Part A. A1 Introduction. AP-550 Installation Manual. Installation manual. for the universal. AP-550 GoldCruise
|
|
- Brent Harmon
- 6 years ago
- Views:
Transcription
1 AP-550 Installation Manual Installation manual for the universal AP-550 GoldCruise Part A A1 Introduction The GoldCruise is an optimal flexibility product which consists of a universal part and a specific part. The universal part consists of: - ECU - actuator - wiring harness - Installation Manual Part A The specific part consists of: - actuator cable - actuator assembly kit - cable linkage materials - Installation Manual Part B The AP550 GoldCruise is a quality product, which was developed for Gold Automotive with high precision. The actuator pulls the accelerator pedal or throttle valve by means of a steel cable to maintain a set speed. The ECU receives and processes signals from the command module, brake pedal and Vehicle Speed Sensor (VSS). With this information the ECU directs the actuator. This is a so called Closed Loop process. The installer of the GoldCruise has to be familiar with the technique of modern cars and experienced with working on these automobiles. To ensure a problem-free installation, please read this installation manual carefully before getting started. After completing the installation of the GoldCruise always leave the sheet at the back of this manual with command functions behind in the car for the user.
2 A2 Safety first Symbol explanation: Beware! Following terminal designations are used in vehicle wiring: Beware! This symbol indicates a (possible) hazardous situation The hazardous situation may cause (serious) injuries or death, damage to the car, damage to the product itself or harm the environment. This symbol indicates a strong and important advice to the installer. Neglecting this advice may cause damage to the engine or the GoldCruise-system itself. +30" input of battery plus, direct - 31" recirculation from battery mass, ground +15" switched plus, behind battery - Never change, manipulate or open any part of the GoldCruise. This can effect the functioning of the GoldCruise seriously, and will cause the warranty to become void. - Installation of the GoldCruise by an unqualified person can cause serious injuries and/or damage to the car, the product or the environment. - To avoid damage to the GoldCruise, use a multimeter or a LED-tester if necessary. Beware! - Always disconnect the negative terminal of the battery before working on the electrical equipment of the vehicle. The disconnection of the negative terminal may cause loss of volatile memories of the comfort-electronics. - To secure the connection between two electrical wires, Gold Automotive advices to solder and then insulate the connection. Gold Automotive B.V. does 1) incorrect assembly of the GoldCruise parts not accept any liability for 2) damage to the GoldCruise-system by mechanical damages due to the following: effects and overvoltages 3) use for any purpose, not described in this manual 4) changes, modifications and manipulations of the GoldCruise without the explicit approval of Gold Automotive B.V.
3 A3 Electronic Control Unit Mount the ECU under the dashboard, away from extreme heat and moisture. Secure the ECU with ty-strings, doublesided tape or screws. Warning! Never mount the ECU in the engine bay, where heatsources, vibrations and moisture exist A4 Command Modules The AP-550 GoldCruise can be supplied with one of these three different Command Modules: CM-25; The ultimate Command Module with OE-like design and the unique 3-Memory Cruise functions. CM-GK; Cruising and changing gear in one. CM-IR; Infrared module, fitted directly on the steering wheel. CM-8; 3-Memory Cruise module Extra module combined with CM- GK or CM-IR for extra comfort in cruising Please refer to the installation manual supplied with the command module for mounting instructions Programming 3-Memory in CM-25 and CM-8: The 3-Memory can be programmed in two simple steps: 1.) drive desired speed 2.) press button 1,2 or 3 until beep is audible
4 A5 Self Learning Procedure Self Learning Procedure for VSS, sensitivity and Reaction time: VSS = Vehicle Speed Sensor (number of pulses per kilometer) Sensitivity = when during cruising the adjustments of the GoldCruise are too forceful or too slow. Reaction Time = time span between activation (pressing the "Fix"-button) and the actual taking over of the GoldCruise. If this parameter is not correct, the result will be an overshoot or significant drop in vehicle speed. The AP-550 GoldCruise requires a setup for the speed pulse, in this procedure sensitivity and reaction time are also adjusted. This setup will usually result in satisfying settings. Activation of the Self Learning Procedure for VSS, Sensitivity and Reaction time confirmation: steps: (process steps 1-4 within one minute) 1 Turn the vehicle ignition switch OFF and then ON again. 4 beeps 2 Apply the brakes, and (slowly) press Fix/KM+ 4 times. 1 beep 3 Still applying the brakes, press Mem/KM- once. 1 beep 4 Release the brake pedal 5 Drive the car at a speed of approximately 70 km/h and press Fix/KM+. The GoldCruise takes over. 2 beeps 6 Drive for one kilometer and then apply the brakes. 7 Stop the vehicle in a safe spot and turn the ignition off. Make a test drive to check the GoldCruise operation. Attention! FIX/KM+ = SET/ACC = MEM/KM- = RES/DEC = Test drive: a) Drive the car in highest gear at about 90 km/h b) Press Fix/KM+ and let go of the accelerator pedal The GoldCruise should take over now. c) Briefly apply the brakes The GoldCruise should let go now. d) Drive the car at about 75 km/h, now press Mem/KM- and let go of the accelerator pedal The GoldCruise should resume to the previously set speed e) While cruising press Fix/KM+ and hold it, the car should accelerate. Let go when the car has accelerated about 10 km/h f) Still cruising press Mem/KM- and hold it until the car has decelerated about 5 km/h If the result of the "Self Learning Procedure" is not satisfying, the "Sensitivity" and "Reaction time" can be adjusted.
5 A5 Self Learning Procedure Adjusting Sensitivity and Reaction time Sensitivity: confirmation: steps: (process steps 1-4 within one minute) 1 Turn the vehicle ignition switch OFF and then ON again. 4 beeps 2 Apply the brakes and press Fix/KM+ 4 times. 4 beeps 3 Still applying the brake, press Mem/KM- 4 times. 4 beeps 4 Release the brakes. 5 Drive the car at the speed where sensitivity adjustments are required and press Fix/KM+. The GoldCruise will take over immediately. If the GoldCruise gains or looses speed while cruising, you can make adjustments to the sensitivity settings of the GoldCruise. 1 beep per step 6 By pressing Fix/KM+, the sensitivity will increase by one step. Pressing Mem/KM-, the sensitivity will be decreased by one step. The settings are changed straight away. 2 beeps 7 After changing the sensitivity, apply the brake, the new settings are saved. 8 When the result is satisfying, stop the vehicle in a safe spot and turn the ignition OFF. Make a test drive to check the GoldCruise operation. Reaction time: confirmation: steps: (process steps 1-4 within one minute) 1 Turn the vehicle ignition switch OFF and then ON again. 4 beeps 2 Apply the brakes and press Fix/KM+ 4 times. 3 beeps 3 Still applying the brake, press Mem/KM- 4 times. 3 beeps 4 Release the brakes. 5 Drive the car at a speed of approximately 70 km/h and press Fix/KM+. The GoldCruise takes over. If the Goldcruise takes over too slow or too fast (overshoot) you can make adjustments to the reaction time settings. 1 beep per step 6 By pressing Fix/KM+, the reaction time will increase (more agressive) by one step. Pressing Mem/KM-, the reaction time decrease (less agressive) by one step. The settings are changed straight away. 2 beeps 7 After changing the reaction time, apply the brake, the new settings are saved. 8 When the result is satisfying, stop the vehicle in a safe spot and turn the ignition OFF. Make a test drive to check the GoldCruise operation.
6 A6 Diagnostic Mode Activating the diagnostic mode Attention! FIX/KM+ = SET/ACC = MEM/KM- = RES/DEC = 1 Turn the ignition OFF 2 Press the Fix/Km+ -button and do not release 3 Turn the ignition ON again 4 Wait until the ECU is responding with a beep. 5 Release the Fix/Km+ -button 6 Turn the GoldCruise ON and the LED on the Command Module will glow green. - The diagnostic mode is activated; start test 1 Test 1 Testing actuator, command module and brake light connection Test 2 Testing speed pulse signal Press the Fix/km+ button, a beep is audible. The LED will turn red. The AP-550 actuator will slowly pull the cable in steps go to table 1 Activate the diagnostic mode as described above, but on step 3 start the engine Press the Mem/km- button, a beep is audible. The AP-550 actuator will slowly release the cable in steps go to table 1 Press the Fix/km+ button, until the engine revs. Let go of the button, now the engine revs should become constant go to table 2 Apply the brakes, a beep is audible. The LED will turn green again. The actuator will completely release the cable at once go to table 3 Drive at least 30 km/h, the LED on the ECU will flash and a beep is audible simultaneously go to table 4 operates well go to Test 2 To turn OFF diagnostic mode Switch OFF the ignition. For Frequent Asked Questions refer to back page
7 A6 Diagnostic Mode Table 1. Check whether the LED on the ECU glows on pressing the Fix/KM+ button. Also check this for the Mem/KM- button Check the connection for the orange wire on an ignition feed (+15) Check the 4-pin connector for solid colour to colour connections go to table 2 Check the 8-pin connector for solid colour to colour connections Check that the Command Module is switched ON Check the feed, fuse and ground connection Check that the LED on the ECU glows when applying the brakes Does not Does operate operate. go Command to table 3 Module faulty Check if the brown wires are both connected to the brakelight switch Check if one wire has 12V and the other has ground through the brakelights. (brakepedal released) If correct: ECU faulty Table 3. If incorrect: Check brakelight fuse, brakelights and connection of brown wires Table 2. Switch the engine and ignition OFF! Undo the 4-pin connector Connect one of the black wires to 12V and the other to a ground. A click should be audible when connecting. Leave these wires connected! Connect the lightblue wire to 12V and the blue/red wire to ground. The actuator pulls the cable. Check that the actuator cable has slotted correctly in the pulley. If so, the actuator is faulty. Doesn t operate: actuator faulty Table 4. Check the connection of the blue wire and whether it is connected to a speed pulse signal Redo the Self Learning Procedure
8 A7 Frequently Asked Questions The "Self Learning Procedure - Execute the Diagnostic mode. is not functioning - Check if the blue wire is connected to a real VSS. - All commands should be confirmed by a "beep" of the ECU. The GoldCruise does not - Make sure the fuse is placed in the fuse holder. operate at all - Check if all the terminals are positioned correctly in the connector (Actuator and Command Module). The GoldCruise is very - The travel of the throttle construction is too short. unstable while cruising - The cruise cable has too many curves - The cruise cable pulls from an angle - The outer cable mounting has too much flex - If all the above do not apply adjust the "sensitivity" It is impossible to activate the - The orange wire is connected to a permanent feed (+30) "Self Learning Procedure" or instead of a ignition switched feed (+15) Diagnostic mode In the Self Learning Procedure - Finish the Self Learning Procedure by applying the brakes the GoldCruise is operating, - After starting again first set the GoldCruise on stand-by with but after turning off the the ON/OFF-button ignition the cruise doesn t operate anymore The GoldCruise reacts slow or - The travel of the throttle construction is too long can not maintain the speed - The cruise cable has too many curves - If the above do not apply adjust the "reaction time" and/or the "sensitivity" The GoldCruise shuts off - The orange wire is not connected to a direct ignition feed when another user is switched - The ground connection (green wire) is faulty on - Interference with VSS, connect the blue/black wire to an other wire The GoldCruise doesn't - Redo the "Self Learning Procedure" at a higher speed. operate over a certain speed - The travel of the throttle construction is too long, so the cruise can not reach full throttle The GoldCruise doesn't - Redo the "Self Learning Procedure" at a lower speed. operate below a certain speed
9 User Guide Always hand this page to the user Command Functions: To turn GoldCruise ON: Press Press ON OFF Press To activate GoldCruise: counterclockwise Press SET ACC Press FIX KM+ To increase speed: stepwise by 1 km/h per step continuously counterclockwise counterclockwise and hold Press SET ACC Press SET ACC and hold Press FIX KM+ Press FIX KM+ and hold To decrease speed: stepwise by 1 km/h per step clockwise Press RES DEC Press MEM KM- continuously clockwise and hold Press RES DEC and hold Press MEM KMand hold To disable GoldCruise Press Press ON OFF Press remains stand-by using or or COAST Memory function: Last set speed clockwise Press RES DEC Press MEM KM- 3 preset Memory buttons The 3-Memory can be programmed in two simple steps: 1.) drive desired speed 2.) press button 1,2 or 3 until beep is audible Press one of these buttons to activate the GoldCruise on a preset speed.
10 User Guide Always hand this page to the user Safety features: The GoldCruise is equipped - When depressing the brake pedal with numerous safety - When depressing the clutch pedal (if connected) features, that will disengage - When pressing the OFF-button of the Command Module the GoldCruise in the - Decelerating to 50% of the set cruise-speed following situations: - Accelerating to 150% of the set cruise-speed - When turning the ignition OFF - The brake fuse blows - The brake lights burn out - Any connection of the GoldCruise becomes disconnected To ensure a safe operation always think of this: The Goldcruise will automatically switch OFF after the ignition has been switched OFF. Gold Automotive B.V. recommends that the Goldcruise remains switched OFF when not in use. Never activate the GoldCruise when the gearbox is in neutral or when the clutch pedal is depressed! Never use the GoldCruise in heavy traffic or during bad weather Beware! It is always possible to accelerate by foot while cruising. Letting go of the accelerator pedal will cause the speed to return to the previously set speed. In case a drastical speed reduction is required, apply the brake pedal. Never forget, the cruise control does not apply the brakes! Beware! - The memory function can only be activated if the actual speed is higher than 30 km/h - The ignition has not been switched OFF in the meantime
INSTALLATION MANUAL AP60B INSTALLATION MANUAL
INSTALLATION MANUAL 2. TOOLS REQUIRED The following is a list of tools required to properly install the cruise control. While this unit may be installed without some of the tools listed, it is recommended
More informationCRUISE CONTROL SPEED LIMITER Rev. 4.0
INSTALLATION f MANUAL CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series 231.0004530 Rev. 4.0 1 2 CONTENTS: Chapters 1 Kit contents. 3 2 Tools required 4 3 Electronics module location... 5 4 Input
More informationPage No General Installation Wiring diagram AP Wiring diagram AP Tools required...5. Parts list AP Parts list AP250...
INSTALLATION SECTION Page No General Installation Wiring diagram AP150...3 Wiring diagram AP250...4 Tools required...5 Parts list AP150...6 Parts list AP250...8 Installation instruction Vacuum actuator
More informationCRUISE CONTROL SPEED LIMITER. SL900Series. Dealer address details: Rev. 3.0
USER GUIDE f CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series Dealer address details: 11 231.0005010 Rev. 3.0 1 2 CONTENTS: 1 Product variants... 2 2 Cruise Control Safety Features. 3 3 Operating
More informationCRUISE CONTROL SPEED LIMITER. SL900Series. Dealer address details: C Rev. 7.0
INSTALLATION f MANUAL CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series Dealer address details: 35 231.000453C Rev. 7.0 1 2 NOTES: CONTENTS: Chapters 1 Kit contents. 3 2 Tools required 4 3 Electronics
More informationCruise Control designed. The only. and developed in Australia CRUISE CONTROL OPERATING INSTRUCTIONS. PROFESSIONAL SERIES and DRIVE by WIRE
The only Cruise Control designed and developed in Australia CRUISE CONTROL OPERATING INSTRUCTIONS PROFESSIONAL SERIES and DRIVE by WIRE CONGRATULATIONS! You have purchased one of the most advanced cruise
More information1999 Toyota RAV ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4
1999 ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4 DESCRIPTION WARNING: Deactivate air bag system before performing any service operation. See AIR BAG RESTRAINT SYSTEMS article. DO NOT apply electrical
More informationAP500 FAULT FINDING NEW INSTALLATION
AP500 FAULT FINDING NEW INSTALLATION This Bulletin covers the AP500 model which is identified by a black plastic Electronic Module with a silver printed label. This module would normally be mounted behind
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1998 Pontiac Bonneville 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Cruise Control System Buick; LeSabre Oldsmobile; Eighty Eight, LSS & Regency Pontiac; Bonneville * PLEASE
More informationCRUISE CONTROL SPEED LIMITER
Dealer address details: 39 INSTALLATION MANUAL CRUISE CONTROL & SPEED LIMITER AP900Ci SL900CiSeries 231.0005060 Rev. 1.0 f FOREWORD: This installation manual is written for installers with knowledge of
More information-Cruise. Installation instructions for Toyota Avensis 25x serie models Toyota Corolla Verso models Lindgaard Pedersen A/S
-Cruise Installation instructions for Toyota Avensis 25x serie models 2004-2009 Toyota Corolla Verso models 2004-2009 e-cruise e-cruise Page 1 / 6 Before installation. To make the installationen easier,
More information2001 Honda Civic EX ACCESSORIES & EQUIPMENT' 'Cruise Control Systems - Civic & CR-V 2001 ACCESSORIES & EQUIPMENT
DESCRIPTION 2001 ACCESSORIES & EQUIPMENT Cruise Control Systems - Civic & CR-V Cruise control system uses mechanical and electrically operated devices to maintain vehicle speed settings greater than 25
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1988 Jeep Cherokee 1988 Cruise Control Systems JEEP CRUISE COMMAND All Models DESCRIPTION & OPERATION Jeep vehicles use an electro-mechanical servo system. The system consists of
More informationDESCRIPTION & OPERATION
CRUISE CONTROL SYSTEM 1997 ACCESSORIES/SAFETY EQUIP General Motors Corp. - Cruise Control System DESCRIPTION & OPERATION WARNING: To avoid injury from accidental air bag deployment, read and carefully
More informationWARNING: DO NOT USE HAND-HELD 2-WAY TRANSCEIVERS INSIDE YOUR VEHICLE WHILE DRIVING.
CRC-2000 Drive-by-Wire Cruise Control System Introduction You have purchased one of the finest cruise control systems on the market. The cruise control features: Enhanced Adaptability Enhanced Features
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1994 Volvo 960 1994 ACCESSORIES/SAFETY EQUIPMENT Cruise Control System 960 DESCRIPTION & OPERATION MAIN SWITCH Cruise control main switch is located at end of directional signal lever.
More informationWARNING: DO NOT USE HAND-HELD 2-WAY TRANSCEIVERS INSIDE YOUR VEHICLE WHILE DRIVING.
CRC-1000 Drive-by-Wire Cruise Control System Introduction You have purchased one of the finest cruise control systems on the market. The cruise control features: Enhanced Adaptability Enhanced Features
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1994 Toyota Celica 1994 ACCESSORIES & EQUIPMENT Toyota Motor Sales, U.S.A., Inc. - Cruise Control Systems Celica DESCRIPTION Cruise control system consists of Cruise Control Electronic
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1993 Mitsubishi Montero 1993 ACCESSORIES & EQUIPMENT Mitsubishi Cruise Control Systems Montero DESCRIPTION & OPERATION The cruise control system is electronically and vacuum controlled.
More informationCruise Control Diagnosis
1999 Pontiac Firebird Cruise Control Diagnosis Circuit Description The Cruise Control system is a speed control system that maintains a desired vehicle speed under normal driving conditions. The cruise
More information2001 Chevrolet Corvette ACCESSORIES & EQUIPMENT Cruise Control Systems - Corvette
2001 ACCESSORIES & EQUIPMENT Cruise Control Systems - Corvette DESCRIPTION Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions. Steep grades
More informationInternational A26 (2017)
International A26 (2017) Overview: Cruise Control A26_CRUISE_CONTROL_06222017 Cruise Control TABLE OF CONTENTS General Overview: Cruise Control... 1 BASIC CRUISE CONTROL...1 ADVANCED CRUISE CONTROL...1
More informationOverview of operation modes
Overview of operation modes There are three main operation modes available. Any of the modes can be selected at any time. The three main modes are: manual, automatic and mappable modes 1 to 4. The MapDCCD
More informationOnGuard Display Operating Instructions
Issued 09-09 Technical Bulletin Issued 1 Technical 09-09 Bulletin OnGuard Display Operating Instructions Hazard Alert Messages Read and observe all Warning and Caution hazard alert messages in this publication.
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1992 Infiniti G20 1991-92 SAFETY EQUIPMENT Infiniti Cruise Control Systems G20, M30, Q45 DESCRIPTION & OPERATION NOTE: For system component locations, see SYSTEM COMPONENT LOCATIONS.
More informationINSTALLATION GUIDE Table of Contents
CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9625 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY DESCRIPTION
More informationULTRACRUISE CONTROL INSTALLATION MANUAL
ULTRACRUISE CONTROL INSTALLATION MANUAL Installation Operation Trouble Shooting FORM # 2784 Rev. A 07/95 THIS MANUAL, YOUR KIT AND YOU This Cruise Control Kit is a microprocessor based Cruise Control.
More informationHonda Accord/Prelude
Honda Accord/Prelude 1984-1995 In Tank Fuel Pumps TEST 1. Turn the ignition OFF. 2. On the Accord, remove the screws securing the underdash fuse box to its mount. Remove the fuel cut off relay from the
More information1. Cruise Control CRUISE CONTROL A: OPERATION CC-2
W1860BE.book Page 2 Tuesday, January 28, 2003 11:01 PM 1. Cruise Control A: OPERATION The cruise system automatically s the vehicle speed. It allows the vehicle to run at a constant speed without need
More informationCRUISE CONTROL SYSTEM
Negative (-) Battery Terminal CRUISE CONTROL CRUISE CONTROL SYSTEM Cable System name METER / GAUGE SYSTEM D033496E01 CRUISE CONTROL SYSTEM PRECAUTION 1 1. DISCONNECT AND RECONNECT CABLE OF NEGATIVE BATTERY
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9627 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: ALL MODELS (AT/MT) RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
HYUNDAI ACCENT 2010- /ELANTRA 2012- / KIA RIO 2012- PART NUMBER: 250-9628-NS GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: (AT/MT) VEHICLES RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9625 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY DESCRIPTION
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
GENERAL APPLICABILITY FORD FIESTA ( AT/MT) KIT CONTENTS/SERVICE PARTS ITEM QTY DESCRIPTION PART# 1 1 CRUISE CONTROL MODULE 250-2813 2 1 SWITCH HARNESS 250-2760 3 1 PEDAL INTERFACE HARNESS 250-2821 4 1
More informationDESCRIPTION & OPERATION
DESCRIPTION & OPERATION DESCRIPTION 1991-92 ACCESSORIES & SAFETY EQUIPMENT Cruise Control - Electric Servo Cruise control system components include cruise control module (control module and electric stepper
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
MITSUBISHI MIRAGE 2013- PART NUMBER: 250-9633 GENERAL APPLICABILITY ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY DESCRIPTION PART# 1 1 CRUISE
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9631 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: ALL MODELS (AT/MT) RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY
More informationUNIVERSAL ELECTRA-STEER FOR 2 COLUMN 220w Plain w Polished w Plain w Polished
UNIVERSAL ELECTRA-STEER FOR 2 COLUMN 220w Plain 8052810 220w Polished 8052610 360w Plain 8052780 360w Polished 8052760 Full refund will NOT be granted to any kits that are damaged, scratched, or altered
More informationAutomated Control Electronics (ACE ) System Operation and Diagnostics
Commercial Products Automated Control Electronics (ACE ) System Operation and Diagnostics PART NO. 98962SL This page is intentionally blank. Table of Contents Introduction... 1 Controller Operation and
More informationWiring Main Power connector constant 12V power
DHC-2000 Digital Height Control System Introduction This control system can be connected to a display module and height sensors or pressure senders to allow monitoring and control of all four corners and
More informationInstalling the Throttle Commander Ford F250 F550 Super Duty
Installing the Throttle Commander Ford F250 F550 Super Duty 6.0 L Power Stroke Diesel 2003.25 2004 T500082, T500083 and T500084 1.0 Preparing for Installation...5 2.0 Installing the Throttle Control Box...5
More informationCP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM
CP 634 DELUXE 4-CHANNEL KEYLESS ENTRY SYSTEM Installation And Operation Manual MEGATRONIX VAN NUYS, CA U.S.A. CP634 1 REMOTE CONTROL CONVENIENT SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION
More informationMaxxForce DT, 9, 10 ( )
MaxxForce DT, 9, 10 (2007-2009) Overview: TABLE OF CONTENTS General Overview:... 1 Description and Operation... 1 OPERATION...1 Programmable Parameters... 2 Parameter Setup... 2 Frequently Asked Questions...
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL 1. Cruise Control A: OPERATION The cruise control system automatically controls the vehicle speed. It allows the vehicle to run at a constant speed without need for the driver to keep the
More informationHigh Idle Kit Dodge Cummins (24 valve) Dodge Cummins (with APPS on motor) PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
U 6 May 2014 (1036620-27) 1998.5-2014 Dodge / GMC High Idle Kit (I-00321) 1 High Idle Kit 1036620 1998.5 2002 Dodge Cummins (24 valve) 2003-2004 Dodge Cummins (with APPS on motor) 1036621 2005-2006 Dodge
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM CONTROL SYSTEM PARTS LOCATION CRUISE CONTROL CRUISE CONTROL SYSTEM 1 ENGINE ROOM R/B AND J/B MAIN BODY ECU (INSTRUMENT PANEL J/B) B142328E05 2 CRUISE CONTROL CRUISE CONTROL SYSTEM
More informationSPEED SHIFT/TWO-STEP MODULE INSTALLATION MANUAL
SPEED SHIFT/TWO-STEP MODULE INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS
More informationVS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1
VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1 VS 315 2 INSTALLATION We recommend insulating all your soldered or crimped connections
More information218 Trademark Dr Buda Texas STL Supreme II Control Switch Box(U.S. Patent Pending) Operation Manual and Instructions
STL Supreme II Control Switch Box(U.S. Patent Pending) Operation Manual and Instructions Congratulations, you are the owner of a STL Supreme II Control Switch Box! Your bar is equipped with the latest
More informationManufacturing & Service: Bierer & Associates Inc. Patent No. 6,885,180. ST Series Service Tester Phase Identifier Operating Instructions ST500PGN
Manufacturing & Service: Bierer & Associates Inc. Patent No. 6,885,180 ST Series Service Tester Phase Identifier Operating Instructions ST500PGN REV. ED. 101229 CONTENTS Limitation of Warranty and Liability
More informationMaxxForce 11 and 13 ( )
MaxxForce 11 and 13 (2007-2009) Overview: TABLE OF CONTENTS General Overview:... 1 Description and Operation... 1 OPERATION...1 Programmable Parameters... 2 Parameter Setup... 3 Frequently Asked Questions...
More informationMICROCRUISE 4. INSTALLATION and OWNER S MANUAL FORM #2756, REV. E,
MICROCRUISE 4 INSTALLATION and OWNER S MANUAL FORM #2756, REV. E, 07-30-09 THIS MANUAL, YOUR KIT AND YOU This Cruise Control Kit is a microprocessor based Cruise Control. It is designed for ease of installation
More informationSECTION 1 7 OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake
SECTION 1 7 OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch.............................................. 114 Automatic transmission.....................................
More informationAS-4000 OPERATING INSTRUCTIONS (PS-5000)
AS-4000 OPERATING INSTRUCTIONS (PS-5000) BASIC OPERATIONS This unit is a state-of-the-art combination of a vehicle alarm and remote starter system. Start by familiarizing yourself with the alarm functions
More informationElectronic Engine Power Control (EPC) (E-Gas), checking
Page 1 of 51 24-113 Electronic Engine Power Control (EPC) (E-Gas), checking E-Gas system, function For E-Gas, the throttle valve is not operated by a cable from the accelerator pedal. There is no mechanical
More informationCA 421 Installation Instructions
CA 421 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More information1. Cruise Control CRUISE CONTROL A: OPERATION B: LOCATION OF COMPONENTS. CC(STi)-2
W1860BE.book Page 2 Tuesday, January 28, 2003 11:01 PM 1. Cruise Control A: OPERATION The cruise control system automatically controls the vehicle speed. It allows the vehicle to run at a constant speed
More informationI. CONNECTING TO THE GCU
I. CONNECTING TO THE GCU GCU7 and newer units use CAN BUS to connect to the computer so special interface is needed. GCU Interface uses FTDI drivers which are usually already installed by default. If you
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
2014 FORD TRANSIT FULL SIZE PART NUMBER: 250-9636 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: FORD TRANSIT 150, 250 RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationMAKE OF AUTOMOBILE: ENGINE SET NUMBER 345/ NUMBER : 076/ DATE : VERSION NR : B
MAKE OF AUTOMOBILE: TYPE: LOGAN PISTON DISPLACEMENT: 1600 NUMBER OF VALVES: 8 ENGINE NUMBER: K7M 710 TRANSMISSION TYPE ( MT / AT ) MT VEHICLE CATEGORIES M or N ( M ) TYPE VSI INJECTOR ( NUMBER + COLOR
More informationPressing and holding the + RES switch, when the Cruise Control System is engaged, will allow the vehicle to
CRUISE CONTROL DESCRIPTION AN... CRUISE CONTROL DESCRIPTION AND OPERATION (CRUISE CONTROL) Document ID# 2088041 Cruise Control Description and Operation Cruise control is a speed control system that maintains
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9632 GENERAL APPLICABILITY SUBARU IMPREZA (MT/AT) RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY DESCRIPTION PART# 1 1 CRUISE CONTROL
More informationCA-510a Installation Instructions
CA-510a Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationINSTALLATION GUIDE. FCC ID NOTICE
REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This
More informationCar Specific Installation manual for AP800 Drive by Wire cruise Control
Car Specific Installation manual for AP800 Drive by Wire cruise Control Only suitable for Peugeot, Citroen, Suzuki Grand Vitara and Fiat Scudo with potentiometer in engine bay and combination with Harness
More informationGENERAL <ELECTRICAL>
00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................... 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION FOR DIAGNOSIS.......
More informationPart 1 OPERATION OF INSTRUMENTS AND CONTROLS
Part 1 OPERATION OF INSTRUMENTS AND CONTROLS Chapter 1-6 Ignition switch, Transmission and Parking brake Ignition switch with steering lock Automatic transmission Manual transmission Four-wheel drive system
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9618 AUTOMATIC TRANSMISSION 250-9619 MANUAL TRANSMISSION GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: CHEVY SONIC/ SPARK (ALL MODELS) RECOMMENDED TOOLS PERSONAL & VEHICLE
More informationMain 20 A fuse has blown (2) Connector has come off PCB
ELECTRICAL FAULT FINDING OMS TRACTORS C & A from September 00 D&K series from April 00 JCB from Jan 00 Note: This Bulletin must be used in conjunction with the correct wiring diagram for the Tractor being
More informationWOT Box Installation Instructions VW / Audi
Connector Pinout Pin Color AWG Name WOT Box Installation Instructions VW / Audi Description 1 Yellow 18 RPM Connect to Fuel Injector Drive Signal or Ignition Control Signal (varies by car model) 2 Black
More informationSPEED CONTROL SYSTEM
DN SPEED CONTROL SYSTEM 8H - 1 SPEED CONTROL SYSTEM TABLE OF CONTENTS page AND SPEED CONTROL SYSTEM...1 SPEED CONTROL SERVO....2 SPEED CONTROL SOLENOID CIRCUITS...2 SPEED CONTROL SWITCHES...2 BRAKE LAMP
More informationDealing with customer concerns related to electronic throttle bodies By: Bernie Thompson
Dealing with customer concerns related to electronic throttle bodies By: Bernie Thompson In order to regulate the power produced from the gasoline internal combustion engine (ICE), a restriction is used
More informationUNISTEER Performance Products UNIVERSAL HOT ROD ELECTRA-STEER KIT
UNISTEER Performance Products UNIVERSAL HOT ROD ELECTRA-STEER KIT 8051500 BEFORE YOU START PLEASE READ! Designing steering systems requires an understanding of steering function and design. If you are
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-1873 GENERAL APPLICABILITY ALL MODELS RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS ITEM QTY DESCRIPTION PART# 1 1 CRUISE CONTROL MODULE 250-2791
More informationBASIC TROUBLE SHOOTING (PERFECTPASS FOR MECHANICAL ENGINES) How PerfectPass Works
BASIC TROUBLE SHOOTING (PERFECTPASS FOR MECHANICAL ENGINES) How PerfectPass Works Through the in-dash display the driver sets the desired boat speed or engine RPM depending upon which mode of operation
More informationTransfer Control Device
Page 1 of 9 2005 Nissan Xterra 4.0L Eng S Transfer Control Device CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE Data are reference value. DATA MONITOR MODE REFERENCE Monitored item [Unit] Content Condition
More informationINTRODUCTION ALARM WIRING DESCRITION
6PIN CONNECTION RED BLUE YELLOW BROWN PINK INTRODUCTION The newest technological are integrated in our Two Way Alarm and Remote Engine Start alarm system. They are fully programmable for your customers
More informationMapDCCD Version 2 Installation and setup guide
MapDCCD Version 2 Installation and setup guide Overview of operation modes There are three main operation modes available. Any of the modes can be selected at any time. The three main modes are: manual,
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
PART NUMBER: 250-9545 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON:2.7,3.3, 3.5, 5.0 FORD F-150 RECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES KIT CONTENTS/SERVICE PARTS
More informationA U T O M A T I C T R A N S M I S S I O N M U L T I - C H A N N E L T W O - W A Y L C D R E M O T E S T A R T E R AS-2510 TW.
A U T O M A T I C T R A N S M I S S I O N M U L T I - C H A N N E L T W O - W A Y L C D R E M O T E S T A R T E R S Y S T E M AS-2510 TW User Guide Transmitter Part Number and Module Serial Number...2
More informationMAKE OF AUTOMOBILE: GRAND CHEROKEE PISTON DISPLACEMENT: 5700 NUMBER OF VALVES: 16
MAKE OF AUTOMOBILE: TYPE: GRAND CHEROKEE PISTON DISPLACEMENT: 5700 NUMBER OF VALVES: 16 ENGINE NUMBER: 5.7V8 HEMI TRANSMISSION TYPE ( MT / AT ) AT VEHICLE CATEGORIES M or N M TYPE VSI INJECTOR ( NUMBER
More informationEFIE Wideband O2 (Electronic Fuel Injector Enhancer) Installation & Operating Instructions.
EFIE Wideband O2 (Electronic Fuel Injector Enhancer) Installation & Operating Instructions. The EFIE is not intended to be a fuel saver by itself. The EFIE is designed to be used in conjunction with fuel
More informationCHERY P Wiring Description Fitting Instructions Tools Required Calibration
CHERY P5 2014 Wiring Description Fitting Instructions Tools Required Calibration The Drive by Wire kit supplied by Autokontrol must only be fitted by accredited installer as certified by Autokontrol Limited.
More informationGo Yonder D-Lite Owner s Manual
Go Yonder D-Lite Owner s Manual Marketed in Australia and New Zealand by Bzooma Pty Ltd ABN 37 640 907 507 TABLE OF CONTENTS Table of Contents... 1 Bzooma Pty Ltd... 1 Introduction... 1 Operation... 1
More informationInstalling the Throttle Commander
Installing the Throttle Commander Ford 6.0L Diesel Powerstroke 2005-2007 F250-550 Super Duty 2005-2010 E250-550 Econoline (8500+ GVW) Ford 6.4L Diesel Powerstroke 2008-2010 F250-550 Super Duty T500107
More informationKTM Motorcycle 1050/1190/Super Duke
1/21/2016 Brandon Distributing, Inc. 2013-2016 KTM Motorcycle 1050/1190/Super Duke AP 900cm Doc#1191 Installation Guide With OBD Connector 763-241-4172 www.brandondist.com Parts included in this kit. 8500-RS
More informationCT6 SUPER CRUISE Convenience & Personalization Guide. cadillac.com
2018 CT6 SUPER CRUISE Convenience & Personalization Guide cadillac.com Review this guide for an overview of the Super Cruise system in your Cadillac CT6. Your complete attention is required at all times
More information1993 ACCESSORIES & EQUIPMENT Volkswagen Cruise Control Systems. Volkswagen; Corrado SLC, EuroVan, Passat
Article Text ARTICLE BEGINNING 1993 ACCESSORIES & EQUIPMENT Volkswagen Cruise Control Systems Volkswagen; Corrado SLC, EuroVan, Passat DESCRIPTION & OPERATION The cruise control system allows driver to
More informationSECOND GENERATION Use this guide with unit serial number prefix beginning with BWF using Terra Power separator.
Technical Information and Diagnostic Guide for SECOND GENERATION Use this guide with unit serial number prefix beginning with BWF using Terra Power separator. This guide will assist you in becoming more
More informationQUICK INSTALLATION GUIDE
MANUAL/AUTOMATIC T R A N S M I S S I O N 2 - B U T T O N R E M O T E S T A R T E R W I T H V I R T U A L T A C H S Y S T E M ( A S P R G - 1 0 0 0 C O M P A T I B L E ) QUICK INSTALLATION GUIDE Manual
More informationPlease check our application list to see if we have a specific Harness Kit available for your motorcycle.
GIpro X-type Install Guide for GPX-WSS Harness Kit Compatibility: This universal harness kit includes a Wheel Speed Sensor and will fit all motorcycles and vehicles which have electronic ignition system.
More informationCRUISE CONTROL SYSTEM
CRUISE CONTROL CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM PRECAUTION 1 1. NOTICE FOR INITIALIZATION NOTICE: When the cable of the negative () battery terminal is disconnected, initialize the following
More informationRECOMMENDED TOOLS PERSONAL & VEHICLE PROTECTION SAFETY GLASSES
HYUNDAI ACCENT 2012-18 /ELANTRA 2012-16 / KIA RIO 2012-2018 KIO FORTE 2014-18 PART NUMBER: 250-1862 GENERAL APPLICABILITY THIS CRUISE WAS TESTED AND VERIFIED ON: (AT/MT) VEHICLES RECOMMENDED TOOLS PERSONAL
More informationPowerLevel s e r i e s
Owner s Manual Hydraulic Leveling CONTENTS Introduction Operation Control Panel Automatic Leveling Manual Leveling Retracting Jacks Remote Operation Care & Maintenance Troubleshooting Error Codes 1 2 2
More informationELECTRONIC POSITIVE AIR SHUTOFF
12 January 2015 103675X Electronic positive air shutdown (I-00336) 1 ELECTRONIC POSITIVE AIR SHUTOFF 1036750 2007-2009 Dodge 6.7L 1036751 2010-2015 Dodge 6.7L 1036754 2008-2010 Ford 6.4L 1036755 2011-2014
More informationFORD ECOSPORT Quick Reference Guide
FORD ECOSPORT Quick Reference Guide About This Quick Reference Guide We have created this guide to help you get to know certain features of your vehicle quickly. It only contains basic instructions to
More information2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE
REV. ARS. WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This device may not cause
More informationCT6 SUPER CRUISE Convenience & Personalization Guide. cadillac.com
2018 CT6 SUPER CRUISE Convenience & Personalization Guide cadillac.com Review this guide for an overview of the Super Cruise system in your CT6. Your complete attention is required at all times while driving,
More information