Leakage rate. Valve body. U.S. Registered Trademark EN0B-0308GE51 R1002 Copyright 2002 Honeywell Inc. All rights reserved

Transcription

1 V5832/58,C SMLL LINER VLVES PN16 FOR MODULTING ND ON/OFFCONTROL V5832 V58 SPECIFICTION DT FETURES Small size allows installation where space is limited Long stroke results in a high quality characteristic Soft seat provides low leakage rate and high rangeability Reduced k VS values in the bypass to facilitate hydronic balancing Range of fittings available for different connections (soldered, threaded) djustment cap for manual operation Flat surfaces on body to fit installation tools Flat sealing connections in standard sizes Valve inserts changeable without draining by using insert replacement tool WV mm distance between ports / and the bypass (V58C, only) V58C GENERL These small linear valves are used in combination with small electric linear valve actuators and thermoelectric actuators for the control of hot and/or chilled water for fan coil units and small reheaters/recoolers in electric/electronic temperature control systems. SPECIFICTIONS Models Operation Nominal pressure rating Twoway V5832 Threeway V58 Threeway with bypass V58C Twoway stem up to open, port to ; Threeway stem up to close, port to PN16 Capacity index (k VS) see tables on page 2 and 3 Leakage rate 0.02% of k VS Valve body Material rass Size DN15 (1/2 ), (3/4 ) Trim Stem Plug Suitable medium Stainless steel rass Controlled water temperature C Water, with max. 50% glycol U.S. Registered Trademark EN00308GE51 R1002 Copyright 2002 Honeywell Inc. ll rights reserved

2 Modulating valves Rangeability Twoway valves 100:1 Threeway valves 100:1 for controlled port Flow characteristic Equal percentage port, linear for bypass port Stroke 6.5 mm On/Off valves Stroke 2.5 mm Dimensions see Fig. 4 on page 5 FLOW CPCITIES ND CLOSE OFF PRESSURE RTINGS TWOWY VLVES Valve DN k VS Order number M6410C,L/M7410C,E (180 N) CloseOff Pressure (kpa) with ctuators M4450/M8450 (90 N) Z100/M7410 (90 N) V V V V V V V * 20 V * 15 V ** V ** * 50* *Up to 1000kPa system pressure. **For on/off control, stroke 2.5mm. THREEWY VLVES Valve CloseOff Pressure (kpa) with ctuators DN k VS k VS M6410C,L/M7410C,E M4450/M8450 Z100/M7410 Order Number (180 N) (90 N) (90 N) V V V V V V V V V V584007* V584015* *For on/off control, stroke 2.5mm. EN00308GE51 R1002 2

3 THREEWY VLVES WITH YPSS Valve CloseOff Pressure (kpa) with ctuators DN k VS k VS M6410C,L/M7410C,E M4450/M8450 Z100/M7410 Order Number (180 N) (90 N) (90 N) V58C V58C V58C V58C V58C V58C V58C V58C V58C V58C4003* V58C4011* *For on/off control, stroke 2.5mm. OPERTION builtin return spring in the twoway valve produces an opening force. In the threeway valve and the threeway valve with bypass, the spring produces a closing force on the to ports. The valves are supplied with a screwedon adjustment cap for manual operation and for protection of the stem. This allows the stem to be set up for filling or initial heating/cooling during the building construction phase without the use of a controller or actuator. The small electric valve actuators as well as the thermoelectric actuators provide automatic control over the opening and closing movement of the valve stem. TYPICL OPERTION ll types of valves should be mounted in the return flow. If the pvalues exceed 60 kpa, attention should be paid to the development of noise. TwoWay Valves Direction of flow always from port to port Port : Outlet ThreeWay Valves These valves are preferably used as mixing valves, this means: Port : Total flow outlet Port : Controlled flow Port : ypass Fig. 2. Threeway valve operation ThreeWay Valves with ypass These valves simplify the installation, which is depending on the layout of the pipework, as the bypass pipe is part of the valve. The information for the normal threeway valves is also valid for this type. outlet outlet Fig. 1. Twoway valve operation Fig. 3. Threeway valve with bypass 3 EN00308GE51 R1002

4 MOUNTING When installing the valve care must be taken that the flow direction is correct (see section "Typical Operation"). The valve must not be mounted with the stem pointing downward. The adjustment cap must be removed from the valve only when the actuator is fitted. The valve should be installed as stressfree as possible with a tightening torque of 25 to 30 Nm. The valve is supplied complete with mounting instructions. The water quality must meet VDI 2035 requirements. CCESSORIES Valves V5832 need two connection sets, valves V58 three connection sets, and valves V58C four connection sets. Connection Pipe Size DN Order Number Connection Set Description Soldering 12 mm 15 mm C15FS C20FS Consisting of 1 union nut, 1 solder bush, and 1 gasket External Thread R3/8" R1/2" C15FT C20FT Consisting of 1 union nut, 1 tailpiece, and 1 gasket *Cannot be purchased from Honeywell Dimensions of Connection Sets a c d Order Number G1/2 G3/4 12 mm 15 mm C15FS C20FS G1/2 G3/4 R3/8 R1/2 C15FT C20FT EN00308GE51 R1002 4

5 DIMENSIONS Twoway valve 6. 5 Str ok e * 6.5 Stroke* 18 M30x1.5 llow 130mm for the actuator and clearance for removal a a b d d DN15 DN G1/ /8" x 14 S G3/4 Threeway valve 6. 5 Str ok e * 6.5 Stroke* 18 M30x1.5 llow 130mm for the actuator and clearance for removal a a b b c dd DN15 DN G1/2 G1/ /8" G3/4 x 14 S 84 c a Threeway valve with bypass 6. 5 Str ok e * 6.5 Stroke* 18 M30x1.5 llow 130mm for the actuator and clearance for removal aa b b c c dd DN G1/ /8" G3/4 x 14 S * Modulating valves, only (in the case of on/off valves, the stroke amounts to 2.5 mm and the closure distance to 14 mm). Fig. 4. Dimensions V5832/V58,C in mm 5 EN00308GE51 R1002

6 V5832/V58,C SMLL LINER VLVE PN16 SPRE PRTS Valve inserts are provided as spare parts for the V5832 and V58,C small linear valves. When the tool WV 108 is used, the valve inserts can be changed without draining the system. Order Number DN k VS Order Number Valve Insert V V V V V V V V V * V * *For on/off control Order Number DN k VS Order Number Valve Insert V / V58C V / V58C V / V58C V / V58C V / V58C V / V58C V / V58C V / V58C V / V58C V584007* / V58C4003* V584015* / V58C4011* *For on/off control The following valve inserts are interchangeable Twoway valves: k VS 0.16, 0.25, 0.40, and 0.63 k VS 1.0 and 1.6 k VS 2.5 and 4.0 Threeway valves: k VS 0.25, 0.40, 0.63, and 1.0 k VS 2.5 and 4.0 Control Products Honeywell G Hardhofweg D74821 Mosbach Phone: (49) Fax: (49) Subject to change without notice. Printed in Germany Manufacturing location certified to EN00308GE51 R1002