80g. 10.5mm. Width: Weight: Complex Vacuum Generator with Lightweight, Compact Body and High Vacuum Cycle Vacuum Generator VX Series

Size: px
Start display at page:

Download "80g. 10.5mm. Width: Weight: Complex Vacuum Generator with Lightweight, Compact Body and High Vacuum Cycle Vacuum Generator VX Series"

Transcription

1 EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES Complex Vacuum Generator with Lightweight, Compact Body and High Vacuum Cycle Vacuum Generator Series 188 Lightweight and compact body meeting market needs. Weight: 80g Width: 10.5mm The above is the weight of a tube exhaust type with vacuum pressure sensor. Valve signal Vacuum level 1cycle Time Pursue of faster responsiveness of suction solenoid valve to the extreme realized the high cycle of vacuum system. Two types of valves, Normally closed type and Double solenoid type (vacuum retention type) which is suitable to save energy, are selectable. VQ VZ VN

2 Vacuum Generator Series Vacuum Generator GENERATOR Characteristics Wide variety of combinations enables to meet various applications. External Vacuum Controller for vacuum pump is also available.(p.8). 2 installation methods are selectable. Direct-installation type is to fix the product from side using threads. The other DIN rail type is to install the product on DIN rail. Selection according to the application is possible. Direct-installation type DIN rail type Vacuum switch with visibility improved display, and one with analog output with reasonable price are selectable. There are 2 kinds in vacuum switch with display. One is 2 switch output and the other is analog output type. Connector wire is adopted which makes wiring layout easy. 189 VH VS VU VUM VY VB Max. 10 mounting units in a manifold type. Standard nozzle bore: 05(ø0.5mm), 07(v0.7mm) and 10(ø10mm). Copper alloy free and Low level ozone proof types are available in. No copper alloy on airflow path. HMBR material for seal rubber. Krytox grease is a measure against low ozone concentration and dry air. VM VC VRL VG VK VJ Piping Example Blow-off solenoid valve This valve ensures releasing a work-piece from a vacuum pad securely. Blow-off air is supplied during the power supply to the valve is ON. Suction solenoid valve This valve is to generate vacuum Vacuum switch with display suction. Vacuum level is easily adjusted by checking display. 2 types are available; One is 2 switch output and the other is analog output type. Besides, vacuum switch with analog output only which is reasonably priced is available. Turn the release needle to the right (clockwise) to reduce blow-off air and to the left (counterclockwise) to increase. Preventing foreign substances sucked by a vacuum pad from coming into Compressor regulator Select a regulator which can secure the described pressure and flow rate in the specifications. Vacuum pad

3 Construction Example). - S-D2 (Stand-alone type without vacuum switch) Vacuum port 8 Air supply port 5 Example). - S-D2-D (Stand-alone type with vacuum switch) Vacuum port 8 Air supply port 5 No. Part name 1 Pilot valve for vacuum generation 2 Connector Valve unit 5 unit Silencer element 7 element 8 No. Part name 1 Pilot valve for vacuum generation 2 Connector Valve unit 5 unit Silencer element 7 element 8 9 Vacuum sensor unit EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES 190 Example). - S- -M (Manifold type without vacuum switch) Vacuum port 8 No Part name Pilot valve for vacuum generation Connector Valve unit unit Silencer element element Air supply port Example). - S- -D -M (Manifold type with vacuum switch) Vacuum port 8 No Part name Pilot valve for vacuum generation Connector Valve unit unit Silencer element element Vacuum sensor unit VQ VZ VN Air supply port

4 Vacuum Generator Series Vacuum Generator GENERATOR Model Designation of Stand-Alone Type (Example) Complex Vacuum Generator 1 Vacuum characteristics 2 Nozzle bore Valve unit type Vacuum port Exhaust port 5 Air supply port 8 Vacuum switch 7 Solenoid valve type 10 Material option 9 Installation method 1 Vacuum characteristics Performance Performance Performance High-vacuum type Large-flow type High-vacuum at low air supply pressure type H L E (Rated supply pressure:0.5mpa) (Rated supply pressure:0.5mpa) (Rated supply pressure:0.5mpa) 191 VH VS VU VUM VY VB VM VC VRL VG 2 Nozzle bore Nozzle bore mm mm 1.0mm H type Vacuum level, Suction flow -90.kPa 7l/min(ANR) -9.1kPa 1l/min(ANR) -9.1kPa 2[20]l/min(ANR) L type Vacuum level, Suction flow -.5kPa 12l/min(ANR) -.5kPa 2[22]l/min(ANR) -.5kPa 2l/min(ANR) Valve unit type Valve unit type D Double solenoid type (Vacuum retention type) No code Vacuum (V) port (Applicable tube O.D.) E type Vacuum level, Suction flow -90.kPa l/min(anr) -90.kPa 10.5l/min(ANR) -90.kPa 20[19]l/min(ANR) Air consumption 11.5l/min(ANR) (8l/min(ANR)) 2l/min(ANR) (17l/min(ANR)) l/min(anr) (l/min(anr)) 1. Supply pressure is 0.5MPa for H and L type and 0.5MPa for E type. 2. The values in [ ] are for suction flow of tube exhaust type.. Air consumption values in ( ) are for E type.. The values in the table are reference values only. Suction flow varies according to the vacuum system conditions; vacuum port dia. or tube length. are reference values only. Suction flow changes according to the vacuum system conditions; vacuum port dia. or tube length. Tube dia.(mm) ø (Push-In Fitting) ø (Push-In Fitting) Valve unit type Normally closed ø (Push-In Fitting) VK VJ 5 Air supply (PS) port (Applicable tube O.D.) Tube dia.(mm) ø (Push-In Fitting) ø (Push-In Fitting) Exhaust (EX) port S J Exhaust method Silencer vent Tube exhaust (ømm Push-In Fitting). Tube exhaust is not selectable for nozzle bore ø1mm of L (Large-flow type).

5 EXTERNAL GENERATOR CONTROLLER PAD 7 Solenoid valve type Voltage D2 DC2V A100 AC100V ACCESSORIES 8 Vacuum switch Switch DW Pressure sensor with display (2 switch outputs) No code Without vacuum switch 9 Installation method DA Switch Pressure sensor with display (Analog and switch output) A0 Switch Analog output pressure sensor (No ) D Installation method DIN rail type No code Installation method Direct-installation type Material option Material Exhaust method No code -S Standard No copper alloy & HNBR seal Silencer vent & Tube exhaust Tube exhaust. -S specification is only for where air flow through but not corresponding to electrical parts, wires or vacuum port size with ømm. VQ VZ VN

6 Vacuum Generator Series Vacuum Generator GENERATOR Model Designation of Manifold Type (Example) Complex Vacuum Generator 1 Vacuum characteristics 2 Nozzle bore Valve unit type Vacuum (V) port (Applicable tube O.D.) Exhaust (EX) port 8 Vacuum switch 7 Solenoid valve type 5 Air supply (PS) port (Applicable tube O.D.) 9 No. of stations 10 Material option 1 Vacuum characteristics Performance Performance Performance H High-vacuum type Large-flow type High-vacuum at low air supply pressure type L E (Rated supply pressure:0.5mpa) (Rated supply pressure:0.5mpa) (Rated supply pressure:0.5mpa) K When different vacuum characteristics are mixed (Fill in the details on Specification order form) 19 VH VS VU VUM VY VB VM VC VRL 2 Nozzle bore Nozzle H type L type E type bore Vacuum level, Suction flow Vacuum level, Suction flow Vacuum level, Suction flow Air consumption mm -90.kPa -.5kPa -90.kPa 11.5l/min(ANR) 7l/min(ANR) 12l/min(ANR) l/min(anr) (8l/min(ANR)) mm -9.1kPa -.5kPa -90.kPa 2l/min(ANR) 1l/min(ANR) 2[22]l/min(ANR) 10.5l/min(ANR) (17l/min(ANR)) mm -9.1kPa -.5kPa -90.kPa l/min(anr) 2[20]l/min(ANR) 2l/min(ANR) 20[19]l/min(ANR) (l/min(anr)) 00 When different vacuum characteristics are mixed (Fill in the details on Specification order form) 1. Supply pressure is 0.5MPa for H and L type and 0.5MPa for E type. 2. The values in [ ] are for suction flow of tube exhaust type.. Air consumption values in ( ) are for E type.. The values in the table are reference values only. Suction flow varies according to the vacuum system conditions; vacuum port dia. or tube length. are reference values only. Suction flow changes according to the vacuum system conditions; vacuum port dia. or tube length. Valve unit type D K Valve unit type Double solenoid type (Vacuum retention type) No code Valve unit type Normally closed When different valves are mixed on a manifold (Fill in the details on Specification order form) VG VK VJ Vacuum (V) port (Applicable tube O.D.) Tube dia.(mm) ø (Push-In Fitting) ø (Push-In Fitting) ø (Push-In Fitting) 0 When different ports are mixed on a manifold (Fill in the details on Specification order form) 5 Air supply (PS) port (Applicable tube O.D.) Tube dia.(mm) ø (Push-In Fitting) ø (Push-In Fitting) 8 ø8 (Push-In Fitting) 1 ø10 (Push-In Fitting) Exhaust (EX) port (Applicable tube O.D.) S Exhaust Tube exhaust Silencer vent method (ømm Push-In Fitting) 8 Tube exhaust (ø8mm Push-In Fitting) 1 Tube exhaust (ø10mm Push-In Fitting)

7 EXTERNAL GENERATOR CONTROLLER PAD 7 Solenoid valve type Voltage D2 DC2V A100 AC100V ACCESSORIES 8 Vacuum switch Switch DW Pressure sensor with display (two switch outputs) No code Without vacuum switch 9 No. of stations DA Switch Pressure sensor with display (analog and switch output) A0 Switch Analog output pressure sensor (no ) No. of manifold Material option Material Exhaust method No code -S Standard Copper alloy free Silencer vent & Tube exhaust Tube exhaust. -S specification is only for where air flow through but not corresponding to electrical parts, wires or vacuum port size with ømm. 1. When simultaneous operation of all mounting units is required, contact us in advance. 2. When 10 or more stations on a unit are required, contact PISCO in advance. VQ VZ VN

8 Vacuum Generator Series Vacuum Generator GENERATOR Model Designation of Manifold-base only (Example) Manifold-base for High-cycle type vacuum generator 1 Air supply (PS) port (Applicable tube O.D.) 1 Air supply port Tube dia.(mm) ø (Push-In Fitting) ø (Push-In Fitting) No. of stations Material option 2 Exhaust (EX) port (Applicable tube O.D.) 8 ø8 (Push-In Fitting) 1 ø10 (Push-In Fitting) 2 Exhaust port S Exhaust method Silencer vent Tube exhaust (ømm Push-In Fitting) 8 Tube exhaust (ø8mm Push-In Fitting) 1 Tube exhaust (ø10mm Push-In Fitting) No. of stations No. of manifold VH VS VU VUM VY VB VM VC VRL VG VK VJ Material option Material Exhaust method Specification Order Form Example of Manifold type Vacuum Vacuum Nozzle Valve Vacuum Air supply Exhaust Solenoid Vacuum characteristics bore unit type (V) port (PS)port (EX) port) valve type switch generator type L St. 1 St. 2 St. 8 St. St. St. no. St. 5 St. St. 7 St. 9 R St. 10 Manifold Type Example L side No code -S Standard Silencer vent & Tube exhaust Copper alloy free & HNBR seal Tube exhaust No. of stations 9 Material option 10 Air supply (PS) port Station no. is arranged St.1, St.2 St.10 from L side. Vacuum (V) port St.1 St.2 St.St. Exhaust (EX) port R side

9 Model Designation of Manifold Installation Top-Mounting Unit alone (Example) High-cycle type vacuum generator 1 Vacuum characteristics 2 Nozzle bore Nozzle bore mm 2 Nozzle bore Valve unit type Vacuum (V) port Vacuum switch 5 Solenoid valve type 1 Vacuum characteristics Performance Performance High-vacuum type Large-flow type H L E (Rated supply pressure:0.5mpa) (Rated supply pressure:0.5mpa) H type L type Vacuum level, Suction flow Vacuum level, Suction flow -90.kPa -.5kPa 7[7]l/min(ANR) 12[12]l/min(ANR) mm 1.0mm -9.1kPa -9.1kPa -.5kPa -.5kPa 1[1]l/min(ANR) 27[20]l/min(ANR) 2[22]l/min(ANR) 2l/min(ANR) 1. Supply pressure is 0.5MPa for H and L type and 0.5MPa for E type. 2. The values in [ ] are for suction flow of tube exhaust type.. Air consumption values in ( ) are for E type. E type Vacuum level, Suction flow -90.kPa []l/min(anr) -90.kPa 10.5[10.5]l/min(ANR) -90.kPa 20[19]l/min(ANR) 7 Material option Performance High-vacuum at low air supply pressure type (Rated supply pressure:0.5mpa) Air consumption 11.5l/min(ANR) (8l/min(ANR)) 2l/min(ANR) (17l/min(ANR)) l/min(anr) (l/min(anr)) EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES 19 Valve unit type D Valve unit type Double solenoid type (Vacuum retention type) No code Valve unit type Normally closed Vacuum (V) port Tube dia.(mm) ø (Push-In Fitting) ø (Push-In Fitting) ø (Push-In Fitting) 5 Solenoid valve type Voltage D2 DC2V A100 AC100V Vacuum switch Switch DW Pressure sensor with display (two switch outputs) No code Without vacuum switchvacuum switch DA Switch Pressure sensor with display (analog and switch output) A0 Switch Analog output pressure sensor (no ) 7 Material option No code -S Material Standard Copper alloy free & HNBR seal. -S specification is only for where air flow through but not corresponding to electrical parts, wires or vacuum port size with ømm. VQ VZ VN

10 L St. 1 St. 2 Vacuum Generator Series Vacuum Generator GENERATOR Vacuum Generator Series Specification Order Form To: NIHON PISCO CO., Ltd. Name : Order No. : Date : Requested EX-W PISCO Date : Quantity : Vacuum Vacuum Nozzle Valve Vacuum Air supply Exhaust Solenoid Vacuum characteristics bore unit type (V) port (PS)port (EX) port) valve type switch generator type No. of stations 9 Material option VH VS VU VUM VY St. no. St. St. St. 5 St. St. 7 St. 8 St. 9 R St Refer to the example on page 195 to fill in the form. 2. Copy this page and use.. Use this specification order form for different specifications of mounting units.. -S specification is not selectable for silencer exhaust type and a type with vacuum port size with ømm. VB VM VC VRL VG VK VJ

11 How double solenoid type works 1 When suction pilot valve is OFF (At vacuum generation suspended) Connector Sensor unit EXTERNAL GENERATOR CONTROLLER Valve unit Air supply port unit 2 When suction pilot valve is ON (At vacuum generating) Vacuum port element Silencer element PAD ACCESSORIES ON Vacuum air Supply air When suction pilot valve is OFF (At vacuum retention) OFF Exhaust air 198 Vacuum air Supply air Exhaust air When blow-off pilot valve is ON (At vacuum generation suspended and supply of blow-off air) ON Blow-off air VQ Supply air VZ VN

12 Vacuum Generator Series Vacuum Generator GENERATOR How normally closed type works 1 When suction pilot valve is OFF (At vacuum generation suspended) Connector Sensor unit Valve unit Air supply port unit Vacuum port element Silencer element 2 When suction pilot valve is ON (At vacuum generation) ON Vacuum air 199 VH VS VU Supply air When suction pilot valve is OFF (At vacuum generation suspended) OFF Exhaust air VUM VY VB VM VC Supply air VRL When blow-off pilot valve is ON (At supply of blow-off air) VG VK ON VJ Blow-off air Supply air

13 Specification (Supply pressure) Fluid medium Operating pressure range characteristics Nozzle bore Model code (mm) Air 0. ~ 0.7 MPa Operating temp. range 5 ~ 50 C Protective structure H05 L05 E05 H07 L07 S L07 J E07 H10 S H10 J L10 S E10 S E10 J Silencer vent & Tube exhaust Silencer vent & Tube exhaust Silencer vent & Tube exhaust Silencer vent & Tube exhaust Silencer vent Tube exhaust Silencer vent & Tube exhaust Silencer vent Tube exhaust Silencer vent Silencer vent Tube exhaust Rated supply pressure (MPa) IEC standard IP0 equiv. Final vacuum ( kpa) Suction flow (l/min(anr)) ( ) 22 ( ) ( ) 20 ( ) 2 ( ) 20 ( ) 19 ( ) Air consumption (l/min(anr)) The specifications are different from those of other conventional PISCO vacuum generator series. The values in the table are reference values only. Suction flow changes according to the vacuum system conditions; vacuum port dia. or tube length. are reference values only. Suction flow changes according to the vacuum system conditions; vacuum port dia. or tube length. Solenoid valve specification ( / Blow-off solenoid valve) Pilot valves Item Suction solenoid valve Blow-off solenoid valve Operation system Pilot valve Valve construction Elastic seal, Poppet valve Rated voltage DC2V AC100V DC2V AC100V Allowable voltage range DC2V ±10% AC100V ±10% DC2V ±10% AC100V ±10% Surge protection circuit Surge absorber Diode bridge Surge absorber Diode bridge Power consumption 1.2W (With ) 1.5VA (With ) 1.2W (With ) 1.5VA (With ) Manual operation Push button (Non-lock) Operation indicator Coil excitation: Red ON Connector type (Cable length:500mm) Wire connection method Red:DC2V Blue Red:DC2V Black:COM Black:COM Blue Changeover valve Item Suction solenoid valve Operation system Pneumatic operation by pilot valve Valve construction Elastic seal, Poppet valve Proof pressure 1.05MPa Valve type Normally closed / Double solenoid Lubrication Not required Effective sectional area Air supply port (PS) size ømm:.5mm 2 Air supply port (PS) size ømm:.5mm 2 Response time ( ) Normally closed / Vacuum generation(off ON): 7m sec, Vacuum operation stop (ON OFF): 1m sec Double solenoid / Vacuum generation(off ON): 7m sec, Vacuum operation stop (ON OFF): 9m sec Response time is the time length until pressure change at vacuum port is detected under rated supply pressure and rated voltage. Vacuum arrival time and blow-off time at the piping end (work-piece) vary according to ejector characteristics, volume (tube length), blow-off air rate and others EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES 200 VQ VZ VN

14 Vacuum Generator Series Vacuum Generator GENERATOR 201 VH VS VU VUM VY VB VM VC VRL VG VK VJ Vacuum switch Specification Factory default pressure -50kPa(SW1) -10kPa(SW2) -50kPa Current consumption Pressure detection Operating pressure range Pressure setting range Proof pressure Operating temp. range Operating humidity range 0mA or less Diffused semiconduction pressure switch -100 ~ 0kPa -99 ~ 0kPa 0.2MPa 0 ~ 50 C (No freezing) 5 ~ 85%RH (No dew condensation) 15mA or less Power requirements Protective structure No. of pressure setting 2 12 ~ 2VDC ± 10% Ripple (P-P) 10% max. IEC standard IP0 equiv 1 Operating accuracy ±%F.S. max. (at Ta=25 C) Differential response Fixed (2%F.S. max.) Variable (About 0-15% of setting value) Switch output NPN open collector output: 0V 80mA max. Residual voltage 0.8V max. Analog output Display Display frequency Indication accuracy Sensor resolution Operation indicator Function Blow-off air rate Vacuum switch with display Vacuum switch without display 2 switch output (-DW) Analog output & 1 switch output (-DA) Analog output only (-A0) Output voltage Zero-point voltage Span voltage 1 ~ 5V 1±0.1V ±0.1V Output current 1mA max. (Load resistance: 5kΩ max.) LIN/HYS ±0.5%F.S. max. 0 ~ -99kPa (2-digit red display) About times / sec ±%F.S. ±2 digit 1 digit SW1: Red turns ON when pressure is above setting. Red turns ON when SW2: Green turns ON when pressure is above setting. pressure is above setting. 1. MODE switch (ME / S1 / S2) 1. MODE switch (ME / SW) 2. S1 setting trimmer (2/-rotation trimmer) 2. SW setting trimmer (2/-rotation trimmer). S2 setting trimmer (2/-rotation trimmer). HYS setting trimmer (About 0-15% of setting value) Vacuum characteristics Stand-alone type & DIN rail type Manifold type H05 0 ~ 9.5l/min[ANR] 0 ~ 8.0l/min[ANR] H07 0 ~ 8.5l/min[ANR] 0 ~.0l/min[ANR] H10 0 ~.5l/min[ANR] 0 ~ 5.0l/min[ANR] L05 0 ~ 9.0l/min[ANR] 0 ~ 7.0l/min[ANR] L07 0 ~ 7.0l/min[ANR] 0 ~ 5.5l/min[ANR] L10 0 ~.5l/min[ANR] 0 ~.5l/min[ANR] E05 0 ~ 9.5l/min[ANR] 0 ~ 8.0l/min[ANR] E07 0 ~ 9.0l/min[ANR] 0 ~ 7.0l/min[ANR] E10 0 ~ 7.5l/min[ANR] 0 ~ 5.5l/min[ANR] D(Double solenoid) 0.2 ~ 2l/min[ANR].The above value is 0.5Mpa of supply pressure.

15 Specification Characteristics Final vacuum (kpa) 100 Element material H05, L05, E05 Vacuum characteristics E type Final vacuum H type Final vacuum L type Final vacuum H type suction flow E type suction flow Air consumption L type suction flow Supply pressure (MPa) Flow rate (l/min(anr)) Flow characteristics Vacuum pressure (kpa) H type E type Supply pressure:0.5mpa (H, L type) 0.5MPa (E type) L type Suction flow (l/min(anr)) H07, L07, E07 Vacuum characteristics Final vacuum (kpa) PVF (Polyvinyl formal) ing capacity 10µm area 502mm 2 Replacement element model code V010B0 Supply pressure - Final vacuum, Suction Flow, Air Consumption E type Final vacuum H type Final vacuum L type Final vacuum Air consumption L type suction flow Supply pressure (MPa) H type suction flow 10 E type suction flow Flow rate (l/min(anr)) Flow characteristics Vacuum pressure (kpa) Supply pressure:0.5mpa (H, L type) 0.5MPa (E type) H type E type L type (Silencer vent) L type (Tube exhaust) Suction flow (l/min(anr)) EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES H10 - J, E10 - J Vacuum characteristics Final vacuum (kpa) E type Final vacuum H type Final vacuum Air consumption E type suction flow (Tube exhaust) H type suction flow (Tube exhaust) Supply pressure (MPa) Flow rate (l/min(anr)) Flow characteristics Vacuum pressure (kpa) Supply pressure:0.5mpa (H type) 0.5MPa (E type) E type (Silencer vent) H type (Tube exhaust) E type (Tube exhaust) H type (Silencer vent) Suction flow (l/min(anr)) Stand-Alone Type Weight List H10 - S, L10 - S, E10 - S Vacuum characteristics Final vacuum (kpa) E type Final vacuum L type Final vacuum H type Final vacuum Air consumption L type suction flow (φ Silencer vent) L type suction flow (φ Silencer vent) H type suction flow(silencer vent) E type suction flow (Silencer vent) Supply pressure (MPa) Flow rate (l/min(anr)) Flow characteristics Vacuum pressure (kpa) E type (Tube exhaust) Supply pressure:0.5mpa (H type) 0.5MPa (E type) E type (Silencer vent) H type (Tube exhaust) H type (Silencer vent) L type Suction flow (l/min(anr)) 202 Model code - S- -D - J- -D - S- -A0 - J- -A0 - S- - J- 1. Add 5g for DIN rail type to the above weights. Manifold Type Weight List Model code - S- -D -M02 Unit combinations Silencer vent & with display Tube exhaust & with display Silencer vent & analog output pressure sensor Tube exhaust & analog output pressure sensor Silencer vent without vacuum pressure sensor Tube exhaust without vacuum pressure sensor Mounting unit combinations Silencer vent & with display & 2 manifolds - - -D -M02 Tube exhaust & with display & 2 manifolds Weight(g) Weight(g) Add 90g / station 2. The above table represents the weight of pressure sensor with display type. Pressure sensor with analog output type (no indicator) is g/station lighter than the above weights and no vacuum pressure sensor type is 10g/station lighter than the above weights. VQ VZ VN

16 Vacuum Generator Series Vacuum Generator GENERATOR How to insert and disconnect 1. How to insert and disconnect tubes 1 Tube insertion Insert a tube into Push-In Fitting of the vacuum generator up to the tube end. Lock-claws bite the tube to fix it and the elastic sleeve seals around the tube. Refer to 2. Instructions for Tube Insertion under Common Safety Instructions for Fittings. 2 Tube disconnection The tube is disconnected by pushing release-ring to release Lock-claws. Make sure to stop air supply before the tube disconnection. 2. How to fix the product 1 Direct-installation type Tighten M threads through the fixing holes on the resin body with tightening torque 0. to 0.5Nm. Refer to the outer dimensional drawings for the hole pitch. 20 VH VS VU VUM VY VB 2 DIN rail type Mount the product on a DIN rail and tighten DIN rail fixing screw with tightening torque Nm using a proper Phillips screwdriver. When shaking or physical impact on DIN rail is expected, attach commercialized metal stoppers on both sides to fix Din rail. VM VC VRL VG VK VJ Applicable Tube and Related Products Polyurethane Tube (Piping products catalog P.59) Vacuum Pads Polyurethane Tube is for the general pneumatic piping and suitable for a compact piping. Nylon Tube (Piping products catalog P.08) Nylon Tube is for the general pneumatic piping and suitable for a high-pressure fluid up to 1.5MPa (NB tube: 1.0MPa). Vacuum Tube (Piping products catalog P.12) Vacuum Tube is a ultra-soft tube and suitable for piping of vacuum generators or actuators. Vacuum Pad Standard Series P.28 Vacuum Pad Sponge Series P.8 Vacuum Pad Bellows Series P.88 Vacuum Pad Multi-Bellows Series P.508 Vacuum Pad Oval Series P.52 Vacuum Pad Soft Series P.550 Vacuum Pad Soft Bellows Series P.578 Vacuum Pad Skidproof Series P.0 Vacuum Pad Ultrathin Series P.2 Vacuum Pad Mark-free Series P.2 Vacuum Pad Long Stroke Series P.58

17 Standard Size List Silencer vent, Direct-installation type or DIN rail type without Vacuum pressure sensor Normally closed type Air supply port (P)s Silencer Double solenoid Silencer vent, Direct-installation type or DIN rail type with 2 switch output with display Normally closed type Air supply port (P) Silencer Double solenoid EXTERNAL GENERATOR CONTROLLER PAD Type Air supply port (P)s Page to refer 20 Vacuum port mm mm mm Silencer Air supply port mm mm Exhaust port With silencer Type Air supply port (P) Page to refer 207 Vacuum port mm mm mm Silencer Air supply port mm mm Exhaust port With silencer ACCESSORIES Silencer vent, Direct-installation type or DIN rail type with switch output and analog output sensor with display Normally closed type Silencer vent, Direct-installation type or DIN rail type with analog output sensor Normally closed type Air supply port (P) Silencer Air supply port (P) Silencer 20 Double solenoid Double solenoid Air supply port (P) Silencer Air supply port (P) Silencer Type Page to refer 208 Vacuum port mm mm mm Air supply port mm mm Exhaust port With silencer Type Page to refer 209 Vacuum port mm mm mm Air supply port mm mm Exhaust port With silencer VQ VZ VN

18 Vacuum Generator Series Vacuum Generator GENERATOR Tube exhaust, Direct-installation type or DIN rail type without vacuum pressure sensor Normally closed Tube exhaust, Direct-installation type or DIN rail type with 2 switch output with display Normally closed Exhaust port (EX port) Copper alloy free Selectable Exhaust port (EX port) Copper alloy free Selectable Double solenoid Double solenoid Exhaust port (EX port) Exhaust port (EX port) Type Page to refer 210 Vacuum port mm mm mm Air supply port mm mm Exhaust port mm Type Page to refer 211 Vacuum Air supply port port mm mm mm mm mm Exhaust port mm Tube exhaust, Direct-installation type or DIN rail type with switch output sensor and analog output with display Normally closed Tube exhaust, Direct-installation type or DIN rail type with analog output sensor Normally closed 205 VH VS VU Double solenoid Exhaust port (EX port) Copper alloy free Selectable Double solenoid Exhaust port (EX port) Copper alloy free Selectable VUM VY Exhaust port (EX port) Exhaust port (EX port) VB VM VC VRL VG Type Page to refer 212 Vacuum Air supply port port mm mm mm mm mm Exhaust port mm Type Page to refer 21 Vacuum Air supply port port mm mm mm mm mm Exhaust port mm VK VJ

19 LOCK RELEASE Silencer vent, Direct-installation type Model code: (D)- S- -- EXTERNAL GENERATOR CONTROLLER ød (Air supply port (P)) ø EX C2 C1 L2 L (Needle stroke) ød () 2 1 EX PAD ACCESSORIES Silencer vent, DIN rail type -- Model code: (D)- S- -D DIN rail 20 ød (Air supply port (P)) DIN rail Common dimension list on this page ( ) ( ).2 ( ) Applicable tube O.D.(øD). ( ) EX C2 EX C1 5.5 L L (Needle stroke) C1 C2 L1 L2 L ød () DIN rail fixing screw ( ).7 ( )2.7 ( ) marked length is the value with DIN rail height 7.5mm. Unit:mm CAD file name Common circuit diagram on this page - S- (-D)(Normally closed type) type D- S- (-D)(Double solenoid type) type VQ Silencer Silencer VZ VN Characteristic chart page -- CAD data is available at PISCO website.

20 S2 S2 LOCK RELEASE Vacuum Generator Series Vacuum Generator GENERATOR Silencer vent, pressure sensor of 2 switch output with display, Direct-installation type Model code: (D)- S- -DW with display MODE SW1 SW2 -- kpa ME S1 MODE switch SW1 Pressure setting trimmer ø. SW2 Pressure setting trimmer ød () ød (Air supply port (P)) EX C2 C1 L2 L (Needle stroke) Silencer vent, pressure sensor of 2 switch output with display, DIN rail type Model code: (D)- S- -DW-D MODE SW1 SW2.5 with display 2 1 EX VH VS kpa ME S1 MODE switch DIN rail SW1 Pressure setting trimmer SW2 Pressure setting trimmer VU VUM VY VB VM VC VRL VG VK VJ ød (Air supply port (P)) DIN rail Common dimension list on this page ( ) ( ).2 ( ) Applicable tube O.D.(øD) Common circuit diagram on this page - S- -DW(-D)(Normally closed type) type. ( )5.2 ød () ( ).7 ( )2.7 D- S- -DW(-D)(Double solenoid type) type DIN rail fixing screw EX C2 EX C1 5.5 L L (Needle stroke) ( ) marked length is the value with DIN rail height 7.5mm. Unit:mm C1 C2 CAD file name L1 L2 L Silencer Silencer Characteristic chart page -- CAD data is available at PISCO website.

21 ME SW ME SW LOCK RELEASE Silencer vent, Pressure sensor with switch output and analog output with display, Direct-installation type Model code: (D)- S- -DA ød (Air supply port (P)) with display kpa MODE MODE switch Pressure setting trimmer ø. SW HYS Hysteresis setting trimmer EX C2 C1 L2 L (Needle stroke) 58.5 ød () 2 1 Silencer vent, Pressure sensor with switch output and analog output with display, DIN rail type Model code: (D)- S- -DA-D with display EX EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES MODE SW HYS DIN rail MODE switch Pressure setting trimmer kpa Hysteresis setting trimmer 208 ød (Air supply port (P)) DIN rail ( ) Common dimension list on this page ( ).2 ( ) EX C2 C1 5.5 L L (Needle stroke) Applicable tube O.D.(øD) C1 C2 L1 L2 L ( )5.2 Unit:mm CAD file name ød () DIN rail fixing screw ( ).7 ( )2.7 EX ( ) marked length is the value with DIN rail height 7.5mm. Common circuit diagram on this page - S- -DA(-D)(Normally closed type) D- S- -DA(-D)(Double solenoid type) VQ Silencer Silencer VZ VN Characteristic chart page -- CAD data is available at PISCO website.

22 LOCK RELEASE Vacuum Generator Series Vacuum Generator GENERATOR Silencer vent, Pressure sensor with analog output, Direct-installation type Model code: (D)- S- -A0 Pressure sensor (Analog output only) ø ød () ød (Air supply port (P)) C1 L EX C2 L (Needle stroke) EX Silencer vent, Pressure sensor with analog output, DIN rail type Model code: (D)- S- -A0-D Pressure sensor (Analog output only) DIN rail 10.5 VH VS VU VUM VY VB VM VC VRL VG VK VJ ød (Air supply port (P)) DIN rail Common dimension list on this page ( ) ( ).2 ( ) Applicable tube O.D.(øD) Common circuit diagram on this page - S- -AO(-D)(Normally closed type). ( )5.2 ød () ( ).7 ( )2.7 D- S- -AO(-D)(Double solenoid type) DIN rail fixing screw EX C2 EX C1 5.5 L L (Needle stroke) ( ) marked length is the value with DIN rail height 7.5mm. Unit:mm C1 C2 CAD file name L1 L2 L Silencer Silencer Characteristic chart page -- CAD data is available at PISCO website.

23 LOCK RELEASE ød (Air supply port (P)) Tube exhaust, Direct-installation type Model code: (D)- J- Copper alloy free Selectable ø. L2 C C1 L (Needle stroke) ød () 2 1 ø (Exhaust port (EX)) -- When Copper alloy free is selected, add -S at the end of model code. Please note Copper alloy free is not selectable for vacuum port ømm. EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES Tube exhaust, DIN rail type -- Model code: (D)- J- -D Copper alloy free Selectable ød (Air supply port (P)) DIN rail Common dimension list on this page ( ) ( ).2 ( ) Applicable tube O.D.(øD) DIN rail C2 ( )5.2 ød () ( ).7 ( ) L ø (Exhaust port (EX)) C (Needle stroke) L C1 C2 L1 L2 L. DIN rail fixing screw. ( ) marked length is the value with DIN rail height 7.5mm. Unit:mm CAD file name When Copper alloy free is selected, add -S at the end of model code. Please note Copper alloy free is not selectable for vacuum port ømm. 210 Common circuit diagram on this page - J- (-D)(Normally closed) D- J- (-D)(Double solenoid) VQ Exhaust (EX port) Exhaust (EX port) VZ VN Characteristic chart page -- CAD data is available at PISCO website.

24 S2 S2 LOCK RELEASE Vacuum Generator Series Vacuum Generator GENERATOR Tube exhaust, 2 switch output with display, Direct-installation type Model code: (D)- J- -DW Copper alloy free Selectable kpa with display 2-ø. MODE ME S1 MODE switch SW1 Pressure setting trimmer SW1 SW2 SW2 Pressure setting trimmer -- When Copper alloy free is selected, add -S at the end of model code. Please note Copper alloy free is not selectable for vacuum port ømm. 211 VH VS ød (Air supply port (P)) C1 L C2 58 L2 8..5(Needle stroke) Tube exhaust, 2 switch output with display, DIN rail type Model code: (D)- J- -DW-D Copper alloy free Selectable with display MODE SW1 SW2.5 ød () 2 1 ø (Exhaust port (EX)) -- When Copper alloy free is selected, add -S at the end of model code. Please note Copper alloy free is not selectable for vacuum SW2 Pressure setting trimmer kpa ME S1 MODE switch port ømm. DIN rail SW1 Pressure setting trimmer VU VUM VY VB VM VC VRL VG VK VJ ød (Air supply port (P)) DIN rail ( )1.2 Common dimension list on this page 10.5 ( ).2 ( ) Common circuit diagram on this page - J- -DW(-D)(Normally closed type) C2. ( ) L C (Needle stroke) L Unit:mm C1 C2 CAD file name Applicable tube O.D.(øD) L1 L2 L ød () ( ).7 ( )2.7 ø (Exhaust port (EX)) ( ) marked length is the value with DIN rail height 7.5mm. D- J- -DW(-D)(Double solenoid) DIN rail fixing screw Exhaust (EX port) Exhaust (EX port) Characteristic chart page -- CAD data is available at PISCO website.

25 ME SW ME SW LOCK RELEASE Tube exhaust, Pressure sensor with switch output and analog output with display, Direct-installation type Model code: (D)- J- -DA Copper alloy free Selectable ød (Air supply port (P)) kpa MODE MODE switch Pressure setting trimmer C1 L with display 2-ø. SW HYS Pressure setting trimmer C2 58 L2 8..5(Needle stroke) ød () 2 1 Tube exhaust, Pressure sensor with switch output and analog output with display, DIN rail type Model code: (D)- J- -DA-D Copper alloy free Selectable ød (Air supply port (P)) DIN rail ( ) Common dimension list on this page ( ).2 ( )7.5 kpa with display MODE SW MODE switch DIN rail Pressure setting trimmer HYS Hysteresis setting trimmer C2. 約 500 ( )5.2 ø (Exhaust port (EX)) ( ).7 ( )2.7 ød () DIN rail fixing screw L ø (Exhaust port (EX)) C (Needle stroke) ( ) marked length is the value L with DIN rail height 7.5mm Unit:mm C1 C2 CAD file name Applicable tube O.D.(øD) L1 L2 L -- When Copper alloy free is selected, add -S at the end of model code. Please note Copper alloy free is not selectable for vacuum port ømm. -- When Copper alloy free is selected, add -S at the end of model code. Please note Copper alloy free is not selectable for vacuum port ømm. EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES 212 Common circuit diagram on this page - J- -DA(-D)(Normally closed type) D- J- -DA(-D)(Double solenoid) VQ Exhaust (EX port) Exhaust (EX port) VZ VN Characteristic chart page -- CAD data is available at PISCO website.

26 LOCK RELEASE Vacuum Generator Series Vacuum Generator GENERATOR Tube exhaust, Analog output sensor, Direct-installation type Model code: (D)- J- -A0 Copper alloy free Selectable 10.5 with analog output only 2-ø. -- When Copper alloy free is selected, add -S at the end of model code. Please note Copper alloy free is not selectable for vacuum port ømm. 21 VH VS VU VUM VY VB VM VC VRL VG VK VJ ød (Air supply port (P)) Common circuit diagram on this page - J- -AO(-D)(Normally closed type) C C1 L L2 8..5(Needle stroke) Tube exhaust, Analog output sensor, DIN rail type Model code: (D)- J- -A0-D Copper alloy free Selectable ød (Air supply port (P)) DIN rail Common dimension list on this page ( ) ( ).2 ( ) Applicable tube O.D.(øD) DIN rail with analog output only L 2-C (Needle stroke) L C1 C2 L1 L2 L C ( )5.2 Unit:mm CAD file name ød () ø (Exhaust port (EX)) ( ).7 ( )2.7 ( ) marked length is the value with DIN rail height 7.5mm. D- J- -AO(-D)(Double solenoid) ød () DIN rail fixing screw ø (Exhaust port (EX)) -- When Copper alloy free is selected, add -S at the end of model code. Please note Copper alloy free is not selectable for vacuum port ømm. Exhaust (EX port) Exhaust (EX port) Characteristic chart page -- CAD data is available at PISCO website.

27 kpa kpa ME MODE MODE ME S1 SW S2 SW SW1 HYS SW2 -M Tube exhaust, Manifold type Model code M Copper alloy free Selectable 2-øD2(Exhaust port) 70 2-L2 CAD file name.when Copper alloy free is selected, add -S at the end of model code. Please note Copper alloy free is not selectable for vacuum port ømm C øD2(Air supply port) 11 n(n = No. of stations) -.5 Manifold fixing hole ( holes) L2 2-C2 (2.5) C1 L n(n = No. of stations) +11 n(n = No. of stations) ød1(vacuum port) Fixing screw Lock lever -- Unit:mm Applicable tube O.D.(øD1) C1 L1 Applicable tube O.D.(øD2) 8 10 C2 L2 EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES 21 VQ VZ VN -- CAD data is available at PISCO website.

28 kpa kpa ME MODE MODE ME S1 SW S2 SW SW1 HYS SW2 215 Vacuum Generator Series Vacuum Generator GENERATOR VH VS -M Silencer vent, Manifold type Model code - S- - -M CAD file name 70 2-L C øD2(Exhaust port) EX -.5 Manifold fixing hole ( holes) C1 L1 11 n(n = No. of stations) n(n = No. of stations) n(n = No. of stations) ød1(vacuum port) Fixing screw Lock lever -- Unit:mm Applicable tube O.D.(øD1) C1 L1 Applicable tube O.D.(øD2) 8 10 C2 L2 VU VUM VY VB VM VC VRL VG VK VJ -- CAD data is available at PISCO website.

29 Detailed Safety Instructions Before using PISCO products, be sure to read Safety Instructions and Safety Instruction Manual on page 5-9 and Common Safety Instructions for Vacuum Series on page 7-9. Warning 1. The compressed air is dangerous if mishandled. It is recommended that a person having enough knowledge and experience carry out the assembling or maintenance of a machine or a device using pneumatic equipments. 2. At maintenance check of the product, shut electrical power supply and the air supply, and make sure to vent the residual pressure in the air circuit in advance. When installing or removing of a unit to/from a manifold, make sure to shut off air supply and to exhaust the residual pressure in the air circuit first.. The product is not explosive-proof. Do not use it in the environments containing flammable or explosive gases or liquid. Please avoid using in conditions that pressure of 0.1MPa or higher is continuously supplied to vacuum circuit.. The coil in a pilot solenoid valve generates heat under the following 1 to conditions. The heat may cause dropping life cycle, malfunctions, getting burnt or damaging peripheral machines. Contact us when the power is applied to the vacuum generator under the following conditions: 1 The power is continuously ON for over 2 hours. 2 High-cycle operation. Even when intermittent running of the generator is carried out, the total operation time per day is longer than non-operation time. 5. When the electricity is applied to valves continuously for a long time, the coils generate heat. It may cause dropping life cycle, malfunctions, getting burnt or damaging peripheral machines. EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES 21 Caution 1. The product shall be used within the operating pressure range. Otherwise, there are risks of damage or deformation. 2. Regarding double-solenoid types ( D- ), the switchover valve (main valve) is placed in neutral after the supply of pilot air has been suspended (the same is true when the valve is being operated for the first time after shipment). When resuming the supply of pilot air, be sure to send a signal to the pilot valve, or conduct switchover operations manually as required.. The increase of of manifold station may cause troubles such as performance drop by a shortage of air supply and insufficient capability to exhaust, and exhaust air leak to the vacuum port. Allowable station numbers of simultaneous operation differs by nozzle size, vacuum performance, and other conditions. Please contact us for details.. Although the exhaust of the model with a manifold type is silencer vent by each individual unit, the exhaust air of operating unit or blow-off air flows into the vacuum port of non-operating unit. If such exhaust air causes the problem, please contact PISCO. VQ VZ VN

30 ME SW S2 Vacuum Generator Series Vacuum Generator GENERATOR Safety Rules for Use Vacuum Switch with display (1) Pressure Setting Method 1 Turn on the power (Make sure the correct wiring and apply DC power to the vacuum switch). 2-1 Set the indicator switch at Pressure Setting Mode (ME S1 / S2 and SW) 2-2 (Vacuum switch with analog output) Fully turn the hysteresis setting trimmer (HYS) in the counterclockwise direction in order to minimize the hysteresis adjustment in advance. Adjust the pressure adjusting trimmer (S1 / S2 and SW) with a flathead screwdriver to set at the desired value. Set the indicator switch at ME and apply pressure and check the actual operation. (Vacuum switch with 2 switch output) Switch output 1 (S1): Red turns ON at the pressure with more than the setting. Switch output 2 (S2): Green turns ON at the pressure with more than the setting. (Vacuum switch with analog output) Switch output (SW): Red turns ON at the pressure with more than the setting. 217 VH VS VU (2) Differential response setting 1 Differential response setting can be adjusted by the hysteresis setting trimmer (HYS). 2 Differential response setting range is regulated within about 0-15% of the set value. Differential response setting becomes large when the trimmer is turned in the clockwise direction. Confirmation of Hysteresis Gradually increase and decrease the supply pressure around the set pressure value and read the value by a vacuum gauge when operation indicator lamp turns ON/OFF. The difference in the displayed values is taken as differential response. Hysteresis adjustment is useful for the following cases: I ncrease differential response when pressure pulsates with output repeatedly showing small on/off movements. When an allowable range is to be set for the lowering of pressure. VUM VY display display VB VM VC VRL kpa MODE switch MODE SW HYS Hysteresis setting trimmer Pressure setting trimmer with display (Analog output and 1 switch output) kpa MODE switch MODE ME S1 SW1 SW2 SW2 Pressure setting trimmer SW1 Pressure setting trimmer with display (2 switch output) VG () Wire Connecting Method VK V+ (Brown) V+ (Brown) V+ (Brown) VJ Load SW OUT (Black) Main circuit ANALOG OUT (Gray) + - Load SW1 OUT (Black) Main circuit Load SW2 OUT (Gray) + - Main circuit ANALOG OUT (Gray) + - COM (Blue) with display (Analog output and 1 switch output) COM (Blue) with display (2 switch output) COM (Blue) Analog output sensor

31 Safety Instructions for Vacuum Switch with display 1 Do not use the vacuum switch in the environment or gasses containing corrosive substance. It may cause a sensor trouble. 2 Wiring or ways by which noise or other disturbance is caused may cause a sensor trouble. Since the sensors are not explosive-proof, do not use them in an inflammable or explosive gas, fluid or atmosphere. Since the sensors are not drip / dust proof, do not use them in locations where they may be exposed to water or oil drops or dust. 5 Do not use the sensor in an atmosphere exceeding the range of application temperature or causing heat as sensor malfunction may result. Make sure to turn off the power before wiring. Check the wire colors, and do not short-circuit output terminals, power supply terminals and COM terminals when wiring. Short-circuits may cause a sensor trouble. 7 Do not give an excessive tensile strength and bending on a lead wire. Otherwise, breaking wire or damage on connector may be caused. 8 Instant application of pressure about 0.5MPa does not affect the sensor performance, but do not keep applying 0.2MPa or more constantly during blow-off air supply. It may be a cause of damaging the sensor. 9 When adjusting pressure and differential response, use a flathead screwdriver (accessory). Do not apply an excessive force on the trimmer and slowly turn it within its rotation limits. Otherwise, there is a risk of damaging the trimmer and the circuit board. 10Supply a stable DC power to the product. 11 Add a surge absorption circuit to relays or solenoid valves, etc. which are to be connected with output terminal and source terminal. Do not apply a current exceeding 80mA. 12 Ground the FG terminal when using a unit power source such as switching current. 1 Output terminals (lead wire color: black and gray) and other terminals should not be short-circuited. 1 Avoid strong external impacts and excessive fore to on the sensor body. EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES 218 Blow-off air adjustment method Turn the blow-off air rate adjustment needle to the right (clockwise) to reduce blow-off air and to the left (counterclockwise) to increase. After the adjustment, tighten the locknut firmly with 0.1 to 0.2Nm of the tightening torque.. Make sure to use a proper flathead screwdriver for the needle adjustment. Locknut Turn left : To increase air rate Blow-off air rate adjustment needle Turn right : To reduce air rate VQ VZ VN

32 Vacuum Generator Series Vacuum Generator GENERATOR How to replace Elements When replacing the filter element, remove the vacuum port piping. Then, loosen the screw inside the joint (at the end of the tube insertion hole) using a Philips type screwdriver( ) with an outside diameter of ø2.5mm or less, and remove the vacuum port. After replacing the filter element, make sure that the filter packing has not been detached, then install the filter element and filter window on the vacuum port, and fasten the port to the main body. For fastening, apply the tightening torque of 0.1 ~ 0.15N m.. Do not let the screw driver touch the Lock-claws. Damage or deformation of the Lock-claws may result in the degradation of the tensile strengh. Phillips-head screw driver element (Model code:v010b0) cover seal rubber 219 VH VS VU Replacement of Silencer Elements When replacing the silencer element of a direct mount type unit, pull out the lock pin using a flat-tip screwdriver and replace the elements. After replacing the element, insert the lock pin correctly. The lock pin is bent for fall-proof. Therefore, please insert the pin in the direction as shown in the right picture. Silencer element Model code:v010b28 Element cap VUM VY VB VM VC VRL VG VK VJ When replacing the silencer element of a DIN rail type unit, remove the screw for fixing the DIN rail, using an appropriate Phillips type screwdriver. Then, remove the fixing pin using a flat-tip screwdriver. After replacing the elements, insert the lock pin correctly to install the screw for fixing the DIN rail. The lock pin is bent for fall-proof. Therefore, please insert the pin in the direction as shown in the right picture. Lock Pin Silencer element Model code:v010b29f(vacuum characteristics:h10, L10, E10, H07, L07) Model code:v010b29d(vacuum characteristics:e07, H05, L05) Silencer element Model code:v010b29f(vacuum characteristics:h10, L10, E10, H07, L07) Model code:v010b29d(vacuum characteristics:e07, H05, L05) Silencer element Model code:v010b28 Element cap Phillips type screwdriver Spring Nut Lock Pin DIN rail fixing screw

33 How to attach / detach and clean the nozzle and diffuser Pull out the diffuser with a pair of long-nose pliers after removing the cover and the diffuser retainer. Use a cushion material such as a sponge to cover the nozzle port to prevent the nozzle from jumping out. Apply the air to the vacuum generator (*5)and the nozzle comes out by the air pressure. Take out the cushion material and then take out the nozzle. Remove any foreign substance from nozzle, inside of diffuser by air blowing or wiping(*). Combine the nozzle with the diffuser and push them back into the body with the attention not to drop the nozzle. Place the diffuser retainer on the diffuser and tighten the cover with Nm of the tightening torque. For installation of the silencer element, refer to the section "How to replace the silencer elements." (*5) <Warning> *During applying the air to the generator, do not point the nozzle port toward anyone. There is a risk of injury by the nozzle jumping out. (*) Do not damage nozzle, diffuser bore, seal rubber and the seal part of the body. It may cause performance drop. EXTERNAL GENERATOR CONTROLLER PAD ACCESSORIES Nozzle Diffuser Fixing screw How to replace Mounting units of Manifold type How to detach a mounting unit Shut off the air supply and exhaust the residual pressure. Turn off the power supply and detach the wiring. Use a proper-sized Phillips screwdriver to remove the fixing screw. Pull out lock lever completely by using a flathead screwdriver and detach the mounting unit. How to install a mounting unit Make sure not to lose O-rings of air supply and exhaust ports. Fully pull out the lock lever and install a mounting unit. While pushing down the mounting units, push the lock lever back to the original position and tighten the fixing screw with Nm of the tightening torque to fix the lock lever. 220 VQ Fixing screw Lock lever VZ VN Phillips screwdriver

34 Vacuum Generator Series Vacuum Generator GENERATOR How to replace Silencer Elements of Manifold Type How to detach a silencer element Tapping screw Remove tapping screws by a Phillips screwdriver. Detach the element cover and replace the silencer elements (Model code: V010B92). How to install silencer element Tighten tapping screws firmly with 0.-0.Nm of the tightening torque with a proper screwdriver. Silencer cover Silencer element (Model code:v010b92) 221 VH VS VU VUM VY VB VM VC VRL VG VK VJ

Vacuum pump system type

Vacuum pump system type type VS*P Vacuum component C O N T E N T S Series variation 166 20 mm width universal type (/M) 168 10.5 mm width universal type (/M) 184 31.5 mm width discrete type (VSQP) 214 11 mm pitch manifold dedicated

More information

Vacuum Switch with LED display

Vacuum Switch with LED display Vacuum Switch with display 812 To improve visibility, an display is adopted for the vacuum switch. displays indicates set-up pressure and working pressure. Two types of vacuum switch selection: Two switch

More information

Related vacuum products

Related vacuum products Vacuum component C O N T E N T S variation 420 Position locking valve () 422 Compact vacuum regulator () 426 Vacuum break unit () 436 Vacuum filter large volume union type (VSFB) 440 Compact vacuum filter

More information

VSG Series Features Descriptions VSG VSG VSG Descriptions Supply valve Descriptions Vacuum filter

VSG Series Features Descriptions VSG VSG VSG Descriptions Supply valve Descriptions Vacuum filter Basic performance oriented general vacuum ejector unit Series Nozzle diameter: ø.5, ø, ø1. acuum switch and vacuum break valve, etc. are unitized, so types matching the work purpose is selectable. Features

More information

External Vacuum Controller with Blow-off Air and Relief Pressure Adjustment. External Vacuum Controller Series

External Vacuum Controller with Blow-off Air and Relief Pressure Adjustment. External Vacuum Controller Series EXTERNAL PAD ACCESSORIES External acuum Controller with Blow-off Air and Relief Pressure Adjustment. External acuum Controller Series 318 XP Pressure adjustment function and blow-off flow adjusting function,

More information

Complex Vacuum Generator with Blow-off Air and Relief Pressure Adjustment

Complex Vacuum Generator with Blow-off Air and Relief Pressure Adjustment ACUUM TERNAL ACUUM GENERATOR CONTROLLER ACUUM PAD ACUUM ACCESSORIES Complex acuum Generator with Blow-off Air and Relief Pressure Adjustment acuum Generator J Series 12 Pressureadjustingfunctionisaddedtotheconventionalblow-off

More information

Pressure Switch with Super slim LED Display

Pressure Switch with Super slim LED Display Pressure Switch with Super slim LED Display 796 Super slim and light weight pressure sensor with a LED display. width: 8.2mm, height: 4.mm, length: 62.2mm, weight: 17g Indicator font size on the LED display

More information

Speed Controller High Flow

Speed Controller High Flow http://www.pisco.co.jp CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Speed Control Valve for High Speed Cylinder High Flow Speed Control Valve for Actuator. High Flow Type with Same Size as. Suitable for

More information

Nozzle diameter: ø0.5, ø0.7, ø1.0, ø1.2. Features

Nozzle diameter: ø0.5, ø0.7, ø1.0, ø1.2. Features ariety of modularized units enable selections of integrated type ejector units suitable for the application. K eries Nozzle diameter: ø0.5, ø0.7, ø1.0, ø1.2 ZM Q G Y H U B C K KM J JM X XM Features acuum

More information

Push-In Fitting Type Quick Exhaust Valve

Push-In Fitting Type Quick Exhaust Valve http://www.pisco.co.jp CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Valve Valve 482 Suitable for High-Speed Cylinder. Standard Valve is equipped with Silencer. Re-adjustment of exhaust

More information

Exhaust Throttle (Needle) Valve ET

Exhaust Throttle (Needle) Valve ET http://www.pisco.co.jp CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Exhaust Throttle (Needle) Valve Exhaust Throttle (Needle) Valve ET 494 Exhaust Throttle (Needle) Valve with Silencer. Directly Connectable

More information

Connector Series. Multiple Push-In Fitting Type. Desorption of Several Tubes at One Time. Combinable Connectors by Connector Band.

Connector Series. Multiple Push-In Fitting Type. Desorption of Several Tubes at One Time. Combinable Connectors by Connector Band. http://www.pisco.co.jp FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Multiple Push-In Fitting Type Connector 4 Desorption of Several Tubes at One Time. Combinable Connectors by Connector Band. Combinable

More information

Pressure Gauge. Fluid admitted Pressure indication range Accuracy Service temperature range Cap. Resin body GPC (1)

Pressure Gauge. Fluid admitted Pressure indication range Accuracy Service temperature range Cap. Resin body GPC (1) Pressure Gauge Feature The compact-size pressure gauges can be installed in small spaces. With the built-in tube fitting type, tube connection is the only necessary step before pressure indication. Graphical

More information

Conventional specification. External Pilot air specification 0 ~ 0.7. Compact, yet keeps large capacity.» Limited space can be utilized.

Conventional specification. External Pilot air specification 0 ~ 0.7. Compact, yet keeps large capacity.» Limited space can be utilized. Compact, yet keeps large capacity.» Limited space can be utilized. Standard.» SVR 10 series takes over the functions (Valve variations) of discontinued SVA 10 series. Pneumatic Symbols 5(R) 5(R) 5(R) 5(R)

More information

Vacuum Equipment. Issued Rev Vacuum Generator. Vacuum Accessories. Vacuum Pad. External Vacuum Controller.

Vacuum Equipment. Issued Rev Vacuum Generator. Vacuum Accessories. Vacuum Pad. External Vacuum Controller. Issued 2009.11 Rev.1 2017.09 Vacuum Generator Simple type Complex type External Vacuum Controller Complex type Vacuum Pad Standard type Sponge type Bellows type (Attachment) Oval type Soft type Skidproof

More information

External vacuum controller

External vacuum controller By newly adding pressure adjusting function to blow-off flow adjusting function, it enables to prevent works from being blown away. A relief mechanism built into the blow-off circuit which breaks the vacuum

More information

Throttle (Needle) Valve PP Series

Throttle (Needle) Valve PP Series http://www.pisco.co.jp CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Flow Control Valve for Clean Environment Throttle (Needle) Valve 466 Copper alloy free material Nongrease Clean-room

More information

Multi-Circuit Rotary Block

Multi-Circuit Rotary Block http://www.pisco.co.jp FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Multi-Circuit Block for Rotating Applications Multi-Circuit Rotary Block 302 Make to Order Suitable for Low-Speed Rotating Applications

More information

Throttle (Needle) Valve Standard Series

Throttle (Needle) Valve Standard Series http://www.pisco.co.jp CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Throttle (Needle) Valve Throttle (Needle) Valve Standard 448 Control Actuator Speed or Pneumatic Signals. Adjustable

More information

SVR10 SVA10. External Pilot air specification. Conventional specification 0 ~ 0.7. Compact, yet keeps large capacity.» Limited space can be utilized.

SVR10 SVA10. External Pilot air specification. Conventional specification 0 ~ 0.7. Compact, yet keeps large capacity.» Limited space can be utilized. Compact, yet keeps large capacity.» Limited space can be utilized. Standard.» SVR 10 series takes over the functions (Valve variations) of discontinued SVA 10 series. Pneumatic Symbols 1(P) 1(P) 1(P) 1(P)

More information

MICRO EJECTORS. Micro ejector single unit (without solenoid valve) ME. Micro ejector with solenoid valve DC24V. Block-off plate ME MA-BP

MICRO EJECTORS. Micro ejector single unit (without solenoid valve) ME. Micro ejector with solenoid valve DC24V. Block-off plate ME MA-BP Micro Ejector Order Codes Manifold Order Codes Micro ejector single unit (without solenoid valve) ME Body model nozzle diameter : Maximum flow rate on vacuum side 03 0.3 : 3.0R/min. [0.012in., 0.106ft.

More information

In-line Filter of Easy Maintenance

In-line Filter of Easy Maintenance http://www.pisco.co.jp AIR PREPARATION ACTUATOR PLARAILCHAIN HARMO ROBOT PARTS In-line Filter of Easy Maintenance 176 Keeping the same usability with vacuum filter VFU Series and usable with positive pressure.

More information

Series ZSE30/ISE30. High Precision, 2-color Display Digital Pressure Switch. With One-touch fittings are newly introduced. PSE

Series ZSE30/ISE30. High Precision, 2-color Display Digital Pressure Switch. With One-touch fittings are newly introduced. PSE High Precision, 2-color Display Digital Pressure Switch Series SE30/ISE30 SE ISE PSE I SE3 PS I SE 1 2 SP ISA2 IS SM PF2 IF Data With One-touch fittings are newly introduced. Straight type Elbow type 16-2-1

More information

MULTISTAGE MICRO EJECTORS

MULTISTAGE MICRO EJECTORS MULTISTAGE MICRO EJECTORS MED07-E, MED10-E Specifications Basic model Item Media Operating pressure range MPa [psi.] Proof pressure MPa [psi.] Operating temperature range (atmosphere and media) C [ F]

More information

Transmitters: Relay Valve VR4151/4152

Transmitters: Relay Valve VR4151/4152 Relay Valve VR4151/4152 Appropriate output sequences are affected according to the signal received from the mechanical valve. VR4151 VR4152 Precautions Be sure to read before handling. Refer to pages 5-11-2

More information

MULTISTAGE MICRO EJECTORS CONTENTS ACCESSORIES GENERAL CATALOG AIR TREATMENT, AUXILIARY, VACUUM, AND FLUORORESIN PRODUCTS. Caution

MULTISTAGE MICRO EJECTORS CONTENTS ACCESSORIES GENERAL CATALOG AIR TREATMENT, AUXILIARY, VACUUM, AND FLUORORESIN PRODUCTS. Caution ACCESSORIES GENERAL CATALOG AIR TREATMENT, AUXILIARY, VACUUM, AND FLUORORESIN PRODUCTS MULTISTAGE MICRO EJECTORS CONTENTS MED07-E, MED10-E Series Specifications 715 Order Codes 716 Operation Principle

More information

Vacuum Generator VN. Vacuum level

Vacuum Generator VN. Vacuum level Perfect for use in an IC chip loader, IC handlers and other semiconductor manufacturing devices. Limited space can be utilized. Stand alone type Small size and lightweight vacuum generator & external vacuum

More information

The valve body is prepared in two different colors enabling the user to opt for either of the two according to operational environment.

The valve body is prepared in two different colors enabling the user to opt for either of the two according to operational environment. SVB series is best suitable for controlling valve direct mount type vacuum generators (VH, VS type) ilot actuated type conventional solenoid valve. This is a standard model designed to combine excellent

More information

2-Color Display High-Precision Digital Pressure Switch

2-Color Display High-Precision Digital Pressure Switch 2-Color Display High-Precision Digital Pressure Switch Series ZSE3/ISE3 2-color digital display allows you to choose the setting according to your application requirements. 4 different display settings

More information

Series ISA. Air Catch Sensor. For Detection of Work Presence

Series ISA. Air Catch Sensor. For Detection of Work Presence ED Bar graph for easy calibration The ED bar graph indicator in conjunction with the adjustment knob for the variable orifice allows for easy and correct calibrations. Over range (Red) Correct range (Green)

More information

Solenoid Valve SVR Series

Solenoid Valve SVR Series http://www.pisco.co.jp SOLENOID AIR VALVE PREPARATION ACTUATOR PLARAILCHAIN HARMO ROBOT PARTS Solenoid Valve for Pneumatic System Solenoid Valve SVR Series 94 Small Body but Secure Large Flow Rate Height

More information

Tube Fitting Stainless SUS316 Series

Tube Fitting Stainless SUS316 Series http://www.pisco.co.jp FITTING CONTROLLER VALVE TUE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type of Corrosion Resistant Steel Tube Fitting SUS316 108 Copper alloy free material Nongrease Clean-room packaging

More information

Non-Contact Sensor for Workpiece Placement Verification

Non-Contact Sensor for Workpiece Placement Verification ir Catch Sensor Series 2 Non-Contact Sensor for Workpiece Placement Verification Stable detection of. to. mm clearance Due to the pneumatic bridge circuit and semiconductor pressure sensor, the non-contact

More information

9.8 mm. Digital Pressure Switch. 3-step setting. RoHScompliant. Series ZSE10(F)/ISE10. Vertical mounting space reduced to approx.! Reduced in depth!

9.8 mm. Digital Pressure Switch. 3-step setting. RoHScompliant. Series ZSE10(F)/ISE10. Vertical mounting space reduced to approx.! Reduced in depth! Digital Pressure Switch Series ZSE1(F)/ISE1 Low profile 26.1mm 9.8 mm 13.5 mm 53.4 mm Reduced in depth! (Actual size) RoHScompliant Vertical mounting space reduced to approx.! 1 2 Position Detection Switch

More information

2-Color Display High-Precision Digital Pressure Switch Series ZSE40A(F)/ISE40A

2-Color Display High-Precision Digital Pressure Switch Series ZSE40A(F)/ISE40A 2-Color Display High-Precision Digital Pressure Switch Series ZSEA(F)/ISEA New M8 connector type RoHS IP65 Applicable fluid Air, Non-corrosive gas, Non-flammable gas Can copy to up to 10 switches simultaneously.

More information

Series ITV0000. Compact Electro-pneumatic Regulator ITV N. IITV00 02 n. How to Order F.R.L. AV AU AF AR IR VEX AMR ITV IC VBA VE VY1 G PPA AL

Series ITV0000. Compact Electro-pneumatic Regulator ITV N. IITV00 02 n. How to Order F.R.L. AV AU AF AR IR VEX AMR ITV IC VBA VE VY1 G PPA AL Compact Electro-pneumatic Regulator Series For single unit and single unit for manifold Pressure range 9 Option. MPa. MPa.9 MPa kpa Option How to Order N Power supply voltage 24 VDC ±% 2 to VDC Option

More information

Series ZQ. Compact Vacuum Ejector. One-touch fitting. Digital vacuum pressure switch With LED display. ZX ZR ZM ZH ZU ZL ZY ZQ ZF ZP ZCU AMJ Misc.

Series ZQ. Compact Vacuum Ejector. One-touch fitting. Digital vacuum pressure switch With LED display. ZX ZR ZM ZH ZU ZL ZY ZQ ZF ZP ZCU AMJ Misc. Compact acuum Ejector Series Body width mm, Weight9 g (Single unit with vacuum pressure switch and suction filter) Conventional 21.mm mm One-touch fitting ZR ZM ZH ZU ZL ZY ZF Z ZCU AMJ Misc. Digital vacuum

More information

Series 10-ZSE40A(F)/10-ISE40A

Series 10-ZSE40A(F)/10-ISE40A Series 10-ZSEA(F)/10-ISEA RoHS 2-Color Display High Precision Digital Pressure Switch How to Order For positive pressure Clean series For vacuum/ compound pressure 01 N01 W1 10 Rated pressure range ISEA

More information

Series VQ Port Solenoid Valve

Series VQ Port Solenoid Valve Port Solenoid Valve Series VQ00 Outstandingly high speed, stable response, and long service life. ON:. ms, OFF: ms, Dispension accuracy ms (; supply pressure 0. MPa) 00 million cycles or more (Factors

More information

Compact Vacuum Ejector

Compact Vacuum Ejector Compact acuum Ejector Series ZA Total length Total width 7.9 mm 9.9 mm Total height. mm Response time 0 ms Response time for up to 0 ka Nozzle diameter: ø0.7 iping: ø/ø. x 0 mm Able to install on the moving

More information

Main Block Series. Concentrated Branching Joint for Assembly. Assembling Manifold Blocks for Concentrated Branching

Main Block Series. Concentrated Branching Joint for Assembly. Assembling Manifold Blocks for Concentrated Branching http://www.pisco.co.jp FITTING CONTROLLER VALVE TUE MAKE-TO-ORDER PRODUCTS Concentrated ranching Joint for Assembly Main lock 310 Assembling Manifold locks for Concentrated ranching Same Flow Rate with

More information

3 Port Solenoid Valve

3 Port Solenoid Valve Port Solenoid Valve Series VQ00 Courtesy of Steven Engineering, Inc.-0 Ryan Way, South San Francisco, C 9080-0-Main Office: (0) 88-900-Outside Local rea: (800) 8-900-www.stevenengineering.com Outstandingly

More information

Low Differential Pressure Sensor ±1% F.S.

Low Differential Pressure Sensor ±1% F.S. CAT.ES100-49 A Low Differential Pressure Sensor Rated differential pressure range: 0 to 2 kpa Accuracy: ±1% F.S. LED display to confirm energization Series PSE550 Proof pressure: 65kPa Output: 1 to 5VDC

More information

Head-separated Digital Pressure Sensor DP5 SERIES DPH SERIES

Head-separated Digital Pressure Sensor DP5 SERIES DPH SERIES 76 ORDER GUIDE DP / configuration diagram Intermediate cable s Type Vacuum pressure Positive pressure Compound pressure Appearance An intermediate cable is required to connect the controller and the sensor

More information

2-Color Display Digital Pressure Switch. NPN/PNP open collector 2 outputs added. Cut-to-zero display function added. Rated Pressure Metal Body Type

2-Color Display Digital Pressure Switch. NPN/PNP open collector 2 outputs added. Cut-to-zero display function added. Rated Pressure Metal Body Type Series ISE70/75/75H New NPN/PNP open collector 2 outputs added. Cut-to-zero display function added. For General Fluids For Air 2-Color Display (Green/Red) Selectable from four patterns ON Red Green Red

More information

2-Colour Display Type High-Precision Digital Pressure Switch Series ZSE30/ISE30 How to Order Option 1 Without lead wire Nil Lead wire with connector (Lead wire length: 2m) L For positive pressure For vacuum/low

More information

Transmitters: Relay Valve

Transmitters: Relay Valve Relay Valve VR5/5 Series Appropriate output sequences are affected according to the signal received from the mechanical valve. It is equivalent to the auxiliary relay of an electrical system. Specifications

More information

Air Catch Sensor. Non-Contact Sensor for Workpiece Placement Confirmation

Air Catch Sensor. Non-Contact Sensor for Workpiece Placement Confirmation Air Catch Sensor Non-Contact Sensor for Workpiece Placement Confirmation Stable detection of. to. mm clearance Due to the pneumatic bridge circuit and semiconductor pressure sensor, the non-contact type

More information

Tube Fitting Stainless SUS316 Compression Fitting Series

Tube Fitting Stainless SUS316 Compression Fitting Series http://www.pisco.co.jp FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Compression Fitting of Corrosion Resistant Steel Tube Fitting SUS316 Compression Fitting 120 Chemical Industry Medical Industry

More information

1 Pneumatics. Transmitters VR4151 VR4152 VR1210 VR1220 VR1210F VR1220F VR1211F VR VR3200 VR3201 VR3100 VR3110

1 Pneumatics. Transmitters VR4151 VR4152 VR1210 VR1220 VR1210F VR1220F VR1211F VR VR3200 VR3201 VR3100 VR3110 Best 1 Pneumatics Transmitters Relay valve P. 1900 Side piping: 30 x 53 x 91 Bottom piping: 30 x 8 x 91 VR151 VR152 Effective area (mm 2 ) Number of ports Function 7 5 Metal Spool Shuttle valve P. 1902

More information

MICRO EJECTORS ME12, ME25, ME60. Specifications. Mass MICRO EJECTORS. Vacuum switches. Micro ejectors. Single and twin solenoid valves.

MICRO EJECTORS ME12, ME25, ME60. Specifications. Mass MICRO EJECTORS. Vacuum switches. Micro ejectors. Single and twin solenoid valves. ME12, ME25, ME60 Specifications Micro ejectors Media Operating pressure range MPa [psi.] Operating temperature range C [ F] Nozzle diameter Note mm [in.] kpa [in.hg] flow rate Note R/min [ft. 3 /min.]

More information

2-Color Display Digital Pressure Switch. Rated Pressure Metal Body Type (ISE75H) 2-color digital. Functions

2-Color Display Digital Pressure Switch. Rated Pressure Metal Body Type (ISE75H) 2-color digital. Functions Series ISE70/75/75H NPN/PNP open collector 2 outputs added. Cut-to-zero display function added. For General Fluids For Air 2-Color Display (Green/Red) Selectable from four patterns ON Red Green Red Green

More information

Circuit of directional control valve and regulator. Simplifying circuit design. Space saving and piping. work eliminated. Automating pressure control

Circuit of directional control valve and regulator. Simplifying circuit design. Space saving and piping. work eliminated. Automating pressure control Port Electro-Pneumatic Proportional Valve Series 000/000 Capable of actuating a cylinder and performing analog control of pressurization alone can be used to switch and actuate a cylinder and to perform

More information

Body width of 10mm, Nl/min (49.08) 2W (Standard) Nl/min (78.52) 4W (U type: Large flow) Vacuum applications possible (up to 100kPa) 3 S.

Body width of 10mm, Nl/min (49.08) 2W (Standard) Nl/min (78.52) 4W (U type: Large flow) Vacuum applications possible (up to 100kPa) 3 S. High speed coil with stable response times ON: 4ms, OFF: 2ms, Dispersion accuracy: ±1ms (With light and surge voltage suppressor at a supply pressure of 0.5MPa, subject to clean, dry air) 4 Port Direct

More information

10 VQ F. Nil Latching type: Push-locking type (Tool required) B. Nil. Electrical entry

10 VQ F. Nil Latching type: Push-locking type (Tool required) B. Nil. Electrical entry Series 0-VQ00 port solenoid valve How to Order Valves 0 VQ 0 F ir cylinder Clean series Series VQ Compact port valve Type of actuation Normally closed Note) Normally open Note) Normally open type is available

More information

Minimal Fitting Series

Minimal Fitting Series http://www.pisco.co.jp FITTING CONTROLLER VALVE TUE MAKE-TO-ORDER PRODUCTS Ultra-Small arb Fitting for Pneumatic Piping Fitting 266 Suitable for Vacuum Piping by a Combination with Vacuum Tube Suitable

More information

Tube Fitting Anti-spatter Series

Tube Fitting Anti-spatter Series FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Flame-Retardant Spatter-proof Push-In Fitting Type for Pneumatic Piping Anti-spatter 204 Flame-Retardant Resin. Resistant to Flame and Weld Spatter.

More information

Sub-D Connector. Concentrated wiringd Connector for Manifold type. Lead-Out Direction of cable is selectable. Suitable for PISCO's Solenoid Valves.

Sub-D Connector. Concentrated wiringd Connector for Manifold type. Lead-Out Direction of cable is selectable. Suitable for PISCO's Solenoid Valves. http://www.pisco.co.jp SOLENOID IR VLVE PREPRTION CTUTOR PLRILCHIN HRMO ROOT PRTS Concentrated wiringd Connector for Manifold type Sub-D Connector 162 Lead-Out Direction of cable is selectable. Suitable

More information

10 switches simultaneously. The settings of the master sensor (source of copy) can be copied to the slave sensors. Reducing setting labor

10 switches simultaneously. The settings of the master sensor (source of copy) can be copied to the slave sensors. Reducing setting labor 2-Color Display High-Precision Digital Pressure Switch ZSE ISE RoHS ZSE ISE IP65 ZSE40 ISE40 M8 connector type ZSE10 ISE10 ISE70 ZSE80 ISE80 PS ISA3 ISA2 ISE35 Applicable Air, Non-corrosive gas, Non-flammable

More information

2-Color Display High-Precision Digital Pressure Switch

2-Color Display High-Precision Digital Pressure Switch 2-Color Display High-Precision Digital Pressure Switch Settings can be copied to up to 1 slave sensors at once. The settings of the master sensor can be copied to the slave sensors. Reduced setting efforts

More information

10 PSE53 0 M5. Port size. M5 x 0.8 ø6 reducer 1/4-inch reducer. the cable at the time of shipment. 10-PSE to -101 kpa

10 PSE53 0 M5. Port size. M5 x 0.8 ø6 reducer 1/4-inch reducer. the cable at the time of shipment. 10-PSE to -101 kpa Series 0-PSE50 Remote type pressure sensor How to Order Clean series 0 PSE5 0 M5 Pressure sensing range Option 0 2 High pressure [0 to MPa] Vacuum [0 to 0 kpa] Low pressure [0 to 0 kpa] Compound pressure

More information

Soft Start-up Valve. AV2000/3000/4000/5000 Series

Soft Start-up Valve. AV2000/3000/4000/5000 Series Soft Start-up Valve V000/000/000/000 Series [Option] C- R- W- C R - W - Start-up valve for low speed air supply to gradually raise initial pressure in an air system and for quick exhaust by cutting off

More information

Push-In Fitting Type Speed Control Valve Speed Controller Series

Push-In Fitting Type Speed Control Valve Speed Controller Series http://www.pisco.co.jp CONTROLLER Air preparation VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Speed Control Valve Rotatable Resin Body and Fitting(JSS Type) Technical information 46 Rotatable

More information

Ejector Valve Unit Series ZYY/ZYX

Ejector Valve Unit Series ZYY/ZYX Ejector Valve Unit Series ZYY/ZYX Series ZYY3 (Solenoid valve: SY3) Nozzle diameter: ø.7, ø1. Type S: Standard type L: Large flow type Ejectors and solenoid valves can be mounted on the same manifold.

More information

3 Port Solenoid Valve Pilot Operated Poppet Type. External pilot

3 Port Solenoid Valve Pilot Operated Poppet Type. External pilot 3 Port Solenoid Valve Pilot Operated Poppet Type Series VG342 Rubber Seal [Option] Low power consumption 4.8 W DC (Standard type) 2 W DC (Energy-saving type) No lubrication required Possible to use in

More information

Speed Controller with One-touch Fitting

Speed Controller with One-touch Fitting Speed Controller with One-touch Fitting Series Elbow Type Reduces labor time! Elbow Brass Stainless steel Electroless nickel plated Stainless steel 33 RoHS TMH y Easo t e us Push-lock type Larger handle

More information

Compact direct acting precision regulator

Compact direct acting precision regulator direct acting precision Components preparation and pressure adjustment / unit CONTENTS Product introduction 6 Safety precautions 62 Discrete (RJB500) 624 Block manifold (MNRJB500) 626 Block configurations

More information

ROD SLIDERS INDEX ACTUATORS GENERAL CATALOG. Characteristics 779. Handling Instructions, and Precautions 783

ROD SLIDERS INDEX ACTUATORS GENERAL CATALOG. Characteristics 779. Handling Instructions, and Precautions 783 Presenting our CAD drawing data catalog ACTUATORS GENERAL CATALOG ROD SLIDERS INDEX Characteristics 779 Handling Instructions, and Precautions 783 Standard Cylinders Specifications 785 Order 78 Dimensions

More information

Power Valve: Regulator Valve. Specifications. Model VEX Operation type Fluid Max. operating pressure Set pressure Air operated.

Power Valve: Regulator Valve. Specifications. Model VEX Operation type Fluid Max. operating pressure Set pressure Air operated. Power Valve: Regulator Valve Series Large capacity relief regulator Rapid tank internal pressure setting, air blow, constant pressure supply and driving, balance and driving, steps directional control

More information

Push-In Fitting Type Speed Control Valve Speed Controller Series

Push-In Fitting Type Speed Control Valve Speed Controller Series http://www.pisco.co.jp CONTROLLER Air preparation VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Speed Control Valve Rotatable Resin Body and Fitting(JSS Type) Technical information 46 Rotatable

More information

Light Coupling Series

Light Coupling Series http://www.pisco.co.jp FITTING ONTROLLER VALVE TUE MAKE-TO-ORDER PRODUTS Push-In Fitting oupling Light oupling 342 oupling with Push-In Fitting. Easy oupling and Uncoupling with One-Hand Operation. Suitable

More information

13 msec (at 500 mm )/18.5 msec (at 1000 mm )

13 msec (at 500 mm )/18.5 msec (at 1000 mm ) Vacuum / Release Unit Series VQD1000-V Rubber Seal Response speed 13 msec (at 500 mm )/18.5 msec (at 1000 mm ) Distance from the unit to the work area [Option] Smooth detachment of a work piece without

More information

Simple Pressure Level Setting. The threshold level is able to adjust simply. Just set the pointer suitable for the displayed pressure level.

Simple Pressure Level Setting. The threshold level is able to adjust simply. Just set the pointer suitable for the displayed pressure level. SERIES LED Bar Display Mechanical Switch is Out of Date Choose the Contemporary Pressure Sensor with LED Bar Display Marked Conforming to EMC directive Bright LED Bar Display Easy to read the pressure

More information

3-step setting. 2-Color Display High-Precision Digital Pressure Switch. Series ZSE30A(F)/ISE30A. Added vacuum range.

3-step setting. 2-Color Display High-Precision Digital Pressure Switch. Series ZSE30A(F)/ISE30A. Added vacuum range. 2-Color Display High-Precision Digital Pressure Switch Series ZSE3A(F)/ISE3A RoHS Can copy to up to 1 switches simultaneously. The settings of the master sensor can be copied to the slave sensors. Reducing

More information

ITVX Series. Stepless control of air pressure proportional to an electrical signal. Supply pressure: 5.0 MPa

ITVX Series. Stepless control of air pressure proportional to an electrical signal. Supply pressure: 5.0 MPa 5.0 MPa Maximum Supply Pressure High Pressure Electro-Pneumatic Regulator X Series This product is only for blowing gas. This product does not have sufficient pressure control for other applications (driving,

More information

Clean Air Module. Digital flow switch Regulator ON/OFF valve Restrictor Filter

Clean Air Module. Digital flow switch Regulator ON/OFF valve Restrictor Filter Clean Air Module Series Digital flow switch Regulator ON/OFF valve Restrictor Filter Modularizes clean equipment (Reduced piping man-hours/space-saving). Easily obtains clean air. Built-in one-touch fitting

More information

KV series. Innovatively detachable Manifold Block. Smart Solenoid Valve (plug-in type, D-SUB multi-connector type)

KV series. Innovatively detachable Manifold Block. Smart Solenoid Valve (plug-in type, D-SUB multi-connector type) CAT.1101E-S www.sym1.com KV series Innovatively detachable Manifold Block (DIN Rail Mounting) Smart Solenoid Valve (Plug-in type, D-SUB multi-connector ) Compact size with large flow capacity Exceedingly

More information

Electronic pressure switch for air

Electronic pressure switch for air pressure switch Sensors / pressure sensor Overview pressure is electrically detected, displayed and outputted. Features Various sort Wide variation is acailable from small sensor to display. CONTENTS Series

More information

Vacuum Ejector with Solid State Timer

Vacuum Ejector with Solid State Timer Vacuum Ejector with Solid State Timer Incorporates solid state timer function for release valve control (Timer setting with PLC is unnecessary) Timing Chart OFF Suction command ON Suction output OFF ON

More information

Vacuum applications possible (up to 100kPa) Base mounted. Cylinder bore size (mm) Series CM2. Pressure: 0.5MPa Load ratio: 50% Cylinder stroke: 300mm

Vacuum applications possible (up to 100kPa) Base mounted. Cylinder bore size (mm) Series CM2. Pressure: 0.5MPa Load ratio: 50% Cylinder stroke: 300mm 4 Port Direct Operated Poppet Solenoid Valve Series D1000 High speed coil with stable response times ON: 4ms, OFF: 2ms, Dispersion accuracy: ±1ms (With light and surge voltage suppressor at a supply pressure

More information

Vacuum / Release Unit

Vacuum / Release Unit Rubber Seal Vacuum / Release Unit Series VQD1000-V Response speed 13 msec (at 500 mm )/18.5 msec (at 1000 mm ) Distance from the unit to the work area Smooth detachment of a work piece without over-blow

More information

BKUA002 Ver.1.0. Vacuum MICRO EJECTOR. INSTRUCTION MANUAL Ver.1.0

BKUA002 Ver.1.0. Vacuum MICRO EJECTOR. INSTRUCTION MANUAL Ver.1.0 BKUA002 Ver.1.0 MICRO EJECTOR INSTRUCTION MANUAL Ver.1.0 Handling Instructions and Precautions Solenoid Plug connector Manual override Internal circuit DC5V, DC6V, DC12V, DC24V (GA010LE1, GAV010LE1-11)

More information

Series AV2000/3000/4000/5000

Series AV2000/3000/4000/5000 Soft Start-up Valve Series AV/3/4/5 Series introduced! A start-up valve that gradually increases supply pressure during start up and rapidly exhausts system air when the supply air is shut off AC AV AU

More information

Pneumatic components (Electro pneumatic Regulator) Safety Precautions. 3 When releasing secondary control pressure,

Pneumatic components (Electro pneumatic Regulator) Safety Precautions. 3 When releasing secondary control pressure, Pneumatic components (Electro pneumatic Regulator) Safety Precautions Read this before starting use. Please refer to Intro 43 for general details on the pneumatic components, and to " Precautions" in this

More information

High-frequency AC Method. panasonic-electric-works.net/sunx

High-frequency AC Method. panasonic-electric-works.net/sunx 1091 PHOTO PHOTO Thin Type Ionizer High-frequency AC Method General terms and conditions... F-17 Related Information Glossary of terms... P.1401 guide... P.1075~ General precautions... P.1405 Conforming

More information

* E8MS-N1 is only 1-channel pressure sensor controller. E80-C2 can be used. For more details, please refer to E80 catalogue.

* E8MS-N1 is only 1-channel pressure sensor controller. E80-C2 can be used. For more details, please refer to E80 catalogue. Authorised Distributors:- ASH & ALAIN INDIA PVT LTD S-, F.I.E.E., Okhla Industrial Area, Phase-ii, New Delhi-(India) Tel : -7977 Fax : -7977 E-mail : sales@ashalain.com Sensor Four-Input-Channel Sensor

More information

Related Products VR4151/4152 Relay Valve

Related Products VR4151/4152 Relay Valve Related Products VR4151/4152 Relay Valve Appropriate output sequences are affected according to the signal received from the machanical valve. Specifications 1 Fluid Air Operating pressure 0 to 1.0MPa

More information

MICRO EJECTORS CONTENTS

MICRO EJECTORS CONTENTS CAD drawing data catalog is available. ACCESSORIES GENERAL CATALOG AIR TREATMENT, AUXILIARY, VACUUM, AND FLUORORESIN PRODUCTS CONTENTS GME05, GME07, GME10 Series Featrues 679 Specifications 680 Order Codes

More information

(Actual size) 2 switches 10 switches. Push Adjust to the set-value by the or button.

(Actual size) 2 switches 10 switches. Push Adjust to the set-value by the or button. Digital Pressure Switch RoHS compliant Low profile 9.8 mm (Actual size) 13.5 mm 53.4 mm Vertical mounting space reduced to approx.! 1 2 Reduced in depth! 26.1 mm Can copy to up to 1 switches simultaneously.

More information

Air Catch Sensor. Series ISA. For Workpiece Placement Confirmation

Air Catch Sensor. Series ISA. For Workpiece Placement Confirmation Air Catch Sensor Series ISA For Workpiece Placement Confirmation No-contact sensor for confirming workpiece placement, with a configuration that is less affected by supply pressure change. ZSE ISE ZSP

More information

! Contact our sales office regarding a delivery date or a price since this is a special model. Auto switch D-M9 series mountable

! Contact our sales office regarding a delivery date or a price since this is a special model. Auto switch D-M9 series mountable ! Contact our sales office regarding a delivery date or a price since this is a special model. P.G.Information (Specialized Product) Electric Stopper Cylinder/LEBH-X3 Series SP147X-019E-1 RP:SX SMC Corporation

More information

Vacuum Ejector. Adaptable for manifold application

Vacuum Ejector. Adaptable for manifold application Vacuum Ejector Series ZM ZX All in One! Built-in suction filter and silencer Air supply valve for generating a vacuum Vacuum release valve (equipped with a flow volume adjustment valve) Vacuum pressure

More information

ZFC Series. Air Suction Filter. In-line Type with One-touch Fittings

ZFC Series. Air Suction Filter. In-line Type with One-touch Fittings Air Suction Filter ZFC Series N402 IN/OUT straight piping Lightweight molded resin parts Cartridge type element replacement One-touch fittings for easy installation and removal Series ZFC An in-line type

More information

HL (AZH) Limit Switches

HL (AZH) Limit Switches COMPACT SIZE LIMIT SWITCHES HL (AZH) Limit Switches Wide selections of actuators, terminals and bodies to meet any application Excellent environmental resistance Die casting caseiec IP67 Plastic caseiec

More information

OM Field-Type I/P Converter Model : KUX113 User's Manual

OM Field-Type I/P Converter Model : KUX113 User's Manual OM2-5900-1130 Field-Type I/P Converter Model : KUX113 User's Manual Copyright, Notices and Trademarks 1994-2012 Azbil Corporation All Rights Reserved. While this information is presented in good faith

More information

ASP330F-01 ASP430F-02 ASP530F-03 ASP630F-04 ASP430F-F02 ASP530F-F03 ASP630F-F04 R 1/4 R 3/8 R 1/2 R 1/4 R 3/8 R 1/2 NPT 1/8 NPT 1/8 NPT 1/4

ASP330F-01 ASP430F-02 ASP530F-03 ASP630F-04 ASP430F-F02 ASP530F-F03 ASP630F-F04 R 1/4 R 3/8 R 1/2 R 1/4 R 3/8 R 1/2 NPT 1/8 NPT 1/8 NPT 1/4 Pilot check valve and speed controller are combined. Realizes momentary intermediate stoppage of a cylinder and able to adjust speed control of it. Work piece Example of drop prevention circuit Tubing

More information

Vacuum Equipment. Application. Series

Vacuum Equipment. Application. Series Equipment Series Application Page ejector In-line vacuum ejector Multistage ejector ejector with check valve Pad with check valve ejector for water soluble coolant removal ZH ZU ZL1/2 (Special order product)

More information

EX Series. Electric Actuators for Ball and Butterfly Valves

EX Series. Electric Actuators for Ball and Butterfly Valves EX Series Electric Actuators for Ball and Butterfly Valves Next Generation Electrical Actuator Realization of Upgraded General-Purpose Actuators The modularization and the adoption of common parts have

More information

Manual override. Non-locking push type (Tool required) Nil: B: Locking type (Tool required) C: Locking type (Manual) Electrical entry

Manual override. Non-locking push type (Tool required) Nil: B: Locking type (Tool required) C: Locking type (Manual) Electrical entry Plug-in nit Series 0 1 2 3 4 Series Type of actuation Metal Rubber 2 position single 3 position closed 3 position pressure Manifold Option How to Order Valves VQ 1 1 1 0 Y 5 LO Body type 1 0 1 Seal Metal

More information

Micro-differential Pressure High-precision Digital Pressure Sensor For Gas DP-M SERIES

Micro-differential Pressure High-precision Digital Pressure Sensor For Gas DP-M SERIES MODE 729 Micro-differential Pressure High-precision Digital Pressure Sensor For Gas SERIES Related Information General terms and conditions... F-3 Glossary of terms... P.1563~ guide... P.699~ General precautions...

More information