Big Blue 700 Series. Quick Specs. Diesel Engine-Driven Welder/AC Generator

Transcription

1 Big Blue 700 Series Issued April 2017 Index No. ED/5.6 Diesel Engine-Driven Welder/AC Generator Quick Specs Heavy Industrial Applications Pipe welding Mechanical contractor Construction Repair Processes Stick (SMAW) MIG (GMAW) Flux-cored (FCAW) RMD * Pulsed MIG (GMAW-P)* DC TIG (GTAW) Air carbon arc (CAC-A) Single weld mode 3/8-inch (9.5 mm) carbons Dual weld mode 1/4-inch (6.4 mm) carbons Output Range Single weld mode CC: A, CV: V Dual weld mode CC: A, CV: V Generator Output Rated at 104 F (40 C) Base model 4,000 watts continuous Deluxe model adds 3-phase, 20,000 watts continuous 1-phase, 12,000 watts continuous *Available only on Big Blue 700X Duo Pro SF model. The professional welder s choice designed with the professional in mind, the Big Blue 700 Series is the best for arc performance, ease of use and reliability. Big Blue 700 and 700X Duo Pro Multioperator work platform delivers two premium arcs (up to 400 amps each) allowing welding operators to work independently with no arc interaction. NEW! Big Blue 700X Duo Pro SF Improve productivity and quality with advanced RMD and pulsed MIG processes with the FieldPro Smart Feeder. Double the amperage output. Deluxe models have a parallel switch that combines both independent outputs to a single side. This provides a safe and easy way to run large electrodes, stud weld or carbon arc gouge. Increase profits with this multi-arc machine by completing your most demanding jobs in half the time compared to conventional enginedriven welders. With two arcs in one engine drive, fewer machines are required for a job. Low OCV stick (VRD) reduces the open-circuit voltage to 15 volts when the welding power source is not in use. This feature is now built in for increased operator safety without compromising arc start performance. Big Blue 700 Duo Pro Heavy-duty low-speed industrial diesel engine is designed to operate over 10,000 hours before the first basic overhaul. Backed by worldwide support and service. Thermal overload protection prevents machine damage if duty cycle is exceeded or airflow is blocked. Big Blue 700X Duo Pro All models are EPA Tier 4i Compliant NEW! Big Blue 700X Duo Pro SF Independent generators (Deluxe models only) provide the flexibility, dependability and reliability you need to get the job done right. One 4,000-wattcontinuous, single-phase generator is fully indepen - dent of weld output. Power is available anytime the engine is running, even while welding! The second generator has 20,000 watts continuous available for your high power needs. Welder/generator is warranted by Miller for three years, parts and labor. Engine is warranted separately by engine manufacturer. Miller Electric Mfg. Co. An ITW Welding Company 1635 West Spencer Street P.O. Box 1079 Appleton, WI USA Equipment Sales US and Canada Phone: FAX: International Phone: International FAX: MillerWelds.com

2 Big Blue 700 Series Features Simple-to-set controls require no elaborate procedure just select process and weld! Meter maintenance displays Fuel gauge Hour meter function Oil change interval High coolant temperature and low oil pressure shutdowns Low fuel shutdown engine shuts down before system runs out of fuel, making restarts easy Big Blue 700 Duo Pro Big Blue 700X Duo Pro (Deluxe model shown) Simple paralleling switch makes switching from a single operator to dual operators a breeze. Weld up to 400 amps per side when set up in dual-operator mode, or up to 800 amps in singleoperator mode. Deluxe models only. Standard features include stick, MIG, flux-cored, Lift-Arc TIG, digital preset weld meters, output contactor control and automatic idle. Deluxe models add parallel switch, three-phase auxiliary generator power, intake manifold heater and oil pan heater. What Makes Miller Industrial Engine Drives So? Superior Circuit Board Design Our critical circuit boards are engineered to carry low power and low heat to reduce thermal stress and minimize expansion and contraction. In contrast, our competitor s boards carry high power and high heat, making them more vulnerable to failure. Rigorous Testing for Tough, Real-World Conditions To prove our machines go to the limit, Miller industrial engine drives are put to the test in very extreme environmental conditions. Airborne dust and sand. Critical components are exposed to abusive airborne particles in a special testing chamber for weeks, helping make sure they ll operate while facing extreme levels of dirt, dust or sand on the jobsite. Humidity and corrosion. Inside our Houston testing room, critical components are subjected to extended moisture and corrosive salt exposure to ensure they ll run even when exposed to humid climates, corrosive coastal environments, and driving rain. Temperature extremes. Miller industrial engine drives are tested to ensure performance in scorching heat. All Miller engine-driven machines are weld rated at 104 degrees Fahrenheit, but actual tests are conducted up to 122 degrees Fahrenheit to assure peak performance. Jobsite/over-the-road abuse. Miller industrial engine drives are shaken for hours on transportation bed simulators, subjected to severe vibration, and test-dropped and jerked to ensure they ll withstand the stresses that can shut down competitive machines. Continuous operation. Miller industrial engine drives run day and night, in all weather conditions, to assure they ll perform without interruption in the field. 2

3 Big Blue 700 Series Features NEW! SF Model Additional Features Advanced RMD and pulsed MIG processes are now available in an engine driven welder/generator. Discover increased productivity, quality, and improved efficiency in field welding with the new Big Blue 700X Duo Pro SF with FieldPro Smart Feeder. FieldPro Smart Feeder FieldPro Smart Feeder delivers excellent RMD and pulsed MIG welding up to 200 feet away from the power source with no control cables twice the distance previously possible. RMD and pulsed MIG processes help reduce weld failures and eliminate backing gas on some stainless and chrome-moly pipe-welding applications. LINE -X cover is workbench tough and provides superior impact, corrosion and abrasion protection. Durable design reduces downtime. Impactresistant case and the elimination of feeder control cables provide a solid solution to last in harsh environments. Full remote control at the weld joint. Simply connect standard weld cables in-line with the FieldPro Smart Feeder and you re ready to go! FieldPro Smart Feeder Specifications Simple-to-set controls have integrated support for Smart Feeder, simply turn the knob to either MIG VS or FCAW VS for optimal performance. Big Blue 700X Duo Pro SF ( ) with FieldPro Smart Feeder ( ), Bernard PipeWorx 300 MIG gun (195400), work cable and clamp (195458) and weld cable extensions (195456). Input Power Operates on open-circuit voltage and arc voltage: VDC/110 max. OCV Input Welding Circuit Rating 275 A at 60% duty cycle Wire Feed Speed ipm ( m/min.) dependent on arc voltage Wire Diameter Capacity in. ( mm) Maximum Spool Size Capacity 12 in. (305 mm), 33 lb. (15 kg) Dimensions H: 18 in. (457 mm) W: 13 in. (330 mm) D: 21.5 in. (546 mm) Net Weight 50 lb. (23 kg) Lift-Arc TIG with Auto-Stop Arc Start with Lift-Arc Touch or scratch Workpiece Shielding gas Arc Lift at any angle Shielding gas Reduces or eliminates sticking Reduces or eliminates electrode/work contamination Low opencircuit voltage Arc End with Auto-Stop While welding Arc Workpiece Shielding gas Lift up until arc ends For Auto-Stop, lift up to terminate arc Arc ends without flare Move back down to maintain gas coverage Eliminates need for a remote control Maintains shielding gas coverage Eliminates tungsten and workpiece contamination Eliminates unwanted arc strikes outside the weld area 3

4 Specifications (Subject to change without notice.) Weld Mode/ Process Output Mode Weld Output Range Weld Output Rated at 104 F (40 C) Max. Open- Circuit Voltage Generator Power Output Rated at 104 F (40 C)** Dimensions Weight CC/DC (Stick/TIG) CV/DC (MIG/FCAW) Separate (dual outputs) Paralleled (combined) Separate (dual outputs) A (each side) A V (each side) 300 A at 28 VDC, 100% duty cycle* (each side) 400 A at 36 VDC, 40% duty cycle* (one side only) 500 A at 34 VDC, 100% duty cycle 700 A at 24 VDC, 60% duty cycle 300 A at 28 VDC, 100% duty cycle* (each side) 400 A at 34 VDC, 40% duty cycle* (one side only) 85 VDC 4,000 watts continuous 1-phase, 34/17 A, 120/240 VAC, 50/60 Hz while welding Optional generator power for Deluxe models 3-phase: 20 kw continuous OR 1-phase: 12 kw continuous H: 43 in. (1,092 mm) W: 28.5 in. (724 mm) D: in. (1,654 mm) Add 7 in. (178 mm) to height for exhaust pipe Net: 1,729 lb. (784 kg) Ship: 1,761 lb. (799 kg) Add 165 lb. (75 kg) when fuel tank is full Paralleled (combined) V 500 A at 34 VDC, 100% duty cycle 700 A at 24 VDC, 60% duty cycle *Meets NEMA and IEC ratings. **Will operate either 60 hertz or 50/60 hertz power tools, lights, etc. Certified by Canadian Standards Association to both the Canadian and U.S. Standards. Engine Specifications (Engines warranted separately by the engine manufacturer.) Engine Brand Features HP Type Engine Speeds Sound Levels at Rated Output, 23 ft. (7 m) Capacities Automatic Engine Shutdown Deutz D2011L04i EPA Tier 4i compliant 48.6 Direct-injected four-cylinder, air/oil-cooled industrial diesel Idle: 1,350 rpm Weld: 1,800 rpm Idle: 67.9 db (93 Lwa) Weld: 74.7 db (100 Lwa) Fuel: 25 gal. (95 L) Oil: 9 qt. (8.5 L) Coolant: integrated oil Low oil pressure, high coolant temperature, low fuel level Performance Data Fuel Consumption Curve Paralleled arc Dual arcs Simultaneous Welding and Power (Deluxe Models) Total Aux. Power Available (Watts) Weld Amperes 1-Phase or 3-Phase No Weld Output 12,000 20,000 Liters/Hr US Gal/Hr Single arc 200 A 300 A 400 A 11,500 6,000 1,000 11,000 6,500 1, Idle DC Weld Amperes at 100% Duty Cycle 4

5 Function Guide 1. Weatherproof Lexan nameplate is super durable and resists cracking and fading. Color coded for ease of operation. 2. Operator controls. Independent controls for multi-arc welding. A controls are for single operator and B controls are for a second operator. 3. Self-calibrating digital weld meters with fault code indication display preset or actual weld parameters. 4. Adjustable arc control adjusts DIG when process control is in stick mode and adjusts inductance when process control is in FCAW or MIG mode. The amount of DIG determines how much amperage (heat) varies with stick arc length. Inductance determines the wetness of the weld puddle Amperage/voltage adjust control 6. Hot Start provides positive stick electrode starts making it easy to start all types of electrodes and it also works great for bead tie-ins. 7. Great FCAW/MIG performance and arc starts make the Big Blue 700 Duo Pro arc the best in its class. Easy to run all wires from.023-inch solid wires to large-diameter 5/64-inch flux-cored wires. 8. Lift-Arc TIG with Auto-Stop. See page 3 for benefits Standard 14-pin receptacle for simple connection of remote controls and wire feeders. Includes Auto Remote Sense which automatically switches from panel to remote amperage/voltage (A/V) control with remote connected. Eliminates confusion of a panel/remote switch. 10. Weld output terminals 11. Separate/parallel switch (only available on Deluxe models). Use switch to select single operator mode (A) or dual operator mode (A/B). 12. Meter maintenance displays show fuel level, engine hours, oil change interval and high temp/ low pressure/low fuel shutdown information. 13. Engine oil pressure gauge. Engine stops if pressure is below 22 psi (1.5 bar). 14. Engine coolant temperature gauge. Engine stops if temperature exceeds 284 F (140 C). 15. Glow plugs assist in cold weather starting (standard on Deluxe models). 16. Engine control switch is used to start engine and then select between auto idle and high speed lock. 11 International Deluxe model Deluxe model with USA receptacles and circuit breakers International Deluxe model receptacles and circuit breakers A, 120 V receptacles with ground fault V circuit breaker and 240 V earth leakage circuit breaker A, 400 V three-phase receptacle (For matching plug, order ) A, three-phase circuit breaker and 240 V circuit breakers A, 120/240 V receptacles (For matching plugs, order for 120 V and for 240 V.) Deluxe model with USA receptacles and circuit breakers A, 120/240 V receptacle (For matching plug, order ) A, 240 V, three-phase receptacle (For matching plug, order ) A, 120 V receptacles with ground fault A, 240 V receptacles A, 120 V circuit breakers A, 240 V circuit breaker A circuit breaker 5

6 Genuine Miller Accessories Female Receptacle Full KVA Adapter Cord Field NEMA 14-50P to NEMA 6-50R. Adapts engine drive 120/240 V plug to common Millermatic and Spectrum 240 V plug. Full KVA Plug Kit Field phase, 120/240 V, 50 A plug (NEMA 14-50P) phase, 240 V, 50 A plug (NEMA 15-50P) International Plugs Field phase, 120 V, 16 A plug phase, 240 V, 16 A plug phase, 400 V, 32 A plug Cold Weather Starting Kits* Field volt intake manifold heater volt oil pan heater element. *For extreme cold weather both starting aids can be used in conjunction. These aids are standard on Deluxe model. Engine Filter Kit Field Includes all filters required for proper engine maintenance. Oil filter, primary and secondary fuel filter, and primary air filter. Spark Arrestor Kit Field Prevents particles from leaving the muffler that could potentially start a fire. Mandatory when operating on California grasslands, brush, or forest-covered land, and in all national forests. For other areas, check your state and local laws. Meets U.S. Forest Service standard B. FA-1D Lockable Flame Arrestor Fuel Cap Field Fuel cap can be padlocked to prevent vandalism. A built-in flame arrestor prevents flames or sparks from entering the fuel tank. Vandalism Lockout Kit Field Lockable hinged steel panels cover and protect name plate gauges and ignition switch (padlock included). Cable Holder Field Saddle-bag-style cable holder. Convenient wraparound storage of coiled cable for transportation. Stores 100 feet of 2/0 cable on each side. Note: For best results do not weld when cable is coiled! Protective cover cannot be used with cable holder. Protective Cover Field Blue water-resistant canvas cover resists stains and mildew, and protects the finish of your welder. Note: Protective cover cannot be used with cable holder. MIG (GMAW) or Flux-cored (FCAW) SuitCase X-TREME 8VS Wire Feeder With Bernard BTB Gun 300 A SuitCase X-TREME 12VS Wire Feeder With Bernard Dura-Flux gun Lightweight, voltage-sensing wire feeders include secondary contactor, gas valve, drive roll kit and gun. See literature M/6.42. SuitCase 12RC Wire Feeder Lightweight and flexible enough to run a variety of wires up to.062-inch diameter. Includes remote voltage control, drive roll kit and Bernard BTB Gun 300 A. See literature M/6.5. FieldPro Smart Feeder For use with Big Blue 700X Duo Pro SF model only. See page 3 for more information. MIG (GMAW)/Flux-cored (FCAW) Guns See Bernard literature SP-BTB for BTB air-cooled MIG guns, and SP-DF for Dura-Flux self-shielded flux-cored guns. PipeWorx Memory Cards For use with FieldPro Smart Feeder only Blank Card Used to store weld programs System Software For free download, visit MillerWelds.com Calibration Used to calibrate the PipeWorx System. For free download, visit MillerWelds.com Inconel Pulsed MIG,.045-inch diameter wire, 100% argon Range Locks Provides ability to set nominal parameter values and ranges for wire feed processes Accu-Power Displays instantaneous power during welding to meet the new ASME requirement for calculating heat input on complex waveform processes (RMD and pulsed MIG) Trigger Select/Hold Option Enables trigger select while welding to change processes and parameters without stopping. Stick (SMAW) Welding Weld Leads 2/0 Stick Cable Set, 50 ft. (15 m) Consists of 50-foot (15 m) 2/0 electrode cable with holder, and 50-foot (15 m) work cable with clamp. 350 A, 100% duty cycle. 2/0 Stick Cable Set, 100/50 ft. (30.5/15 m) Consists of 100-foot (30.5 m) 2/0 electrode cable with holder, and 50-foot (15 m) work cable with clamp. 300 A, 100% duty cycle. AC TIG (GTAW) Welding Dynasty 210 Series For portable AC/DC TIG. See literature AD/

7 Genuine Miller Accessories (Continued) Plasma Cutting Spectrum 375 X-TREME and 625 X-TREME shown. Spectrum 375 X-TREME See literature PC/9.2. Spectrum 625 X-TREME See literature PC/9.6. Spectrum See literature PC/9.8. The Spectrum 375 X-TREME and 625 X-TREME come complete with protective X-CASE (not shown). Remote Controls Wireless Remote Hand Control For remote current, voltage and contactor control. Receiver plugs directly into the 14-pin receptacle of Miller machine. 300-foot (91.4 m) operating range. Wireless antenna kit recommended. Wireless Antenna Kit Optional when improved reception is desired. RHC-14 Hand Control Miniature hand control for remote current, voltage and contactor control. Dimensions: 4 x 4 x 3.25 inches (102 x 102 x 82 mm). Includes 20-foot (6 m) cord and 14-pin plug. Extension Cables for 14-Pin Remote Controls or 24 VAC Wire Feeders ft. (7.6 m) ft. (15.2 m) ft. (24.4 m) Trailers and Hitches (Note: Trailers are shipped unassembled.) Mounting Specifications H 4 holes A B Front panel C 4 West Four-Wheel Steerable Off-Road Trailer A heavy-duty 2,550-pound (1,157 kg) capacity trailer designed for use in mines, quarries, and other rough terrain. Has narrow 22-foot (6.7 m) turning radius. Includes 3-inch (76 mm) lunette eye, universal hitch and safety chains. HWY-225 Trailer A 2,700-pound (1,225 kg) capacity highway trailer with welded steel tubing frame, heavy-duty axle with roller bearing hubs and leaf-spring suspension. Includes jack stand, fenders, lights, and dual hitch with 2-inch (50 mm) ball hitch and 3-inch (76 mm) lunette eye. Cable Tree Provides an area to conveniently wrap weld cables and extension cords. Dual Hitch inch (50 mm) ball hitch and 3-inch (76 mm) lunette eye in one reversible assembly. A in. (757 mm) B in. (699 mm) C. 1 in. (25 mm) D in. (244 mm)* E in. (1,181 mm)* F. 56 in. (1,422 mm)* G in. (1,654 mm) H..562 in. (14 mm) dia. D Height: 43 in. (1,092 mm) to top of cover Add 7 in. (178 mm) to height for exhaust pipe (Exhaust measurement subject to change.) Width: 28.5 in. (724 mm) (mounting brackets turned in) in. (781 mm) (mounting brackets turned out) Depth: in. (1,654 mm) *With mounting brackets in center position. Dimensions vary with location of mounting brackets. E F G Trailer Specifications (Subject to change without notice.) Model Gross Axle Weight Rating Gross Vehicle Weight Rating Net Payload Height of Bed Road Clearance Track (Center to center of tires) Standard Tires (Standard rating or P-size rating) Dimensions Net Weight 4 West 2,000 lb./axle (907 kg/axle) 3,000 lb. (1,361 kg) 2,550 lb. (1,170 kg) in. (540 mm) 8 in. (203 mm) in. (1,403 mm) B78-13 Length: 91 in. (2,311 mm)* Width: in. (1,556 mm) 430 lb. (195 kg) HWY-225 3,500 lb. (1,588 kg) 2,999 lb. (1,360 kg) 2,700 lb. (1,225 kg) 19 in. (483 mm) 7.5 in. (191 mm) 50 in. (1,270 mm) ST175/80R-13 Load Range D Length: in. (2,680 mm) Width: 56.5 in. (1,435 mm)** 280 lb. (127 kg) *Does not include tongue. **Width at outside of fenders. 7

8 Ordering Information Equipment and Options Stock No. Description Qty. Price Big Blue 700 Duo Pro Deluxe model with 20 kw of 240-volt 3-phase power, parallel switch, EPA Tier 4 Interim compliant engine intake manifold heater and 120-volt oil pan heater Big Blue 700X Duo Pro International base model EPA Tier 4 Interim compliant engine International Deluxe model with 20 kw of 400-volt 3-phase power, parallel switch, intake manifold heater and 120-volt oil pan heater Big Blue 700X Duo Pro SF International Deluxe Smart Feeder compatible model with EPA Tier 4 Interim compliant engine 20 kw of 400-volt 3-phase power, parallel switch, intake manifold heater and 120-volt oil pan heater Field Accessories Full KVA Adapter Cord Full KVA Plug Kit phase, 120/240 V, 50 A phase, 240 V, 50 A International Plugs phase, 120 V, 16 A phase, 240 V, 16 A phase, 400 V, 32 A Cold Weather Starting Kit volt intake manifold heater volt oil pan heater Engine Filter Kit Includes air, oil and fuel filters Spark Arrestor Kit FA-1D Lockable Flame Arrestor Fuel Cap Padlock NOT included Vandalism Lockout Kit Lockable front control panel Cable Holder Stores up to 200 feet of 2/0 cable Protective Cover Canvas cover will not fit over machine with cable holder attached MIG/Flux-Cored Welding SuitCase X-TREME 8VS With Bernard BTB Gun 300 A. See literature M/6.42 SuitCase X-TREME 12VS With Bernard Dura-Flux gun. See literature M/6.42 SuitCase 12RC With Bernard BTB Gun 300 A. See literature M/6.5 FieldPro Smart Feeder For use with Big Blue 700X Duo Pro SF model only. See literature PWS/6.0 MIG (GMAW) and Flux-Cored (FCAW) Guns See Bernard literature SP-BTB and SP-DF Stick Welding Leads /0, 350 A, 100% duty cycle, 50 ft. (15 m) stinger, 50 ft. (15 m) work clamp /0, 300 A, 100% duty cycle, 100 ft. (30.5 m) stinger, 50 ft. (15 m) work clamp TIG Welding Dynasty Basic controls for AC/DC TIG/stick, V. See literature AD/4.81 Dynasty 210 DX Full feature controls for AC/DC TIG/stick, V. See literature AD/4.81 Plasma Cutting Spectrum 375 X-TREME Includes X-CASE. See literature PC/9.2 Spectrum 625 X-TREME Includes X-CASE. See literature PC/9.6 Spectrum See literature PC/9.8 Remote Controls See page 7 Trailers and Hitches 4 West Four-Wheel Steerable Trailer Trailer with lunette eye, universal hitch and safety chains. For off-road use HWY-225 Trailer Trailer with lights, fenders and dual hitch. For highway use Cable Tree Trailer-mounted cable holder for HWY-225 Dual Hitch Combination 2-inch (50 mm) ball hitch and 3-inch (76 mm) lunette eye in one reversible assembly for HWY-225 Date: Total Quoted Price: Distributed by: 2017 Miller Electric Mfg. Co.