Loctite Spray Valve Controller Part Number EQUIPMENT Operation Manual

Size: px
Start display at page:

Download "Loctite Spray Valve Controller Part Number EQUIPMENT Operation Manual"

Transcription

1 Label P/N: EQUIPMENT Operation Manual FOR SPARE PARTS, MANUALS, REPAIRS, OR TECHNICAL ASSISTANCE: Visit us at equipment.loctite.com or call Henkel Corp. at: USA - (1) Germany - (49) Singapore - (65) WARNING: Unplug power cord and disconnect air supply prior to removing cover. P/N: MODE DECIMAL PORT A PORT B MODE/TIME SET MODE/TIME DISPLAY Loctite Spray Valve Controller Part Number 98521

2 Table of Contents 1 Please Observe The Following Emphasized Sections For Your Safety Unpacking and Inspection Items supplied Description Technical Data Installation Space requirements Features Description Fuse Installation/Voltage Selection Assembly Connecting the unit I/O Configuration and End of Cycle Switching Operation Mode Menu Manual spray cycle setting: Automatic Spray cycle setting Troubleshooting Care and Maintenance Accessories and Spare Parts Appendix Electrical Diagram Pneumatic Diagram Warranty... 13

3 1 Please Observe The Following 1.1 Emphasized Sections Warning! Refers to safety regulations and requires safety measures that protect the operator or other persons from injury or danger to life. Caution! Emphasizes what must be done or avoided so that the unit or other property is not damaged. Notice: Gives recommendations for better handling of the unit during operation or adjustment as well as for service activities. 1.2 For Your Safety For safe and successful operation of the unit, read these instructions completely. If the instructions are not observed, the manufacturer can assume no responsibility. To ensure proper voltage setting, all units are shipped from the factory with the Fuse Holder/Voltage Selector disassembled from the AC Connector Do not expose the connecting cable to heat, oil, or sharp edges. Make sure the Unit stands stable and secure. Use only original equipment replacement parts. Always disconnect the power supply before servicing the unit. Observe general safety regulations for the handling of chemicals such as Loctite adhesives and sealants. Observe the manufacturer s instructions as stated in the Material Safety Data Sheet (MSDS). While under warranty, the unit must be repaired by an authorized Loctite brand service representative.

4 1 Please Observe The Following (continued) 1.3 Unpacking and Inspection Carefully unpack the Loctite Spray Valve Controller and examine the items contained in the carton. Inspect the unit for any damage that might have occurred in transit. If such damage has occurred, notify the carrier immediately. Claims for damage must be made by the consignee to the carrier and should be reported to the manufacturer. 1.4 Items supplied Controller Unit Power Cord & Cord Lock Foot Pedal Item #98461 Air Supply Line, 5 micron Filter & Fittings Fuse Assembly and Fuses (0.25 amp & 0.1 amp) 2 Description The Loctite Spray Valve Controller is a microprocessor based control unit that provides a 3-segment time sequenced spray cycle for the Loctite Spray Valve The unit allows individual programming for each time segment Pre-spray atomizing Valve on time Post spray atomizing These individually controlled time ranges provide for complete atomization of a wide variety of fluid and ensure no-drip positive valve shut-off. When the spray cycle is activated by depressing the Foot Switch, a pulse of air through Port A is transmitted to the valve air cylinder to open the valve and a second pulse of air through Port B is transmitted to the valve s spray cap to spray the fluid. The amount of fluid sprayed is controlled by the spray cycle on time, fluid pressure and stroke setting on the Loctite Spray Valve.

5 3 Technical Data 1. SPECIFICATIONS a) Size W=9.2 in. (23.4 cm) D=8.1 in. (20.6 cm) H=2.4 in. (6.1 cm) b) Weight 4.5 lbs (2.0 kg) VAC 60 Hz c) Input Voltage VAC 50 Hz Mains voltage fluctuation not to exceed 10% of nominal voltage Fluctuation max: 10% d) Rated Power 20W e) Air Input 100 Psi (689 Kpa) max f) Internal Voltage 24VDC g) Indoor Use Altitude up to 2,000 m h) Operating Temperature 0 o F to 120 o F (-18 o C to +50 o C) i) Maximum Relative Humidity 80% for temperature up to 31 o C Decrease linearly to 50% relative humidity at 40 o C j) Air Output 100 psi (689 Kpa) Max. k) Timer Programmable Sec. l) Cycle Initiation Maintained or Momentary m) Repeat Tolerance +/- 0.05% p) Cycle Rate 900 cycles/minute

6 FOR SPARE PARTS, MANUALS, REPAIRS, OR TECHNICAL ASSISTANCE: Visit us at equipment.loctite.com or call Henkel Corp. at: USA - (1) Germany - (49) Singapore - (65) Label P/N: Installation 4.1 Space requirements 6.1 [156.0MM] 7.6 [194.3MM] WARNING: Unplug power cord and disconnect air supply prior to removing cover. P/N: [316.0MM] MODE DECIMAL 2.3 [57.8MM] PORT A PORT B 2.5 [63.1MM] MODE/TIME SET MODE/TIME DISPLAY 4.2 Features Description MADE IN USA AIR IN SERIAL NO ACC. OUT MODE DECIMAL PORT A PORT B MODE/TIME SET MODE/TIME DISPLAY Item Function 1. Power Switch Turn power on to the unit 2. Air Pressure Gauge Displays dispense air pressure 3. Air Pressure Regulator Regulates dispense air pressure 4. Port A Provide valve actuating air signal 5. Port B Provide atomizing air signal 6. Mode/Time Set Scrolls menu/adjusts dispense time 7. Display Displays time, voltage and mode setting 8. Decimal Switch Change decimal point position

7 4 Installation (continued) 9. Mode Switch Indicates mode setting 10. AC Connection with Fuse Holder Connects to AC power supply. Provides pull out for easy fuse replacement. 11. Foot Switch Receptacle Activates dispense circuit 12. I/O Connection Provides alternate activation source 13. Air Inlet Air supply connection 14. Accessory Air Outlet Provide constant unregulated air outlet 4.3 Fuse Installation/Voltage Selection Assembly 1. The AC Connector on the rear panel of the unit is the Fuse holder and the Voltage Selector. 2. To ensure proper voltage setting, all units are shipped from the factory with the Fuse Holder/Voltage Selector disassembled from the AC Connector. "X" V~ VOLTAGE SETTING VOLTAGE RANGE FUSE RATING 100 NOT CONNECTED V-120V.250 Amp, Type F 220 NOT CONNECTED V-240V.100 Amp, Type T

8 4 Installation (continued) 3. Using the chart (previous page), select Fuse & Voltage setting required. 4. If the voltage in not correctly set, remove the voltage selector from the fuse holder and reinstall it with the desired voltage shown at the window of the fuse holder. NOTE: Make certain fuse replacement is proper type and rating. 5. Reinsert the fuse holder into the AC Connector casing until it snaps into place. 4.4 Connecting the unit 1. Connect psi dry, filtered air supply to air inlet fitting. Make sure the air inlet pressure is at least 70 psi. The 5-micron filter should be installed with the unit to ensure proper air filtration Install the cord lock to the cord lock mount with the slot at the bottom. 3. Lift the cord lock and connect the foot switch plug to foot switch receptacle. 4. Fit the cord lock over the foot switch cable. 5. For circuit protection, the unit is shipped with fuse unassembled. Follow instructions in the Fuse Installation section 4.3 to install fuse and set proper voltage. 6. Connect the power cord to a grounded, properly rated voltage outlet. Connect the valve air hose to Port A and atomizing air hose. 4.5 I/O Configuration and End of Cycle Switching Upon completion of a dispense cycle, an open collector circuit closes and remains closed until the next dispense cycle. This circuit can be used to signal back to a host computer, start another device in sequence, or drive any other operations that needs to be tied to the completion of the dispense cycle. Upon closure, (end of dispense cycle), power from an external source is allowed to pass through the circuit to operate a 5 to 24 VDC load. Power consumption must not exceed 250 ma. The load could be a relay, solenoid, counter, LED, or any device that will operate within a 5 to 24 VDC range and a maximum of 250 ma.

9 4 Installation (continued) 5 Operation 5.1 Mode Menu DISPLAY SP-1 SP-2 SP-3 FUNCTION Pre-spray time Atomized air turns on for preset time before valve opens Valve on time Actual Spraying time Post-spray time Atomized air spray stays on for preset time after valve closed

10 5 Operation (continued) 5.2 Manual spray cycle setting: 1. Turn on the unit by switching the Power Switch (1) to the ON position. The switch should light up in the ON position. 2. Set atomizing air pressure by rotating the Air Pressure Regulator Knob (3) until the desired pressure is indicated on the Air Pressure Gauge (2). 3. Push the Mode Switch (9) and rotate Mode /Time Set Knob (6) until SP-1 appears in the display. 4. Push the Mode Switch (9) a second time to set the Pre-spray cycle time 5. Push the Mode Switch (9) and rotate Mode /Time Set Knob (6) until SP-2 appears in the display. 6. Push the Mode Switch (9) a second time and set the time to 0 7. Push the Mode Switch (9) and rotate Mode /Time Set Knob (6) until SP-3 appears in the display. 8. Push the Mode Switch (9) a second time to set the Post-spray cycle time. 9. Depress and hold on to foot switch to activate timed dispensed cycle. 5.3 Automatic Spray cycle setting 1. Push the Mode Switch (9) and rotate Mode /Time Set Knob (6) until SP-1 appears in the display. 2. Push the Mode Switch (9) a second time to set the Pre-spray cycle time. 3. Push the Mode Switch (9) and rotate Mode /Time Set Knob (6) until SP-2 appears in the display. 4. Push the Mode Switch (9) a second time to set spray cycle time. 5. Push the Mode Switch (9) and rotate Mode /Time Set Knob (6) until SP-3 appears in the display. 6. Push the Mode Switch (9) a second time to set the Post-spray cycle time 7. Depress foot switch to activate timed dispensed cycle. 8. To change the amount of fluid sprayed, increase or decrease atomized pressure, valve open time, or valve stroke. NOTE: In both Manual and Automatic Mode, pre-spray time and post spray time must be entered in the unit, otherwise the unit will not activate. NOTE: All spray time entered into the Controller will be stored in its memory even with the unit disconnected from the AC source. All entries can be cleared from the memory by turning the unit off, then back on while holding the Decimal Switch (8)

11 6 Troubleshooting PROBLEM POSSIBLE CAUSE CORRECTION Power light, not on No Power input Fuse open Power Switch not ON Power Switch defective Check Power Cord connections and Power Supply Replace Fuse Turn on Power Switch Replace Power Switch System will not actuate Foot Switch not plugged in or improperly plugged in Defective Foot Switch Broken wire or loose connection inside unit System will not pressurize Defective Solenoid Defective Timer Board Unit in Menu Mode No time set in SP-1 and SP-3 Insufficient air pressure Air hoses not plugged in Regulator defective Inconsistent spray Air bubbles in fluid Spray valve damage Check Foot Switch connection Foot Switch needs to be repaired or replaced. Unplug Power Cord and disconnect air supply. Remove cover and check for broken wires or loose connections Replace Solenoid Replace Timer Board Press Mode Switch to change to activation mode Enter desired pre-spray time in SP-1 and post-spray time in SP-3 Increase air supply pressure Check connection Replace Regulator Remove air from fluid Refer to Spray valve manual 7 Care and Maintenance The dispenser is designed and built to be relatively maintenance free. To assure trouble free operation, the following recommendations should be followed: 1. Make certain air supply is clean and dry. 2. Make certain AC outlet is grounded and of proper voltage rating. 3. Avoid turning Adhesive barrels upside down or laying barrel so that material may run through airline to internal components. 4. Avoid connecting the unit to excessive moisture or solvent saturation. 5. Avoid connecting the unit to air supply exceeding 100 psi. 6. Always replace fuse with proper type and amperage rating. 8 Accessories and Spare Parts Foot Pedal micron Air Filter

12 9 Appendix 9.1 Electrical Diagram TIMER BOARD ATOMIZING SOLENOID ORG ORG RED ORG RED YEL QUADRATURE POT BRN + BLU - OUTPUT SIGNAL RED YEL GND +24V RED +24V COM +36V GND +10V GRN BLU +10V VALVE SOLENOID POWER SUPPLY BLU BLU 24VDC INITIATE BRN WHT WHT WHT COM FS AUTO SHOT WHT RED ORG RED + - WHT FOOT SWITCH FOOT SWITCH CONNECTOR GRN MODE SW DECIMAL SW MODE LED DECIMAL LED DISPLAY GND BRN 3 POWER SWITCH GRN 9.2 Pneumatic Diagram Air Inlet Air Outlet Air Manifold 3 Solenoid Valve 2 1 Regulator Air Pressure Gauge Air Outlet Air Outlet (White) Solenoid Valve

13 10 Warranty Henkel expressly warrants that all products referred to in this Instruction Manual for (Loctite Spray Valve Controller ) (hereafter called Products ) shall be free from defects in materials and workmanship. Liability for Henkel shall be limited, as its option, to replacing those Products which are shown to be defective in either materials or workmanship or to credit the purchaser the amount of the purchase price thereof (plus freight and insurance charges paid therefor by the user). The purchaser s sole and exclusive remedy for breach of warranty shall be such replacement or credit. A claim of defect in materials or workmanship in any Products shall be allowed only when it is submitted in writing within one month after discovery of the defect or after the time the defect should reasonably have been discovered and in any event, within (12) months after the delivery of the Products to the purchaser. This warranty does not apply to perishable items, such as, but not limited to: (o-rings, seals, gaskets, washers, filters, tubing, fittings, lights, etc.). No such claim shall be allowed in respect of products which have been neglected or improperly stored, transported, handled, installed, connected, operated, used or maintained. In the event of unauthorized modification of the Products including, where products, parts or attachments for use in connection with the Products are available from Henkel, the use of products, parts or attachments which are not manufactured by Henkel, no claim shall be allowed. No Products shall be returned to Henkel for any reason without prior written approval from Henkel. Products shall be returned freight prepaid, in accordance with instructions from Henkel. NO WARRANTY IS EXTENDED TO ANY EQUIPMENT WHICH HAS BEEN ALTERED, MISUSED, NEGLECTED, OR DAMAGED BY ACCIDENT, OR IF THE SYSTEM WAS USED TO DISPENSE ANY LIQUID MATERIAL OTHER THAN LOCTITE PRODUCTS. EXCEPT FOR THE EXPRESS WARRANTY CONTAINED IN THIS SECTION, HENKEL MAKES NO WARRANTY OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS. ALL WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND OTHER WARRANTIES OF WHATEVER KIND (INCLUDING AGAINST PATENT OR TRADEMARK INFRINGEMENT) ARE HEREBY DISCLAIMED BY HENKEL AND WAIVED BY THE PURCHASER. THIS SECTION SETS FORTH EXCLUSIVELY ALL OF LIABILITY FOR HENKEL TO THE PURCHASER IN CONTRACT, IN TORT OR OTHERWISE IN THE EVENT OF DEFECTIVE PRODUCTS. WITHOUT LIMITATION OF THE FOREGOING, TO THE FULLEST EXTENT POSSIBLE UNDER APPLICABLE LAWS, HENKEL EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY IN CONNECTION WITH THE SALE OR USE OF, OR OTHERWISE IN CONNECTION WITH, THE PRODUCTS, INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS AND SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER CAUSED BY NEGLIGENCE FROM HENKEL OR OTHERWISE.

14 Henkel Corporation 1001 Trout Brook Crossing Rocky Hill, CT Henkel Automotive Technology Center 2455 Featherstone Road Auburn Hills, Michigan Henkel Canada Corporation 2225 Meadowpine Boulevard Mississauga, Ontario L5N 7P2 Henkel Ltda. Rua Karl Huller, 136 Jd. Canhema Diadema/SP, Brazil Henkel Capital, S.A. de C.V. Calzada de la Viga s/n Fracc. Los Laureles Loc. Tulpetlac, C.P Ecatepac de Morelos, Edo. de México Loctite is a trademark of Henkel Corporation, U.S.A. Copyright Henkel Corporation All rights reserved. Data in this operation manual is subject to change without notice. Manual P/N: , Date: 04/2005

Loctite Spray Valve Controller Part Number EQUIPMENT Operation Manual

Loctite Spray Valve Controller Part Number EQUIPMENT Operation Manual Loctite Spray Valve Controller Part Number 1406023 EQUIPMENT Operation Manual Table of Contents 1 Please Observe The Following 3 1.1 Emphasized Sections 3 1.2 For your Safety 3 1.3 Unpacking and Inspection

More information

Loctite Control Timer Part Number EQUIPMENT Operation Manual. Control Timer SEC. Technologies

Loctite Control Timer Part Number EQUIPMENT Operation Manual. Control Timer SEC. Technologies I EQUIPMENT Operation Manual Warning: Electrical Hazard Disconnect Power Cord Before Removing Cover. Advertencia: Peligro eléctrico Desconecte el cable eléctrico antes de quitar la cubierta. 115 VAC, 50/60

More information

MM10 Dual Cartridge Dispenser 1:1 & 2:1 A Style Cartridges MM10 Dual Cartridge Dispenser 1:1 & 2:1 B Style Cartridges

MM10 Dual Cartridge Dispenser 1:1 & 2:1 A Style Cartridges MM10 Dual Cartridge Dispenser 1:1 & 2:1 B Style Cartridges EQUIPMENT Operation Manual Loctite MM10 Dual Cartridge Dispensers 1633364 MM10 Dual Cartridge Dispenser 1:1 & 2:1 A Style Cartridges 1633365 MM10 Dual Cartridge Dispenser 1:1 & 2:1 B Style Cartridges 1633366

More information

ml Dual Cartridge Dispenser 10:1 B Style Cartridge ml Dual Cartridge Dispenser 1:1 & 2:1 B Style Cartridge

ml Dual Cartridge Dispenser 10:1 B Style Cartridge ml Dual Cartridge Dispenser 1:1 & 2:1 B Style Cartridge EQUIPMENT Operation Manual Loctite 50ml Dual Cartridge Dispenser 1444133 50ml Dual Cartridge Dispenser 10:1 B Style Cartridge 1444134 50ml Dual Cartridge Dispenser 1:1 & 2:1 B Style Cartridge 1444135 50ml

More information

Equipment Operation Manual. Loctite 250ml Bottle Hand Pump Part No Loctite 50ml Bottle Hand Pump Part No

Equipment Operation Manual. Loctite 250ml Bottle Hand Pump Part No Loctite 50ml Bottle Hand Pump Part No Equipment Operation Manual Loctite 250ml Bottle Hand Pump Part No. 97001 Loctite 50ml Bottle Hand Pump Part No. 98414 Description The Loctite 250ml Bottle Hand Pump (item # 97001) is a hand-held bottle-top

More information

Loctite 300ml Cartridge Pusher Part Number EQUIPMENT Operation Manual

Loctite 300ml Cartridge Pusher Part Number EQUIPMENT Operation Manual Loctite 300ml Cartridge Pusher Part Number 98022 EQUIPMENT Operation Manual Table Of Contents 1 PLEASE OBSERVE THE FOLLOWING... 3 1.1 EMPHASIZED SECTIONS...3 1.2 FOR YOUR SAFETY...3 1.3 ITEMS SUPPLIED...3

More information

Frekote Adjustable Spray Applicator 6 Extension Extension Extension EQUIPMENT Operation Manual

Frekote Adjustable Spray Applicator 6 Extension Extension Extension EQUIPMENT Operation Manual Frekote Adjustable Spray Applicator 6 Extension 98183 12 Extension 98184 24 Extension 98185 EQUIPMENT Operation Manual 1 Please Observe The Following 1.1 Emphasized Sections Warning! Refers to safety regulations

More information

EQUIPMENT. Loctite Bench Top Air Filtration System Plenum Style Part Number Air Filtration System With Arm Part Number

EQUIPMENT. Loctite Bench Top Air Filtration System Plenum Style Part Number Air Filtration System With Arm Part Number EQUIPMENT Operation Manual Loctite Bench Top Air Filtration System Plenum Style Part Number 98278 Loctite Bench Top Air Filtration System With Arm Part Number 98277 Contents Page No. 1 PLEASE OBSERVE THE

More information

EQUIPMENT Instructions. Loctite Pneumatic 300 ml Cartridge Dispenser Part Number

EQUIPMENT Instructions. Loctite Pneumatic 300 ml Cartridge Dispenser Part Number EQUIPMENT Instructions Loctite Pneumatic 300 ml Cartridge Dispenser Part Number 1294304 1. Unpacking and Inspection Carefully unpack the Loctite Pneumatic 300 ml Cartridge Dispenser and examine the items

More information

Loctite Micro Needle Valve Part Number EQUIPMENT Operation Manual

Loctite Micro Needle Valve Part Number EQUIPMENT Operation Manual Loctite Micro Needle Valve Part Number 98084 EQUIPMENT Operation Manual Table of Contents 1 PLEASE OBSERVE THE FOLLOWING... 3 1.1 EMPHASIZED SECTIONS... 3 1.2 FOR YOUR SAFETY... 3 1.3 UNPACKING AND INSPECTION...

More information

EQUIPMENT Operation Manual. Loctite RB10 Rotary Dispense System Part Number

EQUIPMENT Operation Manual. Loctite RB10 Rotary Dispense System Part Number EQUIPMENT Operation Manual Loctite RB10 Rotary Dispense System Part Number 1635546 1 Table of Contents 1 Please Observe The Following 3 1.1 Emphasized Sections 3 1.2 For Your Safety 1.3 Inspection 3 1.4

More information

EQUIPMENT Operation Manual. Loctite Zeta 7401 UV Chamber Part Number 98039

EQUIPMENT Operation Manual. Loctite Zeta 7401 UV Chamber Part Number 98039 EQUIPMENT Operation Manual Loctite Zeta 7401 UV Chamber Part Number 98039 1 Table of Contents 1 Please Observe The Following 3 1.1 Emphasized Sections 3 1.2 For Your Safety 3 1.3 Items Supplied 4 2 Description

More information

UV Flood Curing System

UV Flood Curing System UV EQUIPMENT Operation Manual 7411-S ITEM # 98413 Warning: UV Energy is transmitted from this unit. Protective eyewear equipped with side shields are required that meet ANSI Z80.3 & Z87.1 Certification.

More information

EQUIPMENT OPERATION MANUAL. Loctite ZETA 7401 UV Chamber

EQUIPMENT OPERATION MANUAL. Loctite ZETA 7401 UV Chamber EQUIPMENT OPERATION MANUAL Loctite ZETA 7401 UV Chamber 98039 Contents Page No. 1 Please observe the following...................................... 1 1.1 Emphasized Sections.............................................

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual Loctite Zeta 7735 UV Curing Wand System Part Number 98317 TABLE OF CONTENTS 1. PLEASE OBSERVE THE FOLLOWING...3 1.1 EMPHASIZED SECTIONS...3 1.2 ITEMS SUPPLIED...3 1.3 FOR YOUR

More information

EQUIPMENT Operation Manual AD988558

EQUIPMENT Operation Manual AD988558 EQUIPMENT Operation Manual AD988558 Loctite Pressure Rams Part Numbers 988536 Twin Post Ram, Carbon Steel, 55 Gal. 988539 Single Post Ram, Carbon Steel, 5 Gal. 988541 Twin Post Ram, Inert, 55 Gal. 988542

More information

EQUIPMENT Operation Manual. Loctite Zeta 7411 UV Flood Curing System. Part Number 98027

EQUIPMENT Operation Manual. Loctite Zeta 7411 UV Flood Curing System. Part Number 98027 EQUIPMENT Operation Manual Loctite Zeta 7411 UV Flood Curing System Part Number 98027 Table of Contents 1. PLEASE OBSERVE THE FOLLOWING... 3 1.1 EMPHASIZED SECTIONS... 3 1.2 FOR YOUR SAFETY... 3 1.3 ITEMS

More information

EQUIPMENT Operation Manual. Loctite Advancing Slide Dispense Station. Part Number 98426

EQUIPMENT Operation Manual. Loctite Advancing Slide Dispense Station. Part Number 98426 EQUIPMENT Operation Manual Loctite Advancing Slide Dispense Station Part Number 98426 1 Table of Contents 1. PLEASE OBSERVE THE FOLLOWING... 3 1.1 EMPHASIZED SECTIONS... 3 2. DESCRIPTION... 3 2.1 OPERATION...

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual TM EQUIPMENT Operation Manual START Panasonic TIMER POWER Single CureJet Controller Item # 1364033 TIMED MODE RESET UP CURE LIGHT ON LOCK LT4H DOWN FAULT MANUAL MODE For: LEDs Loctite Single CureJet TM

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual Loctite Part Numbers 97115 Rotorspray Contents Page No. 1 Please Observe the Following......................................... 1-2 1.1 Emphasized Sections...................................................

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual TM EQUIPMENT Operation Manual START Panasonic TIMER POWER Single CureJet Controller Item # 1364033 TIMED MODE RESET UP CURE LIGHT ON LOCK LT4H DOWN FAULT MANUAL MODE For: LEDs Loctite Single CureJet TM

More information

EQUIPMENT OPERATION MANUAL. Loctite Zeta 7740 UV Curing Wand System

EQUIPMENT OPERATION MANUAL. Loctite Zeta 7740 UV Curing Wand System EQUIPMENT OPERATION MANUAL Loctite Zeta 7740 UV Curing Wand System 98025 Contents Page No. 1 Please observe the following...................................... 1 1.1 Emphasized Sections.............................................

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual Loctite Dispense Valve Part Numbers 97113 and 97114 Contents Page No. 1 Please Observe the Following......................................... 1-2 1.1 Emphasized Sections...................................................

More information

Loctite Air Filtration System Part Number EQUIPMENT. Operation Manual

Loctite Air Filtration System Part Number EQUIPMENT. Operation Manual Loctite Air Filtration System Part Number 98276 EQUIPMENT Operation Manual Contents Page No. 1 PLEASE OBSERVE THE FOLLOWING................................... 1-2 1.1 EMPHASIZED SECTIONS...............................................

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual Loctite MMD Dispense Valve Manual Part Number 989027, 1:1-5:1 Abrasion Resistant 989096, 1:1-5:1 Stainless Steel 989098, 5.05:1 10:1 Stainless Steel 989099, 5.05:1 10:1 Abrasion

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual TIMER Exposure Time LT4H Lamp On RESET LOCK N is Timed UP DOWN Lamp Hours HOURS 1 10 UV CURTIS Warning: UV Energy is transmitted from the end of the light guide. Protective eyewear

More information

Equipment Operation Manual. CA Volumetric Hand Pump Part No

Equipment Operation Manual. CA Volumetric Hand Pump Part No Equipment Operation Manual CA Volumetric Hand Pump Part No. 1506477 Loading and Priming Screw bottle into Fluid Element Cap by turning bottle. Tighten with pliers Ensure that the lower Fluid Element Dispense

More information

EQUIPMENT OPERATION MANUAL. Loctite Dial-A-Seal Dispensing System

EQUIPMENT OPERATION MANUAL. Loctite Dial-A-Seal Dispensing System EQUIPMENT OPERATION MANUAL Loctite Dial-A-Seal Dispensing System 998400 Contents Page No. Please observe the following....................................... Emphasized Sections..............................................2

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual Light Cure Valve Part Number 98009 Cyanoacrylate Adhesive Valve Part Number 98013 Contents Page No. 1 Specifications..................................................... 1 2

More information

EQUIPMENT Operation Manual

EQUIPMENT Operation Manual EQUIPMENT Operation Manual CL15 UV Wand System Item No. 1661548 + Enter _ Warning: UV Energy is transmitted from the end of the light guide. Protective eyewear equipped with side shields are required that

More information

EQUIPMENT Operation Manual. Loctite Single Rotary Dispense Station. Part Number 98427

EQUIPMENT Operation Manual. Loctite Single Rotary Dispense Station. Part Number 98427 EQUIPMENT Operation Manual Loctite Single Rotary Dispense Station Part Number 98427 1 Table of Contents 1. PLEASE OBSERVE THE FOLLOWING... 4 1.1 EMPHASIZED SECTIONS... 4 2. DESCRIPTION... 4 2.1 OPERATION...

More information

Loctite 100W UV Curing Wand System Part Number EQUIPMENT Operation Manual

Loctite 100W UV Curing Wand System Part Number EQUIPMENT Operation Manual Loctite 100W UV Curing Wand System Part Number 1377200 EQUIPMENT Operation Manual TABLE OF CONTENTS 1. PLEASE OBSERVE THE FOLLOWING...3 1.1 EMPHASIZED SECTIONS...3 1.2 ITEMS SUPPLIED...3 1.3 FOR YOUR SAFETY...3

More information

EQUIPMENT # OPERATION MANUAL DISPENSING SYSTEM

EQUIPMENT # OPERATION MANUAL DISPENSING SYSTEM EQUIPMENT OPERATION MANUAL #986000 DISPENSING SYSTEM Contents Section Description Page No. 1 Introduction...1 Items Supplied...2 View of Pump-A-Bead II with components labeled...3 2 Theory of Operation...4

More information

Operating Manual High Viscosity Dispense Valve Item #

Operating Manual High Viscosity Dispense Valve Item # Operating Manual High Viscosity Dispense Valve Item # 984594 CLOSE OPEN Item # 984594 Label # 8901197 Warnings INJECTION HAZARD Spray from the valve, hose leaks, or ruptured components can inject fluid

More information

EQUIPMENT Operation Manual. Loctite DuraPump Meter Mix System Part Numbers

EQUIPMENT Operation Manual. Loctite DuraPump Meter Mix System Part Numbers EQUIPMENT Operation Manual Loctite DuraPump Meter Mix System Part Numbers 1041648 1041647 1041643 1041636 1041641 1041620 1041637 1041633 Table of Contents 1 Please Observe the Following 4 1.1 Emphasized

More information

7760A. EQUIPMENT Operation Manual. Loctite Zeta 7760A UV Curing Wand System Part Number: Exposure Time. Timed. Manual. Lamp Hours.

7760A. EQUIPMENT Operation Manual. Loctite Zeta 7760A UV Curing Wand System Part Number: Exposure Time. Timed. Manual. Lamp Hours. EQUIPMENT Operation Manual Timed 7760A Exposure Time TIMER LT4H RESET UP Manual N LOCK is DOWN UV Warning: UV Energy is transmitted from the end of the light guide. Protective eyewear equipped with side

More information

WORLDWIDE EQUIPMENT. Hand-held Applicator OPERATION MANUAL GLOBAL AVAILABILITY GLOBAL SERVICE

WORLDWIDE EQUIPMENT. Hand-held Applicator OPERATION MANUAL GLOBAL AVAILABILITY GLOBAL SERVICE WORLDWIDE EQUIPMENT OPERATION MANUAL Hand-held Applicator 97111 97112 97116 GLOBAL AVAILABILITY GLOBAL SERVICE HAND-HELD APPLICATOR 97111/97112/97116 AN INTEGRATION OF ADHESIVE AND EQUIPMENT TECHNOLOGY

More information

EQUIPMENT OPERATION MANUAL. Loctite Hysol Wheel Coater

EQUIPMENT OPERATION MANUAL. Loctite Hysol Wheel Coater EQUIPMENT OPERATION MANUAL Loctite Hysol Wheel Coater 98038 Contents Page No. 1 Please observe the following...................................... 1 1.1 Emphasized Sections.............................................

More information

Techcon Systems TS500R-PC Controller For Positive Displacement PC Pump

Techcon Systems TS500R-PC Controller For Positive Displacement PC Pump Techcon Systems TS500R-PC Controller For Positive Displacement PC Pump Copyright OK International CONTENTS Page Number 1. Safety 3 2. Symbol Definitions.. 3 3. Specifications... 4 4. Features.. 5 5. Setup

More information

EQUIPMENT Operation Manual. Posi-Link Coupled Cylinder Assembly. Item No Posi-Link Controller P/N:

EQUIPMENT Operation Manual. Posi-Link Coupled Cylinder Assembly. Item No Posi-Link Controller P/N: Program Mode Enter Exit Select Adhesive Pkg Dose Size Input Teach Posi-Link Controller P/N: 98377 Rate Dispense Suck Back Delay Enter Engage New Package Home Unload Stop Dispense Run Mode Auto Manual Select

More information

EQUIPMENT. Loctite Series 9000 Rotospray System OPERATION MANUAL. Pump Reservoir Head PRODUCT RESERVOIR

EQUIPMENT. Loctite Series 9000 Rotospray System OPERATION MANUAL. Pump Reservoir Head PRODUCT RESERVOIR EQUIPMENT OPERATION MANUAL PRODUCT RESERVOIR FULL ADD 1 LITER Loctite Series 9000 Rotospray System ADD 2 LITERS ADD 3 LITERS BEAD OF LOCTITE PRODUCT DISPENSED BY NON-CONTACT MEANS INSIDE A BORE. Pump 983330

More information

HR-20P Pneumatically Controlled Pressure Regulator

HR-20P Pneumatically Controlled Pressure Regulator HR-20P Pneumatically Controlled Pressure Regulator Instruction and Service Manual Hydroplex Corporation 230 West Gloria Switch Rd. Lafayette, LA 70507 337-233-0626 www.hydroplexpumps.com I. General Instructions

More information

EQUIPMENT Operation Manual. Loctite DuraPump Meter Mix System Part Numbers

EQUIPMENT Operation Manual. Loctite DuraPump Meter Mix System Part Numbers EQUIPMENT Operation Manual Loctite DuraPump Meter Mix System Part Numbers 1041649 1041644 1041639 1041638 1041635 Table of Contents 1 Please Observe the Following 3 1.1 Emphasized Sections 3 1.2 For Your

More information

Operating Manual. VoluDrop Dispenser UV

Operating Manual. VoluDrop Dispenser UV Operating Manual VoluDrop Dispenser UV 97650 Contents English...3-16 2 Contents 1 Please observe the following...4 1.1 Emphasized Sections...4 1.2 Items Supplied...4 1.3 For Your Safety...5 1.4 Field of

More information

CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"

CLEAN ROOM DEVICES, LLC WHERE TUBING AND FITTINGS COME TOGETHER CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.1 LAST EDITED 7.25.14 DOCUMENT NUMBER 001 cleanroomdevices.com 1 Table of

More information

CRD610 Automatic Fitting Inserter

CRD610 Automatic Fitting Inserter CRD610 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 1.2 LAST EDITED 12.12.2018 cleanroomdevices.com 1 Table of Contents Title Page. 1 Table of Contents...2 1.0 General Product & Safety Information....3

More information

Users Guide for Ac-sync

Users Guide for Ac-sync Problem solved. Users Guide for Ac-sync Thank you for choosing Anywhere Cart! The AC-SYNC is designed to sync, charge and store 1-36 ipads or tablets. Adjustable device divider bays allow fitment of any

More information

INSTRUCTION MANUAL INSTALLATION, OPERATION, AND MAINTENANCE ACTUATOR MANIFOLD

INSTRUCTION MANUAL INSTALLATION, OPERATION, AND MAINTENANCE ACTUATOR MANIFOLD INSTRUCTION MANUAL INSTALLATION, OPERATION, AND MAINTENANCE B-3724M ACTUATOR MANIFOLD MIDLAND MANUFACTURING CORP. 7733 Gross Point Road Skokie, Illinois 60077 Phone (847) 677-0333 FAX (847) 677-0138 WEBSITE

More information

CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"

CLEAN ROOM DEVICES, LLC WHERE TUBING AND FITTINGS COME TOGETHER CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD600AF Automatic Fitting Inserter With Auto Feed OPERATIONS MANUAL (Shown with optional alcohol dispenser) 1 VERSION 1.1 LAST EDITED

More information

CRD600 Automatic Fitting Inserter

CRD600 Automatic Fitting Inserter CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.3 LAST EDITED 12.07.2018 cleanroomdevices.com 1 Table of Contents Title Page.. 1 Table of Contents. 2 1.0 General Product & Safety Information...3

More information

VP-4124/VP-4124-E 24/48 VOLT DC SWITCHING POWER SUPPLY

VP-4124/VP-4124-E 24/48 VOLT DC SWITCHING POWER SUPPLY Issue 5 24/48 VOLT DC SWITCHING POWER SUPPLY INTRODUCTION These instructions provide the specifications, installation and maintenance information for the VP-4124 and VP-4124-E, 24/48 Volt Power Supplies.

More information

Model NTX7 Series Automatic Battery Charger User s Manual Rev. 1.0 October 17, 2006

Model NTX7 Series Automatic Battery Charger User s Manual Rev. 1.0 October 17, 2006 B R A N D Model NTX7 Series Automatic Battery Charger User s Manual Rev. 1.0 October 17, 2006 For Sales, Support and Service phone: 407-331-4793 fax: 407-331-4708 website: www.xenotronix.com email: information@xenotronix.com

More information

Broadband PowerShield. CP27U Models. User Manual

Broadband PowerShield. CP27U Models. User Manual Broadband PowerShield CP27U Models User Manual 990-2366C 04/2016 Chapter 1: General Information The PowerShield provides a power source for broadband telephony, Fiber-to-the-Home/Premise (FTTH/P), and

More information

Installation Guide. Marine Filter SURT023M SURT024M

Installation Guide. Marine Filter SURT023M SURT024M Installation Guide Marine SURT023M SURT024M suo0738a Product Description The APC by Schneider Electric Marine Application reduces the EMI (electro magnetic interference), produced by a connected that

More information

Manufacturing Facility is ISO9001:2000. Welded Steel Pipe Conform to ASTM A53. Threads Conform to ASME B1.20.1

Manufacturing Facility is ISO9001:2000. Welded Steel Pipe Conform to ASTM A53. Threads Conform to ASME B1.20.1 STEEL NIPPLES S40 & S80 Steel Nipple Product Specifications Manufacturing Facility is ISO9001:2000 Welded Steel Pipe Conform to ASTM A53 Threads Conform to ASME B1.20.1 800-678-2544 800-678-0857 www.msi-products.com

More information

ValveMate 7000 Controller Operating Manual

ValveMate 7000 Controller Operating Manual A NORDSON COMPANY ValveMate 7000 Controller Operating Manual Steady Test Clear Time Set Fast Slow POWER RUN SETUP CYCLE A NORDSON COMPANY VALVEMATE 7000 Run Setup Purge Program Fast Slow Time Set Pressure

More information

PVI 1800/PVI Residential/Commercial Grid-Tied Photovoltaic Inverter WARRANTY MANUAL. Subject to Change REV , Solectria Renewables

PVI 1800/PVI Residential/Commercial Grid-Tied Photovoltaic Inverter WARRANTY MANUAL. Subject to Change REV , Solectria Renewables PVI 1800/PVI 2500 WARRANTY MANUAL Residential/Commercial Grid-Tied Photovoltaic Inverter 2009, Solectria Renewables Subject to Change REV 10.09 1 Product Warranty & RMA Policy 1.1 Warranty Policy The Solectria

More information

Web Volume Control Model WV220

Web Volume Control Model WV220 WEB CONTROL PRODUCTS User Manual Web Volume Control Model WV220 1 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject

More information

STAINLESS STEEL FORGED FITTINGS 3000lb 304/304L & 316/316L Forged Stainless Steel Fittings Product Specifications

STAINLESS STEEL FORGED FITTINGS 3000lb 304/304L & 316/316L Forged Stainless Steel Fittings Product Specifications STAINLESS STEEL FORGED FITTINGS 3000lb 304/304L & 316/316L Forged Stainless Steel Fittings Product Specifications Manufactured in ISO9000:2000 Facility Manufactured to ASTM/ASME A182/SA182 Items conform

More information

REDI-LINE. Rugged, Reliable, DC to AC Power Conversion ELECTRIC GENERATORS USER'S GUIDE. KARAM A.L.

REDI-LINE. Rugged, Reliable, DC to AC Power Conversion ELECTRIC GENERATORS USER'S GUIDE. KARAM A.L. REDI-LINE ELECTRIC GENERATORS USER'S GUIDE Rugged, Reliable, DC to AC Power Conversion KARAM A.L. www.alternatorstarter.com 1-888-515-2726 REDI-LINE ELECTRIC GENERATOR MODEL INPUT ACTUAL OUTPUT ACTUAL

More information

CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"

CLEAN ROOM DEVICES, LLC WHERE TUBING AND FITTINGS COME TOGETHER CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD400 Fitting Inserter OPERATIONS MANUAL VERSION 3.1 LAST EDITED 03.08.11 DOCUMENT NUMBER 001 cleanroomdevices.com 1 Table of Contents

More information

MICROMANOMETER ALNOR MODEL AXD610 AIRFLOW INSTRUMENTS MODEL PVM610

MICROMANOMETER ALNOR MODEL AXD610 AIRFLOW INSTRUMENTS MODEL PVM610 MICROMANOMETER ALNOR MODEL AXD610 AIRFLOW INSTRUMENTS MODEL PVM610 OPERATION AND SERVICE MANUAL P/N 1980587, REV F SEPTEMBER 2014 Copyright TSI Incorporated / 2007-2014 / All rights reserved. Address

More information

Presoak & Tire/Engine Cleaner Systems (Air Pump) DU TC_A & DU PS_A

Presoak & Tire/Engine Cleaner Systems (Air Pump) DU TC_A & DU PS_A Presoak & Tire/Engine Cleaner Systems (Air Pump) DU TC_A & DU PS_A Owner s Manual #0795 Customer Number: Model Number: Serial Number: Installation Date: IMPORTANT Please read and u n d e r s t a n d t

More information

SPC-PANEL Simplex, Single Phase Pump Control Panel

SPC-PANEL Simplex, Single Phase Pump Control Panel Pump Installation and Service Manual SPC-PANEL Simplex, Single Phase Pump Control Panel Pump Controls for 2 HP Grinder Pumps NOTE! To the installer: Please make sure you provide this manual to the owner

More information

Level Alert Model Multi-Switch Liquid Level Sensor. Assembly and Installation Instructions

Level Alert Model Multi-Switch Liquid Level Sensor. Assembly and Installation Instructions Level Alert Model 2000 Multi-Switch Liquid Level Sensor Assembly and Installation Instructions Kit Form Each unit is provided in kit form with step-by-step instructions, making it extremely easy to custom

More information

VP-6124/VP-6124-E 24 VOLT DC SWITCHING POWER SUPPLY

VP-6124/VP-6124-E 24 VOLT DC SWITCHING POWER SUPPLY Issue 6 VP-6124/VP-6124-E 24 VOLT DC SWITCHING POWER SUPPLY INTRODUCTION These instructions provide the specifications, installation and maintenance information for the VP-6124 and VP-6124-E, 24Volt Power

More information

Operating Instructions & Parts Manual. Oil Control Gun. Models 48UJ82, 48UJ83, 48UJ84, 48UJ85 and 48UJ86

Operating Instructions & Parts Manual. Oil Control Gun. Models 48UJ82, 48UJ83, 48UJ84, 48UJ85 and 48UJ86 Operating Instructions & Parts Manual EN Oil Control Gun Models 48UJ82, 48UJ83, 48UJ84, 48UJ85 and 48UJ86 PLEASE READ AND SAVE THESE INSTRUCTIONS. READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL,

More information

Adjustable Angled Incline Conveyor Owners Manual with Operating Instructions

Adjustable Angled Incline Conveyor Owners Manual with Operating Instructions Adjustable Angled Incline Conveyor Owners Manual with Operating Instructions Revision 012211 Table of Contents Basic Conveyor Features 3 Getting Started 4 Setting Up the Incline Conveyor 5 Belt Removal

More information

NEUTRALIZATION SYSTEM FOR OPA & GLUTARALDEHYDE MEDI-NEWT. User Manual. Endoscope reprocessing the the way way it it should be be

NEUTRALIZATION SYSTEM FOR OPA & GLUTARALDEHYDE MEDI-NEWT. User Manual. Endoscope reprocessing the the way way it it should be be NEUTRALIZATION SYSTEM FOR OPA & GLUTARALDEHYDE MEDI-NEWT User Manual Endoscope reprocessing the the way way it it should be be 1 Medi-Newt Neutralization System Instruction Manual 50096-951 Rev C 2011,

More information

Digital Clock model 75100C

Digital Clock model 75100C Instruction Manual Digital Clock model 75100C CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits... 3 Clock Setup... 4 Set the Time & Date... 5 Care

More information

PVI 60KW, PVI 82KW, PVI 95KW

PVI 60KW, PVI 82KW, PVI 95KW PVI 60KW PVI 82KW PVI 95KW WARRANTY MANUAL Commercial, Grid-Tied Photovoltaic Inverters 2008, Solectria Renewables LLC Subject to Change DOC-020099 rev 024 1 1 Product Warranty & RMA Policy Warranty Policy

More information

Straight-Bore Clutch LSCC-32, 44, 54

Straight-Bore Clutch LSCC-32, 44, 54 Straight-Bore Clutch LSCC-32, 44, 54 1 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject to change without notice. Technical

More information

"WHERE TUBING AND FITTINGS COME TOGETHER"

WHERE TUBING AND FITTINGS COME TOGETHER CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD200SS TUBE EXPANDER OPERATIONS MANUAL VERSION 4.3 LAST EDITED 06.17.15 cleanroomdevices.com Table of Contents Table of Contents....1

More information

AIR VELOCITY METER ALNOR MODEL AVM410 AIRFLOW INSTRUMENTS MODEL TA410

AIR VELOCITY METER ALNOR MODEL AVM410 AIRFLOW INSTRUMENTS MODEL TA410 AIR VELOCITY METER ALNOR MODEL AVM410 AIRFLOW INSTRUMENTS MODEL TA410 OPERATION AND SERVICE MANUAL P/N 1980575, REV F FEBRUARY 2016 Copyright TSI Incorporated / 2007-2016 / All rights reserved. Address

More information

Parts Manual. Spray Gun Series Master II. Issue /09/2017 Ref. NR ENG

Parts Manual. Spray Gun Series Master II. Issue /09/2017 Ref. NR ENG Spray Gun Series Master II Issue 3.2 27/09/2017 Ref. NR-00020-ENG Before starting or carrying out maintenance work on the MASTER II gun, please carefully read all the technical and safety documentation

More information

SUNC3000 / Item #40885

SUNC3000 / Item #40885 SUNC3000 / Item #40885 AUTOMATIC POOL COVER PUMP OPERATIONS MANUAL WWW.SUNRUNNERPOOL.COM 1 . Performance GPH of Water @ Total Feet Of Lift MODEL HP Max. Lift 0 ft. 5 ft. 10 ft. 15 ft. 20 ft. SUNC3000 1/3

More information

Motorized Stainless 2-Way Valves

Motorized Stainless 2-Way Valves Installation and Operation Manual Motorized Stainless 2-Way Valves Safety Valve ETV Applications WARNING This Heat-Timer valve is strictly an operating valve; it should never be used as a primary limit

More information

IAQ-CALC INDOOR AIR QUALITY METER MODEL 7515

IAQ-CALC INDOOR AIR QUALITY METER MODEL 7515 IAQ-CALC INDOOR AIR QUALITY METER MODEL 7515 OPERATION AND SERVICE MANUAL P/N 1980571, REVISION D FEBRUARY 2016 Copyright TSI Incorporated / May 2007-2016 / All rights reserved. Address TSI Incorporated

More information

Automated I.V. Stand Cat. No OPERATOR S MANUAL. Operation& Maintenance Instructions. Raising the Standard of Care!

Automated I.V. Stand Cat. No OPERATOR S MANUAL. Operation& Maintenance Instructions. Raising the Standard of Care! Automated I.V. Stand Cat. No. 741314 OPERATOR S MANUAL Operation& Maintenance Instructions Raising the Standard of Care! Table of Contents Warranty....................... 2 Hardware.......................

More information

Container Fountain Kit with LED Light

Container Fountain Kit with LED Light Container Fountain Kit with LED Light REMINDER CALL 1-888-755-6750 BEFORE RETURNING TO STORE. PACKAGE CONTENTS Questions, problems, missing parts? Before returning to your retailer, call our customer service

More information

MV Series Motors Operation & Parts Manual. Models M3V, M5V, M5V-US

MV Series Motors Operation & Parts Manual. Models M3V, M5V, M5V-US MV Series Motors Operation & Parts Manual Models M3V, M5V, M5V-US Introduction This manual pertains to drum pump motors MV Series. Finish Thompson, Inc. thanks you for choosing our products. We believe

More information

Dispenser & Warmer RIC-1909 RIC-1909EXP

Dispenser & Warmer RIC-1909 RIC-1909EXP Dispenser & Warmer RIC-1909 RIC-1909EXP Safety Precautions CAUTION This equipment is designed and sold for commercial use only. This equipment is not to be used by the consumer in home use. Do not allow

More information

Operator's Manual. Storage System. Ultrasound Probe Cabinet. Manufactured by:

Operator's Manual. Storage System. Ultrasound Probe Cabinet. Manufactured by: Storage System Ultrasound Probe Cabinet Operator's Manual Manufactured by: CIVCO Medical Solutions 102 First Street South Kalona, IA 52247 USA 319.248.6757 / 800.445.6741 WWW.CIVCO.COM Copyright 2018 All

More information

DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L

DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L Thank you for purchasing DigiGauge by ZAETECH Disclaimer DigiGauge is for show and off road use only. By using this

More information

OPERATING MANUAL: L/S VARIABLE-SPEED MODULAR DRIVES Model Nos. Pump Drive 07559-00 with Pump Head 07516-00 07559-00 07559-05 07559-10 07559-15 A-1299-7331 Edition 01 (US & Canada only) Toll Free 1-800-MASTERFLEX

More information

Proportioning Unit evolution G-125 A / G-200 A

Proportioning Unit evolution G-125 A / G-200 A Proportioning Unit evolution G-125 A / G-200 A Issue 4.2 20/05/13 Ref. NR-00007-ENG Before installing the unit and starting it up, carefully read all the technical and safety documentation included in

More information

Installation Power Management Unit Battery Cables and Battery Harness

Installation Power Management Unit Battery Cables and Battery Harness Installation Power Management Unit Battery Cables and Battery Harness Important Safety Messages SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during installation

More information

ODY-19-1 AIR PRESSURE GAUGE

ODY-19-1 AIR PRESSURE GAUGE ODY-19-1 AIR PRESSURE GAUGE Introduction: The Odyssey gauge series from Dakota Digital, Inc. incorporates the reliability and quality of our standard gauges, along with several unique features and easy

More information

RENA AF371Feeder Operating Manual. Feeder. Operating Manual. Manual Part #: M AF371 Operations Rev

RENA AF371Feeder Operating Manual. Feeder. Operating Manual. Manual Part #: M AF371 Operations Rev Manual Part #: M-3022 Feeder AF371 Operations Rev. 3-16-04 1 RENA AF371 Feeder YOUR RENA AF371 IS DISTRIBUTED BY RENA SYSTEMS INC. SERVICE AND SUPPORT FOR THIS PRODUCT IS PROVIDED BY YOUR RENA DEALER.

More information

General Installation Instructions for Valves and Gates

General Installation Instructions for Valves and Gates General Installation Instructions for Valves and Gates Thank you for your purchase of a Lorenz valve. We appreciate your business! Please read this installation manual and follow recommended safety precautions.

More information

Techcon Systems TS6500 CIM Automatic Techkit Mixer

Techcon Systems TS6500 CIM Automatic Techkit Mixer Techcon Systems TS6500 CIM Automatic Techkit Mixer User Guide English Copyright OK International 7000-2860_F 1 CONTENTS Page Number 1. Safety..3 2. Unpacking and Inspection.3 3. Description 4 4. Symbol

More information

Installation & Operators Manual

Installation & Operators Manual Installation & Operators Manual Model Serial Number Purchase Date 2007-2008 SegVator, LLC Patent Pending All Rights Reserved Important Safety Information Make sure the vehicle has a properly installed

More information

4V130P-430P SERIES AIR PILOT VALVE

4V130P-430P SERIES AIR PILOT VALVE 4V130P-430P SERIES AIR PILOT VALVE Valve Model 4V130P-1/8 4V230P-1/4 4V330P-3/8 4V430P-1/2 Port & Mounting Action & Motion Operating Pressure Body Ported Double Solenoid, Spool Design, 3 Position, Pressure

More information

SOLUTION DISTRIBUTORS BOOK NO. IM AA UA

SOLUTION DISTRIBUTORS BOOK NO. IM AA UA SOLUTION DISTRIBUTORS BOOK NO. IM 50.320AA UA ISSUE A EQUIPMENT SERIAL NO. DATE OF START-UP START-UP BY Prompt service available from nationwide authorized service contractors. ORDERING INFORMATION In

More information

SUNC1200 / ITEM #40882 SUBMERSIBLE UTILITY PUMP OPERATIONS MANUAL

SUNC1200 / ITEM #40882 SUBMERSIBLE UTILITY PUMP OPERATIONS MANUAL SUNC1200 / ITEM #40882 SUBMERSIBLE UTILITY PUMP OPERATIONS MANUAL WWW.SUNRUNNERPOOL.COM Performance Model HP GPH of Water @ Total Feet Of Lift 0 ft. 5 ft. 10 ft. 15 ft. 20 ft. 25 ft. Max. Lift SUNC1200

More information

PreSoak System (NonFoaming) DU PS1-HP DU PS6-HP

PreSoak System (NonFoaming) DU PS1-HP DU PS6-HP PreSoak System (NonFoaming) DU PS1-HP DU PS6-HP Serial Number: Owner s Manual #0786 040810 Installation Date: Please read and u n d e r s t a n d t h i s manual. Store in safe location for future reference.

More information

Benchmark HD Series Heavy Duty Bench Scale. Installation Manual

Benchmark HD Series Heavy Duty Bench Scale. Installation Manual Benchmark HD Series Heavy Duty Bench Scale Installation Manual 93631 Contents 1.0 Introduction... 1 1.1 Benchmark HD Specifications...................................................... 1 2.0 Installation...

More information

Model P-40 & Model P-25 POWER PUSHER

Model P-40 & Model P-25 POWER PUSHER Power Pusher Description INSTRUCTION MANUAL The Power Pusher provides ram capability by using the spreading power of the POWER HAWK P-16 Rescue Tool. (The Power Pusher may also be used with other spreader

More information

Deflection Sensor Installation Guide for welded steer axles Air-Weigh Customer Support:

Deflection Sensor Installation Guide for welded steer axles Air-Weigh Customer Support: PN:901-0146-003 R0 Deflection Sensor Installation Guide for welded steer axles Air-Weigh Customer Support: 888-459-3247 Steer Axle Deflection Sensors See the manuals included with your kit for complete

More information

n Operator s Manual n Redundant Control Unit FOR CFR UNINTERRUPTIBLE POWER SUPPLIES FROM ALPHA TECHNOLOGIES

n Operator s Manual n Redundant Control Unit FOR CFR UNINTERRUPTIBLE POWER SUPPLIES FROM ALPHA TECHNOLOGIES n Operator s Manual n Redundant Control Unit FOR CFR UNINTERRUPTIBLE POWER SUPPLIES FROM ALPHA TECHNOLOGIES TABLE OF CONTENTS 1. Introduction...1 1.1 The Alpha Redundant Control Unit (RCU)... 1 1.2 A Tour

More information