Automatisch vetsmeersysteem Central grease lubrication system Automatisch Fettschmieranlage

Size: px
Start display at page:

Download "Automatisch vetsmeersysteem Central grease lubrication system Automatisch Fettschmieranlage"

Transcription

1 Automatisch vetsmeersysteem Central grease lubrication system Automatisch Fettschmieranlage General instructions for the central grease lubrication system in transportation and industry, equipped with EPG-10 timer, EPG-15 timer and EBCP brake counter. Edition 3/07 Dec. 12

2 NOTES All rights reserved. Nothing from this edition may be reproduced and/or published by means of print, photocopy, microfilm or any other means, without prior written permission from Sterk Technisch Adviesbureau B.V. This also applies to the enclosed drawings and diagrams. Sterk Technisch Adviesbureau B.V. reserves the right to modify parts at any moment, without giving prior or direct notice to the client. The content of this manual may also be changed without advance warning. This manual is valid for the standard model of the product. Therefore, Sterk Technisch Adviesbureau B.V. cannot be held responsible for possible damage resulting from different specifications of the delivered product. For information on adjustments, maintenance tasks or repairs not described in this manual, we ask you to contact the Technical Service Department of Sterk Technisch Adviesbureau B.V. Although this manual has been put together with all possible care, Sterk Technisch Adviesbureau B.V. cannot accept responsibility for possible errors in this document or their consequences. 1

3 General instructions for use of the central grease lubrication system for applications in transportation and industry, equipped with EPG-10 timer, EPG-15 and EBCP brake counter. The ECOSTAR central lubrication system has been constructed from materials of high quality, guaranteeing a long service life and disruption-free operation under the most severe conditions. The result: - reduction of maintenance costs. This manual provides a straightforward description of the operating principle, the system overview, installation and trouble shooting. It is important to read this manual first, in order to obtain maximum efficiency from the system. Table of contents: Page: Notes 1 General introduction / Table of contents 2 System overview tractor / truck with electronic pulse generator EPG-10 3 System overview tractor / truck with electronic pulse generator EPG-15 4 System overview trailer / semi-trailer 5 Operating principle of tractor / truck system Operating principle of trailer / semi-trailer system 6 Technical data of components Information on grease pump 7 Operating principle of components: grease pump, meters 8 Operating principle of electronic pulse generator EPG-10 9 Operating principle of electronic pulse generator EPG Operating principle of brake counter EBCP, solenoid valve, pressure switch, pressure reducing valve, manifolds and truck + trailer / semi-trailer, connection diagrams 11 Where are the various Ecostar components mounted? Parts list for grease pump Installation procedure Filling the grease container Activating the systems Routine check Routine check Recommended lubricants 22 Troubleshooting 23 2

4 System overview tractor / truck with EPG-10 pulse generator 1. Accessory tank 7. Ignition switch 2. Pressure reducing valve 8. Fuse min. 3 Amp 3. Electronic pulse generator / Solenoid valve EPG Pressure switch 4. Grease pump 10. (Bronze) manifold with meters 5. Control light on dashboard 11. Grease points 6. Battery 3

5 System overview tractor / truck with EPG-15 pulse generator 1. Accessory tank 7. Ignition switch 2. Pressure reducing valve 8. Fuse min. 3 Amp 3. Solenoid valve 9. Battery 4. Grease pump 10. Pressure switch 5. Electronic pulse generator EPG (Bronze) manifold with meters 6. Control light on dashboard 12. Grease points 4

6 System overview trailer / semi-trailer with EBCP brake counter 1. Air tank 5. Pressure gauge 2. Overflow valve 6. Brake light (brake command) 3. Electronic brake counter EBCP 7. Manifold with meters 4. Grease pump 8. Grease points 5

7 Operating principle of tractor / truck system The air-controlled grease pump is largely made from stainless steel and equipped with a support piston in the grease container. This provides a clear indication of the grease level. Activation of the grease pump is controlled by a combination of electronic pulse generator (timer) and solenoid valve, type EPG-10, which is fitted under the grease pump or is controlled by an electronic pulse generator (timer) type EPG-15, which is mounted in the central fuse box, in combination with a solenoid valve which is fitted under the grease pump. The EPG-10 and EPG-15 measures the time as long as the ignition is on. Once the (previously) set time has been reached, the EPG-10 and EPG-15 sends a signal to the solenoid valve. The solenoid gives an air command to the grease pump, which will press the grease into the main tubing, manifolds and meters (in the right quantity) and through the secondary tubing to the grease points. After ± 3 minutes the signal shuts off, the air is released and the grease pump pressure falls away. A visual check of the correct functioning of the grease lubrication system is possible with the help of the control light (EPG-10 + EPG-15), fitted on the dashboard. This will light up during the ± 3 minute grease cycle and then go out again. If the control light remains lit continuously, this indicates a fault in the system. If the air pressure is higher than ± 12 bar, a pressure reducing valve must be employed. The EPG-15 is equipped with a test mode. In this mode, the grease pump alternates between 1 minute of continuous pressure and 1 minute of release, as long as the ignition is on. The control light comes on during the pressure stage, as verification that there is sufficient system pressure. It remains lit continuously if there is a fault. Position Aux on the EPG-15 is for special applications. It is also possible to override the solenoid valve and grease pump manually (for testing or additional lubrication). Operating principle of trailer / semi-trailer system The air-controlled grease pump is largely made from stainless steel and equipped with a support piston in the grease container. This provides a clear indication of the grease level. Activation of the grease pump is controlled by a combination of electronic brake counter / solenoid valve, type EBCP, which is fitted under the grease pump. A signal is given to the brake counter each time the brakes are used. After a preset number of braking operations, an air command is given to the grease pump, which will press the grease into the main tubing, manifolds and meters (in the right quantity) and through the secondary tubing to the grease points. Each time a brake signal is received, the LED lights up green. When the preset brake count is reached, the LED lights up red and an air command is given to the grease pump. After a number of braking operations (the LED now lights up red each time), the air will be released from the grease pump and the counting will restart. The LED will now light up green again. A visual check of pressure build-up and pressure release is possible with the help of the pressure gauge mounted on the front of the grease pump. If the air pressure is higher than ± 12 bar, a pressure reducing valve must be employed. It is also possible to override the solenoid valve and grease pump manually (for testing or additional lubrication). 6

8 Technical data of components 1. Grease pump with support Air pressure: 6-12 bar Grease pressure : Air pressure = 9 :1 piston: Grease output: max. 40cc Capacity grease container: 4 l / 6,5 l 2. Meters: P max. ± 200 bar Reset pressure 9 bar 3. Pulse generator EPG-10: P max. 12 bar Power supply 12 VDC or 24 VDC 4. Pulse generator EPG-15: Power supply between 10 VDC and 32 VDC 5. Solenoid valve: P max. 12 bar Power supply 24 VDC (optional 12 VDC) 6. Brake counter EBCP: P max. 12 bar Power supply 12 VDC or 24 VDC 7. Pressure switch: P max. 125 bar Switch pressure ± 40 bar 8. Pressure reducing valve: Primary. max. 18 bar Secondary max. 10 bar Grease pump with support piston: This grease pump is equipped with a support piston in the grease container. The support piston provides the following advantages: Self-cleaning of the inner surface of the grease container, which makes level checking easier. This eliminates the problem of dried grease remaining on the inner surface. Ensures optimum filling of the pump chamber, even at low temperatures when the grease would be viscous. Prevents coning in the grease container. Ageing of the grease is considerably reduced due to the separation of the grease from the atmosphere. The pump has an output capacity of 40 cm³ at a pressure ratio of 1:9, making it suitable even for the lubrication of very large applications with more than 100 meters (dependent on output of meters used). Air pressure above the support piston ensures that the pump chamber is fully filled in the suction phase. All existing advantages of an entirely closed system are retained. 7

9 Operating principle of the components 1. Grease pump with support piston (truck) The air pressure in cylinder area 1 forces piston 10 upwards. At the same time the lubricant in chamber 2 is compressed, valve 11 closes the passageway 3 to reservoir area 4 and pressure is built up. Simultaneously, this pressure is applied to press grease into the main tubing 5. After the lubrication cycle, the air pressure falls away in chamber 1 and piston 10 is forced downwards by the spring 6. The pressure also falls away in chamber 2 and main tubing 5. The resulting overpressure in the main tubing enables the excess grease to return to chamber 2 and reservoir 4. Valve 11 opens passageway 3 and the lubricant is sucked from the reservoir 4 into chamber 2. After this, the lubrication cycle can start again. While piston 10 is moving upwards, the air above the piston in chamber 7 is partially moved into area 9 (above the support piston) via de-aeration tubing 8; to avoid overpressure above the grease, the air can flow into the free space through insert T- coupling 12 (or insert Y-coupling 16) and de-aeration tubing 15. When piston 10 moves downwards, the compressed air in cylinder area 1 is partially moved into area 9 (above the support piston) via solenoid valve 13 and de-aeration tubing 14 as well as de-aeration tubing 8; to avoid overpressure above the grease, the air can flow into the free space through insert T-coupling 12 (or insert Y-coupling 16) and de-aeration tubing 15. This construction makes it impossible for dirty or moist air from outside to come into direct contact with the grease. 2. Meters Figure A Grease is pumped into area 1 via the main tubing against the spring. The grease in area 2 is then pumped to the lubrication points. Figure B When the grease pressure falls away, the grease in area 1 will disperse to area 2 by means of the spring. 8

10 3. Electronic pulse generator EPG-10 The electronic pulse generator emits a direct pulse to the solenoid valve, assembled on the pump, after a preset interval time of between 10 and a maximum of 480 minutes (ignition on!). The preset pulse duration is adjustable between 1 and a maximum of 10 minutes. Enables visual monitoring of the system s functioning by means of the control light on the dashboard. The manual override can be used to check that the system is working properly. Functional description of single pulse generator, type EPG-10: The pulses emitted by the electronic pulse generator control the solenoid valve, which in turn activates the grease pump. These pulses are stored internally and can be read out afterwards with the help of a portable programmer box. With the programmer box, the time interval can be set between 10 and a maximum of 480 minutes. The pulse duration is also adjustable between 1 and a maximum of 10 minutes. The pulse generator also stores the unsuccessful grease pulses and is equipped with an internal switch, in case a pressure switch is installed in the lubrication system. Reading out and activating the switch is performed via the programmer box. The pulse generator measures the time as long as the engine ignition is on. This time will be stored when the ignition is switched off. The pulse generator then goes into sleep mode. The control light on the dashboard lights up in the following situations: a. output pulse indication while the solenoid valve is being energized. b. low-pressure alarm indication if the pressure in the lubrication circuit has not risen to a sufficient level during the output pulse. The low-pressure alarm indication is equipped with a hold function. This means that, when an alarm is detected, the LED remains lit (the presence of an alarm does not affect the operation of the pulse generator). If the pressure in the lubrication circuit successfully reaches the required level again during a subsequent output pulse, the LED will go out after this pulse. An internal fuse has not been fitted; use an external fuse (max. 3 Amp). Summary of technical specifications: Supply voltage (pulse generator) : 12 and 24 VDC Current (solenoid) : max. 300 ma Output current (lamp) : LED 20 ma with series resistor Output pulse duration : seconds Interval time range : minutes Output in test mode : 60 seconds on / 60 seconds off Operating temperature range : -10 C C Electrical connections : screw connector, 4-conductor cable 9

11 4. Electronic pulse generator EPG-15 The electronic pulse generator emits a direct pulse to the solenoid valve, assembled on the pump, after a preset interval time of between 30 and a maximum of 270 minutes (ignition on!). Enables visual monitoring of the system s functioning. The test mode or the manual override can be used to check that the system is working properly. Functional description of single pulse generator, type EPG-15: The pulses emitted by the electronic pulse generator control the solenoid valve, which in turn activates the grease pump. With the front switch, the time interval can be set between 0.5 and a maximum of 4.5 hours, in half-hour steps. This switch also has a test mode in which a sequence of output pulses (1 minute on / 1 minute off) is generated continuously for quick testing of the (grease) lubrication system. Position Aux is for special applications. Adjustments can only be checked and modified with a programmer box. The pulse generator measures the time as long as the engine ignition is on. If this time is to be stored when the ignition is switched off, there must be a continuous power supply to the battery + connection. In this event, the pulse generator goes into sleep mode. The front LED and control light on the dashboard lights up in the following situations: a. output pulse indication, while the solenoid valve is being energized. b. low pressure alarm indication, if the pressure in the lubrication circuit has not risen to a sufficient level during the output pulse. The low pressure alarm indication is equipped with a hold function. This means that, when an alarm is detected, the front LED and control light remains lit (the presence of an alarm does not affect the operation of the pulse generator). If the pressure in the lubrication circuit successfully reaches the required level again during a subsequent output pulse, an automatic reset will take place and the LED will go out. The front toggle switch has a double function: a. reset of the low pressure alarm, regardless of the position of the pulse generator. b. manual generating output pulse, this overrides the internal clock. An internal fuse has not been fitted; use external fuse (max. 3 Amp). The solenoid output is protected against inductive loads. The pulse generator is mounted using the 2 parker screws. Summary of technical specifications: Supply voltage range : between 10 and 32 VDC Current (sleep mode) : 7 ma at 24 VDC / 2 ma at 12 VDC Current (solenoid) : max. 300 ma Output current (lamp) : LED 20 ma with series resistor Output pulse duration : 180 seconds Interval time range : minutes Output in test mode : 60 seconds on / 60 seconds off Operating temperature range : -10 C C Dimensions : 110 x 40 x 50mm (w x h x d) Electrical connections : plug-in screw connector, max. 4 mm² 10

12 5. Brake counter EBCP (trailers / semi-trailers) Each time the brakes are used a command is given to the brake counter as a result of the brake light coming on. The LED lights up green each time a brake signal is received. When the preset brake count is reached, the electronic brake counter will give a direct pulse to the solenoid valve (mounted on the pump), which gives an air command to the grease pump. The LED now lights up red. After a number of braking operations (the LED now lights up red each time), the air will be released from the grease pump and the counting will restart. The programmer box and manual override can be used to check that the system is working properly (see page 21). With this programmer box, the number of braking signals can be set between 10 and a maximum of Solenoid valve By energizing solenoid A, plunger B is lifted and connection 1 to 2 is effected. Connection 3 will be closed. After the grease cycle, the energizing shuts off, solenoid A is closing connection 1 and the air pressure relieves via connection 3. The manual override (see page 19) can be used to check that the system is working properly. 7. Pressure switch bipolar (truck) Gives a signal when the system pressure reaches approx bar. Industrial application: 8. Pressure reducing valve To reduce a primary pressure (1) that is too high, i.e. > 12 bar, to a lower secondary pressure (2). 9. Manifolds Made of high-quality, corrosion-resistant bronze and can be supplied with 4, 7, 9, 12 or 14 outlets. Easy to fit thanks to threaded end: nut and locking ring provided. 10. Connection diagrams EPG-10 / EBCP 1. Yellow L. Control light on dashboard 2. Brown D. Pressure switch 3. White E. Brake lights 4. Green 5. Blue 6. Red Truck EPG-10 Trailer / Semi-trailer 11

13 Where are the various ECOSTAR components mounted? 12

14 Continued: examples on trucks 13

15 Continued: examples on trailers and semi-trailers 14

16 PVP model with support piston (4 l) / (6.5 l) 15

17 Parts list for grease pump Item no. Code no. Description Spring overfill valve S Overfill valve (kit) Column + foot valve holder 4 l Column + foot valve holder 6.5 l O-ring Pump house A2 Ring (2x) A2 Bolt (2x) O-ring Gauze filter Filling-filter locking ring (kit) /01 Dust hood aluminium (kit) Dust hood rubber O-ring Pin (2x) Type plate Threated end 6,5 ltr A2 nut (2x) Piston tube (kit) Plunger spring Piston (kit) A2 Toothed washer (4x) Bolt (4x) S Cylinder tube (kit) Bolt 4ltr Dubo ring Top cover Cover ring O-ring Support piston Piston guide (kit) Grease holder 4 l Grease holder 6,5 l Level sticker reservoir Ecostar grease pump sticker Recessed-head screw (4x) Ring (4x) Bottom cover O-ring Overflow port Nut Seal washer aluminium De-aeration coupling T De-aeration tubing 25cm 4 l De-aeration tubing 36cm 6.5 l De-aeration tubing 10/15/25cm De-aeration coupling T Insert Y-coupling Seal washer copper (2x) Banjo housing 5/16 / 8mm Banjo housing 10mm Banjo nipple 5/16 / 8mm Banjo nipple 10mm Collar plug Pressure gauge bar 16

18 Installation procedure Location of the grease pump: Mount the pump on the chassis where it is both easily visible and accessible. Preferably in the middle of the vehicle or behind the cabin. Ensure that the fill coupling can be easily reached. Electronic pulse generator EPG-10 / Solenoid valve (tractor / truck): Screw valve using port 2 into the bottom connection of the pump cylinder tube. Install the air tubing from air pressure tank or accessory tank to port 1 connection of the solenoid valve (see system overview on page 3). Fit the insert T-coupling into the exhaust (port 3) of the solenoid valve, the insert T-coupling onto the back of the pump and connect both with the de-aeration tubing (see page 8, no.12, 14 and 15). Connect current supply wires from electronic pulse generator to control light, cabin fuse box compartment and pressure switch. Insulate unused main cable wiring. Connect according to diagram (see page ). Make use of an accessory fuse (max. 3 Amp). Solenoid valve for EPG-15 (tractor / truck): Screw valve with port 2 into the bottom connection of the pump cylinder tube. Install the air tubing from air pressure tank or accessory tank to port 1 connection of the solenoid valve (see system overview on page 4). Fit the insert T-coupling into the exhaust (port 3) of the solenoid valve, the insert T-coupling onto the back of the pump and connect both with the de-aeration tubing (see page 8, no.12, 14 and 15). Electronic pulse generator EPG-15 (tractor / truck): Preferably, this should be fitted in the cabin fuse box compartment. Connect current supply wires from electronic pulse generator to control light, cabin fuse box compartment, pressure switch and solenoid valve. Connect according to diagram (see page10). Make use of an accessory fuse (max. 3 Amp). Push the front toggle switch into manual with ignition on: the solenoid valve should operate now. Electronic brake counter EBCP / Solenoid valve (trailer / semi-trailer): Screw valve using port 2 into the bottom connection of the pump cylinder tube (see system overview on page 5). If no space is present under the pump: mount the brake counter using a mounting support (option) on the side of the grease pump. Install the air tubing from port 2 into the bottom connection of the pump cylinder tube. Install the air tubing from air pressure tank or accessory tank to port 1 connection of the solenoid valve (see system overview on page 5). Fit the insert coupling into the exhaust (port 3) of the brake counter, the insert Y-coupling onto the back of the pump and connect both with the de-aeration tubing (see page 8, no.14, 15 and 16). Connect current supply wires from electronic brake counter to the trailer / semi-trailer power box. Attention: use a present brake light and ground connection in this box. Connect according to diagram (see page 11). Manifolds with meters: The manifolds should preferably be mounted on the chassis girders or the transfer girders (see pages 12, 13 and 14). Remove all lubrication nipples and fit the correct male stud or elbow coupling. Attention! Before removing the lubrication nipples, check if the grease points are well lubricated. If not, then lubricate these first! Attach meter tubing to existing tubing by means of nylon Tie-raps or clamping brackets; always leave sufficient length for moving parts. 17

19 Cutting open the multiple tubing: Avoid damaging and/or cutting the inner tubes. 1. Approximately measure the 2. Strip back. 3. Carefully cut off the stripped- 4. The freed end desired length of the tubing back part without touching looks like this. and cut open the outside the remaining piece. cover. Main tubings: Attach main tubing (5/16 outside diameter synthetic tubing) from pump to manifolds. Use a tubing cutter to make straight, neat cuts in the tubing and assemble as specified. First, place the sleeve nut over the tubing. Then fit the locking ring, with the conical side towards the end of the tubing. Do not forget to mount an insert in the main tubing! Use 3/16 and 5/16 outside diameter tubing for installation and repairs. Do not use flexible tubes due to expansion under pressure. Only use tubes prescribed by the manufacturer. Caution: keep tubing away from hot parts (exhaust etc.). Filling the grease container: The grease container must only be filled via the fill coupling mounted on the side of the grease pump. Remove the dust cap and clean the couplings before filling. Fill the container until the bottom of the support piston reaches the top of the blue triangular sticker. Major resistance can occur during filling if the filter behind the fill coupling is blocked (with dirt). Do not overfill the container. Replace dust cap after filling. Only use greases in NLGI-class EP-0 or EP-00. For lubricants see page 21. Refilling the Ecostar grease pump: On delivery of Ecostar grease pumps, both the grease container and the plunger chamber are filled with grease. This means that after only a few pump strokes, the pump delivers grease. If, however, the minimum grease level has been ignored and the pump has sucked in air, 18

20 Refilling the Ecostar grease pump (continue): many pump strokes may be required before grease is delivered again. After filling the grease container, you can shorten the interruption in the delivery of grease (after disconnecting the main tubing to the pump!) by blocking off the grease exhaust with your thumb during the air release of the pump. This creates a vacuum inside the pump and pressure will rise above the support piston. Grease will be pressed from the container into the plunger chamber. In this way, grease will be delivered after only a few pump strokes. Testing the electronic pulse generator EPG-10, EPG-15 and EBCP brake counter using the programmer box: To allow optimal testing of all three systems, the programmer box is equipped with an extensive program which recognise automatically if an EPG-10 timer, an EPG-15 timer or an EBCP brake counter is connected. The tester offers the possibility of: - Reading the current time and braking settings. - Changing the settings. - Retrieving the history. -Testing the lubrication system. Activating the EPG-10 system (check voltage first!) Manual control of the electronic pulse generator / solenoid valve: Turn ignition on, start the engine, check air tanks: P min. 6 bar. Activate pump cycle by means of the manual override. Put a screwdriver into the groove of the slotted valve and turn slowly clockwise (test / 1) until you feel resistance. Continue to turn slowly until the grease pump builds up pressure. Verify using a pressure gauge. If you turn the screwdriver anticlockwise (stand-by / 0) the air is released and the grease pump pressure falls away. Wait for a moment before operating the slotted valve again. Continue pumping until lubricant emerges from the manifold without air bubbles, insert plug and move on to the next manifold. Proceed until main tubing and manifolds are filled with grease. Verify using the pressure gauge that the pressure of the grease pump in the system is constant; if not, de-aerate again. If necessary, additional lubrication is possible with the manual override. It needs to be operated for long enough to enable the grease pump to build up sufficient pressure. Allow the grease pump to pump a few more times, and check that grease beads appear at all bearings. The system is now ready for operation! Setting time intervals and pulse duration of electronic pulse generator EPG-10: Settings can only be checked and modified using the EPG-10 / EPG-15 / EBCP programmer box. Time interval range: 10 minutes 8 hours, pulse duration range: 1 10 minutes, depending on vehicle use. The default settings are: time interval 2.5 hours, pulse duration 3 minutes. These cannot be changed by the user. If too much grease is delivered, extend the time interval. In the event of insufficient lubrication, shorten the time interval. 19

21 Activating the EPG-15 system (check voltage first!) Manual control of the solenoid valve: Turn ignition on, start the engine, check air tanks, P min. 6 bar. Put a screwdriver into the groove of the slotted valve and turn slowly clockwise (test / 1) until you feel resistance. Continue to turn slowly until the grease pump builds up pressure. Verify using a pressure gauge. If you turn the screwdriver anticlockwise (stand-by / 0) the air is released and the grease pump pressure falls away. Wait for a moment before operating the slotted valve again. With the aid of the electronic pulse generator EPG-15: Turn ignition on, start the engine, check air tanks, P min. 6 bar. Activate pump cycle by means of the test position (A) on the electronic pulse generator (60 seconds on / 60 seconds off). Continue pumping until lubricant emerges from the manifold without air-bubbles, insert plug and move on to the next manifold. Proceed until main tubing and manifolds are filled with grease. Verify using a pressure gauge that the pressure of the grease pump in the system is constant; if not, de-aerate again. Keep the electronic pulse generator in the test position for some time, and check that grease beads appear at all bearings. After this, set the electronic pulse generator to the desired position. Time interval range: hours, depending on vehicle use. The default setting is 2.5 hours, and can be changed by user. If too much grease is delivered, extend the time interval. In the event of insufficient lubrication, shorten the time interval. If the control light stays on, use the front toggle switch (B) to reset. This switch can be used to reset the pressure alarm and also, if necessary, manual generating the output pulse for additional lubrication. The engine ignition must be on in both cases! By using the toggle switch for additional lubrication (manual), it needs to be held for a longer time to enable the grease pump build up sufficient pressure. By releasing the switch, the air is released and the grease pump pressure falls away. Wait for a moment before operating the toggle switch again. The system is now ready for operation! Position Aux (C) is for special applications. Position Aux cannot be changed by user. Adjustments can only be checked and modified with the EPG-10 / EPG-15 / EBCP programmer box. 20

22 Activating the EBCP system (check voltage first!) System check trailer / semi-trailer with EBCP brake counter: To test the system, the EBCP is equipped with a manual override (for testing and additional lubrication). Test procedure: Check air tanks, P min. 6 bar. Put a screwdriver into the groove of the slotted valve and turn slowly clockwise (test) until the grease pump builds up pressure. Verify using the pressure gauge mounted on the front of the grease pump. By turning the screwdriver anti-clockwise (stand-by) the air is released and the grease pump pressure falls away. Wait for a moment before operating the slotted valve again. Attention: the valve can be stick in position test after turning anticlockwise in position stand-by. In this case, close the valve by using a brake command (brake light coming on!). Setting brake count of electronic brake counter EBCP: Settings can only be checked and modified using the EPG-10 / EPG-15 / EBCP programmer box. The number of braking signals can be set between 10 and 250. The default setting is: 80 braking signals, depending on vehicle use. This cannot be changed by the user. If too much grease is delivered, increase the brake count. In the event of insufficient lubrication, decrease the brake count. The system is now ready for operation! Routine check When possible, combine the routine check with other maintenance checks! The following rules are intended as a guide for mechanics and maintenance personnel: Container. Check for: Damage: if cracked, replace with a new unit. Amount of lubricant (page 18): fill with the correct grease (page 22). Leakage in the complete pump. If the cap of the fill coupling has been dislodged, thoroughly clean the coupling before replacing the cap. Electrical connections. Check: Pressure switch, solenoid valve, electronic pulse generator EPG-10, electronic pulse generator EPG-15 or brake counter EBCP for damage / oxidation. Operation of electronic pulse generator by means of test procedure on page 20 (for tractors / trucks only!). General checks: Air tubing and air tank connections leaking or damaged? Blow-off openings blocked? Main tubing leaking or damaged? Operation of pump / electronic pulse generator on tractors /trucks: turn ignition on and follow the test procedure ; check whether grease is reaching the bearings. Verify using a pressure gauge that the pressure of the grease pump in the system is constant. Also test the pump using the manual override of the solenoid valve. On trailers / semi-trailers: check the functioning of the pump using the manual override of the solenoid valve. 21

23 Verify using the pressure gauge that the pressure of the grease pump in the system is constant. Inspect all lubrication points. If a lubrication point is dry (or too greasy) and the tube is not broken, first disconnect the tubing at the lubrication point (or meter). In case of no grease : remove meter and fit a new one of the correct type. In case of too greasy : remove meter and fit a new one of the correct type. Recommended lubricants Other types of grease are permitted, as long as they comply with the specifications printed on the blue and white sticker on the pump s grease container! Use NLGI EPG-0 or NLGI EPG-00 lithium-based greases. Supplier / Specifications (Bio = Biodegradable) Avia Kendall Tedcastle (T.O.P.) AVIALITH 000 EP-0 / 00 L-406 NLGI-0 G-39 AVIALITH 000 EP-00 Bio L-999 NLGI-0/00 AVIA AYNTOGREASE EP-0 Bio Texaco Maxol Multifak 6833 EP-00 BP H Multifak EP-0 Energrease ZS EP-0 / 00 Starfak EP-00 Bio Mobil Castrol Chassis Grease LBZ 00 Total DK-00 grease Mobilit SHC 007 EP-00 Bio Multis EP-0 CLS-00 grease Multis Pennzoil Elf Pennlith EP 700 Grease EP-00 Valvoline Epexa 0 / 00 Semi-fluid Grease EP-00 Q8 Esso Rembrandt EP-0/EP-00 Beacon EP-0 / 00 Rubens EP-00 Fina Shell Ceran AD-0 Retinax CS 0/CS 00 Ceran EP-0 Alvania EP-0 (industrial) Lical Grease EP-0 Bio Chassis Bio Grease 0 Marson EPL-00 22

24 Troubleshooting Always use a pressure gauge, mounted on the front of the grease pump, to verify the system grease pressure! Fault: Cause: Remedy: 1. LED on dashboard System not reaching pressure. Check grease pump pressure using stays on. pressure gauge. Grease container empty and Fill container and de-aerate the air bubbles in main system. system. Pressure switch giving no signal. Check for wire ruptures or replace pressure switch. Main tubing broken. Repair (see 5). Temporary electrical fault. Check electronic pulse generator and fuse (see 3.). Reset pulse generator. Defective grease pump. Check grease pump (see 2). Defective solenoid valve. Check or replace valve (see 4). No air pressure. Air pressure 6 12 bar. 2. Pump does not work, No air pressure. Air pressure 6 12 bar. fails to reach pressure. Defective solenoid valve. Check or replace valve (see 4). Defective pulse generator. Replace pulse generator (see 3). Grease container empty and air in Fill container and de-aerate the pump pump. and, if necessary, the system. Piston does not go upwards. Disassemble tube and check piston. 3. Electronic pulse genera- Poor or interrupted connection. Check connections. tor does not work. Short-circuit. Check contacts. Defective fuse. Replace fuse, check contacts. Defective pulse generator. Replace pulse generator. 4. Solenoid valve does not Poor or interrupted electrical circuit. Check circuit, test manual override work, or does not work Blocked / dirty. Bad connection. without the electronic pulse generator properly. and check connections. 5. All bearings dry. Grease container empty. Fill container: see filling procedure + de-aerate system (see pages 18-21). Defective fuse or wire rupture. Check contacts / wire; repair or renew as necessary. Defective solenoid valve or Check, clean or replace valve and air tubing fractured. repair tubing. Defective pulse generator. Replace pulse generator (see 3). Main tubing fractured. Repair tubing and de-aerate when new piece of tubing is used. Wrong grease (too thick). Clean the container and pump the old grease out of the system (remove end stops from meter manifolds). Refill with the correct grease (see pages 18, 19 and 22). 6. One or more bearings Rupture in tubing to meter. Repair / fit new tubing. are dry. Lubrication frequency too low. Adjust pulse generator. Defective meter. Replace meter. Wrong output from meter. Replace meter with one of right size. 7. One or more bearings Meter leaking internally. Replace meter. have an excess of grease. Lubrication frequency too high. Adjust pulse generator. Wrong output from meter. Replace meter with one of right size. 23

25 NOTES / DRAWINGS 24

26 TECHNISCH ADVIESBUREAU BV Veersteeg LR Spijk Holland Tel. +31 (0) Fax +31 (0) Internet: info@sterk.com

16000SIII Automatic Grease System

16000SIII Automatic Grease System Manual # 99905495 16000SIII Automatic Grease System Effective 20120716 IOWA MOLD TOOLING CO., INC. PO Box 189 Garner, IA 50438 Tel: 641-923-3711 FAX: 641-923-2424 Website: http://www.imt.com Copyright

More information

HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number , , , , or no number at all)

HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number , , , , or no number at all) HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number 500089, 500105, 500210, 500456, 500535 or no number at all) Visit us on the web at www.lci1.com 82-L0040-01 Rev. 1 WARNING

More information

CONTROLLER DIAGNOSTIC GUIDE

CONTROLLER DIAGNOSTIC GUIDE Proprietary tice: This document contains proprietary information which not to be reproduced, transferred, to other documents, disclosed to others, used for manufacturing or any other purpose without the

More information

HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number , , , , or no number at all)

HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number , , , , or no number at all) HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number 500089, 500105, 500210, 500456, 500535 or no number at all) Visit us on the web at www.powergearus.com 82-L0040-01 Rev.

More information

Electric pump EP-1. Electric pump with 1.9 kg reservoir:

Electric pump EP-1. Electric pump with 1.9 kg reservoir: The BEKA-MA central lubrication pump model EP-1 is electrically actuated and has up to a maximum of independently operating lubricant outlets. A separate pump element is required for each outlet. Three

More information

Farval. Dualine Installation System Start-Up. Bulletin DL300 BIJUR DELIMON INTERNATIONAL

Farval. Dualine Installation System Start-Up. Bulletin DL300 BIJUR DELIMON INTERNATIONAL Farval Dualine Installation System Start-Up Bulletin DL300 BIJUR DELIMON INTERNATIONAL 2685 Airport Road Kinston, NC 28504 Tel. 800-227-1063 Fax: 252-527-9232 website: www.bijurdelimon.com DC1-1 SECTION

More information

MICRO EJECTORS. Micro ejector single unit (without solenoid valve) ME. Micro ejector with solenoid valve DC24V. Block-off plate ME MA-BP

MICRO EJECTORS. Micro ejector single unit (without solenoid valve) ME. Micro ejector with solenoid valve DC24V. Block-off plate ME MA-BP Micro Ejector Order Codes Manifold Order Codes Micro ejector single unit (without solenoid valve) ME Body model nozzle diameter : Maximum flow rate on vacuum side 03 0.3 : 3.0R/min. [0.012in., 0.106ft.

More information

OPTIONS AUTOMATIC LUBRICATION SYSTEM

OPTIONS AUTOMATIC LUBRICATION SYSTEM OPTIONS AUTOMATIC LUBRICATION SYSTEM The central lubrication of the axes modules consists of a small lubricant dispenser with progressive distributor with several exits. It is responsible for the automatic

More information

Statim G4 Error Codes

Statim G4 Error Codes Statim G4 Error Codes All leaks should be corrected before proceeding with troubleshooting Cycle Fault #1 The cassette temperature failed to reach 95 C within a time-out period. 1. An extremely large steam

More information

Installing the Throttle Commander Ford F250 F550 Super Duty

Installing the Throttle Commander Ford F250 F550 Super Duty Installing the Throttle Commander Ford F250 F550 Super Duty 6.0 L Power Stroke Diesel 2003.25 2004 T500082, T500083 and T500084 1.0 Preparing for Installation...5 2.0 Installing the Throttle Control Box...5

More information

Operation and service manual

Operation and service manual Operation and service manual SKF Multilube SKF Multilube Central lubrication system Table of contents General system description... 1 Safety instructions... 1 General information on centralized lubrication

More information

EUGEN WOERNER GmbH & Co. KG Postfach 1661 DE Wertheim Am Eichamt 8 DE Wertheim. Pump unit GMZ-E

EUGEN WOERNER GmbH & Co. KG Postfach 1661 DE Wertheim Am Eichamt 8 DE Wertheim. Pump unit GMZ-E Pump unit GMZ-E Pump used to supply oil and grease from a barrel directly through a lid-hole or a bunghole. Technical data: Pump with bung-hole Pump with barrel lid Delivery volume per stroke: Pump element

More information

PowerLevel s e r i e s

PowerLevel s e r i e s Owner s Manual Hydraulic Leveling CONTENTS Introduction Operation Control Panel Automatic Leveling Manual Leveling Retracting Jacks Remote Operation Care & Maintenance Troubleshooting Error Codes 1 2 2

More information

Heavy duty slurry pumps

Heavy duty slurry pumps USERS MANUAL Heavy duty slurry pumps TOYO PUMPS EUROPE Edition 27.07.2007 SAFETY INSTRUCTIONS TOYO PUMPS EUROPE Users manual for Toyo pumps type «DP..-6 30~40HP» This users manual will help you to maintain

More information

Models CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" - Q3. MAY FORM Section

Models CHASSIS LUBE ELECTRIC GREASE PUMP Series C - Q3. MAY FORM Section Models 94822 CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" - Q3 MAY - 2004 FORM 403468 Section Page - 14B 13.00" (330 mm) 17.72" (450 mm).35" (9 mm) Mounting Holes 4.72" (120 mm) 9.84" (250 mm) Figure 1

More information

HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL

HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number 500675) touchpad 500675 82-L0140-00 REV.3 WARNING DO NOT USE THE POWER GEAR HYDRAULIC LEVELING SYSTEM (OR AIR SUSPENSION)

More information

Owner s and Maintenance Manual for: Lincoln QuickLub Systems

Owner s and Maintenance Manual for: Lincoln QuickLub Systems Owner s and Maintenance Manual for: Lincoln QuickLub Systems Contents: I. Introduction 1. System Operation 2. Components II. Pump Mounting and Wiring 1. Power 2. Testing III. Purging and Testing IV. Programming

More information

Heavy duty slurry pumps

Heavy duty slurry pumps USER S MANUAL Heavy duty slurry pumps TOYO PUMPS EUROPE Edition 27.07.2007 SAFETY INSTRUCTIONS TOYO PUMPS EUROPE User s manual for Toyo pumps type «GR..-2 3~10HP» This user s manual will help you to maintain

More information

Starting up hydraulic systems

Starting up hydraulic systems General / Installation A hydraulic system that operates economically, safely, and trouble-free requires careful planning, as well as proper installation and start-up. Conscientious maintenance has a considerable

More information

FPS- 80. Manual. Reverso Pumps, Inc. Ph: (954)

FPS- 80. Manual. Reverso Pumps, Inc.   Ph: (954) FPS- 80 Manual Table of Contents System Overview... 1 Control Panel Overview... 2 Technical Specifications... 3 Electrical and Installation... Tank Diagrams... 5 Initial Setup... 6 Digital Timer Instructions:

More information

AIR CLEANERS Model MC 3000 OWNER S MANUAL CAUTION Read complete instructions before operating. Please file for future reference.

AIR CLEANERS Model MC 3000 OWNER S MANUAL CAUTION Read complete instructions before operating. Please file for future reference. AIR CLEANERS Model MC 3000 OWNER S MANUAL CAUTION Read complete instructions before operating. Please file for future reference. MODEL MC 3000 SPECIFICATION Input Volts: 208-230/430 VAC, 60Hz, 3 Phase

More information

Models CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" - 13C MAY FORM Page. Section - Q3

Models CHASSIS LUBE ELECTRIC GREASE PUMP Series C - 13C MAY FORM Page. Section - Q3 Models 94422 CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" MAY - 2004 FORM 403467 Section - Q3 Page - 13C 9.00" (229 mm) 13.75" (350 mm) 0.35" (9mm) Mounting Holes 4.76" (121 mm) 9.84" (250 mm) Do not use

More information

Troubleshooting. This section outlines procedures for troubleshooting problems with the operation of the system:

Troubleshooting. This section outlines procedures for troubleshooting problems with the operation of the system: Troubleshooting This section outlines procedures for troubleshooting problems with the operation of the system: 4.1 System Error Messages... 4-2 4.2 Prep Station Troubleshooting... 4-6 4.2.1 Adapter Not

More information

Auto-Level Troubleshooting (Old Platform) Electronic Control- Prior to 2009, Pressure Switch Control panel #s 2057, 2058, 2795, 2795B

Auto-Level Troubleshooting (Old Platform) Electronic Control- Prior to 2009, Pressure Switch Control panel #s 2057, 2058, 2795, 2795B Auto-Level Troubleshooting (Old Platform) Electronic Control- Prior to 2009, Pressure Switch Control panel #s 2057, 2058, 2795, 2795B This guide addresses the troubleshooting of electronic controls used

More information

ELECTRONIC POSITIVE AIR SHUTOFF

ELECTRONIC POSITIVE AIR SHUTOFF 12 January 2015 103675X Electronic positive air shutdown (I-00336) 1 ELECTRONIC POSITIVE AIR SHUTOFF 1036750 2007-2009 Dodge 6.7L 1036751 2010-2015 Dodge 6.7L 1036754 2008-2010 Ford 6.4L 1036755 2011-2014

More information

Operator's Manual. Models (¾") (1") (1½ ) (2 ) (3") (4") (6") (8")

Operator's Manual. Models (¾) (1) (1½ ) (2 ) (3) (4) (6) (8) OdisMatic Hydraulic Filter Series 851 Operator's Manual Models 85107 (¾") 85101 (1") 85115 (1½ ) 85102 (2 ) 85103 (3") 85104 (4") 85106 (6") 85108 (8") Content 1. Technical Specifications. 2. Materials.

More information

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2

SD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2 SD-03-832 Bendix E-10PR Retarder Control Brake Valve MOUNTING PLATE SUPPLY 4 PORTS ELECTRICAL AUXILIARY DESCRIPTION TREADLE RETARDER CONTROL SECTION EXHAUST DELIVERY 4 PORTS FIGURE 1 - E-10PR RETARDER

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

MAINTENANCE MANUAL DI 16

MAINTENANCE MANUAL DI 16 MAINTENANCE MANUAL DI 16 0.2-1.6% Press Ctrl + L for full screen 1 STANDARD INSTALLATION Inlet Outlet Optional accessories: Pressure regulator Solenoid valves Water meter Flow restrictor 200 Mesh/ 80 micron

More information

PAGE 1. TES Operation & Testing Guidelines: Tes Trouble shooting

PAGE 1. TES Operation & Testing Guidelines: Tes Trouble shooting PAGE 1 This document outlines questions to ask and components to check during TES troubleshooting. More detailed troubleshooting procedures are available in the TES Troubleshooting Guide. 1. Flow Light

More information

CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM 1988 Jeep Cherokee 1988 Cruise Control Systems JEEP CRUISE COMMAND All Models DESCRIPTION & OPERATION Jeep vehicles use an electro-mechanical servo system. The system consists of

More information

Cooling System. Table of Contents

Cooling System. Table of Contents Sub-Headings Safety 2 s 2 Cautions 2 Notes 2 Introduction 2 General Specifications 2 Engine 2 Coolant 2 Routine Maintenance 2 Hose Connections 4 Radiator, Charge Air and Heater Cores 4 Cooling System Leaks

More information

Consists of. Date:17/02/2011 Page 1/8

Consists of. Date:17/02/2011 Page 1/8 Consists of 470518 Qty. Product 4 1 DEFA Termina - interior heater with holder 1 1 DEFA Futura - time program controller/timer 3 1 DEFA MultiCharger 1203 - battery charger/relay 6 1 DEFA Extension cable

More information

Model CHASSIS LUBE ELECTRIC GREASE PUMP Series "C"

Model CHASSIS LUBE ELECTRIC GREASE PUMP Series C Model 94222 CHASSIS LUBE ELECTRIC GREASE PUMP Series "C" Indicates change MAY - 2004 FORM 403466 Section - Q3 Page - 12B 7.75" (197 mm) 12.6" (321 mm) 0.35" (9 mm) Mounting Holes 4.85" (123 mm) 8.85" (225

More information

LIPPERTCOMPONENTS, INC.

LIPPERTCOMPONENTS, INC. LIPPERTCOMPONENTS, INC. SCHWINTEK INWALL SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL Contents I. Controls 1-1 System components 1 1-1A versions C1 & C2 2 1-2 Motor wiring harness connections 3 1-3 Extend

More information

OPERATION MANUAL Electric Wire Wrapper TDWW501B

OPERATION MANUAL Electric Wire Wrapper TDWW501B OPERATION MANUAL Electric Wire Wrapper TDWW501B 4270 Airborn Drive Addison, Texas 75001 USA t. 972.248.1999 f. 972.248.1991 info@startinternational.com www.startinternational.com INTRODUCTION Thank you

More information

Page 1 of 29 Section 04-05: Suspension, Computer Controlled 1997 Town Car Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 05/16/2000 Suspension, Computer Controlled Inspection and Verification

More information

OPERATION MANUAL for MANUAL LEVELING SYSTEMS with square foot pads on jacks

OPERATION MANUAL for MANUAL LEVELING SYSTEMS with square foot pads on jacks OPERATION MANUAL for MANUAL LEVELING SYSTEMS with square foot pads on jacks Dewald manual system touchpad #140-1179 Visit us on the web at www.powergearus.com 82-L0377 REV.0B 2 TABLE OF CONTENTS Page 3:

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

Eminox Electronic Service Indicator

Eminox Electronic Service Indicator ESI Installation and Instruction Manual Eminox Electronic Service Indicator I n s t a l l a t i o n a n d I n s t r u c t i o n M a n u a l LITM004 ESI Installation and Instruction Manual Section Title

More information

Hydraulic pump HP-1. Type 1. Type 2

Hydraulic pump HP-1. Type 1. Type 2 The BEKA-MAX central lubrication pump model HP-1 is hydraulic actuated and has up to a maximum of independently operating lubricant outlets. A separate pump unit is required for each outlet. Three pump

More information

Automatic SingleLine Greasing System

Automatic SingleLine Greasing System Parts Manual Automatic SingleLine Greasing System D000144R04 YOUR EFFICIENCY IS OUR CHALLENGE All rights reserved. No part of this manual may be copied and/or published by means of printing, photocopying,

More information

CRS-D Powder Coating Booth with Reverse Jet Cleaning System

CRS-D Powder Coating Booth with Reverse Jet Cleaning System Operating Instructions CRS-D Powder Coating Booth with Reverse Jet Cleaning System CRS-D (J) 27 1 1 1 2 2 2 4 4 4 3 3 3 CRS-D Booth with Reverse Jet Cleaning System 1 10 2 3 9 12 11 11 1 Exhaust air unit

More information

LUBRICATION PUMP PMP CENTRAL LUBRICATION

LUBRICATION PUMP PMP CENTRAL LUBRICATION LUBRICATION PUMP USE OF LUBRICATION PUMP The lubrication pump is used as a pressure lubricant source for central lubricating systems with progressive distributor types BVA, PRA and PRB, for permanent,

More information

BOVIBOOSTER WDone & WDtwo

BOVIBOOSTER WDone & WDtwo BOVIBOOSTER WDone & WDtwo User Guide BBWDone BBWDtwo PowerDos15 D2NBAx D2NBDL Always wear suitable protective equipment when working on the BOVIBOOSTER Always disconnect the electrical supply when working

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS [1] Description: Tow Hitch Wire Harness Kit [2] Application: Nissan Rogue Note: Tow Harness application is limited to specific vehicle option packages that include tow harness

More information

Lubecore International Automated Lubrication System Inspection, Service & Repair - MLP/Spyder Pump MKI & MKI Rev-A

Lubecore International Automated Lubrication System Inspection, Service & Repair - MLP/Spyder Pump MKI & MKI Rev-A Lubecore International Automated Lubrication System Inspection, Service & Repair - MLP/Spyder Pump MKI & MKI Rev-A System Inspection MKI & MKI Rev-A Spyder System Check Check for: Conclusion of Review

More information

DISCONTINUED. OPERATORS MANUAL for SEMI AUTOMATIC RV SYSTEM. 82 L Rev. 0 September 3, Comment [KO1]:

DISCONTINUED. OPERATORS MANUAL for SEMI AUTOMATIC RV SYSTEM. 82 L Rev. 0 September 3, Comment [KO1]: OPERATORS MANUAL for SEMI AUTOMATIC RV SYSTEM 82 L0100 00 Rev. 0 September 3, 1999 Comment [KO1]: TABLE OF CONTENTS OPERATION AND MAINTENANCE...1 OPERATION CAUTION NOTES...1 BEFORE YOU OPERATE THE SYSTEM...2

More information

GLM SERIES CONTROL Users Manual Rev:

GLM SERIES CONTROL Users Manual Rev: GLM SERIES CONTROL Users Manual Rev: 808062 Connecting Power Page 2 Motor Terminal Wiring Diagrams Page 3 Getting Started / Setup Page 4 1. Obstruction Detection Devices Page 4 2. Checking Power and Direction

More information

1. AC VOLTS: Displays generator output in voltage. 2. AC FREQUENCY: Displays the speed of the generator set in Hertz.

1. AC VOLTS: Displays generator output in voltage. 2. AC FREQUENCY: Displays the speed of the generator set in Hertz. 1. AC VOLTS: Displays generator output in voltage. 2. AC FREQUENCY: Displays the speed of the generator set in Hertz. 3. AMMETER/PERCENT OF LOAD: Displays the load on the generator in amps or in percentage.

More information

Operating Instructions for Elevator Buffers type LP

Operating Instructions for Elevator Buffers type LP Operating Instructions for Elevator Buffers type LP 1 Scope of application The Elevator Buffer type LP is an energy dissipation type buffer according to EN 81-1/2, EN 81-20, EN 81-50 5.5 and therefore

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual Document 473681 Vari-Green Motor and Controls Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting to assemble,

More information

PARTS AND SERVICE MANUAL FOR LEVELING SYSTEMS WITH TOUCH PAD PART NUMBERS , , , , or no number at all

PARTS AND SERVICE MANUAL FOR LEVELING SYSTEMS WITH TOUCH PAD PART NUMBERS , , , , or no number at all PARTS AND SERVICE MANUAL FOR LEVELING SYSTEMS WITH TOUCH PAD PART NUMBERS 500089, 500105, 500210, 500456, 500535 or no number at all Visit us on the web at www.powergearus.com! 82 L0051 00 Rev. 3 1 WARNING

More information

Motor. Document # Vari-Green Motor and Controls. Table of Contents. Features, Operation, Wiring and Troubleshooting

Motor. Document # Vari-Green Motor and Controls. Table of Contents. Features, Operation, Wiring and Troubleshooting Document #473681 Vari-Green Motor and Controls Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting to assemble,

More information

BRAKE SYSTEM Return To Main Table of Contents

BRAKE SYSTEM Return To Main Table of Contents BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...

More information

TECHNICAL MANUAL GTB16N

TECHNICAL MANUAL GTB16N TECHNICAL MANUAL GTB16N 1/20 1. INTRODUCTION 1.1 Purpose 1.2 Before Service 1.3 Safety 1.3.1 Hazard Definitions 1.3.2 For Your Safety 1.4 Specifications & dimensions 1.5 Description 2. HYDRAULIC SYSTEM

More information

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL

SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location

More information

Common rail injection system

Common rail injection system Common rail injection system Pressure limiting valve The pressure limiting valve is located directly on the high-pressure fuel rail. Its function is to limit maximum pressure in the high-pressure fuel

More information

VC-4820 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL

VC-4820 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL 1. INTRODUCTION VC-4820 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL This MCU controlled Step Down DC-DC Converter has a digitally adjustable output in 0.2V increments. This

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual Document 47681 Vari-Green Motor and Controls Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,

More information

INSTALLATION AND MAINTENANCE OF TOP LOADING ARM

INSTALLATION AND MAINTENANCE OF TOP LOADING ARM INSTALLATION AND MAINTENANCE OF TOP LOADING ARM D TABLE OF CONTENTS 1. INTRODUCTION 04 2. SPECIFICATION OF THE REDLANDS LOADING ARM 04 3. INSTALLING THE LOADING ARM 3.1. Installation Procedures 05 4.

More information

Air-Assist Service Jack Max. Capacity: 10 Tons

Air-Assist Service Jack Max. Capacity: 10 Tons Form No. 565786 Parts List & Operating Instructions for: 1511B Air-Assist Service Jack Max. Capacity: 10 Tons 109 67 66 68 77 69 70 78 95 94 107 106 108 26 71 72 72 93 X L 65 75 92 91 90 89 88 87 86 85

More information

lubrication systems CME Electric pump for oil and soft grease volumetric

lubrication systems CME Electric pump for oil and soft grease volumetric lubrication systems CME Electric pump for oil and soft grease volumetric lubrication systems TABLE OF CONTENTS Table of contents 2 Description and technical data 3 Operation and technical data 4 Technical

More information

VS403 INSTRUCTIONS FOR: VACUUM AND PRESSURE TEST / BRAKE BLEEDING UNIT MODEL: SAFETY INSTRUCTIONS INTRODUCTION & CONTENTS. fig.1

VS403 INSTRUCTIONS FOR: VACUUM AND PRESSURE TEST / BRAKE BLEEDING UNIT MODEL: SAFETY INSTRUCTIONS INTRODUCTION & CONTENTS. fig.1 INSTRUCTIONS FOR: VACUUM AND PRESSURE TEST / BRAKE BLEEDING UNIT MODEL: VS403 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

More information

Electric Pump EP-1. Electric pump EP-1 with steel reservoir and pump element PE-120 V with manometer:

Electric Pump EP-1. Electric pump EP-1 with steel reservoir and pump element PE-120 V with manometer: The BEKA-MAX central lubrication pump model type EP-1 is electrical actuated and has a maximum of independently operating lubricant outlets. The pump is delivered with one pumping element as a standard,

More information

VEHICLE SECURITY SYSTEM INSTALLATION MANUAL

VEHICLE SECURITY SYSTEM INSTALLATION MANUAL VEHICLE SECURITY SYSTEM WITH REMOTE START & NETWORK INTERFACE INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! Before You Begin This system is intended

More information

Purging Air From Divider Block Lubrication Systems

Purging Air From Divider Block Lubrication Systems FROST ENGINEERING SERVICE Purging Air From Lubrication Systems A D I V I S I O N O F G E C S E Y S A L E S & S E R V I C E DESCRIPTION Divider block lubrication systems operate correctly only when all

More information

Model LA 4400 Time Delay OFF Controller

Model LA 4400 Time Delay OFF Controller ISIMET LA Series Model LA 4400 Time Delay OFF Controller Installation, Operation and Maintenance Manual Application: The Time Delay OFF Controller with integral 24-hr. programmable time clock operates

More information

TROUBLESHOOTING. 1. What is the model and serial number? If you don t know, how old is it? Give description.

TROUBLESHOOTING. 1. What is the model and serial number? If you don t know, how old is it? Give description. TROUBLESHOOTING There is excellent literature on our website: heatec.com. Look under TEC-NOTE. You will find our newest heater manual. This is full of information (complete with great pictures) on our

More information

CompAlube Automatic greasing system

CompAlube Automatic greasing system General Manual CompAlube Automatic greasing system your efficiency is our challenge General information Type of manual System Manual number General Manual CompAlube Automatic greasing system Publication

More information

LUBRICATION PUMP PMP CENTRAL LUBRICATION

LUBRICATION PUMP PMP CENTRAL LUBRICATION LUBRICATION PUMP APPLICATION The lubrication pump is used as a pressure lubricant source for central lubricating systems with progressive distributor types BVA, PRA and PRB, for permanent, regular lubrication

More information

Electric Fuel Pump FPM

Electric Fuel Pump FPM INSTRUCTION MANUAL Electric Fuel Pump FPM S1590, Rev B LISTED MOTOR FPM-12, FPM-24, FPM-115, FPM-220 Congratulations on purchase of this World Class Electric Fuel Pump! Elbow This is an Electric Fuel Pump.

More information

Vehicle Security System

Vehicle Security System Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting

More information

MD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version

MD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version MD10 Engine Controller Installation and User Manual for the MD10 Engine Controller. Full Version File: MartinMD10rev1.4.doc May 16, 2002 2 READ MANUAL BEFORE INSTALLING UNIT Receipt of shipment and warranty

More information

Operating Instructions. Angle Seat Control Valve. Type 7020

Operating Instructions. Angle Seat Control Valve. Type 7020 Operating Instructions Angle Seat Control Valve Type 7020 With: Digital Positioner Type 8048 Electro-pneumatic Positioner Type 8047 Pneumatic Positioner Type 8047 Version: 02/2006 Manual-7020e.doc Art.-No:

More information

SD Bendix SR-5 Trailer Spring Brake Valve DESCRIPTION PORTS. 1-1/2" or 3/4" NPT Spring Brake Reservoir Mounting (SPR BK RES)

SD Bendix SR-5 Trailer Spring Brake Valve DESCRIPTION PORTS. 1-1/2 or 3/4 NPT Spring Brake Reservoir Mounting (SPR BK RES) SD-03-4516 Bendix SR-5 Trailer Spring Brake Valve PRESSURE PROTECTION SR-5 IDENTIFICATION HOLE 1/4 NPT (2) COVER* FIGURE 1 DESCRIPTION 1/4 NPT TRAILER 1/4 NPT SR-5 TRAILER *SHOWN WITH OPTIONAL ANTI-COMPOUNDING

More information

HGM72 Automatic Generator Module OPERATING MANUAL Smartgen Electronic

HGM72 Automatic Generator Module OPERATING MANUAL Smartgen Electronic HGM72 Automatic Generator Module OPERATING MANUAL Smartgen Electronic Smartgen Electronic Equipment Co., Ltd No.28 Jinsuo Road Zhengzhou Henan Province P.R.China Tel: 0086-371-67988888/67981888 0086-371-67991553/67992951/67992952

More information

Parking brake Mechanical brake acting on rear wheels

Parking brake Mechanical brake acting on rear wheels 11 Brake System 11.1 General SPECIFICATIONS EJTC0010 Master cylinder Type Tandem type I.D. mm(in.) 20.64 mm (0.813 in.) Fluid level warning sensor Provided Brake booster Type Vacuum Boosting ratio 4.0

More information

18VDC ESB6 Series Cordless Screwdrivers Operation Manual

18VDC ESB6 Series Cordless Screwdrivers Operation Manual 18VDC ESB6 Series Cordless Screwdrivers Screwdriver Models : ESB6-8, ESB6-12, ESB6-15, ESB6-22 CAUTION - Please read, understand, and follow all operating and safety instructions in this manual before

More information

MLP2 - DUAL-BRANCH LUBRICATION SYSTEM

MLP2 - DUAL-BRANCH LUBRICATION SYSTEM - DUAL-BRANCH LUBRICATION SYSTEM TABLE OF CONTENTS 1 GENERAL SYSTEM DESCRIPTION...1 1.1 General information on automatic centralized lubrication system...1 2 SYSTEM DESIGN...1 3 SYSTEM OPERATION...1 4

More information

DISCONTINUED. OPERATORS MANUAL for MANUAL RV SYSTEM REV. 1 August, Comment [KO1]:

DISCONTINUED. OPERATORS MANUAL for MANUAL RV SYSTEM REV. 1 August, Comment [KO1]: OPERATORS MANUAL for MANUAL RV SYSTEM 81 1297 REV. 1 August, 1997 Comment [KO1]: TABLE OF CONTENTS OPERATION AND MAINTENANCE... 1 LEVELING PROCEDURES...2 RETRACTION PROCEDURES...3 RECOMMENDED FLUIDS...3

More information

CRD610 Automatic Fitting Inserter

CRD610 Automatic Fitting Inserter CRD610 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 1.2 LAST EDITED 12.12.2018 cleanroomdevices.com 1 Table of Contents Title Page. 1 Table of Contents...2 1.0 General Product & Safety Information....3

More information

LIPPERTCOMPONENTS, INC. HYDRAULIC SLIDEOUT AND HYDRAULIC LANDING GEAR (HLG) SYSTEM OPERATION AND SERVICE MANUAL

LIPPERTCOMPONENTS, INC. HYDRAULIC SLIDEOUT AND HYDRAULIC LANDING GEAR (HLG) SYSTEM OPERATION AND SERVICE MANUAL LIPPERTCOMPONENTS, INC. HYDRAULIC SLIDEOUT AND HYDRAULIC LANDING GEAR (HLG) SYSTEM OPERATION AND SERVICE MANUAL TABLE OF CONTENTS SYSTEM...... Warning...... Prior to Operation... Description..... Preventative

More information

OPERATING MANUAL Digital Diesel Control Remote control panel for WhisperPower generator sets

OPERATING MANUAL Digital Diesel Control Remote control panel for WhisperPower generator sets Art. nr. 40200261 OPERATING MANUAL Digital Diesel Control Remote control panel for WhisperPower generator sets WHISPERPOWER BV Kelvinlaan 82 9207 JB Drachten Netherlands Tel.: +31-512-571550 Fax.: +31-512-571599

More information

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit

INSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;

More information

Pressure chlorine changeover unit C 7520

Pressure chlorine changeover unit C 7520 BW 2 24 04 / 1 Content 1. Scope of delivery 2. Device description 3. Installation 4. Operation 5. Shutdown 6. Maintenance 7. Troubleshooting 1 Scope of delivery The chlorine gas changeover unit C 7520

More information

Progressive Central Lubrication Systems

Progressive Central Lubrication Systems Table of contents 4 Technical basics System description... 04-0-0-0 Construction, applications, advantages, function System design... 04-0-0-02 Design and installation of progressive systems Calculation

More information

Power Distribution System User s Manual. Model: PDS-100

Power Distribution System User s Manual. Model: PDS-100 Power Distribution System User s Manual Model: PDS-0 Section Page Product Overview... 1 I) General Information... 2 II) Important Safety Information... 2 III) Installation... 3 A) Materials Provided...

More information

Hydro-Sync Slide-Out System

Hydro-Sync Slide-Out System Hydro-Sync Slide-Out System SERVICE MANUAL Rev: 08.14.2018 Hydro-Sync Slide-out System Service Manual TABLE OF CONTENTS Safety Information 3 Product Information 3 Operation 4 Extending Slide-Out Room 4

More information

Operation Guide. Operation Guide. Winnebago Hydraulic Leveling Systems by Kwikee. Introduction. Table of Content WARNINGS

Operation Guide. Operation Guide. Winnebago Hydraulic Leveling Systems by Kwikee. Introduction. Table of Content WARNINGS Operation Guide 05/07 Kwikee #1422192 Rev. 0F Table of Content Page Introduction 1 Safety Information 1 Operation 2 Control Panel 3 Manual Leveling 3 Automatic Leveling 3 Remote Operation 4 Stabilizing

More information

WEBER CARBURETOR TROUBLESHOOTING GUIDE

WEBER CARBURETOR TROUBLESHOOTING GUIDE This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful

More information

2002 ENGINE PERFORMANCE. Self-Diagnostics - RAV4. Before performing testing procedures, check for any related Technical Service Bulletins (TSBs).

2002 ENGINE PERFORMANCE. Self-Diagnostics - RAV4. Before performing testing procedures, check for any related Technical Service Bulletins (TSBs). 2002 ENGINE PERFORMANCE Self-Diagnostics - RAV4 INTRODUCTION NOTE: Before performing testing procedures, check for any related Technical Service Bulletins (TSBs). To properly diagnosis and repair this

More information

MODUL-CONNECT 1.2. Owner s Manual. Modular, digital wiring and control system. Document Part Number MSMC Rev 9 (04/18)

MODUL-CONNECT 1.2. Owner s Manual. Modular, digital wiring and control system. Document Part Number MSMC Rev 9 (04/18) MODUL-CONNECT 1.2 Modular, digital wiring and control system Owner s Manual Document Part Number MSMC Rev 9 (04/18) Service Contact Information E-mail: info@modul-system.com Phone: +46 31 746 87 00 Web:

More information

# & Automatic Touchpad. # & Semi-Auto Touchpad. # Manual Touchpad

# & Automatic Touchpad. # & Semi-Auto Touchpad. # Manual Touchpad # 500629 & 140-1226 Automatic Touchpad # 500675 & 140-1231 Semi-Auto Touchpad # 500731 Manual Touchpad Parts and Service Manual for Hydraulic Leveling Systems with Touch Pad Part Numbers 500675, 140-1231,

More information

Demand Switch NEFA20 Plus. Installation Guide. Please read this entire guide before beginning the installation!

Demand Switch NEFA20 Plus. Installation Guide. Please read this entire guide before beginning the installation! Demand Switch NEFA20 Plus Installation Guide Please read this entire guide before beginning the installation! Supplied Parts Protective Covers DIN Mounting Rail NEFA20 Plus Mounting Rail Spacer Warning

More information

HGS SYSTEM Workshop Manual M103 01

HGS SYSTEM Workshop Manual M103 01 HGS SYSTEM Workshop Manual M0 0 HGS SYSTEM VERSION.0 EN/0-00 Autobusfabriek BOVA b.v. De Vest 9 5555 XL Valkenswaard The Netherlands Phone: + (0) 40 0846 Fax: + (0) 40 09477 E-mail: basis@bova.nl Website:

More information

04979, 04980, 04981, 04982, 04983, 04984, 39054, 39055, 39056, 39057, 39225, 81459,

04979, 04980, 04981, 04982, 04983, 04984, 39054, 39055, 39056, 39057, 39225, 81459, Hydraulic Bottle Jacks 04979, 04980, 04981, 04982, 04983, 04984, 39054, 39055, 39056, 39057, 39225, 81459, 82132. These instructions accompanying the product are the original instructions. This document

More information

Operators Manual SUREFIRE II Single Phase PDI - SLR (24VDC, 115VAC & 230VAC) r#3

Operators Manual SUREFIRE II Single Phase PDI - SLR (24VDC, 115VAC & 230VAC) r#3 Operators Manual SUREFIRE II Single Phase PDI - SLR (24VDC, 115VAC & 230VAC) 36412 r#3 Contents Precautions & Symbols...2 Manufacturer s Statement...2 General...2 Features...2 Operation...3-4 Technical

More information

3200NT Timer Service Manual

3200NT Timer Service Manual Service Manual Valve Serial Number Valve Position 1-LEAd 2-LAg 3-LAg 4-LAg IMPORTANT: Fill in pertinent information on page 3 for future reference. Table of Contents Job Specifications Sheet.....................................................................

More information

CRD600 Automatic Fitting Inserter

CRD600 Automatic Fitting Inserter CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.3 LAST EDITED 12.07.2018 cleanroomdevices.com 1 Table of Contents Title Page.. 1 Table of Contents. 2 1.0 General Product & Safety Information...3

More information