Model VKFD28 Flexible Sprinkler Drops (LPCB Approved) Installation Manual. January 2016 Form No. F_ Rev 16.1

Size: px

Start display at page:

Download "Model VKFD28 Flexible Sprinkler Drops (LPCB Approved) Installation Manual. January 2016 Form No. F_ Rev 16.1"

Ethan Black
6 years ago
Views:

1 Model VKFD28 Flexible Sprinkler Drops (LPCB Approved) Installation Manual January 2016

2 Page 2 of 10 TABLE OF CONTENTS Section Description Page 1 Benefits 3 2 Installation Instructions 3 3 Technical Data 7 4 Part Numbers 8 5 Components 9

Page 3 of 10 Figure 1: Model VKFD28B Braided Flexible Drop (Shown with a Viking Concealed Sprinkler) Figure 2: Model VKFDU28 Unbraided Flexible Drop (Shown with a Viking Concealed Sprinkler) 1.

3 Page 3 of 10 Figure 1: Model VKFD28B Braided Flexible Drop (Shown with a Viking Concealed Sprinkler) Figure 2: Model VKFDU28 Unbraided Flexible Drop (Shown with a Viking Concealed Sprinkler) 1. benefits Viking Flexible Sprinkler Drops provide many benefits for installation or retrofit compared to fixed including: More efficient use of manpower Improved performance and installation quality Precise location of sprinklers Flexible installation for Seismic applications Corrosion-resistant materials Fewer tools required for installation 100% Factory Tested Special centre bracket design that allows all sprinkler types, including concealed, to be installed as the last step, increasing flexibility Meets NFPA, EN, CNBOP, R1, and LPC guidelines Approved for use with suspended ceilings with intermediate- and heavy-duty systems designed per ASTM C635 and C636 Viking Flexible Sprinkler Drops are a complete unit assembly. Included parts: Braided or non-braided exterior, corrugated, stainless steel flexible hose Ø28 mm Inlet nipple 1 (DN25) or 1-1/4 (DN32) NPT or BSPT Straight outlet reducer 1/2 (15 mm) or 3/4 (20 mm) for attachment of sprinkler (90 angle outlet reducer available for order separately) Support bar Brackets Viking Flexible Sprinkler Drops are available in various lengths to minimize the number of installed bends and meet the minimum material requirements of the installation. 2. INSTALLATION INSTRUCTIONS Step 1: Ensure proper sprinkler position where the sprinkler is to be located and cut the proper clearance hole in the ceiling tile as described in the sprinkler technical data page. The sprinkler should be installed near the centre of the ceiling tile and between the main support rails of the suspended ceiling support system. The standard centerline of support beams is 600 mm, of which the support bar (Item 2 in Figure 1 furnished as standard) is 650 mm long. Form No. F_ Rev 16.1

Page 4 of 10 NOTE: A 1200 mm spacing is possible with a separately available support bar 1250 mm long (Part No. 14398).

4 Page 4 of 10 NOTE: A 1200 mm spacing is possible with a separately available support bar 1250 mm long (Part No ). Step 2: See Figure 3 Attach the rail clips (1) to the ceiling grid using a screwdriver or by hand. REF# PART # DESCRIPTIONS QTY RAIL CLIP 2 2** RECTANGULAR BAR, 650 mm WING BOLT, M6 X 15 mm WING BOLT, M6 X 25 mm OUTLET REDUCER SUPPORT BRACKET 1 NOTE: When installing, attach the brackets to the ceiling s main tee bar supports. Do not attach to cross support rail members. ** For long bar 1250 mm, order Part No kit separately (10 bars per kit) Figure 3: VKFD Rail Clip Installation Step 3: See Figure 4 A. Apply a non-hardening thread sealant or sealant tape to the male threads of the nipple ONLY on the end that installs into the tee or elbow. DO NOT apply sealant to the hose connection thread. B. Install the inlet nipple into the branch line outlet tee or elbow. Make sure the tapered pipe thread is installed in the tee and the special shoulder thread is pointing towards the sprinkler location. Tighten the nipple into the tee with a pipe wrench for a leak-tight connection. C. Hand-tighten the hose on the fitting, then use a wrench to tighten and additional 1/4 turn (~8.5 N.m). The Viking flexible sprinkler hose includes a slip nut on both ends for attachment to the branch line fitting and the sprinkler outlet fitting that is secured in the ceiling support system as shown in Figure 4. NOTE: If possible, attach the hose after it has been formed into the proper installation shape to eliminate rotation of the hose when threading onto fittings. Figure 4: VKFD Nipple and Hose Installation

5 Page 5 of 10 Step 4: See Figure 5 Ensure that the maximum number of specified bends, with the minimum bend radius, are adhered to. A radius tool is available, which provides a minimum bend radius of 3 (75 mm) (part number 14402). NOTE: To minimize friction loss, a large bend radius is recommended; however it must be a smooth, constant radius. Note that the radius of the flex hose must NOT fall in the non-corrugated ends. Avoid long lengths of hose for the distance, as this would require more bends to install, possibly including low spots or kinks. Excessive numbers of bends might not properly drain and can cause severe pressure loss. Figure 5: VKFD Examples of Proper Installation NOTES: To route flexible hose around obstructions, select the proper length based on the type of obstruction to be avoided. Minimize the number of bends to ensure proper operation. Observe the minimum bend radii and the discharge location from the branch piping. See Figure 5 for illustration of recommended practice. Figures 6 and 7 illustrate different use of fittings. Figure 6 Form No. F_ Rev 16.1 Figure 7

6 Page 6 of 10 Step 5: Install the desired sprinkler head in the outlet reducer. Due to the special design of the Viking centre bracket, the sprinkler can be installed into the outlet nipple before it is attached to the sprinkler hose. Apply non-hardening thread sealant or sealant tape to the male threads of the sprinkler head and tighten the sprinkler in the outlet reducer using the appropriate sprinkler head wrench. Assemble one end of the flexible hose to the reducer shoulder thread and hand tighten, then tighten 1/4 turn to approximately 8.5 N.m of torque so as to not cut or crush the O-ring provided in the hose assembly. Step 6: Properly form the required bend radii around bend tool or cylindrical formed object or pipe, to provide constant and smooth radius, and align the hose for connection to the special inlet nipple installed in the sprinkler system branch line tee. First, attach the hose slip nut onto the shoulder nipple fitting hand tight, plus 1/4 turn to tighten to approximately 8.5 N.m of torque. DO NOT use sealant compound on the shoulder nipple threads. Next, properly form the flexible hose, forming the proper number of bends and minimum bend radius to align with the sprinkler outlet reducer. Attach the slip nut of the flexible hose to the sprinkler outlet reducer hand tight, same as above. DO NOT apply sealant to this thread, as the O-ring makes the seal. Step 7: After checking alignment of the sprinkler with the clearance hole and flush positioning with the finished ceiling surface, verify that all wing screws and the hose slip nuts are secure. The sprinkler outlet reducer and sprinkler can be placed in the centre bracket and the wing screw tightened by hand and/or power driver to a recommended torque of 2 N.m. Test the system for leaks per the hydrostatic test procedure of the applicable edition of NFPA 13, EN12845, or other local installation standard. TABLE 1: FRICTION LOSS DATA WITH 75mm BEND RADIUS (½ or ¾ OUTLET) Hose length (mm) Outlet Equivalent Length** of 1 Schedule 40 pipe (m) Maximum number of 90 bends*** 700 ½ or ¾ ½ or ¾ ½ or ¾ * ½ or ¾ * ½ or ¾ *These lengths are LPCB approved but not authorised by LPC Technical Bulletin TB227. **Equivalent length is for a straight hose with one 90 bend. ***According to LPCB approval. A 90 outlet elbow (if used) is considered one 90 bend.

7 Page 7 of Technical data Specifications: Available since Hose tube diameter: 28 mm outside diameter Lengths available 700mm, 1000 mm, 1200 mm, 1500 mm and 1800 mm Inlet 1 /DN25 or 1-1/4 /DN32 BSPT male pipe Available braided or unbraided Outlet reducer straight with 1/2 /15mm or 3/4 /20mm NPT (suitable for both NPT and BSPT) Outlet reducer 90 angle with 1/2 /15mm or 3/4 /20mm NPT (suitable for both NPT and BSPT) Corrugated tube is polished and boron treated and annealed after forming to insure relief of all material stresses and removal of all scale Maximum Working Pressure (unbraided) = 13.8 bar Maximum Working Pressure (braided) = 17.2 bar! WARNING Refer to the sprinkler technical data page, as the temperature rating and maximum pressure rating of the sprinkler may be different than the Flexible Sprinkler Drop. Test Pressure (unbraided) = 20.7 bar Test Pressure (braided) = 25.8 bar Accepted for wet and dry systems as noted in NFPA 13 LPCB Approved for wet systems in accordance with LPC Technical Bulletin TB227 Maximum ambient temperature: 149 C EPDM seal Minimum bend radius: 75 mm for LPCB Approval Material Standards: Flexible Tube: Outlet Reducer (Straight or Angled): Inlet Nipple: Seal: Slip Nut: Support Brackets (all): Support Bar: AISI 304 Stainless Steel SPPS Steel with yellow zinc plating SPPS Steel with yellow zinc plating EPDM SS41 Steel with zinc plating SS41 Steel with zinc plating SS41 Steel with zinc plating TABLE 2: BOX CONTENTS Each box of VKFD28 Flexible Hoses contains ten (10) complete assemblies consisting of the parts in this table. Description Quantity Flexible hose 10 Inlet nipple 10 Outlet reducer (straight) 10 Support bar 10 Support clip 20 Centre bracket 10 Wing bolt, M6 x 15mm 30 Wing bolt, M6 x 20mm 20

8 Page 8 of part numbers Part Number (Unbraided) TABLE 3: PART NUMBERS Part Number (Braided) Length (mm) Inlet Outlet VKFD28U-111 VKFD28B mm BSP 15mm/1/2 VKFD28U-211 VKFD28B mm BSP 15mm/1/2 VKFD28U-311 VKFD28B mm BSP 15mm/1/2 VKFD28U-411 VKFD28B mm BSP 15mm/1/2 VKFD28U-511 VKFD28B mm BSP 15mm/1/2 VKFD28U-112 VKFD28B mm BSP 20mm/3/4 VKFD28U-212 VKFD28B mm BSP 20mm/3/4 VKFD28U-312 VKFD28B mm BSP 20mm/3/4 VKFD28U-412 VKFD28B mm BSP 20mm/3/4 VKFD28U-512 VKFD28B mm BSP 20mm/3/4 VKFD28U-121 VKFD28B mm BSP 15mm/1/2 VKFD28U-221 VKFD28B mm BSP 15mm/1/2 VKFD28U-321 VKFD28B mm BSP 15mm/1/2 VKFD28U-421 VKFD28B mm BSP 15mm/1/2 VKFD28U-521 VKFD28B mm BSP 15mm/1/2 VKFD28U-122 VKFD28B mm BSP 20mm/3/4 VKFD28U-222 VKFD28B mm BSP 20mm/3/4 VKFD28U-322 VKFD28B mm BSP 20mm/3/4 VKFD28U-422 VKFD28B mm BSP 20mm/3/4 VKFD28U-522 VKFD28B mm BSP 20mm/3/4 TABLE 4: PARTS AVAILABLE TO ORDER SEPARATELY Part Number Description mm (3 ) bend radius gauge tool mm (3 ) bend radius clip Inlet Nipple, DN25/1" BSPT Inlet Nipple, DN32/1-1/4" BSPT ½ straight outlet reducer ¾ straight outlet reducer ½ 90 outlet fitting ¾ 90 outlet fitting Support clip Centre bracket mm support bar mm support bar (for larger tile spacing) Wing bolt, M6 x 15mm Wing bolt, M6 x 25mm Plasterboard/drywall clip with screw (2pcs)

Wing bolt, M6 x 15mm Wing bolt, M6 x 20mm 49000703 41200013 41200012

(supplied as standard) Support bar 650mm (available to order separately)

9 Page 9 of components TABLE 5: COMPONENTS Image Description Part Number Support clip Wing bolt, M6 x 15mm Wing bolt, M6 x 20mm Centre bracket Wing bolt, M6 x 15mm Support bar 650mm (supplied as standard) Support bar 650mm (available to order separately) Inlet Nipple, DN25/1 BSPT Inlet Nipple, DN32/1-1/4 BSPT ½ straight outlet reducer ¾ straight outlet reducer

10 Page 10 of 10 ½ 90 outlet reducer ¾ 90 outlet reducer Wing bolt, M6 x 15mm Wing bolt, M6 x 20mm mm (3 ) bend radius gauge tool 14402

Data Sheet 3.11 Issue F

Data Sheet 3.11 Issue F General Description Rapidrop flexible sprinkler hoses are typically used as an alternative to traditional hard pipe arm overs and are particularly suited for use in suspended ceiling applications. The