8. Illustrated Parts Lists

Transcription

1 Hydraulics B Illustrated Parts Lists To order parts, call the Nordson Customer Service Center or your local Nordson representative. Use these five-column parts lists, and the accompanying illustrations, to describe and locate parts correctly. Using the Illustrated Parts List Numbers in the Item column correspond to numbers that identify parts in illustrations following each parts list. The code NS (not shown) indicates that a listed part is not illustrated. A dash ( ) is used when the part number applies to all parts in the illustration. The six-digit number in the Part column is the Nordson Corporation part number. A series of dashes in this column ( ) means the part cannot be ordered separately. The Description column gives the part name, as well as its dimensions and other characteristics when appropriate. Indentions show the relationships between assemblies, subassemblies, and parts Assembly Subassembly 2 A Part 1 If you order the assembly, items 1 and 2 will be included. If you order item 1, item 2 will be included. If you order item 2, you will receive item 2 only. The number in the Quantity column is the quantity required per unit, assembly, or subassembly. The code AR (As Required) is used if the part number is a bulk item ordered in quantities or if the quantity per assembly depends on the product version or model. Letters in the Note column refer to notes at the end of each parts list. Notes contain important information about usage and ordering. Special attention should be given to notes.

2 B 1-42 Hydraulics UpTime Pack for Pump G See Figure B The UpTime pack for pump G (SP 0, 6:1) provides the parts that should be replaced as part of routine maintenance Service kit, UpTime, pump G, SP, 6: O-ring, Viton, 0.01 x in O-ring, Viton, x 2.12 x 0.06 in Nut, hex, lock, torque, M6, class Cup, piston Retaining ring, internal, 100, push-on Cup, U, Viton O-ring, Viton, 1.7 x 1.6 x in Retaining ring, internal, 106, spiral Washer, 1.04 x in Seal, pump, high-volume O-ring, Viton, ID x 0.70 in Backup ring, single, 7 / 16 in. x 9 / 16 in. 1

3 Hydraulics B Fig. B 1-29 Pump G UpTime Pack Parts A

4 B 1-44 Hydraulics This page left intentionally blank.

5 Hydraulics B 1-4 Piston Pump Parts List See Figure B Service kit, pump G, SP, 6:1, UpTime A Bracket, cover, pump, 14:1, 6:1, SP0 1 B O-ring, Viton, 0.01 ID x in O-ring, Viton, x 2.12 x 0.06 in. 2 C Head, air cylinder Screw, hex head, cap, M6 x 120 mm 4 D Washer, lock, split, M Cylinder, air Plug, pipe, flush, 1 / 16 in., w/sealant Nut, hex, lock, torque, M6, class Washer, piston cup Cup, piston Washer, piston seal Retaining ring, internal, 100, push-on Cup, U, Viton 1 C Service kit, pump mount replacement Screw, hex head, cap, M6 x 0 mm Service kit, fork, magnetic (shifter fork) Nut, lock, bearing, PN Washer, lock, E, bearing, 1.74 in Retaining ring, internal, 106, spiral 1 NOTE A: Order this part to receive a complete pump assembly. B: Used only on Series 100V, 400V, and 00V units. C: Apply high-temperature lubricant, part D: Apply anti-seize compound, part Continued on next page

6 B 1-46 Hydraulics Piston Pump Parts List (contd) Washer, 1.04 x in Seal, pump, high-volume Plug, pipe, socket, flush, 1 / 8 in. 1 D Body, pump Tube, crossover, pump 1 C Backup ring, single, 7 / 16 x 9 / 16 in O-ring, Viton, ID x in. 1 B Hydraulic shaft, 6: Piston Washer, step, 1.0 in. diameter Screw, socket head, low, M8 x 16 mm Cage, ball, siphon Ball, siphon, 440 stainless steel, 0.70 in., Seat, ball, siphon O-ring, Viton, 1.7 x 1.6 x in. 1 B Washer, flat, narrow, M Actuator assembly 1 E Screw, hex head, cap, M x 0 mm 2 A Washer, flat, narrow, M6 2 A NOTE A: Used only on Series 100V, 400V, and 00V units. B: Apply high-temperature lubricant, part C: Apply anti-seize compound, part D: Apply threadlocking adhesive, part E: Refer to Actuator Assembly Parts List.

7 Hydraulics B A Fig. B 1-0 Pump G Parts

8 B 1-48 Hydraulics Actuator Parts List See Figure B Service kit, actuator assembly, SP A Screw, socket head, M x 20 mm Cap, valve Nut, hex, lock, torque, M Service kit, bumper Service kit, spool/sleeve 1 B O-ring, Viton, 0.79 ID x in. 4 C Body, valve Detent, upper Screw, socket head, M4 x 8 mm Service kit, magnetic actuator (magnet assembly) Can Detent, lower Retaining ring, internal, 16, bowed 1 NOTE A: Order this part to receive a complete actuator assembly. B: Apply SP pump lubricating oil, part , to the spool lands. C: Apply high-temperature lubricant, part

9 Hydraulics B Fig. B 1-1 Actuator Parts

10 B 1-0 Hydraulics Solenoid Valve Assembly Parts Lists See Figure B Screw, cross-pan, #10-2 x 0.0 in Connector, male, 1 / 4 in. tube x 1 / 8 NPT Elbow, male, 1 / 4 in. tube x 1 / 8 NPT, Viton Elbow, male, 1 / 4 in. tube x 1 / 4 NPT, Viton Tubing, PTFE, 1 / 4 in. 1 A Adapter, 1 / 4 NPTF Grommet, 0.20 ID in Valve, solenoid, 2 way, 24 VDC, 1 / 8 in Block, mounting Screw, pan head, recessed, M x 10 mm Frame, center 1 B Frame, hose end 1 B Pump assembly 1 C NOTE A: Specify required length when ordering replacement tubing. B: Refer to Frame Assembly Parts List in the Tank section. C: Refer to Piston Pump Parts List.

11 Hydraulics B A Fig. B 1-2 Solenoid Valve Assembly Parts

12 B 1-2 Hydraulics Air Pressure Regulator and Filter Assembly Parts List See Figure B Regulator/filter assembly, 90 psi, 4-hose A Regulator/filter assembly, 90 psi, 6-hose B Regulator, filter, air, 1 / 4 NPT Nipple, brass, 40, 1 / 4 in., 2.0 in. 1 A Nipple, brass, 40, 1 / 4 in.,.00 in. 1 B Gauge, air, 1 / 8 NPT, 90 psi Service kit, filter element Service kit, filter bowl 1 NOTE A: Used only on 4-hose units. B: Used only on 6-hose units Fig. B 1- Air Pressure Regulator/Filter Assembly Parts