Installation Instructions: Subaru STI Dry Sump Set-Up Kit
|
|
- Brent Gregory
- 6 years ago
- Views:
Transcription
1 Warning: It has come to our attention that the use of a non-oem crankshaft and/or crankshaft pulley (damper) may interfere with the installation of the Cosworth Dry Sump Set-Up Kit for Subaru EJ25 engines (p/n ). It is important to ensure that there is clearance between the face of the crankshaft snout and the small diameter rear face of the Cosworth pump drive hub. If the crankshaft snout is longer than that of an OEM crankshaft, it will prevent the crank pulley bolt from properly securing the OEM damper to the crankshaft. Serious engine damage may occur. Prior to permanent installation, mock up the crankshaft drive pulley assembly and check clearance. The crankshaft damper should be securely clamped between the large diameter rear face of the Cosworth pump drive hub and the face of the timing belt drive pulley. Some aftermarket crankshafts have been found to have a longer than OEM snout, preventing the Cosworth drive pulley from properly clamping the damper. If this is the case, do not continue with the installation. The crankshaft will need to be modified to ensure proper fitment of the Cosworth Dry Sump Set-Up Kit.
2 Part Number: Applications: Subaru STI EJ25 (2.5L) Disclaimer To properly install this part, you MUST have access to a genuine Subaru factory service manual. The installation of these parts on a vehicle intended for use on public streets or highways may violate laws and regulations relating to motor vehicle safety standards or emission regulations. Additionally, these parts are sold as is, without warranty of any kind whatsoever, expressed or implied, (including all warranties of merchantability or fitness for a particular purpose). The installation of these parts could also void vehicle warranty coverage. For your own safety DO NOT use this product unless suitable high speed rated tires, suspension and brake modifications have been fitted. 1. Disclaimer 2. Parts List 3. Parts Diagram 4. Installation 5. Recommendations Index
3 Parts List ITEM # QTY. DESCRIPTION COSWORTH PART # 1 1 Bolt M8x1.25 x 80 SCH PP Washer M8 PR Idler Idler Spacer Washer M8 Thick Nut M8 Hex PP Crankshaft bolt Bolt 4-40 UNC x FHCS Crank Drive Gear Plate Crank Drive Gear Key 5mm Square 6mm length Pump Bracket AN Fitting -12 Male Flare to -12 Male O-ring Bolt ¼-20 UNC x1 SCH PP Scavenge Pump Scavenge Pump Gear 36 Tooth (comes with set screw) Bolt M10x1.5x40 SCH Belt 8mm Pitch 720mm Vacuum Regulator Vacuum Regulator to Oil Fill Flange Adaptor Bolt M6x1.0x12 SCH O-ring 25.1mm ID x 1.6 sec PP Dry Sump Pan Bolt M6x1.0x16 SCH PP Dry Sump Pan Windage Tray Bolt M5x0.8x10 BHCS PP Washer M5 PP AN Fitting -12 Male Flare to -12 Male Screen O-ring 22mm ID x 2.0 sec PR O-ring Large
4 (14) (13) (12) (17) (15) (16) (18) (30) (10) (9) (11) (19) (21) (7) (8) (26) (27) (25) (22) (20) (1) (2) (3) (4) (29) (5) (6) (23) (24) (28)
5 Installation Notes Congratulations on your purchase of Cosworth s Subaru STI Dry Sump Set-Up Kit. This kit is designed to ensure your engine receives sufficient oiling during high G load situations. This kit features a custom dual stage rotor-style scavenge pump, -AN fittings, and an array of bespoke billet parts that have been designed and manufactured in-house in Torrance, CA. It is recommended that this dry sump set-up kit be installed by a professional engine builder. Cosworth dry sump oiling set-up kits are intended for racing applications only and are not intended for use on street operated or emissions controlled vehicles. Be sure to use Loctite 242 (Blue) or equivalent on all hardware. The components of this dry sump oiling kit are designed to bolt on to factory mounting locations. Therefore, the assembly procedures and torque specifications depicted in your Subaru factory service manual must be followed. Pre-installation Due to the fact that you will need to remove your air conditioning pump, it is necessary to have your air conditioning system evacuated by a professional. After the air conditioning system has been evacuated, remove the air conditioning pump following the steps outlined in the factory service manual. For 2008 and newer vehicles, the A/C compressor bracket and A/C belt tensioner assembly must be replaced with equivalent parts from a 2007 model year STI. For 2006 and newer vehicles, the air injection pump must be removed following the Subaru factory service manual. The air pump inlet ports at the rear of the cylinder heads must be blocked off. We recommend Cosworth Air Pump Delete Kit (P/N ). It is also recommended that the OEM oil pump be replaced. While the OEM pump will work with this kit, it will not provide optimal oil delivery. We recommend either the Cosworth High Volume/Pressure Blueprinted Oil Pump (P/N ) or Cosworth 08+ STI High Pressure Blueprinted Oil Pump (P/N ), depending on application.
6 Pump Drive Gear Installation Remove the radiator cooling fans in order to make room in front of the crankshaft pulley. Remove the crankshaft pulley bolt. Hold the crankshaft with either the factory Subaru crank pulley wrench or with an appropriate flywheel locking tool. Attach the crankshaft drive adapter guide plate to the adapter with the five screws. Torque to 5 in-lb with blue Loctite. Ensure the 5mm square key is securely installed into the Cosworth crankshaft drive adapter. Install the crankshaft drive adapter, aligning the 5mm key with the keyway in the OEM crank pulley. Attach the crankshaft drive adapter to the crankshaft pulley using the supplied bolt. Torque to 133 ft-lb. Scavenge Pump Installation Ensure that the O-rings are in place on the mating surface of the scavenge pump. Attach the scavenge pump to the pump bracket using the four PP0213 screws. Torque to 6 ft-lb with blue Loctite. Attach the dry sump bracket to the A/C compressor bracket using the three screws. Torque to 29 ft-lb with blue Loctite. Lubricate o-rings with clean engine oil and install two -12AN male to 1 1/16-12 male adapters to the dry sump bracket. Ensure the pump drive key is securely installed in the slot on the scavenge pump drive shaft. Slide the pump drive gear onto the shaft until the face is flush with end of the pump shaft. Tighten the four set screws on the gear. Dry Sump Pan Installation Drain the engine oil. Remove the factory oil pan following the steps in the Subaru factory service manual. After the pan has been removed, clean off all of the excess sealant on the mounting face of the crankcase. Lubricate o-ring with clean engine oil and install -12AN male to 1 1/16-12 male adapter in the bottom of the dry sump pan. Lubricate o-rings with clean engine oil and install both -12AN male to 1 1/16-12 male screen adapters to the side of the dry sump pan. Bolt the baffle plate into the dry sump pan using the six PP4256 washers and six PP3307 bolts. Torque to 48 in-lb using blue Loctite. Fit the large o-ring into the groove on the dry sump pan. Place the PR mm o-ring in the oil pickup o-ring groove. Bolt the pan to the crankcase using the 14 PP1395 M6 bolts. Torque these bolts to 4.7 ft-lb using blue Loctite.
7 Crankcase Ventilation Remove the factory positive crankcase ventilation hoses and Y-pipe. The hoses originate from the cam covers and are the front most of the two adjacent hoses on each side. Remove the hoses from the nipples and replace them with the supplied rubber caps. One rubber cap will be needed for each of the two cam covers as well as one for the turbo inlet tube PCV inlet. The rear most hoses are balance hoses and are to remain attached. Remove the oil fill neck tube. Install the PP2355 o-ring on to the oil fill neck adapter fitting and lubricate with clean engine oil. Bolt on the oil fill neck adapter to the LH cam cover using the two screws. Torque to 4.7 ft-lb using blue Loctite. Lubricate the o-ring with clean engine oil and install the vacuum regulator into the oil fill neck adapter. Tensioner Assembly Some OEM Subaru parts will be combined with Cosworth supplied parts to complete the tensioner assembly. Again, if your vehicle is 2008 or newer, you will need to purchase parts separately from a certified Subaru parts dealer. Assemble the tensioner as shown below. Install the factory tensioner arm to the A/C compressor bracket using the two stock mounting bolts. Torque the mounting hardware to 18 ft-lb.
8 Stock Subaru Tensioner Bolt Stock Subaru Tensioner Bracket PP5650 PP Stock Subaru Tensioner Slide PR6577 PP5650 Install the dry sump drive belt onto the crankshaft adapter, and then on to the scavenge pump pulley. Use the Subaru factory slide to move the idler pulley into the desired position. Tighten the tensioner assembly through-bolt PP5650 to 18 ft-lb. The drive belt does not require tension like a v-belt does. The idler should be used to take up any excess slack in the belt and ensure appropriate wrap around the sprockets, but there should not be any tension on the belt.
9 Plumbing and Tank Recommendations The oil tank (not included) may be mounted anywhere in the vehicle. Ideally, the oil tank should be mounted as low as possible. Be sure to check the oil level in the tank with the car running at idle to verify the correct volume of oil. This will vary depending on the size and shape of your tank. Follow the routing diagram shown below. It is recommended that hard line be run under the vehicle if the tank is mounted in the rear of the car. At the top of the tank there is an outlet for crankcase vapor. This must be routed to a breather can (not included). Front of Engine -12 AN (-12) Scavenge Pump Scavenge Out Breather Out -16 AN Scavenge In -12 AN -12 AN Pressure In Note: If the engine will go for an extended period of time without running, it is possible for oil to migrate from the oil tank into the sump. It is necessary to scavenge the engine prior to start up to avoid potential engine damage. This can be done by removing the drive belt and spinning the pump by hand until the sump is dry. Verify that there is no standing oil in the sump by checking the oil tank level.
10 Disclaimer A vehicle modified with Cosworth competition and or racing performance products will not meet the legal requirements for operation on public roads and highways. It is the purchaser s responsibility to check and comply with all local, state and federal laws prior to operating vehicle. Installation and use of performance products may also affect and void warranty and insurance policies. In general, Cosworth Performance Parts carry no warranty. Cosworth, LLC and Cosworth Ltd. shall not be liable for direct, indirect, incidental or consequential damage or injury to persons or property that might be claimed as a result from the installation, improper installation, and failure of part including claims for delay, loss of profits or labor. There are no warranties expressed or implied. Warranty In general, Cosworth competition and/or performance parts carry no warranty. Cosworth LLC and Cosworth Limited shall not be liable for direct, indirect, incidental or consequential damage or injury to persons or property that might be claimed as result from the installation or improper installation and failure of part, including claims for delay, loss of profits or labor. There are no warranties expressed or implied.
Installation Instructions: VQ35DE Fuel Rail System
Part Number: KK3905 Applications: 2003-06 Nissan 350Z all & 2003-06 Infiniti G35 (VQ35DE and Rev Up engines) Disclaimer and Warranty A vehicle modified with Cosworth competition and or racing performance
More informationInstallation Instructions: Subaru CS600 & CS600X Long Block Block Assemblies
Part Number: 20000160, 20000161, 20000162, 20002503, 20002504, 20002505, 20002506, 20003488, 20003489, 20003490, 20007211, 20007212, 20007213, 20007705, 20007706, 20007707, 20007708, 20007709, 20007710,
More informationInstallation Instructions: VQ35DE Twin Plenum
Part Number: 20000063 Applications: 2003-07 Nissan 350Z all & 2003-07 Infiniti G35 all Disclaimer and Warranty A vehicle modified with Cosworth competition and or racing performance products will not meet
More informationInstallation Instructions: Mitsubishi 4B11 Stroker Kit
Part Number: 20007783 Applications: Mitsubishi 4B11 EVO X (2.2L) Disclaimer and Warranty A vehicle modified with Cosworth competition and or racing performance products will not meet the legal requirements
More informationInstallation Instructions for Part #: KPS01 - KPS07 Karcepts A/C & P/S Removal Kit (With Alternator Relocation)
Installation Instructions for Part #: KPS01 - KPS07 Karcepts A/C & P/S Removal Kit (With Alternator Relocation) This kit provides the SOLUTION for eliminating the air conditioning compressor and power
More informationPerformer RPM Camshaft/Lifters/Lube Kit CATALOG #7106 MODEL: c.i.d. Ford V8
Performer RPM Camshaft/Lifters/Lube Kit MODEL: 352-428 c.i.d. Ford V8 PLEASE study these instructions carefully before installing your new camshaft. If you have any questions or problems, do not hesitate
More informationApplication / Price Guide 2007 v1
Application / Price Guide 2007 v1 CNC Ported Big Valve Cylinder Heads Retail Note KK3670 Subaru WRX STI EJ25 (2.5L) Pr. 3,849.00 KK3671 Nissan VQ35 (3.5L) Pr. 4,289.00 KK3672 Mitsubishi Evo VIII 4G63 (2.0L)
More informationPerformer-Plus Camshaft/Lifters/Lube Kit Part #2182 For 351-Windsor Ford V8 Engines Installation Instructions
Performer-Plus Camshaft/Lifters/Lube Kit For 351-Windsor Ford V8 Engines Installation Instructions PLEASE study these instructions carefully before installing your new camshaft. If you have any questions
More informationCOLD AIR INTAKE SYSTEM, CIVIC Si,
COLD AIR INTAKE SYSTEM, CIVIC Si, 2012+ 343-05-0200 PLEASE READ CAREFULLY BEFORE PROCEEDING WITH INSTALL Parts list (Please verify all parts are included in the kit before proceeding with installation)
More informationFRONT DRIVELINE MODIFICATION MAY BE NECESSARY!!!!
INSTALLATION INSTRUCTIONS FOR 2009 DODGE 2500/3500 4WD & 1500 Mega Cab 6 SUSPENSION SYSTEM PART NUMBER 7206 Requires the following parts (sold separately) for a complete installation: Front Coil Spring
More informationPERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7112 MODEL: c.i.d. Oldsmobile V8, 1967 & later
PERFORMER RPM Camshaft/Lifters/Lube Kit MODEL: 330-350-403 c.i.d. Oldsmobile V8, 1967 & later PLEASE study these instructions carefully before installing your new camshaft. If you have any questions or
More informationDODGE CUMMINS DUAL PUMP & DELUXE DUAL PUMP KIT
SUBJECT: DODGE CUMMINS DUAL PUMP & DELUXE DUAL PUMP KIT Page 1 of 10 FITMENT: 2003 2007 Dodge Cummins with 5.9L KIT P/N: FPE-DPK-59-NP-[BK,BL,OG,RD], FPE-DPK-59-NP-DX [BK,BL,OG,RD], FPE-DPK-59-3K-[BK,BL,OG,RD],
More informationInstallation Instructions for Part #: KIM01 K20A/A2/A3/Z1 Throttle Body To RBC/RRB/RBB Intake Manifold Adapter
Installation Instructions for Part #: KIM01 K20A/A2/A3/Z1 Throttle Body To RBC/RRB/RBB Intake Manifold Adapter This adapter provides the SOLUTION for directly bolting up a 02-06 RSX-S/ITR or 02-05 Civic
More information1-3/4" or 1-7/8" headers Aftermarket/re-curved distributors
TORKER-PLUS Camshaft/Lifters/Lube Kit #5062 for 1967 & later 396-454 c.i.d. Chevrolet (not for use in 1965-66 396 & 427 engines requiring grooved rear journal) PLEASE study these instructions carefully
More informationFord 7.3L Powerstroke Regulated Fuel Return
Ford 7.3L Powerstroke Regulated Fuel Return ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationDISCLAIMER 1) By installing this product onto your vehicle, you assume all risk and liability associated with its use.
WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing vehicles and cannot be used on
More informationDURAMAX LBZ EGR DELETE
006-007.5 DURAMAX LBZ EGR DELETE ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing
More informationEGR Delete Kit Dodge 6.7L Cummins
I N S TA L L AT I O N GUIDE: EGR Delete Kit 200 202 Dodge 6.7L Cummins ! WARNING: EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY
More informationFord 6.0L Powerstoke Regulated Fuel Return
Ford 6.0L Powerstoke Regulated Fuel Return ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationPERFORMER RPM Camshaft/Lifters/Lube Kit CATALOG #7122 MODEL: c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines)
PERFORMER RPM Camshaft/Lifters/Lube Kit MODEL: 289-302 c.i.d. Ford V8 (not for Boss 302 or 1985 & later roller lifter engines) PLEASE study these instructions carefully before installing your new camshaft.
More information2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009
More informationGENERAL INSTRUCTIONS. PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: c.i.d. Chevrolet V8 Engines CATALOG #2117
Page 1 PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 283-400 c.i.d. Chevrolet V8 Engines GENERAL INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations
More informationL DURAMAX LBZ EGR DELETE GDP TUNING
2006-2007.5 6.6L DURAMAX LBZ EGR DELETE GDP TUNING ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the be used on vehicles that are operated
More informationGM 6.6L DURAMAX LLY EGR DELETE
2004.5-2005 GM 6.6L DURAMAX LLY EGR DELETE ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationPERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 351-M/400 c.i.d. Ford V8 CATALOG #2172 INSTALLATION INSTRUCTIONS
PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT MODEL: 351-M/400 c.i.d. Ford V8 INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new camshaft. If you have any questions
More informationPreassembled Clutch/Electrically Released Brake Module
P-273-2 819-0346 Preassembled Clutch/Electrically Released Brake Module Installation Instructions Contents For These UM Combinations Use These Installation Steps: Introduction...........................
More informationInstallation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *
More informationP/N: OD-AI60. Designed for use on the Ford 6.0L Powerstroke diesel pickup truck
P/N: OD-AI60 Designed for use on the 2003-2007 Ford 6.0L Powerstroke diesel pickup truck NOTE: This intake kit will NOT work on trucks that do not have a factory MAF (Mass Air Flow) sensor! DISCLAIMER
More informationInstant Chat off the main page of Or simply call our tech team at
Subaru WRX/STI Air Oil Separator for Front Mounted Intercooler Setups 2013-02- 22 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More informationINSTALLATION GUIDE: EGR Delete Kit Chevy 6.6L Duramax
INSTALLATION GUIDE: EGR Delete Kit 004.5 005 Chevy 6.6L Duramax ! WARNING: EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for
More informationInstallation Instructions for Part #: KPS03 K20Z3 A/C and P/S Removal Kit
Installation Instructions for Part #: KPS03 K20Z3 A/C and P/S Removal Kit This kit provides the SOLUTION for eliminating air conditioning and power steering on motors found in the 06-08 Civic Si while:
More informationRevised Chevy LS-1 - LS-7 Serpentine Kit. Installation Instructions Kit #20040 (Corvette LS-1, Alternator Only)
Revised -0-09 Chevy LS-1 - LS-7 Serpentine Kit Installation Instructions Kit #20040 (Corvette LS-1, Alternator Only) Parts List NOTE: Kits do not come with Crank Hub Adapter or Alternator. The Crank Hub
More informationGen 2 Portal Gear Hubs for Polaris Ranger Crew 570/900
2753 Michigan Road Madison, Indiana 47250 855-743-3427 INSTALLATION INSTRUCTIONS Gen 2 Portal Gear Hubs for Polaris Ranger Crew 570/900 A Item Description Qty A Rotor 4 B Gear Box, L 2 C Gear Box, R 2
More information(WILL NOT FIT VEHICLES WITH X-REAS SUSPENSION)
2003-2016 TOYOTA 4RUNNER/2007-2014 FJ CRUISER 4WD INSTRUCTIONS 3 SUSPENSION LIFT KIT P/N 40021 (WILL NOT FIT VEHICLES WITH X-REAS SUSPENSION) WARNING!!!! PRODUCT SAFETY LABEL MUST BE INSTALLED INSIDE THE
More informationBMK-30. Heavy-Duty By-Pass Filtration System Installation and Servicing Instructions
BMK-30 Heavy-Duty By-Pass Filtration System Installation and Servicing Instructions IMPORTANT NOTICE Read all instructions completely before attempting to install this unit. Improper installation could
More informationFRONT DRIVELINE MODIFICATION MAY BE NECESSARY!!!!
DODGE 2500/3500 4WD 4.5 SUSPENSION SYSTEM Requires the following parts (sold separately) for a complete installation: Front Coil Spring Box depending on Gas or Diesel/V0: Gas (Hemi) P/N 7004GS Diesel/V0
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-544 2002-2006 NISSAN Sentra SE-R Spec-V L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing
More informationForbidden Diesel Performance Ford 6.7L Powerstroke EGR Delete Instructions 6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE. Page 1
6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE Page 1 WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road
More informationHighly Styled, Low Cost Serpentine Drive Chevy Small Block Alternator & Power Steering Kit #21085 and 21090
Revised 4-2-08 Highly Styled, Low Cost Serpentine Drive Installation Instructions Chevy Small Block Alternator & Power Steering Kit #21085 and 21090 Included Parts List Hardware Qty P/N... Description
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8207 2005 DODGE Durango V8-5.7L See * NOTE 2004 DODGE Durango V8-5.7L C.A.R.B. E.O. # D-670 * NOTE: Legal in
More informationALL AMERICAN BILLET. Front Drive System - Small Block Ford Installation Instructions
ALL AMERICAN BILLET Front Drive System - Small Block Ford Installation Instructions Small Block Ford with AC & PS All American Billet Store (800) 764-0926 www.allamericanbilletstore.com Items needed for
More informationHighly Styled, Low Cost Serpentine Drive
Revised --12 Highly Styled, Low Cost Serpentine Drive Installation Instructions Ford 1 Cleveland Kit #040 (Chrome Alternator and Power Steering) Kit #0460 (Billet Alternator and Power Steering) Included
More informationSteeda S197 Mustang Whipple Supercharger Drive
Steeda S197 Mustang Whipple Supercharger Drive Parts List Qty. Description 1 Whipple supercharger snout 1 Whipple snout collar 1 10-rib supercharger pulley 1 10-rib crank pulley 1 10-rib belt tensioner
More informationEGR Kit w/ Intake Chevy 6.6L Duramax
I N S TA L L AT I O N GUIDE: EGR Kit w/ Intake 004.5 005 Chevy 6.6L Duramax ! WARNING: EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal
More informationDESCRIPTION MECHANICAL FUEL PUMP FUEL FILTER HIGH PRESSURE (35-90 PSI) HIGH PRESSURE (35-90 PSI) (STEEL/INCLUDED)
Edelbrock EFI Universal Fuel Sump System - Adjustable Part #36031, 36032, 36033, 36034 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. This installation
More informationPARTIAL ENGINE ASSY (2TR FE)
COMPONENTS 147 1421Z01 Clip Hood Subassy x9 Radiator Support to Frame Seal LH 30 (306, 22) 30 (306, 22) Fan and Generator V Belt 5.0 (51, 44 in. lbf) Fan Shroud Fan Pulley Fan w/ Fluid Coupling PRE RUNNER
More informationAEROMOTIVE Part # Subaru Fuel Rails for Top Feed Injectors WRX & STI INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 14135 Subaru Fuel Rails for Top Feed Injectors 02-14 WRX & 07-14 STI INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems
More informationComplete Holley Mid-Mount Accessory Drive Kit
Complete Holley Mid-Mount Accessory Drive Kit Part Numbers: 20-181, 20-181BK, 20-181P, 20-182, 20-182BK, 20-182P, 20-191, 20-191BK, 20-191P, 20-192, 20-192BK, 20-192P, 20-201, 20-201BK, 20-201P, 20-202,
More informationINSTALLATION INSTRUCTIONS FOR 2016 TOYOTA TACOMA 4 X 4 AND PRE RUNNER 3 SUSPENSION LIFT KIT PART NUMBER
INSTALLATION INSTRUCTIONS FOR 2016 TOYOTA TACOMA 4 X 4 AND PRE RUNNER 3 SUSPENSION LIFT KIT PART NUMBER 427 WARNING!!! READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE PROCEEDING. MAKE SURE THAT YOU HAVE ALL
More information2000 Nissan Altima SE
Removal 1. Release fuel pressure. See FUEL PRESSURE RELEASE. Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses,
More informationTable of Contents. 1. Safety Consideration and Warnings... Page Title Page... Page Remove Engine From Crate... Page 4
Table of Contents 1. Safety Consideration and Warnings... Page 2 2. Title Page... Page 3 3. Remove Engine From Crate... Page 4 4. Prepare Engine For Race Kit Installation... Page 6 5. Top End... Page12
More informationHighly Styled, Low Cost Serpentine Drive
Revised 11-12-08 Highly Styled, Low Cost Serpentine Drive Installation Instructions Chrysler 18, 40 and 60 Kit #4040 (without Power Steering) 69" Belt Kit #40440 (with Remote Power Steering) 80" Belt Kit
More informationEdelbrock E-Force RPM Carburetor Supercharger Chevrolet LS Engines
Carburetors and air cleaner sold separately. Edelbrock E-Force RPM Carburetor Supercharger Chevrolet LS Engines Rectangular Port Heads: 1511, 15111, 15113 Cathedral Port Heads: 1512, 15121, 15123 Page
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationDESCRIPTION AND OPERATION
303-01B-10 Engine 3.0L 303-01B-10 DESCRIPTION AND OPERATION Upper Engine Components G72932 en 303-01B-11 Engine 3.0L 303-01B-11 DESCRIPTION AND OPERATION (Continued) Item Part Number Description 1 9H589
More informationService Parts. Doosan 11.1 L. Engine. Engine Model: Generator Models: 180/200REZX 180/200RZX TP /09
Service Parts Engine Engine Model: Doosan. L Generator Models: 80/00REZX 80/00RZX TP-0 /09 Table of Contents Introduction... Numbering System Significance... Illustrations... How to Find Part Numbers...
More informationHighly Styled, Low Cost Serpentine Drive
Revised 5-4-09 Highly Styled, Low Cost Serpentine Drive Installation Instructions Chevy Small Block Electric Water Pump Bracket Kit #22100 (Billet Alternator & Power SteeringPump) #22105 (Chrome Alternator
More informationHighly Styled, Low Cost Serpentine Drive
Revised 1-17-11 Highly Styled, Low Cost Serpentine Drive Installation Instructions Chrysler 18, 40 and 60 Kit #4040 (without Power Steering) 66.5" Belt Kit #40440 (with Remote Power Steering) 81.5" Belt
More informationREMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove
More informationInstant Chat off the main page of Or simply call our tech team at
02-07 WRX/STI Air Oil Separator for Top Mounted Intercooler Setups 2013-02- 27 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More informationInstallation Instructions for Part #: KIM01 K20A/A2/A3/Z1 Throttle Body To RBC/RRB/RBB Intake Manifold Adapter
Installation Instructions for Part #: KIM01 K20A/A2/A3/Z1 Throttle Body To RBC/RRB/RBB Intake Manifold Adapter This adapter provides the SOLUTION for directly bolting up a 02-06 RSX-S/ITR or 02-05 Civic
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-425 2004-2005 DODGE Neon SRT-4 L4 2.4L SEE * NOTE 2003 DODGE Neon SRT-4 L4 2.4L C.A.R.B. E.O. # D-392-21 * NOTE:
More informationChevy LS-1 - LS-2 Serpentine Kit
Revised 9-8-08 Chevy LS-1 - LS-2 Serpentine Kit Installation Instructions Kit #20065 (Corvette LS-2 with Power Steering) Kit #20075 (Corvette LS-2 without Power Steering) Kit #20085 (LS-1 Motors with Power
More informationINSTALLATION GUIDE: EGR Delete Kit Ford 6.7L Powerstroke`
INSTALLATION GUIDE: EGR Delete Kit 20 203 Ford 6.7L Powerstroke` ! Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing
More informationHighly Styled, Low Cost Serpentine Drive
Revised -28-09 Highly Styled, Low Cost Serpentine Drive Installation Instructions Chevy Big Block Electric Water Pump Bracket Kit #2100 (Billet Alternator & Power SteeringPump) #2105 (Chrome Alternator
More informationThis information covers procedures for replacing the sealant for the crankshaft cover on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 1.2008 216 50 1(17) Sealant Crankshaft Cover, Replacement D16F Sealant Crankshaft Cover, Replacement W2005773
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL SINGLE ALTERNATOR F-350, F-450, F-550, EXCURSION VERSION 7-07 Parts Description Blackbird Wiring Manual Installation Supplement 6.0 Liter
More informationBAKER CRUISE DRIVE TOP COVER BAKER 1.5 OIL PAN
BAKER BAKER CRUISE 1.5 DRIVE OIL TOP PAN COVER PN: BD-1.5B Wrinkle Black Highlighted Pan Assembly BD-1.5CVO Granite Highlighted Pan Assembly CVO Models BD-1.5P Show Polished Pan Assembly BD-1.5C Chrome
More informationAEROMOTIVE Part # Subaru STI Fuel Rail Kit INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 14137 04-06 Subaru STI Fuel Rail Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend
More informationFord 7.3L SuperDuty Cold Air Intake
999.5-2003 Ford 7.3L SuperDuty Cold Air Intake ! DISCLAIMER ) By installing this product onto your vehicle, you assume all risk and liability associated with its use. 2) It is your responsibility to make
More informationPreassembled Clutch/Brake Module
Preassembled Clutch/Brake Module P-273-1-WE 819-0343 Installation Instructions An Altra Industrial Motion Company Contents MountingtoaMotor...3 Mounting to a Reducer.............3 Installing the Base Mount...........4
More informationHighly Styled, Low Cost Serpentine Drive
Revised 1-30-2012 Highly Styled, Low Cost Serpentine Drive Installation Instructions Chevy Small Block Alternator & Power Steering Kit #21185 and 21190 Style Track Kit #21085 and 21090 Revolver Included
More informationOIL PAN with DRAG RACE BAFFLING P/N
OIL PAN with DRAG RACE BAFFLING P/N 302-22 Instruction Sheet 199R11161 CONGRATULATIONS on your purchase of a Holley LT Retro-fit Oil Pan! We feel that you have purchased the finest performance oil pan
More informationPERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS
PERFORMER-PLUS CAMSHAFT / LIFTERS / LUBE KIT CATALOG # 2103 MODEL: 400 c.i.d. Chevrolet V8 engines GENERAL INSTRUCTIONS Please study these instructions carefully before you remove your stock camshaft.
More informationEngine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
More informationINSTALLATION INSTRUCTIONS
PERFORMER RPM CAMSHAFT / LIFTERS / LUBE KIT For 343-401 c.i.d. AMC V8 Engines CATALOG # 7132 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most
More informationPARTS LIST INCLUDED IN KIT TORQUE SPECIFICATIONS PRODUCT SAFETY LABEL MUST BE INSTALLED INSIDE CAB IN PLAIN VIEW OF ALL OCCUPANTS.
INSTALLATION INSTRUCTIONS FOR 2010-15 TOYOTA 4RUNNER SR5 AND SPORT (Non-Air Leveling & Non-X-REAS) AND FOR 2010-14 TOYOTA FJ CRUISER 2WD & 4WD 3 SUSPENSION LIFT KIT PART NUMBER 432 WARNING!!! READ AND
More informationPart # PLF Ford F250-F550 4WD Coil Spacer Kit PRO COMP SUSPENSION. Suspension Systems that Work!
2360 Boswell Road Chula Vista, CA 91914 Phone 619.216.1444 Fax 619.216.1474 E-Mail tech@explorerprocomp.com PRO COMP SUSPENSION Suspension Systems that Work! Part # 2005-2008 Ford F250-F550 4WD Coil Spacer
More information1996 Aerostar/Ranger/Explorer
Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch
More information1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder
NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness
More informationLloydz Indian Air Filter w/custom Cover
IMC-215/220-I 8.28.2015 Lloydz Motor Workz 25 railroad Ave PO Box 11 Pine Bush, NY 12566 Lloydz Indian Air Filter w/custom Cover VICTORY/INDIAN WARRANTY POLICY: Lloydz Indian Air Filter is intended for
More information10-RIB BELT SYSTEM UPGRADE INSTALLATION MANUAL
10-RIB BELT SYSTEM UPGRADE INSTALLATION MANUAL 2011-2017 AND UP FORD MUSTANG GT 5.0L COYOTE WHIPPLE SUPERCHARGERS 3292 NORTH WEBER AVE FRESNO, CA 93722 TEL 559.442.1261 FAX 559.442.4153 WWW.WHIPPLESUPERCHARGERS.COM
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8203 2003-2005 DODGE RAM 1500 Pickup V8-5.7L C.A.R.B. E.O. # D-670 2003-2005 DODGE RAM 2500 Pickup V8-5.7L C.A.R.B.
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8304 1991-1995 JEEP Wrangler L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles
More informationAll cores due 30 days after invoice date - no credit after 60 days.
NO WARRANTY STATEMENT High performance parts & products no warranty policy: The purchaser understands and recognizes that high performance diesel products and services sold by INDUSTRIAL INJECTION SERVICE.
More informationS&S. Cycle, Inc. Installation Instructions: Cam Support Plate for 2017-up M8 Models. Instruction
Instruction 0-0 0-0- Version 0 by S&S Cycle, Inc. All rights reserved. Printed in the U.S.A. S&S Cycle, Inc. 0 Cty Hwy G Viola, Wisconsin Phone: 0-- Fax: 0-- Technical Service Phone: 0--TECH () Technical
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More informationFront Drive System - Big Block Ford Installation Instructions
Front Drive System - Big Block Ford Installation Instructions Big Block Ford with AC & with PS All American Billet 23042 N 16th Lane Phoenix, AZ 85027 1-844-BILLET1 (844-245-5381) Items needed for install
More informationFMK265SD F L DIESEL WITH DUAL ALTERNATORS
WITH DUAL ALTERNATORS This kit will NOT work on trucks equipped with adaptive steering. INSTALLATION NOTES 1. Disconnect negative batteries cables. Remove the air duct from the passenger side and the black
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8205 2003-2004 DODGE RAM 1500 Pickup V8-4.7L C.A.R.B. E.O. # D-392-29 * NOTE: Legal in California only for racing
More informationPart # Toyota 4WD 4 Suspension System PRO COMP SUSPENSION. Suspension Systems that Work!
2360 Boswell Road Chula Vista, CA 91914 Phone 619.216.1444 Fax 619.216.1474 E-Mail tech@explorerprocomp.com PRO COMP SUSPENSION Suspension Systems that Work! Part # 86-95 Toyota 4WD 4 Suspension System
More informationEdelbrock EFI Universal Fuel Sump System - Adjustable Part #36031, INSTALLATION INSTRUCTIONS
Edelbrock EFI Universal Fuel Sump System - Adjustable Part #36031, 36032 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. This installation can be
More informationStudebaker Truck 289
an ISO 900:2008 Registered Company Studebaker Truck 289 Compressor/Alternator Kit 5600 8865 Goll St. San Antonio, TX 78266 ph: 20-654-77 fax: 20-654-33 90600 REV A /2/2 INST. STUDEBAKER TRUCK 289 COMP/ALT
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS RIOT DYNA MINIMUM REQUIRED TOOLS: FLAT HEAD SCREWDRIVER 1/2, 9/16, 14mm, 7/8 or 22mm WRENCHES 5/16, 1/2, 9/16 SOCKETS AND RATCHET SNAP RING PILERS 3/16, 1/4, 5/16 ALLEN WRENCH
More informationTRU-TIME ADJUSTABLE CAM GEAR Part Number: BK & BK
TRU-TIME ADJUSTABLE CAM GEAR Part Number: 23-801BK & 23-802BK! WARNING: This installation is not for the mechanically challenged! If you are not mechanically inclined or do not understand the procedure
More informationAT Clutch Major Service Sizes 25, 55, 115
P-1404 819-0324 AT Clutch Major Service Sizes 25, 55, 115 Installation Instructions Contents Introduction............................ 2 Warranty....................... back cover Failure to follow these
More informationPART NUMBER: MINI Cooper S L4-1.6L SEE * NOTE
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-699 2007-2010 MINI Cooper S L4-1.6L SEE * NOTE * NOTE: Legal in California only for racing vehicles which may
More informationPart number SP1305. Maintaining your Cold air intake system: Tools required:
Part number SP1305 2000-03 Honda S2000 4 cyl. 2.0L 2004-06 Honda S2000 4 cyl. 2.2L 1-2 piece cold air intake 1-3 Injen filter (#1014) 1-2 3/4 x 3 silicone step hose (#3040) 1-3 straight hose (#3044) 1-
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS RIOT DYNA MINIMUM REQUIRED TOOLS: FLAT HEAD SCREWDRIVER 1/2, 9/16, 14mm, 7/8 or 22mm WRENCHES 5/16, 1/2, 9/16 SOCKETS AND RATCHET SNAP RING PILERS 3/16, 1/4, 5/16 ALLEN WRENCH
More informationYukon Gear & Axle D60 Hardcore Locking Hub Installation Guide
Yukon Gear & Axle Installation Guide PLEASE READ COMPLETELY BEFORE INSTALLATION Application Guide: YHC70001 D60 35spl - 79-93 Dodge internal flange design - 79-91 GM - 78-97 Ford YHC70002 D60 35spl - 99-04
More information