230 & 3400 Gravity Wagons & Accessories

Transcription

1 OPERATORS MANUAL & PARTS BOOK 230 & 3400 Gravity Wagons & Accessories 1050 E. COLUMBIA P.O. BOX 168 ARTHUR, IL TOLL FREE: PHONE:

2 WARNINGS, INSTRUCTIONS & MAINTENANCE Keep hands, feet, hair and clothing away from moving parts while unit is in operation. Stay away from intake during operation. Never allow anyone in, near or on the gravity box during transporting or unloading grain. Moving grain is dangerous and can cause entrapment, resulting in severe injury or death by suffocation. Do not operate on public roads unless equipped with proper lighting or warning devices. It is the responsibility of the user & owner to install lighting or other equipment as required by state & federal laws. Make sure that the gravity box is properly fastened to the running gear. Do not use side extensions with the 230 gravity box. Only with a 13 ton gear can 14 extensions be added to the 3400 gravity wagon to increase the capacity to 400 bushels. Connect hydraulic power to the 3/8 Pipe Thread valve ports. Reverse connections if necessary for correct rotation of auger. CAUTION: Never try to unplug the auger when under power! Seed damage will be minimized by keeping the auger full of grain & not running it too fast. All sizes of tires should be inflated to approx. 55 PSI. Before first use, then annually, check wheel bearings for sufficient grease & proper adjustment. Regularly grease front spindles, tie rod ends, tongue bolt, steering frame, hand wheel, & pivot shaft. Check wheel nuts for proper torque before first use, after first load, and then periodically. (100 ft/lbs on 872W, 150 ft/lbs on 1074 & 1384B)

3 Model #: Model #: # Description Part # # Description Part # 1 Door w/rack " Pivot Machined Pinion Rack Pivot Shaft Tooth Mach. Pinion Gear Cotter Pin Auger Mate Mounting Angle Ladder Handwheel E-Z Trail Decal " Crossbar Model # Decal Rubber Strap Striping Handwheel Assembly Opt. Extension for 3400, only with 13 Ton Gear 9 Chute " X 12'6" Ext'n Side /8 X 4 Eye Bolt " X 8'6" Ext'n End " Washer " Corner Angle Cross Chain Assembly Bag of Bolts - 3/8 X 3/4 4255

4 Model #: 872W B Model #: 872W B # Description Part # # Description Part # 1 Standard Wheel Rear Axle w/spindles Opt. 22.5X8.25 Wheel /8 X 5 Bolt & Nut Hub Cap E-Z Clamp /4-16 Slotted Nut Square Reach Cotter Pin /4 X 1-3/4 Bolt Spindle Washer Spacer Plate Outer Bearing Front Axle Outer Race Left Front Spindle Wheel Nut Right Front Spindle Wheel Stud Machinery Bushing Grease Zerk Bent Spindle Cap Hub w/races /8 X 1 Bolt Inner Race Steering Spindle Ass'y Inner Bearing /4-16 Flange Nut Grease Seal /4-10 Lock Nut Hub Assembly /4 Flat Washer Stake Pocket Upper Clamp Plate Rear Spindle Decal Set

5 Model #: 872W B Model #: 872W B # Description Part # # Description Part # 36 Tie Rod End Assembly /8-9 Lock Nut Rubber Cover Lock Pin Jam Nut Spring Grease Zerk Latch Pin Slotted Nut Latch Cotter Pin Tongue Outer /8 Lock Washer Tongue Inner /8 Flat Washer /4-10 X 1 Bolt Tie Rod Steer. Frame w/races Seal E-Z Hitch Assembly Steering Frame Brng Cushion E-Z Hitch Assy Steering Frame Race Cushion Inner Assy Washer Cushion Inner Tube /4-16 Slotted Nut Cushion Clevis Hitch Cotter Pin Round Bushing Steering Frame Cap Dowel Pins Spring /8" X 4-3/4" Bolt Tongue Bolt Urethane Cushions

6 # Description Part # # Description Part # # Description Part # 1 1" Bearing Flange Clamp Control Rod Plate Bearing Flange Hopper Side Plate Hopper Replacement Flex w/ Rivets Hopper Rod Winch Cable Assembly ' Auger Tube Cotter Pin /2" X 4" Eye Bolt ' Auger Tube Hyd. Motor for Bolt-on Valve Eye Bolt Support Washer ' Auger Tube Seal Kit for Sq. 4-bolt Motor Transport Bracket ' Auger Screw Seal Kit for Rd. 7-bolt Motor /2" X 1" Set Screw ' Auger Screw U-bolt Transport Cradle ' Auger Screw Clean-out Door " Lock Collar Control Rod Bracket Valve Lever Spout Clamp Pulley Brckt. & Trnsprt. Latch Control Valve, Direct Mount /2" Pulley /2" Pulley & Chain Motor Plate Attachment Cable Assembly Winch Bracket ' Fiberglass Control Rod Holder Clamp Brake Winch ' Fiberglass Control Rod Spring Snap Link Rope & Pulley Kit ' Fiberglass Control Rod 61214

7 For Model #: For Model #: # Description Part # # Description Part # 1 Arched End Cap Crank Holder Bracket Roll Tarp Bow Crank Holder Assembly Center Rod Tarp Stop Latch Plate Tarp Clamp Replacement Tarp Roll Plug Roll Tube Bunge Cord Square Drive Tube Edge Trim U-Joint Eye Bolt Crank Fastening Pipe

8 # Description Part # # Description Part # 1 Keyfob Remote Transmitter Wireless Remote Bracket Remote Receiver Control Rod Plate Linear Actuator U-Bolt Power Cord Installation Instructions: 1. Mount unit to auger approximately 2 from bottom end. 2. Insert the auger control rod thru the square tube in the center of unit. Adjust the unit so it lines up straight with the control rod. 3. Adjust the arm on the control valve out so that it takes a 2-1/4 stroke to go from fully closed to fully open. 4. With the actuator retracted and the control rod pulled up, fasten the actuator rod to the control rod with the U-bolt. 5. Connect power cord to 12 volt DC power source. The smooth insulated wire is +, the ribbed wire is ground. 6. Press button on transmitter and hold until full stroke is completed. Transmitter & receiver are programmed to work together. Should re-programming be needed, follow these instructions: 1. Verify that the DC input power is connected to the receiver. 2. Depress and hold the receiver s LEARN pushbutton switch. After the LEARN LED illuminates, release the switch. 3. Depress and hold any pushbutton on the remote. Verify that the LEARN LED flashes ON and OFF, and then stays ON. This verifies that the receiver has identified the remote being used. 4. After 5-seconds the LEARN LED will extinguish. 5. The system is ready for operation. Depress any switch on the remote to verify the operation..