B Style Electric Motors and Valves

Transcription

1 Style Electric Motors and Valves Shutoff/ontrol Motors oom ontrol motors are 22 RPM for 344 series (0.7 second shutoff valves) and 25 RPM for 346 and 356 series (0.6 second shutoff valves) for 12 VD systems. Available with E or E series motors with DIN or ALE versions. E type motors work with DPDT (double pole, double throw) switch. E type motors work with simple SPST (single pole, single throw) on/off switch and are compatible with all sprayer controls. urrent draw less than 2 amps (1.7 amps at 40 in-lbs.). Electrical connectors can be ordered with a standard number. See page 98 for more information. Note: 2-way control motors can be rotated 180 to change the cable outlet direction on the valve. There is also an adapter to rotate motors 90, contact your local representative for more information. An internal fuse protects the valve and your electrical system, and it resets automatically by disconnecting power to the motor for 20 seconds. Available for either positive or negative switched electrical systems with a sturdy, built-in double sealed grommet and flat gasket that seals the DIN connector versions. Motor and DIN cables are made of polyurethane. Direct coupled visual indicator to verify position/operation. Yellow oval indicates 22 RPM motor. Yellow diamond indicates 25 RPM motor. over fits snugly over the motor cavity to reduce air space and eliminate condensation. It s sealed and sonically welded to comply with the IP67 rating for submersion under water. Permanent etched marking with complete motor number and date coded (year, date, month). Double-wall construction of the gearbox increases strength and maintains permanent lubrication of the durable, all-metal gears. Motor head assembly is easily detached by pulling a retaining pin allowing manual operation or easy replacement of the motor. Regulating Motors hoosing the proper regulating motor speed is important to maximizing the sprayer s performance. Three speeds are offered at this time: 1 RPM, 3 RPM and 6 RPM. The 1 RPM speed is used mostly in manual systems; it is too slow for automated rate control. The other two speeds are used in automated systems. The 3 RPM is the most popular and opens the valve to the maximum flow in about 6 seconds for the RL valve and about 10 seconds for the PR valves. The 6 RPM motor cuts those times in half. POSITIVELY-SWITHED E SHUTOFF MOTORS POSITIVELY-SWITHED VALVES ARE STANDARD LAK RED WHITE E SHUTOFF AND R REGULATING MOTORS INLUDES: E, R, RL & PR VALVE TYPES DIN and able Electrical onnector oth DIN and motor cables are made of polyurethane and are pressure extruded creating a round cable for improved sealing. Polyurethane has twice the strength and three times the tear and abrasion resistance of PV. Motor cables include over-molded plugs that seal off the ends of cables and wires to prevent seepage. onductor insulation uses familiar color coding of red, white and black. DIN cable connectors are constructed for a special over molded elastomeric material that does not require a flat gasket to be sealed. The center screw is made of stainless steel. How to Order: Example: , 10 ft. (3 meter) DIN cable. VEHILE ATTERY 12VD SINGLE-POLE SINGLE-THROW SWITH (SPST) NEGATIVELY-SWITHED E SHUTOFF MOTORS NEGATIVELY-SWITHED VALVES ARE SPEIAL AND ARE NOTATED Y AN N IN THE PART NUMER LAK RED WHITE VEHILE ATTERY 12VD LAK RED JUMPER WIRES DOULE-POLE DOULE-THROW SWITH (DPDT) DIN able able 1.58 (0.5 meter) DIN cable 58 (1.5 meter) DIN cable VEHILE ATTERY 12VD SINGLE-POLE SINGLE-THROW SWITH (SPST) 108 (3 meter) DIN cable 208 (6 meter) DIN cable DIN cables are ordered separately. 71

2 Style Motors Style Shutoff Motor Numbers E Positive switch motor 344 Series *bec negative switch motor be switch motor current draw (AMPS)** 346 and 356 Series current draw (AMPS)** 344 E Positive *bec negative be switch motor switch motor switch motor cable length P03 * N03 * P03 * N03 * (0.3 meter) cable P05 * N P05 * N (0.5 meter) cable P15 * N15 * P15 * N15 * (1.5 meter) cable P60 * N60 * P60 * N60 * (6 meter) cable DP * DN * D DP * DN * D DIN Electrical onnector Items marked with * are non-stock items. ** urrent draw is a nominal 13.8 VD and will vary dependent upon valve usage and chemicals used. Note: DIN cables are ordered separately. *ypass Valve (Normally Open) E Motors E Positive switch motor 344 Series *bec negative switch motor be switch motor current draw (AMPS)** 346 and 356 Series current draw (AMPS)** 344 E Positive *bec negative be switch motor switch motor switch motor cable length P03 * N03 * P03 * N03 * (0.3 meter) cable P05 * N P05 * N (0.5 meter) cable P15 * N15 * P15 * N15 * (1.5 meter) cable P60 * N60 * P60 * N60 * (6 meter) cable DP * DN * D DP * DN * D DIN Electrical onnector Items marked with * are non-stock items. ** urrent draw is a nominal 13.8 VD and will vary dependent upon valve usage and chemicals used. Note: DIN cables are ordered separately. 344 & 346 Regulating Motors Speed (RPM) R & RL Motor no. PR Motor no. aa344 current draw (AMPS)** AA346 cable length 1 * * * * * * * * * D * D 3 * * * * * * * * * D * D 6 * * * * * * * * (0.3 meter) cable (0.5 meter) cable (1.5 meter) cable (6 meter) cable DIN Electrical onnector (0.3 meter) cable (0.5 meter) cable (1.5 meter) cable (6 meter) cable DIN Electrical onnector (0.3 meter) cable (0.5 meter) cable (1.5 meter) cable (6 meter) cable 6 * D * D Items marked with * are non-stock items. ** urrent draw is a nominal 13.8 VD and will vary dependent upon valve usage and chemicals used. Note: DIN cables are ordered separately. See page 71 for DIN cable options DIN Electrical onnector 72

3 Electric Regulating Valves DirectoValve Electric Pressure Regulating Valves The proper regulating valve will enhance the operation of a sprayer, especially one with an automatic rate controller. While advanced electronics provide features and control, the proper regulating valve helps the system to respond quickly to input changes and functions over a wide range of application rates. hoosing the proper valve involves determining the maximum capacity required, the range of application rates and the proper motor speed. System apacity A regulating valve s system requirements will depend on the application amount and the pumping capacity. Additionally, the regulating valve can be used in bypass or throttling mode. In throttling mode, the flow through the valve will be applied through the nozzles. In bypass mode, the excess flow from the pump is recirculated. A valve that works well throughout the flow spectrum has the best chance to work in all situations. Types of Regulating Valves Special ball shapes make regulating valves more responsive and able to work with both high and low application rates. Most agricultural sprayers use either a % of Maximum Flow Regulating Valve Flow urves PR all RL all R all utterfly 2-way ball valve or butterfly valve for regulating purposes. When considering sizing a regulating valve, the first concern is to understand the valve s flow curve to determine how efficiently the valve will regulate. Figure 1 shows typical flow curves for DirectoValve regulating type valves. This will help to decide the type of valve to use % of Travel (Figure 1) R Type Valve utterfly Valve RL Valve PR Valve R Type and utterfly Valves As shown on the graph, the butterfly valve has the most non-linear flow curve for final 1/3 (30 ) of travel leading to an increase of 75% in flow through the valve. The straight 2- way R ball curve is not quite as steep, with the flow through the valve increasing by 60% over the last 30 of travel. The R ball, however, has the additional disadvantage of not allowing significant flow during the first 1/3 of its rotation. Since a small change of rotation causes a significant change using these valves, trying to regulate large flows when the valve is two thirds to full open presents a challenge. RL Valve Spraying Systems o. has developed a special ball that allows the valve to start regulating earlier thus extending the regulating range. This special ball valve also increases flow and the linear characteristic of the valve during the first 3/4 of the valve cycle. The flow from the valve starts 10º earlier, than a regular R type ball and increases the flow of the RL ball during the first 70% of travel (Figure 1). The maximum capacity is about 10% less than an R type valve. all Type Regulating Valves model number 344R-2 344R-3 344RL-2 * 344PR-2 * 344PR-3 346R-2 346R-3 * 346PR-2 * 346PR-3 PR Valve The PR valve uses a 3-way valve body and a ball with a wedge removed. The combination of this ball and a motor that rotates past the standard 90º results in a valve with an almost linear flow curve. The 2PR version has one outlet plugged. The 3PR version allows bypass flow to return to the tank. As noted in Figure 1, the percentage of flow increases by approximately the amount of ball travel thus avoiding the rapid change seen with standard ball valves and butterfly valves. * Not available in stainless steel. MAXIMUM PRESSURE FLOW RATE AT A 5 PSI (0.34 bar) PRESSURE DROP 300 PSI (20 bar) 32 GPM (121 l/min) 300 PSI (20 bar) 24 GPM (91 l/min) 300 PSI (20 bar) 27 GPM (102 l/min) 300 PSI (20 bar) 12 GPM (45 l/min) 300 PSI (20 bar) 12 GPM (45 l/min) 150 PSI (10 bar) 100 GPM (379 l/min) 150 PSI (10 bar) 64 GPM (242 l/min) 150 PSI (10 bar) 53 GPM (200 l/min) 150 PSI (10 bar) 53 GPM (200 l/min) 73

4 Electric Regulating all Valves 344 and 346 Pressure Regulating all Valves The 340 series electrical regulating valves are designed to produce linear flow regulation and shutoff control in agricultural applications. oth models are available in several styles and motor speeds to accommodate different types of applications. Features: n Available in 2-way and 3-way versions. n Available in 1, 3, or 6 RPM motor speeds. Note: The PR versions cycle time is double that of an R or RL version. n Two-wire lead provides easy installation with 12 VD systems. n Low power consumption, less than 1 amp. n Offered in a variety of inlet/outlet connections. See pages 96 and 97 for additional information and options. n Wetted parts are Nylon, polypropylene, stainless steel, Teflon, and Viton. n See pages for additional information on style motors. R & RL Series 344 PR Series FLOW PATH FOR 3-WAY REGULATING ALL VALVES (AS VIEWED FROM TOP) OUT OUT *NOTE: MUST USE SIDE PORT AS INLET. IN* 346 R Series utterfly Valve AA()244-3/4 Remote ontrol Electric Regulating utterfly Valve The AA244 remote control electric regulation valve has been specifically designed to provide remote pressure control in agricultural applications using DirectoValve AA144A or AA145 solenoid shutoff valves. Features: n Unrestricted flow when wide open 5 PSI (0.34 bar) pressure loss for 28.4 GPM (107 l/min) flow. n ypass flow rate: 2 GPM ( PSI (0.7 bar). n Operates in 12 VD system and may be controlled by a double-pole double-throw spring-centered switch. n Maximum operating pressure of 100 PSI (7 bar). n Two-wire lead for use in 12 VD system. n 3/49 (F) NPT or SPT connections. n Easy installation (flows either direction). n Good corrosion resistance. n Low current draw (0.10 AMP). n 20 second response time. 346 PR Series Specify model number. Example: AA()244-3/4 () = SPT 74

5 Sample Valve Part Number: ()344RL 2FS 0115A LANK () 344/346 OUTLET THREADS ALL THREADS TO E NPT ALL THREADS TO E SPT MODEL SPEIFIATIONs REGULATING VALVE Q F END APS OR OUTLET FITTINGS 3/49 PIPE THREAD (344 SERIES ONLY) 19 PIPE THREAD (344 SERIES ONLY) 11/49 PIPE THREAD (346 SERIES ONLY) 11/ PIPE THREAD (346 SERIES ONLY) QUIK ONNET (344 SERIES ONLY) 50 SERIES FLANGE WIRING ONNETORS SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. See page 98 for electrical connectors and codes. MOTOR ALEs 0.5-METER ALE MOTOR SPEIFIATIONs F75 #3 75 SERIES FLANGE (346 SERIES ONLY) #4 * METER ALE * METER ALE R REGULATING VALVE * METER ALE RL LINEAR REGULATING VALVE (344 SERIES ONLY) *PR PRESSURE REGULATING VALVE *Not available in stainless steel. #5 #6 D DIN ONNETOR Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. VALVE TYPEs 2 2-WAY VALVE 3 3-WAY VALVE (PR & R ONLY) See pages 96 and 97 for Q and flange fittings. #Q #F/F Motor Speeds 1 RPM (18 second cycle time) Motor 3 RPM (6 second cycle time) Motor 6 RPM (3 second cycle time) Motor Note: PR series cycle times are doubled. Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately ALL MATERIAL SPEIFIATIONs n 3, 4, 5, 6: When ordering 3/49 (3), 19 (4), 11/49 (5) or 11/ (6) threaded NPT or SPT inlet/outlet type valve connections, the inlets and outlets will be included during assembly. n F: When ordering F or F75 (flange) type valve connections, the inlet/outlet fittings are ordered separately. lamps and flange fittings are required. See pages 96 and 97 for flange fitting options. n Q: When ordering Q (Quick onnect) hose barb type valve fittings, the inlet/outlet connections are ordered separately. Two 455 Q fittings are required for 2-way valves and three each for 3-way valves. See page 97 for Q options. Note: Many valve configurations are possible by mixing and matching flange fittings. repair kits A344AE-KIT LANK S POLYPROPYLENE ALL STAINLESS STEEL ALL (R & RL SERIES ONLY) A346-KIT Note: A344AE-KIT for 344A& Valves 75

6 344 Series Electric Shutoff Valves 344 shutoff ball valves are available with E or E series motors and with cable or DIN electrical connections. See page 71 for more information on DirectoValve motors. Features: n 22 RPM, 0.7 second shutoff fully open to close. n Flexible inlet/outlets provide quick simple plumbing for a single valve. See page 77 for more information. n Available in 2-way or 3-way versions. 2-way valves allow complete shutoff while the 3-way valves divert flow to a bypass line when boom controls are shut off. n Stainless steel stem with optional polypropylene or stainless steel ball. n Maximum pressure rating is 300 psi (20 bar). n The flow rate for the 344E 2-way valve is 32 GPM (121 l/min) flow rate with a 5 psi (0.34 bar) pressure drop. n The flow rate for the 344E 3-way valve is 24 GPM (91 l/min) with a 5 psi (0.34 bar) pressure drop. n Wetted parts are Nylon, Teflon, polypropylene, stainless steel and Viton. (front view) (front view) 344E-24-2-Way Valve FLOW PATH FOR WAY SHUTOFF ALL VALVES (AS VIEWED FROM TOP) OUT OUT 344E-33-3-Way Valve IN* SWITH IN ON POSITION IN* SWITH IN OFF POSITION *NOTE: MUST USE SIDE PORT AS INLET. 76

7 Sample Valve Part Number: ()344E 2FS N15A OUTLET THREADS WIRING ONNETORS LANK () ALL THREADS TO E NPT ALL THREADS TO E SPT END APS OR OUTLET FITTINGS SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. See page 98 for electrical connectors and codes. 344 MODEL SPEIFIATION See page 71 for more information on E and E motors. ALL VALVE MOTOR SPEIFIATIONs switch E E DPDT SPST VALVE TYPEs 22 RPM, 0.7 SEOND SHUTOFF VALVE 2 2-WAY VALVE 3 3-WAY VALVE Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately #3 #Q See pages 96 and 97 for Q and flange fittings. n 3, 4: When ordering 3/49 (3) or 19 (4) threaded NPT or SPT inlet/outlet type valve connections, the inlets and outlets will be completed during the ordering process. n F: When ordering F (flange) type valve connections, the inlet/outlet fittings are ordered separately. Two 50 series clamps and flange fittings are required for 2-way valves and three each for 3-way valves. See pages 96 and 97 for flange fitting options. n Q: When ordering Q (Quick onnect) hose barb type valve fittings, the inlet/outlet connections are ordered separately. Two 455 Q fittings are required for 2-way valves and three each for 3-way valves. See page 97 for Q options. Note: Many valve configurations are possible by mixing and matching flange fittings. 3 3/49 PIPE THREAD 4 19 PIPE THREAD Q F QUIK ONNET 50 SERIES FLANGE #4 #F repair kit N * 03 * N03 * 15 * N15 * 60 * N60 D DN Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. ALL MATERIAL SPEIFIATIONs LANK S MOTOR ALEs A344AE-KIT for 344A& Valves w/ 0.5-METER ALE w/ 0.5-METER ALE POLYPROPYLENE ALL STAINLESS STEEL ALL 77

8 346 Series Shutoff Valves 346E shutoff ball valves are available with E or E series motors with cable or DIN electrical connections. See page 71 for more information on DirectoValve motors. Features: n 25 RPM, 0.6 second shutoff fully open to close. n Available in 2-way or 3-way versions. 2-way valves allow complete shutoff while the 3-way valves divert flow to a bypass line when boom controls are shut off. n The flow rate for the 346E 2-way valve is 100 GPM (379 l/min) with 5 psi (0.34 bar) pressure drop. n The flow rate for the 346E 3-way valve is 64 GPM (242 l/min) with a 5 psi (0.34 bar) pressure drop. n Polypropylene ball with stainless steel stem. n Maximum pressure rating of 150 psi (10 bar). n Available with 11/49, 11/ NPT or SPT (F) threads or 50 series flange fittings. n Wetted parts made of corrosion-resistant materials, glass-reinforced polypropylene, Teflon, stainless steel and Viton. (front view) 346E-25- Valve (front view) FLOW PATH FOR WAY SHUTOFF ALL VALVES (AS VIEWED FROM TOP) OUT OUT 346E-35- Valve IN* SWITH IN ON POSITION IN* SWITH IN OFF POSITION *NOTE: MUST USE SIDE PORT AS INLET. 78

9 Sample Valve Part Number: ()346E 25S N15A OUTLET THREADS WIRING ONNETORS LANK () ALL THREADS TO E NPT ALL THREADS TO E SPT END APS OR OUTLET FITTINGS SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. See page 98 for electrical connectors and codes. 5 11/49 PIPE THREAD 346 MODEL SPEIFIATION See page 71 for more information on E and E motors. ALL VALVE MOTOR SPEIFIATIONs switch E E DPDT SPST VALVE TYPEs 25 RPM, 0.6 SEOND SHUTOFF VALVE 2 2-WAY VALVE 3 3-WAY VALVE 6 11/ PIPE THREAD F F75 #5 See pages 96 and 97 for Q and flange fittings. 50 SERIES FLANGE 75 SERIES FLANGE #F/F75 #6 N * 03 * N03 * 15 * N15 * 60 * N60 D DN MOTOR ALEs w/ 0.5-METER ALE w/ 0.5-METER ALE Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately n 5, 6: When ordering 11/49 (5) or 11/ (6) threaded NPT or SPT inlet/outlet type valve connections, the valve will be completed during the ordering process. n F: When ordering F or F75 (flange) type valve connections, the inlet/outlet fittings are ordered separately. Two clamps and flange fittings are required for 2-way valves and three each for 3-way valves. See pages 96 and 97 for flange fitting options. Note: Many valve configurations are possible by mixing and matching flange fittings. repair kit A346-KIT ALL MATERIAL SPEIFIATIONs LANK S POLYPROPYLENE ALL STAINLESS STEEL ALL (2-WAY VALVE ONLY) 79

10 356 Series Flanged Shutoff Valves The 356E DirectoValve control valve delivers performance and dependability. The trunnion-style valve is a hard-working, commercial-duty control valve made to go the distance. It combines dozens of design features into a control valve that will respond quickly and last longer than other valves. 356E shutoff ball valves are available with E or E series motors with cable or DIN electrical connections. See page 71 for more information on DirectoValve motors. Features: n 25 RPM, 0.6 second shutoff fully open to close. n Flow rate is 100 GPM (379 l/min) with a 5 psi (0.34 bar) pressure drop. n Maximum pressure rating of 150 psi (10 bar). n Wetted parts are polypropylene, stainless steel, carbon-filled Teflon, Viton and Ryton. n 50 series flange fittings reduce leaks and allow various inlet/outlet connections. See pages 96 and 97 for more information. (front view) 356E- Valve (35 mm) Mounting foot pattern for 5/169 (8 mm) bolts. earings above and below the ball maintain precise position and assure long life. Wear-resistant, carbon-filled Teflon seal improves durability and minimizes the potential for leakage. TeeJet 50 series flanged fittings at the inlet and outlet permit easy attachment of hoses or to a manifold. It s compatible with other flanged fittings on the market. Fasteners and mounting foot made of 303 stainless steel to prevent corrosion, provide strength and provide easy mounting. A 5/169 or 8 mm bolt can be used to mount the valve. Uniquely shaped, 316 stainless steel ball, polished for longer life, is the heart of this valve. Material doesn t get trapped as easily because the valve is self-cleaning. 80

11 Sample Valve Part Number: 356E N15A 356 MODEL SPEIFIATION See page 71 for more information on E and E motors. 356 ALL VALVE MOTOR SPEIFIATIONs switch E E DPDT SPST 25 RPM, 0.6 SEOND SHUTOFF VALVE 50 series flange inlet/outlet N * 03 * N03 * 15 * N15 * 60 * N60 D DN MOTOR ALEs w/ 0.5-METER ALE w/ 0.5-METER ALE Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. WIRING ONNETORS SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. See page 98 for electrical connectors and codes. See pages 96 and 97 for flange fittings. Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately n F: Two 50 series clamps and flange fittings are required. See pages 96 and 97 for flange fitting options. n Q: Q (Quick onnect) hose barb type valve fittings are not normally used due to flow limitations. See page 97 for more information on Q fittings. Note: Many valve configurations are possible by mixing and matching flange fittings. repair kit A356-KIT 81

12 Normally-Open (ypass) Valves The 344E, 346E and 356E valves are available in a normally-open configuration. Unlike standard shutoff ball valves, which are normally closed, normally-open valves will be in the closed position when the signal line (white wire or DIN terminal 2) is energized (+12 VD) and will be in the open position when the signal is de-energized. Features: n Normally-open valves are wired in the identical manner to normally-closed, E style valves and operated by a single-pole single-throw (SPST) switch. n Refer to the standard DirectoValve shutoff valve pages for typical features and specifications of a dump valve (344E, see page 76) (346E, see page 78) (356E, see page 80) 82

13 Sample Valve Part Number: () FS N15A LANK () OUTLET THREADS (for 344 & 346) ALL THREADS TO E NPT ALL THREADS TO E SPT MODEL SPEIFIATIONs (for 344, 346 & 356) E ALL VALVE E ALL VALVE E ALL VALVE VALVE TYPEs (for 344 & 346) 2 2-WAY VALVE 3 3-WAY VALVE Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately #3 #4 #5 #6 #Q #F/F75 n 3, 4, 5, 6: When ordering 3/49 (3), 19 (4), 11/49 (5) or 11/ (6) threaded NPT or SPT inlet/ outlet type valve connections, the inlets and outlets will be included during assembly. n F: When ordering F or F75 (flange) type valve connections, the inlet/outlet fittings are ordered separately. lamps and flange fittings are required. See pages 96 and 97 for flange fitting options. n Q: When ordering Q (Quick onnect) hose barb type valve fittings, the inlet/outlet connections are ordered separately. Two 455 Q fittings are required for 2-way valves and three each for 3-way valves. See page 97 for Q options. Note: Many valve configurations are possible by mixing and matching flange fittings. END APS OR OUTLET FITTINGS (for 344 & 346) Q F F75 See pages 96 and 97 for Q and flange fittings. 3/49 PIPE THREAD (344 ONLY) 19 PIPE THREAD (344 ONLY) 11/49 PIPE THREAD (346 ONLY) 11/ PIPE THREAD (346 ONLY) QUIK ONNET (344 ONLY) 50 SERIES FLANGE 75 SERIES FLANGE (346 ONLY) repair kit A344AE-KIT A346-KIT WIRING ONNETORS (for 344, 346 & 356) SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. See page 98 for electrical connectors and codes. MOTOR ALEs (for 344, 346 & 356) w/ 0.5-METER ALE N w/ 0.5-METER ALE * 03 * N03 * 15 * N15 * 60 * N60 D DN Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. ALL MATERIAL SPEIFIATIONs (for 344 & 346) LANK S POLYPROPYLENE ALL STAINLESS STEEL ALL 83

14 440 Series Manifold Shutoff Valves The TeeJet 440E series DirectoValve manifold provides a convenient, compact solution for the installation of multiple 344E electric ball valves. This system eliminates the need for custom fabrication of pipe or hose manifolds, drastically reducing both installation time and the chance for fluid leaks. 440E shutoff ball valves are available with E or E series motors with cable or DIN electrical connections. See page 71 for more information on DirectoValve motors. Features: n ased on proven design of 344 ball valves. 22 RPM, 0.7 second shutoff fully open to close. n Quick, simple plumbing of up to five electric ball valves. n Flexible inlet and outlet connection options. n Easy mounting with built-in brackets. n Maximum pressure rating of 300 PSI (20 bar). n Flow rate 26 GPM (98 l/min) with 5 PSI (0.34 bar) pressure drop (flow rate may vary based on number of valves and inlet size). n Incorporates an internal resettable fuse. n 12 VD operation. n Stainless steel stem with optional polypropylene or stainless steel ball. (front view) 441E-4T4T- Valve (front view) 443E-4T4T- Valve 84

15 Sample Valve Part Number: ()443E 4S4H4T N15A LANK () OUTLET THREADS See page 71 for more information on E and E motors. ALL THREADS TO E NPT ALL THREADS TO E SPT 440 MANIFOLD SIZEs 1 1-VALVE MANIFOLD 2 2-VALVE MANIFOLD 3 3-VALVE MANIFOLD 4 4-VALVE MANIFOLD 5 5-VALVE MANIFOLD END APS OR OUTLET FITTINGS MOTOR SPEIFIATIONs switch E E DPDT SPST 22 RPM, 0.7 SEOND SHUTOFF VALVE 3 3/49 PIPE THREAD 4 19 PIPE THREAD ALL MATERIAL SPEIFIATIONs LANK S LEFT/RIGHT SIDE INLET FITTINGS 4T 4H 5H 1T 1T POLYPROPYLENE ALL STAINLESS STEEL ALL 19 PIPE THREAD 19 HOSE AR 11/49 HOSE AR INLET LANK 1/49 THREAD GAUGE PORT Note: Right and left sides are as seen with outlets facing towards you (front view). 4T 4H, 5H N * 03 * N03 * 15 * N15 * 60 * N60 D DN WIRING ONNETORS SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. See page 98 for electrical connectors and codes. MOTOR ALEs w/ 0.5-METER ALE w/ 0.5-METER ALE Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. repair kit Q QUIK ONNET A344AE-KIT F 50 SERIES FLANGE Inlet/Outlet REQUIRED ONNETIONS #3 #Q See pages 96 and 97 for more information on Q and flange fittings. #4 #F n 3, 4: When ordering a standard 440 series manifold, inlets/outlets will be completed in the ordering process. No additional valve connections are required. n F: When ordering F (flange) type valve outlet connections, only the outlets will be 50 series flange fittings and are ordered separately. One 50 series clamp and flange fitting is required for each valve in the manifold. See pages 96 and 97 for flange fitting options. The inlets will be standard 440 connections as described in the ordering process. n Q: When ordering Q (Quick onnect) type valve outlet fittings, only the outlets will be Q fittings and are ordered separately. One 452 Q hose barb connection is required for each valve in the manifold. See page 97 for Q hose barb options. The inlets will be standard 440 connections as described in the ordering process. Note: Other valve configurations are possible by mixing and matching flange fittings. 85

16 450 Series Shutoff Manifold 450E manifolds are available with E or E series motors with cable or DIN electrical connections. See page 71 for more information on DirectoValve motors. Features: n 22 RPM, 0.7 second shutoff fully open to close. n Available in 2-way version only. Pressure regulating valves can be incorporated. n Flexible inlet/outlet connections allow for quick, simple plumbing for as many valves as needed for your sprayer. n Stainless steel stem with optional polypropylene or stainless steel ball. n Maximum pressure rating of 200 psi (14 bar). n The flow rate for the 450E 2-way valve is 32 GPM (121 l/min) with 5 psi (0.34 bar) pressure drop. n Wetted parts are Nylon, Teflon, polypropylene and Viton. 451E-2F- Valve (front view) 453E-2N3- Manifold (front view) 86

17 Sample Valve Part Number: ()453E 2FS N15A WIRING ONNETORS LANK () OUTLET THREADS See page 71 for more information on E and E motors. ALL THREADS TO E NPT ALL THREADS TO E SPT MANIFOLD SIZEs 1 1-VALVE MANIFOLD 2 2-VALVE MANIFOLD 3 3-VALVE MANIFOLD 4 4-VALVE MANIFOLD 5 5-VALVE MANIFOLD MOTOR SPEIFIATIONs switch E E MODEL SPEIFIATION DPDT SPST MANIFOLD 22 RPM, 0.7 SEOND SHUTOFF VALVE Note: 3-way valve type not available on 450 manifold. #3 #Q See pages 96 and 97 for Q and flange fittings. VALVE TYPE 2 2-WAY VALVE 2N 2-WAY VALVE, NARROW END APS OR OUTLET FITTINGS 3 3/49 PIPE THREAD 4 19 PIPE THREAD Q F QUIK ONNET 50 SERIES FLANGE #4 #F SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. N * 03 * N03 * 15 * N15 * 60 * N60 D DN See page 98 for electrical connectors and codes. MOTOR ALEs w/ 0.5-METER ALE w/ 0.5-METER ALE Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately n 3, 4: When ordering 3/49 (3) or 19 (4) NPT or SPT threaded connections, the valve outlet connection will be completed during the ordering process. For the inlets, the 75 series flange fittings are ordered separately. Two 75 series clamps and fittings are required per manifold assembly. See pages 96 and 97 for flange fitting options. n F: When ordering F (flange) type valve connections, the inlet/outlet fittings are ordered separately. For the outlet, one 50 series clamp and flange fitting is required per valve. For the inlets, two 75 series clamps and flange fittings are required per manifold assembly. See pages 96 and 97 for flange fitting options. n Q: When ordering Q (Quick onnect) type valve outlet fittings, only the outlets will be Q fittings and are ordered separately. One 452 Q hose barb connection is required for each valve in the manifold. See page 97 for Q hose barb options. The inlets will be standard 440 connections as described in the ordering process. ALL MATERIAL SPEIFIATIONs LANK POLYPROPYLENE ALL S STAINLESS STEEL ALL repair kit A344AE-KIT Note: Many manifold configurations are possible by mixing and matching flange fittings. 87

18 490 Series Shutoff Manifold The 490E DirectoValve control valve delivers performance and dependability. The trunnion-style valve is a hard-working, commercial-duty control valve made to go the distance. It combines dozens of design features into a valve that will respond quickly and last longer than other valves. Available with E or E series motors with cable or DIN electrical connections. See page 71 for more information on DirectoValve motors. Features: n 25 RPM, 0.6 second shutoff fully open to close. See page 71 for more information about DirectoValve motors. n Flexible 50 series flange fitting inlet/outlet connections allow quick, simple plumbing for as many valves as needed for your sprayer. n Available in 2-way version only. Pressure regulating valves can be incorporated. n A uniquely designed 316 stainless steel ball reduces material that can be trapped causing corrosion ball drag that can shorten the life of a valve. n Flow rate is 100 GPM (379 l/min) with 5 psi (0.34 bar) pressure drop. n Maximum pressure rating of 150 psi (10 bar). n Wetted parts are polypropylene, stainless steel, carbon-filled Teflon, Viton and Ryton. n Wear-resistant carbon-filled Teflon seals improve durability and minimize the potential for leaks. n Fasteners and mounting foot made of stainless steel to prevent corrosion, provide strength and provide easy mounting using a 5/169 or 8 mm bolt. 491E- Valve (front view) (front view) 493E- Valve 88

19 Sample Valve Part Number: 493E N15A MODEL SPEIFIATION MOTOR ALEs WIRING ONNETORS MANIFOLD MANIFOLD SIZEs 1 1-VALVE MANIFOLD 2 2-VALVE MANIFOLD 3 3-VALVE MANIFOLD 4 4-VALVE MANIFOLD 5 5-VALVE MANIFOLD N * 03 * N03 * 15 * N15 * 60 * N60 D DN w/ 0.5-METER ALE w/ 0.5-METER ALE SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. See page 98 for electrical connectors and codes. 50 series flange inlet/outlet Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. MOTOR SPEIFIATIONs switch E E DPDT SPST 25 RPM, 0.6 SEOND SHUTOFF VALVE See pages 96 and 97 for flange fittings. See page 71 for more information on E and E motors. Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately n F: For the outlets, one 50 series clamp and fitting is required per valve. For the inlets, two 75 series clamps and flange fittings are required. See pages 96 and 97 for flange fitting options. n Q: Q (Quick onnect) hose barb type valve fittings are not normally used due to flow limitations. See page 97 for more information on Q fittings. Note: Many manifold configurations are possible by mixing and matching flange fittings. repair kit A356-KIT 89

20 460 Series 2-Way Manifold The 460E ball valve manifold gives you continued reliability. Available with E or E series motors with cable or DIN electrical connections. See page 71 for more information on DirectoValve motors. Features: n 22 RPM, 0.7 second shutoff fully open to close. n With a choice of threaded, Q (Quick onnect) hose barbs or 50 series flange fitting outlet connections, the 460E manifold allows quick, simple plumbing for as many valves as needed for your sprayer. n Stainless steel stem and ball. n Flow rate is 25 GPM (94 l/min) with 5 psi (0.34 bar) pressure drop. n Maximum pressure rating of 300 psi (20 bar). n The 460E valve series is also available in 3-way and flow back versions. See page 92 for and 3E, 3-way versions and page 94 for 460F flow back version. 461E-2F- Valve (front view) 463E-2F- Manifold (front view) 90

21 Sample Valve Part Number: ()463E 2F N15A LANK () OUTLET THREADS ALL THREADS TO E NPT ALL THREADS TO E SPT MODEL SPEIFIATION MANIFOLD VALVE TYPE 2 2-WAY VALVE See page 92 for 3-way valve. END APS OR OUTLET FITTINGS 3 3/49 PIPE THREAD WIRING ONNETORS SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. See page 98 for electrical connectors and codes. MOTOR SPEIFIATIONs switch E E MANIFOLD SIZEs DPDT SPST See page 71 for more information on E and E motors. 1 1-VALVE MANIFOLD 2 2-VALVE MANIFOLD 3 3-VALVE MANIFOLD 4 4-VALVE MANIFOLD 5 5-VALVE MANIFOLD 22 RPM, 0.7 SEOND SHUTOFF VALVE Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately #3 #Q See pages 96 and 97 for Q and flange fittings. n 3, 4: When ordering 3/49 (3) or 19 (4) NPT or SPT threaded connections, the valve outlet connection will be completed during the ordering process. For the inlets to be threaded, the 50 series flange fittings are ordered separately. Two 50 series single clamps and fittings are required per manifold assembly. See pages 96 and 97 for flange fitting options. n F: For the flange fitting versions, one 50 series single clamp and flange fitting is required per valve. For the inlets, two 50 series single clamps and flange fittings are required per manifold assembly. See pages 96 and 97 for flange fitting options. n Q: When ordering Q (Quick onnect) hose barb type valve fittings. For the outlet, one 455 Q hose barb connection is required per valve. 460 inlets are 50 series standard flanges. Any two 50 series fittings and clamps may be ordered. For the inlets to be Q, requires two each, P460-PP Q flange adapters, 50 series single clamps and 455 Q hose barb connections per manifold assembly. See page 97 for Q fitting options. Note: Many manifold configurations are possible by mixing and matching flange fittings PIPE THREAD Q F QUIK ONNET 50 SERIES FLANGE #4 #F repair kit A460-KIT N * 03 * N03 * 15 * N15 * 60 * N60 D DN MOTOR ALEs w/ 0.5-METER ALE w/ 0.5-METER ALE Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. 91

22 460 Series 3-Way Manifold The 460E ball valve manifold gives you continued reliability. Available with E or E series motors with cable or DIN electrical connections. See page 71 for more information on DirectoValve motors. Features: n 22 RPM, 0.7 second shutoff fully open to close. 461E-3EF- Valve n Version has VisiFlo color-coded settings that can be used to match multiple tips. n Version E has a single adjustment. n With a choice of threaded, Q (Quick onnect) hose barbs or 50 series flange fitting outlet connections, the 460E manifold allows quick, simple plumbing for as many valves as needed for your sprayer. n Stainless steel stem and ball. n Flow rate is 25 GPM (94 l/min) with 5 psi (0.34 bar) pressure drop. n Maximum pressure rating of 300 psi (20 bar). n The 460E valve series is also available in 2-way and flow back versions. See page 90 for 460E 2-way version and page 94 for 460F flow back version. 461E-3F- Valve 463E-3F- Manifold 463E-3EF- Manifold (front view) 92

23 Sample Valve Part Number: ()463E 3F N15A LANK () OUTLET THREADS ALL THREADS TO E NPT ALL THREADS TO E SPT MODEL SPEIFIATION MANIFOLD VALVE TYPE 3 3-WAY VALVE 3E See page 90 for 2-way valve. END APS OR OUTLET FITTINGS WIRING ONNETORS SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. See page 98 for electrical connectors and codes. MOTOR SPEIFIATIONs switch E E MANIFOLD SIZEs DPDT SPST See page 71 for more information on E and E motors. 1 1-VALVE MANIFOLD 2 2-VALVE MANIFOLD 3 3-VALVE MANIFOLD 4 4-VALVE MANIFOLD 5 5-VALVE MANIFOLD 22 RPM, 0.7 SEOND SHUTOFF VALVE Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately 3 3/49 PIPE THREAD 4 19 PIPE THREAD Q F #3 #Q See pages 96 and 97 for Q and flange fittings. QUIK ONNET 50 SERIES FLANGE n 3, 4: When ordering 3/49 (3) or 19 (4) NPT or SPT threaded connections, the valve outlet connection will be completed during the ordering process. For the inlets to be threaded, the 50 series flange fittings are ordered separately. Two 50 series double clamps and four flange fittings are required per manifold assembly. See pages 96 and 97 for flange fitting options. n F: For the flange fitting versions, one 50 series single clamp and flange fitting is required per valve. For the inlets, two 50 series double clamps and four flange fittings are required per manifold assembly. See pages 96 and 97 for flange fitting options. n Q: When ordering Q (Quick onnect) hose barb type valve fittings. For the outlet, one 455 Q hose barb connection is required per valve. 460 inlets are 50 series standard flanges. Any four 50 series fittings and two double clamps may be ordered. For the inlets to be Q, requires four each, P460-PP Q flange adapters, 455 Q hose barb connections and two 50 series clamps per manifold assembly. See pages 96 and 97 for Q and flange options. Note: Many manifold configurations are possible by mixing and matching flange fittings. #4 #F repair kit A460-KIT N * 03 * N03 * 15 * N15 * 60 * N60 D DN MOTOR ALEs w/ 0.5-METER ALE w/ 0.5-METER ALE Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. 93

24 450F and 460F Flow ack Manifolds The 450F and 460F flow back valves allow pressure from the boom lines to be relieved back to the tank when the valve is switched to the off position. Available with E or E series motors with cable or DIN electrical connections. See page 71 for more information on DirectoValve motors. Features: n 22 RPM, 0.7 second shutoff fully open to close. n With a choice of threaded, Q (Quick onnect) hose barbs or 50 series flange fitting outlet connections, the 450F and 460F manifolds allow quick, simple plumbing for as many valves as needed for your sprayer. n hoice of polypropylene or stainless steel ball with stainless steel stem for 450F valve series. Stainless steel stem and ball for 460F valve series. n Flow rate for 450F is 32 GPM (120 l/min) with 5 PSI (0.34 bar) pressure drop per valve. Flow rate for 460F is 24 GPM (91 l/min) with 5 PSI (0.34 bar) pressure drop per valve. n The 450F offers a maximum pressure rating of 200 PSI (14 bar). The 460F offers a maximum pressure rating of 300 PSI (20 bar). n The 450F valve series is also available in 2-way versions while the 460F valve series are also available in 2-way and 3-way versions. (front view) 461E-3F4- Valve 453E-3F4- Manifold (front view) 94

25 Sample Valve Part Number: ()463E 3FF N15A LANK () OUTLET THREADS See page 71 for more information on E and E motors. ALL THREADS TO E NPT ALL THREADS TO E SPT MODEL SPEIFIATION MANIFOLD MANIFOLD MOTOR SPEIFIATIONs switch E E MANIFOLD SIZEs DPDT SPST 1 1-VALVE MANIFOLD 2 2-VALVE MANIFOLD 3 3-VALVE MANIFOLD 4 4-VALVE MANIFOLD 5 5-VALVE MANIFOLD 22 RPM, 0.7 SEOND SHUTOFF VALVE Inlet/Outlet REQUIRED ONNETIONS the inlet/outlet fittings are ordered separately See page 92 for 3-way valve. #3 #Q See pages 96 and 97 for Q and flange fittings. n 3, 4: When ordering ¾9 (3) or 19 (4) NPT or SPT threaded connections, the valve outlet connection will be completed during the ordering process. 450F For the inlets, two 75 series flange fittings and two 75 series clamps are required. For the flowback ports, two 455 Quick onnect fittings are required.* 460F For inlets and flowback ports, four 50 series flange fittings and two 50 series double clamps are required per manifold.* n F: For the flange fitting versions, one 50 series single clamp and 50 series flange fitting is required per valve outlet. 450F For the inlets, two 75 series flange fittings and two 75 series clamps are required. For the flowback ports, two 455 Quick onnect fittings are required.* 460F For inlets and flowback ports, four 50 series flange fittings and two 50 series double clamps are required per manifold.* n Q: For Quick onnect versions, one 455 Q hose barb fitting is required per valve outlet. 450F For the inlets, two 75 series flange fittings and two 75 series clamps are required. For the flowback ports, two 455 Quick onnect fittings are required.* 460F For inlets and flowback ports, four 50 series flange fittings and two 50 series double clamps are required per manifold.* *See pages 96 and 97 for flange and Quick onnect fitting options. Note: Many manifold configurations are possible by mixing and matching flange fittings. 3F VALVE TYPE FLOW AK END APS OR OUTLET FITTINGS 3 ¾9 PIPE THREAD 4 19 PIPE THREAD Q F QUIK ONNET 50 SERIES FLANGE #4 #F repair kit A460-KIT A344AE-KIT WIRING ONNETORS SPEIFI ELETRIAL ONNETOR STYLE AND PIN-OUTS. IF NO ONNETOR IS NEEDED LEAVE LANK. N * 03 * N03 * 15 * N15 * 60 * N60 D DN See page 98 for electrical connectors and codes. MOTOR ALEs w/ 0.5-METER ALE w/ 0.5-METER ALE Items marked with * are non-stock items. Please contact your regional sales office for ordering and availability information. Note: DIN cables must be ordered separately. See page 71 for DIN cables. 95

26 Flange Fittings Features: n Polypropylene construction. n Full port design. n Viton O-ring seal available with clamp (not included with flange). Straight Hose arb Flanges Description Series A Part numer 3/49 Hose arb 19 Hose arb 11/49 Hose arb 11/ Hose arb 11/49 Hose arb 11/ Hose arb Hose arb A 111/ P48150-PP (51 mm) (43 mm) 50 P45504-PP (51 mm) (51 mm) 50 P45505-PP (51 mm) (51 mm) 50 P45506-PP (51 mm) (51 mm) 31/ / P48160-PP (78 mm) (46 mm) 31/169 23/ P46067-PP (78 mm) (56 mm) 31/169 23/49 75 P48161-PP (78 mm) (70 mm) n Maximum pressure rating of 200 PSI (14 bar) for 75 series fittings. n Maximum pressure rating of 300 PSI (20 bar) for 50 series fittings. Threaded Flanges (Male) Description Series A Part numer 3/49 Male Pipe Thread 19 Male Pipe Thread 11/ Male Pipe Thread 11/49 Male Pipe Thread 11/ Male Pipe Thread Male Pipe Thread A 50 P()48172-PP (51 mm) (51 mm) 23/ P()48155-PP (51 mm) (56 mm) 23/49 50 P()48156-PP (51 mm) (70 mm) 31/169 21/ 75 P()48165-PP (78 mm) (64 mm) 31/169 21/ 75 P()48166-PP (78 mm) (64 mm) 31/169 / P()48167-PP (78 mm) (65 mm) ()=SPT A A 90 Hose arb Flanges Gauge Port Flange Description Series A Part numer 90 3/49 Hose arb Hose arb 90 11/49 Hose arb 90 11/ Hose arb 90 11/49 Hose arb 90 11/ Hose arb 90 Hose arb 11/ 50 P48151-PP (51 mm) (38 mm) (51 mm) 11/ 50 P48152-PP (51 mm) (38 mm) (51 mm) 115/169 / P72238-PP (51 mm) (49 mm) (65 mm) 115/169 / P72239-PP (51 mm) (49 mm) (65 mm) 31/ /169 / P48162-PP (78 mm) (49 mm) (65 mm) 31/ /169 / P48163-PP (78 mm) (49 mm) (65 mm) 31/ /169 35/ P48164-PP (78 mm) (49 mm) (84 mm) Description Series A Part numer 1/49 Gauge Port 3/89 Gauge Port lank Inlet over 1/49 Gauge Port 3/89 Gauge Port lank Inlet over (51 mm) (51 mm) 3/49 (19 mm) 3/49 (19 mm) P() /4-PP P(P) /4-PP P() /8-PP P(P) /8-PP 5/ P45507-PP (51 mm) (8 mm) 31/169 3/89 75 P() /4-PP (78 mm) (9 mm) 31/169 3/89 75 P() /8-PP (78 mm) (9 mm) 31/169 3/89 75 P46069-PP (78 mm) (9 mm) ()=SPT (P)=SPP A A A Straight Flange ouplings Description Series A Part numer Straight oupling 50 21/49 (51 mm) (57 mm) (51 mm) P48157-PP Straight oupling 75 31/169 43/89 31/169 (78 mm) (111 mm) (78 mm) P48169-PP Reducer oupling 75/50 31/169 23/169 (78 mm) (56 mm) (51 mm) P45207-PP 90 Flange ouplings Description Series A Part numer 90 Elbow oupling 50 23/169 23/169 (51 mm) (56 mm) (56 mm) P48158-PP 90 Elbow oupling 75 31/169 23/169 31/89 (78 mm) (56 mm) (79 mm) P48168-PP 96

27 Flange Fittings A A A Threaded Flanges (Female) Description Series A Part numer 19 Female Pipe Thread 11/49 Female Pipe Thread 11/ Female Pipe Thread Flange lamps Note: O-ring included. 50 P()48154-PP (51 mm) (51 mm) 50 P()45512-PP (51 mm) (51 mm) 31/ P()46066-PP (78 mm) (51 mm) Description Series Part numer 2-Way Valve 3-Way Valve 2-Way Valve Stainless Steel Viton O-ring 2-Way Valve Stainless Steel Viton O-ring P7717-2/222-VI P VI ()=SPT Tee Flanges D Description Series A D Part numer Tee 43/89 27/89 (51 mm) (51 mm) (111 mm) (73 mm) P50193-PP 50 Narrow Tee 33/169 (51 mm) (51 mm) (81 mm) (51 mm) P55242-PP Reducer Tee 50/75 (51 mm) 31/169 (78 mm) 43/89 (111 mm) 27/89 (73 mm) P46717-PP Tee 75 31/169 (78 mm) 31/169 (78 mm) 43/89 (111 mm) 31/89 (79 mm) P46716-PP 450 Tee ody 75 31/169 (78 mm) 43/89 (111 mm) 31/49 (82 mm) P45251-PP 450 Tee ody (Narrow) 75 31/169 (78 mm) 31/89 (79 mm) 31/49 (82 mm) P55224-PP Note: There are no mounting provisions on the 50 series tee Mounting Kit Mounts to underside of tee and includes one extrusion and four screws. Mounting kit is not included with tees. Must be ordered separately. Also requires 5/169 or 8 mm bolt. Description Tee Mounting Kit (450 or 490 series manifold) Part number D Quick onnect Fittings A A Quick onnect Straight Hose arb Description Series A Part numer 1/ Straight Hose arb 3/49 Straight Hose arb 19 Straight Hose arb Quick onnect ap Quick onnect Plug Note: O-ring and clip included. Q 111/169 (43 mm) 111/169 (43 mm) 17/169 (36 mm) 21/49 (57 mm) 11/89 (28 mm) 15/169 (33 mm) 455-1/ / P 90 Quick onnect Hose arb Description Series A Part numer 1/ 90 Hose arb 3/49 90 Hose arb Hose arb Note: O-ring and clip included. Q 111/169 (43 mm) 219/649 (58 mm) 15/89 (41 mm) / / A A Quick onnection Outlet Description Series A Part numer Male Quick onnect Flanged Quick onnect Quick onnect 50 (51 mm) 13/169 (46 mm) P460-PP 3/49 (M) 15/169 (33 mm) (51 mm) P45527-NY 19 (M) 15/169 (33 mm) (51 mm) P45526-NY lip and O-Ring Description Retaining lip 302SS O-Ring (Viton ) Part numer P SS P VI 97

28 Electrical onnectors Note: Spraying Systems o. recommends the use of sealed connectors to improve reliability and prolong component life. PAKARD IDŐJÁRÁSI AMP MALE SOMAG FASTON ONNETOR TORONYSATLAKOZÓ (SZIGETELT) Note: No pin-out code needed with these connectors. HART 1: ONNETOR ODES AMP FEMALE FASTON ONNETOR Note: No pin-out code needed with these connectors. 2-PIN = ODE A 3-PIN = ODE J AMP FEMALE MATE-N-LOK ONNETOR (SEALED) 2-PIN = ODE 3-PIN = ODE K AMP MALE MATE-N-LOK ONNETOR (SEALED) Pin Pin 2 3 Pin Pin PIN or 3-PIN 2-PIN = ODE 3-PIN = ODE L PAKARD WEATHER PAK SHROUD ONNETOR (SEALED) 1 Pin 2 2-PIN = ODE E 3-PIN = ODE O 2-PIN = ODE D 3-PIN = ODE M PAKARD WEATHER PAK TOWER ONNETOR (SEALED) 1 Pin 2 2-PIN = ODE F 3-PIN = ODE P DEUTSH DT FEMALE ONNETOR (SEALED) DEUTSH DT MALE ONNETOR (SEALED) 1 Pin 2 A 1 Pin 2 A 2-PIN = ODE G PIN = ODE Q PAKARD METRIPAK FEMALE ONNETOR (SEALED) 2-PIN = ODE H 2 1 JST VH FEMALE ONNETOR (SEALED) 3-PIN = ODE R 3-PIN = ODE S PAKARD WEATHER PAK SHROUD ONNETOR (SEALED) PAKARD WEATHER PAK TOWER ONNETOR (SEALED) PIN = ODE I 3-PIN = ODE T 4-PIN 4-PIN = ODE U 4-PIN = ODE V ODE LETTER HART 2: PIN-OUT ODES ONNETOR POSITION ONNETOR POSITION ODE LETTER A OR 1 OR 2 OR 3 D OR 4 A OR 1 OR 2 OR 3 D OR 4 A R W P M P R W R W P N P R W R W P O P W R D R P W P P W R E R P W Q P R W F R P W R P W R G W R P S R W P H W R P T R P W I W P R U W R P J W P R V W P R K W R P W P R W This system is to be used for 344 and 356 ball valves and 440, 450, 460 and 490 ball valve manifolds equipped with electrical connectors. onnector and pin-outs are to be specified in valve or manifold part number when ordering. Note: On 2-pin connectors, only pin-out code or S is used. First: Specify code for connector desired (See hart 1). Second: Specify appropriate wire pin-out arrangement (See hart 2). Example: 356E-L Pin-out ode onnector ode Wire odes: R = Red (+12V) W = White (Switched) P = Plugged = lack (Ground) L W P R X P W R 98

29 2-Way Electrically Operated Solenoid Valves AA144P-, AA144A-, AA145H-, DirectoValve ontrol Valves n Direct acting; large internal flow chamber without pilot hole reduces chance of clogging. n Stainless steel wetted parts provide additional corrosion resistance. n Operate on 12 VD system. n Maximum pressure of 100 PSI (7 bar). n Encapsulated solenoid coil can be changed without removing valve from system. n EPDM diaphragms and seat washers, Viton optional. n ontinuous flow through bypass connection, with flow to spray line controlled by valve on-off action. AA144P AA144P-3 (Three Unit) AA144P DirectoValve ontrol Valves n 10 GPM (37.9 l/min) flow with only 5 PSI (0.34 bar) pressure drop. n 2.5 amp current draw. n Polypropylene body for chemical resistance. n Fabric reinforced Viton diaphragms and seat washers. AA()144P-* n No stroke adjustment required. n orrosion resistant, 430SS solenoid grade armature and armature stop. n Encapsulated coil and magnetic circuit. To order, specify AA144P- then 1, 2 or 3 to indicate number of units. Example: AA()144P-3 model number inlet size outlet size current draw 3/49 1/ 2.5 amp () = SPT Inlet AA144A-1 Spray Lines ontinuous ypass AA144A Valve for Pressures up to 100 PSI (7 bar) n 10 GPM (37.9 l/min) flow with only 5 PSI (0.34 bar) pressure drop. n an be ganged with other 144A DirectoValve control valves. n 2.5 amp current draw. n Polypropylene body for chemical resistance. n Fabric reinforced diaphragms. n Also available as 2- or 3-unit assembly. To order, specify AA144A- then 1, 2 or 3 to indicate number of units. Example: AA()144A-3 model number inlet size outlet size current draw AA144A-3 (Three Unit) AA()144A-* 3/49 1/ 2.5 amp () = SPT AA145H AA145H ontrol Valves n For pressures to 100 PSI (7 bar); 15 GPM (56.7 l/min) flow with 5 PSI (0.34 bar) pressure drop. n an be ganged with other 145H DirectoValve control valves. n 2.9 amp current draw. n Fiberglass reinforced Nylon body. Specify part number. Example: AA145H-1 model number inlet size outlet size current draw AA145H amp 99

30 3-Way Electrically Operated Solenoid Valves AA144P-1-3 AA144P-1-3 DirectoValve ontrol Valves The 144P-1-3 three-way solenoid-operated DirectoValve control valve was specifically designed to provide bypass control in spraying applications. When used with part number PP throttling valve or a 4916 metering orifice plate in the bypass line, it can provide for a constant pressure spray system. n For pressure to 65 PSI (4.5 bar). n 5 PSI (0.34 bar) pressure drop with 8 GPM (30 l/min) flow. n Fabric-reinforced Viton diaphragms. n Nylon encapsulated 12 VD coil with 1 49 Quick onnect terminals. n Power requirement 2.5 amp. n Glass-filled polypropylene (black) valve body. n Internal metal parts are stainless steel. n No stroke adjustment needed. n orrosion resistant, 430SS solenoid grade armature and armature stop. Specify part number. Example: AA()144P-1-3 Note: Throttling Valve not included. See page 104 for more information. Inlet Outlet 2 (regulated return flow to tank) AA144A-1-3 Outlet 1 (to spray line) ontinuous ypass AA144A-1-3 DirectoValve ontrol Valves The three-way solenoid-operated DirectoValve control valve bypasses boom flow to maintain constant spraying pressure when one or more boom sections are shut off. To maintain pressure with a Throttling Valve, Outlet 2 must be throttled to match the total capacity of the nozzles on that boom section. n For pressures to 65 PSI (4.5 bar). n 8 GPM (30 l/min) flow at only 5 PSI (0.34 bar) pressure drop. n 2.5 amp current draw. n Encapsulated 12 VD coil can be easily changed without removing valve from line. n Polypropylene body for chemical resistance. n Stainless steel internal metal parts. n hemical resistant EPDM diaphragms and seat washers. As with the 144A DirectoValve, the 144A-1-3 can be supplied as a 2-unit and 3-unit assembly. When ordering, specify 144A-2-3 or 144A-3-3. Note: Throttling Valve not included. See page 104 for more information. model number number of units in assembly spray line connection continuous flow inlet bypass connection AA()144P / 3/49 AA()144P / 3/49 AA()144P / 3/49 AA()144A / 3/49 AA144A-3-3 (Three Unit) AA144P-3-3 (Three Unit) AA()144A AA()144A / 1/ 3/49 3/49 () = SPT Solenoid Foam Marker Valves AA144F-1-3 TeeJet AA144F-1-3 DirectoValve Solenoid Valve for Foam Markers The 144F-1-3 three-way operated DirectoValve was designed for use with foam markers. With electrical power off, flow to Outlet 1 is stopped and liquid flows to Outlet 2. With electrical power on, flow to Outlet 2 is stopped and liquid flows to Outlet 1. Features: n Operating pressure range of 0 50 PSI (0 3.5 bar). n Large flow capacities, 5 PSI (0.34 bar) pressure drop with 8 GPM (30 l/min) flow. n Nylon encapsulated 12 VD coil with 1 49 Quick onnect terminals. n Glass filled polypropylene (black) valve body. n Internal metal parts are made of brass, fasteners are made of stainless steel, other metal parts are zinc-plated. n hemical resistant EPDM rubber seat washer and diaphragm. AA144F

31 340 Series 2-Way Manual Shutoff all Valves 344M-NY 2-Way Nylon Manual all Valves n Quarter turn of handle from shutoff to full flow. n 3/49 or 19 NPT and SPT (F) connection. AA()344M-NY n Wetted parts: Nylon, Teflon, polypropylene and Viton. Specify valve number. Example: AA()344M-2-1 valve number maximum pressure number of outlets connection size AA()344M-NY AA()344M-2-3/4 300 PSI 1 AA()344M-2-1 (20 bar) 1 Flow Rate: 5 PSI (0.34 bar) pressure drop for 32 GPM (121 l/min) flow. 3/49 19 () = SPT 340M-PP Series 2-Way Manual all Valves n Quarter turn of handle from shutoff to full flow. n 3/89, 1/, 3/49, 19, 11/49 or 11/ NPT and SPT (F) connection. AA()343M-PP n Wetted parts: glass-reinforced polypropylene, Teflon and Viton. Specify valve number. Example: AA()343M-2-3/8-PP valve number maximum pressure number of outlets connection size AA()343M-PP AA()343M-2-3/8-PP 150 PSI 1 AA()343M-2-1/2-PP (10 bar) 1 3/89 1/ Flow Rate: 5 PSI (0.34 bar) pressure drop for 11 GPM (42 l/min) flow. () = SPT Specify valve number. Example: AA()344M-2-3/4-PP AA()344M-PP valve number maximum pressure number of outlets connection size AA()344M-2-3/4-PP 125 PSI 1 AA()344M-2-1-PP (9 bar) 1 Flow Rate: 5 PSI (0.34 bar) pressure drop for 32 GPM (121 l/min) flow. 3/49 19 () = SPT AA()344M-PP Specify valve number. Example: AA()346M-2-1-1/4-PP AA()346M-PP valve number maximum pressure number of outlets connection size AA()346M-2-1-1/4-PP 125 PSI 1 AA()346M-2-1-1/2-PP (9 bar) 1 Flow Rate: 5 PSI (0.34 bar) pressure drop for 100 GPM (322 l/min) flow. 11/49 11/ () = SPT AA()346M-PP 101

32 340 Series 3-Way Manual ypass all Valves 344M-NY 3-Way Nylon Manual all Valves n 3-way version diverts flow to either outlet; no shutoff. n 3/49 or 19 NPT and SPT (F) connection. AA()344M-NY n Wetted parts: Nylon, virgin Teflon, polypropylene and Viton. Specify valve number. Example: AA()344M-3-1 valve number maximum pressure number of outlets connection size AA()344M-NY AA()344M-3-3/4 300 PSI 2 AA()344M-3-1 (20 bar) 2 Flow Rate: 5 PSI (0.34 bar) pressure drop for 24 GPM (91 l/min) flow. 3/49 19 () = SPT 340M-PP Series 3-Way Manual all Valves n 3-way version diverts flow to either outlet; no shutoff. n 3/89, 1/, 3/49, 19, 11/49 or 11/ NPT and SPT (F) connection. AA()343M-PP n Wetted parts: glass-reinforced polypropylene, virgin Teflon and Viton. Specify valve number. Example: AA()343M-3-3/8-PP valve number maximum pressure number of outlets connection size AA()343M-PP AA()343M-3-3/8-PP 150 PSI 2 AA()343M-3-1/2-PP (10 bar) 2 Flow Rate: 5 PSI (0.34 bar) pressure drop for 8 GPM (30 l/min) flow. 3/89 1/ () = SPT Specify valve number. Example: AA()344M-3-3/4-PP AA()344M-PP valve number maximum pressure number of outlets connection size AA()344M-3-3/4-PP 125 PSI 2 AA()344M-3-1-PP (9 bar) 2 Flow Rate: 5 PSI (0.34 bar) pressure drop for 24 GPM (91 l/min) flow. 3/49 NPT or SPT 19 NPT or SPT () = SPT AA()344M-PP Specify valve number. Example: AA()346M-3-1-1/4-PP AA()346M-PP valve number maximum pressure number of outlets connection size AA()346M-3-1-1/4-PP 125 PSI 2 AA()346M-3-1-1/2-PP (9 bar) 2 Flow Rate: 5 PSI (0.34 bar) pressure drop for 64 GPM (242 l/min) flow. 11/49 11/ () = SPT AA()346M-PP 102

33 Manual Pressure Relief/Regulating Valves Piston-Type Pressure Relief/Regulating Valves ypasses excess liquid. Adjustable to maintain control of line pressure at any pressure within the valve s operating range. Selected pressure setting firmly held in place by locknut. Extra large valve passages to handle large flows. Model n 302 stainless steel spring and EPDM O-ring. n Excellent chemical resistance. n 1/49 port for pressure gauge pipe plug included. Model 23120A n Same as but with 316SS spring and Viton O-ring. Specify valve number. Example: () /2-PP Model Model 6815 valve number inlet & pipe connections material pressure range ()23120-*-PP ()23120A-*-PP ()23120-*-PP-60 ()23120-*-PP-60-VI *Specify pipe size. Model 6815 n Other models for high pres sures up to 1,200 PSI (82 bar) are also available. n rass also available with hardened stainless steel seat. 1/ or 3/49 Polypropylene 150 PSI (10 bar) 1/ or 3/49 Polypropylene 150 PSI (10 bar) 1/ or 3/49 Polypropylene 60 PSI (4 bar) 1/ or 3/49 Polypropylene/Viton 60 PSI (4 bar) () = SPT Specify valve number. Example: ()6815-1/2-50 valve number inlet & pipe connections material pressure range ()6815-*-50 ()6815-*-300 ()6815-*-700 *Specify pipe size. 1/ or 3/49 rass or Aluminum 50 PSI (3.5 bar) 1/ or 3/49 rass or Aluminum 300 PSI (20 bar) 1/ or 3/49 rass or Aluminum 700 PSI (48 bar) () = SPT Model 110 n Removable bonnet for servicing unit without removing valve from line. Specify valve number. Example: AA()110-1/4-300 valve number inlet & pipe connections material pressure range AA()110-*-300 AA()110-*-700 AA() /49 or 3/89 rass 300 PSI (20 bar) 1/49 or 3/89 rass 700 PSI (48 bar) 19 rass, Aluminum or Ductile Iron 150 PSI (10 bar) Model 110-1/4 and 110-3/8 Model 8460 Model 110-1, /4 and /2 AA() /4 AA() /2 *Specify pipe size. Model 8460 Diaphragm-Type Pressure Relief/Regulating Valves n Flow rate to 56 GPM (212 l/min) for 1/ and 70 GPM (265 l/min) for 3/49. n Stainless steel springs, responsive to the pressure range of each valve. n Extra large valve passages to handle full flow from supply line. 11/49 rass, Aluminum or Ductile Iron 150 PSI (10 bar) 11/ rass, Aluminum or Ductile Iron 150 PSI (10 bar) n Positive locknut to hold adjustment screw firmly in place. Not affected by jarring and vibration. Specify valve number. Example: /2-50 () = SPT Valve NUMber inlet & pipe connections inlet body material bonnet pressure range 8460-* * *Specify pipe size. 1/ or 3/49 Nylon Aluminum 50 PSI (3.5 bar) 1/ or 3/49 Nylon Aluminum 300 PSI (20 bar) 103

34 Manual ontrol Valve Model 6 n Molded of corrosion resistant materials; all wetted parts are polypropylene, stainless steel and polyethylene. n Maximum pressure of 150 PSI (10 bar). n Large capacity, 12 GPM (47 l/min) at 5 PSI (0.34 bar) pressure drop. n Molded-in mounting flange and 1/49 NPT gauge port. n Valves can be ganged together using hex nipple for multiple boom control. n Easily repaired without removing valve from spray line. Example: AA()6 () = SPT 3/49 Inlet onnections Molded-in Gauge Port 1/ oom onnection ontrol Valves For Selective ontrol of Three-Section oom Sprayers at Pressures up to 300 PSI (20 bar). n Use to open any of three boom section lines in any desired combination. n Raise lever to open, lower lever to close the valve without changing the indexed position. A Index Setting 1/49 NPT Pressure Gauge Port Side connection for bypass and pressure relief valve is interchangeable with spray gun connection. n Aluminum construction with stainless steel and plastic internal parts for maximum corrosion resistance. Example: AA17Y Model AA17 model number material maximum pressure inlet (3) boom outlets accessory outlet AA17Y AA17L Aluminum, Polymer, SS 300 PSI (20 bar) 19 NPT 3/49 (F) 3/49 (F) Aluminum, Polymer, SS 300 PSI (20 bar) 3/49 NPT 3/49 (F) 3/49 (F) Throttling Valves For regulating flow in systems equipped with centrifugal pumps where sensitive regulation is required or to control flow in jet agitator return lines. Locknut holds pressure setting firmly in place. Type n Polypropylene con struction for excellent chemical resistance. n Pressures to 150 PSI (10 bar). n 1/ and 3/49 NPT or SPT connections. n 10 PSI (0.6 bar) pressure drop at 6 GPM (37.8 l/min) flow rate for 1/; 18 GPM (69 l/min) for 3/49 size. Example: () /2-PP () = SPT Type n Pressures to 125 PSI (9 bar). n onstructed of Nylon, elcon, aluminum, steel and stainless steel. n hoice of 1/ or 3/49 NPT connections. n Maximum flow rate at 100 PSI (7 bar) is 56 GPM (212 l/min) for 1/ size and 82 GPM (310 l/min) for 3/49 size. Example: /2-NY Type n Pressures to 150 PSI (10 bar). n Available in brass, aluminum or ductile iron. n hoice of 19, 11/49 or 11/ NPT connections. n Flow rate at 40 PSI (3 bar) is 116 GPM (440 l/min) for 19 and 11/49 sizes and 172 GPM (651 l/min) for 11/ size. Example: