Storm Series Ranger II

Transcription

1 Parts Catalog Issued: Mar 2, 2017 Storm Series Ranger II RWD Power Wheelchair

2 Parts Catalog Usage Guide The information contained in this document is subject to change without notice. This catalog contains service parts for. If you have any questions regarding this catalog, please contact one of our Customer Service Representatives. SYMBOL DEFINITION For Customer Service Support Call: For Faxed In Orders Call: or For Technical Service Call: Literature Can Be Found at: or Throughout this catalog you will notice letters to draw your attention to specific footnotes which are located at the bottom of the page or below specified charts. Examples: A,B,C etc. NOTE: NLA = Special Comments = General information pertaining to that specific page = No Longer Available HARDWARE MEASUREMENTS The measurements for the hardware will be listed as follows: Screws, Bolts Diameter X Thread Count/Pitch X Length Washers Inside Diameter X Outside Diameter X Thickness Spacers Inside Diameter X Outside Diameter X Length For your convenience, we have supplied an area for you to list your Invacare Representatives. Name Phone Numbers 2017 Invacare Corporation, Elyria, Ohio. Invacare, Yes, you can., the Medallion Design, and Storm Series are registered trademarks of Invacare Corporation; Ranger II is a trademark of Invacare Corporation; Tash is a registered trademark of Tash International Inc.; Therafin is a registered trademark of W/R/ Medical Electronics Co.; Bussman is a registered trademark of Cooper Industries; MIDI is a registered trademark of Littelfuse Inc.; and Dynamic is a registered trademark of Dynamic Controls Limited. 1

3 TABLE of CONTENTS Description Page Number Accessories - Headrest Extension (9110L) Accessories - Miscellaneous Accessories - Oxygen Holder Assembly Accessories - Power Wheelchair Tool Kit Arms, Adjustable Height, Removable, Non-Reclining (After 9/30/00) Arms, Adjustable Height, Removable, Non-Reclining (Before 10/1/00 and All Recliners) Arms, Fixed Height, Removable, Non-Reclining (After 9/30/00) Arms, Fixed Height, Removable, Non-Reclining (Before 10/1/00 and All Recliners) Back Canes and Attaching Hardware (After 9/30/00) Back Canes and Attaching Hardware (Before 10/1/00) Back, Recliner Assembly Battery Boxes and Trays Battery Charger and Harnesses Casters and Forks Crossbraces and Seat Extensions Electronics - COM12 and COM Electronics - MKIV Controller, Programmer and Attaching Hardware Electronics - MKIV Displays Electronics - MKIV Joystick Mounting Hardware and Joystick Accessories Electronics - MKIV Joystick Options Electronics - MKIV Joysticks RII, RX, A, A+, TCHJOY

4 TABLE of CONTENTS Description Page Number Electronics - MKIV Joysticks PS, PFS and PSR Electronics - MKIV Sip-N-Puff/ Digital Interface Electronics - MKIV Swivel Joystick Hardware Electronics - MKVI Mid-Line Swing Bracket Assembly Electronics - Quad Link Assembly (Before 4/07/06) Electronics - Quad Link Assembly (QL) (After 4/06/06) Electronics - Tash and Therafin Accessories Frame Finishes, Touch-Up Paints and Upholstery Colors... 5 Frames, Side and Hardware (After 9/30/00) Frames, Side and Hardware (Before 10/1/00) Front Riggings - Adjustable Angle Footplate Assembly, AT PW93, PW93E Front Riggings - Adjustable Heel Loops Front Riggings - Calf Pads and Attaching Hardware Front Riggings - Footrest and Legrest Accessories Front Riggings - Footrest Supports - P Front Riggings - Footrest Supports - P93E Front Riggings - Footrest Supports - P93M Front Riggings - Footrest Supports - P93ST Front Riggings - Footrest Supports - PW Front Riggings - Footrest Supports - PW93E Front Riggings - Footrest Supports - PW93ST

5 TABLE of CONTENTS Description Page Number Front Riggings - Legrest Release Handles and Ratchet Assembly Front Riggings - Legrest Supports - P904A Front Riggings - Legrest Supports - PAS4A/PAL4A Front Riggings - One Piece Wooden Footboard - (S1263) For P93, P93E, P93M, PW93, PW93E 96 Front Riggings - Pivot/ Slide Tube and Footplate - P904, PAL4A, PAS4A Front Riggings - Pivot/ Slide Tube and Footplate - P93, P93E, P93M Front Riggings - Pivot/ Slide Tube and Footplate - PW93, PW93E Front Riggings - Reference Chart Front Riggings- Pivot/ Slide Tube and Footplate - P93ST, PW93ST Motor, 2-Pole and Gearbox Motor, 4-Pole and Gearbox Packaging, Literature and Decals... 8 Solid Folding Seats Upholstery, Back Non-Recliner (After 9/30/00) Upholstery, Back Non-Recliner (Before 10/01/00) Upholstery, Recliner Back, Headrests and Pillows Upholstery, Seat Warranty Replacement Parts Wheel Lock Wheels, Rear and Anti-Tippers

6 Frame Finishes, Touch-Up Paints and Upholstery Colors Frame Finishes and Touch-Up Paints NOTE: Color Number Part Number Bottle Size Color 02P NLA.6 oz. Pink Pearl 06P NLA.6 oz. Super Teal 08P NLA.6 oz. Deep Purple 17P NLA.6 oz. Cobalt Blue 22P NLA.6 oz. Anthracite 24P NLA.6 oz. Wet Black 29P NLA.6 oz. White 30P NLA.6 oz. Sunny Yellow 31P NLA.6 oz. Lollipop Pink 33P NLA.6 oz. Red 34P NLA.6 oz. Flat Black 61P NLA Electric Red.6 oz. See Note(s) A See Note(s) A See Note(s) A 62P NLA Electric Blue.6 oz. See Note(s) A See Note(s) A See Note(s) A 64P NLA Metallic Blue.6 oz. See Note(s) A See Note(s) A See Note(s) A 65P NLA Metallic Green.6 oz. See Note(s) A See Note(s) A See Note(s) A 69P NLA.6 oz. Teflon Black 71P Silver Vein 80P NLA.6 oz. Evergreen with Navy 83P NLA.6 oz. Royal Blue with Grape 84P NLA.6 oz. Lavender 101P NLA.6 oz. Jeweled Green 102P NLA.6 oz. Denim Blue 103P NLA.6 oz. Mocha Frost 104P NLA.6 oz. Electric Teal 105P NLA.6 oz. Midnight Blue A - Veiling is not available on these colors. 5

7 Frame Finishes, Touch-Up Paints and Upholstery Colors Sparkle Frame Finishes Color Number 72P 73P 74P 75P 76P 88P Color Twilight Sparkle Gold Sparkle Green Sparkle Blue Sparkle Red Sparkle Wet Black with Twilight Sparkle Veil Options Color Number 13V 67V 19V 15V Color Dark Purple Veil Gold Veil Green Veil Grey Veil 6

8 Frame Finishes, Touch-Up Paints and Upholstery Colors Upholstery Colors Vinyl Colors U67 Black U75 Dove Grey U85 Dark Blue U86 Ruby U97 Sky Blue U88 Camel Nylon Colors U240 Black 7

9 Packaging, Literature and Decals NOTE: When adjusting or replacing parts, please refer to your Owner's Manual for assistance. 8

10 Packaging, Literature and Decals NOTE: When adjusting or replacing parts, please refer to your Owner's Manual for assistance. Item Number Note Part Number Description Quantity Per Package Assembly X148 Carton, Hardware NLA NLA - Carton, Battery Boxes NLA NLA - Insert NLA NLA - Carton Bag, Poly (72" L x 35" W x 19" D) X011 Carton, Front Riggings NLA NLA - Insert, Carton NLA NLA - Bag, Poly (26" L x 15" W) X039-NLA NLA - Insert, Carton Decal, Transportation NLA NLA - Plate, Name, Patent Numbers C NLA NLA - Decal, Invacare 3-D Logo (1-19/32" L) B,C NLA NLA - Decal, Model, Black - Ranger II C NLA NLA - Decal, Model, White - Ranger II NLA NLA - Decal S 1 2 A Operating Instructions, MKIV 1 1 A,D NLA NLA - Instruction Manual, MKIV RII 1 1 A NLA Owner's Manual 1 1 NOTE: A - Not Shown B - Used for chairs with frame colors 02P, 29P, 30P and 84P only. C - Invacare logo added and model decals changed 1/11/00. When replacing side frames before 1/11/00 order decals in pairs to match. D - Item is no longer available from the Invacare Service Parts Department. Refer to the Invacare Website under "Product Literature Search". Enter the part number in the "Keywords" field and download a free PDF version copy. 9

11 Side Frames and Hardware (Before 10/1/00) 10

12 Side Frames and Hardware (Before 10/1/00) Item #1 - Side Frames and Hardware NOTE: Frame Type Non-Recliner Recliner Adult - Right NLA NLA See Note(s) A, B See Note(s) A, B Adult - Left NLA NLA See Note(s) A, B See Note(s) A, B Hemi - Right NLA NLA See Note(s) B, A See Note(s) B, A Hemi - Left NLA NLA See Note(s) A, B See Note(s) A, B A - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - Decals not included with frame. See page titled "Packaging, Literature and Decals." Item Number Note Part Number Description Quantity Per Package Assembly 1 See Chart Item #1 - Side Frames and Hardware Kit, Lock Handle w/rivets (Pair) X074 Spring, Arm Lock Pin, Arm Lock, Black X006 Bearing (5/8") NLA NLA - Cap, End, Oval A NLA NLA - Screw, Socket Flat Head (#10-32 x 1-3/4") Clamp, Seat Screw, Socket Head (1/4-20 x 1-1/4") A NLA NLA - Screw, Socket Flat Head (#10-32 x 1-5/8") Hanger, Front Rigging, Black - Right Hanger, Front Rigging, Black - Left Plug Button, Black (3/4") Locknut (1/4-20) Locknut (#10-32) NLA NLA - Fastener, Panel Snap-In 1 1 NOTE: A - Screws changed 9/16/99 and serve as a direct replacement for chairs manufactured before 9/16/99. 11

13 Side Frames and Hardware (After 9/30/00) 12

14 Side Frames and Hardware (After 9/30/00) Item # 1 - Side Frames and Hardware NOTE: Frame Type Non-Recliner Recliner Adult - Right NLA NLA See Note(s) A, B See Note(s) B, A Adult - Left NLA See Note(s) B, A See Note(s) A, B Hemi - Right NLA See Note(s) A, B See Note(s) B, A Hemi - Left NLA See Note(s) B, A See Note(s) A, B A - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - Decals not included with frame. See page titled "Packaging, Literature and Decals." Item Number Note Part Number Description Quantity Per Package Assembly 1 A See Chart Item # 1 Side Frames and Hardware X006 Bearing (5/8") Pin, Arm Lock, Black X074 Spring, Arm Lock Rivet, Tubular Plug Button, Black (1") Kit, Lock Handle w/rivets (Pair) NLA NLA - Cap, End, Oval NLA NLA - Screw, Socket Flat Head (#10-32 x 1-3/4") Clamp, Seat NLA NLA - Screw, Socket Flat Head (#10-32 x 1-5/8") Screw, Socket Head (1/4-20 x 1-1/4") Hanger, Front Rigging, Black - Right Hanger, Front Rigging, Black - Left Plug Button, Black (3/4") Locknut (#10-32) Locknut (1/4-20) 1 2 NOTE: A - Includes items

15 Crossbraces and Seat Extensions 14

16 Crossbraces and Seat Extensions Item Number Note Part Number Description NOTE: Quantity Per Package Assembly See Chart Item #1 - Crossbraces NLA NLA - Cap, Hub, Black X001 Locknut (5/16-24) Washer, Caplugs (11/32" I.D. x 1" O.D.) NLA NLA - Plug, Pivot Tube Screw, Hex Head (5/16-24 x 4-1/4") NLA NLA - Screw, Hex Head (1/4-20 x 1-3/4") Plug Button, Black (1") Locknut (1/4-20) NLA NLA - Link, Pivot, Hemi, Black (14-15" W) NLA NLA - Link, Pivot, Hemi, Black (16-18" W) NLA NLA - Link, Pivot, Hemi, Black (19-20" W) NLA NLA - Link, Pivot, Adult, Black (14-15" W) Link, Pivot, Adult, Black (16-18" W) Link, Pivot, Adult, Black (19-20" W) Screw, Hex Head (1/4-20 x 1-1/2") NLA NLA - Strap, Pivot Link Screw, Hex Head (5/16-24 x 3-1/2") NLA NLA - Bushing (5/16 x 7/16 x 9/32") Washer, Nylon (5/16 x 7/8 x 1/8") Washer, Flat (5/16 x 5/8 x 1/16") Locknut (5/16-24) Spacer, Coved (3/4 x 1 x 1/2") X000 Washer, Flat (5/16 x 11/16 x 1/16") NLA NLA - Hardware, Crossbrace 1 1 See Chart Item #21 Seat Extension Kit (Pair) Screw w/ Washer (#10 x 7/8") X003 Screw, Phillips Pan Head (#10 X 5/8") Locknut (1/4-20) 1 1 A,B NLA NLA - Hardware, Crossbrace Pivot Tube 1 1 A - Includes Items 2-6 B - Not Shown 15

17 Crossbraces and Seat Extensions Item #1 - Crossbraces Crossbrace Type 14" Wide 16" Wide 18" Wide 20" Wide Hemi NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A See Note(s) A Adult NLA NLA NLA NLA See Note(s) A, B See Note(s) B, A See Note(s) B, A See Note(s) B, A NOTE: A - Decals are not included with Crossbraces. See page titled "Packaging, Literature and Decals." B - These Crossbraces are No Longer Available on Storm RII Series wheelchair. NOTE: When replacing crossbraces for chairs built before 6/18/99 using seat extensions, a new seat extension kit must be ordered. Item #21 Seat Extension Kit (Pair) Seat Extension Type (Pair) Includes Hardware 1" 2" NOTE: A - No Longer Available for the Storm Ranger II Series wheelchair Part Number NLA NLA See Note(s) A 16

18 Back Canes and Attaching Hardware (Before 10/1/00) 17

19 Back Canes and Attaching Hardware (Before 10/1/00) Item Number Note Part Number Description Quantity Per Package Assembly 1 See Chart #1 Back Cane Assemblies See Chart #2 Spreader Bar Package, Foam Hand Grip (9" L) Package, Plug Button, Black (7/8") A Kit, Back Cane Attaching Hardware Locknut (5/16-24) Locknut (1/4-20) Screw w/ Lug (5/16-24 x 1-3/8") Insert, Non-Threaded Back Cane 1 2 (For Back Heights 20" and Lower) 10 Screw, Hex Head (1/4-20 x 1-1/2") Washer (1/4 x 23/32 x 1/16") 1 4 NOTE: A - Includes Items

20 Back Canes and Attaching Hardware (Before 10/1/00) #1 Back Cane Assemblies Back Height Back Cane- No Push Handle 10 Deg. Bend Back Cane- Push Handle Straight 16" NLA " NLA " NLA " NLA " NLA NOTE: Back Cane Assemblies include Foam Grips and Plug Buttons where shown Back Cane- Push Handle 10 Deg. Bend NLA #2 Spreader Bar Chair Width 14" 16" 18" 20" Part Number NLA

21 Back Canes and Attaching Hardware (After 9/30/00) Item Number Note Part Number Description Quantity Per Package Assembly Back Cane Assembly, 10 Degree Bend NLA NLA - Back Cane Assembly, Straight Grip, Foam (8") NLA NLA - Tube, Rear Upright, Black Washer (1/4 x 1/2 x 1/16") Screw, Hex Head (1/4-20 x 1-1/4") NLA NLA - Insert, Threaded Screw, Hex Head (1/4-28 x 1-3/4") Washer (1/4 x 23/32 x 1/16") Locknut (1/4-28) Locknut (1/4-20) A NLA NLA - Hardware, Back Cane Attaching (Pair) 2 1 NOTE: A - Includes Items

22 Recliner Back Assembly 21

23 Recliner Back Assembly Item #3 - Back Cane with Grip Back Height 18" H 20" H 22" H 24" H 26" H 14" W Right NLA NLA NLA NLA NLA 14" W Left NLA NLA NLA NLA NLA 16" W Right " W Left " W Right " W Left

24 Item Number Note Part Number Description Recliner Back Assembly Quantity Per Package Assembly Plug Button, Black (7/8") NLA NLA - Headrest Tube Assembly, Black - Right NLA NLA - Headrest Tube Assembly, Black - Left See Chart Item #3 - Back Cane with Grip B,F Cable with Trigger B,G Cable with Trigger B,H Cable with Trigger Washer, Nylon (11/32 x 11/16 x 1/16") Screw, Shoulder Hex Socket Head (5/16 x 7/8", 1 2 1/4-20) 7 D Cylinder, Lock, Recline E Cylinder, Lock Pivot, Block Screw, Shoulder Hex Socket (3/8 x 1-1/4", 5/16-18) Bar, Spreader, Black (14-20" W) Spring, Torsion w/ Button Screw, Phillips Pan Head (#10-32 x 1-1/8") C NLA NLA - Screw, Phillips Pan Head (#10-24 x 1-1/4") Tie Wrap (5-5/8" L) Locknut (1/4-20) Washer (1/4 x 1/2 x 1/16") Locknut (5/16-18) Washer, Flat (5/16 x 5/8 x 1/16") A NLA NLA - Switch, Limit, Assembly NLA NLA - Washer, Internal Tooth Lock (#4-40) NLA NLA - Screw, Slotted Hex Washer Head Tap 1 5 (#4-3/8") Sensor, Actuator Switch NLA NLA - Clamp, Cable Tie Wrap (5-5/8" L) 1 1 NOTE: A - Includes Items B - When ordering cable assembly # or # for chairs made before 8/4/99 or # for chairs made before 2/1/00, item 12 # must be ordered as well. C - Lever fastener changed 8/4/99 from a "10-32 threaded insert" to a "10-24 tinnerman nut" for item 4 # and # and 2/1/00 for # D - Ranger II Basic - Standard 250 lb. maximum capacity. E - Ranger II Standard - Heavy Duty 300 lb. maximum capacity. F - 26" High Canes G " High Canes H - 18 and 20" High Canes 23

25 Non-Recliner Back Upholstery (Before 10/01/00) Single Liners NOTE: Chair Width 14" Wide 16" Wide 18" Wide Nylon 16-17" Height Nylon 18-20" Height Vinyl 16-17" Height See Note(s) A NLA See Note(s) A NLA See Note(s) A NLA Vinyl 18-20" Height See Note(s) A NLA See Note(s) A NLA See Note(s) A NLA See Note(s) A See Note(s) A A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." 24

26 Non-Recliner Back Upholstery (Before 10/01/00) Dual Liners NOTE: Chair Width 14" Wide 16" Wide 18" Wide 20" Wide Nylon 16-17" Height Nylon 18-20" Height Vinyl 16-17" Height See Note(s) A NLA See Note(s) A NLA See Note(s) A NLA See Note(s) A NLA Vinyl 18-20" Height See Note(s) A NLA See Note(s) A NLA See Note(s) A NLA See Note(s) A NLA See Note(s) A See Note(s) A A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." NOTE: Dual line back upholstery is used with chairs that have a seat deeper than 17" or back wider than 18." Back Upholstery Hardware Part Number Consists of: (2) each Screws with Washers (#10 x 7/8") and (2) each Cable Ties. 25

27 Upholstery, Back Non-Recliner (After 9/30/00) NOTE: Chair Width 14" Wide 16" Wide 18" Wide Nylon 16-20" Height Vinyl 16-20" Height NLA See Note(s) A NLA See Note(s) A " Wide See Note(s) A See Note(s) A A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." 26

28 Upholstery, Back Non-Recliner (After 9/30/00) Back Upholstery Hardware Part Number Consists of: (2) each Screws with Washers (#10 x 7/8") and (2) each Cable Ties. 27

29 Seat Upholstery NOTE: Nylon Seat Upholstery is No Longer Available for Storm Ranger II Series wheelchair. Vinyl NOTE: Chair Width 16" D 17" D 18" D 14" W NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A 16" W NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A 18" W NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A 20" W NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery." 28

30 Seat Upholstery NOTE: Nylon Seat Upholstery is No Longer Available for Storm Ranger II Series wheelchair. Seat Upholstery Hardware Part Number NLA Consists of: (8) each Screws with Washers (#10 x 7/8") 29

31 Recliner Back, Headrests and Pillow Upholstery Recliner Back Upholstery Nylon - Single Liners Chair Width 18" H 20" H 22" H 24" H 26" H 14" W NLA NLA NLA NLA NLA 16" W " W Recliner Back Upholstery Nylon - Dual Liners Chair Width 18" H 20" H 22" H 24" H 26" H 14" W NLA NLA NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A 16" W See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A 18" W See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A 20" W See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A NOTE: A - Dual liner back upholstery is used with chairs that have a seat deeper than 17" or back wider than 18." Headrest Nylon 14" W 16" W 18" W 20" W Pillows Nylon 14" W 16-18" W 20" W NLA 30

32 Recliner Back, Headrests and Pillow Upholstery Nylon Upholstery Hardware Back Upholstery Hardware Part Consists of: (10) each Screw with Washer (#10 x 7/8") Headrest Upholstery Hardware Part Consists of: (6) each Screw with Washer (#10 x 7/8") Recliner Back Upholstery Vinyl - Single Liners Chair Width 18" H 20" H 22" H 24" H 26" H 14" W NLA NLA NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A 16" W NLA NLA NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A 18" W NLA NLA NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A NOTE: A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery." Recliner Back Upholstery Vinyl - Dual Liners Chair Width 18" H 20" H 22" H 24" H 26" H 14" W NLA NLA NLA NLA NLA See Note(s) B, A See Note(s) B, A See Note(s) A, B See Note(s) B, A See Note(s) B, A 16" W NLA NLA NLA NLA NLA See Note(s) B, A See Note(s) B, A See Note(s) B, A See Note(s) B, A See Note(s) B, A 18" W NLA NLA NLA NLA NLA See Note(s) B, A See Note(s) B, A See Note(s) B, A See Note(s) B, A See Note(s) B, A 20" W NLA NLA NLA NLA NLA See Note(s) B, A See Note(s) B, A See Note(s) B, A See Note(s) B, A See Note(s) B, A NOTE: A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery." B - Dual liner back upholstery is used with chairs that have a seat deeper than 17" or back wider than 18." 31

33 NOTE: Recliner Back, Headrests and Pillow Upholstery Headrest Vinyl 14" W 16" W 18" W 20" W NLA NLA NLA See Note(s) A See Note(s) A See Note(s) A See Note(s) A A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery." Pillow Vinyl NOTE: 14" W 16-18" W 20" W NLA NLA See Note(s) A See Note(s) A See Note(s) A A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery." Vinyl Upholstery Hardware Back Upholstery Hardware Part consists of: (10) each Screw with Washer (#10 x 7/8") Headrest Upholstery Hardware Part consists of: (4) each Screw with Washer (#10 x 7/8") 32

34 Solid Folding Seats NOTE: Solid Folding Seats measure two inches narrower than actual seat width. 33

35 Solid Folding Seats NOTE: Solid Folding Seats measure two inches narrower than actual seat width. Item Number Note Part Number Description Quantity Per Package Assembly Washer (#10 Flat) Bracket, Seat, Chrome NLA NLA - Hook, Seat X008 Screw, Phillips Pan Head (#10-32 x 11/16") A Solid Folding Seat w/ Hardware, Vinyl (14" W x 16" 1 1 D) 5 A NL NLA - Solid Folding Seat w/ Hardware, Vinyl (16" W 1 1 A x 16" D) 5 A Solid Folding Seat w/ Hardware, Vinyl (18" W x 16" 1 1 D) 5 A Solid Folding Seat w/ Hardware, Nylon (20" W x 16" 1 1 D) 5 A Solid Folding Seat w/ Hardware, Nylon (20" W x 18" D) 1 1 NOTE: A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." 34

36 Adjustable Height, Removable Arms Non-Reclining (Before 10/1/00 and All Recliners) 35

37 Adjustable Height, Removable Arms Non-Reclining (Before 10/1/00 and All Recliners) Item Number Note Part Number Description Quantity Per Package Assembly 1 A Pad, Arm, Vinyl, Full Length - Right (14" L x 2" W) A Pad, Arm, Vinyl, Full Length - Left (14" L x 2" W) A Pad, Arm, Vinyl, Desk Length (9" L x 2" W) Package, Screw, Phillips Pan Head (#10-32 x /8") Arm Tube Assembly w/ Plug Buttons, Full Length, 1 1 Black - Right/Left Arm Tube Assembly w/ Plug Buttons, Desk Length, 1 1 Black - Right/Left Tube, Arm, Upper with Plug Buttons, Chrome, Full 1 1 Length Tube, Arm, Upper with Plug Buttons, Black, Desk 1 1 Length Plug Button, Black (7/8") B,C Arm Base, Adjustable Height, Color - Right B,C Arm Base, Adjustable Height, Color - Left C NLA NLA - Arm Base, Adjustable Height, Chrome - Right C NLA NLA - Arm Base, Adjustable Height, Chrome - Left Kit, Lock Handle w/rivets (Pair) X074 Spring, Arm Lock Pin, Arm Lock, Black C Guard, Clothing Rivet 1 6 NOTE: A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." C - Stainless steel clothing guards were replaced with ABS plastic. Chairs manufactured before 7/30/97 should be ordered in pairs. 36

38 Adjustable Height Removable Arms Non-Reclining (After 9/30/00) 37

39 Adjustable Height Removable Arms Non-Reclining (After 9/30/00) Item Number Note Part Number Description Quantity Per Package Assembly 1 A Pad, Arm, Vinyl, Full Length - Right (14" L x 2" W) A Pad, Arm, Vinyl, Full Length - Left (14" L x 2" W) B,F Kit, Arm Pad w/ Screws, Full Length, Urethane 1 1 Waterfall, Black (13" L x 2-5/8" W) Kit, Arm Pad w/ Screws, Full Length, Urethane 2 1 Waterfall, Black (13" L x 2-5/8" W) (Pair) 1 A Pad, Arm, Vinyl, Desk Length (9" L x 2" W) B,F Kit, Arm Pad w/ Screws, Desk Length, Urethane 1 1 Waterfall, Black (9" L x 2-5/8" W) Kit, Arm Pad w/ Screws, Desk Length, Urethane 2 1 Waterfall, Black (9" L x 2-5/8" W) (Pair) Package, Screw, Phillips Pan Head (#10-32 x /8") 2 E Package, Screw, Phillips Pan Head (#10-32 x /4") Arm Tube Assembly w/ Plug Buttons, Full Length, 1 1 Black - Right/Left Arm Tube Assembly w/ Plug Buttons, Desk Length, 1 1 Black - Right/Left Plug Button, Black (7/8") Plug, Pivot X074 Spring, Arm Lock Pin, Arm Lock, Black Kit, Lock Handle w/rivets (Pair) Plug Button, Black (5/8") Rivet Guard, Clothing C NL NLA - Arm Base, Adjustable Height, Color - Right 1 1 A 12 C NL NLA - Arm Base, Adjustable Height, Color - Left 1 1 A Pin, Pull Screw, Socket Button Head (1/4-20 x 1-5/8") Clevis, Pivot Locknut (1/4-20) D Hardware, Mounting, Swingaway Armrest 1 1 NOTE: A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - As of 1/3/02 upholstered waterfall armpads were replaced with black urethane waterfall armpads. Order in pairs with screws for chairs manufactured before1/3/02. C - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." D - Includes items E - For urethane waterfall armpads only F - After 7/9/07 Invacare recommends ordering armpads in pairs to assure uniform appearance on chair 38

40 Fixed Height, Removable Arms Non-Reclining (Before 10/1/00 and All Recliners) 39

41 Fixed Height, Removable Arms Non-Reclining (Before 10/1/00 and All Recliners) Item Number Note Part Number Description 1 A 1 A 1 A 2 3 B 3 B 3 C 3 C B 3 B 3 C 3 C B 6 B 6 C 6 C B 6 B 6 C 6 C 6 6 Quantity Per Package Assembly Pad, Arm, Vinyl, Full Length - Right (14" L x 2" W) Pad, Arm, Vinyl, Full Length - Left (14" L x 2" W) Pad, Arm, Vinyl, Desk Length (9" L x 2" W) Package, Screw, Phillips Pan Head (#10-32 x /8") Desk Length Arm Tube (Color), Right Tube, Arm, Desk Length, Color - Left NLA NLA - Tube, Arm, Desk Length, Chrome - Right NLA NLA - Tube, Arm, Desk Length, Chrome - Left NLA NLA - Tube, Arm, Desk Length, Black - Right NLA NLA - Tube, Arm, Desk Length, Black - Left NL NLA - Tube, Arm, Full Length, Color - Right 1 1 A NL NLA - Tube, Arm, Full Length, Color - Left 1 1 A NLA NLA - Tube, Arm, Full Length, Chrome - Right NLA NLA - Tube, Arm, Full Length, Chrome - Left NLA NLA - Tube, Arm, Full Length, Standard, Black Right NLA NLA - Tube, Arm, Full Length, Standard, Black - Left NLA NLA - Guard, Clothing, Desk Length NLA NLA - Guard, Clothing, Full Length (16-19" D) Screw, Phillips Pan Head Tap (#8-32 x 3/8") NL NLA - Arm Assembly, Desk Length, Color - Right 1 1 A NL NLA - Arm Assembly, Desk Length, Color - Left 1 1 A NLA NLA - Arm, Desk Length without Armpad, Chrome Right NLA NLA - Arm, Desk Length without Armpad, Chrome Left NLA NLA - Arm Assembly, Desk Length, Chrome - Right NLA NLA - Arm Assembly, Desk Length, Chrome - Left NL NLA - Arm, Full Length without Armpad, Color A Right NL NLA - Arm, Full Length without Armpad, Color - Left 1 1 A NLA NLA - Arm, Full Length without Armpad, Chrome Right NLA NLA - Arm, Full Length without Armpad (Chrome), 1 1 Left NLA NLA - Arm Assembly, Full Length, Black - Right 1 1 (Standard) (16-19" D) NLA NLA - Arm Assembly, Full Length, Black - Left 1 1 (Standard) (16-19" D) 40

42 NOTE: Fixed Height, Removable Arms Non-Reclining (Before 10/1/00 and All Recliners) A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." C - Chome is NLA as of 3/22/99. Black replaced chrome. Order arm components in pairs to match. 41

43 Fixed Height Removable Arms Non-Reclining (After 9/30/00) 42

44 Item Number Note Part Number Description 1 A 1 A 1 C,E 1 1 A 1 C,E B 3 B 3 B 3 B B 8 B 8 B 8 B D 14 Fixed Height Removable Arms Non-Reclining (After 9/30/00) Quantity Per Package Assembly Pad, Arm, Vinyl, Full Length - Right (14" L x 2" W) Pad, Arm, Vinyl, Full Length - Left (14" L x 2" W) Kit, Arm Pad w/ Screws, Full Length, Urethane 1 1 Waterfall, Black (13" L x 2-5/8" W) Kit, Arm Pad w/ Screws, Full Length, Urethane 2 1 Waterfall, Black (13" L x 2-5/8" W) (Pair) Pad, Arm, Vinyl, Desk Length (9" L x 2" W) Kit, Arm Pad w/ Screws, Desk Length, Urethane 1 1 Waterfall, Black (9" L x 2-5/8" W) Kit, Arm Pad w/ Screws, Desk Length, Urethane 2 1 Waterfall, Black (9" L x 2-5/8" W) (Pair) Package, Screw, Phillips Pan Head (#10-32 x /8") Package, Screw, Phillips Pan Head (#10-32 x /4") NL NLA - Tube, Arm, Full Length, Color - Right 1 1 A NL NLA - Tube, Arm, Full Length, Color - Left 1 1 A NL NLA - Tube, Arm, Desk Length, Color - Right 1 1 A NL NLA - Tube, Arm, Desk Length, Color - Left 1 1 A Plug Button, Black (5/8") Screw, Phillips Pan Head Tap (#8-32 x 3/8") NLA NLA - Guard, Clothing, Desk Length Plug, Pivot NL NLA - Arm Assembly, Full Length, Color - Right 1 1 A NL NLA - Arm Assembly, Full Length, Color - Left 1 1 A NL NLA - Arm Assembly, Desk Length, Color - Right 1 1 A NL NLA - Arm Assembly, Desk Length, Color - Left 1 1 A Pin, Pull Screw, Socket Button Head (1/4-20 x 1-5/8") Clevis, Pivot Locknut (1/4-20) Hardware, Mounting, Swingaway Armrest Plug Button, Black (7/8")

45 NOTE: Fixed Height Removable Arms Non-Reclining (After 9/30/00) A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." C - As of 1/3/02 upholstered waterfall armpads were replaced with black urethane waterfall armpads. Order in pairs with screws for chairs manufactured before 1/3/02. D - Includes Items E - After 7/9/07 Invacare recommends ordering armpads in pairs to assure uniform appearance on chair 44

46 Casters and Forks 45

47 Item Number Note Part Number Description Casters and Forks Quantity Per Package Assembly Plug Button, Head Tube, Black Locknut (5/8-18) Washer, Nylon (5/8 x 1-5/16 x 1/8") Locknut (7/16-20) Fork and Stem (8" Caster) A Fork, Caster, Standard (8") Screw, Hex Head (7/16-20 x 3-1/4") Washer, Steel (15/32 x 5/8 x 3/64") D NLA NLA - Caster, Semi Pneumatic (8") E NLA NLA - Caster, Semi Pneumatic, Charcoal (8") F Wheel Assembly, Semi-Pneumatic, Urethane, Light 1 1 Grey (8" x 1-3/4") 9 B Wheel Assembly w/ Bearings, Pneumatic (8" x 2") Bearing (7/16") Spacer, Bearing (7/16 x 5/8 x 1-3/4") C Hardware, Caster Axle (Pair) 1 1 NOTE: A - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - Includes Items 10 and 11 C - Includes Items 4, 6, and 7 D - Before 1/15/97 E - After 1/15/97 F - After 6/8/97 46

48 Rear Wheels and Anti-Tippers 47

49 Item Number Note Part Number Description Rear Wheels and Anti-Tippers Quantity Per Package Assembly Anti-Tipper Spring, Torsion with Double Button X013 Anti-Rattle (1") NLA NLA - Bushing, Anti-Wear NLA NLA - Tube, Support, Anti-Tipper, Black Key (6mm x 6mm x 40mm) Washer, Flat (21/64 x 53/64 x 7/64") Kit, Locking Tab Washer w/ Instruction Sheet (Pair) Screw (M8 x 1.25 x 20mm) Drive Wheel Assembly, 5 Spoke, Pneumatic (12-1/2 1 1 x 2-1/4") Includes: Locking Tab Washer with Instruction Sheet Drive Wheel Assembly, 5 Spoke w/ Foam Fill Insert 1 1 (12-1/2 x 2-1/4") Includes: Locking Tab Washer with Instruction Sheet Tire, Pneumatic, Grey (12-1/2" x 2-1/4") Tube, Inner, Black (12-1/2 x 2-1/4") A NLA NLA - Insert, Flat Free NLA NLA - Rim with Locking Tab 1 1 NOTE: A - As of 10/20/99 the "Solid" Flat Free Insert was replaced by a "Foam Fill" process. When a Flat Free Insert is requested, a complete wheel must be ordered. 48

50 Wheel Lock 49

51 Item Number Note Part Number Description NOTE: Wheel Lock Quantity Per Package Assembly NLA NLA - Bracket, Black X024 Tip, Rubber Wheel Lock Handle, Black NLA NLA - Spacer (17/64 x 31/64 x 7/16") Locknut (1/4-28) NLA NLA - Spacer, Nylon (1/4 x 7/16 x 1/8") Washer, Nylon (1/4 x 1/2 x 1/16") NLA NLA - Shoe, Wheel Lock Screw, Hex Head (1/4-20 x 1-1/4") Screw, Hex Head (1/4-28 x 3/4") NLA NLA - Link, Stop, Black NLA NLA - Handle, Wheel Lock, Black - Right NLA NLA - Handle, Wheel Lock, Black - Left Locknut (1/4-20) Bolt, Hex Head Cap (1/4-20 x 3/4") Washer (1/4 x 5/8 x 3/32") NLA NLA - Wheel Lock Assembly - Right NLA NLA - Wheel Lock Assembly - Left 1 1 A Wheel Lock Extension Handle Assembly, Black (6") 1 1 A Wheel Lock Extension Handle Assembly, Black (8") 1 1 A - Not Shown 50

52 2-Pole Motor and Gearbox NOTE: Manual recliner models for rear wheel drive continued to use the 2-pole motor/gearboxes thru 5/14/99. 51

53 2-Pole Motor and Gearbox NOTE: Manual recliner models for rear wheel drive continued to use the 2-pole motor/gearboxes thru 5/14/99. Item Number Description With Brake Lever (Before 3/15/99) Right With Brake Lever (Before 3/15/99) Left Basic Short Cap Right Basic Short Cap Left Basic Long Cap (Light Duty 250-S) Right Basic Long Cap (Light Duty 250-S) Left 1. Motor/ Gearbox NLA NLA NLA NLA Gear Box NLA NLA 3. Motor Assembly NLA NLA WARR 3. RPLMT E-NL E-NL Motor A A Assembly 4. Brake Repair NLA NLA NLA NLA NLA NLA Kit 5. Brake Cover NLA NLA NLA with Screws See Note(s) D See Note(s) D 6. Brushes with cap NLA NLA See Note(s) E (Pair) See Note(s) E Screw, 7. Phillips Pan Head (#4-40 x 1/4") NLA - 8. Coupling w/ NLA NLA Cup (1" Diameter) See Note(s) B See Note(s) B 8. Coupling w/ 50000X X007 Cup (1-5/16" See Note(s) B Diameter) See Note(s) C See Note(s) C 50000X341-N 50000X341-N 9. Spacer LA LA See Note(s) A See Note(s) A Screw, Socket Head (1/4-20 x /8") Lockwasher 10502X X001 Plastic Tip Slotted Plate NLA NLA Screw, Socket Head NLA NLA (#8-32 x 1/2") 52

54 2-Pole Motor and Gearbox NOTE: Manual recliner models for rear wheel drive continued to use the 2-pole motor/gearboxes thru 5/14/99. Item Number Description With Brake Lever (Before 3/15/99) Right With Brake Lever (Before 3/15/99) Left Basic Short Cap Right Basic Short Cap Left Basic Long Cap (Light Duty 250-S) Right Basic Long Cap (Light Duty 250-S) Left Screw, 15. Socket Head NLA NLA NLA NLA NLA NLA (M6 x 30MM) Screw, 16. Socket Head NLA NLA NLA NLA NLA NLA (M6 x 16MM) Clutch Release Extension Handle See Note(s) D See Note(s) D See Note(s) D See Note(s) D NOTE: A - Spacer not needed after 6/30/98. B - Coupling and Cup for chairs manufactured before 11/12/01 - Use part # 50000X007 as a direct replacement part. C - After 11/11/01 Coupling with Cup was resized from approximately 1" to 1-5/16" diameter and can be used as a direct replacement for part number D - Sold in pairs only E are internal brushes and do not use Caps. 53

55 4-Pole Motor and Gearbox With Brake Lever (After 3/14/99) NOTE: Manual Recliner models for Rear Wheel Drive continued to use the 2-Pole Motor/Gearboxes thru 5/14/99. See page titled "2-Pole Motor and Gearbox" 54

56 4-Pole Motor and Gearbox With Brake Lever (After 3/14/99) NOTE: Manual Recliner models for Rear Wheel Drive continued to use the 2-Pole Motor/Gearboxes thru 5/14/99. See page titled "2-Pole Motor and Gearbox" Item Number Description Right Left 1. Motor / Gearbox NLA Before 10/29/01 See Note(s) D See Note(s) D WARR RPLMT - Motor / 1. Gearbox E-NLA E-NLA Before 10/29/01 See Note(s) G See Note(s) H 1. Motor / Gearbox After 10/28/ Gearbox See Note(s) C See Note(s) C 3. Motor Assembly Before 10/29/ NLA Motor Assembly After 10/28/ NLA NLA 4. Brake Repair Kit See Note(s) F See Note(s) F 5. Brake Cover with Screws Before 10/29/ NLA NLA 5. Brake Cover (Black) with Screws After 10/28/ NLA NLA 6. Brushes with Caps See Note(s) E See Note(s) E 7. Screw, Socket Pan Head (#8-32 x 1/4") SEE ITEM 5 SEE ITEM 5 8. NLA - Coupling w/ Cup (1" NLA NLA Diameter) See Note(s) A See Note(s) A 8. Coupling w/ Cup (1-5/16" 50000X X007 Diameter) See Note(s) B See Note(s) B 9. Screw, SHC (1/4-20 x 1-1/8") See Note(s) C See Note(s) C 9. Screw, SHC (M6 x 1 x 20MM) See Note(s) C See Note(s) C 10. Plastic Tip Before 10/29/ NLA NLA 10. Plastic Tip After 10/28/ Slotted Plate Screw, Socket Head (M6 x 30MM) NLA NLA 13. Screw, Socket Head (M6 x 16MM) NLA NLA 55

57 4-Pole Motor and Gearbox With Brake Lever (After 3/14/99) NOTE: Manual Recliner models for Rear Wheel Drive continued to use the 2-Pole Motor/Gearboxes thru 5/14/99. See page titled "2-Pole Motor and Gearbox" NOTE: A - Coupling with Cup for chairs manufactured before 11/12/01 - Use part # 50000X007 as a direct replacement part. B - After 11/11/01 Coupling with Cup was resized from approximately 1" to 1-5/16" diameter and can be used as a direct replacement for part number C - When a new gearbox or mounting screws are ordered, (2 ea.) metric and (2 ea.) non-metric screws (item 9) must be ordered. Invacare Corp. utilizes alternate suppliers for this part number. D - As of May 2008, the Metal Motor End Cap will be replaced with a Composite Motor End Cap. The change does not affect form, fit, function or aesthetics. E - Kit includes (4) Brushes, (4) Brush Caps and Instruction Sheet. F - Use existing screws when installing the Brake Repair Kit. The Motor Brake Mounting Screws are not saleable. G - Part is no longer available as a service part. See part number as a replacement. H - Part is no longer available as a service part. See part number as a replacement. 56

58 Battery Boxes and Trays Light Duty, 250-S models use UI batteries with 22NF battery boxes. 57

59 Battery Boxes and Trays Light Duty, 250-S models use UI batteries with 22NF battery boxes. Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Battery Box Assembly, Dual w/ Single 1 2 Extended Connector, UI Battery Box Assembly, Rear, 22NF A,B NLA NLA - Battery Box Top Assembly, Dual w/ Single 1 2 Extended Connector, UI 2 A,B Battery Box Top, Rear, 22NF NLA NLA - Battery Box Bottom Assembly, U Battery Box Bottom with Strap, 22NF NLA NLA - Bracket, Tray Hanger, Black (16-20" W) NLA NLA - Bracket, Tray Hanger, Black (14" W) X012 Collar, Anti-Rattle (7/8") Screw, Hex Head (1/4-20 x 1-1/4") NLA NLA - Tray Assembly with Buckle NLA NLA - Screw, Hex Head (1/4-20 x 1-1/2") NLA NLA - Bumper, Rubber (UI Battery Boxes Only) Rivet, Pop (3/16") (UI Battery Boxes Only) Locknut (1/4-20) NLA NLA - Hanger, Tray Bolt, Hex Head Cap (1/4-20 x 3/4") NLA NLA - Support, Tray, Sectional NLA NLA - Support, Tray, Recliner Locknut (1/4-20) Battery Tray Assembly, NF Battery Boxes (16"-20" W) - Sectional NLA NLA - Battery Tray Assembly, NF Battery Boxes, Recliner (16-20" W) NLA NLA - Battery Tray Assembly, 1 1 UI Battery Boxes, Sectional (14" W) NLA NLA - Battery Tray Assembly, 1 1 For U1 Battery Boxes, Recliner (14" W) E 50000X166-NLA NLA - Fuse - Buss 2-1/4" L (60 AMP) 1 1 E Fuse, MIDI (Non-G/B & G/B) (80 AMP) 1 2 C,E NLA NLA - Hardware, Battery Terminal, UI Batteries 2 1 (Pair) D,E Hardware, Battery Terminal, 22NF Batteries (Pair) 2 1 NOTE: A - As of 11/05/99 the battery harness fuse changed from a Bussman 60 AMP to a MIDI 80 AMP fuse. This battery box top is compatible for chairs manufactured before 11/05/99 and must be ordered when a replacement Bussman 60 AMP fuse is requested. B - It is recommended that the new terminal hardware be ordered when a new battery box top is ordered. C - Hardware includes small battery terminal caps (gray and orange), 1/4-20 x 7/8" hex flange screws, 1/4-20 hex flange nuts, cable ties, locking tab washers and instruction sheet for two batteries. D - Hardware includes battery clamps, battery clamp cops (red and black), small battery terminal caps (red and black), 1/4-20 x 7/8" hex flange screws, 1/4-20 hex flange nuts, cable ties and locking tab washers for two batteries. E - Not Shown 58

60 Battery Charger and Harnesses 59

61 Item Number Note Part Number Description Battery Charger and Harnesses Quantity Per Package Assembly Harness, Wiring, Standard Harness, Wiring, Recliner Screw, Phillips Pan Head (#6-32 x 1-1/8") NLA NLA - Washer, Nylon (11/64 x 1/2 x 1/8") P0870X000 Nut, Hex Keps (#4-40) NLA NLA - Bracket, Charger Connector, Black Screw, Phillips Pan Head (#4-40 x 1/2") A Charger, Battery, 8 Amp, 115vac, Off Board 1 1 Dual Mode Round Plug, Lester NLA NLA - Charger, Battery, 8 Amp. 115vac, Off Board, 1 1 Dual Mode, Round Plug w/ AC Power Line Cord, Dynamic 7 D,G NLA NLA - Charger, Battery, 4 Amp. 115vac, Off Board, 1 1 Dual Mode, Round Plug, Lester 7 H,H Charger, Battery, 8 Amp. 115vac (Off Board) 1 1 Single Mode Round Plug w/ AC Power Line Cord 7 H,H E WARR RPLMT - Charger, Battery, 8 Amp, 115VAC 1 1 (Off Board) Single Mode Round Plug w/ AC Power Line Cord 8 I NLA NLA - Cord, AC Power, 115VAC, 2 Prong Off-Board 1 1 (11' 6" L) Cord, AC Power, 115VAC, 3 Prong On-Board (6' /2" L) Cable, Charger Extension, Round Plug (24" L) B NLA NLA - Wrap, Slit Wire Harness (1/2" O.D., 36" Long 1 1 Cut To Length) 11 E Fuse - Buss ATC-15 (15 AMP) F Fuse - Buss Mini ATM-15 (15 AMP) 1 2 C Package, Tie Wrap (11-1/2" L) 10 1 NOTE: A - On 7/18/01 Lester 8 AMP battery charger was reinstated. B - Plastic wire wrap replaced mesh fabric and heat shrink 9/1/99. # can be used for chairs made before 9/1/99. C - Not Shown D - Light Duty, 250-S Models Only. E - Before 4/1/03. Charger extension cable requires 1 fuse. Wiring harness requires 2 fuses F - After 3/31/03. Charger extension cable requires 2 fuses. Wiring harness requires 2 fuses G - The 4 amp. Lester charger was obsoleted and replaced with the 8 amp. CTE charger. For wet cell batteries, use the 8 amp. dual mode Lester charger. H - CTE charger introduced 4/1/04. Used on Gel Cell or AGM (Absorbed Glass Mat) batteries. For wet cell batteries refer to the 8 amp. Lester charger. H1 - CTE charger looks exactly the same as Dynamic's charger except for the company name that is silk screened on the narrow side panel, where the charger plug is (hard wired) attached. Serial number starts with 04A I - No longer available as a service part. Please use as its replacement. 60

62 Front Riggings Reference Chart Support Assemblies Riggings Color Right Color Left Chrome Right Chrome Left P PW P93ST NLA NLA NLA NLA PW93ST P93E NLA NLA NLA NLA PW93E P93M NLA NLA NLA NLA PAS4A/PAL4A (14-20" W) See Note(s) A See Note(s) A P904A NLA NLA (14-20" W) See Note(s) A See Note(s) A See Note(s) A See Note(s) A NOTE: A - Calf pads and attaching hardware not included with legrest. See page titled "Calf Pads and Attaching Harware." Pivot/Slide Tube with Footplate P93/P93E/P93M Side 14"W - Right 14"W - Left 16-20"W - Right 16-20"W - Left Alumunim Footplate (Standard ) NLA NLA "W 2" Longer - Right 16-20"W 2" Longer - Left 16-20"W 4" Longer - Right 16-20"W 4" Longer - Left NOTE: A - No longer available as a service part individually. NOTE: The Pivot/Slide tube mounting hardware is not included. Deluxe Aluminum Footplate (1450) NLA See Note(s) A NLA See Note(s) A Extra Large Aluminum Footplate (1350) NLA NLA NLA NLA NLA NLA 61

63 Front Riggings Reference Chart Pivot/Slide Tube with Footplate PW93/PW93E Side Aluminum Footplate (Standard ) Deluxe Aluminum Footplate (1450) 14"W - Right NLA 14"W - Left NLA 16-20"W - Right NLA 16-20"W - Left NLA 16-20"W 2" Longer - Right NLA 16-20"W 2" Longer - Left NLA 16-20"W 4" Longer - Right NLA 16-20"W 4" Longer - Left NLA NOTE: The Pivot/Slide tube mounting hardware is not included. Extra Large Aluminum Footplate (1350) NLA NLA Adjustable Angle Flip-up Footplate (AT5543) Pivot/Slide Tube with Footplate P93ST/PW93ST Side 16-20"W - Right 16-20"W - Left NOTE: The Pivot/Slide tube mounting hardware is not included. Composite Footplate (1651)

64 Front Riggings Reference Chart Pivot/Slide Tube with Footplate PAS4A Side Aluminum Footplate (Standard ) 14"W - Right NLA 14"W - Left NLA NOTE: The Pivot/Slide tube mounting hardware is not included. Extra Large Aluminum Footplate (1350) NLA NLA Pivot/Slide Tube with Footplate PAL4A Side Aluminum Footplate (Standard ) 16-20"W - Right "W - Left NOTE: The Pivot/Slide tube mounting hardware is not included. Extra Large Aluminum Footplate (1350) Pivot/Slide Tube with Footplate P904A Side Aluminum Footplate (Standard ) 14"W - Right NLA 14"W - Left NLA 16-20"W - Right "W - Left "W 2" Longer - Right NLA 16-20"W 2" Longer - Left NLA 16-20"W 4" Longer - Right NLA 16-20"W 4" Longer - Left NLA NOTE: The Pivot/Slide tube mounting hardware is not included. Deluxe Aluminum Footplate (1450) NLA NLA Extra Large Aluminum Footplate (1350) NLA NLA NLA NLA NLA NLA 63

65 P93 Footrest Supports 64

66 Item Number Note Part Number Description NOTE: P93 Footrest Supports Quantity Per Package Assembly Anti-Rattle, Black X057 Bushing (7/32 x 3/8 x 11/32") Screw, Phillips Pan Head (#10-32 x 11/16") Screw, Phillips Pan Head (#10-32 x 1/2") Handle, Release, Black - Right Handle, Release, Black - Left Locknut (#10-32) NLA NLA - Rivnut (#10-32) Spring, Release - Right Spring, Release - Left Bolt, Lug (5/16-24 x 1-3/8") Nut, Low Cap (5/16"-24) 1 1 A,C Tip, Plastic, Black 1 1 A,B Footrest Support Assembly, Adult, Color - Right 1 1 A,B Footrest Support Assembly, Adult, Color - Left 1 1 A Footrest Support Assembly, Adult, Silver Vein Right A Footrest Support Assembly, Adult, Silver Vein - Left 1 1 A - Not Shown B - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." C - Before 10/1/00 only 65

67 PW93 Footrest Supports 66

68 Item Number Note Part Number Description PW93 Footrest Supports Quantity Per Package Assembly Anti-Rattle, Black X057 Bushing (7/32 x 3/8 x 11/32") Screw, Phillips Pan Head (#10-32 x 11/16") Screw, Phillips Pan Head (#10-32 x 1/2") Handle, Release, Black - Right Handle, Release, Black - Left Locknut (#10-32) NLA NLA - Rivnut (#10-32) Spring, Release - Right Spring, Release - Left X012 Collar, Anti-Rattle (7/8") Screw, Hex Head (1/4-20 x 1-1/2") Spacer, Coved (1/4 x 11/16 x 1/2") Nut, Hex with Nylon Cap (1/4-20) D Insert, Threaded C Kit, Slide Tube Mounting Hardware 1 1 A,B Footrest Support Assembly, Adult, Color - Right 1 1 A,B Footrest Support Assembly, Adult, Color - Left 1 1 NOTE: A - Not Shown B - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." C - Per Side D - As of 8/15/03, the Threaded Insert was revised from 3 to 5 Holes. Threaded Insert is Backward Compatible and does not require ordering in Pairs. 67

69 P93ST Footrest Supports 68

70 P93ST Footrest Supports Item Number Note Part Number Description Quantity Per Package Assembly Screw, Phillips Pan Head (#10-32 x 11/16") Screw, Phillips Pan Head (#10-32 x 1/2") Handle, Release, Black - Right Handle, Release, Black - Left 1 1 A,B Tip, Plastic, Black 1 1 A,B Screw, Phillips Pan Head (#10-32 x 1-3/8") 1 1 A,B NLA NLA - Nut, Hex (#10-32) NLA NLA - Rivnut (#10-32) Locknut (#10-32) NLA NLA - Cushion, Tubular Foam NLA NLA - Cover, Foam Cushion Screw, Hex Head w/ Patch (1/4-20 x 3/4") Spacer, Coved (1/4 x 11/16 x 1/2") D Insert, Threaded Spring, Release - Right Spring, Release - Left NLA NLA - Bushing, Black or Color Chairs (9/32 x 3/8 x /32") Kit, Pivot/Slide Tube Mounting Hardware (Pair) 1 1 B,C NL NLA - Footrest Support Assembly, Adult, Color A Right B,C NL NLA - Footrest Support Assembly, Adult, Color A Left B NLA NLA - Footrest Support Assembly, Adult, Chrome Right B NLA NLA - Footrest Support Assembly, Adult, Chrome - Left 1 1 NOTE: A - Due to design change of Release Handle, these items are no longer used after 9/30/00. B - Not Shown C - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." D - As of 8/15/03, the Threaded Insert was revised from 3 to 5 Holes. Threaded Insert is Backward Compatible and does not require ordering in Pairs. 69

71 PW93ST Footrest Supports 70

72 Item Number Note Part Number Description PW93ST Footrest Supports Quantity Per Package Assembly Screw, Phillips Pan Head (#10-32 x 11/16") Screw, Phillips Pan Head (#10-32 x 1/2") Handle, Release, Black - Right Handle, Release, Black - Left Locknut (#10-32) NLA NLA - Rivnut (#10-32) NLA NLA - Cushion, Tubular Foam NLA NLA - Cover, Foam Cushion Spring, Release - Right Spring, Release - Left X057 Bushing (7/32 x 3/8 x 11/32") X012 Collar, Anti-Rattle (7/8") Screw, Hex Head (1/4-20 x 1-1/2") Spacer, Coved (1/4 x 11/16 x 1/2") Nut, Hex with Nylon Cap (1/4-20) D Insert, Threaded Kit, Slide Tube Mounting Hardware 1 1 A,B Screw, Phillips Pan Head (#10-32 x 1-3/8") 1 1 A,B NLA NLA - Nut, Hex (#10-32) 1 1 A,B Tip, Plastic, Black 1 1 A,C Footrest Support Assembly, Adult, Color - Right 1 1 A,C Footrest Support Assembly, Adult, Color - Left 1 1 NOTE: A - Not Shown B - Before 10/1/00 only. C - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." D - As of 8/15/03, the Threaded Insert was revised from 3 to 5 Holes. Threaded Insert is Backward Compatible and does not require ordering in Pairs. 71

73 P93E Supports 72

74 Item Number Note Part Number Description P93E Supports Quantity Per Package Assembly X008 Screw, Phillips Pan Head (#10-32 x 11/16") X002 Screw, Phillips Round Head (#10-32 x 1/2") X057 Bushing (7/32 x 3/8 x 11/32") Plug Button, Black (7/8") X012 Collar, Anti-Rattle (7/8") X009 Bolt, Lug (5/16-24 x 1-3/8") Nut, Low Cap (5/16"-24) Bumper Screw, Phillips Pan Head Tap (#10-32 x 3/4") X000 Rivnut (#10-32) Spring, Release - Right Spring, Release - Left X003 Locknut (#10-32) NLA NLA - Handle, Release, Black- Right NLA NLA - Handle, Release, Black- Left A Tip, Plastic, Black 1 1 B,C NL NLA - Footrest Support Assembly, Adult, Color A Right B,C NL NLA - Footrest Support Assembly, Adult, Color A Left C NLA NLA - Footrest Support Assembly, Adult, Chrome Right C NLA NLA - Footrest Support Assembly, Adult, Chrome - Left 1 1 NOTE: A - Before 10/1/00 Only B - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." C - Not Shown 73

75 PW93E Footrest Supports 74

76 Item Number Note Part Number Description PW93E Footrest Supports Quantity Per Package Assembly X012 Collar, Anti-Rattle (7/8") Plug Button, Black (7/8") Bumper Screw, Phillips Pan Head Tap (#10-32 x 3/4") Handle, Release, Black - Right Handle, Release, Black - Left Screw, Phillips Pan Head (#10-32 x 11/16") X057 Bushing (7/32 x 3/8 x 11/32") Screw, Phillips Pan Head (#10-32 x 1/2") Spring, Release - Right Spring, Release - Left NLA NLA - Rivnut (#10-32) Locknut (#10-32) Cap, End Tube, Black (3/4") D Insert, Threaded Screw, Hex Head (1/4-20 x 1-1/2") Spacer, Coved (1/4 x 11/16 x 1/2") Nut, Hex with Nylon Cap (1/4-20) C Kit, Slide Tube Mounting Hardware 1 1 A,B Footrest Support Assembly, Adult, Color - Right 1 1 A,B Footrest Support Assembly, Adult, Color - Left 1 1 NOTE: A - Specify frame color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - Not Shown C - Per Side D - As of 8/15/03, the Threaded Insert was revised from 3 to 5 Holes. Threaded Insert is Backward Compatible and does not require ordering in Pairs. 75

77 P93M Footrest Supports 76

78 Item Number Note Part Number Description P93M Footrest Supports Quantity Per Package Assembly X002 Screw, Phillips Round Head (#10-32 x 1/2") X008 Screw, Phillips Pan Head (#10-32 x 11/16") X057 Bushing (7/32 x 3/8 x 11/32") Nut, Low Cap (5/16"-24) Plug Button, Black (7/8") X009 Bolt, Lug (5/16-24 x 1-3/8") Spring, Release - Right Spring, Release - Left Bumper Screw, Phillips Pan Head Tap (#10-32 x 3/4") X000 Rivnut (#10-32) X003 Locknut (#10-32) Handle, Release, Black - Right Handle, Release, Black - Left C Tip, Plastic, Black 1 1 A,B NL NLA - Footrest Support Assembly, Adult, Color A Right A,B NL NLA - Footrest Support Assembly, Adult, Color A Left B NLA NLA - Footrest Support Assembly, Adult, Chrome Right B NLA NLA - Footrest Support Assembly, Adult, Chrome - Left 1 1 NOTE: A - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - Not Shown C - Before 10/1/00 only. 77

79 P904A Legrest Supports 78

80 Item Number Note Part Number Description P904A Legrest Supports Quantity Per Package Assembly Plug Button, Black (7/8") X000-NLA NLA - Screw, Slotted Truss Head (3/8-16 x 1-1/2") Washer, Nylon (25/64 x 7/8 x 1/32") X000 Hex Nut (3/8"-16) Locknut (5/16-24) Bolt, Lug (5/16-24 x 1-3/8") X040-NLA NLA - Tube, Elevating Support, Chrome - Right X041-NLA NLA - Tube, Elevating Support, Chrome - Left A Tube, Elevating Adjustable Support, Color - Right A Tube, Elevating Adjustable Support, Color - Left Plug Button, Black (3/4") NLA NLA - Tube, Legrest Support, Chrome - Right NLA NLA - Tube, Legrest Support, Chrome - Left A Tube, Legrest Support, Color - Right A Tube, Legrest Support, Color - Left Bumper Screw, Phillips Pan Head Tap (#10-32 x 3/4") 1 1 A,B Legrest Support Assembly, Adult, Color - Right 1 1 A,B Legrest Support Assembly, Adult, Color - Left 1 1 B,C NLA NLA - Legrest Support Assembly, Adult, Silver Vein Right B,C NLA NLA - Legrest Support Assembly, Adult, Silver Vein - Left 1 1 NOTE: A - Specify frame finish when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - Not Shown C - As of 7/6/07, chrome finish option is discontinued and no longer available. 79

81 PAS4A/PAL4A Articulating Legrests 80

82 PAS4A/PAL4A Articulating Legrests Item Number Note Part Number Description NOTE: Quantity Per Package Assembly NLA NLA - Tube, Legrest Support - Right NLA NLA - Tube, Legrest Support - Left Plug Button, Black (3/4") X000 Hex Nut (3/8"-16) NLA NLA - Screw, Shoulder Slotted Head (1/2 x 1-1/8", 1 1 3/8-16) NLA NLA - Tube, Support and Drive Link, Chrome - Right NLA NLA - Tube, Support and Drive Link, Chrome - Left Tube, Slide, Articulating, Chrome - Right Tube, Slide, Articulating, Chrome - Left Washer (#20) X001 Locknut (5/16-24) X009 Bolt, Lug (5/16-24 x 1-3/8") NLA NLA - Screw, Socket Button Head (3/8-16 x 3/4") Washer, Nylon (3/8 x 3/4 x 1/16") NLA NLA - Bar, Link, Black 1 1 A,B Legrest Support Assembly, Articulating, Adult, 1 1 Chrome - Right A,B Legrest Support Assembly, Articulating, Adult, 1 1 Chrome - Left A - Not Shown B " Wide 81

83 Legrest Release Handles and Ratchet Assembly 82

84 Legrest Release Handles and Ratchet Assembly Item Number Note Part Number Description Quantity Per Package Assembly Screw, Phillips Pan Head (#10-32 x 11/16") Screw, Phillips Pan Head (#10-32 x 1/2") A Screw, Phillips Pan Head (#10-32 x 1-3/8") A NLA NLA - Nut, Hex (#10-32) Handle, Release, Black - Right Handle, Release, Black - Left A Tip, Plastic, Black X057 Bushing (7/32 x 3/8 x 11/32") Spring, Release - Right Spring, Release - Left Screw (M8 x 1.25 x 20mm) NLA NLA - Rivnut (#10-32) Tip, Plastic, Black Washer, Nylon (5/16 x 11/16 x 1/16") B 42326X004 Bar, Ratchet - Right/Left C NLA NLA - Bar, Ratchet - Right C NLA NLA - Bar, Ratchet - Left X003 Spacer (5/16 x 1/2 x 3/8") Ring, Snap Cam, Legrest Spring, Release X000 Nut, Acorn (5/16-24) X002 Bracket, Release, Black Handle, Release 1 1 NOTE: A - Before 10/1/00 only. B - For 904 Legrests C - For Articulating Legrests 83

85 Calf Pads and Attaching Hardware Due to a change to the Legrest Calf Pad size made on 4/23/12, you must also order the hardware kit ( ) when ordering replacement Calf Pads. 84

86 Calf Pads and Attaching Hardware Due to a change to the Legrest Calf Pad size made on 4/23/12, you must also order the hardware kit ( ) when ordering replacement Calf Pads. Item Number Note Part Number Description Quantity Per Package Assembly 1 A,B,G X003 Pad, Legrest, Vinyl - Right A,B,G X004 Pad, Legrest, Vinyl - Left A,C,D, G NLA NLA - Pad with Screws, Legrest (Pair) A,C,E, G Pad, Legrest, Vinyl - Right/Left X000-NLA NLA - Cover, Legrest Pad X006-NLA NLA - Screw, Phillips Pan Head (#10-14 x 1/16") X019 Plate, Legrest Pad Locknut (5/16-24) Spacer, Legrest Pad, Black Spacer, Legrest Pad Mounting, Black Screw, Hex Head (5/16-24 x 3-1/2") Screw, Hex Head (5/16-24 x 1-1/2") F Hardware, Legrest Pad 1 1 Screw, Phillips Pan Head (#10-32 x 11/16") 1 2 Screw, Phillips Pan Head (#10-32 x 1") 1 2 Instruction Sheet, Legrest Pad Mtg X008 Spring, Leaf X001 Locknut (5/16-24) Bracket, Legrest, Chrome Screw, Hex Head (5/16-24 x 3-1/4") 1 1 NOTE: A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B " Wide C " Wide D - Before 9/5/00 E - After 9/4/00 F - Includes Screws and Instruction Sheet. G - Due to a change to the Legrest Calf Pad size made on 4/23/12, you must also order the hardware kit ( ) when ordering replacement Calf Pads. 85

87 Pivot/ Slide Tube and Footplate P93, P93E, P93M NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". 86

88 Pivot/ Slide Tube and Footplate P93, P93E, P93M NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". Item Number Note Part Number Description Quantity Per Package Assembly Plug Button, Black (3/4") D,E,B Pivot/Slide Tube w/ Plug Button, Black E NLA NLA - Pivot/Slide Tube w/ Plug Button, Black (2" 1 1 Longer) 2 E NLA NLA - Pivot/Slide Tube w/ Plug Button, Black (4" 1 1 Longer) NLA NLA - Pivot/Slide Tube w/ Plug Button, Deluxe 1 1 Aluminum, Black 3 C 44200X059 Footplate, Aluminum, Small, Black (6-3/4" W x 6" L) A 44200X027 Footplate, Aluminum, Medium, Black (7-3/4" W x 6" 1 1 L) NLA NLA - Footplate, Aluminum, Deluxe, Black - Right 1 1 (8" W x 5-3/4" L) NLA NLA - Footplate, Aluminum, Deluxe, Black - Left (8" 1 1 W x 5-3/4" L) 3 C Footplate, Aluminum, Extra Large, Black - Right (7" 1 1 W x 8-1/2" L) 3 C Footplate, Aluminum, Extra Large, Black - Left (7" W 1 1 x 8-1/2" L) X025 Footplate, Aluminum, Extra Large, Black - Right (8" 1 1 W x 8-1/2" L) X026 Footplate, Aluminum, Extra Large, Black - Left (8" W 1 1 x 8-1/2" L) 4 D Cap, End, Tube, Black (7/8") E Plug Button, Black (7/8") D Spring, Tension B NLA NLA - Spring E,F Spring, Leaf X001 Screw, Phillips Pan Head (#8-32 x 3/8") Plug, Push, Footplate 1 1 NOTE: A - Aluminum footplates on chairs built before 2/96 had a "Bright aluminum" finish. Footplates after 1/96 now have a black finish. When replacing 1 Bright aluminum footplate, it is suggested that 2 new (black) footplates are ordered. B - Deluxe Aluminium Footplate C - 14" Wide D - Standard Aluminium Footplate E - Extra Large Aluminium Footplate F - Use one or more leaf springs per assembly as required such that footplate may be moved by hand to the up-right position and remain in place. 87

89 Pivot/ Slide Tube and Footplate PW93, PW93E NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". 88

90 Pivot/ Slide Tube and Footplate PW93, PW93E NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". Item Number Note Part Number Description Quantity Per Package Assembly Plug Button, Black (3/4") A,B Pivot/Slide Tube w/ Plug Button, Black A,B Pivot/Slide Tube w/ Plug Button, Black (2" Longer) A,B Pivot/Slide Tube w/ Plug Button, Black (4" Longer) C NLA NLA - Tube, Pivot/Slide w/ Plug Button, Deluxe 1 1 Aluminum, Black 3 D 44200X059 Footplate, Aluminum, Small, Black (6-3/4" W x 6" L) E 44200X027 Footplate, Aluminum, Medium, Black (7-3/4" W x 6" 1 1 L) 3 F Footplate, Aluminum, Extra Large, Black - Right (7" 1 1 W x 8-1/2" L) 3 F Footplate, Aluminum, Extra Large, Black - Left (7" W 1 1 x 8-1/2" L) 3 G 44200X025 Footplate, Aluminum, Extra Large, Black - Right (8" 1 1 W x 8-1/2" L) 3 G 44200X026 Footplate, Aluminum, Extra Large, Black - Left (8" W 1 1 x 8-1/2" L) 3 H NLA NLA - Footplate, Aluminum, Deluxe, Black - Right 1 1 (8" W x 5-3/4" L) 3 H NLA NLA - Footplate, Aluminum, Deluxe, Black - Left (8" 1 1 W x 5-3/4" L) 4 A Cap, End, Tube, Black (7/8") B Plug Button, Black (7/8") A Spring, Tension C NLA NLA - Spring B,I Spring, Leaf X001 Screw, Phillips Pan Head (#8-32 x 3/8") Plug, Push, Footplate 1 1 NOTE: A - For Standard Aluminium Footplates B - For 1350 Extra Large Aluminium Footplates C - For 1450 Deluxe Aluminium Footplates D - For 14" wide with Standard Aluminum Footplates E - For 16-20" wide with Standard Aluminum Footplates F - For 14" wide with 1350 Extra Large Aluminum Footplates G - For 16-20" wide with 1350 Extra Large Aluminum Footplates H - For 16-20" wide with 1450 Deluxe Aluminum Footplates I - Use one or more leaf springs per assembly as required such that footplate may be moved by hand to the up-right position and remain in place. 89

91 Pivot/ Slide Tube and Footplate P93ST/PW93ST NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". 90

92 Pivot/ Slide Tube and Footplate P93ST/PW93ST NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". Item Number Note Part Number Description Quantity Per Package Assembly 1 D Tube, Pivot/Slide, Curved End, Black - Long (9-7/8") E Tube, Pivot/Slide, Curved End, Steel, Black (9-7/8") Spacer, Coved (1/4 x 3/4 x 11/32") Plug Button, Black (3/4") Locknut (1/4-20) X006 Screw, Socket Head (1/4-20 x 2-1/4") A Footplate, Composite, Small, Black (6" W x 6" L) B Footplate, Composite, Medium, Black (7" W x 6" L) C Footplate, Composite, Large, Black (8" W x 6" L) 1 1 NOTE: A - For chairs 16" wide B - For chairs 18" wide C - For chairs 20" wide D - P93ST E - PW93ST 91

93 Pivot/ Slide Tube and Footplate P904, PAL4A, PAS4A NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". 92

94 Pivot/ Slide Tube and Footplate P904, PAL4A, PAS4A NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". Item Number Note Part Number Description Quantity Per Package Assembly Plug Button, Black (3/4") C,E,F Pivot/Slide Tube w/ Plug Button, Black C Pivot/Slide Tube Assembly, Extra Large, Standard 1 1 Aluminium - 2" Longer, Black 2 C,E,F Pivot/Slide Tube w/ Plug Button, Black (4" Longer) B,E,F Pivot/Slide Tube w/ Plug Button Assembly, Chrome C,G NLA NLA - Pivot/Slide Tube w/ Plug Button, Deluxe, 1 1 Black 3 D 44200X059 Footplate, Aluminum, Small, Black (6-3/4" W x 6" L) A 44200X027 Footplate, Aluminum, Medium, Black (7-3/4" W x 6" 1 1 L) NLA NLA - Footplate, Aluminum, Deluxe, Black - Right 1 1 (8" W x 5-3/4" L) NLA NLA - Footplate, Aluminum, Deluxe, Black - Left (8" 1 1 W x 5-3/4" L) 3 D Footplate, Aluminum, Extra Large, Black - Right (7" 1 1 W x 8-1/2" L) 3 D Footplate, Aluminum, Extra Large, Black - Left (7" W 1 1 x 8-1/2" L) X025 Footplate, Aluminum, Extra Large, Black - Right (8" 1 1 W x 8-1/2" L) X026 Footplate, Aluminum, Extra Large, Black - Left (8" W 1 1 x 8-1/2" L) 4 E Cap, End, Tube, Black (7/8") F Plug Button, Black (7/8") E Spring, Tension G NLA NLA - Spring F,H Spring, Leaf X001 Screw, Phillips Pan Head (#8-32 x 3/8") Plug, Push, Footplate 1 1 NOTE: A - Aluminum footplates on chairs built before 2/96 had a "Bright aluminum" finish. Footplates after 1/96 now have a black finish. When replacing 1 Bright aluminum footplate, it is suggested that 2 new (black) footplates be ordered. B - PAL4/PAS4A C - P904 D - 14" Wide E - Standard Aluminium Footplate F - Extra Large Aluminium Footplate G - Deluxe Aluminium Footplate H - Use one or more leaf springs per assembly as required such that footplate may be moved by hand to the up-right position and remain in place. 93

95 AT5543 Adjustable Angle Footplate Assemblies PW93, PW93E NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". 94

96 AT5543 Adjustable Angle Footplate Assemblies PW93, PW93E NOTE: Heel loops are not included. See page titled "Footrest and Legrest Accessories". NOTE: For complete pivot/slide tube and footplate assemblies, see page titled "Front Riggings Reference Chart". Item Number Note Part Number Description Quantity Per Package Assembly 1 B,D Footplate, Adjustable Angle, Large, Black (5-1/4" W 1 1 x 8" L) 1 C,D Footplate, Adjustable Angle, Extra Large, Black 1 1 (6-1/4" W x 8" L) 2 A Clamp, Footplate Tube, Pivot and Slide, Straight, Steel, Black (9-7/8" 1 1 L) Screw, Nylon Adjustment (1/2-13 x 7/8") Hinge, Footplate - Right Hinge, Footplate - Left A Screw, Socket Flat Head (1/4-20 x 3/4") Screw, Socket Button Head (1/4-20 x 1-7/8") Spacer, Coved (1/4 x 3/4 x 11/32") Washer (1/4 x 23/32 x 1/16") Washer, Nylon (5/16 x 7/8 x 1/8") Washer (1/4 x 1/2 x 1/16") A Nut, Barrel, Hex Head (1/4-20 x 11/16") Locknut (1/4-20) 1 1 NOTE: A - Items 2, 6 and 12 must be ordered together for chairs manufactured before 8/10/99 due to a hardware change. B - 14" Wide. C - 16" and Wider. D - This footplate was revised 9/2/2008 with rounder corners and accessory holes changed from 8 to 4. Recommended to replace footplate in pairs to match sides. 95

97 S1263 One Piece Wooden Footboard and Hardware P93, P93E, P93M, PW93, PW93E 96

98 S1263 One Piece Wooden Footboard and Hardware Item Number Note Part Number Description P93, P93E, P93M, PW93, PW93E Quantity Per Package Assembly 1 See Chart #1 One Piece Wooden Footboard without Hardware 1 1 A See Chart Heel Loop Hardware Packages (not shown) B Kit, Wooden Footboard Mounting Hardware Screw, Phillips Oval Head (#10-32 x 1-1/2") NLA - Screw, Phillips Oval Head (#10-32 x 1-1/4") NLA - Tube, Slide - Right NLA - Tube, Slide - Left Plug Button, Black (3/4") Locknut (#10-32) Cap, End, Tube, Black (7/8") Lock, Pad Plate, Legrest, Black Clamp, Black Washer, Nylon (3/16 x 7/16 x 1/8") NLA - Link, Locking, Chrome C Kit, Wooden Footboard Mounting Hardware Screw, Phillips Oval Head (#10-32 x 1-1/2") NLA - Screw, Phillips Oval Head (#10-32 x 1-1/4") Tube, Pivot/Slide, Chrome - Right (9-1/2" L) Tube, Pivot/Slide, Chrome - Left (9-1/2" L) Plug Button, Black (3/4") Locknut (#10-32) Cap, End, Tube, Black (7/8") Lock, Pad Plate, Legrest, Black Clamp, Black Washer, Nylon (3/16 x 7/16 x 1/8") NLA - Link, Locking, Chrome 1 1 NOTE: A - Not Shown. B - Includes items 3-12 and used for P93, P93E, P93M and P904 C - Includes items 3-12 and used for PW93 andpw93e only. #1 One Piece Wooden Footboard without Hardware 97

99 S1263 One Piece Wooden Footboard and Hardware P93, P93E, P93M, PW93, PW93E #1 One Piece Wooden Footboard without Hardware Footrest- Footboard w/ Heel Loop Holes Part Number Footrest- Footboard w/o Heel Loop Holes Part Number 48247X003-NLA 48247X X NLA Chair Width 14" 16" 18" 20" Footboard Width 11-5/8" 13-3/4" 15-9/16" 17-1/2" Footboard Depth 6" 6" 6" 6" 98

100 S1263 One Piece Wooden Footboard and Hardware P93, P93E, P93M, PW93, PW93E Heel Loop Hardware Packages (not shown) (All hardware is included to attach heel loops to footboard.) Chair Width 14-15" Wide 16"-24" Wide Part Number Package Includes 2 each Heel Loops 4 each Screw, PPH (1/4-20 x 3") 4 each Spacer (1/4 x 11/32 x 1-3/4") 4 each Locknut (1/4-20) 2 each Heel Loops 4 each Screw, PPH (1/4-20 x 3") 4 each Spacer (1/4 x 11/32 x 1-3/4") 4 each Locknut (1/4-20) 99

101 Footrest and Legrest Accessories NOTE: Heel loops for Power Articulating Legrest located on Power Articulating Legrest page. Toe Loops (1345) Footplate Type 1651, 1650, 1450, 1350, Footplates AT5543 Footplates Toe Loop w/o Hardware Single # 04572X X025 Toe Loop w/o Hardware Pair # Attaching Hardware Part Number Attaching Hardware Consists of (4) Screw, Phillips Pan Head (#10-32 x 7/8"), (4) Washer (1/4 x 3/4 x 3/32") (4) Locknut (#10-32) (4) Screw, Phillips Pan Head (#10-32 x 1/2") (4) Washer (1/4 x 3/4 x 3/32") Heel Loops (1346) Footplate Type Composite (1651) 16" Wide Tapered Composite (1651) 18" Wide Tapered Composite (1651) 20" Wide Tapered Standard Aluminum (1650) 14" Wide Standard Aluminum (1650) 16-20" Wide Heel Loop Single # NLA NLA Heel Loop Pair # Heel Loop with Ankle Strap - Right Single # NLA NLA NLA Heel Loop with Ankle Strap - Left Single # NLA NLA NLA Heel Loop with Ankle Strap Pair # Attaching Hardware Pair #

102 Footrest and Legrest Accessories NOTE: Heel loops for Power Articulating Legrest located on Power Articulating Legrest page. Heel Loops (1346) Footplate Type Heel Loop Single # Heel Loop Pair # Heel Loop with Ankle Strap - Right Single # Heel Loop with Ankle Strap - Left Single # Heel Loop with Ankle Strap Pair # Attaching Hardware Pair # Deluxe Aluminum (1450) 16-20" Wide X-Large Aluminum (1350) NLA NLA NLA " Wide X-Large Aluminum (1350) " Wide NLA Adjustable Angle (AT5543) See Note(s) B See Note(s) A See Note(s) A NOTE: A - These Assemblies include the Attaching Hardware. B - No longer available. Use part number as replacement NLA

103 Footrest and Legrest Accessories NOTE: Heel loops for Power Articulating Legrest located on Power Articulating Legrest page. Heel Loop Hardware Footplate Type Part Number Consists of: (2) Heel Loops Adjustable Angle (AT5543) Adjustable Angle (AT5543) Composite 16-20" W (1651) X-Large Aluminum 14-20" W (1350) Standard Aluminum 14-20" W (1650) Deluxe Aluminum 16-20" W (1450) NLA (4) Screw, Phillips Pan Head (1/4-20 x 2-1/4") (4) Spacer (4) Locknut (1/4-20) (2) Heel Loops w/ Ankle Straps (4) Screw, Phillips Pan Head (1/4-20 x 2-1/4") (4) Spacer (4) Locknut (1/4-20) (2) Screw, Phillips Pan Head (1/4-20 x 2-1/4") (2) Spacer (1/4 x 11/32 x 1-3/4") (2) Hex Nut w/ Nylon Cap (1/4-20) (2) Flat Washer (1/4 x 5/8 x 1/16") (2) Screw, Phillips Pan Head (1/4-20 x 2-1/4") (2) Spacer (1/4 x 11/32 x 1-3/4") (2) Locknut (1/4-20") (2) Screw, Phillips Pan Head (1/4-20 x 2-1/2") (2) Spacer (1/4 x 11/32 x 1-3/4") (2) Locknut (1/4-20") (2) Screw, Phillips Pan Head (1/4-20 x 2-1/2") (2) Spacer (1/4 x 11/32 x 1-3/4") (2) Locknut (1/4-20") Miscellaneous Accessories Part Number See Note(s) B Description Impact Guard (8") (IMPACTG) Non-Removable Device (1820) "H" Heel Strap (9342) 14" Wide "H" Heel Strap (9342) 16-20" Wide 102

104 Footrest and Legrest Accessories NOTE: Heel loops for Power Articulating Legrest located on Power Articulating Legrest page. Miscellaneous Accessories Part Number Description NOTE: See Note(s) A See Note(s) A See Note(s) A NLA See Note(s) A NLA See Note(s) A NLA Calf Strap (1337) Footrest Support Panel (1348) 14-16" Wide Footrest Support Panel (1348) 18" Wide Footrest Support Panel (1348) 20" Wide Legrest Support Panel (1348) 14-16" Wide Legrest Support Panel (1348) 18" Wide Legrest Support Panel (1348) 20" Wide See Note(s) A A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." B - For 70 deg. Tapered Footrest. NOTE: These items are not shown 103

105 Front Riggings - Adjustable Heel Loops 104

106 Front Riggings - Adjustable Heel Loops Item Number Note Part Number Description Quantity Per Package Assembly 1 A Kit, Heel Loop, Adjustable w/ Hardware (Pair) Heel Loop NLA - Spacer (1/4 x 11/32 x 1-3/4") NLA - Screw, Phillips Pan Head (1/4-20 x 2-1/4") Washer, Flat (1/4 x 5/8 x 1/16") Nut, Hex, Nylon Cap (1/4-20) 1 2 Instruction Sheet, Adjustable Heel Loop B Kit, Heel Loop, Adjustable w/ Hardware, Deluxe (Pair) 2 Heel Loop NLA - Spacer (1/4 x 11/32 x 1-3/4") Nut, Hex, Nylon Cap (1/4-20) NLA - Screw, Phillips Pan Head (1/4-20 x 2-1/2") 1 2 Instruction Sheet, Adjustable Heel Loop 1 1 NOTE: A - Kit includes items 2-6. Used with All Footplates except Deluxe (1450). B - Kit includes items 2, 3, 6, and item 7. Used with Deluxe (1450) Footplates only. 105

107 MKIV Joysticks RII, RX, A, A+, TCHJOY 106

108 Item Number Note Part Number Description NOTE: MKIV Joysticks RII, RX, A, A+, TCHJOY Quantity Per Package Assembly A,C NLA NLA - Joystick/Controller, MKIV RII 1 1 B Controller, MKIV RII, Retro 1 1 B NLA NLA - Programmer, Remote 1 1 B See Chart MKIV Joysticks 1 1 A - For chairs made before 5/1/00, the following must be ordered, RII Joystick # , RII Retro Controller # and Remote Programmer # B - Not Shown C - For joystick inductive and switch components, refer to chart under RII joystick assembly # Item Number Description RII RX A A Before 9/1/96 After 8/31/96 A+ TCHJOY See Pictorial Joystick Assembly NLA NLA NLA NLA NLA NLA 1 Knob, Joystick Skirt, Joystick Inductive, Joystick NLA NLA NLA NLA NLA 3 Before 10/1/ See Note(s) E See Note(s) B See Note(s) C See Note(s) B See Note(s) C See Note(s) B Inductive, Joystick NLA NLA After 9/20/02 See Note(s) E See Note(s) D See Note(s) D Boot, 50000X364-N 50000X364-N 50000X364-N 50000X364-N 50000X364-N Joystick LA LA LA LA LA Overlay, Joystick Decal Cable Assembly Before 10/1/02 Cable Assembly After 9/20/02 Potentiometer, Speed (Speed Pot) Before 10/1/ NLA NLA NLA NLA NLA See Note(s) A NLA NLA NLA NLA See Note(s) A See Note(s) C See Note(s) B See Note(s) C See Note(s) B NLA See Note(s) D NLA See Note(s) D See Note(s) B See Note(s) C See Note(s) C 107

109 MKIV Joysticks RII, RX, A, A+, TCHJOY A A Item Number Description RII RX A+ TCHJOY Before 9/1/96 After 8/31/96 7 Potentiometer, Speed (Speed Pot) After 9/30/02 See Note(s) D See Note(s) D 8 Knob, NLA NLA Potentiometer NLA NLA Switch, On/Off Momentary Before 10/1/02 See Note(s) B See Note(s) C See Note(s) B Switch, 9 On/Off NLA Momentary After 9/20/02 See Note(s) D 10 Switch, Off/ NLA Before 10/1/02 See Note(s) C Switch, NLA 10 Off/ 1-2 After 9/20/02 See Note(s) D 11 Switch, NLA Program See Note(s) B 12 Switch, Toggle SPDT See Note(s) B NOTE: A - Cable assembly and joystick overlay decal for RII joystick before 10/01/02 and after 9/30/02 are not available. B - Item requires soldering. C - Before 10/01/02 item requires soldering. D - After 9/30/02 item has a non-solder connector. E - The Dynamic inductive shaft will have a hole drilled 1/4" down from the top. Flightlink doesn't have this feature. 108

110 MKIV Joysticks PS, PSF and PSR NOTE: PSR STANDARD joystick configuration below show the on/off switch on the left side for part # When the on/off switch is required on the right side, refer to part number and order as a configurated part. 109

111 MKIV Joysticks PS, PSF and PSR NOTE: PSR STANDARD joystick configuration below show the on/off switch on the left side for part # When the on/off switch is required on the right side, refer to part number and order as a configurated part. Item Number Description PS Before 12/1/97 PSF After 11/30/97 PSR After 11/30/97 See Pictorial Joystick Assembly NLA See Pictorial Joystick Assembly NLA NLA See Pictorial Joystick Assembly NLA See Pictorial Joystick Assembly NLA See Pictorial Joystick Assembly NLA 1 Knob, Joystick Skirt, Joystick Inductive, Joystick See Note(s) A NLA NLA NLA 4 Boot, Joystick 50000X364-NLA 50000X364-NLA 50000X364-NLA 5 Overlay, Joystick Decal NLA NLA NLA 6 Cable Assembly NLA NLA NLA 7 Potentiometer Speed Knob Potentiometer NLA NLA 9 Switch, On/Off Momentary Switch, Push Button SPST Momentary NLA NLA 11 Switch, Push Button SPST NLA 12 Boot, Switch NLA NLA 13 Boot, Switch NOTE: A - The Dynamic inductive shaft will have a hole drilled 1/4" down from the top. Flightlink doesn't have this feature. 110

112 MKIV Joystick Mounting Hardware and Joystick Accessories 111

113 MKIV Joystick Mounting Hardware and Joystick Accessories Item Number Note Part Number Description Quantity Per Package Assembly 1 J Kit, Straight Joystick Tube with Hardware C Kit, Straight Joystick Tube with Hardware D Kit, Straight Joystick Tube with Hardware A,A1,E Kit, 1/2" Offset Joystick Tube with Hardware F Plug Button, Black (7/8") Screw, Phillips Pan Head (#4-40 x 3/8") Package, Tie Wrap (11-1/2" L) Spacer, Joystick Tube, Black Screw, Phillips Pan Head (#10-32 x 1-1/8") G NLA NLA - Hardware, Joystick Tube Mounting A,A1,H Clamp, Fixed Height Joystick Tube Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Joystick Mounting, Black X004-NLA NLA - Screw, Hex Head (1/4-20 x 1-1/8") Kit, Toggle Switch Extension Screw, Phillips Round Head (#10-32 x 3/8") Clamp, Height Adjustable Joystick Tube (ARM250) 1 1 I Extension, Joystick, "T" Style (1560) 1 1 (4" W x 5-1/2" L) I Extension, Joystick, Straight Style (1561) (1/2" W x 5" L) 1 1 NOTE: A - The joystick straight tube changed to an offset joystick tube on 10/4/00. The joystick tube mounting hardware also changed to a new fixed height clamp assembly to allow an individual to use an A1 - adjustment lever to securely hold the joystick tube in place. The fixed height joystick tube clamp can be used as a direct replacement in the field for the joystick tube mounting hardware part number manufactured for chairs before 10/4/00. C - Includes Items 3, 4, and mounts to a TCHJOY Touchpad "A" joystick D - Includes Items 3, 5, 6, 7, and mounts to MKIV RII, RX, A, A+, PSF/PSR Joysticks Before 10/4/00 E - Includes Items 3, 5, 6, 7, and mounts to MKIV RII, RX, A, A+, PSF/PSR Joysticks After 10/3/00 F - Touchpad "A" Joystick-Takes 2 G - Includes Items and used for PS, TCHJOY, and (RII, RX, A, A+, PSF/PSR joysticks Before 10/4/00) H - Used for RII, RX, A, A+, PSF/PSR joysticks After 10/3/00 I - Not Shown J - Includes Items 3, 16, and mounts to a PS joystick 112

114 MKIV Swivel Joystick Hardware 113

115 Item Number Note Part Number Description MKIV Swivel Joystick Hardware Quantity Per Package Assembly Spacer, Joystick Tube, Black Screw, Phillips Pan Head (#10-32 x 1-1/8") NLA NLA - Bracket, Swivel Joystick, MKIV NLA NLA - Bracket, Swivel Joystick with Hardware NLA NLA - Joystick Swivel Tube with Hardware, Black NLA NLA - Washer, Flat (1/4 x 3/8 x 1/16") Bushing NLA NLA - Spring, Hitch Bracket NLA NLA - Knob, Clamping, Grey NLA NLA - Tube, Swivel Joystick, Black Plug Button, Black (7/8")

116 MKVI Mid-Line Swing Bracket Assembly 115

117 MKVI Mid-Line Swing Bracket Assembly Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Tube, Adjustment, Inside, Mid-Line, Black NLA NLA - Spring, Extension (9/16 x 1-3/8" L) NLA NLA - Tube, Adjustment, Outside, Mid-Line, Black Adjustment Lock Assemnbly, Black B Swing Bracket Assembly, Mid-Line, Black X004-NLA NLA - Screw, Hex Head (1/4-20 x 1-1/8") Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Joystick Mounting, Black Half Clamp, Non-Threaded Holes Half Clamp, Threaded Holes A NLA NLA - Hardware, Joystick Tube Mounting 1 1 NOTE: A - Includes Items 6-10 B - Includes Items

118 Quad Link Assembly Before 4/07/06 117

119 Item Number Note Part Number Description 1 A A B,E B Quad Link Assembly Before 4/07/06 Quantity Per Package Assembly Kit, Quad Link Assembly - Right 1 1 Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-32) 1 2 NLA - Screw, Cap, Socket Head (#10-32 x 1/2") 1 4 NLA - Bushing, Bronze (3/16 x 1/4 x 1/4") 1 4 Screw, Phillips Pan Head (#10-32 x 1-1/8") 1 4 Spacer, Joystick Tube, Black 1 1 Stud Plate, Quad Link 1 1 Screw, Hex Head (1/4-20 x 1-1/2") 1 3 Spacer (1/4 x 3/8 x 3/16") 1 3 Half Clamp, Non-Threaded Holes 1 1 Half Clamp, Threaded Holes Kit, Quad Link Assembly - Left 1 1 Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-32) 1 2 NLA - Screw, Cap, Socket Head (#10-32 x 1/2") 1 4 NLA - Bushing, Bronze (3/16 x 1/4 x 1/4") 1 4 Screw, Phillips Pan Head (#10-32 x 1-1/8") 1 4 Spacer, Joystick Tube, Black 1 1 Stud Plate, Quad Link 1 1 Screw, Hex Head (1/4-20 x 1-1/2") 1 3 Spacer (1/4 x 3/8 x 3/16") 1 3 Half Clamp, Non-Threaded Holes 1 1 Half Clamp, Threaded Holes NLA Kit, Quad Link Assembly - Right 1 1 Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-32) 1 2 NLA - Screw, Cap, Socket Head (#10-32 x 1/2") 1 4 NLA - Bushing, Bronze (3/16 x 1/4 x 1/4") 1 4 Plate, Stud, Quad Link For 1556 Heavy Duty 1 1 Joystick Screw, Hex Head (1/4-20 x 1-1/2") 1 3 Spacer (1/4 x 3/8 x 3/16") 1 3 Half Clamp, Non-Threaded Holes 1 1 Half Clamp, Threaded Holes 1 1 Screw, Phillips Flat Head (#10-32 x 1-1/8") NLA - Kit, Quad Link Assembly - Left 1 1 Ball Plunger Assembly with Lock Washer 2 1 Locknut (#10-32) 1 2 NLA - Screw, Cap, Socket Head (#10-32 x 1/2") 1 4 NLA - Bushing, Bronze (3/16 x 1/4 x 1/4") 1 4 Plate, Stud, Quad Link For 1556 Heavy Duty 1 1 Joystick 118

120 Item Number Note Part Number Description Quad Link Assembly Before 4/07/06 Quantity Per Package Assembly 9 Screw, Hex Head (1/4-20 x 1-1/2") Spacer (1/4 x 3/8 x 3/16") Half Clamp, Non-Threaded Holes Half Clamp, Threaded Holes Screw, Phillips Flat Head (#10-32 x 1-1/8") C NLA NLA - Kit, Quad Link Assembly - Right 1 1 For TCHJOY/TCPDM4 Touchpad 2 Ball Plunger Assembly with Lock Washer Locknut (#10-32) NLA - Screw, Cap, Socket Head (#10-32 x 1/2") NLA - Bushing, Bronze (3/16 x 1/4 x 1/4") Screw, Phillips Pan Head (#10-32 x 1-1/8") NLA - Plate, Stud, Quad Link 1 1 MKIV TCHJOY/TCPDM4 9 Screw, Hex Head (1/4-20 x 1-1/2") Spacer (1/4 x 3/8 x 3/16") Half Clamp, Non-Threaded Holes Half Clamp, Threaded Holes NLA - Screw, Phillips Flat Head Countersunk (# x 3/8") 1 D NLA NLA - Kit, Quad Link Assembly - Right 1 1 For PS joystick 2 Ball Plunger Assembly with Lock Washer Locknut (#10-32) NLA - Screw, Cap, Socket Head (#10-32 x 1/2") NLA - Bushing, Bronze (3/16 x 1/4 x 1/4") NLA - Plate, Stud, Quad Link 1 1 P.S. Joystick 9 Screw, Hex Head (1/4-20 x 1-1/2") Spacer (1/4 x 3/8 x 3/16") Half Clamp, Non-Threaded Holes Half Clamp, Threaded Holes Screw, Phillips Pan Head (#10-32 x 11/16") Ball Plunger Assembly with Lock Washer 2 1 NOTE: A - Includes the Quad Link, items 2-12 and used with MKIV RII, RX, A, A+, PSF/PSR joysticks B - Includes the Quad Link, items 2-5, 8-13 and used with a 1556 Heavy Duty joystick C - Includes the Quad Link, items 2-6, 8-12, 14 and used with MKIV TCHJOY/TCPDM4 joysticks. For left side mounted Quad Link, order as a special. D - Includes the Quad Link, items 2-5, 8-12, 15 and used with a PS joystick E - Quad Link Assembly is no longer available. Please see Quad Link Assembly (After 4/06/06) category and use new Quad LInk design as a replacement. 119

121 Quad Link Assembly (QL) After 4/06/06 When converting an old style Quad Link that attaches to a mounting plate or (a Flex or Touch Pad Joystick Tube) is currently on the chair then order the following for ASBA Seat; Quad Link Mtg. Hdwr. (item 4), Quad Link (item 1) & Ht. Adj. Joystick Tube Clamp (item 11) NOTE: Substitute (item 4) with 2 ea. of the PPH Screws (item 5) when an offset joystick tube is currently on the chair. Additional Joystick Mtg. Hdwr. must be ordered when a 1556 Heavy Duty or TCPD Touch Pad is used. 120

122 Quad Link Assembly (QL) After 4/06/06 When converting an old style Quad Link that attaches to a mounting plate or (a Flex or Touch Pad Joystick Tube) is currently on the chair then order the following for ASBA Seat; Quad Link Mtg. Hdwr. (item 4), Quad Link (item 1) & Ht. Adj. Joystick Tube Clamp (item 11) NOTE: Substitute (item 4) with 2 ea. of the PPH Screws (item 5) when an offset joystick tube is currently on the chair. Additional Joystick Mtg. Hdwr. must be ordered when a 1556 Heavy Duty or TCPD Touch Pad is used. Item Number Note Part Number Description Quantity Per Package Assembly Quad Link (QL) with Instruction Sheet - Right Quad Link (QL) with Instruction Sheet - Left A Kit, Quad Link Latch Hardware B Kit, Quad Link Screw Fastener Hardware C,C Kit, ASBA/ADJASBA Quad Link Mounting Hardware Screw, Phillips Pan Head w/ Patch (#10-32 x 3/4") Screw, Phillips Pan Head (#10-32 x 1-1/8") Tie Wrap (11-1/2" L) Spacer, Joystick Tube, Black Tube, Joystick Offset (2") Plug Button, Black (7/8") Screw, Phillips Pan Head w/ Patch (#10-32 x 3/4") Clamp, Fixed Height Joystick Tube D NLA Kit, 1556 Heavy Duty Joystick To Quad Link 1 1 Mounting Hardware 13 Screw, Phillips Pan Head (#10-32 x 1/2") NLA - Plate, 1556 HD Joystick Quad Link E Kit, TCPD Touch Pad To Quad Link Mounting 1 1 Hardware 16 Plate, TCPD Touch Pad Quad Link Screw, Phillips Pan Head (#4-40 x 3/8") 1 4 F Instruction Sheet, Quad Link 1 1 NOTE: A - Latch Kit includes 4 ea. Button Head Cap Screws (10-32 x 3/8"), 2 ea. Latch Spring Assembly, 4 ea. Phillips Flat C'Sunk Head Screws, 2 ea. Spring Catch Plates, 2 ea. Socket Head Set Screws (10-32 x 3/8") B - Screw Fastener Kit includes 4 ea. Socket Head Shoulder Screws (3/8 x 3/8"), 2 ea. Socket Head Cap Screws (1/4-20 x 3/8"), 2 ea. Socket Head Set Screws (1/4-20 x 1/2"), 4 ea. Socket Head Set Screws (10-32 x 1/8") C - Includes items The Quad Link Mounting Hardware accommodates MKIV RII, and PSF/PSR joysticks. C1 - When ordering the Quad Link for the first time, Additional hardware is required for 1556 Heavy Duty and TCPD Touch Pad joysticks. See pictorial for reference. D - Includes items 13 and 14 E - Includes items 16 and 17 F - Not Shown 121

123 MKIV Controller, Programmer and Attaching Hardware 122

124 MKIV Controller, Programmer and Attaching Hardware Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Controller, MKIV Quad Pulse A,G Controller, MKIV RII, Retro NLA NLA - Screw, Hex Head w/ Patch (1/4-20 x 1-1/4") NLA NLA - Screw, Hex Head w/ Patch (1/4-20 x 1-3/4") Spacer (5/16 x 15/32 x 1/4") B NLA NLA - Programmer, Remote Switch, Red Flex Ribbon (Tape) Reset H Kit, Switch, Black Egg Reset w/ Hook/Loop 1 1 Adhesive Back Fastener & Attaching Screws (EGSBLK) C NLA NLA - Virtual Service Modem Kit 1 1 C,D Cable, Virtual Service, Charger/Modem 1 1 C NLA NLA - Virtual Service Software Kit 1 1 C,E NLA NLA - Disk, 3.5 H.D. Floppy with V.S. Software 1 1 C,E NLA NLA - Adaptor, Null Modem 1 1 C,E NLA NLA - Service Manual - V.S. Software Kit 1 1 C,E Cable, Virtual Service, Charger/Modem 1 1 C NLA NLA - Printer and Interface 1 1 C,F NLA NLA - Paper, Printer 1 1 C,F NLA NLA - Harness, Printer Wiring 1 1 NOTE: A - RII retro controller after 4/30/00 and RII joystick # are direct replacements for joystick/controller # B - Remote Programmer # with the dual connectors (3-Pin and 5-Pin) is the only programmer functionable with the new RII joystick # C - Not Shown D - Part may be ordered individually or is included in the "Virtual Service Modem Kit." E - Part may be ordered individually or is included in the "Virtual Service Software Kit." F - Part may be ordered individually or is included in the "Printer and Interface." G - After 4/30/00 H - Not Shown. After 5/23/04 the Egg Reset Switch became available as a service part and can be used as a direct replacement for the tape reset switch part #

125 MKIV Sip-N-Puff/ Digital Interface 124

126 MKIV Sip-N-Puff/ Digital Interface Item Number Note Part Number Description SNP4M On Chair Off Chair Quantity Per Package Assembly NLA NLA - Sip-N-Puff w/ Digital Interface A,B Kit, SNP/DI, MK5 SAC, 4WSB, S4WSB, GTAM, 1 1 AUX12M6, AUX34M6 Mtg. Hdwr. 1 Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes NLA - Screw, Hex Head (1/4-20 x 1-1/8") Screw, Phillips Pan Head (#4-40 x 3/8") Plate, Mounting 1 1 NOTE: A - Includes items 1-5 B - As of 5/22/07 the Mounting Plate holes and the orientation of the Hardware was revised to attach the electronics closer to the chair. The Mounting Hardware Kit is backward compatible. 125

127 COM12 and COM34 126

128 Item Number Note Part Number Description COM12 and COM34 Quantity Per Package Assembly 6 C See Note See Footnote NLA NLA - Module, Communication, COM34/AUX A,B Kit, COM12/AUX12 and COM34/AUX34 Mounting 1 1 Hardware 1 Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes NLA - Screw, Hex Head (1/4-20 x 1-1/8") NLA - Fastener, Dual Lock Hook and Loop 1 1 Adhesive (2" W x 12" L) 5 Plate, COM12/AUX12 and COM34/AUX34 Mounting 1 1 NOTE: A - Item 4 Screw # was replaced with 4" long adhesive loop fastener 7/1/97. B - Includes Items 1-5 C - Part is no longer serviceable in the field. 127

129 MKIV Displays 128

130 Item Number Note Part Number Description MKIV Displays Quantity Per Package Assembly NLA NLA - Display without Switches Display with Switches A Tube, Flex with Screws NLA NLA - Package, Screw, Phillips Pan Head (#4-40 x 1 4 3/8") 5 B NLA NLA - Hardware, Joystick Tube Mounting Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Joystick Mounting, Black X004-NLA NLA - Screw, Hex Head (1/4-20 x 1-1/8") C Clamp, Fixed Height Joystick Tube D Switch, Red Flex Ribbon (Tape) Reset E Kit, Switch, Black Egg Reset w/ Hook/Loop 1 1 Adhesive Back Fastener & Attaching Screws (EGSBLK) Clamp, Height Adjustable Joystick Tube (ARM250) 1 1 NOTE: A - Includes the Flex Tube and item 4 B - Before 10/4/00 and includes items 6-10 C - After 10/3/00 and can be used as a direct replacement for the Joystick Tube Mounting Hardware part number in the field D - Before 5/24/04 E - After 5/23/04 the Egg Reset Switch replaced the Red Flex Ribbon (Tape) Reset Switch 129

131 MKIV Joystick Options 130

132 Item Number Note Part Number Description 1 N A B C D E O F G H 42 I 43 J MKIV Joystick Options Quantity Per Package Assembly See Note See Footnote NLA NLA - Clamp, Universal Swivel X000 Handle, Lock, Chrome X000 Locknut (1/4-20) NLA NLA - Joystick Tube with Plug Button Assembly Plug Button, Black (7/8") Joystick, Attendant Control (1552M) NLA NLA - Joystick, Heavy Duty Kit, Straight Joystick Tube with Hardware Screw, Phillips Round Head (#10-32 x 3/8") Plug Button, Black (7/8") Hardware, Rear Cane Mount (1673/RCM) Plug Button, Black (7/8") Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Upright, Black -Right NLA NLA - Tube, Joystick Screw w/ Washer (#10 x 7/8") Tube, Arm Mount with Plug Button, Black Plug Button, Black (7/8") NLA NLA - Joystick, MKIV Dual/Compact Hardware, Dual/Compact Joystick Clamp Mounting Clamp Screw, Socket Button Head (#10-32 x 5/16") NLA NLA - Clamp, Mounting NLA NLA - Screw, Socket Head (#10-24 x 1/2") NLA NLA - Spacer, Split (3/8" I.D.) NLA NLA - Chin Cup Assembly Cup, Chin NLA NLA - Screw, Adaptor X000 Screw, Set Socket Cup Point (#8-32 x 1/4") NLA NLA - Touchpad, Joystick Assembly Kit, Straight Joystick Tube with Hardware Plug Button, Black (7/8") Screw, Phillips Pan Head (#4-40 x 3/8") NLA NLA - Hardware, Joystick Tube Mounting Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Joystick Mounting, Black X004-NLA NLA - Screw, Hex Head (1/4-20 x 1-1/8") Clamp, Fixed Height Joystick Tube Switch, Red Flex Ribbon (Tape) Reset Kit, Switch, Black Egg Reset w/ Hook/Loop 1 1 Adhesive Back Fastener & Attaching Screws (EGSBLK) 131

133 Item Number Note Part Number Description 44 NOTE: MKIV Joystick Options Quantity Per Package Assembly Clamp, Height Adjustable Joystick Tube (ARM250) 1 1 K NLA NLA - Display without Switches 1 1 L Display with Switches 1 1 A - Includes the joystick tube and items 10 and 11 B - Includes items C - For On-Chair model numbers 1678 and Includes the joystick tube and item 19 D - Includes items E - Includes items F - Includes the joystick tube, items 33 and 34 G - Before 10/4/00 and includes items H - After 10/3/00. Individual components are non-saleable. Can be used as a direct replacement in the field for the Joystick Tube Mounting Hardware part number I - Before 5/24/04 J - After 5/23/04. The Egg Reset Switch replaced the Red Flex Ribbon (Tape) Reset Switch K - Not Shown and used with the Remote Joystick L - Not Shown and used with the Heavy Duty and Touch Pad Joystick N - No longer available as a service part in the field. O - Part # is no longer available as a service part individually. Order item #27 as a replacement. 132

134 Tash and Therafin Accessories 133

135 Item Number Note Part Number Description Tash and Therafin Accessories Quantity Per Package Assembly 1 P5820-NLA NLA - Switch, Red Soft P5821 NLA - Switch, Green Soft C P5018-NLA NLA - Wafer Board (5018) C P5026-NLA NLA - Star Control C P5020 Mini Joystick with Push (5020) P4337-NLA NLA - Multi-Ability Cable P4353-NLA NLA - CA5 Multi-Connector Box P5970-NLA NLA - Clamp, "U" 1 1 B Bib Assembly (PKG32669) 1 1 B P21456-NLA NLA - Adaptor Clamp - Tash 1 1 B P21457 Adaptor Clamp - Invacare 1 1 B P21460 Midline Swingway System 1 1 A,B Sip-N-Puff, 16" Fixed (PKG32666) 1 1 Includes: (3) Air Tube Straws, (2) Saliva Traps, Tubing, Pivot Shaft/Flexible Metal Gooseneck Assembly, and Extruded Figure "8" Clamp to fit 7/8" Wheelchair Frame Tubing. Extruded Back Cane Adapter Clamp. B Display with Switches 1 1 NOTE: A - See items included. B - Not Shown C - Must be used with display with switches part #

136 Headrest Extension (9110L) (For Non-Recliners Only) Item #1 - Headrest Upholstery NOTE: Chair Width Nylon Vinyl 14" W NLA NLA See Note(s) A 16" W NLA NLA See Note(s) A 18" W NLA NLA See Note(s) A 20" W NLA NLA See Note(s) A A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." 135

137 Item Number Note Part Number Description Headrest Extension (9110L) (For Non-Recliners Only) Quantity Per Package Assembly See Chart #1 - Headrest Upholstery Plug Button, Black (7/8") NLA NLA - Tube, Headrest Extension NLA NLA - Tube, Insert Bracket, Headrest, Black - Right Bracket, Headrest, Black - Left Screw, Phillips Pan Head Tap (#10-32 x 1/2") Screws with Washers (#10-16 x 7/8") Screw w/ Washer (#10 x 7/8")

138 Oxygen Holder Assembly Item Number Note Part Number Description NOTE: Quantity Per Package Assembly Oxygen Holder Assembly Kit NLA NLA - Screw, Hex Head (1/4-20 x 2-1/4") NLA NLA - Screw, Hex Head (1/4-20 x 2") Locknut (1/4-20) Knob, Clamping, Black Decal, Oxygen Warning - English Pad, Non Skid 1 1 A,B NLA NLA - Instruction Sheet, Oxygen Holder 1 1 A NLA NLA - Carton, Shipper 1 1 A - Not Shown B - Item is no longer available from the Invacare Service Parts Department. Refer to the Invacare Website under "Product Literature Search". Enter the part number in the "Keywords" field and download a free PDF version copy. 137

139 Power Wheelchair Tool Kit 138

140 Item Number Note Part Number Description NLA Power Wheelchair Tool Kit NLA - Kit, Power Wheelchair Tool Includes: 1 ea. Multimeter with Leads 1 ea. Locator, Protractor/Angle Magnetic Base 1 ea. Instructions, MKIV Programmer 1 ea. Wire, Grounding with Hand Strap and Clip 1 ea. Leads, 1" Test 1 ea. Light, Pen with Invacare Logo 1 ea. Tape Measure, Compact with Invacare Logo 1 ea. Screwdriver, Pen-Size Phillips/Flat Head 1 ea. Cable, Virtual Service Charger/Modem Quantity Per Package Assembly

141 Item Number Note Part Number Description NOTE: Quantity Per Package Assembly NL NLA - Pocket, Carrying, Nylon (14" W Chair) 1 1 A Pocket, Carrying, Nylon (16-20" W Chair) 1 1 A NL NLA - Pocket, Carrying, Expanded Vinyl (14" W 1 1 A Chair) A Pocket, Carrying, Expanded Vinyl (16-20" W Chair) Extension Handle Assembly, Clutch (Pair) Wheel Lock Extension Handle Assembly, Black (6") Wheel Lock Extension Handle Assembly, Black (8") Strap, Positioning, Seat/Chest w/ Airline Style 1 1 Buckle (Eyelet to Eyelet Length 46") Strap, Positioning, Seat/Chest w/ Auto Style Push 1 1 Button Buckle (Eyelet to Eyelet Length 48") Strap, Positioning, Seat/Chest w/ Hook and Loop 1 1 Style Buckle (Eyelet to Eyelet Length 45") 40176X010 Pump, Tire 1 1 A - Specify upholstery color when ordering. See page titled "Frame Finishes, Touch-Up Paints and Upholstery Colors." NOTE: These items are not shown. Miscellaneous Accessories 140

142 Warranty Replacement Parts NOTE: Part Number Description QTY per Assembly WARR RPLMT - Charger, Battery, E Amp. 115vac (Off Board) Single Mode Round Plug w/ AC 1 See Note(s) A Power Line Cord, CTE Corp. A - See "Battery Charger & Harnesses" Category for more information. 141

143 Invacare Corporation One Invacare Way Elyria, Oh USA Technical Support Customer Service Customer Service Invacare Corporation. All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from Invacare. Trademarks are identified by and. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted. (Revised 3/2/17)