Tu-Wire Overview. Fluorescent Dimming Ballasts Tu-Wire 5% High-Performance Dimming
|
|
- Myron York
- 6 years ago
- Views:
Transcription
1 Overview Tu-wire ballasts are primarily intended for retrofit applications where fluorescent dimming must be achieved without changing the existing switching wiring scheme. Tu-wire ballasts require only two input wires (hot and neutral), used both for power and dimming control. Tu-wire ballasts offer high performance dimming from 00% down to 5% for linear and compact fluorescent lamps. eatures ontinuous, flicker-free dimming from 00% to 5% -wire line voltage control for wiring simplicity Models for T4 compact and T8 lamp types Programmed rapid start design will preheat lamp cathodes before applying full arc voltage Lamps turn on to any dimmed level without flashing to full brightness in (5 mm) high, low-profile design for use in low-profile architectural fixtures requency of operation ensures that ballast does not interfere with infrared devices operating between 38 and 4 kz nrush current limiting circuitry eliminate circuit breaker tripping, switch arcing, and relay failure nd-of-lamp-life protection circuitry ensures safe oper-ation throughout entire lamp life cycle for T4 lamps Ultra quiet operation Protected from shorts between any one lamp lead and ground Low-line voltage protection circuitry prevents damage to the ballast or lamps if the ballast is connected to an incompatible dimmer 00% compatible with all Lutron -wire fluorescent controls 00% performance tested at factory esigned and assembled in the U.S.. allasts that dim T4 compact fluorescent lamps are intended for factory installation by OM fixture manufacturers 5-year limited warranty with Lutron field service commissioning (3-year standard warranty) from date of purchase, case type 3.00 in (76 mm) W x.00 in (5 mm) x 4.90 in (4 mm) L, case type 3.00 in (76 mm) W x.00 in (5 mm) x 6.75 in (7 mm) L, case type.8 in (30 mm) W x.00 in (5 mm) x 8.00 in (457 mm) L c SPTON SUMTTL Page
2 Specifications c Performance imming Range: 00% to 5% measured relative light output (RLO) Lamp Starting: programmed rapid start Minimum Lamp Starting Temperature: 50 (0 ) mbient Temperature Operating Range: 50 to 40 (0 to 60 ) Relative umidity: maximum 90% noncondensing Operating Voltage: 0 V~, 60 z nominal line Lamp urrent rest actor: less than.7 Lamp licker: none visible Light Output: constant ±5% light output for line voltage variations of ±0% Lamp Life: average lamp life meets or exceeds rating of lamp manufacturer allast actor: greater than 0.85 Power actor: greater than 0.95 tal armonic istortion (T): less than 0% at full light output requency of Operation: greater than 4 kz Maximum nrush urrent: 7 per ballast at 0 V~ Sound Rating: naudible in a 7 d ambient Maximum allast ase Temperature: 67 (75 ) Standards alifornia nergy ommission () Listed UL Listed (evaluated to the requirements of UL935) S certified (evaluated to the requirements of. No. 74) * lass P thermally protected Meets NS 8. igh requency allast Standard Meets Part 8 non-consumer requirements for M/R emissions -lamp ballasts for 4-pin compact fluorescent lamps meet Part 8 consumer requirements for M/ R emissions ( : JP00) Meets NS 6.4 ategory surge protection standards up to and including 6 kv Manufacturing facilities employ S reduction practices that comply with the requirements of NS/S S0.0 Lutron Quality Systems registered to SO * or all models except 5 W T8 SPTON SUMTTL Page
3 allast Models c VOLTS Lamp Type T4 4-pin Quad-tube or Triple-tube Lamp Watts (length) Lamps per ballast ase Type allast urrent () Model Number 8 W 0.4 W-T48-0--S (studded) W-T48-0- (non-studded) 6 W 0.7 W-T46-0--S (studded) W-T46-0- (non-studded) / in (.7 mm) diameter T4 4-pin Triple-tube 0.53 W-T46-0--S (studded) W-T46-0- (non-studded) 3 W 0.33 W-T43-0--S (studded) W-T43-0- (non-studded) / in (.7 mm) diameter T8 Linear and U-bent in (5 mm) diameter 7 W [4 in (60 mm)] 5 W [36 in (94 mm)] 3 W [48 in (9 mm)] 0.58 W-T43-0--S (studded) W-T43-0- (non-studded) 0.40 W-T W-T85-0- W-T85-0- W-T83-0 W-T83-0 SPTON SUMTTL Page 3
4 ase imensions c Threaded Stud 0.9 in (7.4 mm) 4.0 in (07 mm).00 in (5 mm) 3.00 in (76 mm) 4.90 in (4 mm) 4.60 in (7 mm) (mounting centers).00 in (5 mm).08 in (7 mm).60 in (4 mm).39 in (35 mm) 8-3 Threaded Stud 0.9 in (7.4 mm) 6.00 in (5 mm).00 in (5 mm) 3.00 in (76 mm) 6.75 in (7 mm) 6.50 in (65 mm) (mounting centers).00 in (5 mm).00 in (5 mm).60 in (4 mm).39 in (35 mm) 6. in (409 mm).00 in (5 mm).8 in (30 mm) 8.00 in (457 mm) 7.70 in (450 mm) (mounting centers) Mounting studs are provided on models ending in "-S". When ordering, delete the suffix -S in the ballast model number if the mounting studs are not needed. SPTON SUMTTL Page 4
5 Wiring iagrams c One T4 ompact Lamp lack (immed ot) imming ontrol allast lue lue 4-pin Lamp older Two T4 ompact Lamps imming ontrol lack (immed ot) allast lue 4-pin Lamp older 4-pin Lamp older lue imming control wire colors do not necessarily match the ballast wire colors (e.g. control dimmed hot may be red and ballast dimmed hot may be black). Wire colors shown are for Lutron ballasts and controls only. allast and lighting fixture must be effectively grounded. Note: or T4 compact lamps, the maximum lamp-to-ballast wire length is 3 ft ( m). SPTON SUMTTL Page 5
6 Wiring iagrams c One T8 Lamp imming ontrol lack (immed ot) imming allast luorescent Lamp 3 lue lue Two T8 Lamps imming ontrol lack (immed ot) imming allast luorescent Lamp 3 luorescent Lamp 3 imming control wire colors do not necessarily match the ballast wire colors (e.g. control dimmed hot may be red and ballast dimmed hot may be black). Wire colors shown are for Lutron ballasts and controls only. allast and lighting fixture must be effectively grounded. 3 ncludes 6 in (5 mm) T8 U-bent lamps. Note: or T8 lamps, the maximum lamp-to-ballast wire length is 7 ft ( m). SPTON SUMTTL Page 6
7 TTNTON LTRNS N ONTRTORS allast/socket Leads Lead lengths from ballast to socket must not exceed 7 ft ( m) for T8 linear lamps, and 3 ft ( m) for T4 compact lamps. Lamp Sockets Quality lamp sockets are required to ensure positive lamp-pin to socket contact. T8 lamps require knife-edge sockets. U-bent lamps require locking sockets and proper lamp support to hold lamp pins in full contact with the socket. Lamp Mounting Many fluorescent lamp sockets are available with mounting slots to vary the height of the lamp away from the grounded metal surface. aving a fluorescent lamp too close to the grounded metal will reduce lamp life. aving a fluorescent lamp too far away from the grounded metal will make the lamp flicker or not turn on at all. Please note that all of the lamp heights are measured between the grounded metal surface and the glass wall of the lamp. Lamp Mounting height allast Mounting for T4 Lamps Lamp Socket (side view) rounded metal MPORTNT: Lamps must never touch ground plane and should be placed without obstruction. o not allow lamp glass to come in direct contact with any grounded metal surface. Mounting for T8 Lamps Mount lamps /8 to 3/4 in (3. to 9 mm) away from the grounded metal surface. allast Operating Temperature allast case temperature must not exceed 67 (75 ) at any point on ballast c old ir low nsure that no cold air (from V system, etc) is blowing across the lamps. ooling the lamp will cause performance issues as noted in NM LS-34. Wiring and rounding ll wiring from the dimming control to the ballasts is line voltage wiring and may be run together in the same conduit. allast and lighting fixture must be effectively grounded. allasts must be installed per national and local electrical codes. Number of allasts per ontrol calculate the maximum number of ballasts allowed per control, divide control s current capacity by individual ballast current. ertain controls allow a specific maximum number of ballasts. TTNTON LTS MNRS PRORMN Lamps Seasoning Requirements Some fluorescent lamp manufacturers recommend that new fluorescent lamps be operated at full output ( seasoned ) before they can be dimmed, to render lamp impurities inert, ensuring proper dimming performance and average rated lamp life. Please contact your lamp manufacturer for seasoning requirements. SRV Replacement Parts Use replacement parts with exact Lutron model numbers. onsult Lutron if you have any questions. urther nformation or further information, please visit us at or contact our 4-hour Technical Support enter at SPTON SUMTTL Page 7
Hi-lume Overview. EcoSystem Hi-lume 1% Architectural Dimming
cosystem Hi-lume % rchitectural imming Hi-lume Overview 369-398c 06.04. Hi-lume architectural electronic dimming ballasts are designed to meet the most demanding lighting requirements. y providing industry
More informationCompact SE Overview. High-Performance Dimming. Ballast
allast Compact SE Overview CompactSE- 03.08.04 or designs requiring the energy savings and aesthetic appeal of dimmed T4 compact fluorescent or T5 twin-tube lamps, Compact SE dimming ballasts are your
More informationCompact SE Overview. High-Performance Dimming. Ballast
Compact SE Overview CompactSE 01.10.10 For designs requiring the energy savings and aesthetic appeal of dimmed T4 compact fluorescent or T5 twin-tube lamps, Compact SE dimming ballasts are your solution.
More informationTVE Overview. Lighting Management Dimming. Fluorescent Dimming Ballasts
TVE Overview Eco-0TM TVETM 0% TVE () 02.9.04 The (Eco-0) TVE is a 0% fluorescent dimming ballast for applications using a 0-0V control. TVE ballasts are also designed to work seamlessly with 0-0V lighting
More informationFDBT S 32W120V DM Bal
3804 South Street 75964-763, TX Nacogdoches Phone: 936-569-794 ax: 936-560-4685 llenwatson@elliottelectric.com DT430S 3W0V DM al Catalog Number Manufacturer Description Weight per unit Product Category
More information3-Wire Control, 220/240 Volt T-8 Linear, T-4 Quad Tube and T-5 Twin Tube Lamps
3-Wire Control, 220/240 Volt T-8 Linear, rev hi-220-240-1b 1.10.02 2.38 w (60mm) x 1.50 h (38mm) x 9.50 l (241mm) HOT DIMMED HOT NEUTRAL Hi-lume Power Control Dimming Ballast Lamps DESCRIPTION Continuous,
More information3-Wire Control, 120, 277 Volt T5 Twin Tube Compact Lamps, T4 Quad Tube and T4 Triple Tube
3-Wire Control, 120, 277 Volt, T4 Quad Tube and T4 Triple Tube rev hi-compact-1a 3.7.01 2.38 w (60mm) x 1.50 h (38mm) x 9.50 l (241mm) T4 - One Lamp 3.00 w (76mm) x 1.00 h (25mm) x4.90 l (124mm) T4 - Two
More informationEcosystem 5 Percent 3-Wire and Ecosystem Digital Link Controlled T4 Compact, 1 Lamp, Ballast Factor Of 0.95, K-Can, Studded, 26/32W
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 EC3DT4MWKU1S 26/32W T4 1LMP Ba Lutron Catalog Number Manufacturer Description Weight per unit Product Category EC3DT4MWKU1S
More informationEcoSystemR Multiple Control Input Ballasts
EcoR Multiple Control s 369454h 1 09.15.14 Digital electronic dimming ballasts maximize the benefits of a lighting management system. EcoR s offer 100% to 10% dimming; ideal for use where saving energy,
More informationEcoSystem Multiple Control Input Ballasts
Eco Five Control Digital Dimming s Eco Multiple Control s 369454l 1 09.02.16 Digital electronic dimming ballasts maximize the benefits of a lighting management system. Eco s offer 100% to 10% dimming;
More information1,2,3... As easy as. Mark 10 Powerline. For Compact Fluorescent Lamps
s easy as 1,2,3... Mark 10 Powerline immable allasts Listed 704G Philips dvance Mark 10 Powerline immable allasts make converting your existing fixtures easy. For companies looking to make their fixed-output
More informationEcoSystem Multiple Control Input Ballasts
Eco Multiple Control s Eco s 1 06.25.10 Digital electronic dimming ballasts maximize the benefi ts of a lighting management system. Eco s offer 100% to 10% dimming; ideal for use where saving energy, increasing
More informationFluorescent ballast and LED driver
Fluorescent ballast and LED driver Selection uide Lutron s and drivers Lutron Table of contents Fluorescent ballast and LED driver selection guide Introduction 2 Scalable light management solutions 4 Understanding
More informationHi-lume LED Overview. LED Dimming Driver Hi-lume LED Architectural Dimming
Hi-lume LED Overview Hi-lume LED 1 12.11.9 Hi-lume LED is a high-performance, constant current driver that provides energy-efficient dimming for LED lighting. With industry-leading full-range % to 1% dimming,
More informationAn energy saver combines energy saving & a compact design
Lighting An energy saver combines energy saving & a compact design Economy Twister ompact Entry Spiral shape energy saving lamp, starts bright light rapidly and fits everywhere. It saves your money due
More informationSuperDim Analog Dimming Technical Product Information
Universal ighting Technologies is a subsidiary of Panasonic ighting Americas, a member of the Panasonic Corporation Eco Solutions Company SuperDim Analog Dimming Technical Product Information SuperDim
More informationSuperDim Analog Dimming
SuperDim Analog Dimming Technical Product Information SuperDim System Features Universal ighting s SuperDim analog ballasts offer the most cost-effective solution for energy-saving requirements. Universal
More informationPlanning Low Voltage Layouts
Outdoor_ransformers_Outdoor_ransformers.qxd 11-11-10 3:40 PM Page 1 1850 Wilson Avenue, oronto, Ontario, anada, M9M 1A1 Ph: 416-741-7336 Fax: 416-741-9104 SEION H OUDOOR H1 OUDOOR Low Voltage ransformers
More informationPhase-Adaptive Power Module
Phase-Adaptive Power Module Provides dimming control for 1 zone of a full 16 A lighting load. May be used to dim incandescent, halogen, electronic low-voltage, magnetic low-voltage, neon/cold cathode.
More informationELECTRONIC FLUORESCENT BALLASTS
Ordering Information How to Order Philips Lighting has developed the industry s broadest distribution system for electronic ballasts. More than 000 stocking distributors nationwide. For information on
More informationJune 2005 CN35 Electrically Held Vol. 2, Ref. No. [0494]
7-2 Lighting ontactors Open ontrol June 2005 N5 lectrically Held Vol. 2, Ref. No. [09] ontents eatures Instructional Leaflets 7 escription Page lectrically Held Product escription....... 7-2 pplication
More informationRELB2S40N35I (2)F40T12 120V Ele BLST
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 RELB2S40N35I (2)F40T12 120V Ele BLST Philips Advance Catalog Number Manufacturer Description Weight per unit Product Category
More informationVEL2S40SC35I 2 F34T12 277V Electronic Ballast
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 VEL2S40SC35I 2 F34T12 277V Electronic Ballast Philips Advance Catalog VEL2S40SC35I Manufacturer Philips Advance Description
More informationVEL2P75S35I 2-F96T12 277V Electronic Ballast
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 VEL2P75S35I 2-F96T12 277V Electronic Ballast Philips Advance Catalog Number VEL2P75S35I Manufacturer Philips Advance Description
More informationLED Driver and Fluorescent Ballast
A history of sustainability, innovation, and quality Sustainability At Lutron, sustainability is not a new concept. Since 96, we have been designing industry-leading technology that saves energy and reduces
More informationEcoSystem Dimming Power Module for 3-wire Lutron Dimming Ballasts. EcoSystem One-Line. EcoSystem C5-BMJ-16A. EcoSystem Dimming Module
Dimming Power Module for 3-wire Lutron Dimming Ballasts The Lutron dimming power module allows integration of Lutron 3-wire phase controlled dimming ballasts into Lutron bus supplies (Eco-10 and Hi-lume
More informationJust light that you can install and forget
Lighting Just light that you can install and forget Economy stick Entry non-covered energy saving lamp, Long life with low energy consumption. Product consists of Philips quality at everyday low price
More informationOpen, NEMA Type 1, 3R, 4/4X and 12. Auxiliary Contacts
0.- Motor Starters & ontactors Low Voltage Lighting ontactors lectrically eld N January 00 Sheet 18 0 1 7 8 0 1 7 8 0 N-Open (L0-nclosed) 0 mpere 0 mpere Product escription Lighting ontactors are designed
More informationELECTRONIC FLUORESCENT BALLASTS
Ordering Information How to Order Philips Lighting has developed the industry s broadest distribution system for electronic ballasts. More than 3000 stocking distributors nationwide. For information on
More informationReduce Maintenance Costs *
Reduce Maintenance Costs * Philips Advance programmed start parallel Optanium ballasts for T8 lamps helps lower maintenance costs with independent lamp operation. Philips Advance Optanium high-efficiency
More information1 Safety instructions. 2 Intended use. 3 Product characteristics. 4 Operation. LB management. Universal touch dimmer insert LED
Art. no.: 1711DE Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible. Please
More informationTable of Contents T8 Instant Start Ballasts
Table of Contents T8 Instant Start Ballasts gelighting.com Ballasts Understanding T8 Fluorescent Ballasts...10-2 Understanding Fluorescent Systems...10-3 Fluorescent Ballast Application Notes...10-5 UltraMax
More informationMorris Products 53 Carey Road, Queensbury, NY 12804
Catalog Number 790 UPC Number 60986790 Description Low Profile Emergency Lighting allast 500 Lumen T5 & T8 Fixtures Features For both normal and emergency Flourescent lighting. In the event of a Power
More informationControls. CONTROLS AND ACCESSORIES PRODUCT FAMILY FEATURES DIMMERS DIMENSIONS SPECIFICATION SERIES STANDARD FEATURES
SPECIFICATION SUBMITTAL s The contractor s choice in rugged, linear slide dimmers. www.lutron.com/nova CONTROLS AND ACCESSORIES Slide-to-Off s Preset s Select light level with slider; slide down to off
More informationLP Dimming Panels. GRAFIK Systems
GAFIK Systems lp-1 12.8.03 are ideal for projects with many small loads. Each panel provides power and dimming for up to 32 dimming legs. Features Work directly with incandescent, magnetic low voltage,
More informationStrip Fixture URS Light Bar Retrofit Installation Instructions Revised:
Strip Fixture URS Light Bar Retrofit Installation Instructions Revised: 20180126 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency
More informationDLTC. lighting controls. transfer circuit for use with low-voltage down-lighting. features
LT transfer circuit for use with low-voltage down-lighting Two channel device providing switching for up to 75 watts per channel ombines existing low-voltage lighting with a 12 volt emergency unit power
More informationPLUG-IN LAMPS SELF BALLASTED LAMPS PLUG-IN LAMPS WITH SEPARABLE ELECTROMAGNETIC ADAPTERS ACCESSORIES MISCELLANEOUS
4705 01 Lamp Shapes FEA/2D 2D FLE Triple iax FLE Quad iax Triple iax Double iax iax FL FLG FLG/E PLUG-IN LAMPS 2D 2-Pin... 5-5 2D 4-Pin... 5-5 Double iax 2-Pin... 5-6 Double iax 4-Pin... 5-7 High Lumen
More informationBallasts For High Intensity Discharge Lamps
allasts For High Intensity Discharge Lamps Universal Means Higher Expectations In High Intensity Discharge Universal Lighting Technologies ( Universal ) offers a wide array of ballasts for High Intensity
More informationUL AND CODE COMPLIANCE
BAL500 FLUORESCENT EMERGENCY BALLAST 500 Lumens APPLICATION The BAL500 fluorescent emergency ballast works in conjunction with the AC ballast to convert new or existing fluorescent fixtures into emergency
More informationEnergy Saver Compact Fluorescents - Going green never looked so good
Lighting Energy Saver ompact luorescents - Going green never looked so good Energy Saver T2 The Philips EnergySaver T2 provides energy efficient lighting in a smaller, sleeker, size that fits more fixtures.
More information1 Safety instructions. 2 Intended use. 3 Product characteristics. 4 Operation. System Universal LED dimming insert Standard
Order no.: 5400 00 Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationLinear Line Voltage LED Engine
Linear Line Voltage LED Engine Product Specification Introduction The TERRALUX Linear LED Engine is a fully integrated, self-contained, plug-and-play LED solution for lighting fixture manufacturers and
More informationDistribution Restriction Statement Approved for public release; distribution is unlimited.
CEMP-ET Engineer Technical Letter 1110-3-441 Department of the Army U.S. Army Corps of Engineers Washington, DC 20314-1000 Engineering and Design ELECTRONIC BALLASTS FOR FLUORESCENT LIGHTING FIXTURES ETL
More informationSkylark C L Dimmer. Skylark. Wallbox Controls. Dimmer for CFL and LED dimmable bulbs.
Skylark C L for CFL and LED dimmable bulbs. C L 369684a 08.0.2 Features On / off rocker switch with a linear-slide dimmer for a standard designer wallplate opening HEDT Technology: Lutron s advanced dimming
More informationWALL LO-OUTPUT. Project. Type. Notes
Project Type Notes PERFORMANCE/LINEAR FT AT 3000K AND 3500K NOMINAL LUMEN OUTPUT INPUT WATTS* EFFICACY* 3 9/16 300 lm/ft 2.9 W/ft 104 lm/w 400 lm/ft 3.9 W/ft 102 lm/w 500 lm/ft 5.0 W/ft 100 lm/w 1 5/8"
More informationICN3P32SC35I 3-F32T8 120/277V Electronic Ballast
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 ICN3P32SC35I 3-F32T8 120/277V Electronic Philips Advance Manufacturer Description Weight per unit Product Category Features
More informationUniversal Retrofit System Installation Instructions Revised:
Universal Retrofit System Installation Instructions Revised: 20150624 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency to
More informationELECTRONIC FLUORESCENT BALLASTS
ELECTRONIC FLUORESCENT LLSTS Fluorescent allasts Optanium mbistar SmartMate Standard T5HO PureVOLT 1 ELECTRONIC FLUORESCENT LLSTS Fluorescent allasts Fluorescent allasts - - Optanium High-efficiency electronic
More information1992 Energy Policy Act A Pacific Energy Center Factsheet
1992 Energy Policy Act A Pacific Energy Center Factsheet The Energy Policy Act of 1992 affected all users of electric lighting. In addition to instituting requirements for electric motors, utility distribution
More informationBALT5-800 LOW-PROFILE FLUORESCENT EMERGENCY BALLAST
BALT5-800 LOW-PROFILE FLUORESCENT EMERGENCY BALLAST APPLICATION The BALT5-800 low-profile fluorescent emergency ballast works in conjunction with the AC ballast to convert new or existing fluorescent fixtures
More information28.1. NEMA Contactors and Starters. Contents. Contactors Non-Reversing and Reversing. Freedom Series. Product Description
.1 NM ontactors and Starters Non- and ontactors ontactors Non- and Product escription Non- ontactors are most commonly used to switch motor loads in applications where running overcurrent protection is
More informationEnergy Solutions LED Accelerator Program
Energy Solutions LED Accelerator Program Product Qualification Statement I hereby certify that the LED lighting product (Product) listed below meets all applicable general and specific criteria for qualification
More informationBAL3000 FLUORESCENT EMERGENCY BALLAST Specification-grade: Up to 3500 lumens One or two-lamp emergency illumination
BAL3000 FLUORESCENT EMERGENCY BALLAST Specification-grade: Up to 3500 lumens One or two-lamp emergency illumination APPLICATION The BAL3000 fluorescent emergency ballast works in conjunction with an AC
More informationProduct Description TORNADO. Benefits. Features. Application
Lighting Product escription TORNAO The Helix range is a twist-shape compact fluorescent lamp, with optimal light distribution.it is available in 11W, 15W, 20W and 23W (25W), with lumen equivalence of 60W,
More informationHIGH FREQUENCY ELECTRONIC BALLASTS
HIGH FREQUENCY S Introduction High efficiency, high frequency electronic ballasts offer enhanced lighting performance and energy savings. The Electric Research Institute estimates that lighting consumes
More informationT5 versus T8 Fluorescent Lamps. The good, the bad, & the ugly about T8 and T5 lamps
T5 versus T8 Fluorescent Lamps The good, the bad, & the ugly about T8 and T5 lamps Association of Energy Engineers- Cleveland Chapter Tuesday, February 22, 2005 Presented by: Lewis S. Sternberg, LC Consultants
More informationELECTRONIC HID BALLASTS
Overview Just as electronic ballast technology enhanced fluorescent lighting systems, electronic HID ballasts bring significant performance improvements to HID lighting systems: Higher efficiency Greater
More informationHigh performance for high ceilings
High performance for high ceilings Philips Advance Optanium programmed start parallel ballasts for T5HO and T8 lamps offers improved efficiency-saving on both energy and maintenance costs. Our new addition
More informationELECTRONIC FLUORESCENT BALLASTS
ELECTRONIC FLUORESCENT LLSTS Fluorescent allasts Optanium mbistar SmartMate Standard T5HO PureVOLT 1 ELECTRONIC FLUORESCENT LLSTS Fluorescent allasts Fluorescent allasts - - Optanium High-efficiency electronic
More informationQO and QOU Miniature Circuit Breakers QOU Miniature Circuit Breakers
QO and Miniature ircuit reakers Miniature ircuit reakers lass 720 / Refer to atalog 0730T9801 Low mpere Miniature ircuit reakers unit mount miniature circuit breakers (cable-in/cable-out) are ideal for
More informationIZT2S32SC 2 Lamp 32/T8 Dimmable Ballast
IZT2S32SC 2 Lamp 32/T8 immable Ballast Philips Advance Catalog Number Manufacturer escription Weight per unit Product Category IZT2S32SC Philips Advance Electronic Ballast, High Frequency; Programmed Start;
More informationALD Dimmer Enclosures
ALD Enclosures FEATURES Attractive crinkle black finish. er Connection Power Supply Neutral Taps Modules (not included) Cooling Fans Dimming Electronics (not included) Available in 2 sizes: ALD6 (6 dimmer
More informationProduct Description TORNADO. Benefits. Features. Application
Lighting Product escription TORNAO The Helix range is a twist-shape compact fluorescent lamp, with optimal light distribution.it is available in 11W, 15W, 20W and 23W (25W), with lumen equivalence of 60W,
More informationBUYERS GUIDE FOR TYPE C DRIVERS. Programmable vs. Field Adjustable LED Drivers
BUYERS GUIDE FOR TYPE C DRIVERS Programmable vs. Field Adjustable LED Drivers Published: January, 2018 What are the different TLED system types? There are three basic types of linear LED tube systems.
More informationICN2S40N35I Ele Ballast (2) F40T V
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 ICN2S40N35I Ele Ballast (2) F40T12 120-277V Philips Advance Catalog Number Manufacturer Description Weight per unit Product
More informationOptanium. High Efficiency IntelliVolt Instant Start Ballasts for High Efficiency T8 Lamps DESIGN HIGHLIGHTS: APPLICATIONS:
Optanium High Efficiency IntelliVolt Instant Start Ballasts for High Efficiency T8 Lamps P R O D U C T O V E R V I E W : Advance expands a new family of Smart Solutions for T8 lighting systems Optanium.
More informationIVR15-SPI Solid State Illuminated Rail 2 Post Integral Power Supply
IVR15-SPI - 1.5 Solid State Illuminated Rail 2 Post Integral Power Supply 1.50 recognized 0.3 90 PERTURE Ends of Illuminated rail field cuttable to a minimum of 2 1/8 in length. Illuminated rail is available
More informationPhase-Adaptive Power Module
GAFIK Eye papm-1 3.12.08 Description Provides capability for a zone on a GAFIK Eye control unit (or other product) to dim a fully loaded circuit of lighting. May be used to control incandescent, electronic
More informationULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS
Ultra Performance LED Tube Installation Instructions Page 1 of 7 ULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS These instructions do not purport to cover all details or variations in components
More informationMaestro Wireless Dimmers and Switches
Maestro Wireless Dimmers and The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings,
More informationAgency Air-Inert Gas Water. Approx. Shipping Weight (lbs.) 1/2 5/ P Brass. Const.
NXT NRATON lectronically nhanced Solenoid Valves rass and odies 1/" - 2" NPT 2/2 3/2 /2 eatures ncrease in pressure ratings to A levels on all products (up to a 500% improvement) Lower power operation
More informationInput Current (Amps) Input Power (ANSI Watts)
ICF-2S42-M2-BS@120 Lamp Type Num. of Lamps Rated Lamp Watts Min. Start Temp ( F/C) Input Current (Amps) Input Power (ANSI Watts) Ballast MAX THD % Power MAX Lamp Current Crest * CFQ26W/G24Q 2 26 0/-18
More informationPhase-Adaptive Power Module with 3-Wire Fluorescent Input
369-358c 1 03.19.12 Description When connected to a 20 A circuit breaker, provides capacity on a 3-wire fluorescent dimmer for a full 16 A load of lighting. May be used to dim incandescent, halogen, electronic
More informationVIA 2 PLUS RECESSED W W W. L U M E N W E R X. C O M
VIA 2 PLUS RECESSED W W W. L U M E N W E R X. C O M DESCRIPTION Via 2 PLUS combines the elegance of Via 2 with the added architectural element of a lens which protrudes ½" below the surface plane. Via
More informationOmega Series Controls HUNT Simplicity Architectural Full Range Fluorescent Dimmers for use with Electromagnetic Fluorescent Lighting 120V and 277V
aáããáåö= Omega Series ontrols UN Simplicity rchitectural Full Range Fluorescent Dimmers for use with lectromagnetic Fluorescent ighting 120V and 277V unt ontrol Systems nc. Fort ollins O 80524 el: (970)
More informationFluorescent Dimming Systems Technical Guide
Fluorescent Dimming Systems Technical Guide Innovation and quality from the world leader in lighting controls Lutron invented the world s first electronic dimming ballast over 30 years ago. Lutron continues
More informationBAL1400 FLUORESCENT EMERGENCY BALLAST Specification-grade One or two-lamp emergency illumination
BAL1400 FLUORESCENT EMERGENCY BALLAST Specification-grade One or two-lamp emergency illumination APPLICATION The BAL1400 fluorescent emergency ballast works in conjunction with the AC ballast to convert
More informationL ale. 4' 8" Fluorescent Two Lamp Decorative Pendant 56 in long, 42 W, Compact Fluorescent, Direct/Indirect Cable Suspension Models APPLICATIONS
11 3 4 in (98 mm) Bottom View (Canopy) H A B C 367-5c 1 07.13.16 18 in 60 in (457 mm 154mm) 1/4 in (6 mm) 4 3 8 in (111 mm) 5 1 in (140 mm) A - Aluminium coverplate B -Aluminium canopy C - i-wire, power,
More informationUser Manual JS-ICON. 624 ARCH Dimmer Rack. JOHNSON SYSTEMS INC. Spring
User Manual JS-ICON 624 ARCH Dimmer Rack JOHNSON SYSTEMS INC. Spring 2007 2002161 Table of Contents JS-ICON 624 DMX JS-ICON 624 CC 6-2.4kW Dimming Strip JS-ICON 624 ND 6-2.4kW Relay Strip Introduction...3
More informationInput Power (Watts) (min/max)
IZT-2T42-M5-BS@120 Lamp Type Num. of Lamps Rated Lamp Watts M Start Temp ( F/C) Input Current (Amps) Input Power (Watts) Ballast Factor MAX THD % Power Factor Lamp Current Crest Factor CFTR32W/GX24Q 2
More informationLinear Line Voltage LED Engine
Linear Line Voltage LED Engine Product Specification Introduction The TERRALUX Linear LED Engine is a fully integrated, self-contained, plug-and-play LED solution for lighting fixture manufacturers and
More information800 TO 2800 LUMEN 4 LED CYLINDER HYPERBOLIC/PARABOLIC/WALLWASH OPEN APERTURE
ENVIRONMENTALLY FRIENDLY, ENERGY EFFIIENT Lumen packages suitable for ceiling heights ranging from 8 to over 35 Efficacies up to 111 lm/w Superior-quality white LED light output using hip on oard technology
More informationBAL3000 BAL3000. Fluorescent Emergency Ballast Lumens. Specification Sheet. Emergency Ballast 1/19/2012. Project: Catalog#: Approved by:
1/19/2012 Fluorescent 1450-3000 Lumens Works in conjunction with an AC ballast to convert new or existing fluorescent fixtures into unobtrusive emergency lighting Maintains illumination of one or two lamps
More informationEnergy Saver Compact Fluorescents - Going green never looked so good
Lighting Energy Saver ompact luorescents - Going green never looked so good Energy Saver Outdoor Looking for an energy saver that does not look like one? The Philips EnergySaver Outdoor family provides
More informationSECTION ELECTRICAL DESIGN AND CONSTRUCTION STANDARDS _ February A. Use heavy duty type fused and non-fused, enclosed switches only.
26 20 00 LOW VOLTAGE PART 1: PRODUCTS 1.01 Wiring Devices A. Electrical Requirements 1.02 Disconnect Switches 1. Minimum 20 ampere rated switches shall be used for lighting and power loads. In cases where
More informationMaestro Wireless Dimmers
Maestro Wireless s Maestro Wireless dimmers function much like standard dimmers, but can be controlled from PicoTM wireless controls and Lutron Radio Powr SavrTM senss. Local lighting controls are useful
More informationELECTRONIC FLUORESCENT BALLASTS
ELECTRONIC FLUORESCENT ALLASTS Fluorescent allasts AmbiStar SmartMate Standard T5HO PureVOLT 1 Lighting s Atlas -11 ELECTRONIC FLUORESCENT ALLASTS Fluorescent allasts Fluorescent allasts - - High-efficiency
More informationEDB-EPD, EGB-EPD and EJB-EPD (Equipment Protection Device) Circuit Breakers for Ground Fault Protection in NF Panelboards
-P, -P and J-P (quipment Protection evice) ircuit reakers for round ault Protection in N Panelboards Square -P, -P and J-P (quipment Protection evice) ircuit reakers are 1-pole thermal-magnetic circuit
More informationInstallation & User Instructions
Installation & User Instructions 16/25A Digital Dimmer (416/425) INTRODUCTION The 416 and 425 are Digital Dimmers capable of dimming a single channel with total loads of up to 16A and 25A respectively.
More informationGP Dimming Panels 230 Volt (CE)
GAFIK Systems 30 Volt (CE) gp- 03.0.04 GP3/4 Mini Panels GP8-4 Standard-Size Panels provide power and dimming for up to 4 load circuits and control any light source, including full-conduction non-dim.
More informationCOMPACT FLUORESCENT. 83 Mini-Lynx Sticks. 86 Mini-Lynx Spirals. 88 Power-Lynx. 89 Mini-Lynx Classico. 90 Mini-Lynx Compact GLS
83 Mini-Lynx Sticks 86 Mini-Lynx Spirals 88 Power-Lynx 89 Mini-Lynx Classico 90 Mini-Lynx Compact GLS 91 Mini-Lynx Compact Ball 92 Mini-Lynx Candle 93 Mini-Lynx Globe 94 Mini-Lynx Reflectors 96 Mini-Lynx
More informationLED 2/3/4ft T8 Tube 120V
E-T8-1200-YR LED 2/3/4ft T8 Tube 120 Our LED Tubes utilize the latest LED chips as the light source, whilst using the standard T8 end caps, which makes it easy to install and replace traditional fluorescent
More informationOutdoor Installation Using an Electronic LED Power Supply (TE-60L-12)
0 Edge Lighting. All Rights Reserved. 78 W. Fullerton Ave Chicago, IL 606 Tel: 77-770-9 Fax: 77-9-6 www.edgelighting.com info@edgelighting.com Installation Instructions for Port Round & Square LED PORT-RD-ST-SA
More informationFLUORESCENT LAMPS FEATURES & BENEFITS ULTRA 8 LINEAR AND U-BEND LAMPS FOR GENERAL LIGHTING
Form No. S-UFLT8/UB/R-913 FLUORESCENT LAMPS ULTRA 8 LINEAR AND U-BEND SERIES ULTRA 8 LINEAR AND U-BEND LAMPS FOR GENERAL LIGHTING USHIO proudly carries a line of fluorescent lamps that include: Extended
More informationNumber 9 January SECTION 1 Dimming of T12 Fluorescent lamps 2. SECTION 2 Dimming of T8 Fluorescent lamps 4. SECTION 3 Do's and Don'ts 6
FACT sheet Number 9 January 1993 A GUIDE TO FLUORESCENT DIMMING E nsuring good quality fluorescent dimming calls for more than simply using a 'fluorescent' type of dimmer. Many other factors need consideration,
More informationEfficor* Intro. Conformity to standards. Ambient conditions. Climatic resistance (IEC 68-2) Approvals/Marking. Mounting positions
fficor* onformity to standards /N 60947-1 04 /N 60947-4-1 UL508 /N 60947-5-1 UL486 /N 60947-5-4 S22- N500 N 16 101/102 N50012 N50005 pprovals/marking mbient conditions Storage temperature -55º to +80º
More informationHow to Order 1 T Z A. r Pressure range. 05 Pressure range 0 to 0.5 MPa 10 Pressure range 0 to 1 MPa 16 Pressure range 0 to 1.6 MPa
oolant Valve Series S External pilot solenoid S ir operated S How to Order 0 0 Y 0 0 T Z q w e r t y u i o!0!!!!! q Series S00 S00 S00 w Valve type ormally closed ormally open e Seal material R FKM r Pressure
More informationGP Dimming Panels 230 Volt (CE)
30 Volt (CE).3.08 GP3/4 Mini Panels GP8-4 Standard-Size Panels provide power and dimming for up to 4 load circuits and control any light source, including full-conduction non-dim. Models available with:
More informationLinear Replacement Lamps
Linear Replacement Lamps PLEASE NOTE: DLC DEFINES ALL TUBE-STYLE LED PRODUCTS THAT USE THE LAMP HOLDERS (I.E. SOCKETS OR TOMBSTONES ) IN THE LUMINAIRE TO MECHANICALLY OR ELECTRICALLY CONNECT TO THE FIXTURE
More information