1 ABOUT THE COMPANY. DoorHan Company Group. kadan. suzhou

Transcription

1 Table of contents About the company 3 Automatic systems for sectional doors 7 Automatic systems for residential sectional doors 8 Automatic systems for residential and industrial sectional doors 12 Automatic systems for industrial sectional doors 20 Automatic systems for gates 31 Automatic systems for sliding gates 32 Automatic systems for swing gates 38 Barriers 45 Rolling shutters, screens and awning automatics 51 All types of automatics accessories 67 Automatic systems accessories 69 Rolling systems automatics accessories 74 Certificates 81 Owned production and warehouse network 85

2

3 ABOUT THE COMPANY

4 1 ABOUT THE COMPANY DoorHan Company Group kadan suzhou DoorHan Company Group Factories is the largest international manufacturer of all automatic gates and rolling systems. Using modern high-technology equipment, we produce operators for all types of doors and rolling shutters automation. We offer operators for residential and industrial sectional doors, sliding and swing gates, rolling shutters, steel rolling doors and barriers. DoorHan Company also supplies the wide range of control devices, safety devices and some additional accessories for all types of the motors supplied. Those devices guarantee maximum safety and service convenience. DoorHan takes into consideration an experience of European manufacturers and develops automation which is suited to hard working conditions (such as unstable voltage, seasonal temperature fluctuations etc.). All devices pass through a full range of tests and the obligatory certification. Line of operators and accessories under the trademark DoorHan meets all the requirements of the clients. An automatics DoorHan quality control is provided by the multi-stage test, which guarantees the long working life and high performance. System approach allows the satisfaction of all the comprehensive gates and rolling systems automation requests of our clients, and provide a professional mounting and after-sales service. 4

5 ABOUT THE COMPANY 1 Continious perfection of the production allows DoorHan Company Group Factories to hold leading positions on the market and offer its clients multi-purpose automatics, which can be combined with to all types of the products, manufactured by our company. We are sure, that this catalogue will help you to choose the automatics just for your needs. 5

6

7 AUTOMATic SYSTEMS FOR GATES AND DOORS

8 2 Automatic systems for residential and industrial sectional doors garage door operators for residential use Garage door operators Sectional-750 and Sectional-1200 Garage door operator Sectional-750 is for residential use. Operator is fixed on the ceiling and opens the door by means of a chain drive. This is designed for the doors up to 2800 mm high with an area of up to 10 m 2. Garage door operator Sectional-1200 is for residential and industrial use. Operator is fixed on the ceiling and opens the door by means of a chain drive. This is designed for the doors up to 3800 mm high with an area of up to 16 m 2. Operators` bodies have the up-to-date ergonomic design. Operators can be easily mounted on the rail and fixed on the ceiling. Built-in lamp for courtesy light is automatically activated when using operators. The opening and closing stop points are determined by the encorder and controlled by the chain reference point. To ensure the maximum safety operation, the control unit is provided with the current protection system. Self-locking non-reversing gearmotor prevents from any unauthorized garage door opening. Accessible emergency release system is provided for power cut situations. Automatic closing function with programmable pause time. Rolling code of transmitters for maximum protection from any unauthorized using. Audio alarm function in case the door stays open for more than 10 minutes. Power consumption less than 8 Watts in standby mode. Smooth start-up and deceleration functions ensures the minimum loads to the system units, thus extending the door and the actuator service life. Door fitting bracket ensures safe fixing procedures upon two planes. 8

9 Automatic systems for residential and industrial sectional doors 2 Special DoorHan logo cover plate to prevent any unauthorized access to the operator display and pushbuttons Wireless radio button to control the operator Built-in long-life courtesy light Digital display to control the adjustments and the operator`s work Operator to the guide 900 space saving mounting possibility. Automatic chain tightener system does mot require any additional regulation. Control unit is suitable to use with unstable power supply Steel drive pinion ensures reliable and long service life Easily removable housing cover High-powered transformator Technical specifications Model SE-750 Kit FA-750 Kit SE-1200 Kit Power supply 230 V, 50 Hz Maximum absorbed power 150 W 150 W 300 W Thrust force 750 N 750 N 1200 N Door speed 0,1 m/sec 0,1-0,18 m/sec 0,1 m/sec Protection class IP 20 Use frequency Continuous Operating ambient temperature C Aperture height Up to 2800 mm Up to 2800 mm Up to 3800 mm Maximum door surface area 10 m 2 10 m 2 16 m 2 9

10 2 Automatic systems for residential and industrial sectional doors Advantages ENCLOSURE Operator can be easily mounted on the rail and fixed on the ceiling. Built-in lamp for courtesy light is automatically activated when using operator. COMFORT AND COST-EFFICIENCY The package includes a radio key-button which can substitute a normal fixed switch and can be used as well as a transmitter. No extra devices are needed for the radio key-button to be used. The SE-750 actuator is remarkable for its low energy consumption. When in stand-by mode and the garage lighting switched off, the total power consumption is 8 W. RELIABILITY, DURABILITY, USABILITY The electromechanical operator is provided with the smooth start-up and deceleration functions, thus excluding any dynamic loads on the system units when starting and stopping the operator and extending its service life. The operator has a low noise level and high performance indicators. EASY TO ADJUST The operator is programmable with the relevant push-buttons and a special display unit reporting various operation performance values. To put the operator in operation, only two parameters should be adjusted: upper and lower positions, then the door opening force should be automatically set. All the controls are available on the enclosure, under an ornamental easy to remove cover plate ensuring the controls to be easily accessible. EXTRA DEVICES To ensure the maximum safety operation mode, the relevant DoorHan photocells or optosensors could be connected to the control unit. Besides that, the relevant key-button additional devices, as well as radio code keypad and any kind of transmitters could be used. No extra devices are needed to use the extra devices. RELEASE DEVICE The door leaf is securely fixed when installing the electromechanical operator. Thus the operator functions as a lock, doesn`t permit the doors to be opened manually. In case of power cut, the operator can be easily unblocked while pulling the built-in release device cord. To reset the operator, it is sufficient to pull the cord once again. When it is necessary to unblock the operator from the outside, an external cable release device should be previously installed; this is keyprotected against any unauthorized unblocking. 10

11 Automatic systems for residential and industrial sectional doors 2 Packages 1. Operator 2. Instruction manual 3. Radio control button 4. Curved bar 5. Straight bar 6. Fixing kit 7. Rail Operator description Operator enclosure 2. Courtesy lamp 3. Display 4. Programming push-buttons 5. Ornamental cover Dimensions, mm Rails for Sectional series operators Steel guide with anticorrosive coating, ensuring the ultimate operation reliability. Special stiffening ribs provided, excluding any guide deflection to ensure the exact door leaf positioning. A steel chain is used in the rail to transfer the movement to the door leaf. This allowing to support higher loads. The chain tension unit permitting to easily maintain the chain in operation conditions. Easy rail carriage unblocking using a cord or external cable release. Smooth and silent carriage movement inside the rail. New support with enforced stiffening ribs SK-3300 rail Included in the SE-500KIT operator package Designed for automation of a door leaf with a maximum height of up to 2600 mm Steel profile thickness of 1,8 mm Guide designed solely to be used with the SE-500 operator SK-4600 rail Included in the SE-1200KIT operator package Designed for automation of a door leaf with a maximum height of up to 3800 mm Reinforced steel profile thickness of 2 mm SK-3600 rail Included in the SE-750KIT operator package Designed for automation of a door leaf with a maximum height of up to 2800 mm Steel profile thickness of 1,8 mm 11

12 Automatic systems for residential 2 Автоматика для and сдвижных industrial ворот sectional doors Garage door operator for residential use Garage door operator Sectional-500 Garage door operator Sectional-500 is for residential use. Operator is fixed on the ceiling and opens the door by means of a chain drive. This is designed for the doors up to 2300 mm high with an area of up to 8 m 2 Operator's body has the up-to-date ergonomic design. Operator can be easily mounted on the rail and fixed on the ceiling. Builtin lamp for courtesy light is automatically activated when using operator. The opening and closing stop points are determined by the encorder and controlled by the chain reference point To ensure the maximum safety operation, the control unit is provided with the current protection system Self-locking non-reversing gearmotor prevents from any unauthorized garage door opening Accessible emergency release system is provided for power cut situations Rolling code of transmitters for maximum protection from any unauthorized using Audio alarm function in case the door stays open for more than 10 minutes Power consumption less than 8 Watts in standby mode Smooth start-up and deceleration functions ensures the minimum loads to the system units, thus extending the door and the actuator service life Automatic closing function with programmable pause time Door fitting bracket ensures safe fixing procedures upon two planes 12

13 Автоматика для Automatic сдвижных systems ворот for residential and industrial sectional doors 2 easy access to programming pushbuttons high-powered transformator built-in long-life courtesy light digital display to control the adjustments and the operator`s work easily removable housing cover automatic chain tightener system does mot require any additional regulation. control unit is suitable to use with unstable power supply steel drive pinion ensures reliable and long service life Technical specifications Model SE-500 Kit Power supply 230 V, 50 Hz Maximum absorbed power 100 W Thrust force 500N Gate speed 0,14 m/sec Protection class IP20 Use frequency continuous Operating ambient temperature from -20 C to +55 C Aperture height 2300 mm Maximum door area 8 m 2² 13

14 2 Автоматика для Automatic сдвижных systems ворот for residential and industrial sectional doors Advantages CLASSICAL DESIGN ENCLOSURE COMBINED WITH THE EASILY RECOGNIZABLE DOORHAN BRAND. Operator can be easily mounted on the rail and fixed on the ceiling. Built-in lamp for courtesy light is automatically activated when using operator. ALL-INCLUSIVE PACKAGE Obstacle detection capability ensured with the movement control function available. Control unit self-diagnostics function identifying and warning about possible fault conditions. RELIABILITY COMES FIRST Low control power (24V) ensuring the required operation safety conditions. Chain rail ensuring high wear resistance. Steel driving pinion ensuring the actuator reliability and long service life. EASY TO ADJUST, EASY TO USE The actuator is programmable with the relevant push-buttons and special display reporting various performance values. To put the actuator in operation, only two parameters should be adjusted: upper and lower positions, then the door opening force should be automatically set. MAXIMUM SAFETY MODE To ensure the maximum safety operation mode, the relevant DoorHan photocells and optosensors could be connected to the control unit. POWERFUL AND COMPACT DESIGN The powerful motor (thrust force of 500N) and compact dimensions optimum balance. FULL PACKAGE READY TO BE USED FOR YOUR DOOR Ideal for residential use. RELEASE DEVICE The door leaf is securely fixed when installing the electrical actuator. Thus the actuator functions as a lock, not permitting the doors to be opened manually. In case of power cut, the actuator could be easily unblocked while pulling the built-in release device cord. The actuator is automatically reset when restarting it (support passing over the carriage). When it is necessary to unblock the actuator from the outside, an external cable release device should be previously installed; this is key-protected against any unauthorized unblocking. 14

15 Автоматика для Automatic сдвижных systems ворот for residential and industrial sectional doors 2 Packages: 1. Operator 2. Instruction manual 3. Curved bar 4. Straight bar (fixed to the guide carriage) 5. Fixing kit 6. Rail Operator description Operator`s enclosure 2. Courtesy lamp 3. Display 4. Programming push-buttons 170 Dimensions, mm Control unit Control unit SE-750 Ключ-кнопка NC NO COM Приемник 433 МГц Sectional-1200 блок управления NC NO 5V DOOR Gnd +24 Gnd +24 Com Out GND IR +12V Двигатель PE 230 В, 50 Гц 15

16 2 Automatic systems for residential and industrial sectional doors Accessories LOCK Reliable protection from a breaking. The rope of the release is galvanized, what ensures its reliability while long-term usage. The emergency release was developed especially for the Doorhan sectional door operators, and it also suits for all manufacturers garage door operators. KEYSWITCH Key-operated push-button KEYSWITCH is used for giving a control command to an operator's control board. A DIP-switch lets to give a control command in the step-by-step mode. There is used one control command for opening, stop and closing. There can be used both NO and NC contacts for connection. In order to give a command you need to turn the key controlling the microswitches contacts; when you release the key, it reverts. KEYPAD Radio code wireless numeric pad KEYPAD is used for remote control of an electronic operator, equipped with an internal or external DoorHan receiver. DHRE-2 External receiver DHRE-2 is meant for other manufacturers automatics control with the help of DoorHan transmitter. It is possible to connect the receiver to any operator, which has normal opened (NO) control contacts. This receiver works on a frequency 433 MHz. The receiver DHRE-2 has two channels, thus it can control one or two operators. Transmitter 4 Remote control transmitters DoorHan are meant for DoorHan automatics or any other device with the DoorHan radio receiver control. You can control one or more (up to 4) different devices (gates, barriers etc.) with the help of one transmitter. OPTOKIT The opto-sensors safety device (OPTOKIT) consists of 2 infrared safety sensors: receiver and transmitter, installed in a special rubber profile (RUBBER) at the bottom of the door panel. The deformation of the rubber profile leads to the interruption of the optical beam and a signal is sent to the control unit. The control unit generates a universally recognized signal, which makes it possible to use an opto-sensor kit with various door automation devices. Photocell Photoelectric detector Photocell is a safety device, consisting of infrared transmitter and receiver, which are installed in a gate opening. If an infrared beam is interrupted, the control board receives the signal of an obstacle in a dangerous area of an automatic system operation, and a system reacts as it was preset by the operation logic stop or reverse of gates. LOCK N The relese is designed ideally for sectional operators. A handle with a key maggot is placed on the gate panel surface. The turning of this handle leads to an easy release of the electric drive, that`s why the gate can be opened manually. 16

17

18 2 Automatic systems for industrial sectional doors Shaft operators for industrial sectional doors SHAFT operators Electromechanically driven SHAFT operators are designed to be used for spring balanced industrial sectional doors. Operators are designed to mount strictly on the shaft. Advanced oil bath technology is used for gearmotors. Operator consists of electric motor, reduction gear and built-in control unit. Electric motor and reduction gear are enclosed in united body. 3-buttons control unit is connected to the control board of the operator. There are 2 ways of installation - with direct transmission on the spring shaft or indirect transmission by chain. Self-blocking reducer enables mechanical blocking of the gate shaft when the operator is stopped. In case of a power cut the door can be moved by using manually activated chain winch. In the event of long-timed power cut the door can be moved manually by activating release device lever. Shaft rated torque of Shaft-30 operator is 30 Nm thus enabling to open the door with an area of up to 18 m 2. It`s ideal both for industrial and residential sectional doors in case there is no possibility to mount a chain operator. Operator is compact and can be easily mounted both to the right and to the left from the door. Shaft-120 is three-phased operator with shaft rated torque 120 Nm. It can be used for a door with an area of up to 40 m 2. simple mounting and adjustment operator goes with all the necessary connections performed there is a possibility to enlarge shaft rated torque by using indirect chain transmission with different transmission ratio long-life manually activated chain winch 3-buttons control unit in package different accessories can be integrated in automatic system automatic closing function with programmable pause time a chain winch can be lengthen in case of high door 18

19 Automatic systems for industrial sectional doors 2 Solid die cast aluminium body Chain winch and release lever Rough and exact adjustment of limit switches caps Built-in control board Operator description Dimensions, mm Reducer body 2. Built-in control board 3. Limit switches block 4. Built-in chain winch 5. Chain (7m - length) 6. Mounting holes 7. Release lever 8. Capacitor 20 µf Shaft series operators technical specifications Model Shaft-30 Shaft-120 Power supply 230 V 380 V Maximum absorbed power 370 W 450 W Shaft rated torque 30 Nm 120 Nm Rotation speed 32 rpm 29 rpm Use frequency 50% 65% Operating ambient temperature Protection class C IP44 Maximum gate area 18 m 2 40 m 2 19

20 2 Automatic systems for industrial sectional doors Advantages High use frequency Operator body is made of sold die cast aluminium. Special cooling ribs enable to raise heat emission thus increasing use frequency. Simple and accessible mounting Due to built-in control unit the operator has compact size and minimum quantity of projected parts. The package includes all the necessary fixing elements. The operator can be easily mounted on the spring shaft and fixed with bracket on the wall. Besides all electrical connections required are performed and all that is needed is to power up the operator and to adjust limit switches. A screwdriver and a spanner from the package help you to make all adjustments. Limit switches Upper and lower end points of a gate are adjusted by limit switches caps. The caps are doubled to provide maximum safety. Every cap has rough and exact adjustment. Additional blue cap enables to integrate external devices in the automatic system. Chain transmission It is also possible to use Shaft operator with indirect transmission by chain with different transmission ratio enabling use even if the lateral space is insufficient or for particularly heavy doors. Shaft rated torque and door maximum area can be enlarged 1.5 times as much. Accessories To ensure the maximum safety operation mode, the relevant DoorHan photocells or optosensors could be connected to the control unit. Besides that, the relevant key-button additional devices, as well as radio code keypad and any kind of transmitters could be used. In this case it is just needed that you connect external radio-receiver. Release system In the event of long term power cut the operator is unblocked by the release lever and the door can be moved manually. Power supply is automatically switched off in this case to provide maximum safety. Chain winch Manually activated chain which enables the door to be moved in case of short term power cut. Quality control 100% DoorHan operators undergo quality control for more than 15 criteria before shipment. 20

21 Automatic systems for industrial sectional doors 2 Package 1. Operator 2. Instruction manual 3. Fixing bracket 4. Chain (8m) 5. Fixing kit 6. 3-buttons control unit with 6m length cable 7. Dowel 8. Screwdriver 9. Spanner 10. Chain coupling Control unit L1 FUSE N SW1 code SW2 DL2 DL3 DL6 DL7 DL5 DL4 6 FSW NC +24Vdc 5-24 Vdc Control unit technical specifications Power supply Motor max. load Absorbed power Accessories max. load Fuse Work time Pause time Terminal board inputs Function logic 230 V 800 W 4 W 0.2 A 6.3 A 250 V Programmable (from 0 to 10 min) Programmable (from 0 to 5 min) Open-Close-Stop-Safety devices-opening and closing limit switches-power supply Automatic/ Stepped semi-automatic/safety/semi-automatic B/ Dead man C/ Mixed B+C 21

22 2 Automatic systems for industrial sectional doors Installations Operator 2. Closing rings 3. Operator fixing bracket 4. Shaft fixing bracket 5. Shaft 6. Big pinion 7. Chain 8. Small pinion Additional chain transmission Transchain 1:1,5 Additional chain transmission enables: to mount the operator below the shaft in case of limited lateral space to enlarge the maximum area of the automatic door 1.5 times as much. Package 1. Z22 pinion assembly with a hub to be mounted on a standard shaft 2. Z22 or Z34 pinion assembly with a hub to be mounted on a standard shaft Transmission chain 1.3m length Shaft segment Dowel 22

23 Automatic systems for industrial sectional doors 2 Accessories BUTTON 2K The three-positions control post has the protection code IP65. It is used for industrial sectional door (with the shaft type operators) control; there can be connected one near the door or several control posts. The threepositions control post easily connects to an operator and is placed near the door. One button is charged with the door's opening, another, another one for closing. An unauthorized operators starting up is prevented by a key. BUTTON 3 The three-positions control post has the protection code IP65. It is used for industrial sectional door (with the shaft type operators) control; there can be connected one or several control posts. The three-positions control post easily connects to an operator and is placed near to the door. One button is charged with the door's opening, another, another one for closing. The stop button enables to stop the door immediately in any position. Besides, it is possible to control the door step-by-step' by one button. Transmitter 4 Remote control transmitters DoorHan are meant for DoorHan automatics or any other device with the DoorHan radio receiver control. You can control one or more (up to 4) different devices (gates, barriers etc.) with the help of one transmitter. Photocell Photoelectric detector Photocell is a safety device, consisting of infrared transmitter and receiver, which are installed in a gate opening. If an infrared beam is interrupted, the control board receives the signal of an obstacle in a dangerous area of an automatic system operation, and a system reacts as it was preset by the operation logic stop or reverse of gates. KEYSWITCH Key-operated push-button KEYSWITCH is used for giving a control command to an operator's control board. A DIP-switch lets give a control command in the step-by-step mode. One control command is used for opening, stop, and closing. Both NO and NC contacts can be used for connection. In order to give a command you need to turn the key controlling the microswitches contacts; when you release the key, it reverts. SWM SWM key-button is used to give a directive to the drive control unit. It has 2 positions - for opening and closing, In order to give a directive, turn the key that controls the contacts of the microswitchers. If you stop holding the key it will return to its original position. KEYPAD Radio code wireless numeric pad KEYPAD is used for remote control of an electronic operator, equipped with an internal or external receiver DoorHan. WDKIT The WDKIT is used to prevent the drive from starting if the wicket-door is opened, when there s a wicketdoor built in a sectional door. Open wicket sensor WDKIT is a magnet non-contact sensor, designed for the mounting in the wicket-door profile of a sectional door. OPTOKIT The opto-sensors safety device (OPTOKIT) consists of 2 infrared safety sensors: receiver and transmitter, installed in a special rubber profile (RUBBER) at the bottom of the door panel. The deformation of the rubber profile leads to the interruption of the optical beam and a signal is sent to the control unit. The control unit generates a universally recognized signal, which makes it possible to use an opto-sensor kit with various door automation devices. 23

24 2 Automatic systems for sliding gates Sliding gates operator with oil bath technology Sliding series operators Sliding-1300(2100) operators are designed to be used for sliding gates. Pinion rotation is transmitted to linear motion by a rack that is fixed on the gate. Self-blocking reducer enables to block the gate without any locks. Sliding series operators were designed to be used in severe climatic conditions. Their advantages are: key-operated release device makes it possible to open and close the gate manually in case of power cut; built-in control board; low noise level and thermal protection( C). magnetic limit switches operating ambient temperature from -40 to C protection from unauthorized opening control board enables to connect any external receiver high use frequency maximum weight of a gate up to 2100 kg protection class IP54 compliance with Russian and European Safety Standards 24

25 Automatic systems for sliding gates 2 Oil bath technology enables high use frequency 4 adjusting bolts are protected by a plastic cover Magnetic limit switches Built-in control board Operator description 1 Dimensions, mm Built-in control board 2. Electric motor 3. Z16 pinion 4. Limit switches unit 5. Fixing bolts cover 6. Reducer body Sliding series operators technical specifications Model Sliding-1300 Sliding-2100 Power supply 230 V Absorbed current 2,5 А 3,5 А Absorbed power 550 W 750 W Motor rotation speed 1400 rpm Capacitor 22 µf 37 µf Reduction ratio 1:32 Rack 30x12 mod. 4 Pinion Z16 Maximum thrust force 900 N 1350 N Maximum torque 27,5 Nm 43 Nm Thermal protection 125 C Use frequency 70% Operating ambient temperature from -40 to C Protection class IP54 Maximum gate weight 1300 kg 2100 kg Gate speed 10 m/min Limit switches magnetic Dimensions, mm 270х290х200 Weight 15 kg 16 kg 25

26 2 Automatic systems for sliding gates Advanteges Use frequency Sliding series operators are designed with oil bath technology. Constant, complete oil bath lubrication of mechanical components enables much higher heat emission ensuring the highest use frequency. Gate weight Maximum gate weight is the main operator characteristic. The mostly widespread sliding gates weigh not more than 1000 kg. DoorHan operators for sliding gates are designed for gates up to 2100 kg thus enabling to use them both for residential and industrial gates. Moisture protection Good moisture protection ensures long service and no-failure life of the operator. DoorHan operators for sliding gates have waterproof body excluding moisture and dust penetration. Such important units as control board and limit switch unit are housed inside the body. Protection class of the operator (IP54) ensures his no-failure work. Limit switches DoorHan operators for sliding gates are equipped with non-contact magnetic limit switches. Limit switches unit has no projecting parts thus enabling to seal the operator body and ensuring long service life due to absence of mechanical actions. Doubled magnetically operated sealed switches ensure reliable limit switches activation. Operators fixing DoorHan operators for sliding gates have reliable fixing to mounting plate in 4 points. Lateral fixing brackets are galvanized and protected by plastic covers. Release device Operator is non-reversing so no electric lock needs to be installed. In case of the event of power failure the key protected release device makes it possible to open and close the gate manually. Control unit The operator is equipped with Italian control board which ensures maximum safety and functionality. Built-in control board ensures easy connection of any control and safety devices. Digital display and leds enable to control the adjustments and the state of the gate. Safety DoorHan operators comply with all Russian and European Safety Standards. Anty-crashing safety system ensures the safe work of automatic system. Quality control 100% DoorHan operators undergo quality control for more than 15 criteria before shipment. 26

27 Automatic systems for sliding gates 2 Package 1.Operator with built-in control board 2.Instruction manual 1pcs. 1 pcs. 3. Key-button 1 pcs. 4.Rack (1m length) 5.Photocells 6.Signaling lamp 7.Receiver 8.Mounting plate 4 pcs. 1 pcs. 1 pcs. 1 pcs. 1 pcs. Control board 0,5 А SW1 TimerW AutoCL Force PWR a b 2,5 А DIP St Ped PH1 PH2 STOP SW1 SW2 _ Start Ped _ PH OP PH CL EMRG SW Cl SW Op _ +24V +24V _ L1 L2 Com Lamp L N PE 220 В 50 Гц Control board specifications Power supply Absorbed power Motor max. load Accessories max. load Operating ambient temperature Fuses Function logic Work time Pause time Thrust force Terminal board inputs Programming 230 V 10 W 1000 W 0.5 A from -20 to C 2 (5A - motor) Automatic/ Stepped automatic / Semi-automatic/ Stepped semi-automatic/safety/semi-automatic B/ Dead man C/ Mixed B+C Programmable (from 0 to 10 min) Programmable (from 0 to 4 min) Adjustable over 50 levels Open/Partially open/opening safety devices/ Closing safety devices/stop/edge/power supply+earth (+,-,F) buttons and display 27

28 2 Automatic systems for sliding gates Installations 2 2х1,5 4 5 TX 3 2х0,5 3х0,5 RX х0,5 1. Operator 2. Signaling lamp 3. Photocells 4. Key-button 5. Radio keypad unit 6. Rack 1. Position the operator on foundation plate to ensures the rack meshes correctly with the pinion. Fix the operator. 2. Release the operator. 3. Route the cables through the appropriate openings in the operator body. 4. Mount the racks. 5. Lower the gearmotor position by about 2-3 mm to ensure the correct work. 6. Manually check if the gate moves correctly. Rack 28 Ground Pinion

29 Automatic systems for sliding gates 2 Accessories LAMP The signal lamp «LAMP»is a safety device emitting a flashing light signal warning when the door is in movement. Depending on the device contacted, there could be realized the preliminary flashing mode (the lamp flashes during a particular period of time before the gate starts moving). Transmitter 4 Remote control transmitters DoorHan are meant for DoorHan automatics or any other device with the DoorHan radio receiver control. You can control one or more (up to 4) different devices (gates, barriers etc.) with the help of one transmitter. Photocell Photoelectric detector Photocell is a safety device, consisting of infrared transmitter and receiver, which are installed in a gate opening. If an infrared beam is interrupted, the control board receives the signal of an obstacle in a dangerous area of an automatic system operation, and a system reacts as it was preset by the operation logic stop or reverse of the gates. RACK Gear rack is used for sliding gates moving. KEYSWITCH Key-operated push-button KEYSWITCH is used for giving a control command to an operator's control board. A DIP-switch lets give a control command in the step-by-step mode. One control command is used for opening, stop, and closing. Both NO and NC contacts can be used for connection. In order to give a command you need to turn the key controlling the microswitches contacts; when you release the key, it reverts. SWM SWM key-button is used to give a directive to the drive control unit. It has 2 positions - for opening and closing, In order to give a directive, turn the key that controls the contacts of the microswitchers. If you stop holding the key it will return to its original position. KEYPAD Radio code wireless numeric pad KEYPAD is used for remote control of an electronic operator, equipped with an internal or external receiver DoorHan. DHRE-2 External receiver DHRE-2 is meant for other manufacturers automatics control with the help of DoorHan transmitter. It is possible to connect the receiver to any operator, which has normal opened (NO) control contacts. This receiver works on a frequency 433 MHz. The receiver DHRE-2 has two channels, thus it can control one or two operators. 29

30 2 Автоматика Automatic для распашных systems ворот for swing gates Swing series operators Swing series operators Electromechanically driven Swing operators are designed to be used for swing gates. Swing series operators are non-reversing screw operators and, therefore, do not require electric locks and bolts. In case of the power cut the operator can be easily released by the key. The operator consists of electric motor, reducer coupled with the screw and lead nut. All units are housed in die cast aluminium body preventing their damage. Powerful motor (3000N thrust) and end enlarged rod effective stroke enable to use the operator for leaves with the length of a leaf up to 5m and the weight up to 1000kg. Operator is ideal for big swing gates with medium and high use frequency, leaf opening inwards or outwards. opening and closing limit switches 500 mm rod effective stroke enables outward opening die cast aluminium body prevents operator internal units from damage and protects from aggressive ambient reliable and functional control board operating ambient temperature from -40 to C 30

31 Автоматика Automatic для распашных systems ворот for swing gates 2 Operator description Operator enclosure 2. Rod 3. Nut 4. Gearmotor 5. Front fixing bracket 6. Rear fixing bracket Dimensions, mm /300 Technical specifications Model Swing-3000 Swing-5000 Weight 10 kg 11 kg Power supply 230 V 230 V Absorbed current 1,2 A Absorbed power 150 W Use frequency 50% Protection class IP54 Thrust force 3000 N Rod extension speed 15 mm/sec Operating ambient temperature from -40 to C Dimensions, mm 993x88x126 Rod effective stroke 300 mm 500 mm Leaf maximum length 3 m 5 m Leaf maximum weight 800 kg 1000 kg 31

32 2 Автоматика Automatic для распашных systems ворот for swing gates Optimum decision for residential and industrial gates Swing-5000 is the most practical and economical choice for residential and industrial gates of medium and high area. The non-reversing operator enables to fix a leaf in ultimate positions and, therefore, does not require electric locks and bolts. Fast and easy installation It is just necessary to fasten the front fixing bracket to the leaf and the rear fixing bracket to the pilaster without any additional attachments. Safety 452 MPS electronic control board ensures anti-crashing safety due to direct control operator drive torque. In case of emergency or power cut the release key makes it possible to move the gate manually. Higher reliability - less maintenance work Swing-5000 operator doesn t require special maintenance work and is notable for minimum operating cost. Electromechanical limit switches enable a smooth stop in ultimate points also prolonging operator life. Maximum durability Die cast aluminium enclosure with special treatment ensures IP54 protection class and operator units protection from mechanical damage and aggressive ambient. Long life wear-resistant surface saves operator effective appearance. Fast and easy activated release system Midget three-edged key activated reliable release system enables to move the gate manually in case of power cuts. Release unit waterproof cover prevents moisture penetration inside the system. Simplified connection Both motor and limit switches are connected by a single three-wire cable. Usability and functionality 452 MPS control board ensures the improvement of the automatic system functionality enabling to connect photocells, the usage of auto closing function and pedestrian passage, the adjustment of the operators drive torque. Rod Special shape rod guarantees better rod-nut transmission kinematic characteristics. Special shape screw thread ensures lubricant keeping in friction zone enabling to raise operator wear-resistance and smoothness of running meanwhile reducing noise level. 32

33 NC NO Автоматика Automatic для распашных systems ворот for swing gates 2 Package 1. SWING-5000 operator 2 pcs. 2. Instruction manual 1 pcs. 3. Fixing kit 2 pcs. 4. Key-switch 1 pcs. 5. Signaling lamp 1 pcs. 6. Photocells 1 pcs. 7. Receiver 1 pcs. 8. Control board 1 pcs. 9. Enclosure for control board 1 pcs. Control board PCB-SW Power + _ F Tr M1 M2 Photo PE N L COM OP CL COM OP CL OP CL COM Lamp S-B-S PED Stop +24 V S.LOCK COM NO NC Gnd +24 Com Out Gnd +24 Technical specifications Power supply 230 V Absorbed power 10 W Motor max. load 800 W Accessories max. load 0.5 A Electric lock max. load 15VA Operating ambient temperature from -20 to C Fuses 0.8 A accessories, 5A motor Function logics Automatic/Semi-automatic/Safety operated/ Stepped semi-automatic/ Dead man C Work time Programmable (from 0 to 120 s) Pause time Programmable (0, 10, 20, 30, 60, 120 s) Closing leaf delay 0, 5, 10, 20 s Opening leaf delay 2 s (can be disabled) Thrust force 8 levels Terminal board outputs Lamp/Motor/+24V,-24V/Indicator light/photocells test/electric lock Terminal board inputs Open/Partial open/closing safety devices/opening safety devices/stop/power supply+earth 33

34 2 Автоматика Automatic для распашных systems ворот for swing gates Leaf width, m Leaf weight, kg Installation dimensions Pilaster Hinge Leaf(closed) Opening angle А, mm В, mm Cmax, mm 90 о о Installations 1. Transmitter 2. Signaling lamp 3. External reciver 4. Key button 5. Operator 6. Photocells 7. Control unit enclosure 8. Photocells 9. Electric lock 34

35 Автоматика Automatic для распашных systems ворот for swing gates Accessories 2 LAMP The signal lamp «LAMP»is a safety device emitting a flashing light signal warning when the door is in movement. Depending on the device contacted, there could be realized the preliminary flashing mode (the lamp flashes during a particular period of time before the gate starts moving). Transmitter 4 Remote control transmitters DoorHan are meant for DoorHan automatics or any other device with the DoorHan radio receiver control. You can control one or more (up to 4) different devices (gates, barriers etc.) with the help of one transmitter. Photocell Photoelectric detector Photocell is a safety device, consisting of infrared transmitter and receiver, which are installed in a gate opening. If an infrared beam is interrupted, the control board receives the signal of an obstacle in a dangerous area of an automatic system operation, and a system reacts as it was preset by the operation logic stop or reverse of gates. KEYPAD Key-operated push-button KEYSWITCH is used for giving a control command to an operator's control board. A DIP-switch lets to give a control command in the step-by-step mode. There is used one control command for opening, stop and closing. There can be used both NO and NC contacts for connection. In order to give a command you need to turn the key controlling the microswitches contacts; when you release the key, it reverts. DHRE-2 External receiver DHRE-2 is meant for other manufacturers automatics control with the help of DoorHan transmitter. It is possible to connect the receiver to any operator, which has normal opened (NO) control contacts. This receiver works on a frequency 433 MHz. The receiver DHRE-2 has two channels, thus it can control one or two operators. KEYSWITCH Radio code wireless numeric pad KEYPAD is used for remote control of an electronic operator, equipped with an internal or external receiver DoorHan. SWM SWM key-button is used to give a directive to the drive control unit. It has 2 positions - for opening and closing, In order to give a directive, turn the key that controls the contacts of the microswitchers. If you stop holding the key it will return to its original position. 35

36

37 Barriers

38 3 Barriers Barrier Barrier series automatic barriers Electromechanical barrier BARRIER is meant for automation of the passages with the opening up to 6 meters. The construction of the barrier s motor-reducer enables to use it with the high intensity. BARRIER perfectly can be used in severe operation conditions and conforms to the required safety conditions. Thanks to the reinforced reducer, the barrier has a high reliability and long working life. The barrier consists of a beam and a cabinet, which has a motor-reducer, balancing mechanism and a control board inside. Heavy duty gear wheels of reducer. Non-contact magnet limit switches. Bottom profile is made of the frost-resisting polymeric material. Any additional device can be installed. High use frequency. The barrier can be easily released and operated manually. 38

39 Barriers 3 Dimensions, mm till 6 m 1050 mm 300 mm Technical specifications Model Barrier Maximum beam length 6 m Opening time 5-7 s Power supply 230 V Type of beam Rectangular, aluminium Use frequency (t=20 0 C) 70% Dimensions, mm 270x1015x140 Motor rotation speed 1400 rpm Absorbed power 220 W Thermal protection 120 o C Operating ambient temperature from to C (from C with thermal heater) Protection class IP54 Limit switches magnetic 39

40 3 Barriers Advantages Use frequency Thanks to a particular reducer, the barrier has high usage intensity, that is a very important advantage in the passage automatization. The self-locking reducer guarantees a smooth movement and an accurate positioning of a beam in the limit points. In spite of a quite fast opening/closing speed, the smooth stop in the limit points helps to avoid a dynamical load of the system, and thus extends the barrier service life. Balancing mechanism The balancing mechanism of the barrier has two specially selected springs, that significantly depress the load on the load-bearing elements of the operator. The mechanism includes springs with an extended length. While operating they are loaded and distorted little, and they can be heavy used during all the period of the barrier s service. Besides, the springs have a special corrosion-resistant coating. Reliability Thanks to the simple design of the operator and to the usage of the heavy-duty gear wheels of the reducer, the barrier has a long service life; besides, the operator doesn t overheat even when it is used heavily. The construction of the electrical operator has low-sensitivity of the balancing adjusting thus simplifying its startup. The barrier s cabinet protects the internal elements from aggressive ambient. Aluminum beam The aluminum beam with reflective stickers has special reinforced elements in the fixation point, that securely fix it on a cabinet. If any objects appear during the opening, the bottom damper protects against the impact. The beam s fastening is protected by a decorative plastic cover. Safe The barrier is equipped with a control board, which meets all the required safety conditions. The control board enables the adjustment of the beam s lowering force and prevents from an impact, if any objects are appeared in the operating zone of a beam. It is placed in a special control box, which is well located inside the barrier s cabinet. In order to provide the barrier startup as soon as possible, all the needed connections are already completed. Built-in emergency release The barrier can be easily released and operated manually in case of power cut. The balancing mechanism enables an easy raise of the beam. In order to provide maximum comfort and safety, any additional devices can be installed on the barrier. 40

41 Barriers 3 Package 1. Cabinet with built-in control board 1pc. 2. Instruction manual 1pc. 3. Key-button 1pc. 4. Photocells 1pc. 5. Signaling lamp 1pc. 6. Beam 1pc. 7. Fixing kit 1pc. 8. Beam support 1pc. Control board 0,5 А SW1 TimerW AutoCL Force PWR a b 2,5 А DIP St Ped PH1 PH2 STOP SW1 SW2 _ Start Ped _ PH OP PH CL EMRG SW Cl SW Op _ +24V +24V _ L1 L2 Com Lamp L N PE 220 В 50 Гц Technical specifications Power supply Absorbed power Motor max. load Accessories max. load Operating ambient temperature Fuses Function logic Work time Pause time Thrust force Terminal board inputs Programming 230 V 10 W 1000 W 0.5 A from -20 to C 2 (800mA - accessories, 5A - motor) Automatic/ Stepped automatic / Semi-automatic/ Stepped semi-automatic/safety/semi-automatic B/ Dead man C/ Mixed B+C Programmable (from 0 to 10 min) Programmable (from 0 to 4 min) Adjustable over 50 levels Open/Partially open/opening safety devices/ Closing safety devices/stop/edge/power supply+earth (+,-,F) buttons and display 41

42 2 Barriers Accessories LAMP The signal lamp «LAMP»is a safety device emitting a flashing light signal warning when the door is in movement. Depending on the device contacted, there could be realized the preliminary flashing mode (the lamp flashes during a particular period of time before the gate starts moving). Transmitter 4 Remote control transmitters DoorHan are meant for DoorHan automatics or any other device with the DoorHan radio receiver control. You can control one or more (up to 4) different devices (gates, barriers etc.) with the help of one transmitter. Photocell Photoelectric detector Photocell is a safety device, consisting of infrared transmitter and receiver, which are installed in a gate opening. If an infrared beam is interrupted, the control board receives the signal of an obstacle in a dangerous area of an automatic system operation, and a system reacts as it was preset by the operation logic stop or reverse of gates. FOOT The stationary support of the barrier s beam. It is used for a fixation of the beam, when it is closed and enables to minimize a wind load. KEYSWITCH Key-operated push-button KEYSWITCH is used for giving a control command to an operator s control board. A DIP-switch lets give a control command in the step-by-step mode. There is used one control command for opening, stop and closing. There can be used both NO and NC contacts for connection. In order to give a command you need to turn the key controlling the microswitches contacts; when you release the key, it reverts. KEYPAD Radio code wireless numeric pad KEYPAD is used for remote control of an electronic operator, equipped with an internal or external receiver DoorHan. DHRE-2 External receiver DHRE-2 is meant for other manufacturers automatics control with the help of DoorHan transmitter. It is possible to connect the receiver to any operator, which has normal opened (NO) control contacts. This receiver works on a frequency 433 MHz. The receiver DHRE-2 has two channels, thus it can control one or two operators. OPTOKIT The opto-sensors safety device (OPTOKIT) consists of 2 infrared safety sensors: receiver and transmitter, installed in a special rubber profile (RUBBER) at the bottom of the door panel. The deformation of the rubber profile leads to the interruption of the optical beam and a signal is sent to the control unit. The control unit generates a universally recognized signal, which makes it possible to use an opto-sensor kit with various door automation devices. 42

43 Rolling shutters, screens and awning automatics

44 4 Rolling shutters, screens and awning automatics Rolling shutters, screens and awning automatics DoorHan rolling shutter systems automation will make your life comfortable Automatic control At the present time easy automatic control of different kinds of systems becomes more and more popular, as it has incontestable advantage over any hand drive. Rolling systems, controlled both by mechanical operators and automatically (with the help of tubular motors), is no exception. You can control rolling shutters by different types of switches or by remote (radio) control transmitters. Easy touch of a transmitter's button you can open one or any number of rolling shutters. DoorHan Company developed the full range of tubular motors, electronic devices and accessories for automatic control of rolling shutters and rolling door, sun awnings, automatic screens. It is often very inconvenient or even impossible to control large size rolling systems, rolling doors by means of a mechanical drive. In this case an automatic is needed. Moreover, few people like to close many rolling shutters manually it takes much time and force. DoorHan automatics save you these inconveniences, if you control the particular group of rolling shutters by single button. 44

45 Rolling shutters, screens and awning automatics 4 DoorHan rolling shutters automatics are mainly used for many systems automation. Rolling systems Sun awnings Automatic screens Rolling sun screens 45

46 4 Rolling shutters, screens and awning automatics Tubular motor DoorHan. 2. Emergency control cardan joint RK7S, RK7E. 3. Emergency control loop PP Control boards: 4.1 group control GC2, GC4; 4.2 remote control, series 1 CV, CV0.1, CV0.3; 4.3 remote control, series 2 CV2.1, CV Photoelectric detector safety devices Photocell. Switches ACPE, ACSE, ACPES. 46

47 Rolling shutters, screens and awning automatics 4 DoorHan tubular motors DoorHan tubular motors DoorHan tubular motors are mainly used for rolling shutters, sun awnings, screens and venetian blinds automation. DoorHan tubular motors combine high quality, easy mounting and service. Under the DoorHan trademark you get high-tech operator, which technical characteristics exceed well-known European suppliers' operators. Everything needed for mounting is already included in a kit of electromotor: support plate and a set of adapters. We offer a lot of accessories for tubular motors with emergency manual opening function. Steel body and gear wheels of reducer. Brass shafts and gear wheels of limit switches unit. 100% quality control. Durable aluminum body of limit switches unit. 47

48 4 Rolling shutters, screens and awning automatics Series 35 Motor Torque, Nm Rotation speed, rpm Tube diameter, mm Supply voltage, V Power, W Length L, mm Limit switch rotation Continuous working time, min. Protection class Tubular motor for the shaft RV40 (series 35) RS10/ IP44 Adapters and support plate used DL44 DH36 48

49 Rolling shutters, screens and awning automatics 4 Series 45 Motor Torque, Nm Rotation speed, rpm Tube diameter, mm Supply voltage, V Power, W Length L, mm Limit switch rotation Continuous working time, min. Protection class Tubular motor for the shafts RV60, RV70 without emergency opening reducer (series 45) RS10/ IP44 RS20/ IP44 RS30/ IP44 RS40/ IP44 RS50/ IP44 Adapters and support plate used DL39 DH05 49

50 4 Rolling shutters, screens and awning automatics Series 45M Motor Torque, Nm Rotation speed, rpm Tube diameter, mm Supply voltage, V Power, W Length L, mm Limit switch rotation Continuous working time, min. Protection class Tubular motor for the shafts RV60, RV70 with emergency opening reducer (series 45M) RS10/15M IP44 RS20/15M IP44 RS30/15M IP44 RS40/15M IP44 RS50/12M IP44 Adapters and support plate used DL39 DH05 BU100K 50

51 Устройства управления Rolling shutters, screens and awning automatics 4 Series 45R Motor Torque, Nm Rotation speed, rpm Tube diameter, mm Supply voltage, V Power, W Length L, mm Limit switch rotation Continuous working time, min. Protection class Tubular motor for the shaft RV70 with emergency release (series 45R) RS50/12R IP44 Adapters and support plate used DH11 DL60 DZ183A 51

52 4 Устройства Rolling управления shutters, screens and awning automatics Series 55 Motor Torque, Nm Rotation speed, rpm Tube diameter, mm Supply voltage, V Power, W Length L, mm Limit switch rotation Continuous working time, min. Protection class Tubular motor for the shafts RV70, RV102 without emergency opening reducer (series 55) RS60/ IP44 RS80/ IP44 RS100/ IP44 Adapters and support plate used DH215 DL32 BU100K 52

53 Устройства Rolling управления shutters, screens and awning automatics 4 Series 55M Motor Torque, Nm Rotation speed, rpm Tube diameter, mm Supply voltage, V Power, W Length L, mm Limit switch rotation Continuous working time, min. Protection class Tubular motor for the shafts RV70, RV102 with emergency opening reducer (series 55M) RS60/12М IP44 RS80/12М IP44 RS100/10М IP44 Adapters and support plate used DH215 DL32 BU100K 53

54 4 Rolling shutters, screens and awning automatics Tubular motors load Load, kg Roller tube, mm 10Nm 20Nm 30Nm 40Nm 50Nm 100Nm 54

55 Rolling shutters, screens and awning automatics 4 Tubular motors accessories We offer the range of accessories for emergency opening and a tubular motor mounting. Everything needed for mounting is already included in a kit of electromotor. Loop and cardan joints are forseen in case of an emergency opening. Adapters DH216 Crown DH216 for the DoorHan tubular motor, series 55, for the shaft RV102. DL212 Drive adapter DL212 for the DoorHan tubular motor, series 55, for the shaft RV102. DL60 Drive adapter DL60 for the DoorHan tubular motor, series 45, for the shaft RV70. - plastic, - black, - for shaft rotation. DH51 Crown DH51 for the DoorHan tubular motor, series 45, for the shaft RV70. - plastic, - black, - positioning of limit microswitches. 55

56 4 Rolling shutters, screens and awning automatics Multipurpose fastening plate BU100K Multipurpose fastening plate BU100K for all DoorHan tubular motors for end cap fixation. - galvanized steel Fastering plate for the DoorHan tubular motor, series 35 and 45, without emerging opening DZ183A Fastering plate DZ183A, which is produced from galvanized steel and can be combined only with fixing side cover RS50/12L tubular motors. Emergency opening accessories PP Tinge PP200 for leading out of the emergency control from a shutter box. RK7S 500 Cardan joint RK7S for leading out of the emergency control through a wall. The length of the pin is 500 mm. 56

57 Rolling shutters, screens and awning automatics 4 RK7E Cardan joint RK7E for leading out of the emergency control through a wall. The length of the pin is 1000 mm VRS Crank rod for emergency tubular motor control in case of power cutoff. It is used with the tinge PP200 and cardan joints RK7S and RK7E. VRK Crank rod for emergency tubular motor control in case of power cutoff. It is used with the tinge PP200 and cardan joints RK7S and RK7E. VRP Crank rod for emergency tubular motor control in case of power cutoff. It is used with the tinge PP200 and cardan joints RK7S and RK7E. 57

58 4 Rolling shutters, screens and awning automatics Switches swb Switch 2 buttons for laid-on mounting. - double-pole SWM Key-button prevents from an unauthorized rolling shutters control. It has 2 positions for opening and closing. - double-pole SBH Switch 2 buttons for built-in mounting. - double-pole Control devices of the series 1 GC2 Group control board GC2 for the control of 2 electric operators with help of common switch and separate buttons for each operator. GC4 Group control board GC4 for the control of 4 electric operators. It is used for combining many operators in one group for a simultaneous control. 58

59 Rolling shutters, screens and awning automatics 4 CV01 Remote control board CV01 has the internal receiver for DoorHan s transmitters. It is possible to connect receivers of most rolling shutters and gate automation manufacturers. Transmitter 4 4-channel remote control transmitter is used together with the control board CV01, and can control 4 devices. Control devices of the series 2 ROLL 1 Control device ROLL 1 is used for remote control of 1 tubular motor with help of remote control transmitters T1, T5, T15, T0. ROLL 2 Control device ROLL 2 is used for control of 2 tubular motors with help of remote control transmitters T1, T5, T15, T0. т1 1-channel remote control transmitter T1 is used with control devices of the series 2 CV2.1 and CV2.2. It controls 1 channel. т5 5-channel remote control transmitter T5 is used with control devices of the series 2 CV2.1 and CV2.2. It controls 5 channels simultaneously and separately. 59

60 4 Rolling shutters, screens and awning automatics Т15 15-channel remote control transmitter T15 is used with control devices of the series 2 CV2.1 and CV2.2. It controls 15 channels simultaneously and separately. T15TIMER 15-channel remote control with a beeper is used with ROLL1 and ROLL2 control devices. T15TIMER makes it possible to control 15 channels separately and simultaneously as well as to programme daily time as both individual and simultaneous rolling shutters opening and closing. Control box RHA66 Control box for the control boards of the series 1 has the protection class IP65, what suppose its outdoor mounting. 60

61 All types of automatics accessories

62 5 Accessories All types of automatics accessories Door automatics and accessories, realized by DoorHan company, are wonderful for their high quality and are adapted to the domestic operational conditions. It is easy to install and to control the automatics under the DoorHan trademark; it has high operational characteristics and a modern design. While developing automatics we take into account the most severe safety requirements. All automatics pass through many tests and inspections, and thank to that the highest quality the reliability is guaranteed. The accessories for the DoorHan automatics make gate usage maximum convenient and safety. Remote control transmitters, photoelectric detectors, external receivers and other additional devices are noted for their complete compatibility, reliability, easy and convenient mounting. They perfectly suit for a usage with the DoorHan automatics and also can work with automatics of other suppliers. Compact dimensions, modern design, reliability. High operational characteristics. Easy and convenient mounting and service. Accessories Eternal receiver DHRE-2 Built-in antenna. Simultaneous control of 1 or 2 devices. Compact dimensions. External receiver DHRE-2 is meant for other manufacturers automatics control with the help of DoorHan transmitter. It is possible to connect the receiver to any operator, which has normal opened (NO) control contacts. This receiver works on a frequency 433 MHz. The receiver DHRE-2 has two channels, thus it can control one or two operators. Technical characteristics Model Working frequency Supply voltage Max. quantity of transmitters DHRE MHz 12/24 V AC/DC Quantity of channels pcs Range of working temperatures from -40 to +55 C 62

63 Accessories 5 Remote control transmitter Transmitter 4 16 mln of the rolling code 4 independent channels Ergonomic design Rolling code system KeeLoq Remote control transmitters DoorHan are meant for DoorHan automatics or any other device with the DoorHan radio receiver control. You can control one or more (up to 4) different devices (gates, barriers etc.) with the help of one transmitter. Technical characteristics Model Transmitter 4 Working frequency 433 MHz Quantity of channels 4 Range of working temperatures -40 to +55 C Battery 12 V, type 27А SolarTransmitter Solar powered Metal case 16 mil. combination rolling code 4 independent channels DoorHan remote controls are equipped with a unique double power system. The control has a strong metal case and a solar battery chargeable accumulator. DoorHan remote controls are used to operate DoorHan automation or any other devices connected to DoorHan radio receiver. Model Solar Trans Working frequency 433 MHz Channel quantity 4 Working temperature range from -40 up to +55 C Battery 12 V 27A 63

64 5 Accessories Key-operated push-button KEYSWITCH Reliable return mechanism. Compact case. Easy mounting and connection. Key protected pushing. Key-operated push-button KEYSWITCH is used for giving a control command to an operator's control board. A DIP-switch lets the operator give a control command in the step-by-step mode. There is used one control command for opening, stop and closing. There can be used both NO and NC contacts for connection. In order to give a command you need to turn the key controlling the microswitches contacts; when you release the key, it reverts. Key-operated push-button has a mechanical interlock, which prevents from opening of the cover without an installed and turned key. Technical characteristics Model Voltage at contacts Control contact type KEYSWITCH 24 V DC Protection class IP 54 NO/NC Range of working temperatures from -40 to +55 C Radio code numeric pad KEYPAD Radio code wireless numeric pad KEYPAD is used for remote control of an electronic operator, equipped with an internal or external receiver DoorHan. Radio control commands can be sent only after a serial input of a code (from 0 to 9), which should be equal to the preset entry code. If the dialed code is right, the keypad sounds twice, blinks in green and sends an opening, stop or closing command. If the code is wrong, the keypad blinks in red. The buttons are highlighted while dialing. Technical characteristics Model Working frequency Supply voltage Working distance KEYPAD 433 MHz Protection class IP 54 Range of working temperatures from -40 to +55 C Radio code numeric pad KEYPAD Four numbers coding. Light and audio indication. 2 channels. Protection class IP54. 3 V 50 m 64

65 Accessories Safety devices 5 Photoelectric detector PHOTOCELL Photoelectric detector PHOTOCELL Can be connected with any supply voltage 12/24 V AC/DC. Can be connected with any control contact NO/NC. Compact dimensions let PHOTOCELL be easy installed in a gate opening. Photoelectric detector Photocell is a safety device, consisting of infrared transmitter and receiver, which are installed in a gate opening. If an infrared beam is interrupted, the control board receives the signal of an obstacle in a dangerous area of an automatic system operation, and a system reacts as it was preset by the operation logic stop or reverse of gates. Technical characteristics Model Photocell Working distance up to 25 m Supply voltage 12/24 V AC/DC Current consumption 50 ma Protection class IP 54 Range of working temperatures from -40 to +55 C Automatic equalization angle < ± 10 Control contact type NO/NC Open wicket-door sensor WDKIT 3 m of cable is included. Trip distance setting is modifiable. Compact dimensions. The WDKIT is used to prevent the drive from starting if the wicket-door is opened, when there s a wicket-door built in a sectional door. Open wicket sensor WDKIT is a magnet non-contact sensor, designed for the mounting in the wicketdoor profile of a sectional door. Technical characteristics Dimensions, mm Model Operating time Supply voltage WDKIT 20 ms 12/24 V AC/DC Protection class IP 68 Range of working temperatures from -40 to +55 C Control contact type Standard kit: NO/NC 1. Built-in open wicket-door sensor 1 pc. 2. Twisted cable for a door with a height up to 6 m 1 pc. 3. Terminal box 2 pcs. 65

66 5 Accessories Opto-sensors OPTOKIT Technical characteristics Model Operating time Supply voltage OPTOKIT 16 ms 24 V AC/DC Protection class IP 65 Range of working temperatures from -40 to +55 C Control contact type Output contacts type: NO and NC. Operating time 16 ms. Protection class IP 65. The opto-sensors safety device (OPTOKIT) consists of 2 infrared safety sensors: receiver and transmitter, installed in a special rubber profile (RUBBER) at the bottom of the door panel. The deformation of the rubber profile leads to the interruption of the optical beam and a signal is sent to the control unit. The control unit generates a universally recognized signal, which makes it possible to use an opto-sensor kit with various door automation devices. NO/NC Standard kit: 1. Plastic bamper 2 pcs. 2. Twisted cable for a door with a height up to 6 m 1 pc. 3. Terminal box 1 pc. 4. Opto-sensors: receiver/transmitter with the cable 10,5m 1 pc. 5. Opto-sensors control block IP65 Set Signal lamp LAMP The signal lamp «LAMP»is a safety device emitting a flashing light signal warning when the door is in movement. Depending on the contacted device, the preliminary flashing mode could be realized (the lamp flashes during a particular period of time before the gate starts moving). Technical characteristics Model Supply voltage LAMP 230 V Protection class IP 54 Range of working temperatures от -40 до +55 C Power 25 W Bright, easy noticeable light. Built-in antenna. Modern design. Built-in control board. Dimensions, mm 66

67 Accessories 5 External emergency release LOCK Reliable protection from any breaking. The rope of the release is galvanized, that ensures its reliability in long-term usage. The emergency release was developed especially for the Doorhan sectional door operators, and it also can be combined with all manufacturers garage door operators. The emergency release is stocked with 2 keys. The cover protects the cylinder against foreign objects. The LOCK universal external release device is designed for mounting on sectional doors equipped with overhead gear chains and is recommended to use in case of power failure. The external release device allows the door to be opened from the outside without power supply. The emergency release has a polymer material sleeve of the rope, which protects the rope against a mechanical damage and simplifies its fixation to the door parts. The emergency release is placed in a durable steel body with an anticorrosion finish, which ensures long-term using and an aesthetic appearance. LOCK N Handle with 2 individual keys 1.25 diameter and 4,700 mm long shortenable cable 4.62 mm diameter and 4,520 mm long shortenable braiding for cable Kit for lock-release fastening The release is ideal for overhead operators DoorHan and FAAC. The handle and the key plate are fastened on the outside of the panel. You can easily release the operator by turning the handle. Then you can open the gate manually. The elegant handle will fit into any gate design. The reliable lock mechanism ensures faultless and long operation. Switch 1-button SWITCH Reliable return mechanism. Compact case. Easy mounting and connection. It is possible to use the switch 1 button with any device, which has an impulse signal. The switch 1 button SWITCH is used for giving a control command to an operator's control board. One control command for opening, stop and closing of the garage door. There can be used both NO and NC contacts for connection. Every pushing of the button coinsides with one control command: Open Stop Close Stop. 67

68 5 Rolling systems automatics accessories Control devices of the series 1 Control implementation with the series 1 blocks The main advantage of this series control devices is that it is possible to realize maximum wanted variants of control, associating them in different schemes. With help of the series 1 control boards you can remotely control both one rolling shutter and a group of rolling shutters. It is possible to connect different switches, offered by the DoorHan Company, to the control boards. All control devices of the series 1 have hermetic case with the IP65 protection class, and they suit for outdoor installation. CV01 Remote control board CV01 has the internal receiver for DoorHan s transmitters. It is possible to connect receivers of most rolling shutters and gate automation manufacturers. Technical characteristics of CV01 Supply voltage of the control board Max. commutate current Max. commutating voltage Current rating of fuse actuation Variants of control 230 V, 50 Hz no more than 7 A 230±10 V 4 A by transmitter: up stop down stop up (circled) by push-button: up stop down stop up (circled) Controlled electrical motors 1 Dimensions, mm 90х90х50 Weight, g no more than 400 Range of working temperatures by GOST from -40 to +70 C Electrical protection class by GOST II 68

69 Rolling systems automatics accessories 5 GC2 Group control board GC2 for the control of 2 electric operators with help of common switch and separate buttons for each operator. It is possible to connect a separate switch for each tubular motor. Technical characteristics of GC2 Nominal supply voltage of the control board 230 (+10/-15) V, 50 Hz Max. commutate current no more than 3 A Nominal commutating voltage 230±10 V Controlled electrical motors 2 Dimensions, mm 94х130х57 Range of working temperatures from -20 to +45 C Case protection class by GOST (no protection earth requirement) IP65 Electrical protection class by GOST II GC4 Group control board GC4 for the control of 4 electric operators. It is used for combining many operators in one group for a simultaneous control. Technical characteristics of GC4 Nominal supply voltage of the control board Max. commutate current Nominal commutating voltage 230 (+10/-15) V, 50 Hz no more than 3 A 230±10 V Controlled electrical motors 4 Dimensions, mm 94х130х57 Range of working temperatures from -20 to +45 C Case protection class by GOST Electrical protection class by GOST (no protection earth requirement) IP65 II 69

70 5 Rolling systems automatics accessories Control devices of the series 2 Control implementation with 2 blocks series Control implementation with 2 blocks series. Control devices of the series 2 combine modern ergonomic design, easy installation and electrical connections, more convenient remote control. One of the advantages of the control devices of the series 2 is the three-position control that help of buttons up, stop, down, which are situated not only on the control device, but also on the transmitter. During the control boards connection minimum electrical wiring is used. While control boards connection minimum electric power is used. When using the control devices of the series 2 additional switches are not needed, as the devices already have the control buttons. We offer several variants of one-, two- and fifteen-channels office-style transmitters and one-channel pocket keychain-transmitter. The multichannel transmitters can control a number of tubular motors separately and simultaneously. It is possible to control simultaneously all control devices with the help of the channel on the transmitter. The system combines easy mounting and setting with high efficiency of the devices, which enables to realize many control combinations. You can control the whole group of devices as a unit and divide it into several groups by one transmitter. ROLL1 Control device ROLL1 is used together with the remote control of 1 tubular motor with the help of remote control transmitters T1, T5, T15, T0. «UP» button «REC» button «STOP» button Technical characteristics of ROLL1 «DOWN» button Supply voltage Range of transmitters operation Variants of control 230 V, 50 Hz up to 80 m by 3 positions transmitter and buttons on control device: from the up button rising, from the stop button stop, from the down button lowering. Controlled electrical motors 1 Dimensions, mm 86х86х48 Working frequency, MHz 433, 92/315 Range of working temperatures from -10 to + 50 C Electrical protection class by GOST II midpoint conductor electric drive yellow-green 70

71 Rolling systems automatics accessories 5 ROLL2 Control device ROLL2 is used to control 2 tubular motors with the help of remote control transmitters T1, T5, T15, T0. «UP» button «STOP» button «REC» button «DOWN» button Technical characteristics of ROLL2 Supply voltage Range of transmitters operation Variants of control 230 V, 50 Hz up to 80 m by 3 positions transmitter and buttons on control device: from the up button rising, from the stop button stop, from the down button lowering. Controlled electrical motors 2 Dimensions, mm 86х86х48 Working frequency, MHz 433, 92/315 Range of working temperatures from -10 to + 50 C midpoint conductor electric drive yellow-green electric drive yellow-green 71

72 5 Accessories SWM Reliable anti-vandal metal housing Easy installation and wiring Hermetic rear wall prevents moisture penetration into housing Reliable origin return spring mechanism Protection with a key against unauthorized push SWM anti-vandal two-position key-switch and is used to operate rolling shutter tubular motors. The SWM key-switch is suitable for overhead mounting. It is equipped with a locking to avoid installation or removal of cover without inserted and turned key. Protection rating of housing IP54. Gear rack RACK Corrosion-resistant finish Reliable gearing Aesthetic appearance Gear rack is used for sliding gates moving. Gear racks are joined together and are fixed on a the gate. The length of a gear rack is one meter, and you can take up the required length of the gear body right to the particular gate opening. Thick gears of the rack guarantee a long-term using. Besides, the gear rack has a corrosion-resistant coating, which enables to keep the durability and aesthetic appearance during the all working life. Technical characteristics Model Gear spacing Dimensions, mm М4 12х30х1005 BUTTON2K Protection with a key against unauthorized switching on of operator Locking of buttons without using of the key Compact sizes, can be connected to any shaft operators Dust-and-moisture protection rating IP65 BUTTON2K control station is designed to operate sectional gate shaft operators. It is equipped with protection against unauthorized switching on. 72

73 Accessories 5 BUTTON3 BUTTON 3 three-position control station is supplied together with Shaft operator. Several control stations can be connected to the same operator Self-explanatory control buttons Dust-and-moisture protection rating IP65 The BUTTON3 control station is used to operate sectional gate shaft operators. The control station is supplied together with DoorHan shaft operators and is easy to connect to control unit. This device is also suitable for any other automation. Heater for electric operators Easy-to-mount on operator Automatic engaging at temperature pulldown Suitable for any electric operator The heater HEATER is used for electric operators of gates and barriers during operation at minus temperature. The heater is easy to mount on operator's motor-reducer housing. It begins to work automatically at temperature pulldown. Model Supply voltage 230 Actuation temperature, о С -10 Wattage, W 110 Size Heater 400х90 Receiver 433 Quick connection to FAAC control units No need in wired connection of external receiver To use DoorHan remote control with FAAC operator, you just need to insert the receiver in the connector and to record the remote. Model Receiver 433 Working frequency Supply voltage Antenna length Maximal amount of remotes Operating temperature The receiver is suitable for DoorHan remote controls used with FAAC automation. The compact receiver Receiver 433 is connected to FAAC control units via 5-contact connector and allows to record up to 120 DoorHan remote controls. 433 MHz 12/24 V AC/DC 170 mm 120 шт C 73

74

75 Certificates

76 76 Certificates

77 PLANTS

78 6 PLANTS Moscow Kadan Suzhou Russia, MOSCOW Russia, Moskovskaya obl., Odintsovskij r-n, s. Akulovo, ul. Novaya, 120 Phone: +7 (495) , , fax: +7 (495) Moscow China, SUZHOU Gucun Road 188, Xukou Road, Suzhou, PC: Phone: +86 (512) , , fax: +86 (512) suzhou Czech Republic, KADAN 43201, Kralovsky VRCH 2018 Phone: , fax: kadan 78