Telescope spindle axis SA-3 / SA-6

Size: px
Start display at page:

Download "Telescope spindle axis SA-3 / SA-6"

Transcription

1 Telescope spindle axis SA-3 / SA-6 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the Original Montage Instructions Copyright by Afag Automation AG

2 These Montage Instructions apply to : Description: Type: Telecope spindle axis SA-3 / SA-6 Version of this documentation : Telescope spindle axis : SA-3-SA-6-OI-vers.3.0 gb Symbols : The actual serial number will be sticked in here upon delivery of the device. Assembly and initial start-up must be carried out by qualified Personnel only and according to these Montage Instructions. DANGER Indicates an immediate threatening danger. Non-compliance with this information can result in death or serious personal injuries (invalidity). WARNING Indicates a possible dangerous situation. Non-compliance with this information can result in death or serious personal injuries (invalidity). CAUTION Indicates a possibly dangerous situation. Non-compliance with this information can result in damage to property or light to medium personal injuries. NOTE Indicates general notes, useful operator tips and Installation recommendations which don t affect safety and health of the personnel. Seite 2 SA-3 - SA-6 - OI-vers.3.0 gb doc

3 Table of contents: Declaration of Incorporation Side Declaration of Incorporation according the Machinery Directive 2006/42/EG Side Module Information Side Transport and storage (packing and unpacking) Side Fastening the module Side Centering bushings Side Tightening torque for screw Side Slide unit load factors Side Description for the module Side Description module SA-3 / SA-6 Side Description motor arrangement Side Preferred combinations for SA-3 Side Preferred combinations for SA-6 Side Installation for SA spindle axis in a system Side Motor connection Side Interfaces of the telescope spindle axis Side Afag standard controller for spindle axis Side SE-24 Servo Controller Side SE-48 Servo Controller Side SE-Power for switch cuploard Side Product overview Servo Controller Side Programming the SA spindle extension Side Power failure during installation and set-up Side Noise emissions Side Protective device at the assembly system Side Montage Instructions Side Manufacturer address Side These operating instructions apply to Side General Description for SA-3 and SA-6 Side Supplied with the spindle axis SA telescope Side Warranty Side Dimensions SA-3 Side Technical data SA-3 Side 33 SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 3

4 3.1.7 Diagramme for SA-3 Side Dimensions SA-6 Side Technical data SA-6 Side Diagramme for SA-6 Side Installation Side First start-up Side Maintenance Instructions Side Maintenance and service the Telescope spindle axis Side Lubrication of the spindle drive Side Lubrication of the linear guide Side Further maintenance Side Accessories Side Trouble shooting Side Disassembling and repair Side Disposal Side 45 Seite 4 SA-3 - SA-6 - OI-vers.3.0 gb doc

5 1.0.0 EC Declaration for Incorporation (Document original) According to: 2006/42/EC Standard: EN ISO 12100:2010 (German Version) The manufacturer: Afag Automation AG, Fiechtenstrasse 32, CH-4950 Huttwil hereby declares that the incomplete machine: Producte name: Types: SA Telescope spindle axis (electrical) SA-3 / SA-6 Relevant EC Machinery Directive: EC Low Voltage Directive: 2006/95/EC EMC Directive: 2004/108/EC Norme machine: EN : 2006; EN 349 Standard: EN ISO 12100:2010 Safety of machinery General principles for risk assessment and risk reduction. The special technical documents shall be sent to a reasoned request by national authorities in printed documents or electronically (pdf). Applied and fulfilled essential requirements: 1.1; 1.1.1; 1.1.2; 1.2; 1.2.1; 1.2.3; ; 1.2.5; 1.3; 1.3.3; 1.3.5; 1.3.6; 1.3.7; ; ; 1.3.9; 1.4; 1.4.1; 1.5; 1.5.1; 1.6; 1.6.1; 1.6.3; 1.6.4; 1.7; 1.7.1; ; ; ; ; 3.3.5; Who installs this incomplete machine or assemble with other machines, a risk assessment for its resulting machine which must make the provisions of the EC directive: 2006/42 /EC Norme: EN ISO 12100:2010 Agent: For the compilation of the technically relevant documents: Niklaus Röthlisberger, Producte Manager Afag Automation AG, CH-4950 Huttwil Place/Date: Huttwil, Siegfried Egli Niklaus Röthlisberger Managing Director Afag Automation AG Producte Manager HT Afag Automation AG SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 5

6 2.0.0 Module Information Transport and storage (packing and unpacking) CAUTION Caution when to packing and unpacking the telescope spindleaxis! When careless handling of the telescope spindle axis fingers can be pinced as the axis in the state back and forth can be moved! The transport takes place in the transport packaging of Afag Automation AG. If there is no packaging of Afag Automation AG are used, they must be the telescope spindle axis shock and dust packed. The axis is in the transport package dry storage.. Telescope spindle axis can independently exit NOTE Depending on the type of SA telescope spindle axis can weight between 2.1 to 6.3 kg. The telescope spindle axis is a fine mechanical unit and must be handled with the necessary care and cleanliness during transport and storage as well as when handling, setting up and assembling. NOTE Consider please! With each module security is settled a technical newspaper. This newspaper is to be reas busily by each person with the module. Seite 6 SA-3 - SA-6 - OI-vers.3.0 gb doc

7 2.1.1 Fastening the module The module may only be fastened on its underside! SA-3: Hole matrix 30x30 mm / thread M4 / centering bushing Ø 7x3 mm SA-6: Hole matrix 48x48 mm / thread M6 / centering bushing Ø 9x4 mm The threads (M4) on the left and right side of the base body are only used for fastening additional parts (energy chain holder, switch fixtures etc.). When the screw length is determined, please note that the thread engagement of 7 mm (for the SA-3) or 12 mm (for the SA-6) is not exceeded! When the screw length is determined, please note that the thread engagement of 7 mm (for the SA-3) or 12 mm (for the SA-6) is not exceeded! Thread: SA-3 (M4) see design SA-6 (M6) see design SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 7

8 2.1.2 Centering bushings SA-3 Module Braket Hole spacing 30x30mm 30x30mm Thread M4 M4 Centering bushings (H7) Ø 7mm Ø 7mm SA-6 Module Braket Hole spacing 48x48mm 30x30mm Thread M6 M4 Centering bushings (H7) Ø 9mm Ø 7mm Use it for positioning the centering bushings supplied. Put them in two diagonally opposite mounting holes of the grid. Seite 8 SA-3 - SA-6 - OI-vers.3.0 gb doc

9 2.1.3 Tigthening torque for screws The screws to be used for assembly must at least satisfy the following conditions: Standard: VDI 2230 Strength: Classe 8.8 Surface: galvanized blue, oiled or greased Thread M3 M4 M5 M6 M8 Torque 1,1 1,4 Nm 2,6 3,3 Nm 5,2 6,5 Nm 9, ,3 Nm 21,6 27,3 Nm Tis is an incomplete machine Assembly of the telescope spindle axis in a system. The series SA of the telescope spindle axis modules is used for the linear, smooth movement of rigidly mounted loads under the ambient and Installation conditions defined for this Modul, see Technical data. The Installation position of the telescope spindle axis is arbitrary. NOTE These Montage Instructions should be read carefully before carrying out any activity on or with the telescope spindle axis module. The telescope spindle axis module may only be deployed in accordance with the intended use. Safety Instructions Modifications on the module that are not described in these Montage Instructions or have not been approved in writing by Afag automation are not permitted. In case of inexpert changes or improper assembly, installation, operation, maintenance or repairs, Afag rejects all liability. SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 9

10 2.1.4 Slide unit load factors SA-3 SA-6 Seite 10 SA-3 - SA-6 - OI-vers.3.0 gb doc

11 2.1.5 Description for the module The following types of the xx module (SA-3 and SA-6) are available: Type SA-3 SA-3 SA-6 SA-6 SA-6 Nominal stroke 50 mm 100 mm 100 mm 200 mm 300 mm Motor attachment optionally on the front left or right side or on the rear axial side.. The modules of the SA-series are modules with a movable bracket. Compared with the usual slide model this type series offers the advantage to dip into the working area and to leave it again completely. The bracket (2) is moved along a linear guide (3) vis-à-vis the base body (1). A ball-type linear drive (4) with a spindle nut mounted on the bracket (2) transforms the rotary movement in a linear movement. The spindle is driven by a servomotor (7) via a toothed belt back gear (5) or a torsionally stiff coupling (6). The reference switch (10) is an inductive sensor which recognizes the home position of the bracket during the reference run. The servomotor (7) can also be equipped with an integrated parking brake (8) which secures the bracket position when the module is not energized. This parking brake is required by all means in case of vertical applications! SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 11

12 2.1.6 Description 1 Base body 6 Coupling housing 2 Bracket 7 Servomotor 3 Linear guide 8 Integrated parking brake 4 5 Ball-type linear drive Toothed belt housing 9 10 Motor/Encoder connector Reference switch connector Seite 12 SA-3 - SA-6 - OI-vers.3.0 gb doc

13 2.1.7 Description / motor arrangement Switch off the controller of the module! - Remove cable - Remove cover (1) by unscrewing the screw (2) M3x6 mm. - Remove 4 screws (3) M4x16 mm (with the SA-3). - Remove 4 screws (3) M5x16 mm (with the SA-6). - Turn housing (4) by 90 to the left or right. - Tighten 4 screws (3) M4x16 mm with 4 Nm (in case of the SA-3). - Tighten 4 screws (3) M5x16 mm with 6 Nm (in case of the SA-6). - Screw down cover (1). - Cable mount - Switch on control system CAUTION Carry out a reference run with the module afterwards! (see controller manual) The correct toothed belt tension is retained and must NOT be changed! SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 13

14 2.1.8 Preferred combinations SA-3 Seite 14 SA-3 - SA-6 - OI-vers.3.0 gb doc

15 2.1.9 Prefered combinations SA-6 SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 15

16 NOTE For the cultivation of external modules to the telescope spindle axis over the Afag no liability. Any module are growing so big that they choose for a full telescope spindle axis of the stand and the payload does not exceed Installation for SA-spindle axis in a system CAUTION Installation of the SA-spindle axis in a system may occur only with switched off and secure control. The Installation of the SAspindle axis may be explained only by a certified professional person. The Installation of the SA-spindle axis may be explained only by a certified professional person. NOTE The investment farmer is himself responsible for the Installation spindle axis in a system. Seite 16 SA-3 - SA-6 - OI-vers.3.0 gb doc

17 2.2.1 Motor connection Interfaces of the telescope spindle axis SA-3 / SA-6 Pin assignment, motor connection: Connection: (View of motor side) Pin assignment, Encoder (View of encoder) SA-3 SA-6 Signal A 1 U B 5 V C 2 W D 3 GND Motor + 6 Brake Brake - Pin SA-3+ SA-6 Signal 1 S1 2 S3 3 S4 4 S2 5 R1 6 R2 7 Thermal switch 8 Thermal switch Pin assignment, reference nzw. Not-Stop-switch: Pin Signal V DC 3 GND 4 Signal, PNP NOTE We encourage you to use the standard cable Afag which are listed in the accessories. Motors plugs can be rotated Screws solve - Turn the plug - Tighten the screws SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 17

18 2.2.3 Afag standard controller for spindle axis HINWEIS The Afag offers to spindle axis two different controls. You take further information in the technical products catalogue. Seite 18 SA-3 - SA-6 - OI-vers.3.0 gb doc

19 Operator software SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 19

20 2.2.4 SE-24 Servo controller Seite 20 SA-3 - SA-6 - OI-vers.3.0 gb doc

21 2.2.5 SE-48 Controller SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 21

22 2.2.6 SE-Power for switch cupboard montage Seite 22 SA-3 - SA-6 - OI-vers.3.0 gb doc

23 2.2.7 Product overview servo controller NOTE Other Controls Informations take them in the technical product from catalogue (capter controls). SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 23

24 2.2.8 Programming the SA spindle extension CAUTION Caution: The SA spindle extensions should be started up in setup or jog mode. A wrong programming may trigger uncontrolled movements of the SA spindle extensions. Fast or unintentional movements of the module can result in personal injury and damage to property. The programming depends on the control system used. Observe the respective manuals of the control system supplier. If the Afag SE-Power control system is used, please observe the Montage Instructions which are added to the control system. The Montage Instructions can also be downloaded from the Afag homepage NOTE If wrong basic data is input at the PLC the SA spindle extension may move unhindered against the stopper leading to injury to persons by parts flying around. In case of a failure of the displacement encoder or a defective limit switch cable the SA spindle extension may execute unexpected movements. Persons working on the system may be injured. CAUTION It is the responsibility of the system manufacturer to ensure that the system is protected with a protective device so that persons are not injured during operation. Seite 24 SA-3 - SA-6 - OI-vers.3.0 gb doc

25 2.2.9 Power failure during installation and set-up NOTE In case of a power failure the SA spindle extension may glide downward without being braked by the motor so that persons working on the system get injured. CAUTION The person working on the system should therefore never stay under the SA spindle extension. It is the responsibility of the operator to ensure that these measures are observed. Misoperation of the system NOTE During set-up work the SA spindle extension may start due to wrong operation and cause injuries to persons working on the system. CAUTION It is the responsibility of the system manufacturer that persons perform their work properly when adjusting the SA spindle extension so that an uncontrolled start-up of the axis is prevented. Grounding: connection (isolation test in the production process) NOTE The SA spindle extension is to be grounded when it is installed in a system. Carry out an isolation test before start-up. Is it the responsibility of the owner to ensure the safety of the control system which controls the SA spindle extension responsible, SA boom since the spindle is controlled by him. SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 25

26 2.3.0 Noise emissions NOTE The SA spindle extension generates 65 db(a) during full-load operation. Depending on the add-ons, the environment and the resonance of the protective device these values may be exceeded and result in a disturbing higher noise level. CAUTION It is the responsibility of the system manufacturer to ensure that the permitted noise limit values are complied with. Otherwise an ear protection must be worn if necessary Protective device at the assembly system NOTE If an SA spindle extension is mounted in an assembly system the assembly system must be provided with a protective device. Warning: CAUTION Hot surfaces at the motor in continuous operation! Warning: Hot surfaces! Seite 26 SA-3 - SA-6 - OI-vers.3.0 gb doc

27 3.0.0 Montage Instructions Manufacturer address: Afag Automation AG Fiechtenstrasse 32 CH-4950 Huttwil Sales Handling: Tel (0) These instructions are valid for Monday: Producte name: Télescope spindle axis (electrical) Types: SA-3-50 SA SA SA SA SA Sequential series: No. 50xxxxxx This is an incomplete machine Who installs this incomplete machine or assemble with other machines, a risk assessment for its resulting machine which must make the provisions of the EC directive: 2006/42/EC Standard: EN ISO 12100:2010 (German version) Agent: For the compilation of the technically relevant documents: Niklaus Röthlisberger, Products Manager Afag Automation AG, CH-4950 Huttwil SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 27

28 3.1.1 These Montage Instructions apply to: Typ: SA-Telescope spindle axis: The actual serial number will be sticked in here upon delivery of the device. Version of this documentation: SA 3-SA 6-OI-vers.3.0 gb Symbols: Assembly and commissioning must be carried out by qualified personnel only ans according to these Montage Instructions. CAUTION For a potentially dangerous situation, the light body injuries could result. This signal word can also be used for warnings of damage to property may be used. NOTE For potentially harmful situation, where the product or object in its environment may be damaged. WARNING Indicates a possible dangerous situation. Non-compliance with this information can result in death or serious personal injuries (invalidity). Seite 28 SA-3 - SA-6 - OI-vers.3.0 gb doc

29 3.1.2 General Description for the SA-3 and SA-6 This is an incomplete machine The series of telescope spindle for the telescope spindle axis is arbitrary axis is used for shock-free linear movement of fixed loads in non-hazardous, and in the corridor defined for ambient and operating conditions, see technical data in the current catalog. The mounting position for the telescope spindle axis is arbitrary. Safety note NOTE Before any work at with the telescope spindle axis, this Montage Instructions carefully to read. The telescope spindle axis may be used according to the purpose. Modifications on the module that are not described in these Montage Instructions or have not been approved in writing by Afag are not permitted. In case of inexpert changes or improper assembly, installation, operation, maintenance or repairs, Afag rejects all liability. NOTE The Installation of a telescope spindle axis in a system that needs to be protected by one. This could careless people injured.. SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 29

30 3.1.3 Supplied with the spindle axis SA telescope The delivery depends on the order of the telescope spindle axis which is appointed by the order key in the technical catalog or on the WEB. Includes in the delivery: The best centering bushings and special screw. Transmission and engine have to be ordered after the order code. 1 Base body 6 Coupling housing 2 Bracket 7 Servomotor 3 Linear guide 8 Integrated parking brake 4 Ball-type linear drive 9 Motor/Encoder connector 5 Toothed belt housing 10 Reference switch connector Seite 30 SA-3 - SA-6 - OI-vers.3.0 gb doc

31 3.1.4 Warranty The module is designed for 40 million/2 years* load alterations under the ambient conditions and conditions of deployment defined for this module, see the Technical catalog. Wearing parts (e.g. toothed belts, spindle gears, linear guides) are excluded from this warranty. The warranty includes the repairs or replacement of faulty parts at Afag automation AG. *first go in event Carrying out repairs on the linear guide and the spindle gear without previous instruction by Afag automation AG nullifies the warranty. Any additional claims are excluded. SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 31

32 3.1.5 Dimension for SA-3 Seite 32 SA-3 - SA-6 - OI-vers.3.0 gb doc

33 3.1.6 Technical data SA-3 SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 33

34 3.1.7 Diagramme SA-3 Seite 34 SA-3 - SA-6 - OI-vers.3.0 gb doc

35 3.1.8 Dimension for SA-6 SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 35

36 3.1.9 Technical data SA-6 Seite 36 SA-3 - SA-6 - OI-vers.3.0 gb doc

37 3.2.0 Diagramme SA-6 SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 37

38 3.2.1 Installation CAUTION The SA-3 (SA-6) may execute unpredictable movements when the controller is switched on which can cause personal injuries or damage to the system. Make sure that the control system is switched off and secured against being switched on again when working on the module. Disconnect or connect cables only when the control system is switched off First start-up CAUTION Fast or unintentional movements of the module can result in personal injury and damage to the unit. Make sure that there are no persons or tools within the operative range of the module. Switch off the control system. Connect the encoder cable. Connect the motor cable. Switch on the control system and check the function of the position sensing system and the reference switch. Carry out a test run - first of all at slow traverse speed, - afterwards under operating conditions. Programming The programming depends on the control system used. Observe the respective manuals... Seite 38 SA-3 - SA-6 - OI-vers.3.0 gb doc

39 4.0.0 Maintenance instructions Maintenance and service the telescope spindle axis CAUTION With switched control of the SA-1 can run extra movement and cause injury or property damage. Make sure that the control system is switched off and secured against being switched on again when working on the axis. Maintenance interval Services measures As required Clean the module with a dry, lint-free cloth. The module must not be washed down; do not use any aggressive cleaners. 1 Montly Check the safety labels for damage, readability and cleanliness. Every 4 million load alternations Every 10 million load alternations Lubrication of the spindle drive Recommended grease: Klüber Microlube GBU-Y-131 Optional grease: type KP-1, N (DIN 51502) type NLGI-class 1 (DIN 51818) Lubrication of the linear guide Recommended grease: Klüber STABRAGS NBU 8 EP Optional: Type KP2K NLGI-classe 2 (DIN51818) CAUTION Lubricants with additives such as MoS 2, graphite or PTFE may not be used to service the linear guide. SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 39

40 4.1.1 Lubrication of the spindle drive 1 Blind plug 2 Lubrication nipple The spindle gear must be lubricated every 6 million load alternations (strokes). Move axis to the reference position Switch off the control system of the module CAUTION Switch off the control system of the module and secure it against being switched on again unintentionally. The signals of the control system may cause unintentional movements of the module which may lead to personal injuries. Remove the blind plug (1) out of the spindle cover. Regrease the spindle with a grease gun. We recommend to use Klüber Microlube GBU-Y-131 grease. Fit the blind plug. NOTE Instead of the grease mentioned above you may also use a grease of type Typ KP-1, N (DIN 51502) / Typ NLGI-classe 1 (DIN 51818). In order to spread the lubricant evenly 2 3 strokes should be executed at low speed when greasing is completed. Seite 40 SA-3 - SA-6 - OI-vers.3.0 gb doc

41 4.1.2 Lubrication of the linear guide The linear guide is lubricated with a special long-term grease when shipped. The linear guide must be relubricated every 10 million load alternations (strokes). - Move the axis to the front end position (= max. stroke). - Switch off the control system. - Remove grease residues or dirt from the guide rail. - Grease the tracks of the linear guide (1) in such a way that an even lubricating film is achieved. - Grease the guide carriage with a grease gun ( g). We recommend to use Klüber STABURAG S NBU 8P grease. In order to spread the lubricant evenly 2 3 strokes should be executed at low speed when greasing is completed. 1 Linear guide tracks 2 Lubricating hole of guide carriage NOTE Module inserts for ionized air environments (e.g. in case of highvoltage procedure such has corona processes). Open guides and pistons should be covered with a grease layer to avoid any rust. Afag standard: - Staburax NBU8EP (lat guides) - Blasolube 301 ( piston rods) SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 41

42 4.1.3 Further maintenance Under the ambient conditions mentioned below the linear module does not require any further maintenance: clean workshop atmosphere no splash water no dust and fumes caused by abrasion or processes ambient conditions according to the technical catalogue Security sticker At the following places are right security sticker. If they control regularly that security sticker exist and well readable! Accessories Article Order No. Proximity switch cable R1-5m-0-open see catalog technical Proximity switch cable R1-5m-90-open Proximity switch cable R2-3m-0-0 (SE-48) Proximity switch cable R2-5m-0-0 (SE-48) Proximity switch cable R2-3m-90-0 (SE-48) Proximity switch cable R2-5m-90-0 (SE-48) Encoder cable G5-5m-0-0 (SE-Power) Encoder cable G6-5m-0-0 (SE-Power) Encoder cable G8-3m-0-0 (SE-48) Encoder cable G8-5m-0-0 (SE-48) Encoder cable G9-3m-0-0 (SE-48) Encoder cable G9-5m-0-0 (SE-48) Motor cable M5-5m-0-open (SE-Power) Motor cable M9-3m-0-0 (SE-48) Motor cable M9-5m-0-0 (SE-48) Motor cable M10-5m-0-open Programming cable (SE-48) Programming cable (SE-Power) Power cable (SE-48) 5m I/O cable (SE-48) 5m Centering bushings Ø 7x Centering bushings Ø 9x MSDN für Fett Klüber Microlube GBU-Y-131 on request Angle plates VW Connections plates VP 154 ( SA-6 / PDZ-128) Seite 42 SA-3 - SA-6 - OI-vers.3.0 gb doc

43 4.1.5 Trouble- shooting CAUTION If the movable part of the module is oscillating heavily after the control system has been switched on (strong vibrations at the drive), switch off the module immediately, since otherwise the unit and the subsystems attached may get damaged. Faulte during the reference run Fault Possible cause Fault clearance Slide oscillates (very strong vibrations at the drive) Slide moves to the retracted limit position and stops Slide moves to the extended limit position and stops Wrong setting of control parameters Wrong connection of limit sensor Limit sensor connection interrupted Limit sensor defective Wrong direction of reference run Reset parameters at the control system Check pin assignment and correct, if necessary Check sensor cable Dans ce cas, le module revient au producteur! Check direction of reference run and change, if necessary Slide does not move Wrong connection of drive Check pin assignment and correct, if necessary Motor connection interrupted Drive defective Carry out functional test according to chapter "First start-up Check motor cable Have the drive replaced by Afag automation AG SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 43

44 Faults during operation Fault Possible cause Fault clearance Slide oscillates (very strong vibrations at the drive) Slide stops after a short stroke Toothed belt whistles Spindle whistles excessively Abnormal running noise at the module Wrong setting of control parameters Important contouring error Resolver connection interrupted Reset parameters at the control system Reduce values for acceleration and speed Check whether slide is stalled mechanically Check encoder cable Check encoder for proper functioning. See chapter " First start-up Wrong toothed belt tension Check toothed belt tension and retension according to the repair instructions Toothed belt defective Lubrication of spindle not okay End play in the spindle gear Appreciable play in the slide guide Replace defective toothed belt according to the repair instructions Lubricate spindle Have the spindle gear replaced by Afag AG Have guide replaced by Afag AG Seite 44 SA-3 - SA-6 - OI-vers.3.0 gb doc

45 4.1.6 Disassembly and repair When the module is damaged it can be returned to Afag AG for repair. CAUTION The module may only be disassembled when the system is aerated and deactivated. If pneumatic connections are disconnected when they are under pressure, this may result in serious personal injury due to fast movements of moving parts. When can the modules be repaired by the customer? Wearing parts can be exchanged by the customer itself when the warranty has expired. When the customer detects that the respective module is still under warranty: - he returns the module to company Afag AG for repair. - If the warranty has already expired, the customer must decide whether he repairs the module by himself and orders the wearing parts kit or whether he returns the module to company Afag Automation AG for repair. NOTE Afag offers a reliable repair service. Please note that Afag does not warranty for parts which were not repaired by Afag Automation AG Disposal NOTE SA telescope spindle axis which are of no further use should not be disposed of as a complete unit but dismantled into individual parts according to the type of material and recycled should be correctly disposed of. SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 45

46

47 SA-3 - SA-6 - OI-vers.3.0 gb doc Seite 47

48 Afag Automation AG Fiechtenstrasse 32 CH Huttwil Schwitzerland Tel.: Fax.: Internet: sales@afag.com

Telescope spindle axis SA-1

Telescope spindle axis SA-1 Telescope spindle axis SA-1 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the Original Montage Instructions Copyright by Afag Automation

More information

Universal Gripper UG 20, UG 25

Universal Gripper UG 20, UG 25 Universal Gripper UG 20, UG 25 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the Original Montage Instructions copyright by Afag Automation

More information

Rotary module CR 25 I CR 32. Declaration of Incorporation Module Information Montage Instructions Maintenance Instructions

Rotary module CR 25 I CR 32. Declaration of Incorporation Module Information Montage Instructions Maintenance Instructions Rotary module CR 25 I CR 32 Declaration of Incorporation Module Information Montage Instructions Maintenance Instructions Translation of the Original Montage Instructions Copyright by Afag Automation AG

More information

Rotary Module RM 25 und RM 32

Rotary Module RM 25 und RM 32 Rotary Module RM 25 und RM 32 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the Original Montage Instructions Copyright by Afag Automation

More information

- Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions

- Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Compact Slide CS 8 / CS 12 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the Original Montage Instructions Copyright by Afag Automation

More information

Gripper Module GMK 32 / GMQ 32. Rotary Gripper Module

Gripper Module GMK 32 / GMQ 32. Rotary Gripper Module Gripper Module GMK 32 / GMQ 32 Rotary Gripper Module GMQ 32/RM 16; GMQ 32/RM 25 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the

More information

Rotary modules CR 12 / CR 16 / CR 20

Rotary modules CR 12 / CR 16 / CR 20 Rotary modules CR 12 / CR 16 / CR 20 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the Original Montage Instructions Copyright by

More information

Gripper Module GMK 20 / GMQ 20 Rotary Gripper Modules GMQ 20-RM 16/GMQ 20-RM 25

Gripper Module GMK 20 / GMQ 20 Rotary Gripper Modules GMQ 20-RM 16/GMQ 20-RM 25 Gripper Module GMK 20 / GMQ 20 Rotary Gripper Modules GMQ 20-RM 16/GMQ 20-RM 25 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the

More information

Linear modules LM 20 and LM 25

Linear modules LM 20 and LM 25 Linear modules LM 20 and LM 25 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the Original Montage Instructions Copyright by Afag Automation

More information

Gripper Modules GMQ 12

Gripper Modules GMQ 12 Gripper Modules GMQ 12 Rotary gripper modules GMQ 12-RM 12 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the Original Montage Instructions

More information

Linear modules LM 32

Linear modules LM 32 Linear modules LM 32 - Declaration of Incorporation - Module Information - Montage Instructions - Maintenance Instructions Translation of the Original Montage Instructions Copyright by Afag Automation

More information

Gripper-rotations module GM 20 - RM 16 GM 20 - RM 25. Operating instructions....automatisch gut!

Gripper-rotations module GM 20 - RM 16 GM 20 - RM 25. Operating instructions....automatisch gut! Gripper-rotations module GM 20 - RM 16 GM 20 - RM 25 Operating instructions...automatisch gut! These operating instructions apply to: Type GM 20 Type RM 16 / RM 25 GMK 20/P RM 16 GMK 20/2 GMK 20/K GMK

More information

Gripper-rotary module GM 32 - RM 16 GM 32 - RM 25. Operating instructions....automatisch gut!

Gripper-rotary module GM 32 - RM 16 GM 32 - RM 25. Operating instructions....automatisch gut! Gripper-rotary module GM 32 - RM 16 GM 32 - RM 25 Operating instructions...automatisch gut! These operating instructions apply to: Type GM 20 Type RM 16 / RM 25 GMK 32/P RM 16 GMK 32/2 GMK 32/K GMK 32/3

More information

Compensation unit AGE-XY 50-80

Compensation unit AGE-XY 50-80 Translation of the origninal manual Compensation unit AGE-XY 50-80 Assembly and operating manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property of

More information

Bowl Feeder BF10 / BF15 Translation of original operating instruction

Bowl Feeder BF10 / BF15 Translation of original operating instruction Bowl Feeder BF10 / BF15 Translation of original operating instruction Copyright by Afag GmbH This operation instruction applies to: Bowl feeder right 12 Bowl feeder left 12 Type Order number BF10 BF15

More information

Bowl feeder WV401-1 / Translation of operating and installation instructions

Bowl feeder WV401-1 / Translation of operating and installation instructions Bowl feeder WV401-1 / 402-1 Translation of operating and installation instructions Copyright by Afag GmbH This operation instruction applies to: Bowl feeder WV401-1 Bowl feeder WV402-1 Type 230 V / 50

More information

Bowl Feeder BF10 / BF15 Translation of operating and installation instructions

Bowl Feeder BF10 / BF15 Translation of operating and installation instructions Bowl Feeder BF10 / BF15 Translation of operating and installation instructions Copyright by Afag GmbH This operation instruction applies to: Bowl feeder right 12 Bowl feeder left 12 Type Order number BF10

More information

Bowl feeder BF20 / BF25 / BF30 BF35 / BF40 / BF50

Bowl feeder BF20 / BF25 / BF30 BF35 / BF40 / BF50 Bowl feeder BF20 / BF25 / BF30 BF35 / BF40 / BF50 Translation of operating and installation instructions Copyright by Afag GmbH This operation instruction applies to: Type Order number BF20 BF25 BF30 BF35

More information

Bowl feeder BF20 / BF25 / BF30 BF35 / BF40 / BF50

Bowl feeder BF20 / BF25 / BF30 BF35 / BF40 / BF50 Bowl feeder BF20 / BF25 / BF30 BF35 / BF40 / BF50 Translation of original operating instruction Copyright by Afag GmbH This operation instruction applies to: Type Order number BF20 BF25 BF30 BF35 BF40

More information

Toothed belt axis ELGC-TB-KF. Operating instruction [ ]

Toothed belt axis ELGC-TB-KF. Operating instruction [ ] Toothed belt axis ELGC-TB-KF en Operating instruction 8068220 2017-02 [8068222] Original instructions Identification of hazards and instructions on how to prevent them: Danger Immediate dangers which can

More information

Swiveling gripper finger GFS 16-40

Swiveling gripper finger GFS 16-40 Translation of the original manual Swiveling gripper finger GFS 16-40 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property

More information

KeContact P20. User manual

KeContact P20. User manual KeContact P20 User manual Comments to this manual In this manual you will find warnings against possible dangerous situations. The used symbols apply to the following meanings:!! WARNING! Indicates a potentially

More information

Rotary feed-through DDF-S/-KS

Rotary feed-through DDF-S/-KS Translation of the Original Operating Manual Rotary feed-through DDF-S/-KS Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property

More information

Assembly and Maintenance Manual Type RSBW

Assembly and Maintenance Manual Type RSBW Assembly and Maintenance Manual Type RSBW Hatschekstr. 36 69126 Heidelberg Germany Tel +49(0)6221 30470 Tel +49(0)6221 304731 info@stieber.de www.stieber.de Stieber Clutch Date of issue: 16/03/2017 GB

More information

Mini slide EGSC-BS-KF. Operating instructions b [ ]

Mini slide EGSC-BS-KF. Operating instructions b [ ] Mini slide EGSC-BS-KF en Operating instructions 8081968 2017-11b [8081970] Translation of the original instructions EGSC-BS-KF-EN Identification of hazards and instructions on how to prevent them: Danger

More information

Linear unit, pneumatic KHM 40

Linear unit, pneumatic KHM 40 Translation of original operating manual Linear unit, pneumatic KHM 40 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property

More information

Small gripper with large stroke KGG

Small gripper with large stroke KGG Translation of the original manual Small gripper with large stroke KGG 220-280 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted

More information

2-finger parallel gripper GM

2-finger parallel gripper GM Translation of the Original operating manual 2-finger parallel gripper GM 80-201 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted

More information

Exchange of rollers from the XTS-Mover

Exchange of rollers from the XTS-Mover Service documentation for AT901-0050-0550 and AT9011-00x0-0550 Version: Date: 1.0 0.10.017 Table of contents Table of contents 1 Foreword... 5 1.1 Notes on the documentation... 5 1. Documentation issue

More information

Installation and Operating Instruction for Brake Caliper HW 150 HFA and HW 180 HFA E e

Installation and Operating Instruction for Brake Caliper HW 150 HFA and HW 180 HFA E e Installation and Operating Instruction for Brake Caliper HW 150 HFA and HW 180 HFA E 09.736e Schaberweg 30-38 Phone +49 6172 275-0 61348 Bad Homburg Fax +49 6172 275-275 Germany www.ringspann.com info@ringspann.com

More information

Operating and installation instructions

Operating and installation instructions DP30 DP32 DP33 DP34 Contents 1.0 General information on operating instructions... 2-2 2.0 Notes on possible dangers... 2-2 2.1 Significance of symbols... 2-2 2.2 Explanatory notes on safety information...

More information

Compact Linear Module CLM

Compact Linear Module CLM Translation of the original manual Compact Linear Module CLM Assembly and operating manual Superior Clamping and Gripping Translation of the original manual Imprint: Copyright: This manual remains the

More information

2-finger angular gripper PWG

2-finger angular gripper PWG Original operating manual 2-finger angular gripper PWG 65-230 Assembly and operating manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property of SCHUNK

More information

Planar surface gantry EXCM-30. Instructions. Mechanical installation b [ ]

Planar surface gantry EXCM-30. Instructions. Mechanical installation b [ ] Planar surface gantry EXCM-30 Instructions Mechanical installation 804447 605b [8044434] EXCM-30 Translation of the original instructions LOCTITE is a registered trademark of its respective trademark holder

More information

Technical Documentation

Technical Documentation Technical Documentation Product manual Holding brake controller Document: 0198441113316 Edition: V1.00, 03.2006 Important information The drive systems described here are products for general use that

More information

Operating and installation instructions

Operating and installation instructions Pneumatic actuators DP34 Tandem / DP34 Tridem DP34T Contents DP34Tri 1.0 General information on operating instructions...2-2 2.0 Notes on possible dangers...2-2 2.1 Significance of symbols...2-2 2.2 Explanatory

More information

HST -LS Interlocking device (Translation of Original Manual)

HST -LS Interlocking device (Translation of Original Manual) Installation and Operating Manual for Components HST -LS Interlocking device (Translation of Original Manual) HST-LS Ident.-No.: 10268 HST-LS Ident.-No.: 10269 HST-LS, pictured Ident-Nr. 10269 The image

More information

Spindle axis ELGC-BS-KF. Operating instructions [ ]

Spindle axis ELGC-BS-KF. Operating instructions [ ] Spindle axis ELGC-BS-KF en Operating instructions 8067243 2017-01 [8067245] Original instructions Identification of hazards and instructions on how to prevent them: Danger Immediate dangers which can lead

More information

Assembly and Maintenance Manual Type ASNU

Assembly and Maintenance Manual Type ASNU Assembly and Maintenance Manual Type ASNU Hatschekstr.36 69126 Heidelberg Germany Tel +49(0)6221 30470 Fax +49(0)6221 304731 info@stieber.de www.stieber.de Date of issue: 30.05.2018 GB Revision: 0 U:\EngUsers\!ProduktDoku\1AAA_Einbauerklaerung_Wartungsanleitung_Konformitaetserklaerung\1AAA_Wartungsanleitungen\Orginal_Worddatei\_ASNU.docx

More information

These operating instructions apply for: NCX 380 NCZ 300 NCX 480 NCZ 370 NCX 580 L NCZ 480 NCX 660 K NCZ 560 NCZ 660 NCZ 800

These operating instructions apply for: NCX 380 NCZ 300 NCX 480 NCZ 370 NCX 580 L NCZ 480 NCX 660 K NCZ 560 NCZ 660 NCZ 800 Original instructions Operating Instructions for May 2010 Electric Internal Vibrators BA No. 1092E Series NCX and NCZ These operating instructions apply for: NCX 380 NCZ 300 NCX 480 NCZ 370 NCX 580 L NCZ

More information

Angle seat valve with diaphragm actuator VZXA-...-M

Angle seat valve with diaphragm actuator VZXA-...-M Angle seat valve with diaphragm actuator VZXA-...-M Instructions Operating (Translation of the original instructions) Festo AG & Co. KG Ruiter Straße 82 73734 Esslingen Germany +49 711 347-0 www.festo.com

More information

Rotary feed-through DDF 2

Rotary feed-through DDF 2 Translation of the original operating manual Rotary feed-through DDF 2 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property

More information

Angle seat valve with piston actuator VZXA-...-K

Angle seat valve with piston actuator VZXA-...-K Angle seat valve with piston actuator VZXA-...-K Instructions Operating (Translation of the original instructions) Festo AG & Co. KG Ruiter Straße 82 73734 Esslingen Germany +49 711 347-0 www.festo.com

More information

Coaxial Joining (6-axis) FUS

Coaxial Joining (6-axis) FUS Original Manual Coaxial Joining (6-axis) FUS Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property of SCHUNK GmbH & Co. KG.

More information

Vibratory hopper unit NVD 3 / NVD 4 Translation of operating and installation instructions

Vibratory hopper unit NVD 3 / NVD 4 Translation of operating and installation instructions Vibratory hopper unit NVD 3 / NVD 4 Translation of operating and installation instructions Copyright by Afag GmbH This operation instruction applies to: NVD3/5 NVD4/10 NVD4/15 NVD4/20 NVD4/40 5,0 Liters

More information

CENTAFLEX-K Assembly and operating instructions 014K S... M EN Rev. 1

CENTAFLEX-K Assembly and operating instructions 014K S... M EN Rev. 1 Assembly and operating instructions Contents 1 General remarks... 5 2 Safety... 6 2.1 Qualification of deployed personnel... 6 2.2 Warning notes... 6 2.2.1 Signal words... 6 2.2.2 Symbols... 7 2.3 Application

More information

ELGC-BS-KF. Spindle axis. Instructions Operating c [ ]

ELGC-BS-KF. Spindle axis. Instructions Operating c [ ] ELGC-BS-KF Spindle axis Instructions Operating 8095590 8095590 2018-08c [8095592] Translation of the original instructions 2 Festo ELGC-BS-KF 2018-08c Table of contents 1 Further applicable documents...

More information

Swing Piston Compressors and Vacuum Pumps

Swing Piston Compressors and Vacuum Pumps Swing Piston Compressors and Vacuum Pumps NPK 018 AC Pressure NPK 018 DC Pressure NPK 018 AC Vacuum NPK 018 DC Vacuum Operating and Installation Instructions Read and observe these Operating and Installation

More information

Drive Unit e-drive1. Installation instructions 04/2014. English translation of the original German installation instructions

Drive Unit e-drive1. Installation instructions 04/2014. English translation of the original German installation instructions Drive Unit e-drive1 Installation instructions 04/2014 English translation of the original German installation instructions Contents Foreword... 3 Availability... 3 Structural features in the text... 3

More information

Installation and Operating Manual for Tank and Equipment Cleaning Nozzles Series 5TM

Installation and Operating Manual for Tank and Equipment Cleaning Nozzles Series 5TM Installation and Operating Manual for Tank and Equipment Cleaning Nozzles Series 5TM 150 150 150 This instruction manual contains proprietary information which is protected by copyright laws. No part of

More information

User manual Pipe notcher Type: AL 1-2E

User manual Pipe notcher Type: AL 1-2E User manual Pipe notcher Type: AL 1-2E Page 1 of 27 Table of contents 1. Foreword... 4 1.1. Name of machine... 4 1.2. Warning... 4 1.3. Target group for each chapter... 4 1.4. Symbols... 4 1.5. Re-ordering

More information

Technical Data Sheet TI-F55 Locking Units series KFHS (with DGUV approval)

Technical Data Sheet TI-F55 Locking Units series KFHS (with DGUV approval) English translation of German original Technical Data Sheet TI-F55 Locking Units series KFHS (with DGUV approval) For a detailed functional description refer to Technical Information TI-F10. Further important

More information

Linear gantry EXCT. Description. Mechanical installation NH [ ]

Linear gantry EXCT. Description. Mechanical installation NH [ ] Linear gantry EXCT Description Mechanical installation 8059080 60NH [805908] EXCT Translation of the original instructions EXCT-EN LOCTITE is a registered trademark of its respective trademark holder in

More information

Linear axis ELM 23-37

Linear axis ELM 23-37 Translation of the original manual Linear axis ELM 23-37 Assembly and operating manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property of SCHUNK GmbH

More information

User Guide. Lubricus Lubrication System LUB-D1/LUB-D2/LUB-D3/LUB-D4 (24 VDC)

User Guide. Lubricus Lubrication System LUB-D1/LUB-D2/LUB-D3/LUB-D4 (24 VDC) User Guide Lubricus Lubrication System LUB-D1/LUB-D2/LUB-D3/LUB-D4 (24 VDC) version 04/2013 Content General Information 3 Warning 3 Scope of Supply 3 Overview 3 General safety details 4 Intended use 4

More information

2-Finger-Parallel-Gripper PFH

2-Finger-Parallel-Gripper PFH Translation of the Original Manual 2-Finger-Parallel-Gripper PFH 150-300 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property

More information

Assembly and Maintenance Manual Type AS

Assembly and Maintenance Manual Type AS Assembly and Maintenance Manual Type AS Hatschekstr.36 69126 Heidelberg Germany Tel +49(0)6221 30470 Fax +49(0)6221 304731 info@stieber.de www.stieber.de Date of issue: 30.05.2018 GB Revision: 0 U:\EngUsers\!ProduktDoku\1AAA_Einbauerklaerung_Wartungsanleitung_Konformitaetserklaerung\1AAA_Wartungsanleitungen\Orginal_Worddatei\_AS.docx

More information

2-Finger-Angular Gripper LGW 10-40

2-Finger-Angular Gripper LGW 10-40 Translation of the orginial manual 2-Finger-Angular Gripper LGW 10-40 Assembly- and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property

More information

Linear feeder HLF07-M / 12-M / 25-M

Linear feeder HLF07-M / 12-M / 25-M Linear feeder HLF07-M / 12-M / 25-M Translation of operating and installation instructions Copyright by Afag GmbH This operation instruction applies to: Linear feeder Linear feeder Linear feeder Type HLF07

More information

INSTRUCTION MANUAL. I/P Converter DSG BXXY3Z DSG BXXY4Z

INSTRUCTION MANUAL. I/P Converter DSG BXXY3Z DSG BXXY4Z INSTRUCTION MANUAL I/P Converter DSG BXXY3Z DSG BXXY4Z Revision 2.0 3.626 016136 en Page 1/15 Should you have any questions concerning the I/P converter, please contact the Service Department of the Product

More information

Stacking gripper SG 47

Stacking gripper SG 47 Original operating manual Stacking gripper SG 47 Assembly and operating manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property of SCHUNK GmbH & Co.

More information

Assembly Instructions

Assembly Instructions Rev.. Assembly Instructions - Hand Spray Valve SMS-6 Page of 20 Assembly Instructions Hand Spray Valve SMS-6 Article Number: S6- NOTE Please read the Assembly Instructions carefully before first using

More information

Installation and Operating Instructions for EAS -NC clutch Type 45_. _. _ Sizes 02 and 03

Installation and Operating Instructions for EAS -NC clutch Type 45_. _. _ Sizes 02 and 03 Table of contents: Please read and observe this Operating Instruction carefully! A possible malfunction or failure of the clutch and any damage may be caused by not observing it. Page 1: - Table of contents

More information

standards based cylinder DNCI Operating instructions e [ ]

standards based cylinder DNCI Operating instructions e [ ] standards based cylinder DNCI en Operating instructions 8072823 2017-05e [8072825] Original instructions Identification of hazards and instructions on how to prevent them: Danger Immediate dangers which

More information

Original Operating Manual

Original Operating Manual 2010-10-29 Original Operating Manual Control Panel Comfort for Pedelecs Series 4313 Save for future use! Marquardt GmbH Schlossstraße 16 78604 Rietheim-Weilheim E-mail: marquardt@marquardt.de Website:

More information

Original Operating Manual

Original Operating Manual matev GmbH Nürnberger Str. 50 90579 Langenzenn T +49 (0) 9101 9087-0 F +49 (0) 9101 9087-20 info@matev.eu www.matev.eu Original Operating Manual Snow blade SRM-FB 120 CD Angle adjustment mechanical Version

More information

Service - Safety Manual

Service - Safety Manual Service - Safety Manual Mounting and maintenance instructions Linear Units LT50 series Code Unit Serial number Date by Linear Units LT50 series Table of contents 1 Safety 3 1.1 Significance of the manual

More information

Instructions for Fitting, Operating and Maintenance Canopy Door RE / (St.: )

Instructions for Fitting, Operating and Maintenance Canopy Door RE / (St.: ) EN Instructions for Fitting, Operating and Maintenance Canopy Door 1 818 012 RE / (St.: 12.2010) 12.2010 ENGLISH Contents 1 Safety Instructions... 3 1.1 Qualified persons... 3 1.2 Symbols and signal words

More information

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation Globe control valve, pneumatically operated Actuator sizes 40 mm - 125 mm, Nominal diameter DN10-65 Kolbengesteuertes Geradsitzventil Antriebsgrößen 40 mm - 125 mm, Nennweiten DN10-65 Vanne à siège droit

More information

Quick-Disconnect Coupling one-hand operation Push Pull ND 5, connecting thread G 1/4,max. operating pressure 500 bar

Quick-Disconnect Coupling one-hand operation Push Pull ND 5, connecting thread G 1/4,max. operating pressure 500 bar Issue 12-2013 Quick-Disconnect Coupling one-hand operation Push Pull ND 5, connecting thread G 1/4,max. operating pressure 500 bar Figure 1: Coupling complete Figure 4: Coded coupling, complete Table of

More information

Series Type ROi400 DE EN FR. Montage- und Betriebsanleitung Installation and operating instructions Instructions de montage et d utilisation

Series Type ROi400 DE EN FR. Montage- und Betriebsanleitung Installation and operating instructions Instructions de montage et d utilisation Montage- und Betriebsanleitung Installation and operating instructions Instructions de montage et d utilisation DE EN FR Member of JOST-World Modellreihe Series Type ROi400 Vollautomatische Anhängekupplung

More information

Collision and Overload Protection OPS

Collision and Overload Protection OPS Translation of the original manual Collision and Overload Protection OPS 80-300 Assembly and Operating manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted

More information

Turbocharger / VTR..0, VTR..1 Original assembly instructions English

Turbocharger / VTR..0, VTR..1 Original assembly instructions English Assembly Instructions Turbocharger / VTR..0, VTR..1 Original assembly instructions English This document is valid for the VTR..0/..1 series: VTR160, VTR200, VTR250, VTR320, VTR400 VTR161, VTR201, VTR251,

More information

CENTAX-TEST Assembly and operating instructions 053C GB3. M EN Rev. 1

CENTAX-TEST Assembly and operating instructions 053C GB3. M EN Rev. 1 Assembly and operating instructions Contents 1 General remarks... 5 2 Safety... 6 2.1 Safety remarks... 6 2.1.1 Signal words... 6 2.1.2 Pictograms... 7 2.2 Qualification of deployed personnel... 7 2.3

More information

Pneumatic rotary actuator SRH-plus 20-60

Pneumatic rotary actuator SRH-plus 20-60 Translation of the Original operating manual Pneumatic rotary actuator SRH-plus 20-60 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted

More information

FLENDER ZAPEX couplings. Type ZWT. Operating instructions BA 3505 EN 10/2011. FLENDER couplings

FLENDER ZAPEX couplings. Type ZWT. Operating instructions BA 3505 EN 10/2011. FLENDER couplings FLENDER ZAPEX couplings Type ZWT Operating instructions FLENDER couplings FLENDER ZAPEX couplings Type ZWT Operating instructions Translation of the original operating instructions Technical data Notes

More information

Pneumatic grease pump 50:1 and grease supply system

Pneumatic grease pump 50:1 and grease supply system Pneumatic grease pump 50:1 and grease supply system 03 591 A411 GB G Operating instructions for Pneumatic grease pump 50:1 Contents 1. General Information 2 1.1 Usage Stipulations 2 1.2 Construction &

More information

Air terminal devices

Air terminal devices Installation manual GB/en Air terminal devices Slot Diffusers Type PureLine18 TROX GmbH Heinrich-Trox-Platz 47504 Neukirchen-Vluyn Germany Phone: +49 (0) 2845 2020 Fax: +49 (0) 2845 202265 E-mail: trox@trox.de

More information

Printed: Doc-Nr: PUB / / 000 / 00

Printed: Doc-Nr: PUB / / 000 / 00 ORIGINAL OPERATING INSTRUCTIONS Hilti HTE-P 33 dispenser It is essential that the operating instructions are read before the tool is operated for the first time. Always keep these operating instructions

More information

Sealed Angle Gripper DWG 44-80

Sealed Angle Gripper DWG 44-80 Translation of the original manual Sealed Angle Gripper DWG 44-80 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property of

More information

Wind Power Inverter WINDY BOY 5000A/6000A

Wind Power Inverter WINDY BOY 5000A/6000A Wind Power Inverter WINDY BOY 5000A/6000A User Manual WB5A-6A-BA-BEN114530 TBEN-WB50-60A Version 3.0 EN SMA Solar Technology AG Table of Contents Table of Contents 1 Information on this Manual.........................

More information

Mounting and Operating Instructions EB EN. Type 3372 Electropneumatic Actuator. Actuator area: 120 and 350 cm² With Type 3725 Positioner

Mounting and Operating Instructions EB EN. Type 3372 Electropneumatic Actuator. Actuator area: 120 and 350 cm² With Type 3725 Positioner Type 3372 Electropneumatic Actuator Actuator area: 120 and 350 cm² With Type 3725 Positioner Translation of original instructions Type 3372 with 120 cm² actuator area Type 3372 with 350 cm² actuator area

More information

OTTO HYDRAULICS GmbH & Co KG SYSTEME UND KOMPONENTEN FÜR ÖLHYDRAULISCHE ANTRIEBE UND STEUERUNGEN SIEMENSSTRASSE 12/ FRIEDRICHSHAFEN

OTTO HYDRAULICS GmbH & Co KG SYSTEME UND KOMPONENTEN FÜR ÖLHYDRAULISCHE ANTRIEBE UND STEUERUNGEN SIEMENSSTRASSE 12/ FRIEDRICHSHAFEN Hydraulik-aggregates Otto-Hydraulics Operating manual Author: Reinhard Otto Date: 16.01.2016 Operating manual rev.1 page: 1/11 Table of Contents Page 1...General information of this operating manual 3

More information

Oil-free piston compressors KK and piston vacuum pumps KV

Oil-free piston compressors KK and piston vacuum pumps KV Oil-free piston compressors KK and piston vacuum pumps KV Installation and Operating Instructions 0678106030L02 1707V003 Contents Important information 1 About this document 2 1.1 Warnings and symbols

More information

Operating manual. Custom made gearboxes

Operating manual. Custom made gearboxes Operating manual Custom made gearboxes DSS-Nr. 100389549 DSS-Rev. 001 Datum 16.01.2018 Contents Contents 1 General information 3 1.1 Using the operating manual 3 1.2 Warnings in this operating manual 4

More information

FLENDER ARPEX Plate packs with close-fitting bolt connection. ARW-4 Sizes to Assembly instructions An 4239 en 12/2015.

FLENDER ARPEX Plate packs with close-fitting bolt connection. ARW-4 Sizes to Assembly instructions An 4239 en 12/2015. FLENDER ARPEX Plate packs with close-fitting bolt connection ARW-4 Sizes 101-4 to 292-4 Assembly instructions FLENDER couplings FLENDER ARPEX Plate packs with close-fitting bolt connection ARW-4 Sizes

More information

Rack and pinion axis EHMH. Operating instructions [ ]

Rack and pinion axis EHMH. Operating instructions [ ] Rack and pinion axis EHMH en Operating instructions 8076544 2017-09 [8076555] Translation of the original instructions GDCP-EHMH-EN Symbols used: Caution Hazards that can cause minor injuries Note Material

More information

Compensation unit AGE-F-XY 31-80

Compensation unit AGE-F-XY 31-80 Translation of the original manual Compensation unit AGE-F-XY 31-80 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property

More information

Safety Shock Absorbers SCS33 to SCS64

Safety Shock Absorbers SCS33 to SCS64 Safety Shock Absorbers SCS33 to SCS64 1 Operating Instruction SCS33-25EU SCS33-50EU SCS45-25EU SCS45-50EU SCS45-75EU Rod Button SCS64-50EU SCS64-100EU SCS64-150EU Integrated Rod Seals Main Bearing Content

More information

PN9000 Series Pneumatic Actuators Installation and Maintenance Instructions

PN9000 Series Pneumatic Actuators Installation and Maintenance Instructions 3579049/14 IM-P357-29 CTLS Issue 14 PN9000 Series Pneumatic Actuators Installation and Maintenance Instructions PN9100 PN9200 1. Safety information 2. General product information PN9300 3. Installation

More information

Angle seat valve with piston actuator VZXA-...-K

Angle seat valve with piston actuator VZXA-...-K Angle seat valve with piston actuator VZXA-...-K Festo AG & Co. KG Postfach 73726 Esslingen Germany +49 711 347-0 www.festo.com 3 Further information Accessories www.festo.com/catalogue Spare parts www.festo.com/spareparts

More information

Pneumatic Swivel Unit SRU 20-60

Pneumatic Swivel Unit SRU 20-60 Translation of the original manual Pneumatic Swivel Unit SRU 20-60 Assembly and operation manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property of

More information

Operating Instructions

Operating Instructions 16 1 Independent & Unauthorized Changes and Spare Parts Alterations and changes to actuators are only possible, i.e. permitted under express permission from the company airpower Europe GmbH. These conditions

More information

Stud Gun Automatic Stud Gun EP-8, EP-9, EP-10

Stud Gun Automatic Stud Gun EP-8, EP-9, EP-10 Stud Gun Automatic Operating instructions (ID-No. 00035102) 00100192 EP-8 (gun for manual use) 00101758 EP-8 (gun for machine) 00100193 EP-9 (gun for manual use) 00100262 EP-9 (gun for machine) assembled:

More information

Electric cylinder ESBF-BS/-LS Operating instructions b [ ]

Electric cylinder ESBF-BS/-LS Operating instructions b [ ] Electric cylinder ESBF-BS/-LS-32... 100 en Operating instructions 8076295 2017-11b [8079297] Translation of the original instructions Symbols: Warning Installation and commissioning may only be performed

More information

Pneumatic rotary actuator SRH-plus 20-60

Pneumatic rotary actuator SRH-plus 20-60 Translation of the Original operating manual Pneumatic rotary actuator SRH-plus 20-60 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted

More information

Storage, operating and maintenance instructions for AZ plug valves and Standard valves

Storage, operating and maintenance instructions for AZ plug valves and Standard valves ARMATUREN Plug - Valves metallic with PTFE Sleeve 2-7 way Storage, operating and maintenance instructions for AZ plug valves and Standard valves Plug - Valves FEP/PFA - lined, 2-3 way Butterfly - Valves

More information

Original Installation and Maintenance Instructions. Linear unit. Type Beta 165-C-SSF

Original Installation and Maintenance Instructions. Linear unit. Type Beta 165-C-SSF Original Installation and Maintenance Instructions Linear unit Type Beta 165-C-SSF FM 240 Master-MuW-Anleitung Beta-Typ-S Rev.01 HSB Automation GmbH In Laisen 74 D-72766 Reutlingen Germany Tel. +49 7121

More information

Instruction Manual. Ex-Time 40 / 50

Instruction Manual. Ex-Time 40 / 50 Instruction Manual Ex-Time 40 / 50 Contents 1. Introduction 13 2. Safety Advice 13 3. Faults and Damage 13-14 4. Safety Regulations 14 5. Ex-Data 14-15 6. Technical Data 15-16 7. Use and Application /

More information

2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE

2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE 2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE For Diaphragm Dosing Pumps FEM 1.02_.55 / FEM 1.09_.55 Controller board package, without pump: ID 160536 Operating and Installation Manual It is important to

More information