MULTI-STAGE SEAWATER (MSS TM ) HIGH PRESSURE PUMPS Overhaul Manual

Size: px
Start display at page:

Download "MULTI-STAGE SEAWATER (MSS TM ) HIGH PRESSURE PUMPS Overhaul Manual"

Transcription

1 MULTI-STAGE SEAWATER (MSS TM ) HIGH PRESSURE PUMPS Overhaul Manual For Desalination Reverse Osmosis Service Models: MSS-15 MSS-20 MSS-30 MSS-40 MSS-50 MSS-55 MSS-70 MSS-75 Main Office Tel: Fax: techsupport@fedco-usa.com FEDCO 800 Ternes Drive Monroe, MI 48162, USA Dubai Office Tel: Fax: techsupport-dubai@fedco.com Technopark, Plot TP10501 Jebel Ali South, PO Box 37603, Dubai, UAE Singapore Office Tel: Fax: techsupport-singapore@fedco.com Singapore Branch 82 Toh Guan Road East #C WaterHub Singapore, For patent coverage visit patent.fedco-usa.com MSS Overhaul Manual, XXXXXX-1

2 Table Of Contents MSS TM Series Warnings and Safety Precautions...5 Inspection of Service Kits Upon Receipt... 5 User Health and Safety... 6 In the Work Area... 6 Electrical Connections and Regulations... 6 Pump Overhaul...7 MSS Pump External Components... 7 MSS Pump Internal Components (MSS- 15/20/30/50/70)... 8 MSS Pump Internal Components (MSS- 40/55/75)... 9 Mechanical Seal Removal Mechanical Seal Installation HPSC Mechanical Seal Removal HPSC Mechanical Seal Installation Shaft Position Sensor Removal Shaft Position Sensor Installation Balance Disc Replacement Balance Disc Inspection Balance Disc Wear Chart Balance Disc Installation Stage Removal Stage Assembly Specifications...42 Cleaning Inspection Fastener Torque Specifications Pump Alignment Specifications Balance Disc Specifications Lubricants and Compounds Notes

3 Item Part Description BDK Balance Disc Kit MSK Mechanical Seal Kit MSK HP Mechanical Seal Kit HPSC OHK Overhaul Kit TNK Throttle Nipple Kit TNK HP Throttle Nipple Kit HP STG Stage Kit SHT Shaft Kit ORK O-Ring Kit ORK HP O-Ring Kit HP RRK Retaining Ring Kit RRK HP Retaining Ring Kit HP FCK Flex Coupling Kit ALK Alignment Kit 1 Shipping plug * 2 Stationary seal retaining ring X X X 3 Inlet washer X X X 4 Mechanical seal X X X 5 Mechanical seal shaft washer X X X 6 Rotating seal retaining ring X X X X 7 Inlet O-ring X X X X 8 Split collar retaining ring (MSS-15/20/30/50/70 only) X X X X 9 Split collar (MSS-15/20/30/50/70 only) X 10 Collar sleeve (MSS-15/20/30/50/70 only) X 11 Inlet ring * 12 Diffuser bearing X X 13 Stage spacer (MSS-15/20/30/50/70 only) X X 14 Diffuser bowl (+ First stage housing for MSS-15/20/30 only) X X 15 Impeller X X 16 Series spacer (MSS-15/20/30/50/70 two shell pumps only) X X 17 Series flange O-ring X X X X 18 Discharge ring * 19 Stage spacer (custom end spacer) X 20 Shaft washer/ balance disc washer X X 21 Bearing holder * 22 Balance disc key X X 23 Balance disc O-ring X X X X 24 Balance disc X X 25 Cavity cover O-ring X X X X 26 Discharge housing O-ring X X X X 27 Balance disc flatwasher X X 28 Balance disc lockwasher X X 29 Balance disc nut X X 30 Discharge housing retaining ring X X X 31 Pump shaft X 32 HP shaft bushing anti-roll pin X 33 HP shaft bushing X 34 HP shaft bushing O-ring X X 35 HPSC O-ring X X 36 HPSC retaining ring X X 37 Assembled flex coupling X X 38 Shaft key X X 39 Alignment pins X 40 SS shim set X 41 Throttle nipple elbow X X 42 Throttle nipple X X 43 Throttle nipple O-ring X X X X X X 44 Split cone (MSS-45/55/75 only) X X 45 Split cone nut (MSS-45/55/75 only) X X 46 Clamping neck ring (MSS-45/55/75 only) X X 47 Floating neck ring (MSS-45/55/75 only) X X * Not Included in any kit. Can be purchased separately

4 MSS-40/55/ Figure 1 - Service Parts Kits Components

5 Warnings and Safety Precautions Inspection of Service Kits Upon Receipt Review the contents of the packing list to make sure all components have been included. Inspect all components for signs of damage which may have occurred during shipping. If damage is present or if the contents are incomplete, please contact your shipping company or a FEDCO representative before proceeding. Safety practices and precautions for the operation and maintenance of all FEDCO pump products MUST BE FOLLOWED. This information supplements oral or written instructions that may be received. Safety MUST be practiced as part of the standard operating procedures for this equipment during any installation and operation. To ensure that safe operating and maintenance procedures are followed, operators should develop and keep up a program of safety checks and current instructions. This manual contains certain operating and maintenance procedures that involve exposure to potentially hazardous situations. The levels of hazardous situations are as follows: DANGER Hazards which are IMMEDIATELY ACCESSIBLE, and capable of causing SEVERE PERSONAL INJURY OR DEATH. WARNING Hazards which are NOT IMMEDIATELY ACCESSIBLE, but are capable of causing SEVERE PERSONAL INJURY OR DEATH. CAUTION Hazards which are NOT IMMEDIATELY ACCESSIBLE, and can cause PERSONAL INJURY. ELECTRICAL HAZARD Hazards which are related to Electrical Components and can RESULT IN ELECTRICAL RISKS, SHOCK, ELECTROCUTION OR DEATH if instructions are not followed properly. PUNCTURE HAZARD Hazards which are NOT IMMEDIATELY ACCESSIBLE and can RESULT IN SEVERE PERSONAL INJURY OR DEATH if instructions are not followed properly

6 Installation Procedures Continued WARNING All pump and safety precautions must be followed to prevent physical injury to the operator. It is illegal to operate the equipment in an EU member state, which requires CE compliance, if the manual is not written in that state s language. If a translation is needed, please contact a FEDCO representative. CAUTION A pump is a pressure-generating device with rotating parts that can be hazardous. Any device containing generated pressure can rupture, explode or discharge its contents if it is over-pressurized and may possibly result in personal injury, property damage, environmental damage and death. All necessary precautions must be exercised to insure over-pressurization does not occur. FEDCO will not accept responsibility for physical injury, damage or delays caused by a failure to observe the instructions in this manual. WARNING Installation, operation or maintenance of the pump unit in any manner which is not covered in this manual could cause damage to the equipment, serious injury or death. This includes any modification to the equipment or the use of parts not provided by FEDCO. If there is a question regarding the intended use of the equipment, please contact a FEDCO representative before proceeding. CAUTION This manual clearly identifies accepted methods for safe disassembly and assembly. These methods must be strictly adhered to. WARNING Do not use the pump equipment for a different application than originally specified without the approval of a FEDCO representative. WARNING NEVER operate the pump equipment: below the minimum flow rate. when dry. without priming. without proper guards and safety devices installed. with the discharge valve closed. with the suction valve closed. MSS TM Series ELECTRICAL HAZARD Always follow the Lock-out / Tag-out procedure developed by your company before starting any maintenance or repair. Figure 2 - Typical Lock-Out Tag-Out Tag User Health and Safety Safety equipment and PPE (Personal Protection Equipment) should be used in accordance with company regulations. In the Work Area Always keep the work area clean and dry. Avoid all electrical dangers. Be aware of risks from electric shock or arc flash hazards. Utilize adequate lifting equipment and methods. Electrical Connections and Regulations Refer to the motor nameplate for specific electrical operating information. Electrical connections must be made by certified electricians in compliance with all international, national, state, and local regulations and codes. Insure the product is isolated from the power supply and cannot be accidentally energized. Make sure all thermal contacts are connected to a protection circuit according to product specifications. All electrical equipment must be properly grounded. During installation, service and repair, the companies Lock out / Tag out procedure must be followed

7 Pump Overhaul MSS Pump External Components Figure 3 - Pump External Components Item Description Item Description 1 Precision leveling foot 14 Series shell (if equipped) 2 Shell support bracket 15 Series shell O-ring 3 Inlet housing bolts 16 Shell flange bolts 4 Inlet housing O-ring 17 End shell 5 Inlet housing 18 Discharge housing O-ring 6 High pressure seal carrier O-ring (if equipped) 19 Discharge housing 7 High pressure seal carrier (if equipped) 20 Discharge housing retaining ring 8 Leakage bushing 21 Retaining clips 9 Coupling guard screws (part of coupling guard) 22 Retaining clip cap screws 10 Coupling guard 23 Lock washer 11 Motor adapter 24 Throttle nipple 12 Motor adapter bolts 25 Throttle nipple O-ring 13 Flexible coupling 26 Bearing drain line - 7 -

8 Pump Overhaul Continued MSS TM Series MSS Pump Internal Components (MSS-15/20/30/50/70) Figure 4 - Pump Internal Components (MSS-15/20/30/50/70) Item Description Item Description 1 Shipping plug (optional) 20 Shaft washer 2 Stationary seal retaining ring 21 Bearing holder 3 Inlet washer 22 Balance disc key 4 Mechanical seal 23 Balance disc O-ring 5 Mechanical seal shaft washer 24 Balance disc 6 Rotating seal retaining ring 25 Cavity cover O-ring 7 Inlet O-ring 26 Discharge housing O-ring 8 Split collar retaining ring 27 Balance disc flatwasher 9 Split collar 28 Balance disc lockwasher 10 Collar sleeve 29 Balance disc nut 11 Inlet ring 30 Discharge housing retaining ring 12 Diffuser bearing 31 Throttle nipple O-ring 13 Stage spacer 32 Pump shaft 14 Diffuser bowl/ first stage housing 33 HP shaft bushing anti-roll pin 15 Impeller 34 HP shaft bushing 16 Series spacer (two shell pumps only) 35 HP shaft bushing O-ring 17 Series flange O-ring 36 HPSC O-ring 18 Discharge ring 37 HPSC retaining ring 19 Stage spacer (custom end spacer) - 8 -

9 Pump Overhaul Continued MSS Pump Internal Components (MSS-40/55/75) Figure 5 - Pump Internal Components (MSS-40/55/75) Item Description Item Description 1 Shipping plug (optional) 19 Bearing holder 2 Stationary seal retaining ring 20 Balance disc key 3 Inlet washer 21 Balance disc O-ring 4 Mechanical seal 22 Balance disc 5 Mechanical seal shaft washer 23 Cavity cover O-ring 6 Rotating seal retaining ring 24 Discharge housing O-ring 7 Inlet O-ring 25 Balance disc flatwasher 8 Inlet ring 26 Balance disc lockwasher 9 Diffuser bearing 27 Balance disc nut 10 Floating neck ring 28 Discharge housing retaining ring 11 Diffuser 29 Throttle nipple O-ring 12 Clamping neck ring 30 Pump shaft 13 Split cone nut 31 HP shaft bushing anti-roll pin 14 Impeller 32 HP shaft bushing 15 Split cone 33 HP shaft bushing O-ring 16 Series flange O-ring 34 HPSC O-ring 17 Discharge ring 35 HPSC retaining ring 18 Balance disc washer - 9 -

10 Pump Overhaul Continued Mechanical Seal Removal MSS TM Series Item Description 1 Shaft retaining ring 2 Shaft washer 3 Mechanical seal 4 Stationary seal (with O-ring) 5 Inlet washer 6 Inlet retaining ring Mechanical Seal Standard ELECTRICAL HAZARD Make sure to disconnect the power supply to the motor before carrying out component replacement procedures. Follow all Lock out/ Tag out procedures developed by your company before starting any maintenance or repair. Figure 6 - Mechanical Seal Components Mechanical Seal Removal 1. Drain the piping and pump. 2. Disconnect the inlet and outlet piping. 3. Loosen the screws and remove the coupling guards. Figure 7 - Coupling Guard Removal 4. Remove the anchor bolts and washers from shell support bracket(s). Figure 8 - Support Bracket Anchor Bolt Removal

11 Pump Overhaul Continued 5. Remove the motor adapter bolts and washers. Figure 9 - Motor Adapter Bolt Removal 6. Remove the nuts and the top cradle from the precision leveling foot. Figure 10 - Top Cradle Removal 7. Install the alignment pins to prevent damage to mechanical seal and carefully slide pump 30.5 cm (12 inches) away from motor. NOTES: Make sure to support inlet end of the pump on support bracket(s). Figure 11 - Separating Pump from Motor

12 Pump Overhaul Continued 8. Remove the inlet housing bolts and washers from inlet housing. MSS TM Series Figure 12 - Removing Inlet Housing Bolts 9. Remove the motor adapter and shipping plug from the inlet housing. Figure 13 - Removing Motor Adapter and Shipping Plug 10. Remove the inlet retaining ring from the inlet housing. Figure 14 - Removing Inlet Retaining Ring

13 NO YES Figure 15 - Removing Shaft Seal Pump Overhaul Continued 11. Apply soap and water to the shaft and using a suitable tool through the inlet housing, gently push the shaft washer, mechanical seal, stationary seal, and inlet washer toward the end of the shaft and remove. NOTES: Make sure to push the washer only. Do not push on the shaft retaining ring or damage may occur. NOTES: The shaft retaining ring does not need to be removed unless it is distorted or corroded and needs replacement. 12. Inspect the pump shaft, the shaft retaining ring, the inlet seal bore and the pump shaft for any damage. Remove any oil or dirt with a clean cloth. Figure 16 - Inspecting Retaining Ring, Pump Shaft and Bore Mechanical Seal Installation 1. Install the new shaft washer onto pump shaft and slide the washer against the shaft retaining ring. Figure 17 - Installing Shaft Washer

14 Pump Overhaul Continued 2. Slide the new mechanical shaft seal followed by the new stationary seal and inlet washer onto shaft. MSS TM Series Figure 18 - Installing Mechanical and Stationary Seals 3. Press in on the inlet washer and install the inlet retaining ring into the groove on the inlet housing. NOTES: Make sure the inlet retaining ring is completely seated in the inlet housing groove. Figure 19 - Installing Inlet Retaining Ring 4. Install the shipping plug into the motor adapter seat. Figure 20 - Installing Shipping Plug

15 Pump Overhaul Continued 5. Secure the inlet housing to the motor adapter with the inlet housing bolts and lock washers. Figure 21 - Installing Inlet Housing Bolts 6. Apply system compliant anti-seize compound into the pump shaft keyway and install the pump shaft key. NOTES: Key should fit securely with rounded end facing toward the pump. Figure 22 - Installing Pump Shaft Key 7. Carefully slide the pump against the motor making sure the pump shaft key slides smoothly into the flexible coupling. Push the pump by hand until the motor adapter and motor are in contact. NOTES: Make sure pump key shaft does not jam or fall out during installation. 8. Refer to Final Pump Alignment from the installation/ operation manual. Figure 23 - Attaching Pump to Motor

16 Pump Overhaul Continued Optional High Inlet Pressure Seal Replacement MSS TM Series Item Description Item Description 1 HP shaft bushing retaining ring 7 Shaft washer 2 HP shaft bushing O-ring 8 Mechanical seal 3 HP shaft bushing 9 Stationary seal 4 Shaft retaining ring 10 Inlet washer 5 High pressure seal carrier O-ring 11 Inlet retaining ring 6 High pressure seal carrier Figure 24 - High Pressure Seal Carrier Components Mechanical Seal Optional High Inlet Pressure Design ELECTRICAL HAZARD Make sure to disconnect the power supply to the motor before carrying out component replacement procedures. Follow all Lock out/tag out procedures developed by your company before starting any maintenance or repair. HPSC Mechanical Seal Removal 1. Perform Steps 1 through 7 in Mechanical Seal-Standard removal procedure. 2. Disconnect the drain line from the unit inlet and vent line(s) from the high pressure seal carrier. Figure 25 - Disconnecting Drain/ Vent Lines

17 Pump Overhaul Continued 3. Remove the bolts and lock washers from the inlet housing. Figure 26 - Removing Inlet Housing Bolts 4. Remove the motor adapter and shipping plug from the inlet housing. Figure 27 - Removing Motor Adapter and Leakage Bushing 5. Remove the high pressure seal carrier from the inlet housing. Figure 28 - Removing High Pressure Seal Carrier

18 Pump Overhaul Continued 6. Remove the inlet retaining ring, inlet washer, stationary seal, mechanical seal and shaft washer carrier. MSS TM Series Figure 29 - Removing Seal Components 7. Remove the high pressure seal carrier O-ring. Figure 30 - Removing High Pressure Seal Carrier O-Ring 8. Remove the shaft retaining ring, HP shaft bushing and O-ring. NOTES: If retaining ring appears worn or distorted, replace it. NOTES: The graphite shaft sleeve retaining ring does not need to be removed unless it is distorted or corroded and needs replacement. Figure 31 - Removing Graphite Sleeve Components

19 Pump Overhaul Continued 9. Inspect the high pressure seal carrier and inlet housing seal bores and shaft area for excessive wear or damage. Remove any oil of dirt with a clean cloth. Figure 32 - Inspecting Seal Carrier and Pump Shaft HPSC Mechanical Seal Installation 1. Lubricate and install a new O-ring with the HP shaft bushing and shaft retaining ring. NOTES: Make sure the anti-rotation pin slot is aligned with the top of the shaft. NOTES: Make sure the graphite shaft sleeve retaining ring is completely seated in shaft groove. Figure 33 - Installing Graphite Sleeve Components 2. Install the new high pressure seal carrier O-ring. Figure 34 - Installing New High Pressure Seal Carrier O-ring

20 Pump Overhaul Continued 3. Install the new shaft washer, mechanical seal, stationary seal and inlet washer. Secure with the inlet retaining ring. NOTES: Make sure the inlet retaining ring is completely seated in the high pressure seal carrier groove. MSS TM Series Figure 35 - Installing Seal Components 4. Position the high pressure seal carrier against inlet housing. NOTES: Make sure graphite shaft sleeve lines up with anti-rotation pin in high pressure seal carrier. Figure 36 - Aligning Graphite Shaft Sleeve 5. Install the shipping plug into the motor adapter seat. NOTES: For units equipped with a high pressure seal carrier, make sure the shipping plug is installed with the stepped portion of the bushing facing inward toward the motor adapter. Figure 37 - Installing Leakage Bushing

21 Pump Overhaul Continued 6. Install the motor adapter. Figure 38 - Installing Motor Adapter 7. Secure the motor adapter to the high pressure seal carrier and inlet housing with bolts and lock washers. Figure 39 - Installing High Pressure Seal Carrier Bolts 8. Connect the drain lines to the unit inlet and any vent lines to the high pressure seal carrier NOTES: Make sure the vent line is clean and unplugged. The line should be vented to the atmosphere and positioned to drain normally or connected to a low pressure manifold behind the first high pressure pump in the train. Under no circumstances should the vent line be plugged. A plugged vent line will result in insufficient water lubrication of the seal and balance disc causing internal damage to the unit. Figure 40 - Installing Drain/ Vent Lines 9. Perform Steps 6, 7 and 8 in Mechanical Seal Installation procedure in the previous section

22 Pump Overhaul Continued Optional Shaft Position Sensor Replacement MSS TM Series Item Description 1 Light emitting diode 2 Adjustment shaft locknut 3 Shaft position sensor 4 Shaft collar 5 Spacer plate Figure 41 - Shaft Position Sensor Components Optional Shaft Position Sensor ELECTRICAL HAZARD Make sure to disconnect the power supply to the motor before carrying out component replacement procedures. Follow all Lock out/tag out procedures developed by your company before starting any maintenance or repair. Shaft Position Sensor Removal 1. Disconnect the shaft position sensor from its power source. 2. Loosen the adjustment locknut at the top of the spacer plate. Adjustment Locknut Figure 42 - Loosening Adjustment Locknut

23 Pump Overhaul Continued 3. Unscrew and remove the shaft position sensor from the spacer plate. Figure 43 - Removing Shaft Position Sensor 4. Inspect the shaft collar to ensure it has not moved from its position on the pump shaft. NOTES: If the shaft collar has moved on the pump shaft, inspect the set screw keyway on the pump shaft for excessive wear. SHAFT COLLAR SET SCREW SET SCREW KEYWA Figure 44 - Inspecting Shaft Collar Shaft Position Sensor Installation CAUTION DO NOT supply the shaft position sensor with current and voltage higher than the sensor is rated to operate at. Higher than rated electrical current or voltage may damage the sensor. Figure 45 - Installing Shaft Position Sensor 1. Connect a temporary power supply to the shaft position sensor which will allow the sensor to rotate. 2. Loosely thread the shaft position sensor into the spacer plate

24 Pump Overhaul Continued 3. Slowly rotate the sensor clockwise until the sensor becomes illuminated with a green and red light. Once the sensor is illuminated, rotate the sensor a further one quarter (1/4) turn. ROTATE 1/4 TURN AFTER SENSOR ILLUMINATES MSS TM Series Figure 46 - Adjusting Shaft Position Sensor 4. Tighten the adjustment locknut to prevent sensor movement. NOTES: If a false shut down occurs after the adjustment procedure, loosen the adjustment locknut and rotate the sensor a further onequarter (1/4) turn to ensure no misadjustment has occured. TIGHTEN ADJUSTMENT LOCKNUT 5. Once the sensor is properly adjusted, disconnect the sensor from the temporary power supply and permanently connect the sensor to the VFD. Figure 47 - Tightening Adjustment Locknut

25 Pump Overhaul Continued Balance Disc Replacement Item Description Item Description 1 Cap screw 10 Lock washer 2 Lock washer 11 Washer 3 Retaining clip 12 Balance disc 4 Discharge housing retaining ring 13 Balance disc O-ring 5 Discharge housing O-ring 14 Balance disc key 6 Discharge housing 15 Balance disc washer 7 Cavity cover O-ring 16 Bearing carrier 8 cavity cover 17 Throttle nipple O-ring 9 Pump shaft nut 18 Throttle nipple Figure 48 - Balance Disc Componets

26 Pump Overhaul Continued MSS TM Series ELECTRICAL HAZARD Make sure to disconnect the power supply to the motor before carrying out component replacement procedures. Follow all Lock out/tag out procedures developed by your company before starting any maintenance or repair. Balance Disc Removal 1. Drain the piping and pump. 2. Disconnect the outlet piping. 3. Disconnect the bearing drain line from the throttle nipple. Figure 49 - Disconnecting Drain Line 4. Remove the throttle nipple from the discharge housing. Figure 50 - Removing Throttle Nipple 5. Remove the throttle nipple O-ring from the discharge housing. Figure 51 - Removing Throttle Nipple O-Ring

27 Pump Overhaul Continued 6. Remove the cap screws, lock washers and retention clips from the discharge housing. Figure 52 - Removing Discharge Housing Cap Screws 7. Remove the discharge housing retaining ring and discharge housing with O-ring from the end shell. Figure 53 - Removing Discharge Housing 8. Remove the cavity cover with O-ring. Figure 54 - Removing Cavity Cover

28 Pump Overhaul Continued 9. Loosen the screws and remove the coupling guards. MSS TM Series Figure 55 - Removing Coupling Guards 10. Lock the flexible coupling in place with a suitable strap or chain wrench to prevent pump shaft rotation. SUITABLE STRAP OR CHAIN WRENCH Figure 56 - Securing Pump Shaft 11. Remove the shaft nut, lock washer and washer from the pump shaft. Figure 57 - Removing Shaft Nut and Washers

29 Pump Overhaul Continued 12. Remove the bearing carrier with the balance disc from the end shell. Figure 58 - Removing Bearing Carrier and Balance Disc 13. Remove the balance disc key, washer and O-ring from the pump shaft. Figure 59 - Removing Balance Disc Washer and Key

30 Pump Overhaul Continued Balance Disc Inspection 1. Inspect the surfaces of the balance disc for unusual wear. The surfaces may have some wear but should be smooth. FRONT SIDE MSS TM Series REAR REAR FRONT Figure 60 - Inspecting Balance Disc 2. Measure the balance disc outer hub thickness. Refer to the Balance Disc Wear Chart for wear limit specifications. The maximum acceptable balance disc wear is mm (0.020 ). If the balance disc wear exceeds its wear limit, it must be replaced Balance Disc Model MSS-15 through MSS-75 Balance Disc Wear Chart Original Thickness When New 13.5 mm (0.53 ) Wear Limit mm (0.020") 13.0 mm (0.51 ) IF DISC IS WORN MORE THAN mm (0.020 ) FROM ORIGINAL THICKNESS, REPLACE BALANCE DISC Figure 61 - Measuring Balance Disc 3. Inspect the bearing carrier for unusual wear or scoring and replace if necessary. Figure 62 - Inspecting Bearing Carrier

31 Pump Overhaul Continued Balance Disc Installation 1. Carefully install the bearing carrier into the end shell. NOTES: Grasp pump shaft and lift so that bearing carrier is seated flush against the diffuser housing. Make sure the discharge housing anti-rotation pin is aligned with the top of the pump. Figure 63 - Installing Bearing Carrier 2. Install balance disc washer and seat on the balance disc retaining ring. Lubricate and install the balance disc O-ring. Apply system compliant anti-seize compound to balance disc keyway, and install the balance disc key NOTES: Make sure the balance disc keyway is on top and the key is installed with the rounded end facing outward toward the discharge housing. Figure 64 - Installing Balance Disc Key, Washer and O-Ring 3. Install the balance disc into bearing carrier. NOTES: Make sure the balance disc is firmly seated in the bearing carrier. Figure 65 - Installing Balance Disc

32 Pump Overhaul Continued 4. Apply system compliant anti-seize compound onto the pump shaft threads and install the balance disc washer, lock washer and shaft nut. Tighten to torque value specified in the Fastener Torque Specifications section of this manual. NOTES: The pump shaft nut preload is critical to proper balance disc operation. A properly calibrated torque wrench must be used for this step. APPLY SYSTEM COMPLIANT ANTI-SEIZE COMPOUND MSS TM Series Figure 66 - Installing Balance Disc Washers and Nut 5. Lubricate the cavity cover O-ring and install the cavity cover. NOTES: Make sure to align throttle nipple opening with the bottom of the pump. Figure 67 - Installing Cavity Cover 6. Locate the discharge housing anti-rotation pin on the bearing carrier and note the location of the discharge housing antirotation pin hole. Figure 68 - Discharge Housing Alignment Pin

33 Pump Overhaul Continued 7. Lubricate the discharge housing O-ring and install the discharge housing and retaining ring. NOTES: Make sure to align the throttle nipple opening in the discharge housing with the throttle nipple opening in cavity cover. Figure 69 - Installing Discharge Housing 8. Temporarily install the throttle nipple to ensure the cavity cover and the discharge housing are properly aligned. 9. Remove the throttle nipple. Figure 70 - Inspecting Discharge Housing Alignment 10. Install the retention clips, lock washers and cap screws. Tighten to torque value specified in the Fastener Torque Specifications section of this manual. Figure 71 - Install Discharge Housing Retaining Clips

34 Pump Overhaul Continued 11. Lubricate and install the throttle nipple O-ring into the discharge housing. MSS TM Series Figure 72 - Installing Throttle Nipple O-Ring 12. Apply thread sealing tape to the throttle nipple threads and generously lubricate the non-threaded portion of the throttle nipple. LUBRICATE THREAD SEALING TAPE Figure 73 - Taping Throttle Nipple 13. Gently insert throttle nipple using a clockwise twisting motion to prevent dislodging the throttle nipple O-ring. Figure 74 - Installing Throttle Nipple

35 Pump Overhaul Continued 14. Reconnect the bearing drain line to the throttle nipple. Figure 75 - Connecting Drain Line 15. Remove the strap or chain wrench and install the coupling guards and tighten the screws. Figure 76 - Installing Coupling Guards

36 Pump Overhaul Continued Stage Replacement 4 MSS-40/55/ MSS-15/20/30/50/70 Item Description 1 Stage Spacer 2 Impeller 3 Diffuser Bearing 4 Diffuser Item Description Item Description 1 Diffuser Bearing 5 Split Cone Nut 2 Floating Neck Ring 6 Impeller 3 Diffuser 7 Split Cone 4 Clamping Neck Ring Figure 77 - Stage Components Stage Removal NOTES: Place pump on flat surface in the vertical position. 1. Refer to Balance Disc Removal. 2. Install gauge block to keep shaft from slipping (not provided). Figure 78 - Install and Set Gauge Block 3. Preform the balance disc removal procedure as described earlier in this manual. 4. Remove pump shell (series + endshell or just endshell) bolts from inlet/ flanges. 5. Remove pump shells. Figure 79 - Remove Pump Shell

37 Pump Overhaul Continued 6. Remove custom end spacer (MSS- 15/20/30/50/70 only). 7. Remove discharge ring. NOTES: The end spacer is dimensionally different from the stage spacers and needs to be kept separately. Figure 80 - Discharge Ring Removal 8. Remove diffuser NOTES: The MSS-50 and MSS-70 models have the last diffuser housing welded in the shell and cannot be removed. Figure 81 - Diffuser Removal 9. For: - MSS-15/20/30/50/70 Remove stage spacer and impeller. - MSS-40/55/75 Remove spit cone, split cone nut, and impeller. Figure 82 - Impeller Removal

38 Pump Overhaul Continued NOTES: For two shell pumps: - MSS-15/20/30/50/70 Remove the series spacer between shells. MSS TM Series - MSS-40/55/75 Remove mid inlet ring 10. Repeat stage removal process until all stages are removed. Figure 83 - Series Spacer/ Inlet Ring Removal 11. Remove the first diffuser housing (first stage housing). NOTES: This step is for the MSS-15/20/30 only. This diffuser doesn t include an impeller. Figure 84 - First Stage Housing Removal 12. Shaft will no longer be supported by stages, and will fall over if not supported by the mechanical seal and shipping plug (if installed). NOTES: The shaft must be supported to avoid damage to the bushing and seal. Figure 85 - Shaft Support

39 Pump Overhaul Continued 13. Remove the first spacer (MSS- 15/20/30/50/70 only). 14. Inspect and remove the shaft if necessary. 15. Remove and inspect inlet ring and check for damage, replace if necessary. Figure 86 - Shaft. Inlet Ring Removal Stage Assembly 1. With the pump inlet bolted on to the motor mount. Slide the shaft through the shipping plug and support it on the gauge block. NOTES: Contact FEDCO field service for gauge block height. The pump serial number must be provided. Figure 87 - Shaft Assembly 2. Install inlet ring. 3. Slide on the first spacer and install first diffuser (MSS-15/20/30/50/70 only). NOTES: The MSS-15/20/30 diffuser doesn t include an impeller. Figure 88 - Inlet Ring/ Diffuser Assembly

40 Pump Overhaul Continued 4. For: - MSS-15/20/30/50/70 Install impeller onto the shaft and let it rest on the stage spacer. - MSS-40/55/75 Install diffuser, impeller with spit cone, split cone nut, and stage wear ring. Snug Impeller to shaft, remove temporary spacer washers, and fully tighten split cone nut to specified torque value. 5. Repeat the process until required amount of stages are installed. NOTES: For the MSS-40/55/75, a.095 gap must be present between diffusers to set impeller height. Temporally install spacer washers until the split cone nut is fully tightened. 6. Single Shell Pump: - MSS-15/20/30/50/70 a) Install discharge ring b) Install endshell (reference next step). c) 4X spot weld discharge ring to diffuser (MSS-50/70 only). - MSS-40/55/75 a) Install discharge ring b) Install endshell (reference next step). MSS TM Series Figure 89 - Impeller/ Diffuser Assembly Multi Shell Pump: - MSS-15/20/30/50/70 a) Install series shell (reference next step). b) Install the series spacer between shells. c) 4X spot weld series shell to diffuser (MSS-50/70 only). d) Install remaining stages. e) Install discharge ring and end spacer. f) 4X spot weld final diffuser to discharge ring. (MSS-50/70 only). g) Install endshell (reference next step). h) 4X spot weld discharge ring to endshell (MSS-50/70 only). - MSS-40/55/75 a) Install series shell b) Install mid inlet ring. c) Install remaining stages. d) Install discharge ring. e) Install endshell (reference next step)..095 gap should be set between shells. Figure 90 - Single/ Multi Shell Configurations

41 Pump Overhaul Continued 7. Single Shell Pump: Slide the endshell over the stage stack and fasten into inlet. Multi Shell Pump: Slide the series shell over the stage stack and fasten into inlet. Install shell O-ring and install the endshell and fasten to series shell flange. Figure 91 - Shell Assembly 8. Refer to Balance Disc Assembly

42 Specifications MSS TM Series Cleaning WARNING NEVER use petroleum or alcohol based solvents when cleaning pump components. Solvents can degrade and damage vital seals and O-rings over time. Use fresh water with mild soap (Make sure cleaning chemical are compatible with membranes and other chemicals in the system) and rinse all components thoroughly with fresh water before assembly. Internal Components Clean all internal components with mild soap and fresh water. Rinse thoroughly before use. Internal components should dried with a clean, lint free cloth before assembly. Nameplate Protect nameplate integrity. Use considerable caution when cleaning. Do not use products that may damage painted or engraved surfaces. FEDCO recommends soap and fresh water for cleaning nameplate surfaces. Inspection Internal Components Inspect all internal components for signs of excessive wear or damage. Pay particular attention to bearing surfaces. Replace if necessary. Fasteners Inspect all fastener threads for signs of wear or distortion and replace if necessary. O-Rings Inspect all O-rings for cuts or damage and replace as necessary. WARNING Using compressed air can be hazardous. Observe safety precautions accordingly

43 Specifications Continued Fastener Torque Specifications Item Metric Standard Precision leveling foot top cradle nuts 34 N-m 25 Lb-ft Motor adapter bolts - 3/8" 34 N-m 25 Lb-ft Motor adapter bolts - 1/2" 81 N-m 60 Lb-ft Motor adapter bolts - 5/8" 108 N-m 80 Lb-ft Support bracket adjustment bolts 81 N-m 60 Lb-ft Inlet housing bolts MSS-15 through MSS N-m 24 Lb-ft Inlet housing bolts MSS-90 through MSS N-m 60 Lb-ft Inlet housing bolts (HPSC) MSS-15 through MSS N-m 24 Lb-ft Inlet housing bolts (HPSC) MSS-90 through MSS N-m 60 Lb-ft End shell flange bolts MSS-15 through MSS N-m 60 Lb-ft End shell flange bolts MSS-160 through MSS N-m 81 Lb-ft Series shell flange bolts MSS-15 through MSS N-m 60 Lb-ft Series shell flange bolts MSS-160 through MSS N-m 81 Lb-ft Discharge housing retaining clip cap screws 10 N-m 7 Lb-ft Pump shaft nut (balance disc nut) MSS-15 through MSS N-m 50 Lb-ft Pump shaft nut (balance disc nut) MSS-90 through MSS N-m 70 Lb-ft Pump shaft nut (balance disc nut) MSS-160 through MSS N-m 91 Lb-ft Pump support bracket anchor bolt 108 N-m 80 Lb-ft Stage split cone nut MSS-40 through MSS N-m 40 Lb-ft Stage split cone nut MSS-90 through MSS N-m 75 Lb-ft Stage split cone nut MSS-160 through MSS N-m 120 Lb-ft Stage split cone nut MSS N-m 150 Lb-ft Pump Alignment Specifications Motor Adapter Gap Tolerances for non-uniform gaps Good mm 0.015" Balance Disc Specifications Pump Model Original Thickness When New Wear Limit mm (0.020") MSS-15 through MSS mm (0.531") 13.0 mm (0.511") MSS-90 & MSS mm (0.630 ) 15.5 mm (0.610 ) MSS-160 through MSS mm (0.618 ) 15.2 mm (0.598 ) Lubricants and Compounds Lubricant Standard Glycerine or fresh water with soap ASTM D1257 Anti-seize compound Compliant with specific system

44 Notes

45 Visit our website for the latest version of this document and more information. Main Office Tel: Fax: FEDCO 800 Ternes Drive Monroe, MI 48162, USA Dubai Office Tel: Fax: Technopark, Plot TP10501 Jebel Ali South, PO Box 37603, Dubai, UAE Singapore Office Tel: Fax: Singapore Branch 82 Toh Guan Road East #C WaterHub Singapore, FEDCO Sales Office Service Center

MULTI-STAGE SEAWATER (MSS TM ) HIGH PRESSURE PUMPS Overhaul Manual

MULTI-STAGE SEAWATER (MSS TM ) HIGH PRESSURE PUMPS Overhaul Manual MULTI-STAGE SEAWATER (MSS TM ) HIGH PRESSURE PUMPS Overhaul Manual For Desalination Reverse Osmosis Service Models: MSS-90 MSS-120 MSS-160 MSS-200 MSS-240 Main Office Tel: 734-241-3935 Fax: 734-241-5173

More information

MSS MULTI-STAGE SEAWATER HIGH PRESSURE PUMPS

MSS MULTI-STAGE SEAWATER HIGH PRESSURE PUMPS INSTALLATION & OPERATION MANUAL English Version MSS MULTI-STAGE SEAWATER HIGH PRESSURE PUMPS Models: MSS-15 MSS-20 MSS-30 MSS-40 MSS-50 MSS-55 MSS-55 MSS-70 MSS-75 MSS-90 MSS-120 MSS-160 MSS-200 MSS-240

More information

MSS Pumps for Seawater Reverse Osmosis Installation, Operation & Maintenance Manual

MSS Pumps for Seawater Reverse Osmosis Installation, Operation & Maintenance Manual MSS Pumps for Seawater Reverse Osmosis Installation, Operation & Maintenance Manual Models MSS-15 MSS-20 MSS-30 MSS-50 MSS-70 Copyright 2009 Fluid Equipment Development Company Version MSS 2.0 Last revised:

More information

PRODUCT SERVICE MANUAL FOR BK12DHZ PUMPS

PRODUCT SERVICE MANUAL FOR BK12DHZ PUMPS PRODUCT SERVICE MANUAL FOR BK12DHZ PUMPS WARNING This manual, and the GENERAL INSTRUCTION MANUAL SRM00046, should be read thoroughly prior to pump installation, operation or maintenance. Manual No. SRM00095

More information

PRODUCT SERVICE MANUAL. BK6DHZ(C)-250, 275, 312 and 400 PUMPS

PRODUCT SERVICE MANUAL. BK6DHZ(C)-250, 275, 312 and 400 PUMPS PRODUCT SERVICE MANUAL BK6DHZ(C)-250, 275, 312 and 400 PUMPS WARNING This manual, and the GENERAL INSTRUCTION MANUAL, SRM00046, should be read thoroughly prior to pump installation, operation or maintenance.

More information

INSTRUCTION MANUAL AND PARTS LIST FOR. (A)E3LB(C)(K)-187, -200, and -250 SERIES PUMPS

INSTRUCTION MANUAL AND PARTS LIST FOR. (A)E3LB(C)(K)-187, -200, and -250 SERIES PUMPS INSTRUCTION MANUAL AND PARTS LIST FOR (A)E3LB(C)(K)-187, -200, and -250 SERIES PUMPS WARNING This Manual and GENERAL INSTRUCTIONS MANUAL, SRM00046, should be read thoroughly prior to pump installation,

More information

Instruction Manual and Parts List (G323FHF 630M) with Flow Serve Type Q Seal

Instruction Manual and Parts List (G323FHF 630M) with Flow Serve Type Q Seal TM Instruction Manual and Parts List (G323FHF 630M) with Flow Serve Type Q Seal WARNING This Instruction Manual and General Instructions Manual, CA-1, should be read thoroughly prior to pump installation,

More information

INSTRUCTION MANUAL AND PARTS LIST FOR PG/RG3D-275 SERIES PUMPS (Idler Cup and Hydrostatic Thrust Designs)

INSTRUCTION MANUAL AND PARTS LIST FOR PG/RG3D-275 SERIES PUMPS (Idler Cup and Hydrostatic Thrust Designs) TM INSTRUCTION MANUAL AND PARTS LIST FOR PG/RG3D-275 SERIES PUMPS (Idler Cup and Hydrostatic Thrust Designs) WARNING This Instruction Manual and General Instructions Manual, CA-1, should be read thoroughly

More information

Instruction Manual & Parts List For H/G323FXFSX-500_ & 800_ Pumps With Flowserve Type BX Cartridge Seal

Instruction Manual & Parts List For H/G323FXFSX-500_ & 800_ Pumps With Flowserve Type BX Cartridge Seal TM Instruction Manual & Parts List For H/G323FXFSX-500_ & 800_ Pumps With Flowserve Type BX Cartridge Seal WARNING This Special Instruction Manual and General Instructions Manual, CA-1, should be read

More information

Model DFR 070/156/220 Rotary Actuator

Model DFR 070/156/220 Rotary Actuator Figure 1 DFR 156 TABLE OF CONTENTS General 2 Actuator Assembly 18 Scope 2 Bushing / Yoke Assembly 18 Principles of Operation 2 Spring Barrel Assembly 18 Safety Caution 2 Diaphragm Plate Assembly 20 Specifications

More information

PRODUCT SERVICE MANUAL

PRODUCT SERVICE MANUAL PRODUCT SERVICE MANUAL FOR AM322ICX-325AE, 350AN and 400A PUMPS WARNING This Special Instruction Manual and General Instructions Manual, SRM00046, should be read thoroughly prior to pump installation,

More information

IMPORTANT SAFETY NOTICE

IMPORTANT SAFETY NOTICE IMPORTANT SAFETY NOTICE To: Our Valued Customers User safety is a major focus in the design of our products. Following the precautions outlined in this manual will minimize your risk of injury. ITT Goulds

More information

INSTRUCTION MANUAL AND PARTS LIST FOR PG/RG3D_-187, 218, 250 and 312 SERIES PUMPS

INSTRUCTION MANUAL AND PARTS LIST FOR PG/RG3D_-187, 218, 250 and 312 SERIES PUMPS INSTRUCTION MANUAL AND PARTS LIST FOR PG/RG3D_-187, 218, 250 and 312 SERIES PUMPS WARNING This Instruction Manual and General Instructions Manual, CA-1, should be read thoroughly prior to pump installation,

More information

GT SERIES WET PRIME PUMPS SERVICE MANUAL

GT SERIES WET PRIME PUMPS SERVICE MANUAL SERVICE MANUAL BEFORE GETTING STARTED This manual is intended as a guide to disassembly and reassembly of a Pioneer Pump. It is to be used only by trained and experienced service technicians who are familiar

More information

SERIES G3DB/AG3DB ELEVATOR

SERIES G3DB/AG3DB ELEVATOR TM INSTRUCTIONS AND PARTS LIST SERIES G3DB/AG3DB ELEVATOR WARNING This manual, and GENERAL INSTRUCTIONS MANUAL, CA-1, should be read thoroughly prior to pump installation, operation or maintenance. SRM00059

More information

Maintenance Information

Maintenance Information 80234313 Edition 2 May 2014 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the

More information

K12DHZ-312P Pump PRODUCT SERVICE MANUAL. Imo Part Number / BOM # 3220/523

K12DHZ-312P Pump PRODUCT SERVICE MANUAL. Imo Part Number / BOM # 3220/523 K12DHZ-312P Pump PRODUCT SERVICE MANUAL Imo Part Number / BOM # 3220/523 WARNING This manual and the General Installation, Operation, Maintenance and Troubleshooting Manual (SRM00046) should be read in

More information

SERIES PC INSTRUCTION AND OPERATION MANUAL

SERIES PC INSTRUCTION AND OPERATION MANUAL MEGGA SERIES PC INSTRUCTION AND OPERATION MANUAL Models PCT and PCF Close-coupled and frame-mounted single-stage horizontal end-suction pumps. WARNING: Read this manual before installing or operating this

More information

Product Service Manual For DLH12DHT SERIES PUMPS

Product Service Manual For DLH12DHT SERIES PUMPS Product Service Manual For DLH12DHT SERIES PUMPS Pump Size Bill of Material Assembly Drawing 275 3217 / 568 - DLH12DHTX-275 Figure 3 312 3220 / 561 - DLH12DHT 312 Figure 3 3220 / 567 - DLH12DHT - 312 P

More information

Maintenance Information

Maintenance Information 04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,

More information

Instruction Manual and Parts List For G/H323F 550/550J/550M Pumps with Crane Type 2, 8-1, FS QWD and FS Q Non-Cartridge Seals

Instruction Manual and Parts List For G/H323F 550/550J/550M Pumps with Crane Type 2, 8-1, FS QWD and FS Q Non-Cartridge Seals TM Instruction Manual and Parts List For G/H323F 550/550J/550M Pumps with Crane Type 2, 8-1, FS QWD and FS Q Non-Cartridge Seals WARNING This Instruction Manual and General Instructions Manual, CA-1, should

More information

INSTRUCTION MANUAL AND PARTS LIST FOR 3SIC AND 4SIC SERIES PUMPS

INSTRUCTION MANUAL AND PARTS LIST FOR 3SIC AND 4SIC SERIES PUMPS TM INSTRUCTION MANUAL AND PARTS LIST FOR 3SIC AND 4SIC SERIES PUMPS WARNING This manual, and General Instructions Manual, CA-1 should be read thoroughly prior to pump installation, operation or maintenance.

More information

PRODUCT SERVICE MANUAL FOR _G3D -350 and 400 SERIES PUMPS (Idler Cup and Hydrostatic Thrust Designs)

PRODUCT SERVICE MANUAL FOR _G3D -350 and 400 SERIES PUMPS (Idler Cup and Hydrostatic Thrust Designs) PRODUCT SERVICE MANUAL FOR _G3D -350 and 400 SERIES PUMPS (Idler Cup and Hydrostatic Thrust Designs) WARNING The Imo General Installation Operation, Maintenance, and Troubleshooting Manual, (No. SRM00046),

More information

PRODUCT OBSOLETED 1Q16

PRODUCT OBSOLETED 1Q16 TECHNICAL SERVICE MANUAL INDUSTRIAL ROTARY LOBE PUMP HIGH PRESSURE MODELS RL0167, 40167, 0257, 40257 SECTION PAGE ISSUE TSM270.2 1 B CONTENTS Introduction 1 Safety Information 1 Exploded Parts View 2 Torque

More information

CFHN SERIES PRODUCT SERVICE MANUAL

CFHN SERIES PRODUCT SERVICE MANUAL CFHN SERIES PRODUCT SERVICE MANUAL Metric standards apply for all pumps covered by this manual with regard to Mounting dimensions, external connections, bolts, bolt threads, plugs and bearings. WARNING

More information

Maintenance Information

Maintenance Information 80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS

GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS WITH HYDRAULIC CONTROL PACKAGE PART NUMBER: SE-023 REVISION:

More information

Installation, Operation, and Maintenance Manual

Installation, Operation, and Maintenance Manual Industrial Process Installation, Operation, and Maintenance Manual Cam-Tite Ball Valve Table of Contents Table of Contents Introduction and Safety...2 Safety message levels...2 User health and safety...2

More information

INSTRUCTION MANUAL AND PARTS LIST FOR SERIES 8L-630J AND 630M WARNING

INSTRUCTION MANUAL AND PARTS LIST FOR SERIES 8L-630J AND 630M WARNING INSTRUCTION MANUAL AND PARTS LIST FOR SERIES 8L-630J AND 630M WARNING READ CA-l AND TIDS INSTRUCTION MANUAL PRIOR TO INSTALLATION, OPERATION OR MAINTENANCE WARNING This Instruction Manual and General Instructions

More information

INSTRUCTION AND REPAIR MANUAL MODELS 341A, 342A AND 344A 6

INSTRUCTION AND REPAIR MANUAL MODELS 341A, 342A AND 344A 6 SECTION 6 ITEM 0 DATED JUNE 1998 SUPERSEDES ITEMS 1, 2, DATED MARCH 1992 INSTRUCTION AND REPAIR MANUAL MODELS 1A, 2A AND A 6 NOTE This repair manual is applicable to pump Models 1A, 2A and A. All photos

More information

ICV & ICVA Flanged Injection Control Valves 2 (DN 50) Type Installation, Maintenance and Operating Instructions

ICV & ICVA Flanged Injection Control Valves 2 (DN 50) Type Installation, Maintenance and Operating Instructions ICV & ICVA Flanged Injection Control Valves 2 (DN 50) Type 1500 Installation, Maintenance and Operating Instructions IMO-282 EN 11/2017 2 IMO-282 EN TABLE OF CONTENTS 1. GENERAL... 2. INSTALLATION... 2.1

More information

Tool-less Hinged Closure Installation, Operation, & Maintenance

Tool-less Hinged Closure Installation, Operation, & Maintenance 2612 Howard Street Louisville, KY 40211 USA Phone 502-774-6011 Fax 502-774-6300 Website: www.tubeturns.com For genuine Tube Turns Closure parts please contact factory: ttaftermarket@sypris.com Bulletin

More information

OWNER S MANUAL EVOLUTION 3500, 4500, 5500, & 8500 SERIES PUMPS

OWNER S MANUAL EVOLUTION 3500, 4500, 5500, & 8500 SERIES PUMPS OWNER S MANUAL EVOLUTION 3500, 4500, 5500, & 8500 SERIES PUMPS IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including

More information

7350 Series Power Transfer

7350 Series Power Transfer 750 Series Power Transfer Installation, Maintenance and Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box 0 975 Cottonwood Ave. TEL: -800-97-8664 TEL: 6-67-7600 Hartland, WI 509-000

More information

COYOTE ENTERPRISES, INC. 9/10 BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL

COYOTE ENTERPRISES, INC. 9/10 BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL COYOTE ENTERPRISES, INC. 9/10 BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL Parts & Machinery for the Abrasive Blast Industry 27301 East 121st Street Coweta, Oklahoma 74429 (918) 486-8411 Fax (918) 486-8412

More information

WMTA6 LN SERIES SEAL-LESS MAG-DRIVE MULTI-STAGE TURBINE PUMPS

WMTA6 LN SERIES SEAL-LESS MAG-DRIVE MULTI-STAGE TURBINE PUMPS WMTA6 LN SERIES SEAL-LESS MAG-DRIVE MULTI-STAGE TURBINE PUMPS INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS TO OBTAIN THE BEST PERFORMANCE FROM YOUR WARRENDER WMTA6 LN PUMP, PLEASE READ THIS MANUAL

More information

SAFETY MANUAL READ FIRST!

SAFETY MANUAL READ FIRST! 966-05-XX SAFETY MANUAL READ FIRST! IMPORTANT: READ THESE WARNINGS AND SAFETY PRECAUTIONS PRIOR TO INSTALLATION OR OPER- ATION. FAILURE TO COMPLY WITH THESE INSTRUC- TIONS COULD RESULT IN PERSONAL INJURY

More information

This manual presents installation, servicing, troubleshooting, and maintenance for M PUMPS CM MAG-M SERIES Information that may be required regarding

This manual presents installation, servicing, troubleshooting, and maintenance for M PUMPS CM MAG-M SERIES Information that may be required regarding Installation, Operating, Maintenance & Safety Instruction for M PUMPS CM MAG-M SERIES Centrifugal light Mag-Drive pumps (CM MAG-M06/1/2/3/4) This manual presents installation, servicing, troubleshooting,

More information

Model DF233 Control Valve

Model DF233 Control Valve Figure 1 DF233 Control Valve TABLE OF CONTENTS Introduction 2 Body and Packing Reassembly 7 Specifications 3 Fail Closed Actuator Reassembly 8 Valve Sizes 3 Fail Open Actuator Reassembly 9 Unpacking 4

More information

End Suction Centrifugal

End Suction Centrifugal M o d e l s 3 U / 3 U B End Suction Centrifugal Operating Instructions, Installation & Maintenance Manual Certified to NSF/ANSI 6, ANNEX G * NSF/ANSI 6 Annex G listed models: 3U EBARA International Corporation

More information

GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS

GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS -S INDICATES CYLINDERS ARE IN TANDEM PART NUMBER: 100121 REVISION "A" ECN

More information

CP-1, CP-2, CP-2L & CPD-2 Series Overhaul

CP-1, CP-2, CP-2L & CPD-2 Series Overhaul Replacement of Mechanical Seals for CM, CMU, CS and CSU Series Pumps Installation Instructions Form No. F-1031 Section 5013 Issue Date 03/01/85 Rev. Date 02/08/11 CP-1, CP-2, CP-2L & CPD-2 Series Overhaul

More information

Product Service Manual For AA3G Series Pumps Size 187 Through 250

Product Service Manual For AA3G Series Pumps Size 187 Through 250 Product Service Manual For AA3G Series Pumps Size 187 Through 250 WARNING The IMO General Installation Operation, Maintenance and Troubleshooting Manual, (No. SRM00046), this manual, and associated component

More information

1/2" AIR DRIVEN DIAPHRAGM PUMP

1/2 AIR DRIVEN DIAPHRAGM PUMP 1/2" DRIVEN DIAPHRAGM PUMP OPERATION AND SERVICE GUIDE O-1225D NOV. 2008 Page 1 of 6 Refer to Bulletin P-605, Parts List P-9151 DRIVEN, DOUBLE DIAPHRAGM PUMP MANUAL Congratulations on purchasing one of

More information

PRODUCT SERVICE MANUAL For G6D-187, 218, 250, 275 and 312 PUMPS

PRODUCT SERVICE MANUAL For G6D-187, 218, 250, 275 and 312 PUMPS PRODUCT SERVICE MANUAL For G6D-187, 218, 250, 5 and 312 PUMPS WARNING This Instruction Manual and General Instructions Manual, SRM00046, should be read thoroughly prior to pump service, installation, operation

More information

PRODUCT SERVICE MANUAL SERIES 4U AND 6U SERIES 4T AND 6T ROTOR SIZES

PRODUCT SERVICE MANUAL SERIES 4U AND 6U SERIES 4T AND 6T ROTOR SIZES PRODUCT SERVICE MANUAL SERIES 4U AND 6U SERIES 4T AND 6T ROTOR SIZES 118-250 WARNING The IMO General Installation Operation, Maintenance and Troubleshooting Manual, (No. SRM00046), this manual, and associated

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS OWNER S MANUAL FLO-MASTER XP2 SERIES PUMPS IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:

More information

INSTALLATION & OPERATING INSTRUCTIONS

INSTALLATION & OPERATING INSTRUCTIONS INSTALLATION & OPERATING INSTRUCTIONS WARNING RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND-FAULT CIRCUIT-INTERRUPTER. THE UNIT SHOULD BE INSTALLED BY A QUALIFIED SERVICE REPRESENTATIVE.

More information

Impeller Replacement

Impeller Replacement Impeller Replacement Threaded Shaft Frame Mount H 806 Clockwise Rotation Volute shown. 1149 0794 1 Unfasten hardware holding volute to bracket. Remove volute to expose impeller. Peel off old volute gasket

More information

Railroad Ball Valves Series 5REB3

Railroad Ball Valves Series 5REB3 Railroad Ball Valves Series 5REB3 4" (DN 00) Installation, Maintenance and Operating Instructions IMO-R4 /05 IMO-R4 Table of Contents GENERAL.................................... 3. Scope of the Manual........................

More information

TECHNICAL SERVICE MANUAL

TECHNICAL SERVICE MANUAL Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL HEAVY-DUTY Stainless steel BRACKET MOUNTED PUMPS SERIES 127 AND 4127

More information

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Type 3535 Three-way Valve with bellows seal and rod-type yoke (partial view) Mounting and Operating Instructions EB 8135/8136 EN Edition

More information

Installation and Operation Manual

Installation and Operation Manual Industrial Process Installation and Operation Manual Advantage Actuator 2.0 Table of Contents Table of Contents Introduction and Safety...2 Safety message levels...2 User health and safety...2 Transportation

More information

Maintenance Information

Maintenance Information 16573347 Edition 2 February 2014 Air Grinder Series 88H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

FOR FUTURE REFERENCE SERIES 93HPS

FOR FUTURE REFERENCE SERIES 93HPS Hypro Series 93HPS Hydraulically Driven Wetseal Multistage Pumps Repair Manual KEEP FOR FUTURE REFERENCE Form L-1578R Rev. A SERIES 93HPS Hydraulically Driven Stainless Steel Multistage Centrifugal Pumps

More information

INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS:

INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS: INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS: G-H, G-HL, G-K, G-KK, G-L, G-LQ, G-LL, GLS, G-Q, G-QS 1 Contents Maintenance Thrust bearing adjustment

More information

BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS

BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS PART NUMBER: 102264 REVISION: "C" DATE: November 2000 Page 1 of 11 1.0 INTRODUCTION 1.1

More information

SERVICE GUIDE 8540-B 8549-B C. High-Pressure Lubricant Pump DESCRIPTION. Pump Assembly. Specifications

SERVICE GUIDE 8540-B 8549-B C. High-Pressure Lubricant Pump DESCRIPTION. Pump Assembly. Specifications SERVICE GUIDE 8540-B 8549-B1 8549-C DESCRIPTION The major components of the high-pressure pump models in this series consist of a(n): air-operated motor lubricant pressure controller (pressurtrol) double-acting

More information

Fisher 657 Diaphragm Actuator Sizes and 87

Fisher 657 Diaphragm Actuator Sizes and 87 Instruction Manual 657 Actuator (30-70 and 87) Fisher 657 Diaphragm Actuator Sizes 30 70 and 87 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Installation... 3 Mounting

More information

DeZURIK " BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT

DeZURIK  BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT DeZURIK 20 144" BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT Instruction D10373 April 2017 Instructions These instructions provide information about the 20 (250 F2 model only) and the 24-144 BAW

More information

CH-4 Series Fire Pumps Overhaul Instructions

CH-4 Series Fire Pumps Overhaul Instructions CH-4 Series Fire Pumps Overhaul Instructions Table of Contents Model CHK-4, Transmission Driven (The pump is turned by a K-Series Transmission mounted directly to the pump.) Introduction... 2 Ordering

More information

D/G-03 Maintenance. Shutdown Procedure During Freezing Temperatures. Daily. Periodically

D/G-03 Maintenance. Shutdown Procedure During Freezing Temperatures. Daily. Periodically D/G-03 Maintenance NOTE: The numbers in parentheses are the Ref. Nos. on the illustrations in the Parts Manual. Daily Check the oil level and the condition of the oil. The oil level should be 3/4 in. (20

More information

Sub Section Title Page No.

Sub Section Title Page No. Sub Section Title Page No. 1 Introduction 3 2 Routine Maintenance 3 3 Disassembly 4 3.1 Disassembly of Double Crank Design 4 3.2 Disassembly of Scotch Yoke Design 5 3.3 Disassembly of Actuator Cylinder

More information

TC20 Chain Driven Power Take-Off Overhaul Instructions

TC20 Chain Driven Power Take-Off Overhaul Instructions TC20 Chain Driven Power Take-Off Overhaul Instructions Table of Contents Section Page Introduction 4 Ordering Repair Parts 4 General Information 5 Special Tools 6 Disassembly See Page 2 Reassembly See

More information

DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION:

DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION: DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION: These instructions are provided to familiarize the user with the seal and its use. The instructions must be read carefully

More information

70 Series 8700 Coupler 2-pc Hub & Shaft Three Phase Brake Instructions IP43 & IP56 (NEMA 2 & 4) Housing

70 Series 8700 Coupler 2-pc Hub & Shaft Three Phase Brake Instructions IP43 & IP56 (NEMA 2 & 4) Housing Bulletin No. BK4775-3 (08/2016) 70 Series 8700 Coupler 2-pc Hub & Shaft Three Phase Brake Instructions IP43 & IP56 (NEMA 2 & 4) Housing Read carefully before attempting to assemble, install, operate or

More information

PRODUCT OBSOLETED 1Q16

PRODUCT OBSOLETED 1Q16 TECHNICAL SERVICE MANUAL HEAVY DUTY STEEL EXTERNAL MOUNTED PUMPS SERIES 123 AND 4123 SIZES H-LL SECTION TSM 151.1 PAGE 1 OF 13 ISSUE C CONTENTS Introduction 1 Special Information 2 Maintenance 3 Packed

More information

Installation Instructions

Installation Instructions Installation Instructions BW Seals RIS Seal Rubber in shear slurry seal Experience In Motion 1 Equipment Check 1.1 Follow plant safety regulations prior to equipment disassembly: lock out motor and valves.

More information

Model DF269 Control Valve

Model DF269 Control Valve Figure 1 DF269 Control Valve TABLE OF CONTENTS Introduction 2 Fail Open Actuator Disassembly 6 General 2 Body and Packing Reassembly 7 Scope 2 Fail Closed Actuator Resassembly 8 Specifications 3 Fail Open

More information

Sachs 48mm Closed Cartridge fork Service Manual

Sachs 48mm Closed Cartridge fork Service Manual Sachs 48mm Closed Cartridge fork Service Manual 1 Fork seal driver 2 Special soft jaws 3 Fork cap wrench 4 Rebound rod holding tool 5 Compression assembly holding tool 6 Retaining clip tool Special Tools

More information

CONTROL VALVES SINGLE PORTED CLASSES DL, DDL, DOS, DDOS

CONTROL VALVES SINGLE PORTED CLASSES DL, DDL, DOS, DDOS 12501 Telecom Drive, Tampa Florida 33637 Installation, Operation and Maintenance 10/1.5.1 Rev. 0 CONTROL VALVES SINGLE PORTED CLASSES DL, DDL, DOS, DDOS TABLE OF CONTENTS INSTALLATION...2 VALVE POSITION...2

More information

Fisher V250 Ball Valve

Fisher V250 Ball Valve Instruction Manual Fisher V250 Ball Valve Contents Introduction... 1 Scope of Manual... 1 Description... 1 Installation... 3 Maintenance... 6 Replacing the Follower Shaft Seal... 6 Replacing the Drive

More information

CONTENTS. VIKING PUMP, INC. A Unit of IDEX Corporation Cedar Falls, IA USA SECTION TSM 710.1

CONTENTS. VIKING PUMP, INC. A Unit of IDEX Corporation Cedar Falls, IA USA SECTION TSM 710.1 TECHNICAL SERVICE MANUAL industrial heavy duty motor speed pumps SERIES 4076 AND 4176 SIZES hle, ate and ale SECTION TSM 710.1 PAGE 1 of 8 ISSUE B CONTENTS Introduction....................... 1 Safety

More information

INSTALLATION/OPERATION/MAINTENANCE INSTRUCTIONS FOR ARCHON MODELS WD2010L, WD2010, WD2010H WASHDOWN STATIONS. ARCHON Industries, Inc.

INSTALLATION/OPERATION/MAINTENANCE INSTRUCTIONS FOR ARCHON MODELS WD2010L, WD2010, WD2010H WASHDOWN STATIONS. ARCHON Industries, Inc. ARCHON Industries, Inc. Washdown Stations Models WD2010L, WD2010, WD2010H Installation / Operation / Maintenance Instructions 1 This manual has been prepared as an aid and guide for personnel involved

More information

Keystone Series GR resilient seated butterfly valves GRW/GRL Installation and operation manual

Keystone Series GR resilient seated butterfly valves GRW/GRL Installation and operation manual Before installation these instructions must be fully read and understood Important Before valves are installed or used the following actions are recommended. 1. Valves/parts have to be inspected and thoroughly

More information

WARNING CAUTION. CAUTION Do not exceed 120 psig (8.3 bar) air-inlet pressure.

WARNING CAUTION. CAUTION Do not exceed 120 psig (8.3 bar) air-inlet pressure. 13966-100-BP SAFETY MANUAL READ FIRST! IMPORTANT: READ THESE WARNINGS AND SAFETY PRECAUTIONS PRIOR TO INSTALLATION OR OPER- ATION. FAILURE TO COMPLY WITH THESE INSTRUC- TIONS COULD RESULT IN PERSONAL INJURY

More information

CT/GT CONVERSION INSTRUCTIONS

CT/GT CONVERSION INSTRUCTIONS Your CT/GT conversion kit is provided with the components listed below. All other part numbers listed throughout this supplement directly correspond to the CT agitator manual and represent the existing

More information

3, 4 & 6 (DN 80, 100 & 150) CLASS 150 & 300 STANDARD BORE SERIES 7150, 730S & 7300 FLANGED BALL VALVES EQUIPPED WITH KEROTEST HANDLE ASSEMBLIES

3, 4 & 6 (DN 80, 100 & 150) CLASS 150 & 300 STANDARD BORE SERIES 7150, 730S & 7300 FLANGED BALL VALVES EQUIPPED WITH KEROTEST HANDLE ASSEMBLIES 3, 4 & 6 (DN 80, 100 & 150) CLASS 150 & 300 STANDARD BORE SERIES 7150, 730S & 7300 FLANGED BALL VALVES EQUIPPED WITH KEROTEST HANDLE ASSEMBLIES Installation, Maintenance and Operating Instructions IMO-261

More information

SECTION ZF FRONT AXLE

SECTION ZF FRONT AXLE 04-101.01/ 1 2011JA14 SECTION 04-101.01 6 3 5 1 2 9 1. Upper radius rod 2. Lower radius rod 3. Caliper 4. BRAKE Disk 5. Pneumatic connector 6. Hub 7. steering knuckle 8. Grease Fitting 9. Pneumatic connector

More information

Valtek Auxiliary Handwheels and Limit Stops

Valtek Auxiliary Handwheels and Limit Stops Valtek Auxiliary s and Limit Stops Table of Contents Page 1 General information 2 Installation 2 Side-mounted handwheels, size 25 and 50 (linear actuators) 3 Side-mounted handwheels, size 100 and 200 (linear

More information

Purging Air From Divider Block Lubrication Systems

Purging Air From Divider Block Lubrication Systems FROST ENGINEERING SERVICE Purging Air From Lubrication Systems A D I V I S I O N O F G E C S E Y S A L E S & S E R V I C E DESCRIPTION Divider block lubrication systems operate correctly only when all

More information

Installation and Parts Replacement Manual For No. 188D BIO-DISC Reducer

Installation and Parts Replacement Manual For No. 188D BIO-DISC Reducer Installation and Parts Replacement Manual For No. 88D BIO-DISC Reducer These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of printing.

More information

CSO / CP PUMPS Vertical Spindle Type Installation, Operation and Maintenance Manual

CSO / CP PUMPS Vertical Spindle Type Installation, Operation and Maintenance Manual CSO / CP PUMPS Vertical Spindle Type Installation, Operation and Maintenance Manual www.sameng.co.za (011) 823 4250 Proud Manufacturers of SAMCO Pumps Contents INTRODUCTION 3 LOCATION OF UNIT 3 INSTALLATION

More information

70 Series 8700 End Mount Three Phase Brake Instructions IP56 (NEMA 4) Housing

70 Series 8700 End Mount Three Phase Brake Instructions IP56 (NEMA 4) Housing Bulletin No. BK4773-3 (08/2016) 70 Series 8700 End Mount Three Phase Brake Instructions IP56 (NEMA 4) Housing Read carefully before attempting to assemble, install, operate or maintain the product described.

More information

Fisher 2052 Diaphragm Rotary Actuator

Fisher 2052 Diaphragm Rotary Actuator Instruction Manual 2052 Actuator Fisher 2052 Diaphragm Rotary Actuator Contents Introduction... 1 Scope of Manual... 1 Description... 1 Specifications... 4 Installation... 4 Actuator Mounting and Changing

More information

INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, Application: 08-NEWER FORD SUPER DUTY WARNING

INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, Application: 08-NEWER FORD SUPER DUTY WARNING INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, 76250 Application: 08-NEWER FORD SUPER DUTY Your safety, and the safety of others, is very important. To help you make informed

More information

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS Setting Innovative Standards M PUMPS SRL Via dell artigianato, 120 45015 Corbola (RO) Italia Tel. +39 0426 346304 Fax + 39 0426 349126 1 info@mpumps.it MAGNETIC DRIVE PUMPS Centrifugal, peripheral, mag-drive

More information

READ AND SAVE THESE INSTRUCTIONS. Centrifugal Downblast Exhaust Fan Belt Driven for Roof & Wall Mounting

READ AND SAVE THESE INSTRUCTIONS. Centrifugal Downblast Exhaust Fan Belt Driven for Roof & Wall Mounting READ AND SAVE THESE INSTRUCTIONS INSTALLATION, OPERATING INSTRUCTIONS & PARTS MANUAL Centrifugal Downblast Exhaust Fan Belt Driven for Roof & Wall Mounting Electrical wiring and connections should be done

More information

DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION:

DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION: DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION: These instructions are provided to familiarize the user with the seal and its use. The instructions must be read carefully

More information

MECHANICAL FUEL METER. FM-100 and FM-200 Series Owner s Manual

MECHANICAL FUEL METER. FM-100 and FM-200 Series Owner s Manual MECHANICAL FUEL METER FM-100 and FM-200 Series Owner s Manual To the owner Congratulations on receiving your GPI Mechanical Fuel Meter. We at GPI are pleased to provide you with a fuel meter designed to

More information

SECTION 4 - FUEL/LUBRICATION/COOLING

SECTION 4 - FUEL/LUBRICATION/COOLING For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 4 - FUEL/LUBRICATION/COOLING 4 TABLE OF CONTENTS Carburetor Specifications... 4-2 Carburetor Schematic... 4-2 Carburetor... 4-3 Cleaning

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM)

INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM) INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM) IOM-1088 03-16 Model 1088 Vacu-Gard Blanketing Valve ISO Registered Company SECTION I I. DESCRIPTION AND SCOPE The Model 1088 Vacu-Gard is a tank blanketing

More information

I-795/906. Series 795 and 906 Installation-Ready Knife Gate Valves WARNING INSTALLATION AND MAINTENANCE INSTRUCTIONS

I-795/906. Series 795 and 906 Installation-Ready Knife Gate Valves WARNING INSTALLATION AND MAINTENANCE INSTRUCTIONS INSTALLATION AND MAINTENANCE INSTRUCTIONS I-795/906 Series 795 and 906 Installation-Ready Knife Gate Valves HANDWHEEL OPERATOR PNEUMATIC OPERATOR HYDRAULIC OPERATOR WARNING Read and understand all instructions

More information

Installation Instructions

Installation Instructions Installation Instructions TM Interseal SLC Series Self contained single cartridge heavy duty slurry seal Experience In Motion 1 General Seal Installation Instructions The following instructions are designed

More information

70 Series 8700 End Mount Three Phase Brake Instructions IP43 (NEMA 2) Housing

70 Series 8700 End Mount Three Phase Brake Instructions IP43 (NEMA 2) Housing Bulletin No. BK4772S-3 (6/2017) 70 Series 8700 End Mount Three Phase Brake Instructions IP43 (NEMA 2) Housing Read carefully before attempting to assemble, install, operate or maintain the product described.

More information

Maintenance Information

Maintenance Information 16573370 Edition 2 February 2014 Air Grinder 99V Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

KP-C Series. Close Coupled End Suction Centrifugal Pumps. Installation, Operation and Maintenance

KP-C Series. Close Coupled End Suction Centrifugal Pumps. Installation, Operation and Maintenance KP-C Series Close Coupled End Suction Centrifugal Pumps Installation, Operation and Maintenance PUMP MODEL NOMENCLATURE KP - 8 x 6 x 16 - E C - AI - BCM Pump Series Suction Pipe Size (in) Discharge Pipe

More information

DESCRIPTION FUEL AND VACUUM PUMP REMOVE AND REPLACE FUEL PUMP-OVERHAUL 6B PONTIAC SHOP MANUAL. S. Install battery and connect cables.

DESCRIPTION FUEL AND VACUUM PUMP REMOVE AND REPLACE FUEL PUMP-OVERHAUL 6B PONTIAC SHOP MANUAL. S. Install battery and connect cables. 6B-74 1955 PONTIAC SHOP MANUAL DESCRIPTION FUEL AND VACUUM PUMP All models are equipped with a combination fueland double acting vacuum pump operated by an eccentric bolted to the front end of the engine

More information

Maintenance Manual MM Transfer Cases. MTC-4208X/XL/XP/XLEV, MTC-4210X/XL/XP/XLEV and MTC-4213X Series Revised 09-16

Maintenance Manual MM Transfer Cases. MTC-4208X/XL/XP/XLEV, MTC-4210X/XL/XP/XLEV and MTC-4213X Series Revised 09-16 Maintenance Manual MM-0861 Transfer Cases MTC-4208X/XL/XP/XLEV, MTC-4210X/XL/XP/XLEV and MTC-4213X Series Revised 09-16 Service Notes About This Manual This manual provides maintenance and service procedures

More information