DTC P0139, P0159 HO2S2 MONITOR ITEM CONDITION SPECIFICATION. DTC No. Trouble diagnosis name DTC detecting condition Possible cause P (Bank 1)
|
|
- Milo Dennis
- 6 years ago
- Views:
Transcription
1 T P0139, P0159 O2S2 omponent escription The heated oxygen sensor 2, after three way catalyst 1, monitors the oxygen level in the exhaust gas on each bank. ven if switching characteristics of the heated oxygen sensor 1 are shifted, the air-fuel ratio is controlled to stoichiometric, by the signal from the heated oxygen sensor 2. This sensor is made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. Under normal conditions the heated oxygen sensor 2 is not used for engine control operation. PP:2260 BS000VV ONSUT- Reference Value in ata onitor ode Specification data are reference values. ONTOR T ONTON SPTON S327R BS000VW O2S2 (B1) O2S2 (B2) O2S2 NTR (B1) O2S2 NTR (B2) Warm-up condition fter keeping engine speed between 3,500 and 4,000 rpm for one minute and at idle for one minute under no load. On Board iagnosis ogic Revving engine from idle to 3,000 rpm quickly. The heated oxygen sensor 2 has a much longer switching time between rich and lean than the heated oxygen sensor 1. The oxygen storage capacity before the three way catalyst causes the longer switching time. To judge the malfunctions of heated oxygen sensor 2, monitors whether the switching response of the sensor's voltage is faster than specified during the various driving condition such as fuel-cut V pprox V N R BS000VX S302U T No. Trouble diagnosis name T detecting condition Possible cause P (Bank 1) P (Bank 2) eated oxygen sensor 2 circuit slow response t takes more time for the sensor to respond between rich and lean than the specified time. arness or connectors (The sensor circuit is open or shorted) eated oxygen sensor 2 uel pressure njectors ntake air leaks -249
2 T onfirmation Procedure T P0139, P0159 O2S2 NOT: f T onfirmation Procedure has been previously conducted, always turn ignition switch O and wait at least 10 seconds before conducting the next test. WT ONSUT- TSTN ONTON: or better results, perform T WOR SUPPORT at a temperature of 0 to 30 (32 to 86 ). 1. Turn ignition switch ON and select T ONTOR mode with ONSUT-. 2. Start engine and warm it up to the normal operating temperature. 3. Turn ignition switch O and wait at least 10 seconds. 4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least one minute under no load. 5. et engine idle for one minutes. 6. ake sure that OON TP/S indicates more than 70 (158 ). S174Y f not, warm up engine and go to next step when OON TP/S indication reaches to 70 (158 ). 7. Select O2S2 (B1) P0139 or O2S2 (B2) P0159 of O2S2 in T WOR SUPPORT mode with ONSUT-. 8. Start engine and following the instruction of ONSUT-. BS000VY 9. ake sure that O is displayed after touching S- RSUTS. f N is displayed, refer to -255, "iagnostic Procedure". f N NOT B NOS is displayed, perform the following. a. Turn ignition switch O and leave the vehicle in a cool place (soak the vehicle). b. Return to step 1. Overall unction heck PBB0115 Use this procedure to check the overall function of the heated oxygen sensor 2 circuit. uring this check, a T might not be confirmed. WT ST 1. Start engine and warm it up to the normal operating temperature. 2. Turn ignition switch O and wait at least 10 seconds. 3. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least one minute under no load. 4. et engine idle for one minutes. 5. Set voltmeter probes between terminal 74 [O2S2 (B1) signal] or 55 [O2S2 (B2) signal] and engine ground. BS000VZ -250
3 6. heck the voltage when revving up to 4,000 rpm under no load at least 10 times. (epress and release accelerator pedal as soon as possible.) change of voltage should be more than 0.06V for 1 second during this procedure. f the voltage can be confirmed in step 6, step 7 is not necessary. 7. eep vehicle at idling for 10 minutes, then check the voltage. Or check the voltage when coasting from 80 km/h (50 P) in position (/T), 4th gear position (/T). change of voltage should be more than 0.06V for 1 second during this procedure. 8. f N, go to -255, "iagnostic Procedure". PBB
4 Wiring iagram BN 1 BS002ZQ TBWT
5 Specification data are reference values and are measured between each terminal and ground. UTON: o not use ground terminals when measuring input/output voltage. oing so may result in damage to the 's transistor. Use a ground other than terminals, such as the ground. TR- N NO. 74 W 78 B WR OOR T ONTON T ( Voltage) eated oxygen sensor 2 (bank 1) Sensors' ground (eated oxygen sensor) [ngine is running] Warm-up condition Revving engine from idle to 3,000 rpm quickly after the following conditions are met. fter keeping the engine speed between 3,500 and 4,000 rpm for one minute and at idle for one minute under no load. [ngine is running] Warm-up condition dle speed 0 - pproximately 1.0V pproximately 0V -253
6 BN 2 TBWT
7 Specification data are reference values and are measured between each terminal and ground. UTON: o not use ground terminals when measuring input/output voltage. oing so may result in damage to the 's transistor. Use a ground other than terminals, such as the ground. TR- N NO. WR OOR 55 B/OR 78 B iagnostic Procedure 1. RTTN ROUN SRWS 1. Turn ignition switch O. 2. oosen and retighten engine ground screws. T ONTON T ( Voltage) eated oxygen sensor 2 (bank 2) Sensors' ground (eated oxygen sensor) [ngine is running] Warm-up condition Revving engine from idle to 3,000 rpm quickly after the following conditions are met. fter keeping the engine speed between 3,500 and 4,000 rpm for one minute and at idle for one minute under no load. [ngine is running] Warm-up condition dle speed 0 - pproximately 1.0V pproximately 0V BS000W1 >> O TO 2. PBB
8 2. R T S-RNN T With ONSUT- 1. Start engine and warm it up to normal operating temperature. 2. Select S-RNN ONT in WOR SUPPORT mode with ONSUT-. 3. lear the self-learning control coefficient by touching R. 4. Run engine for at least 10 minutes at idle speed. s the 1st trip T P0171, P0172, P0174 or P0175 detected? s it difficult to start engine? S968Y Without ONSUT- 1. Start engine and warm it up to normal operating temperature. 2. Turn ignition switch O. 3. isconnect mass air flow sensor harness connector, and restart and run engine for at least 5 seconds at idle speed. 4. Stop engine and reconnect mass air flow sensor harness connector. 5. ake sure T P0102 is displayed. 6. rase the T memory. Refer to -69, "OW TO RS SSON-RT NOST NORTON". 7. ake sure T P0000 is displayed. 8. Run engine for at least 10 minutes at idle speed. s the 1st trip T P0171, P0172, P0174 or P0175 detected? s it difficult to start engine? PBB1077 Yes or No Yes >> Perform trouble diagnosis for T P0171, P0174 or P0172, P0175. Refer to -260 or No >> O TO O2S2 ROUN RUT OR OPN N SORT 1. Turn ignition switch O. 2. isconnect heated oxygen sensor 2 harness connector. 3. heck harness continuity between O2S2 terminal 4 and engine ground. Refer to Wiring iagram. ontinuity should exist. 4. lso check harness for short to ground and short to power. O or N O >> O TO 5. N >> O TO 4. PBB TT UNTONN PRT heck the following. oint connector-3 arness for open or short between O2S2 and engine ground >> Repair open circuit or short to ground or short to power in harness or connectors. -256
9 5. O2S2 NPUT SN RUT OR OPN N SORT 1. isconnect harness connector. 2. heck harness continuity between terminal and O2S2 terminal as follows. Refer to Wiring iagram. Terminals T Sensor Bank P P ontinuity should exist. 3. heck harness continuity between the following terminals and ground. Refer to Wiring iagram. Terminals T Sensor Bank P P ontinuity should not exist. 4. lso check harness for short to ground and short to power. O or N O >> O TO 7. N >> O TO TT UNTONN PRT heck the following. oint connector-3 arness for open or short between O2S2 and >> Repair open circuit or short to ground or short to power in harness or connectors. 7. T OXYN SNSOR 2 Refer to -258, "omponent nspection". O or N O >> O TO 8. N >> Replace malfunctioning heated oxygen sensor NTRTTNT NNT Refer to -137, "TROUB NOSS OR NTRTTNT NNT". >> NSPTON N -257
10 omponent nspection T OXYN SNSOR 2 With ONSUT- 1. Turn ignition switch ON and select T ONTOR mode with ONSUT-. 2. Start engine and warm it up to the normal operating temperature. 3. Turn ignition switch O and wait at least 10 seconds. 4. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least one minute under no load. 5. et engine idle for one minutes. BS0031 S174Y 6. Select U NTON in TV TST mode, and select O2S2 (B1)/(B2) as the monitor item with ONSUT-. S662Y 7. heck O2S2 (B1)/(B2) at idle speed when adjusting U NTON to ±25%. PBB0796 O2S2 (B1)/(B2) should be above 0.63V at least once when the U NTON is +25%. O2S2 (B1)/(B2) should be below 0.48V at least once when the U NTON is 25%. UTON: iscard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one. Before installing new oxygen sensor, clean exhaust system threads using Oxygen Sensor Thread leaner tool or and approved anti-seize lubricant. Without ONSUT- 1. Start engine and warm it up to the normal operating temperature. 2. Turn ignition switch O and wait at least 10 seconds. 3. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least one minute under no load. 4. et engine idle for one minutes. 5. Set voltmeter probes between terminal 74 [O2S2 (B1) signal] or 55 [O2S2 (B2) signal] and engine ground. -258
11 6. heck the voltage when revving up to 4,000 rpm under no load at least 10 times. (epress and release accelerator pedal as soon as possible.) The voltage should be above 0.63V at least once during this procedure. f the voltage is above 0.63V at step 6, step 7 is not necessary. 7. eep vehicle at idling for 10 minutes, then check voltage. Or check the voltage when coasting from 80 km/h (50 P) in position (/T), 4th gear position (/T). The voltage should be below 0.48V at least once during this PBB1108 procedure. 8. f N, replace heated oxygen sensor 2. UTON: iscard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one. Before installing new oxygen sensor, clean exhaust system threads using Oxygen Sensor Thread leaner tool or and approved anti-seize lubricant. Removal and nstallation T OXYN SNSOR 2 Refer to -23, "XUST NO N TR WY TYST". BS000W3-259
DTC P1273, P1283 A/F SENSOR 1 MONITOR ITEM CONDITION SPECIFICATION
T P1273, P1283 / SNSOR 1 omponent escription The air fuel ratio (/) sensor 1 is a planar dual-cell limit current sensor. The sensor element of the / sensor 1 is the combination of a Nernst concentration
More informationDTC P1229 SENSOR POWER SUPPLY. DTC No. Trouble diagnosis name DTC detecting condition Possible cause
T P1229 SNSOR POWR SUPPY On Board iagnosis ogic This self-diagnosis has the one trip detection logic. T No. Trouble diagnosis name T detecting condition Possible cause PP:16119 UBS00W P1229 1229 circuit
More informationTROUBLE DIAGNOSIS. ECM Harness Connector Terminal Layout. ECM Terminals and Reference Value EC-661 [VG33E]
arness onnector Terminal ayout UBS007V Terminals and Reference Value PRPRTON 1. is located behind the instrument lower cover. or this inspection: Remove instrument lower cover. S533P UBS007V 106 2. Remove
More informationDTC P1273 A/F SENSOR 1 MONITOR ITEM CONDITION SPECIFICATION
Component Description DTC P1273 A/F SENSOR 1 The A/F sensor 1 is a planar dual-cell limit current sensor. The sensor element of the A/F sensor 1 is the combination of a Nernst concentration cell (sensor
More informationENGINE CONTROL SYSTEM
ST TR SYST TTS 24 SRV RT... 4 X R T... 4 T o. ndex...4 lphabetical ndex...4 RUTS... 6 recaution for Supplemental Restraint System (SRS) "R B" and "ST BT R-T- SR"...6 n Board iagnosis (B) System of ngine...6
More informationBRAKE CONTROL SYSTEM SECTION BRC CONTENTS BRAKES BRC-1 VDC/TCS/ABS BASIC INSPECTION... 4 COMPONENT DIAGNOSIS...27 FUNCTION DIAGNOSIS...
RS ST R R TR SYST TTS V/TS/S S ST... 4 SS RR WRFW... 4 Work Flow...4 iagnostic Work Sheet...7 ST USTT... 8 T SRV W R TR UT...8 T SRV W R TR UT : escription...8 T SRV W R TR UT : Special Repair Requirement...8
More informationBRAKE CONTROL SYSTEM SECTION BRC CONTENTS BRAKES BRC-1 ABS BASIC INSPECTION... 6 FUNCTION DIAGNOSIS... 9 COMPONENT DIAGNOSIS...16
RS ST R TR SYST TTS S S ST... 6 SS RR WRFW... 6 Work Flow...6 iagnostic Work Sheet...8 FUT SS... 9 S... 9 System iagram...9 System escription...9 omponent arts ocation...11 omponent escription...12 SUT-
More informationSTEERING CONTROL SYSTEM
STRG ST ST STRG TR SYST TTS WTUT RR TV STR S ST... 4 GSS RR WR W... 4 Work low...4 SYST SRT... 5 S SYST... 5 System iagram...5 System escription...5 omponent arts ocation...7 omponent escription...7 T/RUT
More informationPOWER CONTROL SYSTEM SECTION PCS CONTENTS ELECTRICAL & POWER CONTROL PCS-1 IPDM E/R FUNCTION DIAGNOSIS... 3 ECU DIAGNOSIS...19 PRECAUTION...
TR & WR TR ST S WR TR SYSTM TTS M /R iagnosis rocedure...17 UT SS... 3 RY TR SYSTM... 3 System iagram...3 System escription...4 omponent arts ocation...4 WR TR SYSTM... 6 System iagram...6 System escription...6
More informationSRS AIRBAG CONTROL SYSTEM
RSTRTS ST SRS R TR SYST TTS S ST... 3 SS RR WR W... 3 Work low...3 TRTTT T... 5 nspection rocedure...5 Trouble iagnosis with SUT...5 SYST SRT... 6 SRS R SYST... 6 SRS onfiguration...6 SRS omponent arts
More informationCHARGING SYSTEM SECTION CHG CONTENTS ELECTRICAL & POWER CONTROL CHG-1 BASIC INSPECTION... 2 SYMPTOM DIAGNOSIS...17 FUNCTION DIAGNOSIS...
TR & WR TR ST R SYSTM TTS S ST... 2 SS RR WRW... 2 Work low...2 UT SS... 3 R SYSTM... 3 System iagram...3 System escription...3 omponent escription...3 WR RT VT VR- TR SYSTM... 4 System iagram...4 System
More informationCHARGING SYSTEM SECTION CHG CONTENTS ELECTRICAL & POWER CONTROL CHG-1 PRECAUTION... 2 PREPARATION... 3 BASIC INSPECTION... 4 FUNCTION DIAGNOSIS...
TR & WR TR ST R SYSTM TTS RUT... 2 RUTS... 2 Supplemental Restraint System (SRS) "R " and "ST T R-TSR"...2 recaution for ower eneration Variable Voltage ontrol System...2 RRT... 3 RRT... 3 Special Service
More informationTROUBLE DIAGNOSIS. ECM Harness Connector Terminal Layout. ECM Terminals and Reference Value EC-677 [QG18DE (CALIF CA)]
arness onnector Terminal ayout UBS001R Terminals and Reference Value PRPRTON 1. is located in the right side of the cowl top (behind the strut tower). or this inspection: Remove engine control harness
More informationDRIVE MODE SYSTEM SECTION DMS CONTENTS CRUISE CONTROL & DRIVER ASSISTANCE DMS-1. Infiniti Drive Mode Selector BASIC INSPECTION...
RUS OTRO & RVR SSST STO S RV O SYST OTTS nfiniti rive ode Selector nfiniti rive ode Selector... 8 SYST SRTO... 2 SRTO... 2 nfiniti rive ode Selector...2 OOT RTS... 3 omponent arts ocation...3 omponent
More informationSTEERING CONTROL SYSTEM
STRG ST STRG TR SYST TTS RUT... 3 RUTS... 3 recaution for Supplemental Restraint System (SRS) "R G" and "ST T R-T- SR"...3 Service otice and recautions for S System...3 RRT... 4 RRT... 4 ommercial Service
More informationSECURITY CONTROL SYSTEM
Y XTRR, RS, R & V URTY T URTY TR SYST TTS WT TT KY SYST S T... 5 SS RR WRKW... 5 Work low...5 T USTT... 8 T SRV W R TR UT...8 T SRV W R TR UT : Special Repair Requirement...8 R-UT UT...8 R-UT UT : escription...8
More informationBRAKE CONTROL SYSTEM SECTION BRC CONTENTS BRAKES BRC-1 ABS SERVICE INFORMATION... 2
RS ST R R TR SYST TTS S ydraulic ircuit iagram... 6 R SRV FRT... 2 T X... 2 1101-1115...2 1120-1191...2 U1000...2 RUTS... 3 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"...3
More informationSECURITY CONTROL SYSTEM
Y XTRR, RS, R & V URTY T URTY TR SYST TTS WT TT KY SYST S T... 5 SS RR WRKW... 5 Work low...5 T USTT... 8 T SRV W R TR UT...8 T SRV W R TR UT : Special Repair Requirement...8 R-UT UT...8 R-UT UT : escription...8
More informationPOWER CONTROL SYSTEM SECTION PCS CONTENTS ELECTRICAL & POWER CONTROL PCS-1 IPDM E/R SYSTEM DESCRIPTION... 4 ECU DIAGNOSIS INFORMATION...
TR & WR TR ST S WR TR SYSTM TTS M /R iagnosis rocedure...17 SYSTM SRT... 4 RY TR SYSTM... 4 System iagram...4 System escription...5 omponent arts ocation...6 WR TR SYSTM... 7 System iagram...7 System escription...7
More informationSECURITY CONTROL SYSTEM
Y XTRR, RS, R & V URTY T URTY TR SYST TTS WT TT KY SYST S T... 3 SS RR WRKW... 3 Work low...3 R-T R ST... 6 asic nspection...6 Vehicle Security peration heck...6 T USTT... 8 T SRV W R TR UT...8 T SRV W
More informationFUEL SYSTEM SECTION FL CONTENTS ENGINE FL-1 PRECAUTION... 2 ON-VEHICLE REPAIR... 7 PREPARATION... 4 SERVICE DATA AND SPECIFICATIONS (SDS)...
ST U SYST TTS RUT... 2 RUTS... 2 recaution for Supplemental Restraint System (SRS) "R B" and "ST BT R-T- SR"...2 recautions ecessary for Steering Wheel Rotation after Battery isconnect (arly roduction,
More informationPOWER CONTROL SYSTEM SECTION PCS CONTENTS ELECTRICAL & POWER CONTROL PCS-1 IPDM E/R SYSTEM DESCRIPTION... 2 ECU DIAGNOSIS INFORMATION...
TR & WR TR ST S WR TR SYSTM TTS M /R SYSTM SRT... 2 RY TR SYSTM... 2 System iagram...2 System escription...3 omponent arts ocation...4 WR TR SYSTM... 5 System iagram...5 System escription...5 S UR SYSTM...
More informationWARNING CHIME SYSTEM SECTION WCS CONTENTS DRIVER INFORMATION & MULTIMEDIA WCS-1 BASIC INSPECTION... 3 SYSTEM DESCRIPTION... 4
RVR NRT & UT ST WRNN SYST TNTS S NST... 3 NSS N RR WRW... 3 Work low...3 SYST SRT... 4 WRNN SYST... 4 WRNN SYST...4 WRNN SYST : System iagram...4 WRNN SYST : System...4 WRNN SYST : omponent arts ocation...5
More informationWIPER & WASHER SECTION WW CONTENTS DRIVER CONTROLS WW-1 BASIC INSPECTION... 3 SYSTEM DESCRIPTION... 6 ECU DIAGNOSIS INFORMATION...
RVR TRLS ST WR & WSR TTS S ST... 3 SS RR WRLW... 3 Work low...3 SYST SRT... 6 RT WR WSR SYST... 6 System iagram...6 System escription...6 omponent arts Location...9 omponent escription...10 SS SYST ()...11
More informationDEFOGGER SECTION DEF CONTENTS DRIVER CONTROLS DEF-1 BASIC INSPECTION... 3 SYSTEM DESCRIPTION... 6 ECU DIAGNOSIS INFORMATION...21
RVR TRLS ST R TTS S ST... 3 SS RR WRLW... 3 Work low...3 SYST SRT... 6 RR WW R SYST... 6 System iagram...6 System escription...6 omponent arts Location...7 omponent escription...7 SS SYST ()... 9 T...9
More informationCHARGING SYSTEM SECTION CHG CONTENTS ELECTRICAL & POWER CONTROL CHG-1 BASIC INSPECTION... 2 WIRING DIAGRAM...11 SYSTEM DESCRIPTION...
TR & WR TR ST R SYSTM TTS S ST... 2 SS RR WRW... 2 Work low...2 SYSTM SRT... 3 R SYSTM... 3 System iagram...3 System escription...3 omponent escription...3 WR RT VT VR- TR SYSTM... 4 System iagram...4
More informationSTEERING CONTROL SYSTEM
STRG ST STRG TR SYST TTS RUT... 3 RUTS... 3 recaution for Supplemental Restraint System (SRS) "R G" and "ST T R-T- SR"...3 Service otice or recautions for S System...3 SYST SRT... 5 T RTS... 5 omponent
More informationPOWER WINDOW CONTROL SYSTEM
Y XTRR, RS, R & V SURTY ST W WR WW TR SYST TTS RT Y UT W RUT... 6 RUTS... 6 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"...6 recaution for Work...6 RRT... 7 RRT... 7 Special
More informationACCELERATOR CONTROL SYSTEM
ST TTS RUT... 2 RUTS... 2 recaution for Supplemental Restraint System (SRS) "R B" and "ST BT R-T- SR"...2 RV STT... 3... 3 SST SYST...3 SST SYST : xploded View...3 SST SYST : Removal and nstallation...
More informationPOWER CONTROL SYSTEM SECTION PCS CONTENTS ELECTRICAL & POWER CONTROL PCS-1 IPDM E/R PRECAUTION... 3 ECU DIAGNOSIS INFORMATION...16 WIRING DIAGRAM...
TR & WR TR ST WR TR SYSTM TTS M /R RUT... 3 RUTS... 3 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"...3 recaution ecessary for Steering Wheel Rotation after attery isconnect...3
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 5 INSPECTION AND ADJUSTMENT...
TR & POWR TRO ST S OY TRO SYSTM TNTS S NSPT... 3 NSPT N USTMNT... 3 T SRV WN RPN TRO UNT...3 T SRV WN RPN TRO UNT : escription...3 T SRV WN RPN TRO UNT : Special Repair Requirement...3 URT...3 URT : escription...3
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 5 INSPECTION AND ADJUSTMENT...
TR & WR TR ST S Y TR SYSTM TTS S ST... 3 ST USTMT... 3 T SRV W R TR UT...3 T SRV W R TR UT : escription...3 T SRV W R TR UT : Special Repair Requirement...3 URT...3 URT : escription...3 URT : Special Repair
More informationModel Year: 2007 Model: Tacoma Doc ID: RM H800NX
Page 1 of 12 Last Modified: 5-7-2008 5.1 C From: 200608 Model Year: 2007 Model: Tacoma Doc ID: RM0000013H800NX Title: 2TR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P2A00: A/F Sensor Circuit Slow Response (Bank
More informationACCELERATOR CONTROL SYSTEM
ST RTR TR SYST TTS RUT... 2 RUTS... 2 recaution for Supplemental Restraint System (SRS) "R B" and "ST BT R-T- SR"...2 RV STT... 3 RTR TR SYST... 3 xploded View... 3 Removal and nstallation... 3 SRV T STS
More informationDTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1)
05 120 05CRQ 02 DTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1) CIRCUIT DESCRIPTION Refer to DTC P0130 on page 05 101. DTC No. DTC Detecting Condition Trouble Area P0134 After engine
More informationACCELERATOR CONTROL SYSTEM
ST RTR TR SYST TTS RUT... 2 RUTS... 2 recaution for Supplemental Restraint System (SRS) "R B" and "ST BT R-T- SR"...2 RV STT... 3 RTR TR SYST... 3 xploded View... 3 Removal and nstallation... 3 SRV T STS
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 5 INSPECTION AND ADJUSTMENT...
TR & WR TR ST S Y TR SYSTM TTS S ST... 3 ST USTMT... 3 T SRV W R TR UT...3 T SRV W R TR UT :...3 T SRV W R TR UT : Special Repair Requirement...3 URT...3 URT :...3 URT : Special Repair Requirement...4
More informationLAN SYSTEM SECTION LAN CONTENTS ELECTRICAL & POWER CONTROL LAN-1 CAN FUNDAMENTAL PRECAUTION...21 PRECAUTION... 5 FUNCTION DIAGNOSIS...
TR & WR TR ST SYSTM TTS UMT RUT...21 RUT... 5 RUTS... 5 recautions for Trouble iagnosis...5 recautions for arness Repair...5 UT SS... 6 MMUT SYSTM... 6 System escription...6 System iagram...6 ommunication
More informationFUEL SYSTEM SECTION FL CONTENTS ENGINE FL-1 SERVICE INFORMATION... 2
ST U SYST TTS SRV RT... 2 RUTS... 2 recaution for Supplemental Restraint System (SRS) "R B" and "ST BT R-T- SR"...2 RRT... 3 Special Service Tool...3 ommercial Service Tool...3 U SYST... 4 hecking uel
More informationDTC P0657 Actuator Supply Voltage Circuit / Open
1GR-FE EINE CONTROL SYSTEM SFI SYSTEM 277 DTC P0657 Actuator Supply Voltage Circuit / Open MONITOR DCRIPTION The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BCM BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 6
TR & WR TR ST S Y TR SYSTM TTS M UZZR : SUT- unction...18 S ST... 3 SS RR WRW... 3 Work low...3 UT SS... 6 Y TR SYSTM... 6 System...6 omponent arts ocation...7 MT SWT R SYSTM... 8 System iagram...8 System...8
More information1 of 13 10/17/2016 1:36 PM
1 of 13 10/17/2016 1:36 PM DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) DTC P2197 Oxygen (A/F) Sensor Signal Stuck
More informationSECURITY CONTROL SYSTEM
Y XTRR, RS, R & V SURTY ST S SURTY TR SYST TTS S ST... 3 SS RR WRKW... 3 Work low...3 ST USTT... 6 T SRV W R TR UT...6 T SRV W R TR UT : Special Repair Requirement...6 R-UT UT...6 R-UT UT : escription...6
More information1GR-FE ENGINE CONTROL SYSTEM SFI SYSTEM
134 1GR-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P0136 Oxygen Sensor Circuit Malfunction (ank 1 Sensor ) DTC P0137 Oxygen Sensor Circuit Low Voltage (ank 1 Sensor ) DTC P0138 Oxygen Sensor Circuit High Voltage
More informationCYLINDER HEAD CYLINDER HEAD. On-Vehicle Service EM-131 [QR25DE]
On-Vehicle Service PP:11041 N OPRSSON PRSSUR 1. Warm up the engine to full operating temperature. 2. Release the fuel pressure. Refer to -1256, "U PRSSUR RS". 3. Remove the ignition coil and spark plug
More informationSONAR SYSTEM SECTION SN CONTENTS DRIVER INFORMATION & MULTIMEDIA SN-1 BASIC INSPECTION... 2 SYMPTOM DIAGNOSIS...21 FUNCTION DIAGNOSIS...
RVR NRTN & UT STN SNR SYST NTNTS S NSTN... 2 NSS N RR WRW... 2 Work low...2 NSTN N USTNT... 4 reliminary heck...4 UNTN NSS... 5 RR SNR SYST... 5 System iagram...5 System escription...5 omponent arts ocation...6
More informationMETER, WARNING LAMP & INDICATOR
RVR NRTN & UT STN W TR, WRNN & NTR NTNTS S NSTN... 3 NSS N RR WRW... 3 Work low...3 UNTN NSS... 4 TR SYST... 4 TR SYST...4 TR SYST : System iagram...4 TR SYST : System escription...4 TR SYST : rrangement
More informationDTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1)
05114 DIAGNOSTICS 05CRQ04 DTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1) CIRCUIT DESCRIPTION Refer to DTC P0130 on page 0596. DTC No. DTC Detecting Condition Trouble Area After
More informationWARNING CHIME SYSTEM SECTION WCS CONTENTS DRIVER INFORMATION & MULTIMEDIA WCS-1 BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 4 COMPONENT DIAGNOSIS...
RVR NRT & UT ST WS WRNN SYST TNTS S NST... 3 NSS N RR WRW... 3 Work low...3 UNT NSS... 4 WRNN SYST... 4 WRNN SYST...4 WRNN SYST : System iagram...4 WRNN SYST : System escription...4 WRNN SYST : omponent
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BCM BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 5
TR & WR TR ST S Y TR SYSTM TTS M S ST... 3 ST USTMT... 3 T SRV W R TR UT...3 T SRV W R TR UT :...3 T SRV W R TR UT : Special Repair Requirement...3 URT...3 URT :...3 URT : Special Repair Requirement...4
More informationSECURITY CONTROL SYSTEM
Y XTRR, RS, R & V SURTY ST S SURTY TR SYST TTS S ST... 3 SS RR WRKW... 3 Work low...3 ST USTT... 6 T SRV W R TR UT...6 T SRV W R TR UT : Special Repair Requirement...6 R-UT UT...6 R-UT UT : escription...6
More informationINTERIOR LIGHTING SYSTEM
RVR TRLS ST TRR LT SYST TTS S ST... 3 SS RR WRLW... 3 Work low...3 UT SS... 6 TRR R L TRL SYST... 6 System iagram...6 System escription...6 omponent arts Location...7 omponent escription...7 LLUT TRL SYST...
More information13A-1 FUEL CONTENTS MULTIPOINT FUEL INJECTION (MPI) FUEL SUPPLY... 13B
13A-1 FUEL CONTENTS MULTIPOINT FUEL INJECTION (MPI)... 13A FUEL SUPPLY... 13B 13A-2 MULTIPOINT FUEL INJECTION (MPI) CONTENTS GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 6 SEALANT... 6 SPECIAL TOOLS...
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BCM BASIC INSPECTION... 3 SYSTEM DESCRIPTION... 8
TR & POWR TRO ST S OY TRO SYSTM TNTS M S NSPT... 3 NOSS N RPR WOROW... 3 Work low...3 T SRV WN RPN TRO UNT...5 T SRV WN RPN TRO UNT :...5 T SRV WN RPN TRO UNT : Special Repair Requirement...5 URT (M)...6
More informationTRANSFER SECTION TF CONTENTS DRIVELINE/AXLE TF-1 SERVICE INFORMATION... 2 DTC INDEX... 2 P1801-P P1820-P1855, U
DRV/X ST T TRSR T TTS SRV RT... 2 DT DX... 2 1801-1819...2 1820-1855, U1000...2 RUTS... 3 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"...3 recaution for Transfer ssembly and
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BASIC INSPECTION... 3 FUNCTION DIAGNOSIS...
TR & WR TR ST S Y TR SYSTM TTS S ST... 3 ST USTMT... 3 T SRV W R TR UT (M)...3 T SRV W R TR UT (M) :...3 T SRV W R TR UT (M) : Special Repair Requirement...3 URT (M)...3 URT (M) :...3 URT (M) : Special
More informationAUTOMATIC DRIVE POSITIONER
Y TRR ST UTT RV STR TTS RUT... 5 RUTS... 5 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"...5 SYST SRT... 6 T RTS... 6 omponent arts ocation...6 omponent escription...7 SYST...11
More informationDTC P0125 Insufficient Coolant Temp. for Closed Loop Fuel Control
DI4 DIAGSTICS EINE DI38404 DTC P05 Insufficient Coolant Temp. for Closed Loop Fuel Control CIRCUIT DESCRIPTION To obtain a high purification rate for the CO, HC and x components of the exhaust gas, a threeway
More informationDTC P P0304 NO. 4-1CYLINDER MISFIRE, MULTIPLE CYLINDER MISFIRE. On Board Diagnosis Logic
DTC P0300 - P0304 NO. 4-1CYLINDER MISFIRE, On Board Diagnosis Logic On Board Diagnosis Logic When a misfire occurs, engine speed will fluctuate (vary). If the engine speed fluctuates enough to cause the
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BCM BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 8
TR & WR TR ST S Y TR SYSTM TTS M S ST... 3 SS RR WRW... 3 Work low...3 T SRV W R TR UT...5 T SRV W R TR UT :...5 T SRV W R TR UT : Special Repair Requirement...5 URT (M)...6 URT (M) :...6 URT (M) : Special
More informationCatalyst System Efficiency Below Threshold (Bank 1)
190 1NZ-FXE EINE CONTROL SYSTEM SFI SYSTEM DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) MONITOR DCRIPTION The ECM uses 2 sensors mounted before and after the three-way catalytic converter
More informationAUTOMATIC DRIVE POSITIONER
Y TRR ST UTT RV STR TTS RUT... 5 RUTS... 5 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"...5 SYST SRT... 6 T RTS... 6 omponent arts ocation...6 omponent escription...7 SYST...10
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 PRECAUTION... 3 SYSTEM DESCRIPTION... 4
TR & POWR ONTRO STON S OY ONTRO SYSTM ONTNTS PRUTON... 3 PRUTONS... 3 Precaution for Supplemental Restraint System (SRS) "R " and "ST T PR-TN- SONR"...3 SYSTM SRPTON... 4 OMPONNT PRTS... 4 OY ONTRO SYSTM...4
More informationPOWER SUPPLY, GROUND & CIRCUIT ELEMENTS
TR & WR TR ST WR SUY, RU & RUT MTS TTS WR SUY&RU RUT S ST... 3 TTRY... 3 ow to andle attery...3 Work low...5 MT SS... 6 WR SUY RUT RUT... 6 Wiring iagram - TTRY WR SUY -...6 Wiring iagram - TTRY WR SUY
More informationDTC P0171 SYSTEM TOO LEAN (BANK 1) DTC P0174 SYSTEM TOO LEAN (BANK 2)
05498 DIAGNOSTICS DTC P0171 SYSTEM TOO LEAN (BANK 1) 05EXR06 DTC P0172 SYSTEM TOO RICH (BANK 1) DTC P0174 SYSTEM TOO LEAN (BANK 2) DTC P0175 SYSTEM TOO RICH (BANK 2) CIRCUIT DESCRIPTION The fuel trim is
More information2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM
160 2UZ-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P0171 System Too Lean (Bank 1) DTC P0172 System Too Rich (Bank 1) DTC P0174 System Too Lean (Bank 2) DTC P0175 System Too Rich (Bank 2) DCRIPTION The fuel
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 WITH INTELLIGENT KEY SYSTEM PRECAUTION... 5 SYSTEM DESCRIPTION...
TR & POWR ONTRO STON S OY ONTRO SYSTM ONTNTS WT NTNT Y SYSTM PRUTON... 5 PRUTONS... 5 Precaution for Supplemental Restraint System (SRS) "R " and "ST T PR-TN- SONR"...5 SYSTM SRPTON... 6 OMPONNT PRTS...
More informationShort to Ground High Resistance Open P0132, P0131, P0132, P0133, P0134, P0131, P0132, P0133, P0134, P0137, P0140, P0151, P0152,
Page 1 of 7 2008 Pontiac G8 DTC P0140,, P2270, or P2271 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Review Strategy Based Diagnosis for
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 7 INSPECTION AND ADJUSTMENT...
TR & WR TR ST S Y TR SYSTM TTS S ST... 3 ST USTMT... 3 T SRV W R TR UT (M)...3 T SRV W R TR UT (M) :...3 T SRV W R TR UT (M) : Special Repair Requirement...3 URT (M)...3 URT (M) :...3 URT (M) : Special
More informationSRS AIRBAG SECTION SR CONTENTS RESTRAINTS SR-1 PRECAUTION... 2 PREPARATION... 4 ON-VEHICLE REPAIR... 5
RSTRTS ST S R TTS RUT... 2 RUTS... 2 recaution for Supplemental Restraint System (S) "R " and "ST T R-T- SR"...2 Service...2 ccupant lassification System...2 recautions ecessary for Steering Wheel Rotation
More informationTRANSAXLE & TRANSMISSION
TRSSS & DRV ST TRSX & TRSSS TTS S ST... 5 DSS D RR WRW... 5 Work low...5 Diagnostic Work Sheet...6 ST D DUST... 8 DDT SRV W R TRSSS SSY...8 DDT SRV W R TRSSS SSY : Description...8 DDT SRV W R TRSSS SSY
More informationHORN SECTION HRN CONTENTS DRIVER CONTROLS HRN-1 COMPONENT DIAGNOSIS... 3 PRECAUTION... 2 ON-VEHICLE REPAIR HORN... 3 Wiring Diagram...
RVR TRLS ST R TTS RUT... 2 RUTS... 2 Supplemental Restraint System (SRS) R and ST LT R-TSR...2 recautions ecessary for Steering Wheel Rotation after attery isconnect...2 T SS... 3... 3 Wiring iagram...
More informationCRUISE CONTROL SYSTEM
RUS OTRO & RVR SSST STO S RUS OTRO SYST OTTS RUTO... 4 RUTOS... 4 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SOR"...4 recautions or arness Repair...4 System Service...5 RRTO...
More informationDTC P1140, P1145 INTAKE VALVE TIMING CONTROL POSITION SENSOR. Component Description
Component Description Component Description NBEC1057 Intake valve advance unit position sensors are located in the front cylinder heads in both bank 1 and bank 2. This sensor uses a Hall IC (element).
More informationSTEERING SYSTEM SECTION ST CONTENTS STEERING ST-1 PRECAUTION... 3 DTC/CIRCUIT DIAGNOSIS...17 PREPARATION... 5 SYSTEM DESCRIPTION...
RG RG SY TTS RUT... 3 RUTS... 3 recaution for Supplemental Restraint System (SRS) "R G" and " T R-T- SR"...3 recaution ecessary for Steering Wheel Rotation after attery isconnect...3 Service otice or recautions
More informationTRANSAXLE & TRANSMISSION
TRSSS & DRV ST TRSX & TRSSS TTS VT: R009 S ST... 5 DSS D RR WR W... 5 Work low...5 Diagnostic Work Sheet...6 ST D DUST... 8 DDT SRV W R TR UT...8 DDT SRV W R TR UT : recaution for and VT ssembly Replacement...8
More informationDTC P0120 THROTTLE POSITION SENSOR. Description
Description Description NOTE: If DTC P0120 (0403) is displayed with DTC P0510 (0203), first perform the trouble diagnosis for DTC P0510. Refer to EC-1033. COMPONENT DESCRIPTION NGEC0595S01 The throttle
More information1GR-FE ENGINE CONTROL SYSTEM SFI SYSTEM
348 DTC DTC P200 P203 /F Sensor Circuit Slow Response (ank 1 Sensor 1) /F Sensor Circuit Slow Response (ank 2 Sensor 1) DTC P200 indicates malfunctions related to the bank 1 /F sensor. DTC P203 indicates
More informationPOWER SUPPLY, GROUND & CIRCUIT ELEMENTS
TR & WR TR ST WR SUY, RU & RUT MTS TTS S ST... 2 TTRY... 2 ow to andle attery...2 Work low...4 MT SS... 5 WR SUY RUT RUT... 5 Wiring iagram attery ower Supply...5 Wiring iagram ccessory ower Supply...12
More informationEXTERIOR LIGHTING SYSTEM
RVR TRLS ST XTRR LT SYST TTS RUT... 4 RUTS... 4 recaution for Technicians Using edical lectric...4 oint to e hecked efore Starting aintenance Work...4 recaution for Supplemental Restraint System (SRS)
More informationDOOR & LOCK SECTION DLK CONTENTS BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY DLK-1 PRECAUTION... 6 PREPARATION... 7 SYSTEM DESCRIPTION...
Y XTRR, RS, R & V SURTY ST K R & K TTS RUT... 6 RUTS... 6 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"...6 recaution for Servicing oors and ocks...6 RRT... 7 RRT... 7 Special
More information2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM
420 2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM DTC DTC P200 P203 /F Sensor Circuit Slow Response (ank 1 Sensor 1) /F Sensor Circuit Slow Response (ank 2 Sensor 1) DCRIPTION DTC P200 indicates malfunctions
More informationDTC P0136 OXYGEN SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2)
05122 DIGNOSTICS DTC P0136 OXYGEN SENSOR CIRCUIT MLFUNCTION (NK 1 SENSOR 2) 05CRR03 CIRCUIT DESCRIPTION Refer to DTC P0130 on page 0596. DTC No DTC Detection Condition Trouble rea P0136 The following condition
More informationDTC P0420 CATALYST SYSTEM EFFICIENCY BELOW THRESHOLD (BANK 1)
DTC P0420 CATALYST SYSTEM EFFICIENCY BELOW THRESHOLD (BANK 1) 05195 05FNS02 MONITOR DESCRIPTION The ECM uses 2 sensors mounted before and after the threeway catalytic converter (TWC) to monitor its efficiency.
More informationCamshaft Position "A" Actuator Circuit (Bank 1)
72 2TR-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P0010 Camshaft Position "A" Actuator Circuit (Bank 1) HINT: This DTC relates to the Oil Control Valve (OCV). DCRIPTION The Variable Valve Timing (VVT) system
More informationTRANSAXLE & TRANSMISSION
TRSSS & DRV ST TRSX & TRSSS TTS VT: R009 S ST... 5 DSS D RR WR W... 5 Work low...5 Diagnostic Work Sheet...6 ST D DUST... 8 DDT SRV W R TR UT...8 DDT SRV W R TR UT : recaution for and VT ssembly Replacement...8
More informationDATA LIST/ACTIVE TEST
05-406 DATA LIST/ACTIVE TEST 1. DATA LIST HINT: DIAGNOSTICS - SFI SYSTEM (3MZ-FE)(From August, 2004) Using the hand-held tester DATA LIST allows switch, sensor, actuator and other item values to be read
More informationDTC P0171 SYSTEM TOO LEAN (BANK 1) DTC P0172 SYSTEM TOO RICH (BANK 1) DTC P0174 SYSTEM TOO LEAN (BANK 2) DTC P0175 SYSTEM TOO RICH (BANK 2)
05155 05NZ501 DTC P0171 SYSTEM TOO LEAN (BANK 1) DTC P0172 SYSTEM TOO RICH (BANK 1) DTC P0174 SYSTEM TOO LEAN (BANK 2) DTC P0175 SYSTEM TOO RICH (BANK 2) CIRCUIT DESCRIPTION These DTCs indicate that the
More information1GR-FE ENGINE CONTROL SYSTEM SFI SYSTEM
30 GR-FE ENGINE CONTROL SYSTEM SFI SYSTEM DTC P95 Oxygen (/F) Sensor Signal Stuck Lean (Bank Sensor ) DTC P96 Oxygen (/F) Sensor Signal Stuck Rich (Bank Sensor ) DTC P97 Oxygen (/F) Sensor Signal Stuck
More information1GR-FE ENGINE CONTROL SYSTEM SFI SYSTEM
348 DTC DTC P200 P203 /F Sensor Circuit Slow Response (ank 1 Sensor 1) /F Sensor Circuit Slow Response (ank 2 Sensor 1) DTC P200 indicates malfunctions related to the bank 1 /F sensor. DTC P203 indicates
More informationDTC P0131 HO2S CIRCUIT LOW VOLTAGE (BANK 1/SENSOR 1)
2008 Kia Sorento 3.3L Eng LX DTC P0131 HO2S CIRCUIT LOW VOLTAGE (BANK 1/SENSOR 1) COMPONENT LOCATION Fig 1: Identifying HO2S GENERAL DESCRIPTION In order to control emissions of the CO, HC and x components
More informationBODY CONTROL SYSTEM SECTION BCS CONTENTS ELECTRICAL & POWER CONTROL BCS-1 BASIC INSPECTION... 3 SYSTEM DESCRIPTION... 6 INSPECTION AND ADJUSTMENT...
TR & WR TR ST S Y TR SYSTM TTS S ST... 3 ST USTMT... 3 T SRV W R TR UT (M)...3 T SRV W R TR UT (M) :...3 T SRV W R TR UT (M) : Special Repair Requirement...3 URT (M)...3 URT (M) :...3 URT (M) : Special
More informationFurther systems and diagnosis 5
5.2 Lambda probes Lambda probes measure the oxygen content in the exhaust mixture. They are part of a control loop that continuously ensures that the composition of the fuel/air mix is correct. The mix
More information1GR-FE ENGINE CONTROL SYSTEM SFI SYSTEM
319 P2238 Low (Bank 1 Sensor 1) P2239 High (Bank 1 Sensor 1) P2241 Low (Bank 2 Sensor 1) P2242 High (Bank 2 Sensor 1) P2252 Low (Bank 1 Sensor 1) P2253 High (Bank 1 Sensor 1) P2255 Low (Bank 2 Sensor 1)
More informationSECURITY CONTROL SYSTEM
Y XTRR, RS, R & V URTY T URTY TR SYST TTS RUT... 4 RUTS... 4 recaution for Supplemental Restraint System (SRS) "R " and "ST T R-T- SR"...4 recaution for Work...4 RRT... 5 RRT... 5 Special Service Tool...5
More informationComponent Description
Component Description Component Description IGNITION COIL & POWER TRANSISTOR NFEC0286 NFEC0286S01 The ignition signal from the ECM is sent to and amplified by the power transistor. The power transistor
More information1ZZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM
1ZZ-FE EINE CONTROL SYSTEM SFI SYSTEM 145 DTC P0171 System Too Lean (ank 1) DTC P0172 System Too Rich (ank 1) DCRIPTION The fuel trim is related to the feedback compensation value, not to the basic injection
More information2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM
385 P2237 / Open (Bank 1 Sensor 1) P2238 Low (Bank 1 Sensor 1) P2239 High (Bank 1 Sensor 1) P2240 P2241 / Open (Bank 2 Sensor 1) Low (Bank 2 Sensor 1) P2242 High (Bank 2 Sensor 1) P2252 Low (Bank 1 Sensor
More informationDTC No. DTC Detection Condition Trouble Area
DI68 EINE (2RZFE, 3RZFE) DIB2B01 DTC P0171 System too Lean (Bank 1) DTC P0172 System too Rich (Bank 1) CIRCUIT DESCRIPTION The fuel trim is related to the feedback compensation value, not to the basic
More information2TR-FE ENGINE CONTROL SYSTEM SFI SYSTEM
13 TR-FE ENGINE CONTROL SYSTEM SFI SYSTEM DTC DTC DTC P0136 P0137 P0138 Oxygen Sensor Circuit Malfunction (ank 1 Sensor ) Heated Oxygen Sensor Circuit Low Voltage (ank 1 Sensor ) Oxygen Sensor Circuit
More information