Belt-Driven Fan Replacement Kit Installation
|
|
- Shon Johnston
- 6 years ago
- Views:
Transcription
1 Disconnect the battery while you install this kit. Remove the two intake air ducts. See Picture BDFK1. Remove two 10mm bolts at the top of the radiator, and lift off the upper radiator fan shroud. See Picture BDFK2.
2 Loosen and remove the Power Steering Belt. Two 13mm bolts and loosen the nut on the threaded adjuster if you have one. See Picture BDFK3. Loosen and remove the Air Pump/Fan belt. Two 13mm bolts, and loosen the nut on the threaded adjuster if you have one. See Picture BDFK4.
3 Remove three 13mm bolts that hold the Fan Assembly to the front of the engine, and lift out the fan assembly. See Picture BDFK5. Remove the two 6mm Allen bolts from the upper radiator mounts as shown in Picture BDFK7. This will allow the radiator to pivot on the lower mount a little bit. The radiator does not have to come out.
4 INSTALLING THE NEW FAN Note there are 4 mounting holes at the base of your new fan shroud. In the bag with your fan mounts, locate the neoprene foam squares. Place one square of neoprene foam anti-vibration material over each hole in the fan shroud, so that the foam will be trapped between the fan and the radiator when the radiator is mounted. Peel off the cover to expose the sticky surface. Be sure to line up the holes. Position the fan behind the radiator. It fits inside the lower shroud for the 928, and right up against the radiator core. There is a flat spot in the shroud that should be placed on top as shown.
5 Now attach the fan to the radiator. The fan mounts are installed from the engineside of the fan pointing forward to the front. Push a fan mount through the hole in the radiator shroud, through the foam square you previously placed, through the radiator, and secure on the other side with the clip on fastener. Cut off the extra so it does no interfere with the air conditioning core when we stand the radiator back up. INSTALLING THE TEMP SENSOR/FAN SWITCH Place the billet temp sender over the upper radiator hose and mark where you are going to cut it. See Picture BDFK12.
6 Jack up the car at the right front jacking point. This will make the upper radiator hose the high point in your cooling system and you will loose very little coolant when you cut the hose. Cut the upper radiator hose where you marked it - removing an amount equal in width to the center section of the billet temp sender unit. Slide the two hose clamps provided with the kit onto the hose, and insert the billet temp sender unit. Tighten the clamps. See Picture BDFK13. NOTE: Rubber hoses stretch with age, temperature, and pressure. If your upper radiator hose is a lot wider than our billet temp sender unit, it means it has weakened and stretched out. It needs to be replaced. If you notice this call us at 928 Motorsports, we keep this hose in stock just for this occurrence. Remove the plastic cover (s) from the forward battery post. See Picture BDFK13. Open about 2 inches of the wire loom as shown in Picture BDFK14.
7 Now we will install the fan relay and wiring harness supplied. The instructions on the following pages refer to this Picture and the notations below R = Relay SP = Switched Power TS = Temp Switch P = Power G= Ground Wires (2) FC = Fan Connector FH = Fuse Holder
8 Find the Red wire with a White stripe and place the blue electrical tap over it. Squeeze it shut with a pliers as shown to complete the connection. Insert a 12v test lamp into the end of the blue electrical tap you just installed and test it. It should have power when the ignition is ON, and no power when the ignition is OFF. Plug the White wire referred to as SP into the wire tap as shown in BDFK 16
9 Find the 2 black wires (G) with ring terminals on the end of them and place under the grounding bolt As shown in BDFK17. You may also use one of the headlamp adjustment nuts located in that vicinity To mount your ground wires. Confirm that the battery is still disconnected before this step. Then unthread the brass battery post as shown in BDFK 18 and place the red wire (P) under it. Re-install the brass battery post.
10 Confirm that there is a 25 amp fuse in the fuse holder FS. Form the wiring harness so that it lies down neatly next to the OEM wires and hold it in place with the small black cable ties provided. It is not necessary to mount the Relay. Re-install the plastic cover over the battery post area, if any. Plug the Fan Connector (FC) into the matching receptacle on the fan. Connect the two remaining bullet connectors to the Temp Switch TS as shown. They can connect to either post, in any order.
11 Tie the electrical wiring down with more of the small cable ties provided as in BFK21. Install the air pump belt provided with the kit and tighten. Put the two 6mm bolts back into the upper radiator mounts and tighten them down. Re-install the upper radiator shroud, taking care not to snag or cut the electric fan wiring you just installed. Top-off your radiator coolant to replace whatever dropped when you cut your hose, and re-connect your battery.
12 The finished installation should look like the picture below. TESTING THE INSTALL: Start your engine and check for leaks. Add radiator fluid to the coolant reservoir to replace any that may have come out when you cut the upper radiator hose. The new electric fan will not come on right away. It only comes on at 185 degrees F, and shuts off at temps below that also. The water enters the radiator through the upper radiator hose, so the temp sensor you have installed will be the first thing to notice the temperature rising. The new electric fan will come on only after the engine warms up. This may take several minutes at idle, or take the car for a short drive to warm it up faster. Call if you have any questions!
SHELBY GT500
2007-2009 SHELBY GT500 Removal of Factory Unit WARNING: 1. Radiator fluid must be handled properly. Please observe local ordinances with regards to handling and disposal. 2. Allow vehicle and components
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationSR Performance Aluminum Radiator - Manual (96 4.6L)
SR Performance Aluminum Radiator - Manual (96 4.6L) Tools needed 1. Large and small pair of pliers 2. 8mm and 10mm deep socket and extensions 3. Spare Rags 4. Large Drain Pan 5. Funnel with small opening
More information2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions
Page1 James Barone Racing Aftermarket Parts and Accessories 2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More information97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS
92RC60500 97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS Congratulations on your purchase of a new Rough Country 2 /3 Body Lift. We are committed to providing you with the best product available for the best
More informationSECTION 1D1 M162 ENGINE COOLING
SECTION 1D1 M162 ENGINE COOLING CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More information2015+ WRX/STI RADIATOR SHROUD
2015+ WRX/STI RADIATOR SHROUD Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket performance
More informationInstallation Instructions for C & R Heat Exchanger Removal of Factory Unit
Installation Instructions for C & R Heat Exchanger Removal of Factory Unit Remove the 8 clips that retain the upper radiator shroud. Remove the shroud. Remove the coolant tank cap from the heat exchanger
More informationOUT FRONT ELECTRIC HYDRAULIC (W/E-47H) FOR STRAIGHT TRIPEDGE PLOWS (PULL AWAY MOUNTINGS)
80052 March 6, 1995 OUT FRONT ELECTRIC HYDRAULIC (W/E-47H) FOR STRAIGHT TRIPEDGE PLOWS (PULL AWAY MOUNTINGS) ITEM STOCK DESCRIPTION QTY. 51 15759 LIFT UNIT (E-47H) 1 52 817000 020 10" CYLINDER 2 53 15370
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More information21511 Commercial Light Kit Part # Qty Description
21511 Commercial Light Kit Part # Qty Description * 1 Plug in 21563 1 Battery Cable, 90" 8324 6 Cable Ties, 3/16" x 14" 21651 3 Split Rubber Grommet 21652 3 Rosebud Clip -.413/.500 21288 1 Blade Terminal
More information2013 Kia Optima L4-2.0L Turbo
1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted
More informationADM Performance 6079 Mapleshade Lane Dallas, Texas (214)
1) Disconnect Battery Ground 2) Raise front end of Vehicle FAN INSTALL INSTRUCTIONS 3) Remove lower Radiator hose and drain coolant into a pan. (you will reuse coolant later) 4) Remove Air Intake piping
More informationC FORD F250 / F L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY
EXHAUST BRAKES C40019 1999-2003 FORD F250 / F350 7.3L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY Getting Started Thank you and congratulations on your purchase of a Pacbrake exhaust retarder.
More informationIncluded parts: 1 - HSM Billet Aluminum Throttle Body Adapter 1-5-Ply Stainless-Reinforced Hose Replacement 2 - Stainless T-bolt Clamps STEP 1
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationB5 A4 1.8t Front Mount Intercooler Install Instructions
B5 A4 1.8t Front Mount Intercooler Install Instructions Only work underneath your vehicle after properly supporting it with adequate jack stands on a flat surface. NEVER work under a vehicle only supported
More informationInstallation Instructions. Lightning Force Performance. Mont Belvieu, texas H Phone: Fax:
,/ -.. ifp Electric Fan Installation Instructions,,'i ", ->- ~f~:';, ~';; ~.'7'" Lightning Force Performance PO Box 497\3207 KatWeen ṙ I Mont Belvieu, texas 77580.,. H Phone:281-38 5-5339 Fax:281-5 76-5650
More informationMishimoto Performance Aluminum Mustang Radiator - Manual - (94-95 GT/Cobra/V6) - Installation Instructions
Mishimoto Performance Aluminum Mustang Radiator - Manual - (94-95 GT/Cobra/V6) - Installation Instructions The below installation instructions work for the following products: Mishimoto Performance Aluminum
More informationBMW 2002 M42 Swap Notes-THIS IS NOT FINISHED
BMW 2002 M42 Swap Notes-THIS IS NOT FINISHED This document is to help those that want to install an m42 into a BMW 2002. It is based around an e30 engine, trans, and wiring. You can use the e36 block/head/wiring
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More information2016+ NISSAN TITAN XD
PARTS LIST AND PARTS INCLUDED 1PC MISHIMOTO INTERCOOLER 2PC SILICONE BOOTS WITH DURACORE TECHNOLOGY 4PC CONSTANT-TENSION T-BOLT CLAMPS 2PC ALUMINUM SPACERS MOUNTING HARDWARE CAUTION Never work on the cooling
More informationWPS-104 Heater Installation Instructions For 500EFI, 700 XP, & Crew Applications
WPS-104 Heater Installation Instructions For 500EFI, 700 XP, & Crew Applications ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A RANGERWARE WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater
More informationFlex Fuel Bluetooth Kit WRX install instructions
Delicious Tuning 1948 Don Lee Place Suite #7 Escondido, CA 92029 408-480-0995 BJP Rev: 1.0 Date: 10/1/15 FFBT parts: (1) Ethanol Content Analyzer Module (1) Ethanol Content Analyzer Sensor (1) Sensor Bracket
More informationHard Brake Pedal on Cold Starts at High Altitudes (Install Auxiliary Vacuum Pump) # (04/27/2006)
Document ID# 1822803 2005 Cadillac CTS Subject: Models: Hard Brake Pedal on Cold Starts at High Altitudes (Install Auxiliary Vacuum Pump) #06-05-22-003 - (04/27/2006) 2005-2006 Cadillac CTS with 2.8L Engine
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More information1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION
by Randy Irwin 1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 30 years. He is a wizard at creating,
More informationMishimoto Performance Aluminum Radiator w/ Stabilizer - Manual (97-04 GT, Mach 1; Cobra)
Mishimoto Performance Aluminum Radiator w/ Stabilizer - Manual (97-04 GT, Mach 1; 97-01 Cobra) Installed on: 2000 Mustang GT (manual transmission) Tools: 8mm socket 10mm socket 13mm socket 3/4" wrench
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More informationShotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationSlingshot Rotrex Supercharger Kit
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
More informationInstallation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L
Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2004.5-2007 Dodge 5.9L Figure 1 - Full Kit Photo 25 Figure 2 - Hardware Kit Please read all instructions before installation. This kit is not emissions
More informationC40008 & C40009 EXHAUST BRAKES
EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationMercedes E63/CLS AMG Carbon Turbo Intake System Instructions
Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions The goal of Alpha Performance is to provide the highest quality, best performing products available. By utilizing research and development,
More informationVEHICLE SPECIFIC ELECTRICAL INSTALLATION INSTRUCTIONS
WESTERN PRODUCTS, P.O. BOX 245038, MILWAUKEE, WI 53224-9538 Lit. No. 63723 VEHICLE SPECIFIC ELECTRICAL INSTALLATION INSTRUCTIONS FORD BRONCO F-150 4x4 F-250/350 4x4 and 2WD FORD SUPER DUTY 1980-1991 Model
More informationSpecial Note About The JDM High Performance Water Pump:
Page 1 of 30 JDM Engineering, Inc. home Call Us! 732-780- 0770 back to Installation Instructions Electric Fan Upgrade Kit Electric Fan Wiring Diagram Thank you for your purchase of the JDM Engineering
More informationACD-PRO Install in 2008 EvoX
Turning in a counter clockwise direction, unscrew ift knob ACD-PRO Install in 2008 EvoX Slide back and remove the floor console panel assembly Pull up to remove the center console tray Disconnect the plug
More informationFMK265SD F L DIESEL WITH DUAL ALTERNATORS
WITH DUAL ALTERNATORS This kit will NOT work on trucks equipped with adaptive steering. INSTALLATION NOTES 1. Disconnect negative batteries cables. Remove the air duct from the passenger side and the black
More informationWiper motor bolt and spacer. 3. Place relays as shown in picture so you can route the wires.
TSB Fan Relay Kit Please refer to a factory repair manual when working on your car. 1. Disconnect battery cables from the battery. 2. Remove bolt and spacer from wiper motor as shown in the picture. Wiper
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationShotgun Double Barrel HPFP install guide
Shotgun Double Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Double Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More information5481 FRONT ANTI-SWAY BAR 10+ CHEVROLET CAMARO
INSTALLATION INSTRUCTIONS 5481 FRONT ANTI-SWAY BAR 10+ CHEVROLET CAMARO CONGRATULATIONS! You were selective enough to choose a BELLTECH PRODUCT. We have spent many hours developing our line of products
More informationJeep Wrangler TJ 4.0 LITER Installation instructions
www.jeepair.com 2002-2004 Jeep Wrangler TJ 4.0 LITER Installation instructions Kit Information These directions are for 2002-2006 model Jeep Wranglers. After 1994 every vehicle was designed for R134a refrigerant.
More informationINSTALLATION INSTRUCTIONS 97 FORD EXPEDITION
INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before
More informationFRS/BRZ Air Oil Separator (AOS) Installation Manual
FRS/BRZ Air Oil Separator (AOS) Installation Manual Eric Hazen Rev. 2 Overview: Detailed instructions on installing the AOS for the FRS/BRZ/GT86. Difficulty: Beginner Time required: 1-3 hours depending
More informationZ1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 SETRAB
More informationAll cores due 30 days after invoice date - no credit after 60 days.
NO WARRANTY STATEMENT High performance parts & products no warranty policy: The purchaser understands and recognizes that high performance diesel products and services sold by INDUSTRIAL INJECTION SERVICE.
More information2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
More informationFitting Instructions: Sprint ST (955i), Sprint RS & Tiger 955cc Heated Grip Kit
Fitting Instructions: Sprint ST (955i), Sprint RS & Tiger 955cc Heated Grip Kit This accessory kit is designed for use on Triumph Sprint ST (955i), Sprint RS & Tiger 955cc motorcycles only and should not
More informationSECTION 1D2 M161 ENGINE COOLING
SECTION 1D2 M161 ENGINE COOLING CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More information750 Paso Wiring Upgrade
750 Paso Wiring Upgrade Supplies required: 2 Bosch 30A/12V Relays # #0 332 209 150 (with mounting tab) 1 30 Amp fuse holder 1 10 Amp fuse holder 12 inches of brown 12 gauge wire 60 inches of red 14 gauge
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+)
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+) Before You Start Please read instructions completely before installing. These
More informationTOYOTA TACOMA Part Number: TTA-BGB16-DRL TTA-BGP16-DRL
TOYOTA TACOMA 2016-17 Date: 10.29.2016 Billet Grille w/led DRL Part Number: TTA-BGB16-DRL TTA-BGP16-DRL Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Switch 4 1 User Card
More informationSingle Barrel Shotgun HPFP Install Guide
Single Barrel Shotgun HPFP Install Guide Thank you for purchasing the VTT Single Barrel Shotgun HPFP upgrade kit! PLEASE READ THE ENTIRE GUIDE BEFORE BEGINNING INSTALLATION! The first thing you should
More informationCooling system components, removing and installing
Page 1 of 40 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Versa Note 999F3 4Z000 - Accent Lighting Kit. 999Q9 AY000 - Accessory Service Connector
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit was designed for a standard single pump Radium Engineering
More informationZ1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 Aluminum
More informationSCION tc FOG LIGHT. Part Number: STC-312 / STC-812
SCION tc 2011-2013 FOG LIGHT Part Number: STC-312 / STC-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness
More informationJeep Wrangler TJ. Complete Air Conditioning System. Slide Control Head. Installation instructions
WWW.JEEPAIR.COM 1996-1998 Jeep Wrangler TJ Complete Air Conditioning System Slide Control Head Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The
More informationInstallation Instructions
Installation Instructions 2.0T FSI Intake Manifold: Featuring better flow, higher boost capacity, 40% larger plenum volume, and integrated flapper delete; this product will take your 2.0L VW TSI and FSI
More informationPart Number: TCO-314 / TCO-814
Date: 05.02.2014 TOYOTA COROLLA L, LE 2014-15 FOG LIGHT (Halogen and LED) Part Number: TCO-314 / TCO-814 Kit Contents Item # Quantity Reqd. Description 1 2 Light Housings 2 2 Fog Light bezels 3 1 Switch
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALL KIT Honda S2000 Document# 19-0063 Support: info@radiumauto.com WARNING: DO NOT SMOKE WHILE WORKING ON FUEL SYSTEMS. KEEP SPARKS AND OPEN FLAMES AWAY FROM
More informationJEEP WRANGLER (TJ), UNLIMITED (TJL), RUBICON MODELS BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT# KIT# 973
JEEP WRANGLER (TJ), UNLIMITED (TJL), RUBICON MODELS BODY LIFT KIT INSTALLATION INSTRUCTIONS 1997-2006 2 KIT# 972 3 KIT# 973 WARNING Installation of a Performance Automotive Group body lift will change
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1-19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT
More informationInstallation Manual. Model Chassis Code Engine Code Year
INTERCOOLER KIT NISSAN GT-R R35 (VR38 38DETT) SPEC-R HG TYPE29 Full KIT Installation Manual Please read the Installation Manual before installing. Keep this manual for future reference. Model Chassis Code
More informationTOYOTA PRIUS FOG LIGHT (Halogen or LED)
Part Number: TPR-413 / TPR-813 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Lower Grill 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware Bag Contents Item
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationTOYOTA COROLLA L, LE FOG LIGHT (Halogen and LED) Part Number: TCO-314 / TCO-814
TOYOTA COROLLA L, LE 2014-16 FOG LIGHT (Halogen and LED) Part Number: TCO-314 / TCO-814 Kit Contents Item # Quantity Reqd. Description 1 2 Light Housings 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit Before You Start Please read instructions completely before installing. These instructions contain the information required to install
More informationJEEP WRANGLER, RUBICON, UNLIMITED (TJ & TJL) 1 BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT# 951
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net JEEP WRANGLER, RUBICON, UNLIMITED (TJ & TJL) 1 BODY LIFT KIT INSTALLATION INSTRUCTIONS 1997-2006 KIT# 951 Installation of a Performance
More informationSUPERCHARGER. ON-VEHICLE INSPECTION 1. INSPECT SUPERCHARGER OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick.
EG45 ONVEHICLE INSPECTION 1. INSPECT OIL LEVEL HINT: With the engine cold, check the oil level on the dipstick. (a) Park the vehicle on a level spot and turn the engine off. (b) 4WD: Remove the LH front
More informationBuy products from authorized and licensed manufacturers using any of our patented processes, beware of cheap knock-offs, look for our licensing logo.
Part number SP2096 2008-10 Lexus IS-F 5.0L V8 1- Air intake system equipped with MR Tech and Air Fusion 1-5 Injen/AMSOIL (#1046) dry filter w/f1 styleinverted top 1-4 straight hose (#3129) 1-3 1/4 x 3
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Pathfinder 999F3 XZ000 - Accent Lighting Kit. Item QTY Description Service Part
More informationInstallation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with ECM controlled fan output)
Installation Instructions for Lingenfelter 2007-2013 GM 2500 Suburban & Yukon XL Auxiliary Fan System (with ECM controlled fan output) PN L300090607 Revision - 1.1 Lingenfelter Performance Engineering
More informationPart Number: TAV-713 TOYOTA AVALON LED DRL
Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad 6 1 Switch 7 2 Drill Jigs Hardware Bag Contents
More information30140 F5 Dual Fan Controller
30140 F5 Dual Fan Controller 1 2501 Ludelle Street Fort Worth, Texas 76105 817-244-6212 Phone 817-244-4024 Fax 888-350-6588 Sales 800-423-9696 Tech E-mail: painless@painlessperformance.com Web: www.painlessperformance.com
More informationPolaris Axys Sidekick Installation Instructions
2016-2017 Polaris Axys Sidekick Installation Instructions 1. Remove hood and side panels. 2. Remove fasteners and slide console back. 3. Remove belt and driven clutch. 4. Remove clutch cover/ oil-tank
More informationINSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT
INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM
More information18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines
8SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines KIT DESCRIPTION These service kits include all necessary parts to replace the low pressure fuel lines between the fuel filter housing and fuel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08E49-S2A-100 2004 S2000 AII 26325 Issue Date OCT 2003 PARTS LIST Hood switch harness TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver
More informationINSTALLATION INSTRUCTIONS
N-MT13-1 & N-MT13-2 COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS MUSTANG GT 2015-up PARTS INCLUDED Part Number Descrip on Qty 9-SA-INTAKE-100 Intake Assembly 1 9-SA-HEATSHIELD-100 Heatshield Assembly
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document 19-0009RevC FUEL SURGE TANK INSTALLATION KIT 2004+ LOTUS ELISE/EXIGE (2ZZ-GE) FRAME RAIL MOUNT Customer Service: info@radiumauto.com READ AND UNDERSTAND THESE INSTRUCTIONS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit wasn t designed for a FST-R, but can be accomplished. 1.
More informationCadillac CTS-V Power Steering Cooler Kit Model Year (6.2L LSA engine)
Cadillac CTS-V Power Steering Cooler Kit 2009-2015 Model Year (6.2L LSA engine) PN: L320050709 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761
More informationINSTALLATION INSTRUCTIONS SPULEN BILLET SPHERICAL CATCH CAN KIT - V2 VOLKSWAGEN: MK7 GOLF, GTI & GOLF R AUDI: 8V A3
INSTALLATION INSTRUCTIONS SPULEN BILLET SPHERICAL CATCH CAN KIT - V2 VOLKSWAGEN: MK7 GOLF, GTI & GOLF R AUDI: 8V A3 7675 & 7676 7499 & 7500 VIDEO INSTRUCTIONS ARE ALSO AVAILABLE ONLINE FOR A MORE ENHANCED
More informationInstallation Manual v2.2: Twin CP3 Fuel Injection Kit Dodge 5.9L
12/13/11 ATS Twin CP3 Kit 701-900-2272-INST Installation Manual v2.2: Twin CP3 Fuel Injection Kit 2003-2004 Dodge 5.9L Figure 1 - Full Kit Photo 26 Figure 2 - Hardware Kit 1 Please read all instructions
More informationEXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT
EXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT External Oil Filter with Coolant Filter Kit PACKING LIST: QTY. 4 4 Description Oil Filter Coolant Filter Small Brass 90 Fitting Large Brass 90 Fitting
More informationTOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation
TOYOTA FJ CRUISER 2007 AUXILIARY LIGHTS Preparation Part Number: PT297-35061 Kit Contents Item # Quantity Reqd. Description 1 2 Driving Lamp Assembly 2 1 Switch Harness 3 1 Lamp Harness 4 2 Stone Shield
More informationThis is the layout of a typical harness form a TPI Camaro.
TPI wiring harness, typical 1986-89: This is the layout of a typical harness form a 1986-88 TPI Camaro. (A) bulkhead conn. through firewall. (B) ecm conn. (C) jct. conn for fuel injectors and cooling fan.
More informationONBOARD AIR SYSTEM FOR ALL VEHICLES APPLICATIONS
ONBOARD SYSTEM FOR ALL VEHICLES APPLICATIONS Thank you and congratulations on the purchase of a Pacbrake onboard air system. Please read the manual prior to starting to ensure you can complete the installation
More informationJeep Wrangler TJ 4.0 LITER Installation instructions
www.jeepair.com 2000-2001 Jeep Wrangler TJ 4.0 LITER Installation instructions Important information about your system, and warranty DO NOT ADD ANY OIL TO ANY PART OF THE SYSTEM. DO NOT USE THE SIGHT GLASS
More informationINSTALLATION INSTRUCTIONS CATCH CAN KIT
INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN
More informationHARNESS KIT 3-PORT ISOLATION MODULE LIGHT SYSTEM
October 1, 2018 Lit. No. 92988, Rev. 00 72199 HARNESS KIT 3-PORT ISOLATION MODULE LIGHT SYSTEM Parts List and Installation Instructions Read this document before installing the harness kit. See your sales
More informationJeep Wrangler 4.0 Liter TJ Jeep Wrangler 2.5 Liter TJ Installation instructions
TM www.jeepair.com 1999 Jeep Wrangler 4.0 Liter TJ 1999-2001 Jeep Wrangler 2.5 Liter TJ Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The Jeep kit
More informationIn This DIY We Will Show You How To Install Recon Backup Lamps (part # To Run On A Separate Switch & In Reverse.
In This DIY We Will Show You How To Install Recon Backup Lamps (part # 264150 To Run On A Separate Switch & In Reverse. Please Note, There Are Many Ways of Installing These Lights, Including Wiring Methods,
More informationIE MK5/MK6 2.0T FSI & TSI FDS INTERCOOLER INSTALL GUIDE PART NUMBER: IETPCB1
IE MK5/MK6 2.0T FSI & TSI FDS INTERCOOLER INSTALL GUIDE PART NUMBER: IETPCB1 Thank you for purchasing another high quality Integrated Engineering product! This instruction sheet is used for installation
More information