Bremmen Automatic Headlight Conversion Kit Installation Instructions

Transcription

1 Bremmen Automatic Headlight Conversion Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety.

2 INTRODUCTION Bremmen Automatic Headlight Conversion Kit The Bremmen Automatic Headlight Conversion Kit features the following: Converts your VW to the same automatic headlight operation that is normally an option only available on top of the line models. Comes complete with a new headlight switch and light sensor. Simple installation BASIC SKILLS REQUIRED SOME EXPERIENCE RECOMMENDED ADVANCED SKILLS & EXPERIENCE REQUIRED PROFESSIONAL SKILLS & SPECIALTY TOOLS REQUIRED Installing the Bremmen Automatic Headlight Conversion Kit is an enjoyable project that can be completed in a short couple of hours. Electrical work can be intimidating at times, but these easy to follow instructions will make this installation a breeze. Before you begin, read and familiarize yourself with these instructions and make sure you have all the required tools on hand. Thank you for purchasing the Bremmen Automatic Headlight Conversion Kit. We appreciate your business! ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

3 TABLE OF CONTENTS Required Tools and Equipment...pg.3 Kit Contents...pg.4 Shop Supplies and Materials...pg.4 Installation Notes...pg.5 Preparation and Safety...pg.5 Installing the Headlight Conversion Kit...pg.6 Automatic Headlight Configuration...pg.22 REQUIRED TOOLS Non Marring Trim Tool ES# T20 Torx Driver ES#11417 Straight and Angled Pick Side Cutters ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

4 BREMMEN AUTOMATIC HEADLIGHT CONVERSION KIT CONTENTS Headlight Switch Precut Wire with Terminal Ends Light Sensor Module SHOP SUPPLIES AND MATERIALS Hand Cleaner/Degreaser... Available at ecstuning.com...es# Plastic Wire Ties... Available at ecstuning.com...es#5839 ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

5 INSTALLATION NOTES RH refers to the passenger side of the vehicle. LH refers to the driver side of the vehicle. Always use the proper torque specifications. If applicable to this installation, torque specifications will be listed throughout the document and at the end as well. Please read all of these instructions and familiarize yourself with the complete process before you begin. GENERAL PREPARATION AND SAFETY INFORMATION ECS Tuning cares about your health and safety. Please read the following safety information. This information pertains to automotive service in general, and while it may not pertain to every job you do, please remember and share these important safety tips. Park your car in a safe, well lit, level area. Shut the engine off and remove the key from the ignition switch. Make sure any remote start devices are properly disabled. Always wear safety glasses. Make sure the parking brake is applied until the vehicle is safely lifted and supported. If using an automotive lift, be sure and utilize the factory specified lift points. Lifting a vehicle in an incorrect location can cause damage to the suspension/running gear. When lifting a vehicle using a jack, always utilize the factory specified lift points. Lifting a vehicle in an incorrect location can cause damage to the suspension/running gear. Always support the vehicle with jack stands. Always read and follow all safety information and warnings for the equipment you are using.! Never get underneath a vehicle that is supported only by a jack. Always make sure that the vehicle is securely supported on jack stands. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

6 Step 1: Make sure the headlight switch is in the off position. Step 2: 3. Desired position Push in on the center of the switch knob, turn it slightly to the right, and release it. The switch knob will stay in this position as shown in the picture. 2. Turn 1. Push in here ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

7 Step 3: Pull the headlight switch out of the dash. Step 4: Depress the locking tab with your thumb (arrow/highlighted), and pull the connector out of the back of the headlight switch. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

8 Step 5: Locate the empty headlight switch connector pin location number three. It is located between pin two (purple wire) and pin four (black wire with a purple tracer) NOTE The headlight switch connector is a ten pin connector. Each of the pin locations is assigned a number one through ten. Look closely at the back of the connector and you will see a reference number at each corner that will allow you to identify the specific pins in between. Wire color may vary depending on vehicle options and year, but the pin location will be the same. 5 Pin 3 location 1 Step 6: Using a pick, carefully release the terminal retaining tab on same side as the empty cavity. The inset shows a side view of the connector. Retaining tab engaged Retaining tab released ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

9 Step 7: Insert one of the terminals into the connector (both terminals and wire ends are the same). The terminal has an indexing tab that will only allow it to fit into the connector one way. Step 8: Push the terminal all the way into the connector until you hear it click in place. You will also be able to see that it is lined up and positioned the same as the other terminals. New terminal ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

10 Step 9: Fold the terminal retaining tab back down and using your thumb and forfinger, squeeze the connector until you hear the retaining tab click securely into place. Step 10: Using a non-marring trim tool, remove the fuse panel cover on the LH side of the dash. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

11 Step 11: Use the picture on the right as a frame of reference for the installation location of the light sensor, then proceed to step 12. The LH side of the dash near the base of the A pillar is an ideal location. Light Sensor Step 12: Clean the mounting location on the dash thoroughly to remove any grease or oil. Remove the backing from the adhesive tape on the sensor and press it into place. NOTE Sensor operation is not affected by the partial tinting at the base of the windshield. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

12 Step 13: Beginning near the sensor, gently press the wire for the sensor down in between the LH side of the dash and the A pillar trim. Step 14: Continue around the A pillar until the wire is completely hidden and exits into the opening in the LH side of the dash. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

13 Step 15: Insert the light sensor module into the left side of the dash and pull it out the opening for the headlight switch. Step 16: Plug the headlight connector with the new terminal installed into the light sensor module. You should hear a click when the connector is fully seated. You will also hear a series of beeps from the car to signify that it has recognized the new sensor. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

14 Step 17: Secure the new wire to the original harness using a wire tire as shown, then trim the excess from the wire tie. Step 18: If equipped, remove the storage bin from the LH side of the dash by opening it fully, pressing in on both sides to release the catches, then pulling it the rest of the way out. This makes it easier to run the new wire, but if your vehicle does not have this, the wire can still be accessed from under the dash. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

15 Step 19: Route the new wire through the opening for headlight switch, down through the dash and into the driver s footwell. Step 20: Bundle the extra wire for the light sensor and secure it together with a wire tie, trim the excess from the wire tie, then re-install the storage bin and the fuse panel cover on the end of the dash. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

16 Step 21: Connect the light sensor module to the new headlight switch. You will hear a click when the module is fully seated in the switch. Step 22: Push the new headlight switch into the dash until you hear a click indicating that it is fully seated. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

17 Step 23: Using a T20 Torx bit, remove the OBD connector screw. NOTE If your car is not equipped with knee air bags, you do not need to remove the OBD connector. Step 24: Holding the OBD connector out of the way, look up under the dash and you will see three connectors on the bottom of the fuse panel/electrical junction box: black, white, and tan. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

18 Step 25: Disconnect the black connector by pushing in on the release tab and pulling down on the white engagement lever. As you pull down on the white lever, the connector will push out of the electrical junction box. 1. Push release tab 2. Pull down on engagement lever Step 26: Using a pick, release the small locking tabs on the connector housing and slide the housing off the connector body. Reference step 27 for additonal connector detail. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

19 Step 27: The picture on the left shows the housing as it slides off the connector body. The picture on the right shows the inside of the housing and the locking tabs that must be released. Locking Tabs Step 28: Slide the two halves of the connector body apart as shown in the picture. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

20 Step 29: On the lower connector half, locate empty pin location 19 (sixth from the right) between pin 18 (black/green wire) and pin 20 (purple wire). NOTE The pin locations are numbered clearly as shown in the picture. Wire colors may vary depending on options and model year, but the pin location will remain the same. Step 30: Push the new wire into cavity 19 until you hear a click indicating that it is fully seated. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

21 Step 31: Secure the new wire with a wire tie as shown, then trim the excess from the wire tie. Step 32: Slide the connector halves back together. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

22 Step 33: Slide the connector housing back on, then complete the final installation with these steps: Reconnect the black connector Re-install the OBD connector Automatic Headlight Configuration Perform the following steps to configure the automatic headlight operation: Make sure the headlight switch is in the OFF position. Turn the key to the ON Position. Cover the light sensor with your hand. Turn the light switch to the AUTO Position. Turn the light switch to the Headlight Position. Turn the light switch back to the AUTO Position. Three beeps will indicate the configuration is complete. ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH

23 Your Bremmen Automatic Headlight Conversion is complete! Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety. These instructions are provided as a courtesy by ECS Tuning. Although this material has been prepared with the intent to provide reliable information, no warranty (express or implied) is made as to its accuracy or completeness. Neither is any liability assumed for loss or damage resulting from reliance on this material. SPECIFICALLY, NO WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY IS MADE OR TO BE IMPLIED WITH RESPECT TO THIS MATERIAL. In no event will ECS Tuning, Incorporated or its affiliates be liable for any damages, direct or indirect, consequential or compensatory, arising out of the use of this material.