Cat. No Printed 11/94 PORTABLE SERVICE EQUIPMENT & SUPPLIES WITH PARTS LIST Culligan International Company Printed in USA

Transcription

1 Cat. No Printed 11/94 PORTABLE SERVICE EQUIPMENT & SUPPLIES WITH PARTS LIST 1994 Culligan International Company Printed in USA

2

3 PORTABLE SERVICE EQUIPMENT & SUPPLIES WITH PARTS LIST Table of Contents Tanks...1 Filtr-Cleer Media Packs...2 Tank Parts...3 Service Unit Accessories...4 Installation Supplies...5 Portable Exchange Accessories...6 Transfer Cart...7 Transfer Cart Parts...8 Cul-Flo-Valv Bypass and Accessories...9 Cul-Flo-Valv Bypass Parts...10

4

5 FINEST QUALITY WATER CONDITIONING TANKS AVAILABLE! SPECIAL QUANTITY PRICING! SLIP COUPLINGS: 3-INCH O.C. 44-1/8 INCHES HIGH PLASTIC INLET MANIFOLD CORROSION RESISTANT, PLASTIC OUTLET MANIFOLD 7 and 9-INCH DIAMETERS 14 GAUGE STEEL SIDE SHEET EVERY PART OF EVERY CULLIGAN CONDITIONER IS THOROUGHLY TESTED AND INSPECTED BURST TESTED TO 600 PSI CHOICE OF TWO TANK STYLES DUBL-HULL LINED, OR GALVANIZED CHOICE OF ION EXCHANGER OR FILTER MEDIA DESIGNED FOR EFFICIENT DOWNFLOW SOFTENING OR FILTERING 10 GAUGE STEEL SKIRT

6 DUBL-HULL TANKS ONLY Corrosion Free!! Complete with Plastic Inner Liner & Upper Seal NO FITTINGS, MEDIA OR MANIFOLDS inch inch WITH FITTINGS AND MANIFOLDS inch GALVANIZED TANKS ONLY Hot-Dipped Galvanized Inside and Out. Not Recommended for highly Corrosive Water NO FITTINGS, MEDIA OR MANIFOLDS inch inch FILTR-CLEER MEDIA-PAK Used for preparation of a Filtr-Cleer, 9-inch portable service exchange filter only. Media-Pak consists of five different filtration media plus decal for tank and instructions for preparing unit. Use either galvanized or Dubl-Hull tank depending on corrosive tendencies of water being filtered. Catalog No NOTE: The following special items are needed to prepare filled unit. Quantity Female Fitting Flow Control (8gpm) Male Tank Fitting 1 2

7 DUBL-HULL SERVICE TANK PARTS No Nut Ring Plate ( Present) Plate ( ) Gasket, Three Hole, Notched Barrier, Plastic, Three Hole Yoke, Two Hole Plastic Inner Tank, 7-inch Plastic Inner Tank, 9-inch Coupling, Inlet Inlet Manifold, Fine Slot Outlet Manifold, Plastic Plug, Zinc Plated Inlet Manifold (Hot Water) Outlet Manifold (Hot Water) Coupling, Outlet, Plastic Mold GALVANIZED SERVICE TANK PARTS CUL -DUR LINED SERVICE TANK PARTS inch Tank only, less fittings inch Tank only, less fittings Coupling, Inlet Inlet Manifold, Fine Slot, Delrin Inlet Manifold, Fine Slot, Brass Outlet Manifold, Plastic Outlet Manifold, Unsheathed Brass Plug, Zinc-Plated Coupling, Inlet Inlet Manifold, Fine Slot, Delrin Outlet Manifold, Plastic Plug, Zinc-Plated, 3/4-inch 3

8 SERVICE UNIT ACCESSORIES Code Part Number A Connector with Lock Ring, 8-3/4 inches long Connector with Lock Ring, 12-inches long Connector with Lock Ring, 24-inches long 30 DAY DELIVERY Connector with Lock Ring, 14-inches long Connector with Lock Ring, 18-inches long Connector with Lock Ring, 30-inches long Connector with Lock Ring, 36-inches long Connector with Lock Ring, 42-inches long Connector with Lock Ring, 54-inches long Connector w/o Lock Ring, 8-3/4 inches long B Hot Water Connector with Brass Lock Ring, 8-3/4 inches long Hot Water Connector w/o Brass Lock Ring, 8-3/4 inches long C Plastic Lock Ring D Cap-Red Cap-Black E Female Coupling, 1/2 inch Female Coupling, 3/4 inch (not shown) F Female Coupling, 3/4 inch G Lubricated Gasket (Diaphragm Type) Pack of 100 only H Lubricated Gasket (Standard Type) Pack of 100 only I Plastic Inlet Manifold Brass Inlet Manifold 2-3/8 inches (Hot Water) Brass Inlet Manifold 4-1/4 inches Plastic Outlet Manifold Brass Outlet Manifold-(Hot Water) J Cut Gasket, Black-Pack of 100 only Cut Gasket, Red (Thick)-Pack of 100 only K Fiber Washer-Pack of 100 only L Screen Gasket C A B D E F G H I J K L 4

9 SERVICE UNIT ACCESSORIES DRIP PAN Code A A Drip Pan, 15-1/4" Dia., 1-5/8" Deep (for 12-inch Softeners) B Drip Pan, 11-3/4" Dia., 1-3/4" Deep (for 7 and 9-inch Service Units) B MANIFOLD TIP - NYLON For conversion of outlet manifolds. Slotted section is molded nylon tip. Open end is extruded for sweat soldering to upper part of outlet manifold tube Manifold Tip-Nylon 8-11/16" overall INSTALLATION SUPPLIES A Code A U-Bend, ¾" with Male N.P.T. Adapter B Culligan Valve, ¾"; 1-¾" turns- Open to Close, 2½" Lg. x 3¼" high B 5

10 PORTABLE EXCHANGE ACCESSORIES TANK SLING Adjustable, double shoulder type, heavy duck canvas sling. "Sure-lock" buckles allow adjustment of sling to any desired size. The shoulder supports divide weight equally on both shoulders. Loop twist automatically swings unit to exchange man's side for tight quarters through doors and down narrow stairways. Double-folded webbing with reinforced stitching insures long service life. Catalog No EXCHANGE APRON Lightweight, tough, plastic apron reinforced with fiber. Adjustable leg and neck straps. Leather reinforced at crotch. Pockets and mallet loop as described for This apron minimizes wear and tear on uniforms. Catalog No DELUXE EXCHANGE APRON Finest quality canvas construction, reinforced with large patches at points of wear. has tough, riveted leather tool pocket on right side, loop for mallet on left side, and wide top pocket for route book, etc. Adjustable straps. Your best apron buy. Catalog No

11 HEAVY DUTY STEEL TRANSFER CART Cat. No STURDY, ONE-PIECE CONSTRUCTION ALL WELDED FRAME WITH REINFORCED GUSSET PLATES RUGGED 1-INCH TUBULAR STEEL ATTRACTIVE PAINTED FINISH TOOL HOLDER INCLUDED FOR MALLET OR KNOCK-OFF BAR TANK CHAIN PROVIDES SAFE AND EASY MOVEMENT OF SERVICE UNITS EQUIPPED TO HANDLE 7" OR 9" SERVICE UNITS SMOOTH IMPLEMENT TIRES TOTAL WEIGHT IS ONLY 35-1/2 LBS. LOAD WEIGHT DISTRIBUTED EVENLY THROUGHOUT LENGTH OF 3/4" AXLE BUILT-IN STUD PREVENTS TANK FROM SLIPPING OFF CART SHIPPED COMPLETELY ASSEMBLED 7

12 TRANSFER CART REPLACEMENT PARTS STEEL CART (Cat. No ) Wheel, complete for ¾" axle Hub (with bearings, grease fittings, lock nuts) Rim (order two for complete wheel) Tire, 300 x 7.2 ply, smooth Tube, 300 x 7 (for above) Axle, ¾" x 19" Hub Bolt (3/8") Hub Nut Hub Bolt Washer Rim Bolt Rim Nut Rim Washer Ball Bearing, 2/Wheel (for 3/4" Axle) Frame REPLACEMENT PARTS FOR DISCONTINUED TRANSFER CARTS DISCONTINUED STEEL CART (¾" Axle) (Cat. No ) Frame Wheel, complete for ¾" axle Ball Bearing, 2/Wheel (for ¾" axle) DISCONTINUED STEEL CART (5/8" Axle) Tube (3.40/3.00-7) 8

13 CULLIGAN CUL-FLO-VALV BYPASS AND ACCESSORIES CUL-FLO-VALV BYPASS Cul-Flo-Valv Bypass, ¾" x ¾" All openings Female N.P.T Cul-Flo-Valv Bypass, ¾" x ¾" All openings Female Sweat Cul-Flo-Valv Bypass, ¾" x ¾" House Lines Sweat Tankside N.P.T Cul-Flo-Valv Bypass, 1-inch Tank ¾-inch. All openings Female N.P.T. CUL-FLO-VALV BYPASS UPGRADING KIT (PRIOR TO 1967) Upgrading Kit - Complete with Delrin Stem, Four O-rings, Two Stem Knobs, and Instructions LUBRICANT & LUBRICATING SWABS Silicone Lubricant 5 Ounce Tube Lubricating Swabs (carton of 12) 9

14 CUL-FLO-VALV BYPASS PARTS VALVE BODIES ONLY Size All Openings Female NPT ¾" x ¾" House Side Sweat. ¾" x ¾" Tank Side NPT All Openings Female NPT House 1-in. Tank ¾-in All Openings Female Sweat. ¾" x ¾" STEMS, KNOB & O-RING 1967 TO DATE Delrin Valve Stem-Less O-ring O-ring * Knob-"Push for Soft Water" (Blue) **Knob-"Push to Bypass" (Red) PRIOR TO 1967 Brass Valve Stem with 4 O-rings, Used with Cul-Flo-Valvs (not available) Brass Valve Stem with 4 O-rings and Check Valve. (See Bulletin G-6333 Oct. 2, 1963) Stem Knob-Blue (Cul-Flo-Valv) Stem Knob-Red (Cul-Flo-Valv) O-rings - All stems Screw for all Knobs *Knob manufactured in blue plastic since 1972 **Knob manufactured in red plastic since 1972 For replacement, order Cat. No Upgrading Kit. 10