To Protect Your Warranty, Use Only ENERPAC Hydraulic Oil.

Transcription

1 Repair Parts Sheet POWERFUL SOLUTIONS. GLOBAL FORCE. Pow r Riser Lifting Jacks PR Series Ton Air Models L547 Rev. D 0/16 For Date Codes Beginning with the Letter A To Protect Your Warranty, Use Only ENERPAC Hydraulic Oil. Enerpac recommends that all kit components be installed to insure optimum performance of the repaired product. Note: This illustration is for reference only. The appearance of your unit may differ from the unit shown. P.R. Basic Assembly See Figure Cylinder Assembly See Figure 15 Filter/Lube Assemblies See Figures and Valve Sub-assemblies See Figures 16 through 0 Handle Assembly See Figure 5 Pump Sub-assemblies and Sub-components See Figures 4 through 1 Jack Components See Figures 1 and Manifold Assembly See Figure 1 Pendant Assembly (Not Shown - PRASA Models Only) See Figure 4

2 A RAISE LOWER THIS JACK IS FOR LIFTING ONLY! SUPPORT THE LOAD IMMEDIATELY AFTER LIFT BY OTHER APPROPRIATE MEANS. NEVER GET ON OR UNDER A LOAD SUPPORTED ONLY BY THE JACK. NEVER EXCEED THE RATED CAPACITY OF THE JACK. USE JACK ONLY ON SOLID SURFACES CAPABLE OF SUPPORTING THE LOAD AND THE BASE OF THE JACK. ALWAYS CENTER THE LOAD ON THE LIFTING SADDLE OF THE JACK. USE ONLY ENERPAC HYDRAULIC OIL, OR APPROVED EQUIVALENT. FAILURE TO HEED THESE WARNINGS MAY CAUSE LOSS OF LOAD OR FAILURE OF THE JACK RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY. CONSULT ENERPAC OPERATING INSTRUCTIONS AND ASME/ANSI B0.1 SAFETY STANDARD FOR ADDITIONAL INSTRUCTIONS ABOUT SAFE OPERATION. DO NOT REMOVE OR COVER THIS LABEL MOISTURE IN AIR LINE CAN CAUSE DANGEROUS ICING IN MUFFLER AND BLOW OUT FELT MUFFLER PADDING. USE ONLY ANTI-FREEZE LUBRICANT IN OILER AND MUFFLER E 899E Figure 1 - Main Assembly, PRAMA Models NOTE: This illustration is for reference only. The appearance of your unit may differ from unit shown Testing Procedure: Load the jack to 100 Tons, hold and check. No drift allowed. Lift 1 minute. Lower and check load holding.1" drift max. before load lock off. 100 TON CAPACITY 19 CAUTION 5 VIEW A-A 75 IN-LBS IN-LBS 150 IN-LBS A A 100 TONS 100 NS APPLY LOCTITE IN-LBS IN-LBS

3 Item Repair Parts List (Refer to figure 1) Model Qty. Description PRAMA10016L PRAMA1007L 1 (See Fig. ) (See Fig. ) 1 PR Basic Asm (See Fig. 4A & 4B) (See Fig. 4A & 4B) 1 Subassy, Pump and Air Motor E 40085E 1 Male Elbow /8-/8" 5 408E 408E 1 Load Cap PR Long Stm E 41944E Tire/Rim Assembly E 41779E 1 Air Tubing E 8874E 1 Plug Hex O-Ring 9 (See Fig. 5) (See Fig. 5) 1 Handle Assembly E 85469E 1 Gasket 11 (See Fig. ) (See Fig. ) 1 Filter Lube/Regulator Asm 1 401E Square Hole Plug PR E 8644E 1 Street Elbow E 451E 1 Label 100 Ton Capacity E Lifting Bar 4" PR E 4441E 1 Model Label E Nut Plt - Lift Bar E 899E 1 Decal, Warning PWR R 0 B005046E B005046E 1 Screw 1/4-0 x /4" St E 4605E 1"-8 Hex Lock Nut 6964E 6964E 1 Breather Vent E 441E 1 Tube 5 46E HCS 5/16-18 x 1.5" Plt E Lock Washer 5/16" E 4198E 1 Screw Shoulder E 89967E 1 Enerpac Logo - Large 9 B007046E B007046E Washer Hd. Screw 1/-0 x /4" 8607E 8607E 1 Control Valve Plate 41598E 41598E 1 Lower Weldment 4" PR E 8469E SHC /8-16 x 1.75" E 88111E 1 Label, Caution, Filter/Lube E 4659E Decal Overlay E 41945E Spacer N/A = Not Available.

4 THIS JACK IS FOR LIFTING ONLY! SUPPORT THE LOAD IMMEDIATELY AFTER LIFT BY OTHER APPROPRIATE MEANS. NEVER GET ON OR UNDER A LOAD SUPPORTED ONLY BY THE JACK. NEVER EXCEED THE RATED CAPACITY OF THE JACK. USE JACK ONLY ON SOLID SURFACES CAPABLE OF SUPPORTING THE LOAD AND THE BASE OF THE JACK. ALWAYS CENTER THE LOAD ON THE LIFTING SADDLE OF THE JACK. USE ONLY ENERPAC HYDRAULIC OIL, OR APPROVED EQUIVALENT. FAILURE TO HEED THESE WARNINGS MAY CAUSE LOSS OF LOAD OR FAILURE OF THE JACK RESULTING IN PROPERTY DAMAGE OR PERSONAL INJURY. CONSULT ENERPAC OPERATING INSTRUCTIONS AND ASME/ANSI B0.1 SAFETY STANDARD FOR ADDITIONAL INSTRUCTIONS ABOUT SAFE OPERATION. DO NOT REMOVE OR COVER THIS LABEL MOISTURE IN AIR LINE CAN CAUSE DANGEROUS ICING IN MUFFLER AND BLOW OUT FELT MUFFLER PADDING. USE ONLY ANTI-FREEZE LUBRICANT IN OILER AND MUFFLER E 899E Figure - Main Assembly, Pendant Controlled PRASA Models NOTE: This illustration is for reference only. The appearance of your unit may differ from unit shown Testing Procedure: Load the jack to 100 Tons, hold and check. No drift allowed. Lift 1 minute. Lower and check load holding.1" drift max. before load lock off. 100 TON CAPACITY CAUTION VIEW B-B A IN-LBS B B TONS 100 TONS A 9 P IN-LBS INSTALL IN LOWER PORT OF VALVE APPLY LOCTITE IN-LBS IN-LBS IN-LBS 4

5 Repair Parts List (Refer to figure ) Item Model PRASA10016L PRASA1007L Qty. Description 1 (See Fig. ) (See Fig. ) 1 PR Basic Asm (See Fig. 5A & 5B) (See Fig. 5A & 5B) 1 Subasy, Pump and Air Motor 40085E 40085E 1 Male Elbow /8-/8" 5 408E 408E 1 Load Cap PR Long Stm E 41944E Tire/Rim Assembly E 41779E 1 Air Tubing E 8874E 1 Plug Hex O-Ring 9 (See Fig. 5) (See Fig. 5) 1 Handle Assembly E 85469E 1 Gasket 11 (See Fig. ) (See Fig. ) 1 Filter Lube/Regulator Asm 1 401E Square Hole Plug PR 1 864E 864E 1 Male Elbow E 4444E 1 Decal, Blank 15 (See Fig. 4) (See Fig. 4) 1 Pendant, Air E 451E 1 Label 100 Ton Capacity E 41965E 1 Hose E 899E 1 Decal, Warning PWR R 0 B005046E B005046E 1 Screw 1/4-0 x /4" St E 4605E 1"-8 Hex Lock Nut 6964E 6964E 1 Breather Vent E 1 Hanger, 10" Lock Ring E 4 SHCS, #10- x 1/" SS E 4 Lockwasher, #10 7 B007046E B007046E Washer Hd. Screw 1/4-0 x /4" E 4968E Swivel Tee, 1/8" 9 DS DS Control Valve, Air E 45970E 1 Nipple, Male 1/4" x 1/8" E 441E 1 Tube 458E Lifting Bar 4" PR 465E Nut Plt - Lift Bar 4 46E HHCS 5/16-18 x 1.5" Plt E Lock Washer 5/16" E 4198E 1 Screw Shoulder E 89967E 1 Enerpac Logo - Large 9 467E 467E 1 S-Hook, Pendant E 4445E 1 Shuttle Valve E 4099E 1 Hose, /16" 10.5" Lg E 4098E 1 Hose, /16" 1.5" Lg E 4667E Reducer, 1/4-1/8" E 4966E 1 Street Elbow, 1/8" E 18970E Swivel, Straight, 1/" E 4967E 1 Street Elbow, 1/4", 90 Deg E 41598E 1 Lower Weldment 4" PR E 8469E SHC /8-16 x 1.75" E 88111E 1 Label, Caution, Filter/Lube E 4659E Decal Overlay E 41945E Spacer N/A = Not Available. 5

6 Figure SR, 4408SR Pow r Riser Basic Assembly FT. LBS TORQUE BOLTS TO 5 FT-LBS. MINIMUM TORQUE ADAPTER TO 180 FT-LBS. MINIMUM 6 TORQUE ACORN NUT TO FT-LBS

7 Repair Parts List (Refer to figure ) Model Item PRAMA10016L and PRASA10016L PRAMA1007L and PRASA1007L Qty. Description BASIC ASSY 4199SR 4408SR E 41886E 1 Housing Mach P. R. 4 (See Fig. 15) (See Fig. 15) Ton Cylinder Assy E 85477E Jam Nut 6 (See Fig. 14) (See Fig. 14) 1 O.C. Valve and Hoses E 9947E 6 Lock Washer 5/8" E 9605E 6 SHCS 5/8-11 x 1.5" Lg E 41941E Ton P.R. Base E 89754E 1 Screen - " Nipple E 44968E Rubber Ball /8" E 9950E 1 1/4" Soc Pipe Plug 15 1 Gasket Adapter E 41948E Axle Shaft E 4194E 1 Adapter O.C. Valve E 475E PR Base Pin E 46740E 1 Acorn Nut 5/ E 41940E 1 Ring 100 Ton 1 1 O-Ring 6-/4 x 7-1/4" 1 O-Ring 9" x 9-1/" 1 Gasket Base 4 1 O-Ring Power Riser E 6601E 1 Magnet 7 1 O-Ring 6" x 6-1/4" E 6818E Gasket Plug Included in 54411K Repair Kit. 7

8 Figure 4A SR Pump and Motor Sub-Assembly (PRAMA Models Only) A PUMP ASSEMBLY SPECIFICATIONS: 16 TONNAGE: 100 TONS PRESSURE RELIEF: 9,500-9,700 PSI PRESSURE UNLOADING: 800 PSI 8

9 Repair Parts List (Refer to figures 4A and 4B) Item Part Number Qty. Description SR 1 Pump Asm 4P Air 6601E 1 Gasket-Motor 681E 1 Motor E 1 Valve 5 DD608101E 1 Cover Plate, Reservoir E 1 Air Motor E 1 Pin Dowel / (See Fig. 1) 1 Manifold Asm NPR E 5 SHCS /8-16 x 1-1/" 11 (See Fig. 0) 1 Locking Valve w/relief 1 (See Fig. 16) 1 Control Valve Asm. 1 48E 4 SHCS /8-16 x 8.0" SR 1 Adapter Assy E 1 Nipple, 1/4NPT x 1.5L E 1 Pipe Coupling, 1/4" 17 (See Fig. 1) 1 Filter Block Assembly E 1 Roll Pin 1/8 x /8" Lg E Swivel Fitting 0 DD610607E 1 Valve Gasket 1 B10108X SHCS, 1/4-0 x 1.5" Lg Included in 54177K Repair Kit. Figure 4B SR Pump and Motor Sub-Assembly (PRAMA Models Only)

10 Figure 5A SR Pump and Motor Sub-Assembly (PRASA Models Only) PUMP ASSEMBLY SPECIFICATIONS: TONNAGE: 100 TONS PRESSURE RELIEF: 9,500-9,700 PSI PRESSURE UNLOADING: 800 PSI 10

11 Repair Parts List (Refer to figures 5A and 5B) Item Part Number Qty. Description SR 1 Pump Asm 4P. 6601E 1 Gasket-Motor 681E 1 Motor E 1 Valve 5 DD608101E 1 Cover Plate, Reservoir E 1 Air Motor E 1 Pin Dowel / (See Fig 1) 1 Manifold Asm NPR E 5 SHCS /8-16 x 1-1/" 11 (See Fig 0) 1 Locking Valve w/relief 1 (See Fig 17) 1 Control Valve Asm E 4 SHCS /8-16 x 8.0" SR 1 Adapter Assy E 1 Nipple, 1/4" NPT x 1.5"L E 1 Pipe Coupling, 1/4 17 (See Fig 1) 1 Filter Block Asm E 1 Roll Pin 1/8 x /8" LG E Swivel Fitting 0 DD610607E 1 Valve Gasket 1 B10108X SHCS, 1/4-0 x 1.5" Lg Included in 54177K Repair Kit. Figure 5B SR Pump and Motor Sub-Assembly (PRASA Models Only) 11

12 Figure 6A SR Pump Assembly 180 IN-LBS IN-LBS. 50 IN-LBS. 180 IN-LBS IN-LBS IN-LBS IN-LBS IN-LBS IN-LBS IN-LBS IN-LBS IN-LBS IN-LBS. 5 IN-LBS

13 Repair Parts List (Refer to figures 6A and 6B) Item Part Number Qty. Description Item Part Number Qty. Description E 1 Pump Body 4 Piston E 1 Plate-Bottom 6860E 1 Bearing, Roller E 1 Gearset, /8 Clydesdale 660E 1 Thrust Bearing E 1 Shaft-Idler E Thrust Washer E 1 Screen 5 (See Fig. 9) 1 Eccentric Shaft Assembly 1 689E Tube-Guide E 1 Thrust Bearing 89148E 1 SHCS 1/4-8 x 1-1/" E Thrust Washer 5 685E 1 Spring 8 (See Fig. 7) 1 Adapter-Shaft Asm. 6 81E 1 Roll Pin 1/8 x 15/16" E O-Ring 1-7/8 x " Ure 7 686E 1 Screw, Ball Stop E 1 Retaining Ring E Gasket 5/64 x 19/" E 1 Adaptor.10 Piston E 4 SHCS 1/4-8 x 1-/4" E 1 Piston.10 Dia E 1 Tube Return E 1 Spring, Piston E Shaft Adp Backup Was E 1 Ball Stop E 1 Spring E 1 1/4" Soc Pipe Plug E Bearing 16 (See Fig. 8) 1 Unloading Piston Assy E 1 Ring-Retaining E 1 Ball Retainer 46 A Pipe Plug 1/8" Flush E 5 Ball 1/8" E 1 Seat - Ext Relief E 1 Intake Seat E 1 Cone - Ext Relief SR 1 Tube Asm E 1 Spring - Relief Valve E Ball 5/16" E 1 Relief Valve Adj. Screw 4671E 1 Unloading Spring 5 467E 1 Spring Cap Unload Valve 4674E 1 Set Screw Unloading Valve 5 (See Fig. 10) Piston Blk E 1 Hex Nut Unloading Valve 54 B SHCS E 1/16" Soc Pipe Plug E 6 SHCS 5/16-4 x 5/8" Included in 54177K Repair Kit. Included in 55057K Relief Kit Figure 6B SR Pump Assembly IN-LBS IN-LBS IN-LBS. 1

14 Figure SR Adapt-Shaft Assembly Repair Parts List (Refer to figure 7) Item Part Number Qty. Description E 1 Adapter Shaft 6600E 1 Bearing 68901E 1 Seal Included in Repair Kit 54177K. Figure SR Unloading Piston Assembly Repair Parts List (Refer to figure 8) Item Part Number Qty. Description E 1 Unload Piston E 1 O-Ring 4768E 1 Back-Up Washer E 1 Roll Pin Figure SR Eccentric Shaft Assembly Repair Parts List (Refer to figure 9) Item Part Number Qty. Description E 1 Eccentric Shaft, 7/8" 68818SR 1 Eccentric Asm E Bearing Washer E 1 Retaining Ring E 1 Ball Figure SR Piston Block Assembly IN-LBS IN-LBS IN-LBS IN-LBS. 00 IN-LBS. Repair Parts List (Refer to figure 10) Item Part Number Qty. Description 90906E Ball 1/8" 6604E 1 Spring E 1 Ball Stop E 1 Ball Retainer E 1 Intake Seat E 1 Gasket 9/64 x 5/8" E 1 Plug, Piston Block E 1 Gasket 5/64 x 19/" E 1 Adaptor.10 Piston E 1 Spring, Piston E 1 Piston,.10 Dia SR 1 Adapter Assy E 1 O-Ring /16 x 5/16" 15 A Pipe Plug 1/8" Flush Included in Repair Kit 54177K. 14

15 Figure SR Adapter Assembly Repair Parts List (Refer to figure 11) Item Part Number Qty. Description E 1 Valve Adapter 65881E B-U Ring 56001E O-ring, /8 x 1/" Included in Repair Kit 54177K. Figure SR Eccentric Bearing Assembly Repair Parts List (Refer to figure 1) Item Part Number Qty. Description E 1 Ring, Eccentric 68060E 1 Bearing, Sleeve Figure USR Filter Block Assembly Repair Parts List (Refer to figure 1) Item Part Number Qty. Description E 1 Filter Block 69670E 1 Oil Filter Power Pump 69144E 1 Adapter Filter E 1/4" Soc Pipe Plug E 4 O-Ring 5/16 x 7/16" URE E 1 O-Ring /16 x 5/16" 15

16 Figure 14-45SR OC Valve Subassembly Repair Parts List (Refer to figure 14) Item Part Number Qty. Description Item Part Number Qty. Description 1 695MSR 1 O.C. Valve Asm New PR 5 454E Hose 1/4 x 17" Nw PR 18970E 1 Elbow 1/4" 90 Deg Strt E 1 /8" Pipe Plug - Flush 45E 1 Elbow 1/4-/8" 90 Strt N/S 94414E 1 Ball 7/16" E Gasket-Plug N/S = Not Shown. Figure SR, 440SR Cylinder Assembly Model Repair Parts List (Refer to figure 15) PRA_A10016L (all versions) PRA_A1007L (all versions) Item Asm SR Asm. 440SR Qty. Description E 449E 1 Cylinder Weldment 4191SR 447SR 1 Piston Rod Asm. 4194E 4194E Ton Head Gland 4 1 T-Seal Rod 4" Dia 5 1 T-Seal Piston 5-1/4" 6 1 Wiper 4" Rod Dia 7 1 O-Ring 5" x 5-1/4" 8 1 B-U Washer E 4195E 1 Ring 10 N/A 408E 1 Swivel Eye Bolt 1/" 11 N/A 44888E 1 Washer Eyebolt E 45664E 1 O-Ring Face Seal Plug E 45666E 1 O-Ring Ftg, /8" NPT Included in 54401K Repair Kit. 16

17 Figure SR 4-Way Manual Valve Subassembly (PRAMA Models Only) Repair Parts List (Refer to figure 16) Item Part Number Qty. Description Item Part Number Qty. Description 1 476E 1 Valve Rotor E 1 Seal E 4 O-Ring E Spring Washer 68180E 1 Subplate - Valve E 1 Detent Spring E 1 O-Ring E 1 Ball E Thrust Washer E 1 Valve Handle E 1 Thrust Bearing E 1 Screw E 1 O-Ring E Screw E 1 Upper Valve Block E 4 Screw E 1 Drive Lok Pin E 1 O-Ring E O-Ring E Seal E Washer Y E 1 Lockwasher Included in Valve Kit 54490K. 17

18 Figure SR P4WM Air Valve Assembly (PRASA Models Only) Repair Parts List (Refer to figure 17) Item Part Number Qty. Description Item Part Number Qty. Description 1 (See Fig. 18) 1 Valve Assembly TC E Spring (See Fig. 19) Air Cyl Assembly E 4 O-Ring 5/16 x 7/16" 6888E 1 Cover, Valve E 4 Screw E 1 Gasket Cover E 8 SHCS #10-4 x.5" Figure SR Valve Assembly TC (PRASA Models Only) IN*LBS IN-LBS IN-LBS Repair Parts List (Refer to figure 18) Item Part Number Qty. Description E 1 Body-Valve 68709E 1 Slider 90548E 1 Ball E 1 Screw E O-Ring E Back-up Washer 8 688E Seal E Spring E 1 O-Ring E 4 Bearing, Roller E Pin Bearing E 1 Set Screw, 5/16-18 x 1/4" E Screw E 1 Plate-Top E 1 Ball, 1/4" E 1 O-Ring E Roll Pin 5 IN-LBS

19 Figure SR Air Cylinder Assembly (PRASA Models Only) Repair Parts List (Refer to figure 19) Item Part Number Qty. Description E 1 Body Air Cylinder E 1 O-Ring 1/8-1/4" E 1 O-Ring 1/4-/8" E 1 Air Cylinder Piston E 1 Spring, Air Cylinder E 1 End Cap E 1 O-Ring 1-1/16 x 1-/16" E 1 Seal E 1 O-Rng 11/16 x 1/ E 1 O-Ring SAE Port # E 1 Push Pin Air Valve E 1 Override Pin E 1 E-Ring 1/4" Shaft E 1 Spring Plate Air Valve 19

20 Figure SR Locking Valve Subassembly (with relief) SPOOL AND SEAL REPLACEMENT INFORMATION OLD DESIGN - ITEM A 0.4" 0.8" 0.198" 0.196" DIA. IMPORTANT: Use items B and 4B with NEW design spool, item B. A B A A A B B B 0.9" 0.505" NEW DESIGN - ITEM B 0.10" 0.05" 0.64" 0.6" DIA. IMPORTANT: Use items A and 4A with OLD design spool, item A. 0.07" 0.50" Note: Old design spool (A) must be replaced with new design spool (B) if it is worn or damaged. Old design spool (A) is no longer available. Repair Parts List (Refer to figure 0) Item Part Number Qty. Description Item Part Number Qty. Description 1 407E 1 Locking Valve Body - Relief E 1 Plug SAE #4 A (not available) 1 Spool Piston (old design) E 1 Spring Washer B 477E 1 Spool Piston (new design) E 1 Spring Eyelet Lock A E Backup Washer E 1 Seat - Ext Relief B 497E Backup Washer TEF E 1 Cone - Ext Relief 4A E 1 O-Ring /16 x /8" E 1 Spring - Relief Valve 4B B O-Ring 1/4 x /8" E 1 Relief Valve Adjusting Scr E 1 Seat E 1/16" Pipe Plug - Flush 6 956E 1 Ball 9/" E 1 Screen O.C. Valve E 1 Plug - Adapt P.R. Lock 1 44E 1 Screen O.C. Valve E 1 Gasket - Plug 69517E 1 Screen Cap E O-Ring 1/4 x /8" Ureth 85E 1 Pipe Plug 1/4" Flush E 1 O-Ring 5/8 x /4" Ureth 4 476E 1 Washer PR Lock Block E 1 Compression Spring E 1 Compression Spring Included in 55057K Relief Kit. Included with item B 0

21 Figure SR Manifold Assembly 50 IN-LBS IN-LBS IN-LBS 90 IN-LBS IN-LBS Repair Parts List (Refer to figure 16) Item Part Number Qty. Description Item Part Number Qty. Description E 1 Manifold Pow r Riser E 1 O-Ring Face Seal Plug 40049E 1/16" Pipe Plug - Flush E 1 O-Ring Face Tube Ftg 1/4" 8109E 1 Pipe Plug 1/8" Flush E 1 Nipple 1/4" E 1 Elbow 90 /8-1/4" 1

22 Figure - DS107900SR Filter Lube Assembly (PRAMA Models Only) VIEW A - A SIGHT GLASS TO FACE THIS DIRECTION 4 NOTE ( ): ASSEMBLE WITH LOCTITE 4 Item Repair Parts List (Refer to figure ) Part Number Models PRASA10016L and PRASA1007L Qty. Description 1 DS E 1 Air Filter 864E 1 Air Lubricator 69998E 1 Pipe Nipple E 1 Bracket/Nipple Weldment E 1 Swivel Male 1/" NPTF E 1 Air Valve E 1 Street Elbow

23 Figure - DS SR Filter Lube Assembly (PRASA Models Only) VIEW A - A NOTE ( ): ASSEMBLE WITH LOCTITE 4 SIGHT GLASS TO FACE THIS DIRECTION 4 Item Repair Parts List (Refer to figure ) Part Number Models PRASA10016L and PRASA1007L Qty. Description 1 DS Filter/Regulator 864E 1 Air Lubricator Pipe Nipple 1/" BRS E 1 Bracket/Nipple Weldment E 1 Swivel Male 1/" NPTF E 1 Air Valve 7 478E 1 Male Run Tee 1/" 8 477E 1 Pipe Adpter, 1/-1/8" 9 480E 1 Swivel Adapter, 1/8" E 1 Street Elbow

24 Figure SR Motor Pendant (PRASA Models Only) Repair Parts List (Refer to figure 4) Item Part Number Qty. Description E 1 Pendant Body 41969E 1 Block Air Pendent 4196E Cartridge-Air 4 481E Swivel ADP 1/8" E Ball 5/" E Retaining Ring E Cartridge Cap 4

25 Figure SR Upper Handle Assembly Repair Parts List (Refer to figure 5) Item Part Number Qty. Description Item Part Number Qty. Description E 1 Upper Weldment E 1 Washer 9/16" ID x /" 468E 1 Handle Lock Lever E 1 Roll Pin 5/ x 7/8" E 1 Sleeve E 4 Washer SS 1/4" E 1 Handle Rod 1 440E 4 Pin Ring E 1 Spring. 656 x 9.50" 1 48E Pin Handle Lever E 1 E-Ring.8/.8 x.04 5

26 Enerpac Worldwide Locations internet: Australia and New Zealand Actuant Australia Ltd. P.O. Box 6867 Wetherhill Park, NSW1851 Block V Unit Regents Park Estate 91 Park Road Regents Park NSW 14 Australia T F sales-au@enerpac.com Brazil Power Packer do Brasil Ltda. Rua Luiz Lawrie Reid, Diadema (SP) - Brazil T Toll Free: vendasbrasil@enerpac.com China (Taicang) Actuant (China) Industries Co. Ltd. No. 6 Nanjing East Road, Taicang Economic Dep Zone Jiangsu, China T F Toll Free: sales-cn@enerpac.com France, Switzerland, North Africa and French speaking African countries ENERPAC Une division d ACTUANT France S.A.S. ZA de Courtaboeuf, avenue de la Baltique VILLEBON /YVETTE France T F sales-fr@enerpac.com Germany and Austria ENERPAC GmbH P.O. Box 0011 D Düsseldorf Willstätterstrasse 1 D Düsseldorf, Germany T F sales-de@enerpac.com India ENERPAC Hydraulics (India) Pvt. Ltd. No. 10, Bellary Road, Sadashivanagar, Bangalore, Karnataka India T info@enerpac.co.in Italy ENERPAC S.p.A. Via Canova Corsico (Milano) T F sales-it@enerpac.com Japan Applied Power Japan LTD KK Besshocho 85-7 Kita-ku, Saitama-shi 1-081, Japan T F sales-jp@enerpac.com Middle East, Egypt and Libya ENERPAC Middle East FZE Office 4, LOB 15 P.O. Box 18004, Jebel Ali, Dubai United Arab Emirates T +971 (0) F +971 (0) sales-ua@enerpac.com Russia Rep. office Enerpac Russian Federation Admirala Makarova Street Moscow, Russia T F sales-ru@enerpac.com Southeast Asia, Hong Kong and Taiwan Actuant Asia Pte Ltd. 8 Joo Koon Circle Singapore T F Toll Free: sales-sg@enerpac.com South Korea Actuant Korea Ltd. Ba 717, Shihwa Industrial Complex Jungwang-Dong, Shihung-Shi, Kyunggi-Do Republic of Korea T F sales-kr@enerpac.com Spain and Portugal ENERPAC SPAIN, S.L. Avda. Los Frailes, 40 Nave C & D Pol. Ind. Los Frailes 8814 Daganzo de Arriba (Madrid) Spain T F sales-es@enerpac.com Sweden, Denmark, Norway, Finland and Iceland Enerpac Scandinavia AB Kopparlundsvägen 14, 71 0 Västerås Sweden T +46 (0) scandinavianinquiries@enerpac.com The Netherlands, Belgium, Luxembourg, Central and Eastern Europe, Baltic States, Greece, Turkey and CIS countries ENERPAC B.V. Galvanistraat 115, 6716 AE Ede P.O. Box 8097, 6710 AB Ede The Netherlands T F sales-nl@enerpac.com Enerpac Integrated Solutions B.V. Spinelstraat 15, 7554 TS Hengelo P.O. Box 41, 7550 AK Hengelo The Netherlands T F integratedsolutions@enerpac.com South Africa and other English speaking African countries Enerpac Africa Pty Ltd. No. 5 Bauhinia Avenue Cambridge Office Park Block E Highveld Techno Park Centurion 0157 Republic of South Africa T: sales-za@enerpac.com United Kingdom and Ireland ENERPAC UK Ltd. 5 Coopies Field Morpeth, Northumberland NE61 6JR, England T sales-uk@enerpac.com USA, Latin America and Caribbean ENERPAC World Headquarters P.O. Box 41 Milwaukee WI USA N86 W1500 Westbrook Crossing Menomonee Falls, Wisconsin 5051 T F User inquiries: T Distributor inquiries/orders: T F Technical inquiries: techservices@enerpac.com sales-us@enerpac.com All Enerpac products are guaranteed against defects in workmanship and materials for as long as you own them. For the location of your nearest authorized Enerpac Service Center, visit us at