Conductor Protection. results

Transcription

1 Conductor Protection results

2 Conductor Protection Index Dampers Vibration Damper 4R Stockbridge...1 Armor Rods AP8... Aluminum Armor Rods...6 APS... alvanized Steel Armor Rods...8 APAS... AluminumClad Steel Armor Rods...9 Line uards PL5... Aluminum Line uards...10 Protector Rods PR5... Aluminum Protector Rods...12 Cross Reference Armor Rods, Line uards & Protector Rods...13

3 Dampers Vibration Damper 4R Stockbridge Fargo 4R vibration dampers effectively prevent fatigue damage to conductor and static wires caused by windinduced aeolian vibration. The 4R concept improves on the design of the basic Stockbridge damper, significantly increasing the efficiency of converting windinduced energy into heat. The improved design employs unequal weights on messengers of unequal length. This configuration doubles the number of resonant peaks from two generated by the oldstyle Stockbridge damper to four in the improved Fargo 4R. These additional resonant peaks create an envelope of dynamic response that protects the conductor through the entire range of dangerous vibration frequencies. To assure maximum performance, Fargo utilizes a sophisticated computer simulation whose development has been verified by decades of testing and field measurements. This computer model identifies the optimum damper placement on the span. Fargo 4R Vibration Damper System Provides You... Maximum Protection From Wind Induced Conductor Bending Strain The fourresonant peaks include two separate cantilever response modes and two separate rotational response modes of the weight and messenger cable. These peaks also provide maximum energy dissipation to reduce strain over the entire spectrum of dangerous wind velocities. Wide frequency response range optimizes protection of your system Large 19 strand wire and tight strand lay dissipate energy more efficiently Press fit permanent weight attachment technique assures longterm performance Contoured surfaces prevent corona discharge Permanently Secured Weights Tuning Fork Open Weight Design Hotdipped alvanized Iron Large Weight Long Moment Arm Aluminum Vise Clamp Tight Strand Lay alvanized 19wire Steel Messenger Cable Short Moment Arm Hotdipped alvanized Iron Small Weight Comprehensive Application Program for Optimum Performance Provides precise selection and placement through our proprietary computer simulation Computer program based on a mathematical model verified by decades of laboratory testing and field vibration measurements Precisely identifies the vibration performance characteristics of transmission lines Determines dangerous tension levels for existing or proposed spans Identifies the frequency range, tension level and span lengths requiring damper protection Identifies proper damper placement for required vibration energy dissipation Results of the above analysis for conductors and shield wires are available online at: Fargo 4R Damper Application Software Contoured Surfaces 1 See the Reference Materials section of this catalog for a detailed program description.

4 Dampers Vibration Damper 4R Stockbridge Messenger Cable: Materials and stranding are selected to obtain the best energy absorption characteristics. The galvanized steel messenger is manufactured to rigid engineering standards. Fargo 4R vibration dampers effectively prevent fatigue damage to conductor and static wires caused by windinduced aeolian vibration. Weights: Uniquely shaped so that the resonant peaks are effectively distributed over the desired frequency range. All weights are given a corrosionresistant finish and have smooth surfaces and rounded edges to eliminate possible corona discharge. C Clamp: The bolted clamp permits easy installation on a wide range of conductor sizes. Aluminum clamping bolt ensures that damper clamp remains tight as conductor temperature changes with current load cycling. B A Product Data 2 Damper Catalog Number (1) Bare Conductor/Cable Diameter Range (2) in. (mm) ( ) ( ) ( ) ( ) ( ) Conductor/Cable Dia. Clamp Over Armor Bolt Rods Range (2) Torque in. (mm) ftlb ( ) ( ) ( ) ( ) ( ) Dimensions inches (mm) A B C Weight Each lb (kg) 11.1 (282) 16.1 (409) 16.1 (409) 20.0 (508) 20.0 (508) 21.9 (556) 21.9 (556) 24.0 (610) 24.0 (610) 2.38 (60) 2.69 (68) 2.91 (74) 2.91 (74) 3.20 (81) 3.78 (96) 4.20 (107) 5.92 (150) 6.30 (160) 1.75 (44) 1.75 (44) 2.26 (57) 2.26 (57) 2.26 (57) 2.82 (72) 2.82 (72) 3.54 (90) 3.54 (90) 2.8 (1.3) 4.8 (2.2) 5.0 (2.3) 9.0 (4.1) 9.4 (4.3) 15.7 (7.1) 16.0 (7.3) 22.0 (10) 22.5 (10.2) Std Pkg Qty (1) To specify Torque Head/Break Away bolt option, add suffix O to catalog number. (2) Recommended conductor/cable size range limits. Physical clamp range may be slightly larger.

5 Dampers 4R Damper Installation Instructions Spacing Deadend Spacing Suspension Clamp Spacing Suspension Clamp with Armor Rods Spacing 3 Formed Wire Suspension NOTE: Dampers shall be located from the center of the damper clamp to either the dead end or the suspension support as shown above. The orientation of the damper weights along the conductor is optional. For convenience, orient the damper such that the clamp bolt head faces the installer. When only one damper is required per conductor per span, it can be installed at either span extremity when the support hardware is identical. When support hardware differs, place the damper at the suspension structure. When two dampers are required per conductor per span, the preferred placement is one at each span extremity.

6 Armor Rods & Line uards Industry Competitive Price, quality & lead time Look, feel & function ACSR/ACSS; ACSR/ACSS TW; AAC, AAAC; ACAR Production EHV rated, made to order 4 Inventory available for popular sizes Sample orders welcomed Product Specs Aluminum Alloy Right Hand Lay Ball Ends Chamfered Ends < Add E Suffix for EHV Rod End Add D Prefix for Double Supported Length (For rod diameters < 0.25 only)

7 Armor Rods & Line uards Materials: Rods manufactured from either aluminum covered steel, aluminum alloy or galvanized steel Color code and center mark establishes alignment of rods during application and identifies conductor size Identification tag identifies catalog number and conductor details Industry Knowledge: Armor Rods and Line uards have overlapping purpose to protect conductors from fatiguedamage by providing a stiffening support for suspended conductors. They also protect from abrasiondamage at attachment points by providing a buffer between the conductor and the clamping connector. They are both made up of sets of individual rods of the same diameter. When installed, the set of individual rods grip rigidly onto their respective conductors. Once each rod of the respective set has been installed, the set should evenly enclose the conductor along the length of the rods. Physically, the line guard sets are shorter in length and the individual rods are smaller in diameter. The application for line guards is typically found on light transmission lines with shorter spans, smaller conductor sizes and lower voltages. Armor Rods are recommended for applications where the conductor is clamped or suspended with bolted type connectors. Product Offerings:* Aluminum Armor Rods Aluminum Line uards Aluminum Protector Rods alvanized Steel Rods AlumoWeld Steel Rods 250 C for respective suspension clamp & conductor application* Application O.D. = (Rod O.D. X 2) + Conductor O.D. Armor Rods 1. Fargo Armor Rods are intended to protect conductors from stress and damage which can be caused by a bend, compression, abrasion or arc over. They are also designed to repair conductors which have sustained < 50% outer strand damage.* 2. Armor Rods should be considered as minimum protection for clamp style supports or suspension hardware for spans > 300 feet. 3. Armor Rods are designed to provide an extra degree of protection to the conductor at support points, not act as vibration dampers. In areas where vibration is suspected or known to occur, the use of Fargo 4R Dampers is recommended. eneral Recommendations Line uards 1. Fargo Line uards are intended to provide an extra degree of protection for the conductor against abrasion and arc over. They are also designed to repair conductors which have sustained < 25% outer strand damage.* 2. Line uards should be considered as minimum protection for handtied spans 300 feet in urban areas with no history of vibration. 3. Line uards should be considered as a cost saving alternate to Armor Rods when applicable. Note: HPS Distribution Ties are recommended as an improvement over Line uards and hand ties, providing a stronger and more uniform tie. 5 *The degree of protection required is dependent upon line design, tension, temperature, and wind conditions. Contact HPS Connectors Business Unit for specific recommendations.

8 Conductor Protection Armor Rods For use on stranded aluminum and aluminum composite conductors, including hightemperature conductor designs. (4) ALUMINUM AP8 Material: aluminum alloy 6 Catalog Number AP8114 DAP8114 AP8115 DAP8115 AP8116 DAP8116 AP8117 DAP8117 AP8118 DAP8118 AP8119 DA08119 AP8120 DAP8120 AP8121 DAP8121 AP8122 DAP8122 AP8123 DAP8123 AP8124 DAP8124 AP8125 DAP8125 AP8126 DAP8126 AP8127 DAP8127 AP8128 DAP8128 AP8129 DAP8129 AP8130 DAP8130 AP (18.8) AP (19.9) AP (20.7) AP (21.5) AP (23.1) AP (23.6) NOTES: (1) Righthand lay standard. Product Data and Conductor Size Conductor Dia. Nominal Conductor Size Applied Rod Rods Range In. (mm) (AW or KCMIL) Length Dia. Per Sets Per Wt. Per (in.) (in.) Set Color (lbs.) Code Min. Max. ACSR/ACSS AAC, AAAC (7.8) (8.3) #2 (6/1) 44 56(D) Red (8.3) (8.8) # (D) Blue (8.8) (9.3) #1 (6/1) 48 60(D) reen (9.3) (9.9) 1/ (D) Black (9.9) (10.5) 1/0 (6/1) 52 64(D) Yellow (10.5) (11.1) 2/ (D) Brown (11.1) (11.8) 2/0 (6/1) 54 66(D) Blue (11.8) (12.4) 3/ (D) reen (12.5) (13.2) 3/0 (6/1) 56 68(D) Orange (13.3) (14.0) 4/ (D) Black (14.0) (14.9) 4/0 (6/1) (D) Red (14.9) (15.4) (D) Black (15.4) (16.0) (18/1) 64 76(D) Purple (16.0) (16.6) (26/7) 64 76(D) Yellow (16.7) (17.2) (D) Brown (17.3) (17.9) (18/1) 68 80(D) Blue (17.9) (18.8) (26/7) (D) reen (19.9) (18/1) Orange (20.7) (26/7) 477, Purple (21.5) Red (23.0) 477 (26/7) Blue (23.6) (26/7) reen (24.8) (30/7) 605 (26/7) White (2) For aluminum conductor types & sizes not listed above, select rod set based on dia. range to accomodate conductor. (3) Applied O.D. of conductor with rods, for suspension clamp selection, equals conductor diameter plus two times rod dia. (4) Maximum conductor temperature limits vary with suspension clamp designs. See catalog Reference Data secton for guidelines.

9 Conductor Protection Armor Rods For use on stranded aluminum and aluminumcomposite conductors, including hightemperature conductor designs.(4) ALUMINUM AP8 For EHV applications, add suffix E to catalog numbers to Specify. Example AP8146E Material: aluminum alloy Catalog Number AP (24.8) AP (25.8) AP (26.3) AP (27.1) AP (27.9) AP (29.0) AP (29.5) AP (30.7) AP (32.3) AP (33.7) AP (35.3) AP (36.6) AP (38.3) AP (40.1) AP (42.0) AP (43.9) AP (46.0) NOTES: (1) Righthand lay standard. (2) For aluminum conductor types & sizes not listed above, select rod set based on dia. range to accomodate conductor. (3) Applied O.D. of conductor with rods, for suspension clamp selection, equals conductor diameter plus two times rod dia. (4) Maximum conductor temperature limits vary with suspension clamp designs. See catalog Reference Data secton for guidelines. Conductor Dia. Range In. (mm) Nominal Conductor Size (AW or KCMIL) Min. Max. ACSR/ACSS AAC, AAAC (25.8) Applied Length (in.) Rod Dia. (in.) Rods Per Set Sets Per Wt. Per (lbs.) Color Code 636 (24/7) (26/7) 666 (24/7) (26/7) Yellow (26.3) (30/19) Brown (27.0) (26/7) 795 (45/7) Blue (27.9) 795 (24/7) reen (28.9) 795 (26/7) Orange (29.5) 954 (36/1) Purple (30.7) (32.2) (33.7) (35.3) (36.6) 954 (45/7) (54.7) (45/7) Red (54/7) 1113 (45/7) Black 1113 (54/19) (45/7) White (54/19) /7 (54/19) (45/7) Yellow (54/19) 1434 (45/7) Brown (38.3) 1590 (45/7) Blue (40.1) 1590 (54/19) reen (41.9) 1780 (84/19) Orange (43.9) (72/7) Purple (45.9) Product Data and Conductor Size 2167 (72/7) 2156 (84/19) Red (48.2) 2515 (76/19) Black 7

10 Conductor Protection Armor Rods For use on galvanized, strandedsteel cables with lefthand lay. Typical application is on transmission line overhead shield wires. STEEL APS Material: galvanized steel Catalog Number APS (7.8) APS (8.8) APS (10.5) APS (12.5) NOTES: Cable Dia. Range In. (mm) Min. Max. (1) Lefthand lay standard. Nominal Cable Diameter (in.) Product Data Applied Length (in.) (2) Applied O.D. of conductor with rods, for suspension clamp selection, equals conductor diameter plus two times rod dia. (3) alvanized steel armor rods may be suitable for application on other cable types, Consult factory for specific information. Rod Dia. (in.) Rods Per Set Sets Per Wt. Per (lbs.) Color Code (8.3) 5/ Black (9.5) 3/ Orange (11.1) 7/ reen (13.2) 1/ Blue 8

11 Conductor Protection Armor Rods For use on Alumoweld (aluminumclad, strandedsteel) cables with lefthand lay. Typical application is on transmission line overhead shield wires. STEEL APAS Material: aluminumclad steel Catalog Number APAS0710 DAPAS0710 APAS0079 DAPAS0079 APAS0078 DAPAS0078 APAS018M DAPAS018M APAS0077 DAPAS0077 APAS0076 DAPAS0076 APAS0075 DAPAS0075 Cable Dia. Range In. (mm) Min. Max (7.5) (8.5) (9.5) (10.4) (10.8) (12.1) (13.6) NOMINAL CABLE SIZE INCHES, AWSTR M(UTS klb) Product Data Applied Length (in.) Rod Dia. (in.) Rods Per Set Sets Per Wt. Per (lbs.) Color Code (8.0) 5/16, 7#10, 3#7, 10M 46 58(D) Black (8.9) 7#9, 3#6, 12.5M 50 62(D) Yellow (10.0) 3/8, 7#8, 3#5, 16M 50 62(D) Orange (10.8) 18M 54 66(D) Black (11.4) 7/16, 7#7, 20M 56 68(D) reen (12.8) 1/2, 7# (D) Blue (14.4) 9/16, 7# (D) Yellow NOTES: (1) Lefthand lay standard. (2) Applied O.D. of conductor with rods, for suspension clamp selection, equals conductor diameter plus two times rod dia. (3) Alumoweld is a registered trademark of the Copperweld Co. 9

12 Conductor Protection Line uards For use on stranded aluminum and aluminum composite conductors, including hightemperature conductor designs. (4) ALUMINUM PL5 Material: aluminum alloy 10 Catalog Number PL5130 DPL5130 PL5131 DPL5131 PL5132 DPL5132 PL5133 DPL5133 PL5134 DPL5134 PL5135 DPL5135 PL5136 DPL5136 PL5137 DPL5137 PL5138 DPL5138 PL5139 DPL5139 PL5140 DPL5140 PL5141 DPL5141 PL5142 DPL5142 PL5143 DPL5143 PL5144 DPL5144 PL5145 DPL5145 PL5146 DPL5146 PL5147 DPL5147 PL5148 DPL5148 PL5149 DPL5149 PL5150 DPL5150 PL5151 DPL5151 Product Data and Conductor Size Conductor Dia. Nominal Conductor Size Applied Rod Rods Range In. (mm) (AW or KCMIL) Length Dia. Per Sets Per Wt. Per (in.) (in.) Set Color (lbs.) Code Min. Max. ACSR/ACSS AAC, AAAC (7.4) (7.8) # (D) Purple (7.8) (8.3) #2 (6/1) # (D) Red (8.3) (8.8) # (D) Blue (8.8) (9.3) #1 (6/1) 23 35(D) reen (9.3) (9.9) 1/ (D) Black (9.9) (10.5) 1/0 (6/1) 1/ (D) Yellow (10.5) (11.1) 2/ (D) Brown (11.1) (11.8) 2/0 (6/1) 27 39(D) Blue (11.8) (12.4) 3/ (D) reen (12.5) (13.2) 3/0 (6/1) (D) Orange (13.3) (14.0) 4/ (D) Black (14.0) (14.9) 4/0 (6/1) (D) Red (14.9) (15.4) (D) Black (15.4) (16.0) (18/1) (D) White (16.0) (16.6) (26/7) (D) Yellow (16.7) (17.2) (D) Brown (17.3) (17.9) (18/1) (D) Blue (17.9) (18.8) (26/7) (D) reen (18.8) (19.9) (18/1) (26/7) (D) Orange (20.1) (21.3) (30/7) 477 (18/1) (D) Purple (21.4) (22.8) 477 (26/7) (30/7) 556.5, (D) Blue (22.8) (24.2) (26/7) (30/7) 636 (18/1) (D) reen NOTES: (1) Righthand lay standard. (2) For aluminum conductor types & sizes not listed above, select rod set based on dia. range to accomodate conductor. (3) Applied O.D. of conductor with rods, for suspension clamp selection, equals conductor diameter plus two times rod dia. (4) Maximum conductor temperature limits vary with suspension clamp designs. See catalog Reference Data secton for guidelines.

13 Conductor Protection Line uards Line uards for conductors 1.0 inch diameter or larger are available for EHV application. Add suffix E to catalog number to specify. Example PL5155E ALUMINUM PL5 Catalog Number PL5152 DPL5152 PL5153 DPL5153 PL5154 DPL5154 PL5155 DPL5155 PL5156 DPL5156 PL5157 DPL5157 PL5158 DPL5158 PL5159 DPL5159 PL5160 DPL5160 PL5161 DPL5161 PL5162 DPL5162 PL5163 DPL5163 NOTES: (1) Righthand lay standard. Conductor Dia. Nominal Conductor Size Applied Rod Rods Range In. (mm) (AW or KCMIL) Length Dia. Per Sets Per Wt. Per (in.) (in.) Set Color (lbs.) Code Min. Max. ACSR/ACSS AAC, AAAC (24.3) (25.0) 605 (26/7) 636 (24/7) (D) White (25.1) (25.8) 636 (26/7) 666 (24/7) (26/7) (D) Yellow (25.8) (27.0) 636 (30/19) 715 (26/7) 795 (45/7) (D) Brown (27.1) (27.9) (30/19) 795 (54/7) 874.5, (D) reen (27.9) (29.3) 795 (26/7) (30/19) (D) Orange (29.3) (30.7) 954 (45/7) (54/7) (D) Purple (30/19) (30.7) (32.2) (45/7) (54/7) 1113 (45/7) 1113, (D) Black (32.2) (33.7) (35.3) (36.6) (38.3) (33.7) (35.3) Product Data and Conductor Size (continued) 1113 (54/19) (45/7) (D) White (54/19) 1272 (45/7) (54/19) (45/7) , (D) Yellow (36.6) (54/19) 1431 (45/7) (D) Brown (38.3) 1431 (54/19) 1590 (45/7) 1590, (D) Blue (40.0) 1590 (54/19) (D) reen (2) For aluminum conductor types & sizes not listed above, select rod set based on dia. range to accomodate conductor. (3) Applied O.D. of conductor with rods, for suspension clamp selection, equals conductor diameter plus two times rod dia. (4) Maximum conductor temperature limits vary with suspension clamp designs. See catalog Reference Data secton for guidelines. 11

14 Conductor Protection Protector Rods Primary application as a mechanical reinforcement layer for mounting dampers or other devices on ACSS conductors or OPW cables where suspension support reinforcing rods are not available to mount damper or device. ALUMINUM PR5 For EHV applications, add suffix E to catalog numbers to Specify. Example PR5158E 12 Catalog Number PR (12.1) PR (13.6) PR (14.9) PR (15.7) PR (17.0) PR (18.4) PR (20.8) PR (22.8) PR (24.3) PR (25.9) PR (27.1) PR (27.9) PR (30.0) PR (33.0) PR (36.0) PR (39.2) PR5164 Conductor / OPW Dia. Range In. (mm) Nominal Conductor Size (AW or KCMIL) Min. Max. ACSS ACSS/TW (42.8) Applied Length (in.) Rod Dia. (in.) Rods Per Set Sets Per Wt. Per (lbs.) (13.5) Blue Color Code (14.9) reen (15.7) Orange (16.9) (26/7) (30/7) Purple (18.3) (26/7) (17/7) T Red (20.7) (26/7) (30/7) 477 (18/7) T (18/7) T Black (22.8) 477 (26/7) (30/7) 477 (16/7) T (20/7) T White (24.2) (26/7) (30/7) 636 (20/7) T Yellow (25.9) (27.0) 636 (24/7) (26/7) (30/19) 666 (24/7) (26/7) 715 (24/7) (26/7) 795 (45/7) 795 (21/7) T (20/7) T Brown 795 (22/19) T (33/7) T Blue (27.9) 795 (24/7) (54/7) 954 (21/7) T reen (26/7) (30/19) (33/7) T7 (30.0) 954 (45/7) (21/7) T Orange 1113 (33/7) T (33.0) (35.9) (39.2) (42.8) 954 (54/7) (30/19) (45/7) (54/7) 1113 (45/7) (54/19) (45/7) (54/19) 1272 (45/7) (54/19) (45/7) (54/19) 1431 (45/7) (54/19) 1590 (45/7 Product Data and Conductor Size 1113 (39/19) T (39/19) T (33/7) T7 (39/19) T (33/7) T Purple (39/19) T (36/7) T Blue 1590 (42/19) T (38/19) T Yellow 1590 (54/19) 1780 (84/19) 2156 (64/19) T Brown 1.84 (46.7) 2156 (84/19) Blue NOTES: (1) Righthand lay standard. (2) For conductor/cable sizes not listed above, select rod set based on cable dia. range. (3) Applied O.D. of conductor/cable with rods equals cable diameter plus two times rod diameter. (4) Maximum conductor temperature limits vary with suspension clamp designs. Consult factory for information.

15 Cross Reference: Armor Rods, Line uards & Protector Rods 13 results

16 Armor Rods Aluminum Product Data and Conductor Size Conductor Dia. In. (mm) Nominal Conductor Size (AW or kcmil) HPS PLP DULMISON HELICAL Min. Max. ACSR/ACSS ACSR/ACSS TW AAC, AAAC ACAR (7.8) (8.3) #2 6/1 AP8114 AR0114 AAR0785 AAR (8.3) (8.8) #1 AP8115 AR0115 AAR0830 AAR (8.8) (9.3) #1 6/1 AP8116 AR0116 AAR0880 AAR (9.3) (9.9) 1/0 AP8117 AR0117 AAR0930 AAR (9.9) (10.5) 1/0 6/1 AP8118 AR0118 AAR0990 AAR (10.5) (11.1) 2/0 AP8119 AR0119 AAR1050 AAR (11.1) (11.8) 2/0 6/1 AP8120 AR0120 AAR1110 AAR (11.8) (12.4) 3/0 AP8121 AR0121 AAR1180 AAR (12.5) (13.2) 3/0 6/1 AP8122 AR0122 AAR1245 AAR (13.3) (14.0) 4/0 AP8123 AR0123 AAR1325 AAR (14.0) (14.9) 4/0 6/1 250 AP8124 AR0124 AAR1400 AAR (14.9) (15.4) T AP8125 AR0125 AAR1490 AAR (15.4) (16.0) /1 AP8126 AR0126 AAR1540 AAR (16.0) (16.6) /7 AP8127 AR0127 AAR1605 AAR (16.7) (17.2) T AP8128 AR0128 AAR1665 AAR (17.3) (17.9) / T23 AP8129 AR0129 AAR1725 AAR (17.9) (18.8) / T AP8130 AR0130 AAR1790 AAR (18.8) (19.9) /1 477 T13 AP8131 AR0131 AAR1880 AAR (19.9) (20.7) /7 477 T16 477, AP8132 AR0132 AAR1990 AAR (20.7) (21.5) 477 T T13 AP8133 AR0133 AAR2070 AAR537

17 Armor Rods Aluminum Product Data and Conductor Size (continued) Conductor Dia. In. (mm) Nominal Conductor Size (AW or kcmil) Min. Max. ACSR/ACSS ACSR/ACSS TW AAC, AAAC ACAR HPS PLP DULMISON HELICAL (21.5) (23.0) 480 5/ T T AP8134 AR0134 AAR2150 AAR (23.1) (23.6) /7 636 T T AP8135 AR0135 AAR2305 AAR (23.6) (24.8) / / AP8136 AR0136 AAR2360 AAR (24.8) (25.8) /7 26/ /7 26/ T T13, T AP8137 AP8137E (25.8) (26.3) / AP8138 AP8138E (26.3) (27.0) / /7 964 T AP8139 AP8139E (27.1) (27.9) /7 964 T13 AP8140 AP8140E (27.9) (28.9) / T T AP8141 AP8141E (29.0) (29.5) / T7 AP8142 AP8142E (29.5) (30.7) / / (30.7) (32.2) / / (32.3) (33.7) / / (33.7) (35.3) / /7 54/ / (35.3) (36.6) / / T7, T T T T7, T T T AP8143 AP8143E AP8144 AP8144E T T AP8145 AP8145E T T AP8146 AP8146E 1590 T T AP8147 AP8147E (36.6) (38.3) / T T AP8163 AP8163E (38.3) (40.1) / T AP8164 AP8164E (40.1) (41.9) / T AP8165 AP8165E (42.0) (43.9) /7 AP8166 AP8166E (43.9) (45.9) / / T AP8167 AP8167E (46.0) (48.2) / AP8168 AP8168E AR0137 AR0500 AR0138 AR0501 AR0139 AR0502 AR0140 AR0503 AR0141 AR0504 AR0142 AR0505 AR0143 AR0506 AR0144 AR0507 AR0145 AR0508 AR0146 AR0509 AR0147 AR0510 AR0163 AR0511 AR0164 AR0512 AR0165 AR0513 AR0166 AR0514 AR0167 AR0516 AR0168 AR0517 AAR2480 AAR2480E AAR2585 AAR2585E AAR2630 AAR2630E AAR2705 AAR2705E AAR2790 AAR2790E AAR2895 AAR2895E AAR2950 AAR2950E AAR3070 AAR3070E AAR3225 AAR3225E AAR3375 AAR3375E AAR3535 AAR3535E AAR3660 AAR3660E AAR3835 AAR3835E AAR4010 AAR4010E AAR4195 AAR4195E AAR4390 AAR4390E AAR4595 AAR4595E AAR541 AAR542 AAR543 AAR544 AAR545 AAR546 AAR547 AAR548 AAR549 AAR550 AAR551 AAR552 AAR553 AAR554 AAR555 AAR556 AAR557 15

18 Armor Rods Alumunum, Double Suspension Product Data and Conductor Size Conductor Dia. In. (mm) Nominal Conductor Size (AW or kcmil) HPS PLP DULMISON HELICAL Min. Max. ACSR/ACSS ACSR/ACSS TW AAC, AAAC ACAR (7.8) (8.3) #2 6/1 DAP8114 AR0314 DAAR0785 AAR (8.3) (8.8) #1 DAP8115 AR0315 DAAR0830 AAR (8.8) (9.3) #1 6/1 DAP8116 AR0316 DAAR0880 AAR (9.3) (9.9) 1/0 DAP8117 AR0317 DAAR0930 AAR (9.9) (10.5) 1/0 6/1 DAP8118 AR0318 DAAR0990 AAR (10.5) (11.1) 2/0 DAP8119 AR0319 DAAR1050 AAR (11.1) (11.8) 2/0 6/1 DAP8120 AR0320 DAAR1110 AAR (11.8) (12.4) 3/0 DAP8121 AR0321 DAAR1180 AAR (12.5) (13.2) 3/0 6/1 DAP8122 AR0322 DAAR1245 AAR (13.3) (14.0) 4/0 DAP8123 AR0323 DAAR1325 AAR (14.0) (14.9) 4/0 6/1 250 DAP8124 AR0324 DAAR1400 AAR (14.9) (15.4) T DAP8125 AR0325 DAAR1490 AAR (15.4) (16.0) /1 DAP8126 AR0326 DAAR1540 AAR (16.0) (16.6) /7 DAP8127 AR0327 DAAR1605 AAR (16.7) (17.2) T DAP8128 AR0328 DAAR1665 AAR (17.3) (17.9) 303 5/ T23 DAP8129 AR0329 DAAR1725 AAR (17.9) (18.8) / T DAP8130 AR0342 DAAR1790 AAR634

19 Armor Rods alvanized Steel Product Data and Conductor Size Conductor Dia. In. (mm) HS & EHS Cable HPS PLP DULMISON HELICAL Min. Max (7.8) (8.3) 5/16" APS0516 AR1128 SAR0785 AR (8.8) (9.5) 3/8" APS0038 AR1130 SAR0880 AR (10.5) (11.1) 7/16" APS0716 AR1133 SAR1050 AR (12.5) (13.2) 1/2" APS0012 AR1139 SAR1245 AR534 Armor Rods AlumunumClad Steel (Alumoweld ) Product Data and Conductor Size Conductor Dia. In. (mm) HS & EHS Cable HPS PLP DULMISON HELICAL Min. Max (7.5) (8.0) 5/16", 7#10, 3#7, 10M APAS0710 AR2124 AWAR0750 AWAR (8.5) (8.9) 7#9, 3#6, 12.5M APAS0079 AR2126 AWAR0850 AWAR (9.5) (10.0) 3/8", 7#8, 3#5, 16M APAS0078 AR2128 AWAR0950 AWAR (10.4) (10.8) 18M AP2130 AR2130 AWAR1040 AWAR (10.8) 0.45 (11.4) 7/16", 7#7, 20M APAS0077 AR2131 AWAR1080 AWAR (12.1) (12.8) 1/2", 7#6 APAS0076 AR2133 AWAR1210 AWAR (13.6) (14.4) 9/16", 7#5 APAS0075 AR2135 AWAR1360 AWAR532

20 Line uards Aluminum Product Data and Conductor Size 18 Conductor Dia. In. (MM) Nominal Conductor Size, (AW or kcmil) Min. Max. ACSR/ACSS ACSR/ACSS TW AAC, AAAC ACAR (7.4) (7.8) #2 PL5130 DPL (7.8) (8.3) #2 6/1 PL5131 DPL (8.3) (8.8) #1 PL5132 DPL (8.8) (9.3) #1 6/1 PL5133 DPL (9.3) (9.9) 1/0 PL5134 DPL (9.9) (10.5) 1/0 6/ PL5135 DPL (10.5) (11.1) 2/0 PL5136 DPL (11.1) (11.8) 2/0 6/1 PL5137 DPL (11.8) (12.4) 3/0 PL5138 DPL (12.5) (13.2) 3/0 6/ PL5139 DPL (13.3) (14.0) 4/0 PL5140 DPL (14.0) (14.9) 4/0 6/1 250 PL5141 DPL (14.9) (15.4) T PL5142 DPL (15.4) (16.0) /1 PL5143 DPL (16.0) (16.6) / PL5144 DPL (16.7) (17.2) T PL5145 DPL (17.3) (17.9) / T23 PL5146 DPL (17.9) (18.8) / T PL5147 DPL (18.8) (20.1) /1 26/7 477 T13 T PL5148 DPL5148 HPS PLP DULMISON HELICAL M0130 M0313 M0131 M0314 M0132 M0315 M0133 M0316 M0134 M0317 M0135 M0318 M0136 M0319 M0137 M0320 M0138 M0321 M0139 M0322 M0140 M0323 M0141 M0324 M0142 M0325 M0143 M0326 M0144 M0327 M0145 M0328 M0146 M0329 M0147 M0330 M0148 M0331 AL0735 DAL0735 AL0785 DAL0785 AL0830 DAL0830 AL0880 DAL0880 AL0930 DAL0930 AL0990 DAL0990 AL1050 DAL1050 AL1110 DAL1110 AL1180 DAL1180 AL1245 DAL1245 AL1325 DAL1325 AL1400 DAL1400 AL1490 DAL1490 AL1540 DAL1540 AL1605 DAL1605 AL1665 DAL1665 AL1725 DAL1725 AL1790 DAL1790 AL1880 DAL1880 AL517 AL617 AL518 AL618 AL519 AL619 AL520 AL620 AL521 AL621 AL522 AL622 AL523 AL623 AL524 A;624 AL525 AL615 AL526 AL626 AL527 AL627 AL528 AL628 AL529 AL629 AL530 AL630 AL531 AL631 AL532 AL632 AL533 AL633 AL534 AL634 AL535 AL635

21 Line uards Aluminum Product Data and Conductor Size (continued) Conductor Dia. In. (MM) Nominal Conductor Size, (AW or kcmil) Min. Max. ACSR/ACSS ACSR/ACSS TW AAC, AAAC ACAR (20.1) (21.3) /7, /1 477 T23, T PL5149 DPL (21.4) (22.8) /7 30/ T16, T T13, 636 T , PL5150 DPL (22.8) (24.2) /7 30/ /1 636 T16, T PL5151 DPL (24.3) (25.0) /7, / T13, 795 T PL5152 DPL (25.1) (25.8) /19, / /7 26/ T16, 795 T PL5153 DPL (25.8) (27) / /7, /7 954 T PL5154 DPL (27.1) (27.9) / /7 954 T , 900 PL5155 DPL (27.9) (29.3) /7 30/ T T7 T T PL5156 DPL (29.3) (30.7) /7 54/ T T13, T PL5157 DPL (30.7) (32.2) / /7 54/ / (32.2) (33.7) / / (33.7) (35.3) / /7 54/ / T13, T T7 T T7 1113, PL5158 DPL T T PL5159 DPL & T & 1590 T , PL5160 DPL (35.3) (36.6) / / & 1622 T PL5161 DPL (36.6) (38.3) / / T T PL5162 DPL5162 HPS PLP DULMISON HELICAL M0149 M0332 M0150 M0333 M0151 M0334 M0152 M0335 M0153 M0336 M0154 M0337 M0155 M0338 M0156 M0339 M0157 M0340 M0158 M0341 M0159 M0342 M0160 M0343 M0161 M0344 M0162 M0345 AL2015 DAL2015 AL2135 DAL2135 AL2285 DAL2285 AL2425 DAL2425 AL2505 DAL2505 AL2585 DAL2585 AL2705 DAL2705 AL2790 DAL2790 AL2930 DAL2930 AL3070 DAL3070 AL3225 DAL3225 AL3375 DAL3375 AL3535 DAL3535 AL3660 DAL3660 AL536 AL636 AL537 AL637 AL538 AL638 AL539 AL639 AL540 AL640 AL541 AL641 AL542 AL642 AL543 AL643 AL544 AL644 AL545 AL645 AL546 AL646 AL547 AL647 AL548 AL648 AL549 AL649 19

22 Protector Rods Aluminum Conductor Dia. In. (MM) Product Data and Conductor Size Nominal Conductor Size, (AW or kcmil) Min. Max. ACSS ACSS TW (12.1) (13.5) PR5139 PR (13.6) (14.9) PR5141 PR (14.9) (15.7) PR5142 PR (15.7) (16.9) /7 PR5144 PR (17.0) (18.3) / T23 PR5146 PR (18.4) (20.7) /7 477 T13, T16 PR5148 PR (20.8) (22.8) /7, 26/7 477 T23 PR5150 PR (22.8) (24.2) /7, 26/7 636 T16, T23 PR5151 PR (24.3) (25.9) /7, 26/ /7, 26/7 765 T13, T16 PR5152 PR (25.9) (27.0) /7, 26/ /7 795 T23 PR5154 PR (27.1) (27.9) /7, 54/7 954 T13 PR5155 PR0155 HPS PLP (27.9) (30.0) /7, 30/ / (30.0) (33.0) /7, / /7, 54/ (33.0) (35.9) /7, 54/ /7, 54/19, / T T13 PR5156 PR T13, T7, T T13, 1272 T7, T13, T7 PR5158 PR T13, T T7, T13 PR5160 PR (36.0) (39.2) / / T13, 1780 T8 PR5162 PR (39.2) (42.8) / / T13, 2156 T8 PR5163 PR (42.8) (46.7) / / T8 PR5164 PR0164