GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS SECURITY SYSTEM KIT CONTENTS SHOCK SENSOR F-D15 WINDOW DECAL (QTY 2) F-D16

Transcription

1 GENUINE ACCESSRIES INSTALLATIN INSTRUCTINS PART NUMBER: F-N03 NTE: NT CMPATIBLE WITH REMTE START SYSTEM, PART# F-N02 SECURITY SYSTEM KIT CNTENTS APPLICABLE MDELS: 2007>MAZDA CX-9 WITHUT ADVANCED KEYLESS ENTRY SYSTEM WALLET CARD CNTRL MDULE F-D11A SHCK SENSR F-D15 WNER S MANUAL & WALLET CARD (QTY 1) SECURITY L.E.D F-D19 LNG WIRE TIE (QTY 3) EMERGENCY VERRIDE BUTTN F-Z03 WINDW DECAL (QTY 2) F-D16 SHRT WIRE TIE (QTY 10) SHCK SENSR HARNESS IDC WIRE TAP (QTY 6) WIRE HARNESS F-N19 0 TLS REQUIRED SAFETY GLASSES FIBER STICK #2 PHILLIPS SCREWDRIVER SMALL FLAT TIP SCREWDRIVER 1/4 DRIVE RATCHET 1/4 DRIVE 10 MM SCKET 1/4 DRIVE TRQUE WRENCH PLIERS WIRE CUTTERS CENTER PUNCH PWER DRILL 9/32 DRILL BIT UTILITY KNIFE 0 VEHICLE PREPARATIN 1. CLEAN HANDS 2. PEN DRIVER S DR WINDW 3. RECRD RADI STATIN PRESETS 4. SET PARKING BRAKE 5. SLIDE DRIVER SEAT T REAR MST PSITIN 6. VEHICLE MUST BE AT RM TEMPERATURE 1

2 0 ELECTRICAL SYSTEM GENERAL PRCEDURES Wire color code Two-color wires are indicated by a two-letter symbol.the first indicates the base color of the wire, the second the color of the stripe. For example: W/R is a white wire with a red strip BR/Y is a brown wire with a yellow strip Symbol (Example) Solid color wire Striped wire Connector diagrams Connector diagrams show connectors on the harness side. The terminal indicates the view from the harness side. (Example) Connector on harness side B Black W/R White (base color) View from harness side Red(stripe) Unused terminals are indicated by. Disconnecting Connectors When disconnecting connector, grasp the connectors, not the wires. N GD D Locking Connector When locking connectors, listen for a click indicating they are securely locked. Wire Tap Procedure Place Wire Tap on the vehicle wire and close by squeezing the pliers. 2

3 1 DISCNNECT THE BATTERY 1. DISCNNECT AND ISLATE THE NEGATIVE BATTERY CABLE. (FIGURE A) 10 mm Socket FIGURE A 2 REMVE DRIVER S SCUFF PLATE AND LEFT KICK PANEL 1. USING A FIBER STICK, REMVE THE DRIVER S SIDE SCUFF PLATE. THE SCUFF PLATE IS HELD BY (3) CLIPS. (FIGURE B) FIGURE B Plastic Nut 2. REMVE THE DRIVER S SIDE KICK PANEL BY REMVING THE PLASTIC NUT. (FIGURE C) PARTIALLY PEEL BACK THE RUBBER WEATHERSTRIP AWAY FRM THE KICK PANEL. INSERT A FIBER STICK BETWEEN THE BDY AND KICK PANEL T DISENGAGE THE RETAINING CLIP. GENTLY PULL THE KICK PANEL TWARD THE CENTER F THE VEHICLE T REMVE. FIGURE C 3 MUNT THE EMERGENCY VERRIDE BUTTN 1. LCATE THE PREVIUSLY REMVED DRIVER S KICK PANEL. 2. CENTER PUNCH THE DRIVER S KICK PANEL, EXACTLY 12 mm DWN FRM THE TP AND 95 mm LEFT F THE FAR EDGE. (FIGURE D) 3. CAREFULLY DRILL A 9/32 DIAMETER HLE AT THE CENTER PUNCHED LCATIN. 4. DISCNNECT THE EMERGENCY VERRIDE BUTTN FRM THE SECURITY HARNESS BY UNPLUGGING THE TW 2-PIN WHITE CNNECTRS. 5. REMVE THE CVERED NUT AND LCK WASHER FRM THE EMERGENCY VERRIDE BUTTN AND INSERT THE BUTTN THRUGH THE DRILLED HLE FRM THE BACK SIDE F THE DRIVER S SIDE KICK PANEL. NTE: DISCARD THE LCK WASHER, IT IS NT USED N THIS MDEL. FIGURE D 6. REPLACE THE LCK CVERED NUT AND CAREFULLY TIGHTEN BY HAND.! CAUTIN: D NT VERTIGHTEN CVERED NUT. 3

4 4 REMVE STEERING CLUMN CVERS 1. REMVE THE (3) PHILLIPS HEAD SCREWS FRM THE LWER STEERING CLUMN CVER. (FIGURE E) 2. INSERT A FIBER STICK BETWEEN THE CMBINATIN SWITCH AND THE LWER CVER. GENTLY RTATE THE FIBER STICK UNTIL THE TP AND BTTM CVERS SEPERATE. (FIGURE E) 3. IF EQUIPPED, GENTLY UNCLIP THE IGNITIN KEY LIGHT AND REMVE BTH TP AND BTTM CVERS AND SET ASIDE WHERE THEY CANNT BE DAMAGED.! CAUTIN: BE CAREFUL NT T DAMAGE PLASTIC CVERS. FIGURE E 5 MUNT THE DASH LED STATUS INDICATR Upper Steering Column Cover 1. LCATE THE PREVIUSLY REMVED UPPER STEERING CLUMN CVER. (FIGURE F) 2. CENTER PUNCH THE AREA NEAR THE CMBINATIN SWITCH F THE UPPER STEERING CLUMN CVER 15 mm FRM INSIDE EDGE F THE CMBINATIN SWITCH PENING AND 15 mm FRM THE BTTM EDGE F THE UPPER STEERING CLUMN CVER. (FIGURE F) 3. CAREFULLY DRILL A 9/32 DIAMETER HLE IN THE UPPER STEERING CLUMN CVER AT THE CENTER PUNCHED LCATIN. 15 mm 15 mm! CAUTIN: BE SURE NT T DRILL THE HLE VERSIZED. 4. PASS THE LED CNNECTR AND WIRES THRUGH THE DRILLED HLE FRM THE FRNT SIDE F UPPER STEERING CLUMN CVER. PRESS THE LED INT THE HLE FIRMLY UNTIL FULLY SEATED. 5. PSITIN UPPER STEERING CLUMN CVER IN FACTRY MUNTING LCATIN. D NT REINSTALL LWER STEERING CLUMN CVER AT THIS TIME. FIGURE F Lower Steering Column Cover 6 REMVE LWER DASH PANEL 1. USING A SMALL FLAT TIP SCREWDRIVER, REMVE (2) PLASTIC FASTNERS. 2. REMVE THE BLACK LWER DASH PANEL BY DISENGAGING THE SINGLE CLIP LCATED AT THE FRNT, CENTER F THE PANEL. (FIGURE G) FIGURE G 4

5 7 MUNT THE CNTRL MDULE 1. LCATE THE 24-PIN CNNECTR N THE SECURITY SYSTEM HARNESS AND ATTACH IT T THE MATING 24-PIN CNNECTR N THE SECURITY SYSTEM MDULE. 2. LCATE THE 5-PIN CNNECTR N THE SHCK SENSR HARNESS AND ATTACH IT T THE MATING 5-PIN CNNECTR N THE SECURITY SYSTEM MDULE. NTE: BE SURE T ENGAGE THE 5-PIN CNNECTR FRM THE SHCK SENSR HARNESS T THE SECURITY MDULE, NT THE 4-PIN CNNECTR. Wire Ties x 3 Body Control Module 3. PSITIN THE SECURITY MDULE ABVE THE MAIN HARNESS RUNNING ABVE THE BDY CNTRL MDULE, IN THE LEFT KICK PANEL AREA. (FIGURE H) 4. USING (3) F THE SUPPLIED WIRE TIES, SECURE THE SECURITY MDULE T THE MAIN HARNESS USING THE EYELETS N EACH SIDE F THE SECURITY MDULE. 5. BE SURE WIRE TIES ARE TIGHTENED CMPLETELY, THEN TRIM FF EXCESS. 8 MUNT THE SHCK SENSR MDULE 1. PSITIN THE SHCK SENSR MDULE N THE VEHICLE HARNESS LCATED T THE LEFT F THE STEERING CLUMN. (FIGURE I) 2. ATTACH A SUPPLIED, SHRT WIRE TIE THRUGH THE TP MUNTING HLE IN THE SHCK SENSR MDULE AND ARUND THE MAIN HARNESS. FIGURE H Shock Sensor Harness Vehicle Harness 3. REPEAT STEP 2 FR THE BTTM MUNTING HLE IN THE SHCK SENSR MDULE. 4. BE SURE BTH WIRE TIES ARE TIGHTENED CMPLETELY, THEN TRIM FF EXCESS. 5. LCATE THE 4-PIN CNNECTR N THE SHCK SENSR HARNESS AND ATTACH IT T THE MATING 4-PIN CNNECTR N THE SHCK SENSR MDULE. 9 GRUND CNNECTIN 1. LCATE THE 10 MM FACTRY BLT, MUNTED HIGH UP UNDER THE DASH, NEAR THE VEHICLE DASHWALL, SUPPRTING THE FACTRY UNIT - LIGHT AUT FF MDULE. (FIGURE J) 2. USING A 10 MM SCKET AND RATCHET, REMVE THE 10 MM BLT. 3. USING THE 10 MM BLT JUST REMVED, SECURE THE REMTE START HARNESS BLACK GRUND WIRE WITH RINGLET AND TIGHTEN WITH A 10 MM SCKET AND RATCHET. Steering Column FIGURE I Steering Column Unit-Light Auto ff Module 10 mm Factory Bolt NTE: USING A 1/4 DRIVE TRQUE WRENCH, MAKE SURE THAT THE 10 MM GRUND BLT IS SECURELY TIGHTENED T INCH/PUNDS. FIGURE J 5

6 10 IGNITIN SWITCH CNNECTINS 1. RUTE THE SECURITY HARNESS WITH 6-PIN MALE AND FEMALE IGNITIN CNNECTRS WITH RED SECNDARY LCK ALNG THE LEFT SIDE F THE STEERING CLUMN. Connector #C LCATE THE 6-PIN WHITE IGNITIN CNNECTR, N THE LEFT SIDE F THE STEERING CLUMN. 6 Pin Male 3. RELEASE THE RED SECNDARY LCK AND DISCNNECT THE 6-PIN WHITE IGNITIN CNNECTR BY PULLING UTWARD. (! CAUTIN: D NT PULL N WIRES T DISCNNECT CNNECTR.) 4. PLUG THE SECURITY HARNESS 6-PIN FEMALE CNNECTR INT THE FACTRY IGNITIN SWITCH AND ENGAGE THE RED SECNDARY LCK. (FIGURE K) 5. CNNECT THE SECURITY HARNESS 6-PIN MALE CNNECTR INT THE FACTRY IGNITIN SWITCH HARNESS CNNECTR AND ENGAGE THE RED SECNDARY LCK. (FIGURE K) FIGURE K 6 Pin Female 11 CNNECT THE LED STATUS INDICATR 1. LCATE THE 2-PIN BLACK CNNECTR N THE SECURITY HARNESS. 2. RUTE THE 2-PIN BLACK CNNECTR AND WIRE HARNESS NEXT T THE SECURITY HARNESS ALNG THE LEFT SIDE F THE STEERING CLUMN AND SECURE WITH SUPPLIED WIRE TIES. 3. LCATE THE 2-PIN BLACK CNNECTR FRM THE LED HARNESS, WHICH WAS PREVIUSLY MUNTED IN THE UPPER STEERING CLUMN CVER, AND PLUG IT INT THE 2-PIN BLACK CNNECTR FRM THE SECURITY HARNESS. (FIGURE L) SECURITY HARNESS FIGURE L LED HARNESS 12 PARKING LIGHT CNNECTIN 17-PIN 1. LCATE THE 17-PIN WHITE CNNECTR PLUGGED INT THE MULTIFUNCTIN SWITCH N THE LEFT SIDE F THE STEERING CLUMN. (FIGURE M) 2. USING A RAZR KNIFE, CAREFULLY CUT BACK 1-2 F THE ELECTRICAL TAPE T EXPSE THE WIRING. (! CAUTIN: BE EXTREMELY CAREFUL NT T DAMAGE ANY F THE WIRES.) 3. USING (1) SUPPLIED WIRE TAP, CNNECT THE WIRE LISTED BELW AND CRIMP THE WIRE TAP IN PLACE USING PLIERS. ENSURE THAT A CMPLETE AND SECURE CNNECTIN IS MADE. REFER T FIGURE M & N FR PRPER CNNECTR AND PIN LCATIN. FIGURE M FIGURE N Connector # VIEW FRM HARNESS SIDE VEHICLE S PARKING LIGHT WIRE SECURITY HARNESS WIRE BRWN BRWN/WHITE NTE: REFER T PAGE 2 FR WIRE TAP PRCEDURE AND WIRE CLR CDE INFRMATIN. 6

7 13 BDY CNTRL MDULE CNNECTINS 1. LCATE THE 30-PIN, 6-PIN, 16-PIN AND THE 24-PIN CNNECTRS AT THE BDY CNTRL MDULE LCATED IN THE DRIVER S KICK PANEL. (FIGURE ) 16-PIN Connector # E 30-PIN Connector # C 6-PIN Connector # D FIGURE 24-PIN Connector # F 14 HRN CNNECTIN 1. LCATE THE 30-PIN CNNECTR AT THE BDY CNTRL MDULE IN THE DRIVER S KICK PANEL. (FIGURE ) Connector # C 2. USING A RAZR KNIFE, CAREFULLY CUT BACK 1-2 F THE ELECTRICAL TAPE T EXPSE THE WIRING. (! CAUTIN: BE EXTREMELY CAREFUL NT T DAMAGE ANY F THE WIRES.) 3. USING (1) SUPPLIED WIRE TAP, CNNECT THE WIRE LISTED BELW AND CRIMP THE WIRE TAP IN PLACE USING PLIERS. ENSURE THAT A CMPLETE AND SECURE CNNECTIN IS MADE. REFER T FIGURE & P FR PRPER CNNECTR AND PIN LCATIN. FIGURE P VIEW FRM HARNESS SIDE VEHICLE S HRN WIRE GREEN/RED SECURITY HARNESS WIRE GREEN/RED NTE: REFER T PAGE 2 FR WIRE TAP PRCEDURE AND WIRE CLR CDE INFRMATIN. 15 DR TRIGGER CNNECTIN 1. LCATE THE 6-PIN CNNECTR AT THE BDY CNTRL MDULE IN THE DRIVER S KICK PANEL. (FIGURE ) Connector # D 2. USING A RAZR KNIFE, CAREFULLY CUT BACK 1-2 F THE ELECTRICAL TAPE T EXPSE THE WIRING. (! CAUTIN: BE EXTREMELY CAREFUL NT T DAMAGE ANY F THE WIRES.) 3. USING (1) SUPPLIED WIRE TAP, CNNECT THE WIRE LISTED BELW AND CRIMP THE WIRE TAP IN PLACE USING PLIERS. ENSURE THAT A CMPLETE AND SECURE CNNECTIN IS MADE. REFER T FIGURE & Q FR PRPER CNNECTR AND PIN LCATIN. FIGURE Q VIEW FRM HARNESS SIDE VEHICLE S DR TRIGGER WIRE SECURITY HARNESS WIRE YELLW/RED YELLW/RED NTE: REFER T PAGE 2 FR WIRE TAP PRCEDURE AND WIRE CLR CDE INFRMATIN. 7

8 16 ARM CNNECTIN 1. LCATE THE 16-PIN CNNECTR AT THE BDY CNTRL MDULE IN THE DRIVER S KICK PANEL. (FIGURE ) Connector # E 2. USING A RAZR KNIFE, CAREFULLY CUT BACK 1-2 F THE ELECTRICAL TAPE T EXPSE THE WIRING. (! CAUTIN: BE EXTREMELY CAREFUL NT T DAMAGE ANY F THE WIRES.) 3. USING (1) SUPPLIED WIRE TAP, CNNECT THE WIRE LISTED BELW AND CRIMP THE WIRE TAP IN PLACE USING PLIERS. ENSURE THAT A CMPLETE AND SECURE CNNECTIN IS MADE. REFER T FIGURE & R FR PRPER CNNECTR AND PIN LCATIN. VEHICLE S ARM WIRE SECURITY HARNESS WIRE RED NTE: REFER T PAGE 2 FR WIRE TAP PRCEDURE AND WIRE CLR CDE INFRMATIN. FIGURE R VIEW FRM HARNESS SIDE RED 17 DISARM CNNECTIN 1. LCATE THE 16-PIN CNNECTR AT THE BDY CNTRL MDULE IN THE DRIVER S KICK PANEL. (FIGURE ) Connector # E 2. USING A RAZR KNIFE, CAREFULLY CUT BACK 1-2 F THE ELECTRICAL TAPE T EXPSE THE WIRING. (! CAUTIN: BE EXTREMELY CAREFUL NT T DAMAGE ANY F THE WIRES.) 3. USING (1) SUPPLIED WIRE TAP, CNNECT THE WIRE LISTED BELW AND CRIMP THE WIRE TAP IN PLACE USING PLIERS. ENSURE THAT A CMPLETE AND SECURE CNNECTIN IS MADE. REFER T FIGURE & S FR PRPER CNNECTR AND PIN LCATIN. VEHICLE S DISARM WIRE SECURITY HARNESS WIRE RED/YELLW NTE: REFER T PAGE 2 FR WIRE TAP PRCEDURE AND WIRE CLR CDE INFRMATIN. FIGURE S VIEW FRM HARNESS SIDE RED/YELLW 18 LIFTGATE TRIGGER CNNECTIN 1. LCATE THE 24-PIN CNNECTR AT THE BDY CNTRL MDULE IN THE DRIVER S KICK PANEL. (FIGURE ) 2. USING A RAZR KNIFE, CAREFULLY CUT BACK 1-2 F THE ELECTRICAL TAPE T EXPSE THE WIRING. (! CAUTIN: BE EXTREMELY CAREFUL NT T DAMAGE ANY F THE WIRES.) 3. USING (1) SUPPLIED WIRE TAP, CNNECT THE WIRE LISTED BELW AND CRIMP THE WIRE TAP IN PLACE USING PLIERS. ENSURE THAT A CMPLETE AND SECURE CNNECTIN IS MADE. REFER T FIGURE & T FR PRPER CNNECTR AND PIN LCATIN. FIGURE T Connector # F VIEW FRM HARNESS SIDE VEHICLE S LIFTGATE TRIGGER WIRE SECURITY HARNESS WIRE LT. GREEN/RED LT. GREEN/RANGE NTE: REFER T PAGE 2 FR WIRE TAP PRCEDURE AND WIRE CLR CDE INFRMATIN. 8

9 19 CNNECT THE EMERGENCY VERRIDE BUTTN AND REPLACE DRIVER S KICK PANEL 1. LCATE THE 2-PIN WHITE CNNECTR N THE SECURITY HARNESS. 2. LCATE THE 2-PIN WHITE CNNECTR FRM THE EMERGENCY VERRIDE BUTTN, WHICH WAS PREVIUSLY MUNTED IN THE DRIVER S KICK PANEL, AND PLUG IT INT THE 2-PIN WHITE CNNECTR FRM THE SECURITY HARNESS. (FIGURE U) SECURITY HARNESS BUTTN HARNESS FIGURE U 3. RE-INSTALL THE DRIVER S KICK PANEL BY ENGAGING THE RETAINING CLIP N THE PANEL. RE-INSTALL THE PLASTIC RETAINER AND REPLACE THE WEATHERSTRIP. (FIGURE V) Plastic Nut FIGURE V 20 SYSTEM PWER-UP 1. VERIFY THAT ALL CNNECTINS ARE SECURE AS PER INSTALLATIN INSTRUCTINS. NTE: BE SURE THE RM FUSE IS INSTALLED IN THE FUSE PANEL. 2. RECNNECT THE NEGATIVE BATTERY TERMINAL. 3. IF THE HRN IS BEEPING AND THE PARKING LIGHTS FLASHING, TURN THE IGNITIN T THE N PSITIN AND PRESS THE EMERGENCY VERRIDE BUTTN LCATED N THE DRIVER S KICK PANEL T DISARM THE SYSTEM. 4. ENSURE THE IGNITIN IS IN THE FF PSITIN BEFRE PRCEDING T THE FUNCTIN TEST. 9

10 21 FUNCTIN TEST 1. CLSE ALL DRS, THEN PRESS THE LCK BUTTN N THE KEYLESS ENTRY TRANSMITTER T LCK ALL DRS AND ARM THE SECURITY SYSTEM. a. THE HRN BEEPS (1) TIME. b. THE PARKING LIGHTS FLASH (1) TIME. c. THE RED LED STATUS INDICATR BEGINS BLINKING (@ 1 BLINK PER SECND). 2. MANUALLY UNLCK AND PEN THE DRIVER S DR. a. THE HRN BEEPS N AND FF. b. THE PARKING LIGHTS FLASH N AND FF. c. THE RED LED FLASHES (3) TIMES...PAUSE AND REPEATS CNTINUALLY. 3. PRESS THE UNLCK BUTTN N THE KEYLESS ENTRY TRANSMITTER T DISARM THE SECURITY SYSTEM. a. THE HRN BEEPS (4) TIMES. b. THE PARKING LIGHTS FLASH (4) TIMES. c. THE RED LED FLASHES (3) TIMES...PAUSE AND REPEATS CNTINUALLY. 4. TURN THE IGNITIN T THE RUN PSITIN, THEN BACK T THE FF PSITIN. REMVE THE KEY, IF APPLICABLE. a. THE RED LED TURNS FF. 5. CLSE ALL DRS, THEN LCK THE DRS USING THE DRIVER S SIDE DR KEY CYLINDER T ARM THE SECURITY SYSTEM. a. THE HRN BEEPS (1) TIME. b. THE PARKING LIGHTS FLASH (1) TIME. c. THE RED LED STATUS INDICATR BEGINS BLINKING (@ 1 BLINK PER SECND). 6. USE THE DRIVER S DR KEY CYLINDER T UNLCK THE DRIVER S DR. a. THE HRN BEEPS (2) TIMES. b. THE PARKING LIGHTS FLASH (2) TIMES. c. THE RED LED STATUS INDICATR TURNS FF. 7. ENTER THE VEHICLE AND CLSE THE DRIVER S DR. 8. PRESS THE LCK BUTTN N THE KEYLESS ENTRY TRANSMITTER T ARM THE SECURITY SYSTEM. a. THE HRN BEEPS (1) TIME. b. THE PARKING LIGHTS FLASH (1) TIME. c. THE RED LED STATUS INDICATR BEGINS BLINKING (@ 1 BLINK PER SECND). 9. ATTEMPT T START THE VEHICLE BY TURNING THE IGNITIN T THE START PSITIN. a. THE STARTER WILL NT ENGAGE. 10. TURN THE IGNITIN T THE RUN PSITIN, PRESS THE EMERGENCY VERRIDE BUTTN AND RE-ATTEMPT T START THE VEHICLE. a. THE SECURITY SYSTEM DISARMS AND THE VEHICLE STARTS. 11. TURN THE IGNITIN T THE FF PSITIN AND PRESS THE LCK BUTTN N THE KEYLESS ENTRY TRANSMITTER T ARM THE SECURITY SYSTEM. a. THE HRN BEEPS (3) TIMES. b. THE PARKING LIGHTS FLASH (3) TIME. c. THE RED LED STATUS INDICATR BEGINS BLINKING (3 BLINKS IN A RW). 12. MANUALLY UNLCK AND PEN THE PASSENGER S DR. a. THE HRN BEEPS N AND FF. b. THE PARKING LIGHTS FLASH N AND FF. c. THE RED LED FLASHES 3 TIMES...PAUSE AND REPEATS CNTINUALLY. 10

11 22 FUNCTIN TEST (CNTINUED) 13. PRESS THE UNLCK BUTTN N THE KEYLESS ENTRY TRANSMITTER T DISARM THE SECURITY SYSTEM. a. THE HRN BEEPS (4) TIMES. b. THE PARKING LIGHTS FLASH (4) TIMES. c. THE RED LED FLASHES 3 TIMES...PAUSE AND REPEATS CNTINUALLY. 14. TURN THE IGNITIN T THE RUN PSITIN, THEN BACK T THE FF PSITIN. REMVE THE KEY, IF APPLICABLE. a. THE RED LED TURNS FF. 15. EXIT THE VEHICLE, CLSE ALL DRS, THEN PRESS THE LCK BUTTN N THE KEYLESS ENTRY TRANSMITTER T LCK ALL DRS AND ARM THE SECURITY SYSTEM. a. THE HRN BEEPS (1) TIME. b. THE PARKING LIGHTS FLASH (1) TIME. c. THE RED LED STATUS INDICATR BEGINS BLINKING (@ 1 BLINK PER SECND). 23 SETTING THE SHCK SENSR SENSITIVITY 1. WAIT 10 SECNDS, USING AN PEN HAND, LIGHTLY SLAP THE PASSENGER SIDE A-PILLAR USING APPRXIMATE FRCE F A BASKETBALL BUNCING AGAINST THE VEHICLE. a. HRN BEEPS (7) TIMES. 2. WAIT 10 SECNDS, USING AN PEN HAND, LIGHTLY SLAP THE DRIVER S SIDE A-PILLAR USING APPRXIMATE FRCE F A BASKETBALL BUNCING AGAINST THE VEHICLE. a. HRN BEEPS (7) TIMES. ATTENTIN!!! IF THE ALARM TRIGGERED DURING EITHER STEP 1 R 2, THE SENSITIVITY F THE SHCK SENSR MUST BE TURNED DWN. USE A SMALL FLAT TIP SCREWDRIVER AND TURN THE SENSITIVITY KNB N THE SHCK SENSR IN A CUNTERCLCKWISE DIRECTIN, THEN RE-TEST. (FIGURE W) SHCK SENSR ADJUSTMENT 1= LEAST SENSITIVE 7= MST SENSITIVE FIGURE W 24 REPLACE DRIVER S SCUFF PLATE 1. RE-INSTALL THE DRIVER S SIDE SCUFF PLATE BY ENGAGING ALL (3) CLIPS. (FIGURE X) FIGURE X 11

12 25 REPLACE STEERING CLUMN CVERS 1. PLUG THE IGNITIN KEY LIGHT, IF EQUIPPED, BACK INT THE LWER STEERING CLUMN CVER AND CAREFULLY SNAP THE STEERING CLUMN CVER HALVES BACK TGETHER. (FIGURE Y) 2. RE-INSTALL THE (3) PHILLIPS HEAD SCREWS. VERIFY PERATIN F THE TILT STEERING WHEEL. (FIGURE Y) FIGURE Y 26 REPLACE LWER DASH PANEL 1. RE-INSTALL THE BLACK, LWER DASH PANEL BY ENGAGING THE SINGLE CLIP LCATED AT THE FRNT, CENTER F THE PANEL. RE-INSTALL BTH PLASTIC FASTENERS AND PUSH THE PLASTIC CENTER BUTTN DWN UNTIL FLUSH WITH THE FASTENER T ENGAGE. (FIGURE Z) FIGURE Z 12

13 27 FINALIZING THE INSTALLATIN 1. PLACE THE SYSTEM WNER S MANUAL AND WALLET CARDS INT THE GLVE CMPARTMENT. 2. APPLY THE WINDW WARNING DECALS T THE DRIVER AND PASSENGER SIDE WINDWS. WITH EACH WINDW FULLY CLSED, PSITIN THE DECAL N THE INSIDE GLASS SURFACE, APPRXIMATELY 1 ABVE THE WINDW DR SEAL AND 3 FRWARD F THE TRAILING EDGE F THE WINDW. BE CAREFUL HANDLING THE DECALS T AVID CNTACT WITH THE ADHESIVE SIDE F THE DECAL, AS THIS WILL LEAVE A PERMANENT FIGERPRINT BETWEEN THE DECAL AND GLASS PANEL. 3. NTE: AFTER REASSEMBLING THE VEHICLE PARTS, CHECK FR ANY DIRT. CLEAN ANY DIRTY PARTS. 4. NTE: AFTER CMPLETING THE INSTALLATIN, REFER T THE VEHICLE WNER S MANUAL FR INSTRUCTINS N HW T RESET THE CLCK AND PRESET RADI STATINS.! 5. CAUTIN: DISCNNECTING THE BATTERY MAY CAUSE THE DSC INDICATR LIGHT T BECME INPERABLE. (THE DSC FF INDICATR LIGHT FLASHES AND THE TCS/DSC INDICATR LIGHT IS ILLUMINATED.) PERFRM THE FLLWING PRCEDURE T RESTRE THE DSC T AN PERABLE CNDITIN, IF APPLICABLE: a. START THE VEHICLE WITH THE KEY. b. TURN THE STEERING WHEEL CMPLETELY T THE RIGHT AND THEN CMPLETELY T THE LEFT. c. VERIFY THAT THE DSC FF INDICATR LIGHT TURNS FF. d. TURN THE IGNITIN SWITCH T THE FF PSITIN AND THEN TURN IT T THE N PSITIN AGAIN. e. VERIFY THAT THE TCS/DSC INDICATR LIGHT TURNS FF.! 6. CAUTIN: WHEN THE BATTERY IS DISCNNECTED, THE WINDWS MAY NT FULLY PEN AND CLSE AUTMATICALLY. PERFRM THE FLLWING PRCEDURE T THE DRIVER AND PASSENGER FRNT WINDWS T RESUME PERATIN, IF APPLICABLE: a. TURN THE IGNITIN SWITCH T THE N PSITIN. b. PRESS DWN THE WINDW SWITCH N THE FRNT PASSENGER S SIDE DR PANEL AND FULLY PEN THE WINDW. c. PULL UP THE WINDW SWITCH N THE FRNT PASSENGER S SIDE DR PANEL AND CNTINUE HLDING FR APPRXIMATELY 3 SECNDS T FULLY CLSE THE WINDW. d. PRESS DWN BTH FRNT WINDW SWITCHES N THE DRIVER S DR PANEL AND FULLY PEN THE WINDWS. e. PULL UP BTH FRNT WINDW SWITCHES N THE DRIVER S DR PANEL AND CNTINUE HLDING FR APPRXIMATELY 3 SECNDS T FULLY CLSE THE WINDWS. f. TURN THE IGNITIN SWITCH T THE FF PSITIN. 13

14 SYMPTM TRUBLE-SHTING GUIDE PRBABLE CAUSE SLUTIN SYSTEM WILL NT PERATE. FUSE MISSING R BLWN. INSERT R REPLACE 10A FUSE LCATED N THE SECURITY SYSTEM HARNESS. KEYLESS ENTRY SYSTEM IS NT FUNCTIN- ING. MDULE NT RECEIVING PWER. MDULE NT RECEIVING GRUND. MDULE NT RESPNDING. CHECK TRANSMITTER BATTERIES. CHECK PIN #13 N MDULE 24-PIN CN- NECTR FR CNSTANT +12VDC. CHECK PIN #14 N MDULE 24-PIN CN- NECTR FR GRUND. REPLACE MDULE. SYSTEM WILL NT ARM DR PEN. IGNITIN KEY N. MDULE NT RECEIVING ARM INPUT. SHUT DR. TURN IGNITIN KEY FF. CHECK PIN #9 N MDULE 24-PIN CNNEC- TR FR +12VDC WHEN LCK IS PRESSED N THE KEYLESS ENTRY TRANSMITTER. CHECK 16-PIN CNNECTR AT BDY CNTRL MDULE IF VLTAGE IS NT PRESENT. SYSTEM WILL NT DISARM MDULE NT RECEIVING DISARM INPUT. CHECK PIN #6 N MDULE 24-PIN CNNEC- TR FR +12VDC WHEN UNLCK IS PRESSED N THE KEYLESS ENTRY TRANSMIT- TER T UNLCK THE DRIVER S DR. CHECK 16-PIN CNNECTR AT BDY CNTRL MDULE IF VLTAGE IS NT PRESENT. 14

15 SECURITY SYSTEM DIAGRAM 15

16 16

17 FINAL INSPECTIN Inspect the installed / reinstalled parts for the following items: Inspection Items ( ) Inspection Parts Clearance / Fit Scratches / Dirt / Harness Interference Installation / Tightening / Engagement peration Check Negative battery terminal Driver-side scuff plate Driver-side door seal Driver-side kick panel Driver-side lower dash panel Steering column covers Programming button installed Security System features: - system arm - starter interrupt - door trigger - system disarm - shock sensor wner s manual and wallet cards *6 *1 *2 *3 *4 *5 : Applicable *1: Press the lock button on the transmitter, horn beeps and parking lights flash one time. *2: Attempt to start vehicle with key, starter should not crank. *3: Manually unlock and open any door. Horn will sound and parking lights will flash. *4: Press the unlock button on the transmitter, horn beeps and lights flash four times. *5: Arm security system by pressing the lock button on the transmitter. Test the light touch and full trigger features. *6: In vehicle glove box (Port installations only). Date: / / Vehicle: VIN: Person in charge Checked Approved 17