 538 Carburetors Toll Free Order Line

12 Edelbrock Carburetors E1806 E-Street Universal EFI System Upgrade any carbureted V8 to electronic fuel injection with this E-Street universal throttle body EFI system! Easily installs on any intake manifold with a square flange 4150 style mount and accepts virtually any cleaner. Includes: high flow four-barrel throttle body, simple-to-install wiring harness, wide band O2 sensor, computer with a pre-loaded tune, and a handheld touchscreen for easy step-by-step wireless programming. E3600 without fuel system set E1479 Edelbrock Carburetor Calibration Sets These sets include a selection of metering rods, jets, and step up springs that allow fine tuning and calibration of Edelbrock carburetors. Made in USA. Note: Not legal for pollution controlled vehicles. Performer Series Carburetor Sets E1479 for 1405 models set E1480 for 1407, 1410 models set E1480 for 1412, 1413 models set E1486 for 1403, 1404 models set E1486 for 1801, 1802 models set E1486 for 1803, 1804 models set E1487 for 1406 models set E1488 for 1409 models set E1489 for 1411 models set Thunder AVS Series Carburetor Sets E1840 for 1805 and 1806 models set E1841 for 1812 and 1813 models set E1842 for 1826 and 1826 models set Fuel Lines for Edelbrock Carburetors These fuel line and filter sets fit Thunder Series or Performer Series Carburetors. Features chromed hard steel line and Russell fuel filter. Single Feed Lines for Square Bore Carbs E8134 with blue anodized fuel filter ea E8131 with polished fuel filter ea E8126 w/3/8" barbed hose end, no filter ea Dual Feed Lines for Thunder Series AVS Carbs E8133 with blue anodized fuel filter ea E8128 with polished fuel filter ea E8132 w/3/8" barbed hose end, no filter ea Replacement Fuel Filter E8130 blue anodized fuel filter only ea E8129 polished fuel filter only ea E3604 E3607 Edelbrock High Pressure Fuel System Sets Upgrading to fuel injection requires a high pressure fuel system. Edelbrock offers a number options for converting a low pressure fuel system to high pressure for fuel injection installation. Return-Style Fuel System Includes: high pressure fuel pump, fuel filter, supply and return hose, adjustable pressure regulator with return port, fittings, mounting brackets, and hardware. Supports up to 600 HP. Important: Requires return fi tting to be installed in fuel tank. E3604 return style fuel system set Fuel Sump Module System Fuel sump modules are fed by the low pressure fuel pump and store fuel in the under the hood before providing regulated high pressure to the fuel injectors without the need of a return system. Includes: 13" x 7-3/4" x 5" sump, high pressure fuel pump and regulator pre-installed, wiring harness, fuel filters, hose, fittings, brackets and mounting hardware. Supports up to 600 HP. E psi fuel sump system set E psi fuel sump system set E1805 Edelbrock Thunder Series Carburetors Edelbrock Thunder Series carburetors share all the performance advantages of the popular Performer Series but with innovative new features. These carburetors include all of the performance features of the Performer Series carburetors and also include distinctive black hardware, dual fuel inlets (shipped with left side plugged), lightweight ball burnished and CNC profiled body, and the Quick-Tune secondary. They re available in 650 cfm and 800 cfm sizes with manual or electric choke. There s even a 650 cfm version specifically designed for off road vehicles. These Edelbrock carburetors bolt-on and run right out of the box! Simply dependable, proven performance for almost any carbureted vehicle. All Edelbrock carburetors come with an installation kit and owners manual. Note: *Off-road vehicles only. Standard Finish E cfm manual choke ea E cfm electric choke ea E1825 * 650 cfm manual choke ea E1826 * 650 cfm electric choke ea E cfm manual choke ea E cfm electric choke ea EnduraShine Finish E cfm manual choke ea E cfm electric choke ea E cfm manual choke ea E cfm electric choke ea Edelbrock Performer Series Carburetors By design, Performer Series square bore carburetors are refined to provide the widest possible torque range when matched with Edelbrock Performer, Performer RPM, RPM Air-Gap or Torker II manifold and camshaft combinations. However, these carburetors are not limited to these applications, they also match well with most stock and other manifolds of similar design. Performer Series square bore carburetors are all aluminum, ball burnished and lightweight. There are no power valves to blow out or plastic parts to break. The two piece construction resists warping and the metering rods can be changed in seconds without removing the carburetor. All Edelbrock carburetors come with an installation kit and owners manual. Note: *50 state legal for all 1980 and earlier GM V8 engines. Standard Finish E cfm manual choke ea E cfm electric choke ea E1400 * 600 cfm electric choke ea E cfm manual choke ea E cfm electric choke ea E cfm manual choke ea E cfm electric choke ea E cfm manual choke ea E cfm electric choke ea EnduraShine Finish E cfm manual choke ea E cfm electric choke ea Fuel & Exhaust L Carburetors 539

13 Performance Carburetors Fuel & Exhaust L Carburetor Main Body Features: Lightweight Aluminum Not Heavy Zinc High-Flow Center Section Design Flat Surfaces: CNC Precision Finish Changeable Screw-in Idle Air Bleeds Changeable Screw-in High Speed Bleeds High-Performance Down-Leg Boosters except 650 cfm Electric Choke on Mechanical Secondary Models Electric Choke on Vacuum Secondary Models Fuel Bowl Features: Lightweight Die-cast Aluminum Fuel Level Sight Windows Externally Adjustable Needle And Seat Dual Feed Fuel Inlet Notched Secondary Float Billet Throttle Base Plate Features: Adjustable Secondary Housing on Vacuum Secondary Models Easy Access Secondary Idle Air Flow Adjustment Strong, Lightweight Billet Aluminum Corrosion Resistant Bright Anodized Appearance Button Torx Head Throttle Plate Screws Power Valve Blow Out Protection Slip Link Linkage on Mechanical Secondary Models Billet Metering Block Features: Strong, Lightweight Billet Aluminum Four Corner Idle System on Mechanical Secondary Models Changeable Idle Feed Restrictions Durable, No Warping or Porosity Problems Secondary Jet Extensions on Mechanical Secondary Models Non-stick Gaskets PROFORM Street Series Carbs Based on the highly successful Race Series carburetors, PROFORM street carburetors are constructed with lightweight aluminum, including provisions for a choke assembly and changeable idle air bleeds for easy, non-permanent calibration changes if necessary. Fine tuning is accomplished by simply changing air bleeds, not opening up calibration restrictions with a drill bit! These dual fuel feed inlet carburetors are hand assembled in the U.S. using PROFORM High-Flow Carburetor Main Body, durable billet metering blocks, aluminum fuel bowls, and a high-performance billet throttle base plate. Mechanical Secondaries cfm electric choke ea cfm electric choke ea cfm electric choke ea cfm electric choke ea Vacuum Secondaries cfm electric choke ea cfm electric choke ea cfm electric choke ea PROFORM Race Series Carbs Finally an affordable high-performance race carburetor! PROFORM s Race Series Carburetors are hand assembled in Bowling Green, Kentucky utilizing PROFORM High-Flow Carburetor Main Body, durable billet metering blocks, aluminum fuel bowls, and a high performance billet throttle base plate. These dual fuel feed inlet carburetors are equipped with a square bore base plate. Mechanical Secondaries cfm no choke ea cfm no choke ea cfm no choke ea cfm no choke ea Vacuum Secondaries cfm no choke ea cfm no choke ea CB CB Quick Fuel Technology Hot Rod Carburetors The Hot Rod Series of carburetors is designed for street applications. Made from lightweight aluminum castings and packed full of features, these carburetors are sure to make your hot rod run its best! Hand assembled and engine tested in the USA! Available in both vacuum and mechanical secondary configurations. Note This product is not CARB exempt. Products that are not CARB exempt are legal in most states, but may not be used in California or states with similar emissions laws except on pre-1976 vehicles. Mechanical Secondary Carburetors CB cfm ea CB cfm ea CB cfm ea CB cfm ea Vacuum Secondary Carburetors CB cfm ea CB cfm ea CB cfm ea CB Quick Fuel Technology Slayer Carburetor The 600 and 750 cfm Slayer Series carburetors are designed with the same engineering innovations and featured on all QFT products. These affordable, vacuum secondary street carburetors feature all aluminum construction and handbuilt quality. They are designed with a secondary metering plate with changeable jets, eliminating the need for a costly secondary metering block. Note This product is not CARB exempt. Products that are not CARB exempt are legal in most states, but may not be used in California or states with similar emissions laws except on pre-1976 vehicles. CB cfm electric choke ea CB cfm electric choke ea CB Quick Fuel Technology Street Carburetors Super Street carburetors offer race performance in a lightweight, street friendly package. These carburetors are manufactured from aluminum and designed for maximum tunability through idle feed adjustment and power valve channel restrictions, as well as idle and high RPM air bleeds. Available with vacuum secondaries, which use fuel bowls with single sight glass windows, or a mechanical secondary design featuring dual inlet, dual sight glass 4500 style fuel bowls with links to tune the secondary opening rate. Note *Features blow-through annular booster. This product is not CARB exempt. Products that are not CARB exempt are legal in most states, but may not be used in California or states with similar emissions laws except on pre-1976 vehicles. Mechanical Secondary Carburetors CB cfm ea CB cfm annular booster ea CB * 650 cfm annular booster ea CB cfm E85 compatible ea CB cfm ea CB cfm annular booster ea CB cfm E85 compatible ea CB cfm ea CB cfm ea Vacuum Secondary Carburetors CB cfm ea CB cfm ea CB cfm ea CB cfm ea 540 Carburetors Toll Free Order Line

14 Performance Fuel Systems D1903 Street Demon Calibration Set This calibration set allows fine tuning of Street Demon carburetors. Includes: an assortment of primary jets, metering rods and step-up springs along with secondary jets all in a convenient plastic storage case. D1921 Demon calibration set set Carburetor Cover Keep dirt and contaminants out of your carburetor while working on your engine with the air cleaner removed. Produced using tough plastic construction. For all 4 barrel carburetors. 5-1/8" diameter T barrel ea D1904 Street Demon Carburetors The Street Demon redefines the street carburetor with clean looks, brisk performance, and universal design. Available in 625 and 750 cfm, the Street Demon supports stock and mildly modified V8 s with smooth, crisp throttle response. A dual bolt pattern works with most four barrel spread bore and square flange intake manifolds. Includes integrated 700R4/200R4 transmission kickdown location and electric choke. Choose from all-aluminum construction or a polymer main body design. Made in USA. 625 CFM Carburetors D1900 ball burnished finish ea D1901 with polymer main body ea D1902 hand polished finish ea 750 CFM Carburetors D1903 ball burnished finish ea D1904 with polymer main body ea D1905 hand polished finish ea Demon Universal Installation Set This set contains: installation hardware for most Demon 4 barrel carburetors, including mounting studs, washers, nuts, air cleaner studs, vacuum caps, throttle cable balls with bushing adapters for throttle levers and three types of base gaskets for square and spread bore carburetors, including a gasket for the Street Demon. D Demon installation set set Street Demon Throttle Solenoid Set Some vehicles, especially vehicles with air conditioning, require a throttle solenoid to automatically increase engine rpm. This throttle solenoid set from Demon Fuel systems includes the solenoid, bracket, and mounting nut. Made in the USA. D1950 Street Demon set 2900 MSD Atomic EFI Set The MSD Atomic EFI set fits all engines making up to 525 horsepower at the crankshaft. The annular ring charge injection design produces a better air/fuel mixture and distributes it evenly among the cylinders. As a result, engines idle, start and drive better with the Atomic EFI set. Throttle bodies feature 80 lb injectors and a self-calibrating throttle position sensor. They also feature an internal fuel rail for no-leak, no-hassle fuel delivery. The master set is complete and ready to use out of the box. It includes the EFI throttle body, electric fuel pump, fuel line and filter with hardware, power module with wide-band O2 sensor and handheld controller. Also available are the throttle body set which includes everything except for the fuel system components. Or purchase the fuel components separately. Note: Atomic EFI sets are California emissions approved for carbureted General Motors vehicles 1987 and older. E.O number D-722. Atomic EFI Master Set set Throttle Body Set set Fuel System Components for Up to 525HP set Street Demon TPS Set When using an electronic overdrive transmission, such as a 4L60E, with a carbureted engine, the transmission control unit requires a throttle position signal. This sensor bolts on to the carburetor and sends the proper signal to the computer. The simple design allows for easy calibration and voltage adjustments. Includes all necessary installation hardware. Made in USA. D1951 Street Demon TPS set set D1952 Street Demon Cable Brackets These brackets remove the guesswork when installing a Street Demon carburetor in almost any carbureted GM application. All brackets have a clear zinc coating for corrosion protection and include installation hardware. Made in USA. Throttle Rod Adapter D1952 for mechanical linkage ea Throttle and Transmission Kickdown D1953 bracket set set MSD Atomic EFI High Horsepower Fuel Set High horsepower fuel components set for MSD Atomic EFI sets. This set supports 620 horsepower at the crankshaft and supplies more fuel to the Atomic EFI throttle body than the standard Atomic EFI fuel pump. Includes: 15' of 3/8" fuel line, in-line electric fuel pump, fuel filter, brackets and EFI specific fuel line clamps set Fuel & Exhaust L Carburetors 541

15 Carburetors H90670 Holley 390 CFM Carburetor This Holley 4160 Series 390 cfm 4 barrel carburetor is ideal for small displacement V8 or V6 engines. It features side hung float bowls, a universal throttle lever, vacuum secondaries, and an electric choke. This is one of the simplest ways to get more performance from your engine. H cfm four barrel ea H4779 Holley Mechanical Secondary Carburetors These classic Holley 4150 Series double pump carburetors are available in several sizes and with manual or electric choke. These carburetors feature mechanical secondaries, center hung float bowls and power valve blow-out protection. All have manual choke. H cfm manual choke ea H cfm manual choke ea H cfm manual choke ea H cfm manual choke ea H cfm manual choke ea H cfm manual choke ea Holley Truck Avenger Series Carburetors The Holley Truck Avenger Series carburetors are designed to take the guesswork out of building a trouble free off-road/towing engine. These carburetors feature the No Trouble adjustable vacuum secondary and electric choke, externally adjustable spring loaded needle and seats, clear sight plugs. The exclusive metering block design eliminates fuel spillover through the boosters at extreme angles. When you re looking for off-road performance and reliability, choose a new Holley Truck Avenger series carburetor for your fuel delivery. H cfm four barrel ea H cfm four barrel ea H3310 Holley Vacuum Secondary Carburetors These classic Holley 4160 Series carburetors are available in several sizes and with manual or electric choke. These carburetors feature vacuum secondaries and power valve blow-out protection. All are bright chromate finish. H cfm manual choke ea H cfm electric choke ea H cfm manual choke ea H cfm electric choke ea /32" Dual-Feed Fuel Line Chrome dual-feed fuel line kits for Holley carbs. High quality gas lines specifically designed for Holley dual feed carburetors /32" inlet center to center ea /16" inlet center to center ea H80670 Holley Street Avenger Carburetors The Holley 4150 Series Street Avenger Series carburetors are the first true performance carbs specifically designed, dyno tested, and calibrated for performance on the street. They feature the No Trouble adjustable vacuum secondary, four vacuum ports, electric choke, external float adjustment, and the new Gen IV Power Valve. If you re looking for better throttle response, quicker acceleration, enhanced fuel economy and superior driveability, the Street Avenger carbs are your answer. H cfm four barrel ea H cfm four barrel ea H cfm four barrel ea HC4777A Aluminum Double Pumper Carburetors Holley s new series of aluminum double pump carburetors are constructed from aluminum, which compared to their zinc counterpart offer a 38% weight savings. Holley s aluminum double pump carburetors will hold their shine longer and also can be hand polished for a custom look. These Holley 4150 Series double pump carburetors are available in several sizes and with manual choke. These carburetors feature mechanical secondaries, center hung float bowls and power valve blow-out protection. The double pumper is designed for use on lightweight vehicles with a manual or automatic transmissions with a high stall and low rear end gears. HC4776A 600 cfm manual choke ea HC4777A 650 cfm manual choke ea HC4778A 700 cfm manual choke ea HC4779A 750 cfm manual choke ea HC4781A 850 cfm manual choke ea Fuel & Exhaust L Holley Adjustable Fuel Line Black anodized, billet aluminum adjustable fuel line for Holley carburetors. This line is manufactured with -8 AN inlet and 3/8" NPT port at the rear end. 7/8"-20 threads for the fuel bowl inlets. H and 4500 carbs ea Holley 650 CFM Carburetor This Holley 4150 Series 650 cfm 4 barrel carburetor is ideal for most moderate performance small block V8 engines. It features center hung float bowls, a universal throttle lever, vacuum secondaries, and an electric choke. This is one of the simplest ways to get more performance from your engine. H cfm electric choke ea Adjustable Dual Feed Fuel Lines Made from aircraft quality buna-n neoprene hose encased in braided stainless steel, this fuel line is temperature, gas and oil resistant. Made for 3/8" NPT fittings, the fuel line is adjustable between the carb bowls from 7-1/2" to 11-1/2". Includes 1/8" pipe fitting and plug for optional fuel pressure gauge, etc. Hose inlet nipple not included. E ea 542 Holley Carburetors Toll Free Order Line

16 Don t settle for anything less than a perfect factory original replacement! These new Holley carburetor assemblies are designed to replace the factory original exactly. Each carburetor is manufactured from the original Holley tooling ensuring an authentic and powerful replacement of the original factory installed carburetor. Carburetors Holley Carburetor Manufactured with original Holley tooling! Used on Camaro models equipped with a 302 and /375HP. This is a 780 cfm carburetor stamped with the GM # DZ and the Holley list #4053-DZ. HC ea HC /375HP ea 1970 LT1 Z28 Holley Carburetor This brand new Holley carburetor assembly for LT1 equipped 1970 Z28 Camaro models is an exact reproduction equipment, manufactured by Holley themselves, using their original tooling. Replaces GM part # on both automatic and manual transmission cars. Important: Carburetor is stamped with current manufacturing date. H auto. or man trans ea 750 CFM Holley Carburetor Classic Industries offers newly re-manufactured 750 cfm Holley carburetors. They feature an original finish, vacuum secondaries, electric choke and Power Valve blowout protection. For all engines with or without air injection reactor (smog). These replacements are similar to the 780 cfm units installed on Z28 and big block models and can be used to replace list numbers 3910, 4490, 4555, , , , and Important: Throttle solenoid used on some models not included. Order separately. Carburetor stamped with current manufacturing date. H cfm replacement carb ea 1969 Holley Carburetor Manufactured with original Holley tooling! Used on 1969 Camaro models equipped with a 396/375HP or 427/425HP. This 780 cfm carburetor is stamped with the GM # GE and the Holley list #4346-GE. HC /375HP ea HC /425HP ea 1969 Holley Carburetor Manufactured with original Holley tooling! Used on 1969 Camaro models equipped with a 427 ZL1. This is a 850 cfm double pump carburetor with mechanical secondaries and the Holley list #4296. HC /425HP ZL ea 1970 Holley Carburetor This Holley carburetor assembly for 1970 Camaro models is for LS6, L78, L89, 396, and 454 highperformance engines. Each carburetor is manufactured from the original Holley tooling insuring an authentic and powerful replacement of the original factory installed carburetor. Replaces GM part # for automatic transmission. Important: Carburetor is stamped with current manufacturing date. H auto trans ea 600 CFM Holley Carburetor Classic offers newly remanufactured 600 cfm Holley carburetors. They feature an original finish, vacuum secondaries, and Power Valve blowout protection. For all engines with or without air injection reactor (smog). These replacements are similar to the units installed on Z28 s with cross ram induction and can be used to replace list numbers 3810S, 4410A and Important: Throttle solenoid used on some models not included. Order separately. Carburetor is stamped with current manufacturing date cfm replacement carb ea Crossram Holley Carburetor Manufactured with original Holley tooling! Used on Camaro models equipped with a 302 and the crossram dealer option. This 585 cfm double pump carburetor comes with mechanical secondaries and the Holley list #4295. Fits front or rear location. 2 required. HC ea 1970 Holley Carburetor This Holley carburetor assembly for 1970 Camaro models is for LS6, L78, L89, 396, and 454 highperformance engines. Each carburetor is manufactured from the original Holley tooling insuring an authentic and powerful replacement of the original factory installed carburetor. Replaces part # for manual transmissions. Important: Carburetor is stamped with current manufacturing date. H manual trans ea Fuel & Exhaust L Holley Carburetors 543

17 Carburetor Components Holley Throttle Cable Bracket This chrome throttle cable bracket can be used with all 4150 and 4160 model square bore Holley carburetors. It includes dual stainless steel return springs. H2088 with springs ea Holley Vacuum Secondary Diaphragm This vacuum secondary diaphragm fits most 4150 and 4160 square bore Holly carburetors. H1354 diaphragm ea H45229 Manual Choke Cable Mounting Hardware This universal bracket mounts inside the vehicle under the dashboard to secure the choke control cable. The cable clamp kit is for Holley model 4010, 4150 and 4160 carburetors only. Cable Bracket H45229 universal ea Cable Clamp Kit H , 4150 and 4160 carbs set TH350 Kickdown Bracket This bracket is designed to bolt to a small block V8 intake manifold and provides a convenient mounting point for the transmission kickdown bracket. H ea Manual Choke Cable This cable can be used with all manual choke Holley carburetors. Cable length is 6 feet and the control knob has the Holley name prominently displayed. H ft length ea Holley Carburetor Ball Stud Set Install your Holley carburetor and hook it right up to your throttle linkage with these throttle ball studs. H202 set of four set Fuel & Exhaust L TH700-R4 Trans. Cable Bracket This bracket is designed to be for Holley 4150 and 4160 square bore carburetors only. It bolts onto the carburetor flange ear and provides a convenient mounting point for transmission and throttle cable. H ea Holley Fuel Inlet Nut Correct replacement fuel inlet nut for models with Holley carburetor and 5/16" fuel lines. K required ea Holley Carburetor Clear Fuel Sight Plugs These kits will enable you to eyeball the carburetors fuel level without ever having to remove another sight plug. No muss, no fuss, no mess. Sold in pairs. H6057 clear fuel sight plugs pr Transfer Tube O-ring Seals These fuel resistant o-rings will help prevent dangerous fuel leaks at your carburetors fuel transfer tube. Both old and new style o-rings are available. H2637 old style pr H10897 new style pr H34150 H10897 Holley Fuel Lines We offer chromed copper fuel lines for Holley carburetors. The hard lines are manufactured with seamless copper tubing and are double flared at the ends with 5/8"-18 inverted flare inlets. H3439 adj and 4500 carbs ea H carbs ea H carbs ea Holley Transmission Kickdown Stud Install your Holley carburetor and hook it up right with this transmission kickdown stud. H2040 transmission kickdown stud ea Float Adjustment Tool No more slight-of-hand tricks! Easily adjust your carburetor float level with this hand float adjustment tool. 5/8" socket and built-in screwdriver blade protects your engine and hands from fuel spray ea Aluminum Power Valve Remover Tool Never damage your metering blocks again! This new aluminum power valve remover tool makes power valve removal a snap. Simply place the tool over the power valve and give it an easy turn ea 544 Holley Carburetor Components Toll Free Order Line

18 Carburetor Components Holley Carburetor Float Bowl Screws These are reproductions of the screws for Holley dual float carburetor bowls. This is a set of eight 2-1/2" flat blade screws. A must when rebuilding your Holley dual float carburetor set Holley Carburetor Sets H37485 Rebuild Sets These sets are just what you need to make your Holley carburetor perform like new again. They include new gaskets, o-rings, pumps, diaphragms, needles and seats, power valves, and detailed instructions to help you step-by-step through the rebuilding process. H cfm 4160 series carbs with vacuum secondaries set H cfm 4160 series carbs with vacuum secondaries set H cfm 4160 series carbs with vacuum secondaries set H double pump carbs with mechanical secondaries set Holley Carburetor Gaskets These are reproductions of the gaskets for Holley dual float carburetors. This is a 2 piece set consisting of the base gasket as well as the air cleaner gasket. A must when rebuilding your Holley dual float carburetor pr When your Holley carburetor is due for a performance rebuild, it s time to get a Holley TricKit Set. This set contains all the parts you ll need to perform a complete rebuild on your Holley vacuum secondary or double pumper carburetor. Plus its got extra parts related to carburetor calibration that are required to accomplish a real performance tune. These include accelerator pump discharge nozzles, accelerator pump cams, vacuum secondary springs, and extra gaskets. A carburetor exploded view and detailed tuning guide are also included. This Holley TrickKit has it all! H37933 Holley Trickit Set set Holley Carburetor Gaskets H10851 We offer a selection of the most commonly needed Holley carburetor gaskets. Base Gasket and Studs H and 4160 carbs,.250" ea H and 4160 carbs, 5/16" ea Base Gasket H and 4160 carbs,.204" ea H and 4160 carbs, 5/16" ea H and 4160 carbs, 1/16" ea H and Quadrejet carbs, 1/4" ea Metering Block H , 4160 and 4165 carbs pr H , 4160 and 4165 carbs pr H , 4160 and 4165 carbs pr Fuel Bowl H and 4160 carbs pr H carbs pr H10862 Holley Carburetor Air Cleaner Gaskets This circle shaped gasket is installed between the carburetor body and the base of the air cleaner. Its a must for keeping small particles of dirt from entering your engine. They measure 5" in diameter and are available in two thicknesses " diameter.060" thick ea H " diameter.200" thick ea H2037 Holley Carburetor Throttle Studs Install your Holley carburetor and hook it up right with these throttle studs. Measurement based on diameter of throttle stud. H2037 7/32" diameter ea H2038 1/4" diameter ea Holley Carburetor Quick Change Secondary Spring Housing Make changing your vacuum secondary spring a simple job with this quick change housing. It is simple to install on any vacuum secondary Holley carburetor. H set Holley Carburetor Secondary Spring Set This set will allow you to adjust the opening of your secondaries. Includes seven color coded springs from light to heavy. H2013 set of set Fuel & Exhaust L Holley Carburetor Components 545

19 Carburetor Components Holley Jet Assortment Set The Holley jet assortment set is the professional way to track tune your Holley carburetor for top performance. The set consists of two 2 each of 36 different jet sizes ranging from #64 to #99. The jets are contained in a plastic case that keep them separated and make them easily accessible. Jet sizes selected will give the broadest range of adjustment and performance for most performance carburetor applications. H36181 jet assortment set set H12140 Holley Accelerator Pump Squirters We offer several sizes and styles of accelerator pump squirters. Choose from straight type or tube style to fit 4150, 4160 and 4500 series carburetors. All include 2 gaskets. Straight Type H straight pr H straight pr H straight pr H straight pr H straight pr H straight pr H straight pr H straight pr Tube Type H tube pr H tube pr H tube pr H tube pr H tube pr H tube pr H tube pr H tube pr Holley Power Valves H12565 The power valve is a key component of the power enrichment system of Holley performance carburetors. These power valves incorporate power valve blowout protection. Standard Flow H " Hg ea H " Hg ea H " Hg ea H " Hg ea H " Hg ea H " Hg ea H " Hg ea High Flow H " Hg ea H " Hg ea H " Hg ea H " Hg ea H " Hg ea H " Hg ea H " Hg ea H = Holley Main Jet Size #47 Desired Main Jet Size Part Number Holley Main Jets Holley jets are the professional way to track tune your Holley carburetor for top performance. They are sold in sets of two and are available in jet sizes ranging from #40 to #110. The jets will give the broadest range of adjustment to get the most performance out of your Holley carburetor. Important: Please specify jet size at the end of the part number when ordering. See chart above for more information. H122 specify jet size, #40 to # pr H2657 H4674 H209 Holley Throttle Solenoid Components Some vehicles, especially vehicles with air conditioning, require a throttle solenoid to increase engine RPM in certain conditions. The Holley bracket is designed to be used with H4674 and H2657 carburetors. The nut and solenoid are universal and can be used as replacement components for other carburetors. H4674 throttle solenoid ea H2657 solenoid nut ea H209 solenoid bracket ea T2063 Holley/AFB Carburetor Spacers Carburetor spacer sets are now available for Holley carburetors. Each set includes mounting hardware and gaskets. Open Center T2063 3/8" tall, Hiker set T2091 3/8" tall, with vacuum tube set T2094 3/8" tall, w/vacuum tube, cap set T2084 1" tall set T2103 1" tall, w/3/8" fitting for PVC set Open Center T2081 2" tall set Ported T2280 3/8" tall set T2187 1" tall, w/plug for PVC set T2048 2" tall set Fuel & Exhaust L H6506 Carburetor Needle and Seat We offer several needle and seat assemblies for Holley carburetors. The seat size determines how much fuel can flow at a certain pressure. Larger sizes flow more fuel. Tune your Holley carburetor to flow the right amount of fuel at the proper pressure with a new Viton-tipped needle and seat. H adjustable ea H adjustable ea H adjustable ea H off-road ea Holley Accelerator Pump Cam Set This set will allow you to tailor accelerator pump performance to the engine s actual requirements. Each cam has a different shape to give different results. The shape of each cam directly affects the accelerator pump stroke and pump capacity. A steeply rising cam shape will give a fast, heavy fuel shot right off idle. Conversely, a gentle sloping ramp will spread the pump action over a longer period of time. H2012 includes 8 pump cams set Billet Choke Covers These chrome-plated choke covers enhance the appearance of dressed engines by covering the plastic choke on Edelbrock, Demon, and Holley carburetors. Each billet aluminum cover comes with a snap-in louvered insert. Available as an individual cover or as a kit with polished stainless steel conduit choke cover ea choke cover kit ea 546 Holley Carburetor Components Toll Free Order Line

20 Carburetor Parts 1967 Rochester Carburetor Repair Kit You ve got the original carburetor but it needs work. What do you do? You get a carburetor repair kit and fix it! This OE style repair kit is fabulous for repairing minor problems associated with original Rochester carburetors. Each repair kit includes: gaskets, pump, needle and seat, float gauge, guide, ball, spring and retainer. Perfect for off-the-car repair. K MT with 2 barrel ea Direct Replacement Carb Main Body Replacement carburetor main body for Holley 750 cfm (#3310) vacuum secondary carburetors. This all new main body replacement will help to enhance the look and performance of your Holley carburetor without a complete replacement C ea K Choke Sets Replace your damaged or worn choke assembly with these complete sets. Reproduced with authenticity in mind. Sets include: the cover, rod, choke spring, screw, and clip on rod. Note: *With Quadrajet. K all with Holley carb set K /375HP L set K /350HP set * K0108 * /325HP or 350HP set K L78 engine set K0110 * , set ED Quadrajet Carburetor Rebuild Kits Bring your original carburetor back to original working order by replacing the crucial components with this complete rebuild kit for original or Edelbrock replacement quadrajet carburetors. Each part is manufactured to exact specifications assuring a quality part and an authentic rebuild. Includes all parts and gaskets necessary for a complete rebuild. Available for models. ED cfm kit ED cfm kit T2046 Carburetor Stud Set We offer a variety of stud kits to fit just about any Holley or Rochester carburetor. Each set includes: 4 studs, 4 nuts and 4 washers. T /8" set set T2047 2" set set T2106 3" set set Carburetor Adjusting Tool Easily adjusts GM C-4 carburetor idle mixture screws. Flexible shaft lets you reach hard to get at screws. Reversible bit fits double-d and hex head screws. X ea HC Holley Carburetor Air Cleaner Stud Correct reproduction stud used to retain the air cleaner to the carburetor. This stud is for all big block models ea HC295 universal ea Choke Rods During a multitude of years and mechanics modifications, these choke rods can become damaged or missing. Replacing this choke rod will allow your carburetor to function correctly and keep your engine running smooth. Also includes correct attachment clip /275HP w/o smog ea w/2 bbl. Rochester ea /400 2 bbl. w/o EEC ea Carburetor Tee Connector Cap For all barrel Holley carburetors barrel Holley ea Choke Thermostat Mounting Screw This mounting screw is used to hold the thermostatic choke assembly to the intake manifold ea Fuel Filter Spring Spring assembly which fits into the Rochester carburetor body and keeps tension on the fuel filter. Choose the two barrel or four barrel spring or the four barrel spring. 2 Barrel and 4 Barrel Carburetors JT ea 4 Barrel Carburetors JT ea Remote Choke Thermostat Cover Reproduction remote choke thermostat covers for Camaro models with Rochester 4 barrel carburetors with the choke thermostat mounted to the intake manifold ea K L78, 396, 402 w/qj 9.99 ea Thermostatic Choke Coil Over many years of driving, the choke coil winding can suffer undue distortion causing incorrect operation. Will install as original and will ensure countless hours trouble free driving. E Holley 4 barrel ea E Quadrajet ea ea Z28, LT ea Rochester Carburetor Heat Baffl e Carburetor heat radiation baffles for V8 full size models originally equipped with Rochester 4 barrel carburetors reproduction ea Fuel & Exhaust L Carburetor Parts 547

21 Carburetor Parts Carburetor Adapter Adapt a Holley or AFB 4 barrel carburetor to a Quadrajet 4 barrel manifold with this adapter plate. Includes all necessary hardware. E ea Carburetor Spacer Set Easily optimize the flow rates of air and fuel in your car with this modular 1" carb spacer set! Each spacer set comes with one frame and three popular inserts: open, 4 hole, and tapered 4 hole. Dial in exactly the right flow to get the most from your motor! set Heat Shield for Holley Carb OER manufactured heat shield for all GM models with Holley Carburetors. This heat shield will help cool the intake charge for better performance with 4 barrel ea EFI Fuel Return Adapter This adapter creates a return system simply by cutting a 2-3/4" section out of any standard 2" fuel filler tube. Made from aluminum with a 3/8" fitting that points 90 degrees downward to direct fuel back to the bottom of the tank. Each set includes the adapter with two buna rubber sleeves and four stainless steel clamps for a leak proof seal set TC10036 Universal Throttle Cables All Lokar throttle cables designed with a specially extruded liner for extended life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. These U-Cut-To-Fit cables are available in 36" or 48" lengths with a stainless steel inner wire. Clevis is designed without cotter pins or set screws. Includes installation instructions. Stainless 36" TC10036A ea 48" TC30048A LS1 Ramjet ea TC50048A Vortec ea Black 36" TC10036B ea Throttle Cable Bracket Reproduction throttle cable bracket for Camaro models. This quality bracket is for high-performance cars with a Holley carburetor ea Servo Bracket Correct reproduction servo mounting bracket for models with cruise control. HC ea Morse Cable Bracket Chrome-plated bracket for Holley or Quadrajet carburetor linkage plates. Can be used with part #T2333. T ea K Carb Return Springs Correct reproduction carburetor return spring found on all and 396 models. HC ea HC , ea K , ea Carb Return Spring Bracket This replacement chrome universal carb return bracket is designed to replace the original bracket for most carburetors ea Air Cleaner To Carb Gasket Manufactured for all small or big block engines with Holley or Rochester quadrajet 4 barrel carburetors /8" ea Air Cleaner Base Gasket This buna rubber air cleaner base gasket forms a positive seal between the air cleaner and the top of carburetor with a 5-1/8" neck. Designed for air cleaners with a straight lip, the gasket has a groove that fits over the lip for a superior seal against dust and debris. It can also be flipped and used on air cleaners with a rolled lip rubber ea T9756 T9757 Fuel & Exhaust L Carburetor Wedge Plate This aluminum spacer tilts forward 5 degrees to help keep it level. Measures.830" at its thickest point and has a dual bolt pattern for standard Holley, Carter AFB, and Edelbrock carburetors. Note: Not legal for pollution controlled vehicles ea Throttle Body Adapter Now you can convert from carburetion to TBI without having to replace your manifold. This adapter bolts on any square or spread bore manifold and accepts any 43mm bore throttle body from 4.3L, 5.0L and 5.7L GM engines ea Carburetor Linkage Plate Each plate is triple chrome-plated for a beautiful and custom finish. For GM cables. T2333 Holley/AFB ea Throttle Cable Bracket Kit Chrome-plated bracket set small block Chevy with cable type linkage. May be used with either round or square mounts. You do not have to remove the carburetor to install. Allows full adjustment. Note: Use T9757 also if you have a TH350 transmission. Throttle Cable Bracket T9756 small block set Kickdown Bracket T trans ea 548 Carburetor Parts Toll Free Order Line

22 Fuel System Parts Throttle Cable Kickdown Bracket Chrome throttle cable transmission kickdown bracket for vehicles with a TH350 transmission. T ea Universal Accelerator Throttle Rod This rod is for use when modifications will not allow the use of the original rod between the accelerator pedal lever and the carburetor. Bend and shape as needed. 14-1/2" long. Note: Not for cable operated applications. AL ea Carb & Throttle Arm Linkage Bushing Reproduction grommet and sleeve unit where the accelerator rod fits into linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will keep your throttle rod from becoming loose or sloppy. Includes cotter pin. K bushing/sleeve set T9619 Carburetor Mount Linkage Bracket These brightly polished, chrome-plated brackets can be installed on vehicles equipped with Holley carburetors. For GM cables. T9619 manual transmission ea T9620 automatic transmission ea Carburetor Rod Clip Reproduction carburetor rod to accelerator rod clip for Camaro models ea BK5004 BK BBK LS1 & LS6 Intake Manifolds Boost horsepower and low end torque with this intake manifold from BBK. Designed for LS1 and LS6 engines, this intake improves the Z06 Corvette intake design with an 85mm straight through throttle inlet with rounded low restriction intake runners to allow an horsepower increase on a base LS1 engine. Features a titanium powder coat finish and is available in sets with BBK Power Plus series 80mm throttle bodies with cable or electronic throttle controls. Uses factory rubber o-ring gaskets and includes mounting hardware and instructions. Check state law before ordering. BK manifold only ea BK with cable TB set BK with electronic TB set BBK LS1 & LS6 Throttle Body BBK LS1 and LS6 throttle bodies are designed to increase airflow on models to add between 7-12 horsepower. These throttle bodies are CNCmachined from quality castings and feature OEM die-stamped linkages, double sealed bearings, o-ringed throttle shafts and include new gaskets with detailed instructions with all parts and necessary hardware for installation. 50 state legal. BK mm ea BK mm ea A970136A A970137A A970138B A970139C Custom Throttle Body Plates Custom throttle body plates for Camaro models equipped with a LT1 or TPI engine. Made from billet aluminum and anodized in your choice of black, red, or blue. Includes stainless screws for installation. Designed to fit any TPI or LT1 engine. Note: Please specify color when ordering. IROC-Z Logo A970136A black ea A970136B red ea A970136C blue ea Z28 Logo A970137A black ea A970137B red ea A970137C blue ea Bowtie Logo A970138A black ea A970138B red ea A970138C blue ea SS Logo A970139A black ea A970139B red ea A970139C blue ea T2386 Throttle Spring Return Sets Mounts to intake manifold on driver side. Required by many race sanctioning bodies and a great idea for any high-performance car, these intake manifold mounted throttle return spring and bracket sets provide positive throttle return. Includes: chrome brackets, springs, bushings, and fastener. DC2083 Holley 2300, barrel set DC2083 Holley 4150, barrel set T2386 big block set T2387 SB (tall for use w/carb spacers) set TF Billet TPI Throttle Cable Brackets These billet aluminum cable brackets from Lokar mount to the side of your TPI intake plenum and allow you to install your throttle cables. Brackets are available with a single hole stud for throttle only, a dual hole stud for throttle and kickdown, and a triple hole stud for a throttle, kickdown and cruise control cables. Your choice of brushed or polished finish. Made in USA. Brushed Aluminum TF single hole stud ea TF double hole stud ea TF triple hole stud ea Polished Aluminum TF single hole stud ea TF double hole stud ea TF triple hole stud ea Perfect Flow Fuel Delivery System The Perfect Flow Fuel Delivery System is a fuel pump system designed to support up to 1000 horsepower in naturally-aspirated engines. It can also be configured as a main and secondary pump to support up to 500 horse power in situations where a redundant fuel delivery system is needed. Set includes wiring and relays. Fittings are not included with this set set Fuel & Exhaust L Carburetor Parts 549

23 Exhaust Manifolds 1968 Small Block Exhaust Manifolds There s no better feeling than knowing you re replacing an integral part of your engine with correct reproductions! Each reproduction exhaust manifold is specifically designed to replace the original exactly, including correct part numbers cast into each manifold. This reproduction is regarded as the early style and does not include smog tube holes. Sold in pairs only for a complete replacement. E small block pr EMBB16P LS Cast Iron Exhaust Manifolds These Hooker cast iron exhaust manifolds are designed to hug the engine block closely so they will work with a variety of LS engine swaps or as a replacement. Their contoured shape aims exhaust gases for increased flow and performance over stock manifolds with a traditional old school look. Fits all GM LS engines up to 500 horsepower except LS7 and LS9 s and have been proven to fit F-Bodies, G-Bodies, and A-Body vehicles. Made from high silicon ductile iron for years of durability and corrosion resistance. Available in a range of different finishes. Important: Not C.A.R.B. certifi ed and may not be legal for use in some states on pollution controlled vehicles As Cast finish pr black ceramic finish pr silver ceramic finish pr titanium ceramic finish pr cast iron gray ceramic finish pr E316 EMBB17P Big Block Exhaust Manifolds Reproduction exhaust manifolds for big block models. These extremely high-quality manifolds are designed and manufactured to exact original specifications including the correct casting numbers for models. The manifolds are also correct for big blocks with the exception of the casting numbers, which were different. Reproduction manifolds were outflow tested to ensure factory equivalent specifications. Manifolds are sold in pairs only. Without Air Injection Tube Holes EMBB16P big block pr With Air Injection Tube Holes EMBB17P big block pr A Ram's Horn Exhaust Manifolds These exhaust manifolds are based on the famous high-performance small block Chevy Ram s Horn manifolds from the 1950 s and 60 s. Manufactured from heavy cast iron without air injection ports or alternator/generator bracket provisions. Available in raw cast iron, black ceramic, silver ceramic or with a heavy chrome finish. Includes mounting hardware and gaskets. Sold in pairs. Note: Not legal for use on pollution controlled vehicles. A raw cast manifolds pr A chrome manifolds pr A black ceramic manifolds pr A silver ceramic manifolds pr Before After Fuel & Exhaust L EMSB15P Small Block Exhaust Manifolds There s no better feeling than knowing you re replacing an integral part of your engine with correct reproductions! Each reproduction exhaust manifold is specifically designed to replace the original exactly, including correct part numbers cast into each manifold. This reproduction is regarded as the early style and does not include smog tube holes. Used on small block engines. Sold in pairs only for a complete replacement. Available with or without holes for Air Injection tubes. Note: *For automatic transmission only. E316* w/o Air Injec pr EMSB15P w/air Injec pr Cast Iron Manifold Dressing Apply this non-toxic manifold dressing to your manifolds with a cloth and polish them to a silvery shine. One 3 ounce container will do approximately 3 sets of manifolds. Burn proof up to 1800 degrees F. CY ounce can ea Fenton Small Block Headers Classic Fenton cast iron small block headers split dual exhaust systems into a unique, high-flow quad exhaust system. Universal fit for , 327 and 350 cid engines. AJ5314 Fenton SB headers pr 550 Exhaust Manifolds Toll Free Order Line

24 Exhaust Manifold Parts Exhaust Flange E246 Correct replacement exhaust flange for big block or small block applications to secure the headpipe to the exhaust manifold. E small block ea E big block ea Headpipe Tube Extension These is the short extension pipe which slips in between the exhaust manifold and the main header pipe and supports the exhaust pipe packing gasket. This item is manufactured in original material. Small Block " o.d ea Big Block /4" o.d ea Upper Heat Stove Exhaust manifold upper heat stove which is used with the air heat tube to preheat the air cleaner thermosensor. This item mounts on the RH (passenger side) exhaust manifold. The air tube is inserted into this item. For V8 models only with TH ea with PG ea , ea without ea without 402, ea without ea , 350, ea SB Exhaust Manifold Heat Riser Heat riser valves are located between the exhaust manifold and the head pipe and are used to hasten the warm up of a cold engine. A malfunctioning or frozen valve can cause loss of power or exhaust manifold damage. Fits Chevrolet small block models with 2" headpipe. Note: Images are shown from the bottom (pipe) side small block ea Exhaust Pipe Packing Gasket Original GM pipe packing gasket. This unit installs between the headpipe and exhaust manifold outlet. Heat resistant gasket which helps prevent exhaust leaks. Measures: 2-1/32" i.d. x 2-1/2" o.d. G ea Lower Heat Stove This lower heat stove was originally installed on models. For V8 small block engines as listed with TH ea with PG ea , ea without 402, ea without ea U, 350L ea U, 305G, 350L ea , 350H, 350L ea BB Exhaust Manifold Heat Riser Heat riser valves are located between the exhaust manifold and the head pipe and are used to hasten the warm-up of a cold engine. Malfunctioning or frozen valves can cause loss of power or exhaust manifold damage. G big block ea Exhaust Manifold Heat Riser Heat riser valves are located between the exhaust manifold and the head pipe and are used to hasten the warm-up of a cold engine. Malfunctioning or frozen valves can cause loss of power or exhaust manifold damage. E ea Exhaust Pipe Packing Gasket This heat resistant gasket installs between the headpipe and exhaust manifold outlet. Measures: 2" i.d. x 2-1/2" o.d gasket ea Engine To Exhaust Crossover Pipe Ring Replacement ring used to link the exhaust manifold to the front exhaust crossover pipe. This ring is necessary when replacing the front exhaust pipes. Measures: 2" i.d. x 2-1/2" o.d ea Oxygen Sensor Fitting Weld-in oxygen sensor fitting for all fuel injection systems ea Air Heat Stove Mounting Stud This is the factory stud used to mount the air heat stove to the exhaust manifold. Fits , , 350 and all models. G ea Carburetor Air Heat Plate Support Support plate which is used to hold the carburetor air heat plate in place. For the following application: G w/o cylinder ea Oxygen Sensor Plug When retrofitting a carburetor on late model engines, an oxygen sensor is not necessary. This plug seals the oxygen sensor bung on headers and exhaust manifolds. Made from trivalent chromium plated steel with a M-18 thread size to fit most stainless headers M-18 thread plug ea Fuel & Exhaust L Manifold Components 551

25 Exhaust Headers Hedman Hedders Classic Industries stocks a full line of Hedman Hedders for Camaro models. These units are designed to replace the heavy restrictive factory manifolds with tubular steel manifolds to increase horsepower and torque. Includes collector and header to head gaskets, collectors, and bolts. We offer Hedman Hedders for or without air injection (smog tubes). Get more performance from your Camaro without breaking the bank and do it with a name you can trust in the header business Hedman. Important: Available in black only. Be sure to read the important notes listed on the bottom of this page pertaining to each header system for correct application. Note: Shipped oversize OS1 Part# Year Engine See Notes AC PS AT Column AT Floor MT Column MT Floor Smog Notes Tube Dia. Coll Dia. Price Unit , 6, 45, 49, 104, 121 7,26 Y Y Y N Y D,* 1-5/8" 3" set , 5, 6, 45, 49, 104, 121 7,26 Y Y Y N Y F,J 1-5/8" 3" set , 4, 6, 49, 104, 121 7,26 Y Y Y N Y C,J 1-5/8" 3" set ,6,15,45,49,103,121 7,26 Y Y Y N N D,* 1-5/8" 3" set , 5, 6, 15, 45, 49, 103 N Y Y Y N N F,J 1-5/8" 3" set , 4, 6, 15, 49, 103, 121 7,26 Y Y Y N N C,J 1-5/8" 3" set , 6, 45, 49, Y Y Y Y Y D,* 1-3/4" 3" set , 6, 45, Y Y Y N Y D,* 1-3/4" 3" set , 4, 6, 20, 49, 208 Y N Y Y Y Y C 1-3/4" 3" set , 6, 15, 20, 45, 49, 208 Y Y N Y N Y D,* 1-3/4" 3" set , 5, 6, 15, 20, 49, 208 Y Y N Y N Y F,M 1-3/4" 3" set , 4, 6, 15, 20, 49, 208 Y Y N Y N Y C,L 1-3/4" 3" set , 6, 45, 49, 208 Y Y N Y N Y C 2" 3" set , 6, 45, 208 N Y Y Y N Y D,* 2" 3" set ,6,45,103,109,121,135 Y Y Y Y N N D,* 1-5/8" 3" set , 6, 15, 45, 103, 121 Y Y Y Y N Y D,* 1-5/8" 3" set tork step 1, 6, 15, 16, 45, 103, 121 Y Y Y Y N Y D,* 1-1/2"-1-5/8" 3" set , 6, 15, 45, 103, 121, 167 Y Y Y Y N Y 1-5/8" 3" set , 5, 15, 103, 121, 140, 144 Y Y Y Y N Y 1-5/8" stock set LS1 1, 6, 45, full length, stepped Y Y N Y N Y D,* 1-5/8"-1-3/4" 3" set *) Not applicable or intended for street or highway use. Legal only for racing vehicles which may never be used upon a street or highway. ) Currently in E.O. approval processing and not currently covered by any existing E.O. number at this time. A) This hedder has been submitted to the California Air Resources Board for criteria and exemption approval. Pending approval, the E.O. # should be available soon. C) For vehicles 1964 through 1974 without A.I.R. system, considered as OE replacement parts when existing emission controls are not removed from vehicle. D) Not legal for sale or use in California. Hedman Hedder Emission Notes catalog only. Hedman Hedder Notes F) For vehicles 1964 through 1974 with A.I.R. system, considered as OE replacement parts and do not require an E.O. number, when existing emission controls are not removed from vehicle. J) cid without A.I.R., non feedback only. L) cid without A.I.R., non feedback only. M) cid non-feedback only. N) only, 50 state legal for these years. X) T.E.M.S. (Tubular Exhaust Manifold Systems) are 50 state legal for years listed in Fuel & Exhaust L 0) T.E.M.S. Tubular Exhaust Manifold System 1) Without smog injection or injection heads. 4) Includes parts necessary to retain emission devices. (50 state). 5) With A.I.R. system. 6) Modifi cation to stock exhaust required to retain catalytic converter. 7) Will not fi t Camaro with AC. 15) Shortie hedder (Max. ground clearance). 20) Not recommended for aluminum heads. 26) 70 or later only AC equipped vehicles require bracket # (A6 compressor). 30) Dog leg port only. 31) Must use non-shell motor mounts. 45) Not legal for sale or use in California on pollution controlled motor vehicles. 49) Will not fi t Saginaw close ratio PS with 825 power steering box, ) Will fi t with angle plug heads (Chevy alum. only) 104) It may be necessary to remove Z bars (SS). 109) Dual exhaust only. Limited ground clearance. 121) Must modify rotary AC bracket. 131) Chevy engine. 135) Transmission limited to 700R4 and TH ) Replace Y-pipe available. 144) Complete with Y-pipe to single catalytic converter. 145) Complete with dual Y-pipe to dual catalytic converter. 163) Stepped hedder with equalizer Y-pipe. 167) Must use oxygen sensor reducers, not supplied with hedders. 203) Non-EGR equipped. 204) With EGR. 205) With precatalytic converters. 206) Will not fi t engines with precatalytic converters. 208) Due to cylinder heads (aluminum) generation 6 engines, 502 BB Chevy will have clearance problems with some applications. Bottom of hedder fl anges may hit head bolts. Notching may be necessary. 234) Designed with additional clearance for close ratio steering boxes. 552 Exhaust Headers Toll Free Order Line

26 Exhaust Headers Doug s Headers Doug s headers are carefully developed to fit each specific vehicle application. Doug s headers are available for Camaro models with small block or big block V8 engines, with and without air-injection ports, and with console or column shifters. Heavyduty machined and finished header flanges, the smooth mandrel bends tubes, and a protective Metallic Ceramic Thermal Barrier Coating (MCTBC) make Doug s 8304 Headers an excellent choice for exhaust system performance. Important: These headers are intended for off-highway use only and are not designed for California vehicles with pollution control devices. Be sure to read the important notes listed on the bottom of this page pertaining to each header system for correct application. Note: Shipped oversize. OS Engine Smog Tube Cell AC PB PS AT AT MT MT See Notes Diameter Diameter Col. Floor Col. Floor Rectangular Port A 1 7-8" 3-1/2" N Y Y Y Y N Y set Same As Cylinder Head Port A 1 3/4" 3" N Y Y N Y N Y 36,52,92, set A 1-3/4" 3" Y Y Y Y Y N Y 92,95, set A 1-7/8" 3-1/2" N Y Y Y Y N Y set Oval Port A 1 5/8-2" 2 1/2" Y Y Y N Y Y Y 36,61,92,96,126, set A 1 5/8" 3" Y Y Y Y Y N N 5,36,52,61,92,93,96,202, set A 1 5/8" 3" Y Y Y N Y N Y 36,61,92,93,96, set Engine Round Port A 2-1/8" 3-1/2" N Y N Y Y N Y set Same As Cylinder Head Port A 2" 3 1/2" Y Y Y Y Y N Y 69, set A 1-7/8" 3-1/2" N Y Y Y Y N Y set A 1 3/4" 3" Y Y Y N Y N N 52,69, set A 1 3/4" 3" Y Y Y N Y N Y 5,52,69, set Doug's Headers Notes 5) Shorty design for maximum ground clearance. 36) Fits D-port cylinder heads including ZZ4 crate engines. 52) Will not fi t with Saginaw close ratio 825 steering box. 61) Does not fi t Camaro with AC 69) Big block frame stands and motor mounts must be used to insure proper engine location and header fi t. 92) Will fit most angle plug heads including factory Chevrolet Bow Tie heads. 93) Requires removal or modifi cation of locking steering columns if equipped. 95) Reducers available with O2 sensor fi ttings. 96) Installation requires a left side AC bracket and later vehicles with short compressors can use the stock bracket. 126) Tri-Y design. 133) Does not fi t with power glide transmission. 202) Will fit with Detroit Speed & Engineering front subframes with rack and pinion steering. 214) Must use non-shell type motor mounts. 227) Will fi t with Saginaw close ratio 825 steering box. A) The product accompanying this document is legal only for off-highway use (except in California or states that have adopted California emission standards), racing use or for pre-emission controlled motor vehicles/motor vehicle engines (pre-1974 domestic vehicles certifi ed to California standards, pre-1974 domestic vehicles certifi ed to federal standards and all pre-1974 foreign vehicles), per the manufacturer s application guide LS Headers These headers are designed for the LS engine mounting kits and are available in a variety of sizes and styles for 4.8L, 5.3L and 6.0L LS engines. A silver ceramic coating keeps temperatures under control and provides a great long-lasting appearance. Designed to clear the factory AC box, power steering, power brakes, crossmember, and oil pan when installed with a LS conversion kit. Made in the USA. Note: Some modifi cation may be necessary when used with 4L80E transmissions or column shifters. Not legal on pollution controlled vehicles. Mid-Length Headers /4" set /4" set /4" set Long Tube Headers /4" set /8" set " set /4" set /8" set " set /4" set /8" set " set Stepped Long Tube Headers /4 to 1-7/8" set /8" to 2" set /4" to 1-7/8" set /8" to 2" set /4" to 1-7/8" set /8" to 2" set P Borla Stainless Steel Headers Get the power and torque you ve been looking for! These Borla headers provide maximum power, efficiency, and stunning looks. These headers feature 2" primary tubes and 3" collectors. Includes 2-1/2" collector adapters. Manufactured from stainless steel and backed by a 1,000,000-mile warranty. Note: Shipped oversized. BA /427 cid set Camaro Pypes Big Block Headers Pypes big block headers feature large 2" primary tubes and 3.5" collectors with power spikes. Constructed of 304 mandrel bent stainless steel and fully TIG welded they include stainless collector reducers, premium hardware, and gaskets. Big block frame mounts and motor mounts must be used to ensure proper engine location and header fitment. Fits 6-speed ZF transmission and standard 5-speed Chevy 502 big block generation 6 engines with aluminum cylinder heads will have clearance problems on some applications. Bottom of header flanges may hit head bolts requiring notching to clear the bolts. Note: Will not fi t Saginaw close ratio power steering with 825 power steering box. A set P1046 Pypes Header Collector Reducers These welded, 12" extended length reducers connect your headers directly to your Pypes X-pipe to eliminate unnecessary seams, clamps and extra work. They are constructed of polished 304 stainless steel. Limited lifetime warranty. P1044 3" header flange to 2.5" pipe pr P1045 3" header flange to 3" pipe pr P " header flange to 3" pipe pr P " header flange to 2.5" pipe pr Fuel & Exhaust L Exhaust Headers 553

27 Exhaust Components Fuel & Exhaust L Manifold Bolt and Stud Correct style exhaust manifold bolt and stud set will replace the rusted or broken originals. Includes: 1 long bolt, 3 medium length bolts, 7 short bolts and 1 stud SB, AC set AR4111 AR1111 K OE Manifold Bolt Sets If you re seeking originality for your underhood restoration, don t settle for anything less than this complete set of OE type bolts and stainless steel washers to mount your exhaust manifolds. Available for small block or big block. K SB, 24 pc set K BB, 32 pc set Header Bolt Sets The compact 12 point nut version lets you easily slip a socket close to the pipe. Each ARP bolt set includes the specific number of parts for your application, plus premium quality washers and hex or 12 point nuts, as required. Each small block set contains 12 bolts and each big block set contains 16 bolts. Made in the USA. Small Block 3/8" Dia. Hex Head Bolts AR1111 black 3/4" set AR4111 stainless 3/4" set AR11111 black 1" set AR41111 stainless 1" set Small Block 3/8" Dia. 12 Point Bolts AR1121 black 3/4" set AR4121 stainless 3/4" set AR11211 black 1" set AR41211 stainless 1" set Big Block 3/8" Dia. Hex Head Bolts AR1112 black 3/4" set AR4112 stainless 3/4" set AR11112 black 1" set AR41112 stainless 1" set Big Block 3/8" Dia. 12 Point Bolts AR1122 black 3/4" set AR4122 stainless 3/4" set AR11212 black 1" set AR41212 stainless 1" set Manifold To Pipe Stud Reproduction studs and nuts used to attach the exhaust pipes to exhaust manifold. Each set includes a complete set of studs for the installation of both exhaust manifolds. Includes: 3 short and 3 long studs. K set C Flames D Bow Tie G 350 H 454 E SS Exhaust Bolt Sets Dress up your full size Chevrolet with these one-of-a-kind dress-up bolt sets. The Chevrolet Bow Tie, SS or flames logo is stamped directly onto the head of the bolts. They are available in decorative chrome-plated or polished stainless steel. Note: Must specify logo prefi x: C Flames, D Bow Tie, E SS. Chrome Header Bolts 56461C SB set 56418C SB 1" set 56477C std exh set 56488C BB set 56498C LT set Stainless Steel Header Bolts 56461S SB set 56418S SB 1" set 56477S std exh set 56488S BB set 56498S LT set Exhaust Bolts Reproduction of the exhaust manifold bolts for big block engines from These are black, hardened bolts that feature the correct flanged head, just like original. Set of 16 bolts BB set AK118A Header Bolt Set Includes all original style hex head bolts for small block or big block headers. Choose from polished stainless or chrome. Small block sets include 12 bolts and big block sets include 16 bolts. AK119A SB chrome set AK119B SB stainless set AK118A BB chrome set AK118B BB stainless set Exhaust French Locks Beautiful reproduction of this commonly removed or discarded engine component. This item is necessary to help keep exhaust manifold bolts from backing-out and possibly being lost. A must for the true engine detailer. PR1027K BB set PR1161K SB set 554 Exhaust Hardware Toll Free Order Line PR1027K Small Head Header Bolt Sets These 12 piece small head bolt sets are designed to replace regular hex head bolts for easier access and fewer skinned knuckles. Available in both black oxide and zinc finishes. Black Oxide Hex Head /8"-16 x 3/4" set /8"-16 x 1" set Zinc Hex head /8"-16 x 3/4" set /8"-16 x 1" set Aluminum Header Gasket Set Soft conforming aluminum gaskets easily conform to the header flanges for a superior seal. Each set comes with 2 gaskets SB, square port pr BB, round port pr A L EGR Block Off EGR intake and exhaust block off plates for Camaro models with a 3.8L V6. This kit includes two EGR plates, one for driver side exhaust manifold and one for the intake manifold. Available with either a machined or black anodized finish. Includes installation hardware. A kit A black kit EGR Delete Kit EGR and cold start delete kit for Camaro models equipped with an L98 TPI 305/350. The five piece kit allows you to delete the EGR valve and cold start injector from your TPI intake, and also includes a custom aluminum throttle body plate. The cold start delete kit includes injector delete plate and fuel rail plug. Made from 6061-T6 aluminum with a machined finish. Includes gaskets and mounting hardware. Complete EGR/Cold Start Delete Kit A kit A kit Cold Start Delete Kit A kit A kit A LT1 Smog Plugs Billet aluminum smog/air block off plugs for Camaro models with a LT1. Made from 6061 aluminum and designed to plug the air injection ports in both exhaust manifolds. Note: For 1995 cars, please check your manufacture date before ordering. A E pr A L pr LT1 EGR Block Off Kit Billet EGR block off plate kit for Camaro models equipped with a LT1. This kit includes the 3 necessary plates needed for the elimination of the EGR system. Machined from 6061 aluminum for a precise fit and clean finish. Includes gaskets and mounting hardware. A kit L98 EGR Delete Kit EGR delete kit for Camaro models equipped with an L98 TPI 305/350. This EGR block off kit includes both the EGR and exhaust tube block off plates. Made from 3/8" thick 6061-T6 aluminum. Includes gaskets and mounting hardware. A kit

28 Exhaust Components Replacement Smog Pumps These remanufactured smog pumps will replace the original exactly. Choose from 6 or 8 cylinder pumps. Classic Industries offers the largest selection of smog parts anywhere! Pulley not included A 6 Cylinder 11132A ea ea ea V , 3.8L ea , 3.8L ea , 3.8L ea , 3.8L ea V ea 11132A , 396, ea , 327, 396, ea , 400, 454, ea , 350, 400, ea , 305, ea ea without police/taxi ea with police/taxi ea with FD stamp ea with FC stamp ea except with ML stmp ea with ML stamp ea ea without AC ea with AC ea without AC ea with AC ea ea ea , ea A970142B A970143B LS1 EGR Block Off Kit Billet EGR smog block off plate kit for Camaro models equipped with an LS1.The complete kit includes one intake block off, one EGR block off plate for the RH exhaust manifold, and 2 smog block off plates for both LH and RH exhaust manifolds. Components can also be purchased separately. Offered with machined or black anodized finish. Includes gaskets and mounting hardware. Note: *1 required. 2 required Complete Kit A970140A plain kit A970140B blk kit 3-Piece Exhaust Block Off Kit A970141A plain kit A970141B blk kit Intake Block Off Plate A970142A* plain ea A970142B* blk ea Exhaust Air-Injection Block Off Plate A970143A plain ea A970143B blk ea Exhaust EGR Block Off Plate A970144A* plain ea A970144B* blk ea Smog Pump Bracket Reproduction or original GM smog pump bracket for models. Used to support the smog pump. Reproduction SB ea Original GM G , ea G ea Smog Pump Belts Correct reproduction A.I.R. smog pump belts for Camaro models. These unique reproduction belts are designed to offer an original style replacement that includes the correct markings for an authentic and original reproduction replacement. Each belt is officially licensed by General Motors as an authentic replacement B /327 no AC ea B /327 AC ea B w/ TH ea B /427 no AC ea B /427 AC ea B /327 no AC ea B /327 AC ea B /427 no AC ea B /427 AC ea Smog Pump Pulley Quality reproduction of the deep groove A.I.R. (air injection reactor) pump pulley for high performance small block and big block models. Single groove, 5-3/4" o.d. K1132 K /325HP ea K /375HP ea K Z/ ea K Z/ ea K /375HP ea K Z/ ea R Smog Tubes Also known as air injection reactor tubes (A.I.R. tubes), these reproduction smog tubes are manufactured from zinc plated steel to factory specifications with correct bends and outlets and semigloss black finish. A correct threaded outlet head is installed for easy installation of the smog pump check valves. R pr R pr R pr R pr R pr R pr R pr R no AC pr K Smog Check Valves GM replacement or reproduction of the smog pump check valve used on many Chevrolet models. K repro ea E repro ea G SB ea G exc ea E ea G ea Extension Tubes Reproduction A.I.R. extension tubes which fit in the exhaust manifold port under the main A.I.R. tube assembly. E SB ea Air Injection Eliminator Plug Correct block off plug used when converting currently produced exhaust manifolds with holes for air injection tubes back to pre-smog usage. EMP330 all ea Diverter Valve Tee Original air injection valve tee for models. G all ea Smog Diverter Elbow Reproduction diverter elbow for the smog pump. This is the OEM aluminum elbow that bolts to the smog pump, and the diverter valve mounts on the opposite side. Used on most Chevrolet applications LS6, LS5, L78, L89, 302, 350, 396, and 454 engines ea Air Injection Hoses Sets include hoses to check valve on AIR tube. Correct lengths of thick walled hoses to replace missing or cracked originals. Includes 4 correct tower hose clamps for mounting. Note: *Check valve style Complete Hose Kits SH SB set K BB set K BB set Hose Only ea * ea * ea Hose Tower Clamps Reproduction tower design smog pump hose clamp for all vehicles. Featuring the correct 1-1/6" diameter size. As required ea Warning: Concerning Smog Pump Pulleys Stock replacement, aftermarket stamped steel or cast iron pulleys are not designed to exceed 400 horsepower or 6000 RPM. Using reproduction pulleys on engines in excess of these limits may result in catastrophic disintegration of the pulley causing severe damage to the engine, cooling system and body parts. Classic Industries assumes no liability for damages caused by improper usage of pulleys. Please be sure to install the pulley properly to avoid damages that could occur from improper installation or exceeding the recommended RPM limitations. Exhaust Hardware SH Fuel & Exhaust L

29 Exhaust Components Soft Conforming Aluminum Collector Gasket Set Soft conforming aluminum gaskets easily conform to the collector flanges for a superior seal. Each set comes with: 2 gaskets, six nuts and bolts /2" collector set " collector set /2" collector set Manifold Pipes Manifold pipes designed to fit OEM exhaust manifold and facilitate the installation of a performance exhaust system. Pipes are manufactured in corrosion resistant stainless steel. Features 2.5" tubing and a 3 bolt flange connection. Made in the USA. Note: Shipped oversize. OS small block set P Pypes Manifold Down Pipes Not all performance enthusiasts use collector style headers, so Pypes has designed 2-1/2" downpipes for log style, rear exit exhaust manifolds to fit your Pypes header back systems. These down pipes are made from 409 stainless steel and mandrel bent 16 gauge tube that fit directly onto factory cast iron manifolds, and slip into the header back systems. Manifold flanges are already installed. Note: Shipped double oversize. Small Block Models OS2 P ", 3 bolt pr P ", 2 bolt pr Big Block Models P ", 3 bolt pr F15920 Universal Balance Pipe Set Flowmaster offers a pre-fabricated universal balance pipe set to ease the installation of a crossover pipe in a dual-exhaust system. Set includes: T-pipe connectors, balance pipe and clamps. F " set P Pypes Tunnel X-Crossover Since a V8 fires alternately, exhaust exits in pulses rather than a steady flow. While one pipe is filled with pressure the other pipe is relatively pressureless, but connecting the two pipes in a Siamese pattern allows pressure to be equalized between the two tailpipes. This action allows the exhaust to pass through quicker for better breathing that increases horsepower. The Pypes crossover product line is defined by a highquality, exceptionally versatile design. They are a proven winner when it comes to bumping up the horsepower of your daily driver or race car. Pypes tunnel X-crossover fits a variety of Camaro models with easy installation. All crossovers are made of 409 stainless steel with dual reinforcement plates at the welds where they are needed most. All pipes are mandrel bent to allow for the maximum flow of exhaust gasses, which boosts acceleration. Limited lifetime warranty. Important: Modifi cation to the body pan brace is required on convertible models. In order to utilize this X-pipe, it is necessary to either add a body pan designed to allow clearance for the X-pipe assembly, or remove the body pan and install subframe connectors. If using stock, cast iron manifolds, add a set of downpipes to connect your original manifolds to the header back system. Note: Shipped oversize. OS1 P /2" ea P " ea P1077 Fuel & Exhaust L Manifold Y-Pipes These Y-pipes are manufactured in 100% stainless steel and designed to complement crossmember back exhaust systems. Mates to OEM manifolds and fits to 2.5" tubes. Made in USA small block ea small block ea Tru-X And Y-Pipes The more gentle radius of these X and Y pipes allow for better exhaust gas scavenging, noise cancellation and better balance between cylinder banks. The result is a significant increase in power and torque, but a reduction in db sound levels. X-Pipe /2" dual in/out x 9.5" long ea " dual in/out x 13.2" long ea Crossover /4" dual in/out x 12" long ea /2" dual in/out x 12" long ea " dual x in/out x 14" long ea Y-Pipe /2" single, 2" dual ea /2" single, 2-1/4 dual ea /2" single, 2-1/2 dual ea " single, 2-1/2 dual ea " pipe, 3" dual ea Pypes X-Crossover Dump Legs These dump legs replace the front legs of the X-pipe crossover. Strategically located for maximum ground clearance. All dump legs include block off plates and hardware. Manufactured in 409 stainless steel with mandrel bends to allow for the maximum flow of exhaust gasses. P /2" set P " set F15923 Header Collector Ball Flange Set This header collector set takes the place of messy three bolt, flange type connections and allows for a leak-free and gasket-free ball flange type connection. F " collector to 3" system set F " collector to 2.5" system set 556 Exhaust Components Toll Free Order Line

30 Exhaust Components " Camaro Tailpipe Set Flowmaster s 3" mandrel bent tailpipe set covers Camaro models. This tailpipe set is designed so you can create a mandrel bent custom high performance exhaust for any Camaro including convertibles. Designed to exit between the tires and rear bumper on either side of the vehicle. Note: Hardware and hangers are not included. F set Borla Dual Exhaust Give your Camaro a deep throaty growl to match its aggressive looks with a Borla high flow exhaust system. Featuring 2-1/2" mandrel bent tubing with H-pipe and low restriction single flow mufflers, these systems reduce back pressure to improve performance. Use with factory exhaust manifolds or Borla headers. Manufactured from high-quality stainless steel and backed by a 1,000,000-mile warranty. Note: Shipped double oversize. BA /427 cid set Aluminized Tailpipes OEM style tail pipes which are aluminized offering a superior appearance to the coated style originals. Long-lasting and effective against salt road winters. Note: *With dual chrome tips. Intermediate Pipes LH ea RH ea Tail Pipes, Single Exhaust ea cylinder ea ea ea ea Tail Pipes, Dual Exhaust E LH ea E RH ea E LH and RH pr LH ea RH ea * LH ea * RH ea LH, 305H 4bbl ea RH, 305H 4bbl ea LH, 305G,F 4bbl ea RH, 305G,F 4bbl ea DF Direct Fit Exhaust Systems Installing a high-performance exhaust system for your later model Camaro has never been easier! This 2-1/2" direct fit system follows the OEM routing and mounting points exactly so you don t have to cut and weld brackets and pipes. Now you can bolt-on a complete high-performance system featuring your choice of the power boosting Super Turbo muffler or the Ultra Flo SS muffler. Important: *Except dual catalyst converter models. Note: Engine is the 8th digit of the VIN. Shipped oversize. OS1 Super Turbo Systems DF code H or E (exc HO) kit DF code G or F kit DF112 * code G, F or kit DF code F or 8 w/dual cats kit Ultra Flow SS Systems DF code H or E (exc HO) kit DF code G or F kit DF116 * code G, F or kit DF code F or 8 w/dual cats kit 1969 Exhaust Hanger Mount Plate Reproduction stamped steel exhaust hanger mount plate for 1969 Camaro models with factory dual exhaust. This bracket mounts to the frame rail providing a mounting location for the rear exhaust hanger. KW LH ea Super Turbo Exhaust Components High-performance pipe which is aluminized offering a superior appearance and was designed to follow the OEM routing and mounting points exactly. This intermediate pipe runs from the muffler to the tail pipe Important: Your Camaro s engine is the 8th digit of the VIN. Note: Shipped oversize. Intermediate Pipes OS code H or E ea code G or F ea code G or F ea code F or 8, dual ea Tail Pipes LH ea RH ea HC92 HC OEM Style Muffl er Clamps Correct replacement muffler clamps are designed to replace the factory originals. Each clamp includes hardware. Either 2" or 2-1/4" pipes. Standard Clamp HC with 2" ea HC with 2-1/4" ea Guillotine Clamp HC with 2" ea HC with 2-1/4" ea Replacement Style And Stainless Clamps Correct replacement style clamps for applications. Each clamp is listed as standard style or heavy-duty Replacement Style " clamp std 5/16" U-bolt 1.99 ea " clamp hd 3/8" U-bolt ea /4" clamp std 5/16" U-bolt 1.99 ea /4" clamp hd 3/8" U-bolt ea /2" clamp hd 3/8" U-bolt ea " clamp hd 3/8" U-bolt ea Stainless Steel E240 2" clamp stainless ea E /4" clamp stainless ea E /2" clamp stainless ea E243 2" clamp plated ea E /4" clamp plated ea E /2" clamp plated ea Original GM Exhaust Clamps Original factory replacement exhaust pipe clamps which are superior to aftermarket clamps. These clamps include the U-bolt, clamp closeout and two attachment nuts. Excellent for the hard core restorer. G /2" clamp ea Tailpipe Expander Used to remove clamp grooves and round out crushed or bent exhaust pipes to ensure a tight fit, eliminating exhaust leaks. The hex end allows the use of a combination wrench to remove clamp grooves or small imperfections, or an impact wrench to expand pipes. Imperfections are forced outward rather than forward, eliminating possible damage to component parts. No holding fixture is necessary. X /16" to 2-1/2" pipes ea Exhaust And Tailpipe Cutter Cuts pipes 3/4" to 3" (19mm to 76mm) in diameter. 15 blades effectively cut pipe so only 1/4" turn is needed for complete cut. Works great in hard to reach areas. X ea Fuel & Exhaust L Exhaust Components 557

31 Mufflers E Dynomax Super Turbo Muffl er Exclusive patented flow directors channel exhaust flow and eliminate turbulence, larger diameter internal tubes for maximum flow, along with fiberglass matting that delivers a mellow, true performance sound. All aluminized materials, double wrapped and arc-welded for longer life and sharper appearance. All universal mufflers are reversible for custom installation V /2" inlet offset/dual outlet ea 5" x 8" Offset/Offset V6 Muffl er 100% stainless steel mirror finish muffler for V6 Camaro models. 21" overall length and body length of 14". Made in the USA. Note: Fits V6. Non-reversible. Polished Stainless Steel Muffler " 2.5" ea Fuel & Exhaust L Transverse Dual Exhaust Muffl ers Correct replacement transverse mounted dual exhaust mufflers for models. With Dual Inlet small block ea E " o.l ea With Single Inlet H w/4 barrel ea G,F w/4 barrel ea Z28 Muffl er Correct replacement dual exhaust mufflers for Z28 models with 305 or 350 V8. Single, offset inlet and outlet. Fits LH or RH side LH or RH ea Dynomax Ultra Flo SS Muffl er Uses a unique straight through design that maximizes flow and power. Made from all stainless steel materials for corrosion resistance. Includes high chromium content, high-luster T-304 cover and heads. Continuous perf design maximizes sound absorption, minimizes turbulence and gives a deep powerful true performance sound. All universal mufflers are reversible for custom installation V8, V /2" inlet offset/dual outlet ea Terminator Muffl er Flowtech s Terminator is constructed entirely of super thick, black aluminized steel, fully welded for strength and durability with 3" inner pass tubes that reduce back pressure and increase horsepower like no other muffler can. Note: Dimensions: 15" x 11" x 5" Direct Fit /2" offset/offset dual ea F53083 F42583 Flowmaster Transverse 80 Series Muffl ers The 80 Series is designed for applications where the muffler must be mounted transversely (cross-flow) behind the rear end. It provides an aggressive muscle car sound both inside and outside the vehicle. A replacement for early and late model Camaro models. Constructed of 16 gauge aluminized steel and fully mig-welded for maximum durability. Center Inlet/Center Outlet F " 4" x 9.75" x 24" ea Single Inlet/Dual Outlet F " 4" x 9.73" x 21" ea F "/2.5" 4" x 9.73" x 21" ea F "/2.5" 5" x 10" x 23" ea Magnafl ow Oval Case Muffl ers Magnaflow s wide-open performance mufflers outflow OEM chamber style mufflers by as much as 167%! This reduces engine heat and back pressure and improves exhaust scavenging from the combustion chamber. Magnaflow minimizes the power robbing effects of the OEM system to restore torque and horsepower to the engine. Magnaflow is the straight through, wideopen performance muffler with a smooth, deep tone. Made in the USA. Stainless Steel Mufflers Center Inlet/Center Outlet " 2" ea " 2.25" ea " 2.5" ea " 3" ea Center Inlet/Offset Outlet " 2" ea " 2.25" ea " 2.5" ea " 3" ea Offset Inlet/Dual Outlet " 2.5"/2.25" ea " 2.5"/2.5" ea " 3"/2.5" ea Polished Stainless Steel Mufflers Center Inlet/Center Outlet " 2" ea " 2.25" ea " 2.5" ea " 3" ea " 3-1/2" ea " 4" ea Offset Inlet/Dual Outlet " 2.5"/2.25" ea " 3"/2.5" ea Center Inlet/Offset Outlet " 2.25" ea " 2.5" ea " 3" ea Offset Inlet/Offset Outlet " 2.25" ea " 2.5" ea " 3" ea 558 Mufflers Toll Free Order Line

32 Mufflers Magnafl ow Circular Muffl ers Magnaflow circular case mufflers. Available in two sizes and regular or mirror finish stainless steel. Made in the USA. Stainless Steel Mufflers 4" x 4" Mufflers " 2.5" ea 5" x 5" Mufflers " 2.5" ea " 3" ea Polished Stainless Steel Mufflers 4" x 4" Mufflers " 2.5" ea " 3" ea 5" x 5" Mufflers " 2.5" ea " 3" ea Thrush Glasspack Muffl ers Thrush mufflers have a straight through, smooth flowing, perforated center tube design for maximum flow and power. Made of a heavy gauge shell for durability. Feature expandable bushings for custom applications. Enjoy the unmistakable sound of a Thrush glasspack muffler today. Note: Dimensions: overall length x shell length x shell diameter " 25" x 20" x 3-1/2" ea " 27" x 22" x 3-1/2" ea " 31" x 26" x 3-1/2" ea /4" 25" x 20" x 3-1/2" ea /4" 27" x 22" x 3-1/2" ea /4" 31" x 26" x 3-1/2" ea /2" 28" x 23" x 4" ea /2" 45" x 40" x 4" ea Magnafl ow Glasspack Muffl ers Magnaflow Glass Pack Mufflers feature a free-flowing, straight through perforated core, and Rockwool acoustical packing material to deliver a smooth, deep tone to ensure long life and no sound degradation over time. Available in sizes from 2"-3" diameter. Made in the USA " 22" x 18" x 3.5" ea " 26" x 22" x 3.5" ea " 30" x 26" x 3.5" ea " 22" x 18" x 3.5" ea " 26" x 22" x 3.5" ea " 30" x 26" x 3.5" ea " 30" x 26" x 4" ea " 22" x 18" x 4" ea Flowtech Terminator Muffl ers Flowtech s Terminator is constructed entirely of super thick, black aluminized steel, fully welded for strength and durability with 3" inner pass tubes that reduce back pressure and increase horsepower like no other muffler can. Dimensions: 15" x 11" x 5". Universal Fit Inlet /Outlet /4" center/offset ea /2" center/offset ea " center/offset ea Universal Fit Raptor Muffl ers Flowtech s new Raptor turbo performance muffler features a unique sound rib case design and aluminized, lock seal construction. Low restriction, reduces back pressure and increases performance. Dimensions 13" x 10" x 4 1/2" with offset-inlet/center-outlet " ea /4" ea /2" ea Dynomax Universal Super Turbo Muffl ers Exclusive patented flow directors channel exhaust flow and eliminate turbulence, larger diameter internal tubes for maximum flow, along with fiberglass matting that delivers a mellow, true performance sound. All aluminized materials, double-wrapped and arc-welded for longer life and sharper appearance. All universal mufflers are reversible for custom installation. Important: Sport model from 2" to 2-1/2" measures: 4" x 9-3/4" x 18-1/2" and 3" measures: 4" x 9-3/4" x 20", Street model measures: 4" x 9-3/4" x 25-1/2". Sport " inlet offset/center outlet ea " inlet offset/offset outlet ea /4" inlet offset/center outlet ea /4" inlet offset/offset outlet ea /2" inlet offset/center outlet ea /2" inlet offset/offset outlet ea /4" inlet offset/center outlet ea " inlet offset/center outlet ea " inlet offset/offset outlet ea Street /4" inlet center/offset outlet ea /4" inlet offset/center outlet ea /2" inlet center/offset outlet ea /2" inlet offset/offset outlet ea /2" inlet cntr/offset dual outlet ea Dynomax Universal Ultra Flo SS Muffl ers Uses a unique straight through design that maximizes flow and power. Made from all stainless steel materials for corrosion resistance. Includes high chromium content, high luster T-304 cover and heads. Continuous perf design maximizes sound absorption, minimizes turbulence and gives a deep powerful true performance sound. All universal mufflers are reversible for custom installation. Important: This muffl er comes in two styles: Sport model measures: 4" x 9-3/4" x 18-1/2", Street model measures: 4" x 9-3/4" x 25-1/2". Sport /4" inlet offset/center outlet ea /4" inlet offset/offset outlet ea /2" inlet offset/center outlet ea " inlet ctr/2-1/2" offset dual outlet ea Street /2" inlet offset/center outlet ea P1021 P1030 Pypes Stainless Muffl ers Pypes has learned that no one muffler design is best. Every car is different, and everyone has different requirements. Street Pro mufflers are chambered to maintain rich sound without resonance. Race Pro have a straight through design. Violator mufflers have an internal louvered tube with mini sound deflector chambers, making it flow ike a straight through muffler but with the sound of a chambered muffler. Each muffler measures 4" x 9" x 14" long. Street Pro 409 Stainless Steel P " offset/offset ea P " offset/center ea P1023 3" offset/offset ea P1024 3" offset/center ea Race Pro 409 Stainless Steel P " offset/offset ea P " offset/center ea P1031 3" offset/offset ea Violator 409 Stainless Steel P " offset/offset ea P " offset/center ea P1040 3" offset/offset ea Fuel & Exhaust L Mufflers 559

33 Mufflers Fuel & Exhaust L A Dr. Gas Frame Clearance Tubes Frame clearance tubes allow you to route your exhaust through tight areas under crossmembers and frame rails. They are designed with round openings and a larger diameter low profile oval center section that gives extra clearance without a loss of cross sectional area or flow. Available for 2.5", 3", or 3.5" diameter pipe. Made in USA. A " clearance tube ea A " clearance tube ea A " clearance tube ea A A Dr. Gas FreqMod Heavy-Duty Muffl er Dr. Gas FreqMod Heavy-Duty mufflers are designed for severe applications such as high horsepower engines running headers, superchargers or large single exhaust systems. The patented two stage design reduces popping and rasp for a mellow tone while maintaining a very high flow rate. Mufflers are available in high temperature black and copper colored finishes. Made in USA. 2.5" Center Inlet/Offset Outlet A black 14" x 10" x 3.5" ea A copper 14" x 10" x 3.5" ea 3" Center Inlet/Offset Outlet A black 14" x 10" x 3.5" ea A copper 14" x 10" x 3.5" ea A black 14" x 10" x 4.5" ea A copper 14" x 10" x 4.5" ea 3.5" Center Inlet/Offset Outlet A black 14" x 10" x 4.5" ea A copper 14" x 10" x 4.5" ea A A Dr. Gas SpinPro 4 Trap Muffl er The compact four trap muffler offers the smooth flow and throaty exhaust sound of the Dr. Gas SpinPro mufflers in a square design that fits into tight spaces. They feature an extremely rugged construction with high temperature black and copper colored finishes. Made in USA. 2.5" Center Inlet/Center Outlet A black 14.5" x 6.5" x 3.25" ea A copper 14.5" x 6.5" x 3.25" ea 3" Center Inlet/Center Outlet A black 14.5" x 6.5" x 4.25" ea A copper 14.5" x 6.5" x 4.25" ea A A Dr. Gas FreqMod Muffl er Make your V8 sound like an exotic sports car! Dr. Gas FreqMod mufflers modify the frequency to increase the pitch of your exhaust note. These compact mufflers fit most applications while offering exhaust flow comparable to the best performance mufflers. They should be used with an X-pipe for best results. Intended for extreme or race applications. Mufflers are available in high temperature black and copper colored finishes. For quieter application use Heavy- Duty FreqMod mufflers. Made in USA. 2.5" Offset Inlet/Center Outlet A black 8.5" x 8.5" x 3.25" ea A copper 8.5" x 8.5" x 3.25" ea 3" Offset Inlet/Center Outlet A black 9.5" x 9.5" x 4.25" ea A copper 9.5" x 9.5" x 4.25" ea A A Dr. Gas SpinPro Reverse Flow Muffl er Dr. Gas SpinPro Reverse Flow mufflers feature inlets and outlets on the same end. Perfect for side exit systems with Boom Tube tips or where special routing is required. They feature very rugged construction and are available in high temperature black and copper colored finishes. Made in USA. 2.5" Offset Inlet/Offset Outlet A black 11.75" x 8.75" x 3.75" ea A copper 11.75" x 8.75" x 3.75" ea 3" Offset Inlet/Offset Outlet A black 11.75" x 8.75" x 3.75" ea A copper 11.75" x 8.75" x 3.75" ea A A Dr. Gas SpinPro 5 Trap Low Profi le Muffl er Only 3 thick! These mufflers produce an extremely smooth deep tone at a moderate volume level. In flow bench tests, these mufflers have shown the same performance as straight pipe of the same inlet/ outlet diameter. They feature an extremely rugged construction and are available in high temperature black and copper colored finishes. Made in USA. 2.5" Offset Inlet/Offset Outlet A black 18" x 7.5" x 3" ea A copper 18" x 7.5" x 3" ea 3" Offset Inlet/Offset Outlet A black 18" x 7.5" x 3" ea A copper 18" x 7.5" x 3" ea A A Dr. Gas SpinPro 3 Trap Muffl er These amazingly compact mufflers are very effective against rasp and popping while delivering a very smooth, deep tone. Flow rates are comparable to straight through mufflers. Their extremely rugged construction utilizes fully welded 14 and 16 gauge aluminized steel with high heat coatings. Available in black or a copper that looks great on rear mount applications where mufflers are visible. Made in USA. 2" Offset Inlet/Offset Outlet A black 12" x 6.5" x 3.25" ea A copper 12" x 6.5" x 3.25" ea 2.5" Offset Inlet 2" Offset Outlet A black 12" x 6.5" x 3.25" ea A copper 12" x 6.5" x 3.25" ea 2.5" Offset Inlet/Offset Outlet A black 12" x 6.5" x 3.25" ea A copper 12" x 6.5" x 3.25" ea A black 12" x 6.5" x 4.25" ea A copper 12" x 6.5" x 4.25" ea 3" Offset Inlet 2.5"Offset Outlet A black 12" x 6.5" x 4.25" ea A copper 12" x 6.5" x 4.25" ea 3" Offset Inlet/Offset Outlet A black 12" x 6.5" x 4.25" ea A copper 12" x 6.5" x 4.25" ea 3.5" Offset Inlet 3"Offset Outlet A black 12" x 6.5" x 4.25" ea A copper 12" x 6.5" x 4.25" ea 3.5" Offset Inlet/Offset Outlet A black 12" x 6.5" x 4.25" ea A copper 12" x 6.5" x 4.25" ea 560 Mufflers Toll Free Order Line

34 Mufflers A A Dr. Gas Boom Tubes Dr. Gas Boom Tubes were designed for stock car racing, and now these low profile side exit exhausts are available for your muscle car. Boom Tubes have no restriction and are a perfect add-on for exhaust cutouts. Boom Tubes are fully MIG welded and can be trimmed to match your vehicle s side profile. Untrimmed Boom Tubes measure approximately 27.5" long and are available with 2.5", 3" and 3.5" round inlets. From the inlet transition, they drop to a thin 1.75" thick and 8" wide with two lengthwise support ribs. Exposed exit is approximately 12" to 14" wide depending on the trim angle. Combine with Dr. Gas mufflers and X-pipe system for a one-of-a-kind exhaust sound! Made in USA. Note: Test fi t before trimming. No returns accepted once Boom Tubes are trimmed or altered. Single Boom Tubes A " inlet ea A " inlet ea A " inlet ea Boom Tube Pairs A " inlet pr A " inlet pr A " inlet pr Dr. Gas Boom Tube Tips These Boom Tube Tips are similar to full-size Boom Tube, but are shorter in length for easy installation. They still have the same 8" by 1.75" compact size after the inlet transition. Tips are pre-cut at 45 degrees to expose an 11-1/4" opening at the side of the car and can be trimmed to match the profile of your car. Tips are fully MIG welded and are available individually or in pairs. Boom Tube tips are approximately 23" long on the long side and 14" long on the short side and are available with 2.5", 3" or 3.5" round inlet pipes. Made in USA. Note: Trimmed or modifi ed tips cannot be returned. Single Boom Tube Tips A " inlet LH exit ea A " inlet RH exit ea A " inlet LH exit ea A " inlet RH exit ea A " inlet LH exit ea A " inlet RH exit ea Boom Tube Tip Pairs A " inlet LH and RH pr A " inlet LH and RH pr A " inlet LH and RH pr F Flowmaster Super 10 Series Muffl ers Looking for the most aggressive sound available? Flowmaster s new Super 10 series mufflers are so aggressive, they aren t recommended for street driven vehicles. Best suited to racing applications, these feature the same Delta Flow performance technology used in the highly popular Super 40 and Super 44 series Flowmaster mufflers. Manufactured from durable 409S stainless steel for long life and offered in a variety of configurations. Backed by a limited lifetime manufacturer s warranty, these short, single chamber mufflers deliver the closest thing to open pipe sound possible. If you want high impact sound, the Super 10 series mufflers are the answer. Measures: 6.5" x 9.5" x 4". Note: These muffl ers are recommended for off-highway use, not for street driven vehicles F " center in/center out ea F "/2.25" center in/dual out ea F " offset in/offset out ea F " center in/center out ea F "/2.5" center in/dual out ea A A Dr. Gas Boom Tube Muffl ers Dr. Gas Boom Tube Mufflers offer the same fit as a Boom Tube, but have built-in mufflers! Perfect for low ground clearance applications while giving that great side exit look. Boom Tube mufflers are fully MIG welded and can be trimmed to match your vehicle s side profile. Untrimmed Boom Tube Mufflers are approximately 30" long and are available with 2.5", 3" or 3.5" round inlet tubes for both left and right side exit. Made in USA. Note: Test fi t before trimming. No returns accepted once Boom Tubes are trimmed or altered. Single Boom Tube Mufflers A " inlet LH exit ea A " inlet RH exit ea A " inlet LH exit ea A " inlet RH exit ea A " inlet LH exit ea A " inlet RH exit ea Boom Tube Muffler Pairs A " inlet LH and RH pr A " inlet LH and RH pr A " inlet LH and RH pr Dr. Gas Universal X-Pipe Crossover Dr. Gas designed and commercialized the X-pipe crossover in the 1980 s. X-pipes equalize exhaust system pressure imbalances while producing a scavenging effect for more power and efficiency. Exhaust note is dramatically improved to a smoother, higher pitch note. Universal X-pipe crossover sets are available in 2.5", 3", 3.5", and two special sizes with built-in reducers after the X junction. Sizes with reducers deliver enhanced torque without a horsepower loss. Complete sets include: two inlet bends, the X-pipe junction, two outlet bends, and flanges with gaskets and hardware. Precision made with premium materials. Made in USA. Note: Welding and trimming required. Test fi t before fi nal installation. No returns accepted once products are trimmed or altered Complete X-Pipe Crossover Sets A " inlet 2.5" outlet set A " inlet 3" outlet set A " inlet 2.5" outlet set A " inlet 3.5" outlet set A " inlet 3" outlet set X-Pipe Crossover Only A " inlet 2.5" outlet ea A " inlet 3" outlet ea A " inlet 2.5" outlet ea A " inlet 3.5" outlet ea A " inlet 3" outlet ea F F Flowmaster s Super HP-2 Muffl ers Designed for street rods, customs and vehicles where undercarriage space is tight, the Flowmaster Super HP-2 provides the exhaust performance you need in a compact package that fits wherever you need it. The Super HP-2 has a moderate tone with the appearance, durability, and sound control to suit daily drivers, weekend cruisers, and world-class show vehicles. Available with a 409S stainless steel case or polishable 304S stainless steel case in sizes from 2", 2-1/4" and 2-1/2". Made in USA 409S Stainless Steel Case F " 4"H x 5"W x 12"L ea F " 4"H x 5"W x 18"L ea F /4" 4"H x 5"W x 12"L ea F /4" 4"H x 5"W x 18"L ea F /2" 4"H x 5"W x 12"L ea F /2" 4"H x 5"W x 18"L ea 304S Polishable Stainless Steel Case F /4" 4"H x 5"W x 12"L ea F /4" 4"H x 5"W x 18"L ea F /2" 4"H x 5"W x 12"L ea F /2" 4"H x 5"W x 18"L ea Fuel & Exhaust L Mufflers 561

35 Mufflers Flowmaster 40 Series Muffl ers Flowmaster s original exhaust tone! This is the most aggressive sounding street/strip muffler that Flowmaster offers. If you re looking for attention, this one will get you noticed. The standard 40 series has an aggressive rumble and will generally resonate inside the vehicle around RPM, and again at RPM. Constructed of 16 gauge aluminized steel and fully mig-welded for maximum durability Offset Inlet/Center Outlet F " ea F " ea Offset Inlet/Offset Outlet F " ea F " ea Center Inlet/Dual Outlet F "/2.5" ea F42441 F F52556 Flowmaster Delta Flow 40 Muffl ers This two chamber design incorporates Flowmasters patented Delta Flow technology. The Delta deflectors result in increased scavenging for better performance and reduced interior resonance over the standard 40 series with a nice growl outside the vehicle. Sounds great on late model performance cars with catalytic converters. Constructed of 16 gauge steel and fully mig-welded for maximum durability. Center Inlet/Center Outlet F " ea Offset Inlet/Center Outlet F " ea F " ea Center Inlet/Offset Outlet F " ea Offset Inlet/Offset Outlet F " ea F " ea Flowmaster 50 Series Muffl ers The SUV/Performance muffler is a larger version of Flowmasters 50 Series Delta Flow muffler and is specially designed for trucks, light SUVs and high horsepower vehicles. The larger H-chamber reduces interior resonance to a minimum. Constructed of 16 gauge aluminized steel and fully mig-welded for maximum durability. Center Inlet/Center Outlet F " ea F " ea Offset Inlet/Center Outlet F " ea F " ea Center Inlet/Offset Outlet F " ea F " ea Offset Inlet/Offset Outlet F " ea F " ea F Fuel & Exhaust L F Flowmaster Super 40 Series Muffl ers The Super 40 gives you a deeper tone that retains our classic 40 Series sound and feel. Increased flow path radius for optimum internal flow using the latest in Delta Flow technology. Flowmaster state-of-the-art robot assembly technology assures a product that exceeds OEM auto manufacturers specifications. To achieve such critical quality, Flowmaster performs extensive R&D at the track and in-house with our own engine and chassis dyno facilities. Flowmaster Super 40 is aluminized, black in color and is the most aggressive, deepest sounding street two chamber muffler they ve ever built. Enjoy some American Thunder today! Center Inlet/Center Outlet F /4" ea F /2" ea F " ea Offset Inlet/Center Outlet F /4" ea F /2" ea F " ea Center Inlet/Offset Outlet F /4" ea F /2" ea F " ea Offset Inlet/Offset Outlet F /4" ea F /2" ea F " ea F F Flowmaster Super 44 Delta Flow Muffl ers The Super 44 is the most aggressive, deepest toned street and strip muffler Flowmaster has ever made! The Super 44 s offer maximum performance, an improved flow path radius, and generates more torque and more power than ever before! If you really want to hear your exhaust system inside as well as outside, the Super 44 is for you! Center Inlet/Center Outlet F /4" ea F /2" ea F " ea Offset Inlet/Center Outlet F /4" ea F /2" ea F " ea Center Inlet/Offset Outlet F /4" ea F /2" ea F " ea Offset Inlet/Offset Outlet F /4" ea F /2" ea F " ea Center Inlet/Dual Outlet F " ea F Flowmaster Delta Flow 50 Series This is the latest design of the 50 series muffler that utilizes Flowmasters patented Delta Flow technology along with an H-Chamber to eliminate most all interior resonance and still have that famous Flowmaster sound outside the vehicle. Constructed of 16 gauge steel and fully mig-welded for maximum durability. Center Inlet/Center Outlet F " ea Offset Inlet/Center Outlet F " ea F " ea F " ea Center Inlet/Offset Outlet F " ea Offset Inlet/Offset Outlet F " ea F " ea Flowmaster Muffl er Heat Shields Formed aluminum heat shield designed to mount on muffler for added protection in reducing heat radiated from mufflers and reducing interior noise. Attaches easily with included straps. Fits 5" x 10" x 17" mufflers. F ea 562 Mufflers Toll Free Order Line

36 Exhaust Systems Chambered Exhaust System For the last word in a correct show car quality restoration, we offer the final solution! We stock a complete chambered exhaust systems for your early model small block or big block Camaro. This reproduction will replace the long ago CE679SB discontinued, and highly sought after GM originals! Chambered exhausts were offered late in the 1969 model run and were optional on Z28, big block or COPO Camaro models. This free flow exhaust system will allow your engine to properly breathe with a minimum amount of back pressure and no performance loss! Though originally available only for special engine applications, this exhaust system can be installed on any V8 coupe Camaro, but will not fit convertible models! Unlike the originals, these exhaust systems are manufactured with an aluminized finish for longevity. Installation set available separately. Note: Shipped truck freight. CE678SB small block 2" headpipe, 2" intermediate and tail pipe set CE678BB big block 2-1/4" headpipe, 2" intermediate and tail pipe set CE679SB 1969 small block 2" headpipe, 2" intermediate and tail pipe set CE679BB 1969 big block 2-1/4" headpipe, 2" intermediate and tail pipe set CEH69BB small/big block hanger set includes 3 2" clamps, 2 2-1/4" clamps set Dual Exhaust Hanger Set Reproduction hanger set for Camaro models with dual exhaust. These are the original style hangers unlike the aftermarket replacements currently being offered. 4 piece set, zinc-plated. Note: Not for chambered exhaust. Clamps not included. K set 1969 Dual Exhaust Hanger Set Reproduction hanger set for 1969 Camaro models with dual exhaust. These are the original style hangers unlike the aftermarket replacements currently being offered. 4 piece set, zinc-plated. Note: Not for chambered exhaust. Clamps not included. K OE style set AE69SB Aluminized Exhaust System If you are seeking an original appearance with extended life in an exhaust system, then look no further! Classic Industries now offers this high-quality, aluminized exhaust system. Aluminizing of exhaust pipes means the pipes may outlast the rest of your car! This system uses the correct angle cut tips with factory styled flattened tail pipes and lead pipes and a original style transverse muffler. Available for both small block and big block applications. Not available for additional discounts. Important: Aluminized exhaust kits are for coupe models only. Note: Shipped truck freight. AE678SB small block 2" headpipe set AE678BB big block 2-1/4" headpipe set AE69SB small block 2" headpipe set AE69BB big block 2-1/4" headpipe set AE70SB small block 2" headpipe set AE70BB big block 2-1/4" headpipe set CE Aluminized Exhaust Installation Set This installation will enable even the shade tree mechanic the ability to install a complete aluminized exhaust system on Camaro coupes regardless of the engine size. This set includes all clamps and hangers necessary to install a full system. Note: Not for chambered exhaust. CEI installation set set CEI installation set set Chambered Exhaust Hanger Set Reproduction hangers for the chambered style exhaust system. These are correct for chambered only and not for standard aluminized or stainless steel exhaust sets. CEH69BB all (SB/BB) set SE69SB Stainless Steel Exhaust System When it comes to selection, Classic Industries can t be beat! These new stainless steel exhaust systems are not manufactured for the every day driver. This extremely high-quality reproduction is just what a perfect restoration needs. Get years of long lasting dependability with a stainless steel exhaust system. Available for both small block and big block applications. Note: Shipped truck freight. SE678SB small block 2" headpipe set SE678BB big block 2-1/4" headpipe set SE69SB small block 2" headpipe set SE69BB big block 2-1/4" headpipe set Exhaust Hangers Reproduction exhaust hangers for models all, LH ea all, RH ea Fuel & Exhaust L Exhaust Systems 563

37 Performance Exhaust P Pypes Header Back CrossFlow System Pypes has designed a 2-1/2" crossflow system for Camaro models needing maximum ground clearance. The Race Pro muffler is the first maximum flow, straight through, transverse mounted crossflow muffler system that doesn t need to sacrifice any performance or aggressive growl to give you clearance. This system also features a horsepower freeing X-pipe designed to fit into the driveshaft tunnel, which contributes to it s ability to glide over the nastiest speed bumps. Available in 409 stainless steel or 304 polished stainless, including X-pipe, muffler, intermediate pipes and tail pipes. Limited lifetime warranty. Important: Modifi cation to the body pan brace is required on convertible models. In order to utilize this X-pipe, it is necessary to either add a body pan designed to allow clearance for the X-pipe assembly, or remove the body pan and install subframe connectors. If using stock, cast iron manifolds, add a set of downpipes to connect your original manifolds to the header back system. OS2 Note: Shipped double oversize. P /2" 409 stainless steel 1/4 exit set P /2" 304 polished stainless 1/4 exit set Flowtech Performance Exhaust Systems From the makers of Holley performance products comes this great Super Street exhaust system. Get more power and sound out of your Chevy small block. Made from 2-1/4" 16 gauge, heavy-duty steel, this is a top quality, dual exhaust system that offers the maximum in versatility. All Flowtech Super Street dual kits are designed to locate all components above the frame and feature OEM exit locations. This kit comes with your choice of the Terminator muffler or the Raptor muffler. Kits come complete with installation hardware and instructions. Note: Shipped double oversize. OS with Terminator mufflers kit with Raptor mufflers kit BA Fuel & Exhaust L P1019S Pypes Crossmember Back Dual System Pypes has designed a crossmember back dual exhaust system for V8 models that incorporates a 16 gauge, mandrel bent stainless steel X-pipe to maximize exhaust gas flow and boost horsepower. This system features a Siamese designed X-pipe, a pair of Street Pro, Race Pro or Violator mufflers, tailpipes, cad plated clamps and hangers. The combination of the crossover and the mufflers deliver a perfect balance of sound and performance. Features 409 stainless steel X-pipe, mufflers, intermediate pipes and tail pipes. Limited lifetime warranty. Important: If using stock, cast iron manifolds, add a set of down pipes to connect your original manifolds to the header back system. Note: Shipped double oversize. With X-Pipe OS2 P1064A /2" pipes only without mufflers, side exit set P1064S /2" with Street Pro mufflers, side exit set P1064R /2" with Race Pro mufflers, side exit set P1064V /2" with Violator mufflers, side exit set P1019S /2" with Street Pro mufflers, rear exit set P1019R /2" with Race Pro mufflers, rear exit set P1019V /2" with Violator mufflers, rear exit set P1020S " with Street Pro mufflers, rear exit set P1020R " with Race Pro mufflers, rear exit set P1020V " with Violator mufflers, rear exit set True dual, without X-Pipe P1063S /2" with Street Pro mufflers, rear exit set P1063R /2" with Race Pro mufflers, rear exit set P1063V /2" with Violator mufflers, rear exit set Borla Cat Back Dual Exhaust Systems Get a deep, bold growl from your 3rd or 4th Gen with a Borla high flow cat-back exhaust system! Features 3" mandrel-bent tubing to reduce back pressure and improve performance. Includes: muffler, connection pipes, tail pipes, chrome exhaust tips, and mounting hardware. Manufactured from high-quality stainless steel and backed by a 1,000,000-mile warranty. Note: *Features 5 adjustable sound settings. AT/MT. Shipped oversize. With Chrome Dual Round 2-1/2" Angle-cut Exhaust Tips OS1 BA /5.7L ea With Chrome Square Intercooled Angle-cut Exhaust Tips BA14464 * L LT1 with single cat ea BA14555 * L LT1 with dual cat ea BA14780 * L LS ea With Chrome Single Round Angle-cut Exhaust Tips BA L LS ea 564 Performance Exhaust Toll Free Order Line

38 Performance Exhaust Crossmember Back Exhaust Magnaflow s Camaro systems start with mufflers specifically designed with internal paths that ensure fast, equalized exhaust flow so that both sides flow the same. The crossmember back systems are built with fast-flowing mandrel bent stainless steel tubing that feature Magnaflow s Tru-X crossover pipe. For V8 models only. Made in the USA. Note: Requires modifi cation for convertible. Shipped truck freight. Dual Exhaust ", transverse set " set " set Dual Exhaust Set This set extends from the catalytic converter (when applicable) to the tailpipes. This 12 piece set includes: two Super Turbo mufflers, two intermediate pipes, two tailpipes and 6 clamps. Note: Shipped double oversize. OS set Dual Pipe Cross Flow Exhaust American Thunder Series dual 2-1/2" system with H-pipe assembly and a transverse mounted 80 Series Cross Flow Delta Flow muffler. Features direct out rear stock exit tailpipes. Extends from transmission crossmember back. Not for convertibles. Note: Shipped double oversize. OS2 F V8 2.5" set Cat-Back Exhaust Systems Cat-back systems are built with fast-flowing mandrel bent stainless steel tubing. A Magnaflow wide-open performance muffler reduces engine heat and back pressure and improves exhaust scavenging from the combustion chamber for much stronger performance. For V8 models only. Made in the USA. Note: Shipped truck freight " dual rear exit set Performance Exhaust Systems Made from 2-1/4" 16 gauge, heavy-duty steel, this is a high-quality, dual exhaust system that will add horsepower to your Chevrolet small block. This kit comes with your choice of Ultra Flo SS muffler or Super Turbo muffler. Kit comes complete with all necessary hardware and instructions. Note: For 305 models only. Shipped double oversize. OS with Ultra Flo SS kit with Super Turbo kit F Flowmaster True Dual Exhaust American Thunder Series dual 2-1/2" system with H-pipe assembly and two Delta Flow mufflers. Direct out rear stock exit tailpipes. Extends from transmission crossmember back tailpipes feature stainless steel tips. Not for convertibles. Note: Shipped double oversize. With 44 Series Mufflers OS2 F V8 2.5" set F V8 2.5" set With 50 Series Mufflers F V set Cat-Back Exhuast Systems These systems are built with fast-flowing mandrel-bent stainless steel tubing and include long 3.5" diameter polished stainless steel tips. The Camaro V6 system is designed to look just like the V8 with split dual out tips. Magnaflow s wide-open performance mufflers outflow OEM chamber style mufflers by as much as 167%. This reduces engine heat and back pressure and improves exhaust scavenging from the combustion chamber. Made in the USA. Note: *Z28 and SS models only. Shipped truck freight. V6 Engine x 8 x 14" muffler set x 8 x 14" muffler set 5.7L V8 Engine x 8 x 18" muffler set x 8 x 18" muffler set * center quad outlet set * dual rear exit set F Single In/Dual Out Exhaust American Thunder Series exhaust systems feature aluminized pipes with stainless steel tips and an 80 Series Cross-Flow Delta Flow muffler. Available for models. Important: *With resonator. **Without stainless steel tip. Note: Shipped double oversize. OS2 2.5" In-Out F flanged cat ea F17357 * slip-fit cat ea F17133 ** dual cat ea 3.8 slip-fit cat ea F17358 * " In 2.5" Out F17143** " cat ea 3" In-Out F V8 3" cat ea F V8 2.5" cat ea F " cat ea F ea F15937 U-Fit Dual Pipe Sets These sets come complete with all the pipes you need to build a custom dual exhaust system in 2-1/4", 2-1/2" or 3" pipe diameters. These U-Fit sets include: the front adapter pipes, intermediate pipes, H-pipe assembly and over-the-axle pipes. Each piece has a slip-fit connection, for easy assembly and built from mandrel bent, 16 gauge aluminized steel tubing. Important: Hardware not included. OS2 Note: Shipped double oversize. F /4" set F /2" set F " set Fuel & Exhaust L Performance Exhaust 565

39 Exhaust Cutouts MN2443 MN2446 MN2447 MN2460 MN2450 MN2457 MN2453 Electric Exhaust Cutouts Don t crawl under your car to uncork your exhaust ever again by switching to electric cutouts. Keep them closed and quiet for the street, wide open for the strip, or anywhere in between with the flip of a switch. You control the volume and the power! Available in sizes 2-1/4" to 4" and a low profile oval design for applications with limited ground clearance. Fits 2-1/4" to 3" round exhaust pipe. Built with high-quality materials CNC 6061 aluminum body and motor plate, stainless steel shaft and butterfly plate, high torque DC gear driven motor, weather tight wiring connectors, and custom illuminated toggle switch. Note: Match valve size with cutout size for optimal fi t and performance. Electric Cutout Valves Individual Part# Cutout Size Additional Notes Price MN /4" valve ea MN /2" valve ea MN2445 3" valve ea MN2446 oval valve includes connector, fits 2-1/2" to 3" round pipe ea MN /2" valve ea MN2448 4" valve ea MN2449 4" valve includes 4" three-bolt flange ea Electric Cutout Valve Sets MN2450 two 2-1/4" valves pr MN2451 two 2-1/2" valves pr MN2452 two 3" valves pr MN2453 two oval valves includes connector, fits 2-1/2" to 3" round pipe pr MN2454 two 3-1/2" valves pr MN2455 two 4" valves pr MN2456 two 4" valves includes 4" three bolt flange pr MN2459 Universal Exhaust Turn Downs Universal exhaust turn downs for electric cutouts. The round tips feature a 360 degree floating flange which allows turning in any direction. Manufactured from stainless steel with a polished finish. MN /2" turn down ea MN2458 3" turn down ea MN2459 oval turn down ea Pypes Electric Cutouts The optional electric exhaust cutouts and make uncorking your exhaust as easy as flipping a switch. Electric cutout set includes: 2 valves, wire harness, switch, mounting hardware and 2 gaskets. Limited lifetime warranty. Electric exhaust cutouts fit 2-1/2" or 3" dump legs. P1074 3" electric exhaust cutout set set Doug's Stainless Steel Electric Cutouts These cutouts feature a rugged 12 volt DC motor and rotating gate for a leakproof seal every time the cutout is opened and closed. When fully opened, these cutouts do not create exhaust flow obstructions that can create a leaky gasket sound, unlike butterfly style cutouts. A pre-wired harness with an illuminated rocker switch is supplied for easy installation. Uncork your exhaust with the flip of a switch from your dash. The cutouts are ideal for race tracks that don t require mufflers. Cutouts are available individually, in pairs, or in complete kits with Y-Pipes for easy installation. Made in the USA. Note: May not be legal for highway use or use on emission controlled vehicles. Important: Not recommended for vehicles equipped with catalytic converters. Single Cutouts and Pairs /2" single electric cutout ea /2" pair electric cutouts pr " single electric cutout ea " pair electric cutouts pr Buy the Complete Set and Save! /2" set " set MN2461 Fuel & Exhaust L Stainless Steel Cutout Pipes Stainless steel exhaust cutout pipes for all models. Manufactured from 304 stainless steel with a polished finish. They feature a TIG-welded construction with a 3/8" flange for a proper seal. Includes: the end cap, gasket and hardware for an easy installation. MN /4" cutout ea MN /2" cutout ea MN2462 3" cutout ea MN /2" cutout ea MN2464 4" cutout ea Electric Cutout Remote Control System Remote control for your electric cutout system. When space is a premium this control box gives you the flexibility you need. Includes 2 wireless key fobs for 100% control over your cutouts at the push of a button. MN set Doug's Stainless Steel Cutout Turn Downs Easily route your cutout exhaust flow away from the floor boards or in any direction with these easilyinstalled 304 stainless steel turn downs. These turn downs are made specifically for Doug s electric cutouts and included stainless band clamps for weld free attachment. Made in the USA /2" turn down pipe ea " turn down pipe ea 566 Exhaust Cutouts Toll Free Order Line

40 INC. Exhaust Tips A P1048 F15361 F15364 P1049 B C F15362 Flowmaster Stainless Rolled Edge Tip Stainless exhaust tip that is designed with your choice of a rolled edge or angle cut tip. Finished with an embossed Flowmaster logo. Sold individually. Clamp-on Rolled Edge Tip F " dia. for 2.5" pipe-12" L ea F " dia. for 3" pipe - 12"L ea Clamp-on Double Wall Rolled Edge Tip F " tip fits 2.25" pipe ea F " tip fits 2.5" pipe ea Weld-on AngleCut Tip F " dia. for 2.5" pipe-13" L ea Stainless Steel Exhaust Tips Made of T-304 stainless steel this tips will stand out on any vehicle. Made in the USA. Dual Rectangular Tips " x 8" dia., 11" long, 2.25" i.d pr Turndown Tips MF " dia., 13" long, 2.75" i.d ea MF " dia., 13" long, 3" i.d ea 15 Degree Slash Cut Tips " dia., 12" long, 3" o.d ea " dia., 18" long, 2.5" i.d ea " dia., 22" long, 2.5" i.d ea " dia., 12" long, 3" i.d ea " dia., 18" long, 2.5" i.d ea " dia., 22" long, 2.5" i.d ea " dia., 12" long, 3" i.d ea " dia., 18" long, 2.5" i.d ea " dia., 22" long, 2.5" i.d ea 45 Degree Slash Cut Tips " dia., 18" long, 2.25" i.d ea " dia., 18" long, 2.5" i.d ea " dia., 22" long, 2.25" i.d ea " dia., 22" long, 2.5" i.d ea " dia., 18" long, 2.25" i.d ea " dia., 18" long, 2.5" i.d ea " dia., 22" long, 2.5" i.d ea " dia., 18" long, 2.5" i.d ea " dia., 22" long, 2.5" i.d ea Pypes Stainless Exhaust Tips These tips add the final personal touch to your custom exhaust! The extensive line of stainless steel Pypes exhaust tips will provide years of eye-popping looks and excellent durability. For 2.5" Pipes P1048 dual 3.5" splitters pr P1049 6" x 3" oval tip pr P1050 8" x 2" rectangle tip pr 9" slash cut tip pr P1051 P " rolled edge tip pr P1053 4" x 2" oval tip pr P " long slash cut tip pr For 3" Pipes P1080 dual 3.5" splitters pr P1081 6" x 3" oval tip pr P1082 8" x 2" rectangle tip pr 9" slash cut tip pr P1083 P " rolled edge tip pr P1085 4" x 2" oval tip pr P1073 3" long slash cut tip pr ST778C P1050 P1051 P1052 P1053 Bow Tie Exhaust Tips 8" length fits 2-1/4" pipe. Universal fit. 1/8" thick carbon steel (or 1/16" T-304 stainless steel). Choose from 2 popular finishes triple chrome-plated or stainless steel. Made in the USA. ST778C chrome-plated, 8" ea ST778S stainless steel, 8" ea We ve Got A Hot Tip For You! Top off your exhaust system with a handsome T-6 Billet aluminum exhaust tip. Steel slip-on mount is included to provide for easy clamp-on or weld-on installation. Available in your choice of brushed or polished finish. Exhaust clamps are sold separately. A Ball Milled Polished 2002P 2-1/2" square fits 2" ea 2001P 3" square fits 2-1/4" ea 2000P 3" square fits 2-1/2" ea Brushed Finish 2002B 2-1/2" square fits 2" ea 2001B 3" square fits 2-1/4" ea 2000B 3" square fits 2-1/2" ea B Powered By Chevrolet (Bow Tie) Polished 9002P 2-1/2" square fits 2" ea 9001P 3" square fits 2-1/4" ea Brushed Finish 9002B 2-1/2" square fits 2" ea 9001B 3" square fits 2-1/4" ea 9000B 3" square fits 2-1/2" ea C Flamed Polished 4002P 2-1/2" square fits 2" ea 4001P 3" square fits 2-1/4" ea 4000P 3" square fits 2-1/2" ea Brushed Finish 4002B 2-1/2" square fits 2" ea 4001B 3" square fits 2-1/4" ea 4000B 3" square fits 2-1/2" ea C2505 C2506 Chevrolet Exhaust Defl ectors Add vintage style to your Chevrolet and protect your paint at the same time with these stainless steel exhaust deflectors. Exhaust deflectors clamp on the tailpipe to deflect the exhaust downward, preventing the exhaust from discoloring your chrome or paint. C2505 Bow Tie logo with Chevrolet ea C2506 Bow Tie logo only ea Fuel & Exhaust L Exhaust Tips 567

41 Exhaust Components Exhaust Repair Kit Complete kit for repairing cracks and splits in mufflers tailpipes and exhaust pipes. Withstands temperatures over 1000 degrees F. The kit contains ready-to-use foil packed bandage and support wire. S ea Muffl er And Tailpipe Repair Putty and sealer seals holes and leaks in mufflers, tailpipes and around joints. Makes new installation more secure. Resists temperatures up to 2000 degrees F. Epoxy impregnated fiberglass bandage chemically welds mufflers and tailpipes. Great for mufflers, tailpipes, joints and catalytic convertors. S80335 sealer 3 oz. tube ea S80333 putty 4 oz. pouches ea S80331 bandage 84 sq. in ea Cool It Plug Wire Sleeves This unique spark plug and ignition wire protector comes in four colors: red, blue, black and silver. These dual purpose sleeves enhance performance, reduce misfires, extend plug wire life and will not react with petroleum products. The double wall construction keeps the wire and boot cooler in a high temperature engine. Its universal size fits most boots, is easy to install and most importantly is nonflammable. Cool It Plug Wire Sleeves can be used in any temperature environment from street vehicles to race cars. Sold in packs of 6 TT14262 black set TT14261 red set TT14263 blue set TT14260 silver set This Flexible Heat Shield Clips Into Place! The Header Manifold Blanket provides excellent heat-retention for exhaust headers and manifolds. This flexible heat shield simply clips into place on the upper portion of the header. The fabric side of the material should be facing the heat source, and the aluminized side facing away offering protection from abrasion and harmful liquid spills. The Header Manifold Blanket is available in two sizes: two 20" by 24" blankets for V6 and V8 applications, and one 36" by 40" blanket for straight 6 and 4 cylinder engines. TT1017 V6-V8 applications pr TT1018 straight 6 or 4 cylinder models ea Fuel & Exhaust L Socket Assist Essential tool for bolts with tight clearance like spark plugs and header bolts! 12 point for maximum finger traction. Set of three including: 1/4" x 1/4", 1/4" x 3/8", 3/8" x 3/8" (12 point x socket drive size). These belong in every tool box piece set set Dual Drive Oxygen Sensor Wrench Tool comes with both 1/2" and 3/8" drive. Attach a 1/2" breaker bar on the end of the tool to initially loosen stuck sensors. Use a 3/8" ratchet on the top for fast removal and installation. Fits oxygen sensor applications with a heat shield. Slotted body allows clearance for wire harness. Forged, heat treated steel with six point design will withstand high torque removal applications ea SS High Temperature Stainless Steel Cable Tie High temperature stainless steel cable ties are great for harsh environments. Perfect for installing heavyduty and high temp sleeving. Available in 7-1/2" or 14-1/2" lengths. Individual SS /2" ea SS /2" ea 5 Pack SS /2" kit SS /2" kit 10 Pack SS /2" kit SS " kit Reduce Underhood Temperatures! Increased exhaust scavenging is produced, along with lower intake temperatures. Exhaust Insulating Wrap withstands continuous heat up to 2000 degrees F, and contains no asbestos. Will not over insulate a system when properly installed due to a proprietary coating developed by Thermo-Tec Thermal Conduction Technology (TCT) that conducts heat across the wrap s surface. The 1/16" thick wrap is available in 1 inch or 2 inch widths in 15' or 50' rolls. Choose from off-white or graphite black. Off-White Exhaust Wrap TT1009 1" x 15' short roll ea TT1011 2" x 15' short roll ea TT1010 1" x 50' long roll ea TT1012 2" x 50' long roll ea Graphite Black Exhaust Wrap TT1053 1" x 15' short roll ea TT1054 2" x 15' short roll ea TT1013 1" x 50' long roll, black ea TT1014 2" x 50' long roll, black ea Reduce Underhood Temps Up to 70%! The new quick wrap, high velocity Exhaust Jackets are an innovative way to insulate and block radiant heat. The jackets cover the header tubes vertically allowing for a consistent fit. The fit allows the exhaust system to expand as it comes up to operating temperatures without restrictions and provides air space for added insulation. This product uses Thermal Conduction Technology (TCT), developed by Thermo-Tec, and can be applied with the headers in the vehicle. TT cylinder ea TT cylinder ea Generation II Copper Header Wrap Generation II Copper Header Wrap improves heat resistance up to 30% more than current technology, by utilizing a new proprietary coating developed by Thermo-Tec; improved Thermal-Conduction- Technology (T-C-T). Generation II Copper Exhaust Wrap creates more horsepower and reduces underhood temperatures, increases exhaust scavenging, withstands continuous heat up to 2000 degrees F, contains no asbestos. TT " x 50' ea TT " x 50' ea natural black Vermiculite Coated Header Wrap Insultherm Header Wrap is an extremely high temperature resistant wrap used to insulate hot gases in automotive exhausts. Manufactured from texturized fiberglass yarns that are woven into a strong, flexible wrap with vermiculite coating. Resists gasoline and engine chemicals and withstands temperatures up to 1200 degrees F (maximum continuous temperature of 1000 degrees F). Available in black or natural in 50' or 25' rolls. 1" Header Wrap HW black 1" x 50' ea HW natural 1" x 50' ea HW black 1" x 25' ea HW natural 1" x 25' ea 2" Header Wrap HW black 2" x 50' ea HW natural 2" x 50' ea HW black 2" x 25' ea HW natural 2" x 25' ea 568 Exhaust Components Toll Free Order Line

42 Exhaust Components TT15002 TT12001 TT12002 TT12003 Hi-Heat Coating To finish off a clean and well protected Exhaust Insulating Wrap application it is recommended to use the Hi-Heat Coating. The coating will protect the wrap from abrasion and harmful liquid spills. Extra resins and binders toughen the surface, extend the life of wrap by protecting it from friction, and seal the pores to minimize the penetration of harmful liquids. The coating also works excellent as a paint directly on metal surfaces. 11 oz. TT12001 black ea TT12002 aluminum ea TT12003 copper ea Starter Heat Shield Set In today s high heat environment, starters take in a lot of damaging heat that destroys the windings of the starter and solenoid. To combat this problem, we offer a non-conductive strap-on heat shield with a highly reflective mylar surface. The Starter Heat Shield will reflect over 90% of radiant heat, adding life to the starter and assuring reliable starts. The Starter Heat Shield is a universal set that fits all starters. TT1002 with straps set Shield Plastic Or Rubber Hoses And Wiring From Radiant Heat! Thermo-Shield protects hoses and wires from radiant heat. Unprotected, rubber hoses and plastic or rubber insulated wiring can dry out, melt or crack over time. Thermo-Shield is used in applications where it is difficult or not practical to disconnect one end of the hose or wire. The adhesive-backed composite construction tape can easily be wrapped around the hose or wire to make a clean, professional appearance. Reflects radiant heat up to 2000 degrees F. Provides a barrier against the extreme conditions that underhood components are exposed to. Wrap your fuel lines and say good-bye to vapor lock. TT /2" x 15' feet ea TT1051 2" x 50' feet ea Battery Heat Shield Excessive heat in the engine compartment will cause most standard batteries to spew or seep corrosive battery acid. Prolong battery life with the world s only acid neutralizing heat barrier mat. It reflects over 90% of radiant heat, traps and neutralizes battery acid, protects against corrosion, is recyclable, protects the environment, and is inexpensive and easy to install. The Battery Heat Barrier set is completely safe to handle before and during installation. It is so effective, it is used by all branches of the U.S. Military. Set consists of one 8" x 40" acid absorbing/neutralizing felt and one adhesive backed 8" x 40" aluminized thermal barrier to wrap around the battery, plus an 8" x 12" acid absorbing/neutralizing pad to put beneath the battery. Install one on your vehicle NOW, before it s too late. TT1001 battery heat shield set set Keep Cool! Refl ect Radiant Heat Away From Your Passenger Compartment! The Muffler/Catalytic Converter Heat Shield is made up of woven silica with a flexible mylar finish. The highly reflective heat shield can be installed between the catalytic converter, muffler, or any other component to reflect radiant heat away from the undercarriage of the car. The kit includes one 24" x 40" mylar heat shield and all necessary fasteners. TT1007 muffler heat shield ea TT11600 Clamp-On Heat Shield The flexible Clamp-On Heat Shield blocks more than 90% of damaging radiant heat from the exhaust. The high tech composite construction provides the ultimate in protection by incorporating Thermo-Conductive- Technology, a highly texturized silica-based fabric. Clamp-On Shields are available in 1', 2' and 3' lengths. Sets come complete with all clamps and install easily in minutes. TT " x 1 foot set TT " x 2 foot set TT " x 1 foot set TT " x 2 foot set TT " x 3 foot set Turbo Insulating Set The Turbo Insulating Set is designed to protect and improve performance of the turbo. This universal set will help reduce turbo lag. The cut-to-fit set comes with a substantial amount of material to cover turbos from the smallest automotive application to heavy-duty truck applications. TT or 8 cylinder set set TT15003 turbo insulation cover only ea TT13101 Snap Strap Quality stainless steel straps with a dependable multilock system are available in standard lengths. The narrow width, standard length straps come with the multi-lock already attached just insert the end and pull to tighten. Standard Lengths TT13105 (6) 9" straps, (4) 18" straps set TT13101 (8) 9" straps, (4) 18" straps set Individual Lengths TT pack of 9" straps set TT pack of 18" straps set TT1020 Thermo-Sleeve Thermo-Sleeve is the combination of a high temperature fabric laminated to a highly reflective Mylar foil. It provides protection from radiant heat for hoses and wires. Thermo-Sleeve s ultra lightweight construction provides more insulation than traditional bulky rubber-coated fiberglass. The aluminized sleeve reflects more than 90% of radiant heat, plus it is fireproof and oil resistant! Thermo-Sleeve is available in 3' or 12' lengths. 3' Foot Lengths TT1020 1/4" to 1/2" inside dia ea TT1021 5/8" to 1" inside dia ea TT /8" to 1-1/2" inside dia ea TT /8" to 2" inside dia ea TT /8" to 2-1/2" inside dia ea 12' Foot Lengths TT1026 1/4" to 1/2" inside dia ea TT1027 5/8" to 1" inside dia ea TT /8" to 1-1/2" inside dia ea TT /8" to 2" inside dia ea 2-1/8" to 2-1/2" inside dia ea TT1030 Fuel & Exhaust L Exhaust Components 569