Part# CE-9800H & CE-9801H Jeep Wrangler TJ / LJ Lift Kit Installation Instructions

Size: px
Start display at page:

Download "Part# CE-9800H & CE-9801H Jeep Wrangler TJ / LJ Lift Kit Installation Instructions"

Transcription

1 Part# CE-9800H & CE-9801H Jeep Wrangler TJ / LJ Lift Kit Installation Instructions Please note that modifying the suspension of your Jeep Wrangler will affect the vehicle handling and stability characteristics! You have purchased a RockJock suspension lift system for Jeep Wrangler. This suspension system will provide ample lift to accommodate up to 35" tall tires.* A 4½ back spacing wheel was used for the development of this kit. Other wheel & tire configurations can be used but interference may be an issue. * For clearance it may be necessary to use a 1" body lift and/or different type of fender flares. Some body trimming may also be necessary depending upon application. 1

2 Kit includes: 1 pr. CE-9807FSP Front Coil Springs 1 pr. CE-9102 Front Upper Arms 1 pr. CE-9106 Front Lower Arms 1 CE-9122F Front Bump Stop Kit 1 pr. CE-9141 Front Sway Bar Disconnect 1 CE-9120TJS Front Adjustable Track Bar 1 pr. CE-9131RH Rear Coil Springs 1 CE-9121 Rear Track Bar Relocator 1 CE-9122R Rear Bump Stop Kit 1 pr. CE-9103 Rear Upper Control Arms 1 pr. CE-9106 Rear Lower Control Arms 1 pr. CE-9142 Rear Sway Bar Links Optional Equipment Shown/Available Front Antirock Kit, use Lift Kit # CE-9801H Front Antirock Sway Bar Kit CE-9900 Rear Shock Relocator Kit CE-9601 Rear Antirock Sway Bar Kit CE-9900TJR Set of 4 Rancho 9000 Shocks CE-9150 Front Shocks (Rancho ) CE-9151 Rear Shocks (Rancho ) CE-9152 Currectlync Heavy Duty Steering CE-9701 Short Tail Shaft Conversion (non Rubicon) CE-9069T 1" Body Lift CE-9300 HD Motor Mounts, 1" raised CE-9200 HD Steering Stabilizer CE-9170 Rear CV Drive Shaft TJ CE Rear CV Drive Shaft LJ CE-97984U Rear CV Drive Shaft TJ Rubicon CE-9069R Rear CV Drive Shaft LJ Rubicon CE-9069RU Johnny Joint Adjustable Rear Trac Bar CE-9120R Instructions Tools Needed Complete Set of Hand Tools Metric and SAE Drill 7/16" Drill Bit 7/16-14 Tap Grease Gun Angle Finder Jack Stands Floor Jack Red Loctite 1. Read the complete instruction manual before starting installation. 2. Park your vehicle on level ground and disconnect front and rear track bars from the axles. 3. Lift the vehicle on jack stands by the frame. Ensure vehicle stability before working on the vehicle. 4. Remove wheels and tires from the vehicle. 5. Use red Loctite on all suspension hardware when assembling. Front Installation 6. Remove the bolt that holds the brake line on the side of the frame and relocate by drilling two holes on the lower edge of the frame, 1.5" down from stock location. 2

3 7. Remove front drive shaft from the front axle. 8. Install front upper and lower control arms, one at a time. You must drill UPPER control arm holes in the frame and the housing out to 7/16". 9. Place a floor jack under the front axle and remove the front shocks. Place a set of jack stands under the front axle and slowly release the jack allowing the front axle to drop, releasing pressure from the springs. DO NOT OVER EXTEND THE BRAKE LINES!!!!!!! 10. Remove the front springs and factory track bar from the frame. 11. Drill to 3/8" and then tap the center of the lower spring pad to 7/16-14 thread. 12. Install the front upper bump stop.** ** Refer to the suplimental instruction sheet specific to this component. 3

4 13. Drill the frame side track bar mount hole to 5/8". 14. Install the front springs and lower bump stop.** ** Refer to the suplimental instruction sheet specific to this component. 4

5 15. With the floor jack, raise the front axle and install the front shocks. 16. Install the track bar on the frame side only.** 17. At this time you can install the front sway bar links or the front Antirock sway bar system.** Rear Installation 18. Place jack stands under the rear end, while supporting the rear end with a floor jack, remove both rear shocks. Slowly lower the floor jack until the rear end sits on the jack stands and remove rear coil springs. 19. Remove rear drive shaft. Non Rubicon models must use short tail shaft conversion kit CE-9069T or CE- 9069HD. 20. Remove and replace upper and lower rear control arms, one at a time. You must drill UPPER control arm holes in the frame and the housing out to 7/16". 21. Drill to 3/8" and then tap the center of the upper bump stop mount and lower coil spring bucket to 7/16-14 thread.** 22. Install the rear track bar relocator by aligning the supplied bracket with the factory track bar bracket and installing the supplied hardware with spacer. After tightening the main bolt, drill the four smaller holes into the factory bracket using the new bracket as a template and install hardware (3 holes are 5/16 and 1 is 3/8"). If using the part #CE-9120R Johnny Joint adjustable rear track bar, it is not necessary to use the supplied spacer with the track bar relocator bracket.** ** Refer to the suplimental instruction sheet specific to this component. 5

6 23. Install rear shock relocator. Must be purchased separate, part #CE If using a Currie rear end it is not necessary to install these brackets, the shock mounts are already relocated on our rear end assemblies. 6

7 24. Install rear springs and rear bump stop kit at this time.** ** Refer to the suplimental instruction sheet specific to this component. 7

8 25. Install rear shocks at this time. 26. Re-install rear track bar with provided spacer to compensate for extra width on the bracket. If using a Currie Johnny Joint adjustable track bar, the spacer is not required.** 27. Go over all nuts and bolts and ensure proper torque specifications. See torque spec. guide on the last page of this instruction sheet. 28. Install wheels and tires and place the vehicle on the ground. 29. Adjust and install the axle end of the front track bar. Center the axle under the vehicle by adjusting the length of the bar. 30. Using an angle finder, measure the caster angle of the front end and set it to 5 degrees. Adjust the upper and lower control arms as necessary to attain the correct angle.** 31. Using an angle finder, measure the pinion angle of the rear end and the angle of the drive shaft. The rear end angle must be 2-3 degrees down in relationship to the drive shaft when using a conventional drive shaft, and 1 degree down when using a double cardan (CV) style drive shaft. Adjust the upper and lower control arms as necessary to attain the correct angle.** 32. Before re-installing the front and rear drive shafts, check for proper drive shaft length. ** Refer to the suplimental instruction sheet specific to this component. 8

9 33. It will be necessary to adjust the toe and re-center the steering wheel by adjusting the drag link. 1/8" toe in is the recommended starting point. 34. Drive the vehicle for 1-2 miles at a moderate speed. 35. Once again go over every nut and bolt in the suspension system and ensure that they are tight. 36. At this time grease every one of the bushings on the suspension arms and the Johnny Joint track bar if equipped. Repeat this step after 500 miles of driving then every 10,000 miles. Torque Specifications by Bolt Size Factory Track Bar Axle 10mm 50 ft/lbs Upper Arms 7/16 60 ft/lbs Track Bar Axle 1/2 75 ft/lbs Lower Arms Track Frame 9/16 5/8 90 ft/lbs 125 ft/lbs Lug Nuts 1/2 85 ft/lbs 9

10 Check length of all of the new Johnny Joint control arms prior to installing. Compare the length of your existing control arms to the Currie Arms. When measuring, measure from the center of the thru bolt hole to the center of the thru-bolt hole on the other end. This measurement can also be determined by measuring the overall length of the control arm and subtracting 2" for upper arms and 2 ½ for lower arms. Currie control arms come preset for a TJ with a 4" lift, a transfer case tailshaft shortening kit, and a CV driveshaft. Front upper arms - 15" c-c Rear upper arms /2" c-c All lower arms /4" c-c CE-9800 Johnny Joint Control Arm Set for Jeep Wrangler TJ / LJ Installation Instructions When custom adjusting the arms for your application, you should never have any more than 3/4" of thread showing from beyond the jam nut. If more than 3/4 is showing after you ve adjusted the arms, you should contact Currie Enterprises technical department to discuss your application and installation. The upper control arms are supplied with 7/16" bolts. The upper control arm frame and housing brackets on Jeep TJ s have metric holes. You will need to drill out these metric holes to accommodate the 7/16 bolts. Torque the 7/16" bolts to 60 ft lbs. of torque. Torque all of the 9/16" bolts on the lower control arms to 90 ft lbs. of torque. Grease all fittings with multi-purpose grease and grease regularly. Check all jam nuts on control arms after 100 miles and regularly thereafter. Re-attach emergency brake cables to control arms with zip ties, discarding the original brackets. Make sure there is enough slack in the cable to allow for wheel travel. NOTE 1: Johnny Joint rod ends are fully rebuildable! Contact Currie Enterprises for details, or order online at NOTE 2: The larger washers supplied with the lower control arms are for use with the the front lower arms where they bolt onto the axle housing. Discard the other set of large washers.

11 CE-9122F TJ front bumpstop kit 1/2 thick aluminum bump stop spacer. 1 3/ Grade 8 flat washer - cast into the urethane /8 C thread x 2 1/4 socket head allen bolt w/ lock washer. Upper urethane bumpstop puck. 2 Lower urethane bumpstop puck. 1 thick aluminum bumpstop spacer. 7/16 C thread x 2 1/4 long grade 8 bolt w/ lock washer. Drill and tap 7/16 course thread hole in the top of spring indexing boss on the coil spring pad on the housing. If you have any further questions during the installation of this kit, please contact a Currie technical representative at:

12 CE-9122R TJ rear bumpstop kit COIL SPRING FITS IN THIS AREA Spacer must be slid in between top 2 coils, and then inserted through the top coil so that the spacer retains the spring to the frame. Billet aluminum bump stop spacer. 1 3/ Grade 8 flat washer - cast into the urethane /8 C thread x 2 1/2 socket head allen bolt w/ lock washer. Upper urethane bumpstop puck. 2 Drill and tap 7/16 a course thread hole in the top of spring indexing boss on the frame, and the coil spring pad on the housing. Lower urethane bumpstop puck. 1 1/16 o.d. - 1/2 grade 8 washer. 3/16 thick steel bumpstop spacer. 7/16 C thread x 1 1/2 long grade 8 bolt w/ lock washer. If you have any further questions during the installation of this kit, please contact a Currie technical representative at:

13 CE-9120TJS & CE-9120TJJ Johnny Joint Adjustable Front Trac Bar for Jeep Wrangler TJ / LJ, and XJ Cherokee Installation Instructions 1. Remove the original trac bar by unbolting it at the housing and then at the frame. Retain the housing bolt and factory nut plate for reuse (retained with CE-9120TJS only - new housing bolt is provided with CE-9120TJJ). An optional, stronger hex head bolt is available through Jeep to replace this bolt and is highly recommended. Jeep part # Using a 5/8 drill bit, drill out the hole in trac bar frame bracket on the frame on the driver s side. 3. Install the 5/8 bolt through the bottom of the Johnny Joint. The bottom of the Johnny Joint is the side without the large flange sticking out of it. 4. Use the special,.200 thick, washer on top of the factory trac bar bracket 5. Install the new trac bar into the hole that you just drilled out from the bottom side of the trac bar frame bracket. Install the nut on the top and snug it down at this time. 6. Center the front axle assembly under the Jeep by measuring from the side of the frame rail to a tread line in the center of your tire. Make sure you measure to the same place on both sides! You can center the axle by using a ratchet strap if necessary. 7. Adjust the track bar to fit the centered axle assembly. When using the CE-9120TJS trac bar, install the original housing bolt through the housing end of the trac bar and thread it back into the original nut plate, but do not tighten. If you are using the CE-9120TJJ trac bar, it will be necessary to drill out the hole in the housing bracket to 1/2 to accept the new, heavier bolt that is supplied. A new nut plate is supplied for the heavier bolt. Remove the stock nut plate and insert the new one in it s place. In some cases it may be necessary to open up the access hole on the bottom of the trac bar bracket to remove the factory nut plate. Thread the new bolt into the new nut plate, but do not tighten. 8. Remeasure your front axle assembly to make sure it s centered. Readjust it if necessary. 9. Now go back and tighten and torque all of the bolts. 5/8 bolt at the frame = 125 ft. lbs. Stock torx bolt on the housing = 50 ft. lbs. Optional 1/2 bolt on the housing = 75 ft. lbs. Jam nut = really really tight! 10. Confirm that the Johnny Joint is straight and in a relatively neutral position, and that the mount on the housing is straight and not in any kind of bind. If anything is misaligned readjust it and retighten it before use!

14 CE-9120R & CE-9123 Johnny Joint Adjustable Rear Trac Bar for Jeep Wrangler TJ / LJ Installation Instructions CE-9120R - Johnny Joint Adjustable Rear Trac Bar WITHOUT Trac Bar Relocation Bracket CE Johnny Joint Adjustable Rear Trac Bar WITH Trac Bar Relocation Bracket (for use with Currie rearends or rearends that already have a relocation bracket installed) 1. Remove the original trac bar by unbolting it at the housing. 2. Install the new Currie bolt-on trac bar relocator bracket by attaching it to the existing bracket with the large supplied bolt. Then go back and mark all of the smaller holes using the bracket as a template. Drill all holes and install bolts. Note 1: If you have a Currie rearend this bracket is not needed - the bracket on the Currie rearend accounts for all of this. Note 2: You may also modify the stock bracket that is already on your rearend. This would require welding and we do not supply instructions for doing this. 3. Before installing the trac bar, put anti-seize lube on the 1 threads. 4. Install the solid bushing end of the trac bar into the frame bracket using the stock bolt. Snug the bolt, but do not tighten. 5. Center the rear axle assembly under the Jeep by measuring from the side of the frame rail to a tread line in the center of your tire. Make sure you measure to the same place on both sides! You can center the axle by using a ratchet strap if necessary, or by pushing on the side of the Jeep. 6. Adjust the track bar to fit the centered axle assembly. Install the Johnny Joint end into the housing bracket and install the greasable bolt through the hole. Snug the bolt, but do night tighten. 8. Remeasure your rear axle assembly to make sure it s centered. Readjust it if necessary. 9. Now go back and tighten and torque all of the bolts. Mounting bolts at the frame and housing = 50 ft. lbs. Jam nut = really really tight! 10. Confirm that the Johnny Joint is straight and in a relatively neutral position, and that the bushing at the frame is straight and not in any kind of bind. If anything is misaligned readjust it and retighten it before use! NOTE: Check torque specs regularly!

Part# CE-9800XJ, CE-9800XJ1, CE-9800XJ2, and CE-9800XJL Jeep Cherokee XJ Lift Kit Installation Instructions

Part# CE-9800XJ, CE-9800XJ1, CE-9800XJ2, and CE-9800XJL Jeep Cherokee XJ Lift Kit Installation Instructions Part# CE-9800XJ, CE-9800XJ1, CE-9800XJ2, and CE-9800XJL 1984 2001 Jeep Cherokee XJ Lift Kit Installation Instructions Please note that modifying the suspension of your Jeep Cherokee will affect the vehicle

More information

Suspension System RS6507B (Rubicon models require end link kit RS6753B for a complete installation)

Suspension System RS6507B (Rubicon models require end link kit RS6753B for a complete installation) 88507 Rev G Suspension System RS6507B (Rubicon models require end link kit RS6753B for a complete installation) Jeep Wrangler (JK) 88507 Rev G READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE

More information

INSTALLATION INSTRUCTIONS 88029

INSTALLATION INSTRUCTIONS 88029 INSTALLATION INSTRUCTIONS 88029 FOR SUSPENSION SYSTEMS RS6503: JEEP WRANGLER (TJ) READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION REV F IMPORTANT NOTES! WARNING: This

More information

Jeep Wrangler (JK) Present

Jeep Wrangler (JK) Present 89107 Rev H Suspension System RS66107 / RS66107B (3 TRAIL SYSTEM) 2012 NEWER JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT

More information

Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5

Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 INSTALLATION GUIDE Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 Take every precaution to make this installation a safe procedure. Make safety the number

More information

INSTALLATION INSTRUCTIONS FOR: RE DOOR JK WRANGLER RE DOOR JK WRANGLER 3.5 STANDARD SUSPENSION SYSTEM

INSTALLATION INSTRUCTIONS FOR: RE DOOR JK WRANGLER RE DOOR JK WRANGLER 3.5 STANDARD SUSPENSION SYSTEM RUBICON MANUFACTURING INC. 3290 MONIER CIR., RANCHO CORDOVA, CA. 95742 916-473-4600 INSTALLATION INSTRUCTIONS FOR: RE7122 2 DOOR JK WRANGLER RE7142 4 DOOR JK WRANGLER 3.5 STANDARD SUSPENSION SYSTEM Safety

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR RANCHO SPORT KIT SUSPENSION SYSTEMS RS6501: JEEP WRANGLER (TJ) READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:

More information

Jeep Wrangler (JK) Present

Jeep Wrangler (JK) Present Suspension System RS66110B (3 SPORT SYSTEM w/ Progressive Coil Springs Front & Rear) 2012 NEWER JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT

More information

Suspension System RS66107 / RS66107B

Suspension System RS66107 / RS66107B 89107 Rev D Suspension System RS66107 / RS66107B (3 TRAIL SYSTEM) 2012 JEEP MODELS EQUIPPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT / EXHAUST

More information

Suspension Upgrade System RS66152 (Upper Adjustable Control Arms)

Suspension Upgrade System RS66152 (Upper Adjustable Control Arms) 89152 Rev B Suspension Upgrade System RS66152 (Upper Adjustable Control Arms) Fits 1997-2006 Jeep Wrangler (TJ / LJ). 89152 Rev B READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING

More information

Suspension System RS66102B

Suspension System RS66102B 890 Rev A Suspension System RS660B ( SPORT SYSTEM) 0 JEEP MODELS EQUIPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFYCATION KIT RS70003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT / EXHAUST CLERANCE ISSUE).

More information

PPM-8023 / PPM-8043 JEEP JK SYNERGY STAGE 3 SUSPENSION SYSTEM Version 1

PPM-8023 / PPM-8043 JEEP JK SYNERGY STAGE 3 SUSPENSION SYSTEM Version 1 SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-8023 / PPM-8043 JEEP JK SYNERGY STAGE 3 SUSPENSION SYSTEM Version 1 GENERAL NOTES: These instructions are also available on our website;

More information

PPM-8022 / PPM-8042 JEEP JK STAGE 2 SYNERGY SUSPENSION SYSTEM Version 1

PPM-8022 / PPM-8042 JEEP JK STAGE 2 SYNERGY SUSPENSION SYSTEM Version 1 POLY PERFORMANCE MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-8022 / PPM-8042 JEEP JK STAGE 2 SYNERGY SUSPENSION SYSTEM Version 1 GENERAL NOTES: These instructions are also available

More information

97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT

97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT 921663U00 97-06 JEEP TJ/LJ LONG ARM UPGRADE KIT Thank you for choosing Rough Country for your suspension needs. This kit is an upgrade kit only. This kit includes frame mounting points and adjustable long

More information

2014+ DODGE RAM LIFT KIT PART# STOP! READ THIS FIRST!

2014+ DODGE RAM LIFT KIT PART# STOP! READ THIS FIRST! NOTE: 2014+ DODGE RAM 2500 8 LIFT KIT PART# 54320 STOP! READ THIS FIRST! **READ THESE ENTIRE INSTRUCTIONS BEFORE STARTING ANYTHING** or chroming, which can damage the strength and structure of the metal,

More information

AEV30213AF Last Updated: 05/24/18. jk wrangler dualsport sc suspension right hand drive INSTALLATION GUIDE

AEV30213AF Last Updated: 05/24/18. jk wrangler dualsport sc suspension right hand drive INSTALLATION GUIDE AEV30213AF Last Updated: 05/24/18 jk wrangler 3.5 4.5 dualsport sc suspension right hand drive INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING

More information

INSTALLATION INSTRUCTIONS WD JEEP WRANGLER TJ 4 SUSPENSION SYSTEM P/N

INSTALLATION INSTRUCTIONS WD JEEP WRANGLER TJ 4 SUSPENSION SYSTEM P/N 1/18/10 INSTALLATION INSTRUCTIONS 97-06 4WD JEEP WRANGLER TJ 4 SUSPENSION SYSTEM P/N 10-45497 NOTE: Each lift kit, and options to lift kits, are packaged separately. Therefore installation procedures are

More information

Suspension System RS66104 & RS66104B (4 Crawler System)

Suspension System RS66104 & RS66104B (4 Crawler System) 89104 Rev B Suspension System RS66104 & RS66104B (4 Crawler System) 2012 JEEP MODELS EQUIPED WITH 3.6L V6 ENGINE NEED EXHAUST MODIFICATION KIT RS720003. OR REPLACEMENT FRONT DRIVESHAFT (DRIVESHAFT / EXHAUST

More information

*1609BAG8* 1609BAG8 JEEP JK 3 1/2 SUSPENSION KIT A

*1609BAG8* 1609BAG8 JEEP JK 3 1/2 SUSPENSION KIT A JEEP JK 3 1/2 SUSPENSION KIT 92160900A *1609BAG8* 1609BAG8 Thank you for choosing Rough Country for your suspension needs. Please read instructions before beginning installation. Check the kit hardware

More information

Jeep Wrangler (JK)

Jeep Wrangler (JK) 89109 Rev B Suspension Systems RS66109BR5 and RS66109BR9 2007 2013 Jeep Wrangler 4 Door Sport and Rubicon Models (2 SPORT SYSTEM) Jeep Wrangler (JK) 2007-2013 89109 Rev B READ ALL INSTRUCTIONS THOROUGHLY

More information

AEV30213AH Last Updated: 04/28/17. jk wrangler dualsport sc suspension INSTALLATION GUIDE

AEV30213AH Last Updated: 04/28/17. jk wrangler dualsport sc suspension INSTALLATION GUIDE AEV30213AH Last Updated: 04/28/17 jk wrangler 3.5 4.5 dualsport sc suspension INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS

More information

4.5 LIFT BOX KIT DODGE RAM 2500 & WD DIESEL ENGINE ONLY FTS23031

4.5 LIFT BOX KIT DODGE RAM 2500 & WD DIESEL ENGINE ONLY FTS23031 4.5 LIFT BOX KIT 2009 2013 DODGE RAM 2500 & 3500 4WD DIESEL ENGINE ONLY FTS23031 FTS23031 Comp. Box 1 FT44058 Hardware Kit Qty Part # Description Qty Description 2 FT44036BK Upper Link 1 9/16"-12 x 3"

More information

Carli Suspension Front Instructions

Carli Suspension Front Instructions Carli Suspension Front Instructions 94-08 DODGE 2500-3500 4X4 SUSPENSION SYSTEM Note: Prior to installation, carefully inspect the vehicle=s steering and drive train components. Be sure to check ball joints,

More information

FORD F-250/350 SUPER DUTY 4WD FTS RADIUS ARM BOX KIT

FORD F-250/350 SUPER DUTY 4WD FTS RADIUS ARM BOX KIT 2005-2007 FORD F-250/350 SUPER DUTY 4WD FTS22099 10 RADIUS ARM BOX KIT 2005-2007 FORD F-250/350 SUPER DUTY 4WD FTS22099 10 RADIUS ARM BOX KIT Qua Part # Description FT30155 Hardware Kit 1 FT30125BK Custom

More information

Installation Guide for the TJ lift kits

Installation Guide for the TJ lift kits Tera Manufacturing, Inc. 5251 South Commerce Dr. Murray, Utah 84107 Phone/801.288.2585 Fax/801.713.2313 www.teraflex.biz INSTALLATION GUIDE Installation Guide for the TJ lift kits 3-inch 4-inch 5-inch

More information

AEV30207AA Last Updated: 2/14/ Dualsport xt suspension INSTALLATION GUIDE

AEV30207AA Last Updated: 2/14/ Dualsport xt suspension INSTALLATION GUIDE AEV30207AA Last Updated: 2/14/12 2.5 Dualsport xt suspension INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS THOROUGHLY BEFORE

More information

Class 8.8 Class MM 18ft/lbs 23 ft/lbs 10MM 32ft/lbs 45ft/lbs 12MM 55ft/lbs 75ft/lbs 14MM 85ft/lbs 120ft/lbs

Class 8.8 Class MM 18ft/lbs 23 ft/lbs 10MM 32ft/lbs 45ft/lbs 12MM 55ft/lbs 75ft/lbs 14MM 85ft/lbs 120ft/lbs 92190500 Jeep Grand Cherokee 93-98 ZJ 4 Longarm Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these

More information

Tools Needed: Class 8.8 Class MM 55ft/lbs 75ft/lbs 14MM 85ft/lbs 120ft/lbs 16MM 130ft/lbs 165ft/lbs 18MM 170ft/lbs 240ft/lbs

Tools Needed: Class 8.8 Class MM 55ft/lbs 75ft/lbs 14MM 85ft/lbs 120ft/lbs 16MM 130ft/lbs 165ft/lbs 18MM 170ft/lbs 240ft/lbs 921788000 JEEP JK 6 LONGARM Rough Country recommends a certified technician install this system. In addition to these instructions, professional knowledge of disassemble/reassembly procedures as well as

More information

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS STEP 1: Park vehicle on level surface and chock rear wheels.

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS STEP 1: Park vehicle on level surface and chock rear wheels. 2007-2013 7.5" GMC/Chevrolet 1500 4WD Suspension Lift kit PRE-INSTALLATION 15004 2 - Cross-member (Fr/Rr) 2 - Sway Bar Drop Bracket 2 - Knuckle (Dr/Pass) 1 - Driver Diff. Bracket 1 - Passenger Diff. Bracket

More information

Suspension System RS66105

Suspension System RS66105 89105 Rev D Requires the following for a complete installation: OE frame bracket removal Transmission Crossmember Kit (see below). 2012 and later models equipped with 3.6l V6 engine need exhaust modification

More information

Installation Instructions

Installation Instructions Installation Instructions Jeep TJ Long Arm Suspension System 1997-2002 JEEP TJ 4WD 6 1997-2002 JEEP TJ 4WD FTS24002 & BK / FTS24003 & BK / FTS44002 & BK PARTS LIST FTS24002BK Jeep TJ 6' Box Kit 1 FTS24003BK

More information

97-06 JEEP TJ / LJ 2 1/2 LONG ARM KIT W/ PERFORMANCE 2.2 SERIES SHOCK ABSORBERS

97-06 JEEP TJ / LJ 2 1/2 LONG ARM KIT W/ PERFORMANCE 2.2 SERIES SHOCK ABSORBERS 92PERF1628 97-06 JEEP TJ / LJ 2 1/2 LONG ARM KIT W/ PERFORMANCE 2.2 SERIES SHOCK ABSORBERS Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician

More information

Installation Guide for TeraFlex three and four-inch Lifts

Installation Guide for TeraFlex three and four-inch Lifts Installation Guide for TeraFlex three and four-inch Lifts Think safety first when installing your new suspension system. Use these instructions to install the TeraFlex 3 or 4-inch lift kits. Information

More information

Installation Guide for TeraFlex three and four-inch TJ Lifts (3T/4T)

Installation Guide for TeraFlex three and four-inch TJ Lifts (3T/4T) Installation Guide for TeraFlex three and four-inch TJ Lifts (3T/4T) Think safety first when installing your new suspension system. Use these instructions to install the TeraFlex 3 or 4-inch lift kits.

More information

RockJock Professional OffRoad Products presents: CE-9900TJR Antirock Sway Bar Kit Installation Instructions Fits

RockJock Professional OffRoad Products presents: CE-9900TJR Antirock Sway Bar Kit Installation Instructions Fits - 1997-2006 Jeep TJ and LJ (Unlimited) 1) CE-9902J...45 Antirock Bar 1) CE-9900TJR-BR...RH frame bracket 1) CE-9900TJR-BL...LH frame bracket 2) CE-99003-JK...Steel Antirock Arms 2) CE-9901D...Antirock

More information

INSTALLATION GUIDE. 3 Dualsport suspension. ram truck 2500/3500. AEV30243AA Last Updated: 04/10/15

INSTALLATION GUIDE. 3 Dualsport suspension. ram truck 2500/3500. AEV30243AA Last Updated: 04/10/15 3 Dualsport suspension AEV30243AA Last Updated: 04/10/15 ram truck 2500/3500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS

More information

97-06 JEEP TJ 3 1/4 PROGRESSIVE COIL/SPACER KIT

97-06 JEEP TJ 3 1/4 PROGRESSIVE COIL/SPACER KIT 92PERF1641 97-06 JEEP TJ 3 1/4 PROGRESSIVE COIL/SPACER KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition

More information

INSTALLATION INSTRUCTIONS FOR: RE7500 SERIES TJ EXTREME DUTY LONG ARM TRI-LINK SYSTEM INCLUDING TJ UNLIMITED

INSTALLATION INSTRUCTIONS FOR: RE7500 SERIES TJ EXTREME DUTY LONG ARM TRI-LINK SYSTEM INCLUDING TJ UNLIMITED RUBICON EXPRESS 3290 MONIER CIR., RANCHO CORDOVA, CA. 95742 916-473-4600 INSTALLATION INSTRUCTIONS FOR: RE7500 SERIES TJ EXTREME DUTY LONG ARM TRI-LINK SYSTEM INCLUDING TJ UNLIMITED Congratulations on

More information

If you have any difficulties at all, please give us a call. Thank you and enjoy your MetalCloak Products!

If you have any difficulties at all, please give us a call. Thank you and enjoy your MetalCloak Products! PRODUCT: TJ/LJ 3.5 Dual Rate Lift RockSport Edition READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL 916-631-8071 M-F 7:00 AM 5:00 PM PST The MetalCloak experience includes the ease of installation

More information

6 LIFT SYSTEM DODGE RAM 2500 & WD MEGA CAB FTS23032

6 LIFT SYSTEM DODGE RAM 2500 & WD MEGA CAB FTS23032 6 LIFT SYSTEM 2009 2013 DODGE RAM 2500 & 3500 4WD 2009 2013 2500 MEGA CAB FTS23032 6 BASIC LIFT SYSTEM 2009 2013 DODGE RAM 2500 & 3500 4WD 2009 2013 2500 MEGA CAB FTS23032 FTS23032 Box Kit FTS23020BK 6"

More information

RAM LIFT KIT PART# STOP! READ THIS FIRST!

RAM LIFT KIT PART# STOP! READ THIS FIRST! NOTE: 2014-2016 RAM 2500 4 LIFT KIT PART# 54340 STOP! READ THIS FIRST! **READ THESE ENTIRE INSTRUCTIONS BEFORE STARTING ANYTHING** or chroming, which can damage the strength and structure of the metal,

More information

2013+ DODGE RAM LIFT KIT PART# STOP! READ THIS FIRST!

2013+ DODGE RAM LIFT KIT PART# STOP! READ THIS FIRST! NOTE: 2013+ DODGE RAM 3500 8 LIFT KIT PART# 54324 STOP! READ THIS FIRST! **READ THESE ENTIRE INSTRUCTIONS BEFORE STARTING ANYTHING** or chroming, which can damage the strength and structure of the metal,

More information

EVO Manufacturing. 2.5 /3.5 Jeep Wrangler JL Enforcer Kit Instruction Manual. for all: EVO-3011, EVO-3012, EVO-3013, EVO-3014 Kits

EVO Manufacturing. 2.5 /3.5 Jeep Wrangler JL Enforcer Kit Instruction Manual. for all: EVO-3011, EVO-3012, EVO-3013, EVO-3014 Kits EVO Manufacturing 2.5 /3.5 Jeep Wrangler JL 2018+ Enforcer Kit Instruction Manual for all: EVO-3011, EVO-3012, EVO-3013, EVO-3014 Kits READ BEFORE INSTALL: 2.5 JL Enforcer/Enforcer Overland kits with either

More information

Suspension System RS6509B

Suspension System RS6509B 88509 Rev H Requires the following for a complete installation: Quick disconnect end link kit RS6756B or solid end link kit RS6753B (for the Rubicon) Rancho exhaust kit RS720001 or RS720002 (or equivalent)

More information

WRANGLER TJ INSTALLATION INSTRUCTIONS Kit #: TJ251K/KN/KST/KSTN TJ401K/KN/KST/KSTN

WRANGLER TJ INSTALLATION INSTRUCTIONS Kit #: TJ251K/KN/KST/KSTN TJ401K/KN/KST/KSTN WRANGLER TJ INSTALLATION INSTRUCTIONS Kit #: TJ251K/KN/KST/KSTN TJ401K/KN/KST/KSTN Before beginning the installation, read these instructions and the enclosed driver s WARNING NOTICE thoroughly and completely.

More information

2.5" & 3.5" SUSPENSION SYSTEM JEEP JK WRANGLER 2 & 4 DOOR MODELS

2.5 & 3.5 SUSPENSION SYSTEM JEEP JK WRANGLER 2 & 4 DOOR MODELS 2.5" & 3.5" SUSPENSION SYSTEM 2007-2018 JEEP JK WRANGLER 2 & 4 DOOR MODELS JSPEC2352 www.jksmfg.com jks@ridefox.com 517-278-1226 RV. 100818 GETTING STARTED Read all warnings, instructions, notes and cautions

More information

2 SUSPENSION SYSTEM JEEP WRANGLER TJ

2 SUSPENSION SYSTEM JEEP WRANGLER TJ 2 SUSPENSION SYSTEM 997-2006 JEEP WRANGLER TJ JSPEC320 www.jksmfg.com jks@sporttruckusainc.com 57-278-226 RV. 09225 GETTING STARTED Read all warnings, instructions, notes and cautions before you begin

More information

97-06 Jeep TJ Wrangler 2. 5 " & 4 " S u s p e n s i o n L i f t Installation Instructions

97-06 Jeep TJ Wrangler 2. 5  & 4  S u s p e n s i o n L i f t Installation Instructions 97-06 Jeep TJ Wrangler 2. 5 " & 4 " S u s p e n s i o n L i f t Installation Instructions Safety Glasses Metric / Standard Wrenches & Sockets Drill / Assorted Drill Bits Floor Jack Jack Stands Measuring

More information

Read and understand all instructions and warnings prior to installation of system and operation of vehicle.

Read and understand all instructions and warnings prior to installation of system and operation of vehicle. 491 W. Garfield Ave., Coldwater, MI 49036 Phone: 517-279-2135 Web/live chat: www.bds-suspension.com E-mail: tech@bds-suspension.com Part#: 014314, 014315 Product: 3" Ultimate Suspension System Application:

More information

KIT # CSS-C SUSPENSION LIFT KIT

KIT # CSS-C SUSPENSION LIFT KIT 14385 Veterans Way Moreno Valley, CA 92553 Phone: (951) 571-0212 Fax: (951) 571-0215 2001-2010 CHEVROLET SILVERADO 1500 AND 2500 HD 4WD AND 2WD PICK-UP 1999-2010 CHEVY 2500 4WD PICK-UPS 2001-2010 2500

More information

97-06 Jeep Wrangler TJ Installation Instructions Kit #: TJ251K-SVX / TJ253K-SVX TJ401K-SVX / TJ403K-SVX

97-06 Jeep Wrangler TJ Installation Instructions Kit #: TJ251K-SVX / TJ253K-SVX TJ401K-SVX / TJ403K-SVX www.skyjacker.com 97-06 Jeep Wrangler TJ Installation Instructions Kit #: TJ251K-SVX / TJ253K-SVX TJ401K-SVX / TJ403K-SVX Before beginning the installation, read these instructions and the enclosed driver

More information

Installation Guide for the JK Wrangler 4-Inch Suspension System with FlexArms

Installation Guide for the JK Wrangler 4-Inch Suspension System with FlexArms INSTALLATION GUIDE Tera Manufacturing, Inc. 5251 South Commerce Dr. Murray, Utah 84107 Phone/801.288.2585 Fax/801.713.2313 www.teraflex.biz Installation Guide for the JK Wrangler 4-Inch Suspension System

More information

07-UP AVALANCHE 7.5 KIT

07-UP AVALANCHE 7.5 KIT 92120900R1 07-UP AVALANCHE 7.5 KIT Thank you for choosing Rough Country for your suspension needs. We appreciate your business!! This kit will not fit vehicles equipped with electric steering or trucks

More information

PRODUCT: JL Dual Rate Lift Kit, RockSport Edition READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 7:00 AM 5:00 PM PST

PRODUCT: JL Dual Rate Lift Kit, RockSport Edition READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 7:00 AM 5:00 PM PST PRODUCT: JL Dual Rate Lift Kit, RockSport Edition READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL 916-631-8071 M-F 7:00 AM 5:00 PM PST REV: A 08-07-2018 II-7633 The MetalCloak experience

More information

JEEP JK 4 LONGARM. Tools Needed: Thank you for choosing Rough Country for your suspension needs.

JEEP JK 4 LONGARM. Tools Needed: Thank you for choosing Rough Country for your suspension needs. 921786000 Thank you for choosing Rough Country for your suspension needs. JEEP JK 4 LONGARM Rough Country recommends a certified technician install this system. In addition to these instructions, professional

More information

2013+ DODGE RAM " Kit PART# STOP! READ THIS FIRST!

2013+ DODGE RAM  Kit PART# STOP! READ THIS FIRST! NOTE: 2013+ DODGE RAM 3500 4" Kit PART# 54346 STOP! READ THIS FIRST! **READ THESE ENTIRE INSTRUCTIONS BEFORE STARTING ANYTHING** or chroming, which can damage the strength and structure of the metal, any

More information

# " Suspension System Jeep Wrangler TJ. 102 S. Michigan Avenue Coldwater, MI

#  Suspension System Jeep Wrangler TJ. 102 S. Michigan Avenue Coldwater, MI #014452 4.5" Suspension System Jeep Wrangler TJ Read and understand all instructions and warnings prior to installation of system and operation of vehicle. SAFETY WARNING BDS Suspension Co. recommends

More information

PRODUCT: JL Game Changer Suspension, RockSport READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 7:00 AM 5:00 PM PST

PRODUCT: JL Game Changer Suspension, RockSport READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL M-F 7:00 AM 5:00 PM PST PRODUCT: JL Game Changer Suspension, RockSport READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL 916-631-8071 M-F 7:00 AM 5:00 PM PST REV: A 06-19-2018 II-7631 The MetalCloak experience includes

More information

»Product» Safety Warning

»Product» Safety Warning J1400, J1401 Installation Instructions 1997-2006 Jeep TJ 4 Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products

More information

2.5" & 3.5" SUSPENSION SYSTEM

2.5 & 3.5 SUSPENSION SYSTEM 2.5" & 3.5" SUSPENSION SYSTEM 2007-2014 JEEP JK WRANGLER 2 & 4 DOOR MODELS JSPEC2352 www.jksmfg.com jks@sporttruckusainc.com 517-278-1226 Rv. 071814 Getting Started Read all warnings, instructions, notes

More information

Jeep Wrangler TJ Rock Ready 6 & 8 Installation Instructions

Jeep Wrangler TJ Rock Ready 6 & 8 Installation Instructions www.skyjacker.com Jeep Wrangler TJ Rock Ready 6 & 8 Installation Instructions * Metric and Standard wrenches and sockets * Allen Wrenches * Assorted Drill Bits * Floor Jack * Jack Stands * Measuring Tape

More information

*1663BAG7* 1663BAG JEEP TJ/LJ LONG ARM KIT 92PERF166300B

*1663BAG7* 1663BAG JEEP TJ/LJ LONG ARM KIT 92PERF166300B 92PERF166300B *1663BAG7* 1663BAG7 97-06 JEEP TJ/LJ LONG ARM KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In

More information

Jeep Grand Cherokee ZJ 4 Suspension Kit

Jeep Grand Cherokee ZJ 4 Suspension Kit 92168800 Jeep Grand Cherokee 93-98 ZJ 4 Suspension Kit Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition

More information

INSTALLATION INSTRUCTION 88578

INSTALLATION INSTRUCTION 88578 INSTALLATION INSTRUCTION 88578 For Rancho Suspension System RS6579B: 4WD Dodge 1500 & 2500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev E IMPORTANT NOTES! WARNING:

More information

*1611BAG2* 1611BAG2 92PERF1611

*1611BAG2* 1611BAG2 92PERF1611 *1611BAG2* 1611BAG2 92PERF1611 97-06 JEEP TJ 2 1/2 X-SERIES SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this

More information

XJ CHEROKEE LIFT KIT

XJ CHEROKEE LIFT KIT 92169600 84-01 6.5 XJ CHEROKEE LIFT KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

INSTALLATION INSTRUCTION 88094

INSTALLATION INSTRUCTION 88094 INSTALLATION INSTRUCTION 88094 FOR RANCHO SUSPENSION SYSTEM RS6594B 4WD & 2WD NISSAN TITAN READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev D IMPORTANT NOTES! WARNING:

More information

97-06 Jeep TJ Wrangler Installation Instructions Models Kit# TJ251K/TJ401K-SX -DX 03 Models Kit# TJ253K/TJ403K-SX -DX

97-06 Jeep TJ Wrangler Installation Instructions Models Kit# TJ251K/TJ401K-SX -DX 03 Models Kit# TJ253K/TJ403K-SX -DX 97-06 Jeep TJ Wrangler Installation Instructions 97-02 Models Kit# TJ251K/TJ401K-SX -DX 03 Models Kit# TJ253K/TJ403K-SX -DX Before beginning the installation, read these instructions and the enclosed driver

More information

INSTALLATION GUIDE. High Steer Kit

INSTALLATION GUIDE. High Steer Kit AEV30212AE Last Updated: 12/09/16 High Steer Kit Designed for 2007 current Jeep JK Wrangler and Wrangler Unlimited models in all trim levels, including Rubicon, with at least 3.0 of suspension lift. INSTALLATION

More information

TOYOTA FJ CRUISER 6 SUSPENSION KIT

TOYOTA FJ CRUISER 6 SUSPENSION KIT 92177000 TOYOTA FJ CRUISER 6 SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

CLAYTON OFF ROAD COR JEEP GRAND CHEROKEE LONG ARM UPGRADE KIT ( WJ)

CLAYTON OFF ROAD COR JEEP GRAND CHEROKEE LONG ARM UPGRADE KIT ( WJ) CLAYTON OFF ROAD COR-4806011 JEEP GRAND CHEROKEE LONG ARM UPGRADE KIT (1999-2004 WJ) NOTES: This product requires general welding, fabrication and automotive mechanic skills. ing should only be done by

More information

84-01 Jeep XJ Cherokee ZJ Grand Cherokee 3" Suspension Lift Installation Instructions

84-01 Jeep XJ Cherokee ZJ Grand Cherokee 3 Suspension Lift Installation Instructions www.skyjacker.com 84-01 Jeep XJ Cherokee 93-98 ZJ Grand Cherokee 3" Suspension Lift Installation Instructions Before beginning the installation, read these instructions and the enclosed driver s WARNING

More information

Sport S/T3 Suspension Installation Guide

Sport S/T3 Suspension Installation Guide 1 Sport S/T3 Suspension Installation Guide #1258250-JK 2-Door Sport S/T3 (No Shocks) #1258200-JK 2-Door Sport S/T3 (w/ Fox Shocks) #1258450-JK 4-Door Sport S/T3 (No Shocks) #1258400-JK 4-Door Sport S/T3

More information

XJ CHEROKEE LIFT KIT

XJ CHEROKEE LIFT KIT 921633XN200 Thank you for choosing Rough Country for your suspension needs. 84-01 4.5 XJ CHEROKEE LIFT KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

»Product» Safety Warning

»Product» Safety Warning J1300, J1301 Installation Instructions 1997-2006 Jeep TJ 3 Suspension Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad Products

More information

INSTALLATION INSTRUCTION 88088

INSTALLATION INSTRUCTION 88088 INSTALLATION INSTRUCTION 88088 For Rancho Suspension Systems RS6588 & RS6589: FORD F-150 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:

More information

84-01 Jeep XJ Cherokee ZJ Grand Cherokee 3" Suspension Lift Installation Instructions

84-01 Jeep XJ Cherokee ZJ Grand Cherokee 3 Suspension Lift Installation Instructions Required Tool List: 84-01 Jeep XJ Cherokee 93-98 ZJ Grand Cherokee 3" Suspension Lift Installation Instructions Safety Glasses Metric / Standard Wrenches & Sockets Drill & Assorted Drill Bits Floor Jack

More information

FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE FORD EXCURSION 4 WHEEL DRIVE FTS & 8 LIFT BOX KIT

FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE FORD EXCURSION 4 WHEEL DRIVE FTS & 8 LIFT BOX KIT 2000-2004 FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE 2000-2005 FORD EXCURSION 4 WHEEL DRIVE FTS421-1 5.5 & 8 LIFT BOX KIT FTS421-1 BOX KIT FT30331 Hdwr Sub-Assembly Kit Qty Part # Description Qty Part # Description

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 5317 & 5318 4 INCH REAR LOWERING KIT 09&UP DODGE RAM 1500 2WD Thank you

More information

JEEP JK 4 SUSPENSION KIT

JEEP JK 4 SUSPENSION KIT 92168100 Thank you for choosing Rough Country for your suspension needs. JEEP JK 4 SUSPENSION KIT Rough Country recommends a certified technician install this system. In addition to these instructions,

More information

2.5" & 3.5" SUSPENSION SYSTEM 2018 JEEP JL WRANGLER 4 DOOR MODELS

2.5 & 3.5 SUSPENSION SYSTEM 2018 JEEP JL WRANGLER 4 DOOR MODELS 2.5" & 3.5" SUSPENSION SYSTEM 2018 JEEP JL WRANGLER 4 DOOR MODELS JSPEC1202/JSPEC1203 www.jksmfg.com jks@sporttruckusainc.com 517-278-1226 RV. 050318 GETTING STARTED Read all warnings, instructions, notes

More information

4331 EUCALYPTUS AVE. ~~ CHINO, CA Fax FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE FTS

4331 EUCALYPTUS AVE. ~~ CHINO, CA Fax FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE FTS 4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185 2000-2003 FORD F-250/350 SUPER DUTY 4 WHEEL DRIVE FTS421-1 5.5 & 8 LIFT BOX KIT PARTS LIST: 1 EA. TRACK ARM BRKT. FT423-100 1 EA. PITMAN

More information

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Dodge Ram WD 6" Suspension Lift Kit

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Dodge Ram WD 6 Suspension Lift Kit 2012-2015 Dodge Ram 1500 4WD 6" Suspension Lift Kit PRE-INSTALLATION 35015 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front

More information

Installation Instructions

Installation Instructions Installation Instructions 5 COILOVER CONVERSION FTS24087 2007-15 JEEP JK PARTS LIST: FTS24087BK 5" JK CO Hoop BX FT50377 Hardware Sub- Assembly QTY Part # Description QTY Part # Description 1 FT50349BK

More information

INSTALLATION MANUAL FOR ROCK KRAWLER SUSPENSION, INC. WJ SHORT ARM SYSTEMS

INSTALLATION MANUAL FOR ROCK KRAWLER SUSPENSION, INC. WJ SHORT ARM SYSTEMS INSTALLATION MANUAL FOR ROCK KRAWLER SUSPENSION, INC. WJ SHORT ARM SYSTEMS FIRST EDITION 8/24/09 Dear customer: Thank you for purchasing the best system on the market for your Jeep Vehicle. We are sure

More information

Installation Guide for TeraFlex 3-inch Lift for Grand Cherokees (3Z)

Installation Guide for TeraFlex 3-inch Lift for Grand Cherokees (3Z) Installation Guide for TeraFlex 3-inch Lift for Grand Cherokees (3Z) Think safety first when installing your new suspension system. Use these instructions to install the TeraFlex 3Z. Information regarding

More information

WRANGLER TJ INSTALLATION INSTRUCTIONS

WRANGLER TJ INSTALLATION INSTRUCTIONS WRANGLER TJ INSTALLATION INSTRUCTIONS 1997-02 Models Kit# TJ251K/TJ401K 2003-06 Models Kit# TJ253K/TJ403K Before beginning the installation, read these instructions and the enclosed driver s WARNING NOTICE

More information

80-96 Ford F150 / Bronco 4WD Class II 4"- 6" Suspension Lift Installation Instructions

80-96 Ford F150 / Bronco 4WD Class II 4- 6 Suspension Lift Installation Instructions www.skyjacker.com Required Tool List: 80-96 Ford F150 / Bronco 4WD Class II 4"- 6" Suspension Lift Installation Instructions Safety Glasses Metric / Standard Wrenches & Sockets Floor Jack Jack Stands Measuring

More information

FTS & 8 RADIUS ARM BOX KIT

FTS & 8 RADIUS ARM BOX KIT FTS22139 6 & 8 RADIUS ARM BOX KIT 2008-2015 FORD F-250/350 SUPER DUTY 4WD 2008 2015 FORD F-250/350 SUPER DUTY 4WD FTS22139 6 & 8 RADIUS ARM KIT FTS22139 6"&8" Radius Arm Box Kit FT30287 Hardware Kit Qty

More information

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4" Suspension Lift Kit

PRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4 Suspension Lift Kit 2015 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front Brake Line

More information

4331 EUCALYPTUS AVE. ~~ CHINO, CA Fax FORD F-250/350 SUPER DUTY 4WD FTS RADIUS ARM BOX KIT

4331 EUCALYPTUS AVE. ~~ CHINO, CA Fax FORD F-250/350 SUPER DUTY 4WD FTS RADIUS ARM BOX KIT 4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185 2005-2007 FORD F-250/350 SUPER DUTY 4WD FTS22099 10 RADIUS ARM BOX KIT 4331 EUCALYPTUS AVE. ~~ CHINO, CA 91710 909-597-7800 Fax 909-597-7185

More information

INSTALLATION MANUAL FOR ROCK KRAWLER SUSPENSION, INC. JK LONG ARM COIL OVER SYSTEMS (Comp Kits and Rock Runner)

INSTALLATION MANUAL FOR ROCK KRAWLER SUSPENSION, INC. JK LONG ARM COIL OVER SYSTEMS (Comp Kits and Rock Runner) INSTALLATION MANUAL FOR ROCK KRAWLER SUSPENSION, INC. JK LONG ARM COIL OVER SYSTEMS (Comp Kits and Rock Runner) SECOND EDITION 10/16/14 1 Dear customer: Thank you for purchasing the best system on the

More information

97-06 JEEP TJ 4 / 6 X-SERIES SUSPENSION KIT

97-06 JEEP TJ 4 / 6 X-SERIES SUSPENSION KIT 921661X00 97-06 JEEP TJ 4 / 6 X-SERIES SUSPENSION KIT Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician to install this system. In addition

More information

This 6 suspension system was developed for 37x12.50x17 tire on an after market wheel w/ 4.5 back spacing.

This 6 suspension system was developed for 37x12.50x17 tire on an after market wheel w/ 4.5 back spacing. Thank you for choosing Rough Country for your suspension needs. 921560200C *1560BAG4* 1560BAG4 2017 F250 6 4-LINK SUSPENSION KIT Rough Country recommends a certified technician installs this system. In

More information

97-06 JEEP TJ 4 SUSPENSION KIT

97-06 JEEP TJ 4 SUSPENSION KIT 92190600 Thank you for choosing Rough Country for your suspension needs. 97-06 JEEP TJ 4 SUSPENSION KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

CLAYTON OFF ROAD COR , COR JEEP WRANGLER 2.5", 3.5" ENTRY LEVEL LIFT KIT 2 DR (2018 & UP, JL)

CLAYTON OFF ROAD COR , COR JEEP WRANGLER 2.5, 3.5 ENTRY LEVEL LIFT KIT 2 DR (2018 & UP, JL) CLAYTON OFF ROAD COR-2909002, COR-2909010 JEEP WRANGLER 2.5", 3.5" ENTRY LEVEL LIFT KIT 2 DR (2018 & UP, JL) NOTES: This product may require general welding, fabrication and automotive mechanic skills.

More information

*1333BAG1* 1333BAG DODGE LIFT KIT

*1333BAG1* 1333BAG DODGE LIFT KIT 921333300 *1333BAG1* 1333BAG1 2012-18 DODGE 1500 4 LIFT KIT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition

More information

07-10 JEEP (JK) WRANGLER/RUBICON 4.5 SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS FLEX JOINT CONTROL ARMS

07-10 JEEP (JK) WRANGLER/RUBICON 4.5 SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS FLEX JOINT CONTROL ARMS 3651 N. Hwy. 89 Chino Valley, AZ 86323 (928) 636-7080 07-10 JEEP (JK) WRANGLER/RUBICON 4.5 SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS FLEX JOINT CONTROL ARMS J4614 (No Driveshafts) J4615 (With Driveshafts

More information

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE

AEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND

More information

Suspension System RS6582B

Suspension System RS6582B Suspension System RS6582B Tahoe/Yukon READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING: This suspension system will enhance the off-road performance

More information